The objects described here can be monitored with the IPHost Network Monitor.
You can start SNMP monitoring using free 30-day trial version of IPHost right now.
OID list for port enable
- as Dot1x Port Enable
- asDot1xPortEnable 1.3.6.1.4.1.890.1.5.1.1.31.1.1 (defined in ZYXEL-accessSwitch-MIB)
The option defines if the port enables 802.1x settings. - as Dot1x Port Re Authentication Enable
- asDot1xPortReAuthEnable 1.3.6.1.4.1.890.1.5.1.1.31.1.3 (defined in ZYXEL-accessSwitch-MIB)
The option defines if the port enables 802.1x re-authentication. - dot1d Stp Port Enable
- dot1dStpPortEnable 1.3.6.1.2.1.17.2.15.1.4 (defined in BRIDGE-MIB)
The enabled/disabled status of the port. - atmx Port Enable ILMI
- atmxPortEnableILMI 1.3.6.1.4.1.800.2.4.1.1.1.20 (defined in XYLAN-ATM-MIB)
ILMI Enable. - dsx1 Port Config Yel Alarm Detect Enable
- dsx1PortConfigYelAlarmDetectEnable 1.3.6.1.4.1.800.2.11.1.1.1.6 (defined in XYLAN-DS1-MIB)
This object indicates whether Yellow Alarm should be detected. - v Stp Port Enable
- vStpPortEnable 1.3.6.1.4.1.800.2.2.5.19.1.7 (defined in XYLAN-VLAN-MIB)
The enabled/disabled status of the port. - dot1d Stp Port Enable
- dot1dStpPortEnable 1.3.6.1.2.1.17.2.15.1.4 (defined in rfc1493)
The enabled/disabled status of the port. - els100 Sys Com Port Enable
- els100SysComPortEnable 1.3.6.1.4.1.52.1011.1.13 (defined in ctels100-ng-mib)
The administrative state of the Com Port. - els100 Port Autoneg Enable
- els100PortAutonegEnable 1.3.6.1.4.1.52.1011.2.1.9 (defined in ctels100-ng-mib)
The auto-negotiation status of the port, either enable or disable. When in the enable (2) state, the port will automatically configure its duplex and speed operation. - Cabletron Pvst Stp Port Enable
- ctPvstStpPortEnable 1.3.6.1.4.1.52.4.1.2.3.2.2.6.1.5 (defined in ctron-bridge-mib)
The enabled/disabled status of the port. - Cabletron Remote Ext Physical Port Protocol Manager Enable
- ctRemExtPhysPortProtMgrEnable 1.3.6.1.4.1.52.4.1.2.7.2.1.6.1.4 (defined in ctron-remote-access-mib)
This object identifies an instance of the the enable flag of Protocol Manager residing on this physical port. - Token Ring Port Group Ring Ports Enable
- tRingPortGrpRingPortsEnable 1.3.6.1.4.1.52.4.1.2.1.1.2.1.1.6 (defined in dot5-log-mib)
Setting this object to enable will cause all the ring ports in this port group to be enabled. Setting this object to noEnable will have no effect on the ring ports in this port group. When read this object will always return noEnable. - Token Ring Port Management Ring Out Enable
- tRingPortMgmtRingOutEnable 1.3.6.1.4.1.52.4.1.2.1.1.3.1.1.1.8 (defined in dot5-log-mib)
This object, when written, permits the port to function as either a ring out port or a station port, if available. If this selection is not supported by this port, then any write to this object will return a BADSETINFO error. When read, this object will return the state of the port with respect to this mode of operation. The default state of this object, if available, is disabled; otherwise it is notAvailable. - Token Ring Port Station Insertion Trap Enable
- tRingPortStnInsertionTrapEnable 1.3.6.1.4.1.52.4.1.2.1.1.3.2.1.1.7 (defined in dot5-log-mib)
A write of enabled to this object permits the port inserted and port deinserted traps to be sent when phantom current has been asserted or removed, respectively, on this station port. A write of disabled prevents the traps from being sent. The default state of this object is disabled. - dot5 Physical Management Port Common Ring Out Enable
- dot5PhysMgmtPortCommonRingOutEnable 1.3.6.1.4.1.52.4.1.1.6.1.3.1.1.1.8 (defined in dot5-phys-mib)
This object, when written, permits the port to function as either a ring out port or a station port, if available and if the MIM board on which this station port is resident lies within the domain of the device. If this selection is not supported by this port, or if the MIM falls outside of the domain of the device, the SNMP error BadValue will be returned. When read, this object will return the state of the port with respect to this mode of operation. The default state of this object, if available, is disabled; otherwise it is notAvailable. - dot5 Physical Management Port Station Insertion Trap Enable
