The objects described here can be monitored with the IPHost Network Monitor.
You can start SNMP monitoring using free 30-day trial version of IPHost right now.
OID list for max traffic
- Xerox HOST RESOURCES Device Traffic Input Max Size
- xcmHrDevTrafficInputMaxSize 1.3.6.1.4.1.253.8.53.7.2.1.8 (defined in XEROX-HOST-RESOURCES-EXT-MIB)
A device input maximum size, or zero if infinite, used by system administrators and end users of this device. Usage: It is device specific how (or if) this limit object is used (eg, disk with 'xcmHrDevTrafficInputUnit' of 'mediaBlock' might limit block count of a single disk read to '50'). - Xerox HOST RESOURCES Device Traffic Output Max Size
- xcmHrDevTrafficOutputMaxSize 1.3.6.1.4.1.253.8.53.7.2.1.9 (defined in XEROX-HOST-RESOURCES-EXT-MIB)
A device output maximum size, or zero if infinite, used by system administrators and end users of this device. Usage: It is device specific how (or if) this limit object is used (eg, disk with 'xcmHrDevTrafficOutputUnit' of 'mediaBlock' might limit block count of a single disk write to '50'). - Cisco Gateway GPRS Support Node Umts Qos Cac Max Traffic Class
- cggsnUmtsQosCacMaxTrafficClass 1.3.6.1.4.1.9.9.241.1.3.4.3.1.5 (defined in CISCO-GGSN-QOS-MIB)
This object defines the highest traffic class that can be accepted. If the requested traffic class is higher than configured one, the PDP context create request will be rejected. Traffic class can not be downgraded. - ip Traffic Profile Max Ds Rate
- ipTrafficProfileMaxDsRate 1.3.6.1.4.1.3646.1300.2.11.2.2.1.3 (defined in ASKEY-DSLAM-VC-VLAN-MIB)
The maximum transmit data rate in Kbps in the down-stream direction of this IP traffic profile. The specified data rate will be rounded to the largest multiple of 32. - DOCSIS Ietf Qos Param Set Max Traffic Rate
- docsIetfQosParamSetMaxTrafficRate 1.3.6.1.2.1.127.1.2.1.3 (defined in DOCS-IETF-QOS-MIB)
Service Flow in bits/sec. Must count all MAC frame data PDU from the bytes following the MAC header HCS to the end of the CRC. The number of bytes forwarded is limited during any time interval. The value 0 means no maximum traffic rate is enforced. This object applies to both upstream and downstream Service Flows. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, the default value of this object is 0. If the parameter is not applicable, it is reported as 0. - DOCSIS Ietf Qos Param Set Max Traffic Burst
- docsIetfQosParamSetMaxTrafficBurst 1.3.6.1.2.1.127.1.2.1.4 (defined in DOCS-IETF-QOS-MIB)
for this parameter set. The value is calculated from the byte following the MAC header HCS to the end of the CRC. This object is applied in conjunction with docsIetfQosParamSetMaxTrafficRate to calculate maximum sustained traffic rate. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, the default value of this object for scheduling types bestEffort (2), nonRealTimePollingService(3), and realTimePollingService(4) is 3044. If this parameter is not applicable, it is reported as 0. REFERENCE "SP-RFIv2.0-I06-040804, Appendix C.2.2.5.3 - DOCSIS Ietf Qos Service Class Max Traffic Rate
- docsIetfQosServiceClassMaxTrafficRate 1.3.6.1.2.1.127.1.8.1.4 (defined in DOCS-IETF-QOS-MIB)
Template for docsIetfQosParamSetMaxTrafficRate. - DOCSIS Ietf Qos Service Class Max Traffic Burst
- docsIetfQosServiceClassMaxTrafficBurst 1.3.6.1.2.1.127.1.8.1.5 (defined in DOCS-IETF-QOS-MIB)
Template for docsIetfQosParamSetMaxTrafficBurst. - DOCSIS Qos Param Set Max Traffic Rate
- docsQosParamSetMaxTrafficRate 1.3.6.1.4.1.2011.2.25.127.7.1.2.1.6 (defined in DOCS-QOS-MIB)
service flow in bits/sec. Must count all MAC frame data PDU from the bytes following the MAC header HCS to the end of the CRC. The number of bytes forwarded is limited during any time interval. The value 0 means no maximum traffic rate is enforced. This object applies to both upstream and downstream service flows. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, the default value of this object is 0. If the parameter is not applicable, it is reported as 0. REFERENCE "SP-RFIv1.1-I07-010829, Appendix C.2.2.5.2 - DOCSIS Qos Param Set Max Traffic Burst
- docsQosParamSetMaxTrafficBurst 1.3.6.1.4.1.2011.2.25.127.7.1.2.1.7 (defined in DOCS-QOS-MIB)
for this parameter set. The value is calculated from the byte following the MAC header HCS to the end of the CRC. This object is applied in conjunction with docsQosParamSetMaxTrafficRate to calculate maximum sustained traffic rate. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, the default value of this object for scheduling types bestEffort (2), nonRealTimePollingService(3), and realTimePollingService(4) is 1522. If this parameter is not applicable, it is reported as 0. REFERENCE "SP-RFIv1.1-I07-010829, Appendix C.2.2.5.3 - DOCSIS Qos Service Class Max Traffic Rate
- docsQosServiceClassMaxTrafficRate 1.3.6.1.4.1.2011.2.25.127.7.1.8.1.5 (defined in DOCS-QOS-MIB)
Template for docsQosParamSetMaxTrafficRate. - DOCSIS Qos Service Class Max Traffic Burst
- docsQosServiceClassMaxTrafficBurst 1.3.6.1.4.1.2011.2.25.127.7.1.8.1.6 (defined in DOCS-QOS-MIB)
Template for docsQosParamSetMaxTrafficBurst. - qos Switch Traffic Class Max Bandwidth
- qosSwitchTrafficClassMaxBandwidth (defined in AT-QOS-MIB)
Specifies the maximum bandwidth available to this traffic class. Traffic under this bandwidth will be designated as bandwidth class 2. The value 2147483647 indicates that there is no limit on the maximum bandwidth for this traffic class. - qos Switch Traffic Class Max Burst Size
- qosSwitchTrafficClassMaxBurstSize (defined in AT-QOS-MIB)
Specifies the maximum bandwidth above the bandwidth specified by qosSwitchTrafficClassMaxBandwidth before traffic is marked as bandwidth class 3.