- dot5PhysMgmtPortStnInsertionTrapEnable 1.3.6.1.4.1.52.4.1.1.6.1.3.2.1.1.5 (defined in dot5-phys-mib)
A write of enabled or disabled to this object permits or inhibits the sending of the port inserted and port deinserted traps when phantom current is asserted or removed, respectively, on this station port, provided the MIM on which this port is resident falls within the domain of the device. If the MIM falls outside of the domain of the device, the SNMP error BadValue will be returned. When read this object will repond with the last write request made. The default state of this object is disabled. - port Traffic Enable
- portTrafficEnable 1.3.6.1.4.1.43.1.12.3.1.1.6.5.3.1.1 (defined in irm3-mib)
Enable the sending of port level traffic traps for this port. - port Collsions Enable
- portCollsEnable 1.3.6.1.4.1.43.1.12.3.1.1.6.5.3.2.1 (defined in irm3-mib)
Enable the sending of port level collsion alarms. - port Error Enable
- portErrorEnable 1.3.6.1.4.1.43.1.12.3.1.1.6.5.3.3.1 (defined in irm3-mib)
Enable the sending of port level error alarms. - port Broad Enable
- portBroadEnable 1.3.6.1.4.1.43.1.12.3.1.1.6.5.3.4.1 (defined in irm3-mib)
Enable the sending of port level broadcast alarms. - port Traffic Enable
- portTrafficEnable 1.3.6.1.4.1.43.1.12.3.1.1.6.5.3.1.1 (defined in repeater-mib-2)
Enable or disable the checking for port level traffic thresholds getting exceeded. - port Collsions Enable
- portCollsEnable 1.3.6.1.4.1.43.1.12.3.1.1.6.5.3.2.1 (defined in repeater-mib-2)
Enable or disable the checking for port level collision thresholds getting exceeded. - port Error Enable
- portErrorEnable 1.3.6.1.4.1.43.1.12.3.1.1.6.5.3.3.1 (defined in repeater-mib-2)
Enable or disable the checking for port level error thresholds getting exceeded. - port Broad Enable
- portBroadEnable 1.3.6.1.4.1.43.1.12.3.1.1.6.5.3.4.1 (defined in repeater-mib-2)
Enable the sending of port level broadcast alarms. - Repeater Port Group Alarm Traffic Enable
- rptrPortGrpAlarmTrafEnable 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.2 (defined in repeater-rev4-mib)
Get returns whether traffic alarms are enabled/disabled. Set allows for enabling/disabling of traffic alarms. - Repeater Port Group Alarm Error Enable
- rptrPortGrpAlarmErrEnable 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.8 (defined in repeater-rev4-mib)
Get returns whether error alarms are enabled/disabled. Set allows for enabling/disabling of error alarms. - Repeater Port Alarm Traffic Enable
- rptrPortAlarmTrafEnable 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.3 (defined in repeater-rev4-mib)
Get returns whether traffic alarms are enabled/disabled. Set allows for enabling/disabling of traffic alarms. - Repeater Port Alarm Collision Enable
- rptrPortAlarmCollEnable 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.6 (defined in repeater-rev4-mib)
Get returns whether collision alarms are enabled/disabled. Set allows for enabling/disabling of collision alarms. - Repeater Port Alarm Error Enable
- rptrPortAlarmErrEnable 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.9 (defined in repeater-rev4-mib)
Get returns whether error alarms are enabled/disabled. Set allows for enabling/disabling of error alarms. - Repeater Port Alarm Broad Enable
- rptrPortAlarmBroadEnable 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.13 (defined in repeater-rev4-mib)
Get returns whether broadcast alarms are enabled/disabled. Set allows for enabling/disabling of broadcast alarms. - xst Instance Port Enable
- xstInstancePortEnable 1.3.6.1.4.1.52.4.12.30.1.5.6.5.1.5 (defined in v2h124-24-mib)
The enabled/disabled status of the port. - prio Ip Port Enable Status
- prioIpPortEnableStatus 1.3.6.1.4.1.52.4.12.30.1.13.6 (defined in v2h124-24-mib)
Whether IP Port priority look-up is enabled. - Enterasys Dot3ad Aggregate Port Enable
- etsysDot3adAggPortEnable 1.3.6.1.4.1.5624.1.2.35.1.2.1.1.1 (defined in enterasys-ieee8023-lag-mib-ext-mib)
The enabled/disabled status of the IEEE 802.3ad link aggregation functionality on this port. A value of disabled(2) will prevent the transmission and processing of LACP BPDUs on this port. - Enterasys Ietf Bridge Dot1d Stp Port Stp Enable
- etsysIetfBridgeDot1dStpPortStpEnable 1.3.6.1.4.1.5624.1.2.31.1.1.1.1.1 (defined in enterasys-ietf-bridge-mib-ext-mib)
The enabled/disabled status of the Spanning Tree protocol on the port. - Enterasys Ietf Bridge Dot1d Stp Loop Protect Port Cist Enable
- etsysIetfBridgeDot1dStpLoopProtectPortCistEnable 1.3.6.1.4.1.5624.1.2.31.1.6.1.1.1 (defined in enterasys-ietf-bridge-mib-ext-mib)
The enabled/disabled status of the Loop Protect feature for this port on the Common and Internal Spanning Tree (CIST). - Enterasys MAC Authentication Port Enable
- etsysMACAuthenticationPortEnable 1.3.6.1.4.1.5624.1.2.25.1.2.1.1.4 (defined in enterasys-mac-authentication-mib)
When set to enabled(1), a platform dependent triggering mechanism initiates an authentication exchange using a MAC address for authentication credentials. When disabled(2), authentication attempts are disabled and all currently authenticated MAC sessions or those in the process of authentication on this port are terminated. - Enterasys Mstp Port Extension Loop Protect Enable
- etsysMstpPortExtnLoopProtectEnable 1.3.6.1.4.1.5624.1.2.28.1.4.4.1.2 (defined in enterasys-mstp-mib)
The enabled/disabled status of the Loop Protect functionality for this port on this MSTI. - Enterasys Multi Authentication Port Trap Enable
- etsysMultiAuthPortTrapEnable 1.3.6.1.4.1.5624.1.2.46.1.2.1.1.6 (defined in enterasys-multi-auth-mib)
This object allows for the enabling or disabling of each trap on a per interface basis. Setting a given bit to a value of 1 allows traps of that type to be sent for events on that interface. Setting a given bit to a value of 0 disallows traps of that type to be sent for events on that interface. The individual bits correlate to specific traps as follows: BIT NOTIFICATION ---------------------------------------------------------------- authSuccessTrap(0) etsysMultiAuthSuccess authFailedTrap(1) etsysMultiAuthFailed authTerminatedTrap(2) etsysMultiAuthTerminated maxNumUsersReachedTrap(3) etsysMultiAuthMaxNumUsersReached DEFVAL { { } } ::= { etsysMultiAuthPortEntry 6 } SYNTAX SEQUENCE OF EtsysMultiAuthPortTypeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION A table of per port, per authentication type information. - Enterasys Port Web Authentication System Port Web Authentication Name Services Enable
- etsysPwaSystemPwaNameServicesEnable 1.3.6.1.4.1.5624.1.2.8.1.4 (defined in enterasys-pwa-mib)
The enable state of the name services application. Enabling this object turns on the Domain Name Service (DNS) and the Windows Internet Naming Services (WINS) clients. These clients will resolve only requests for the etsysPwaSystemAuthHostName. Disabling this object would require users in the network to know and use the etsysPwaSystemAuthIPAddress of this system. - Enterasys Radius Snooping Port Enable
- etsysRadiusSnoopingPortEnable 1.3.6.1.4.1.5624.1.2.62.2.1.2.1.1.2 (defined in enterasys-radius-snooping-mib)
When set to enabled(1), a platform dependent triggering mechanism initiates the detection of RADIUS traffic sent by edge devices. These RADIUS requests in conjuntion with their respective responses allow for RADIUS Snooping to process these sessions. When disabled(2), RADIUS Snooping detection is disabled and all currently authenticated sessions or those in the process of authentication on this port are terminated. Maintaining the value of this object across agent reboots is REQUIRED. - serial Port Enable
- serialPortEnable 1.3.6.1.4.1.351.110.4.1.1.1.3 (defined in BASIS-SERIAL-MIB)
This object is used for enabling/disabling serial port.
