SNMP control_operation monitoring

MIBs list

SNMP control_operation monitoring

The objects described here can be monitored with the IPHost Network Monitor. You can start SNMP monitoring using free 30-day trial version of IPHost right now.

OID list for control operation

Frame Relay Interface Vc Control Compression Operation Phase
frxVcControlCompressionOperPhase 1.3.6.1.4.1.800.2.8.2.1.1.5 (defined in XYLAN-FRAME-RELAY-MIB)
This object reports the current phase (state) of compression for this virtual circuit if the Compression Admin Status is set to enable. If the compression Admin status is set to disabled, then this object will report as disabled. Otherwise the value reflects whether compression is currently inactive or failed negotiation (disabled) is under negotiation (initialization) or active (operation). Possible causes of disabled are a failed negotiation, virtual circuit inactive, the other side not supporting compression, etc. For a description of the phases (states), see Frame Relay Forum Implementation aggreement on Data Compression (FRF.9)
lapb Operation Control Field
lapbOperControlField 1.3.6.1.2.1.10.16.2.1.3 (defined in rfc1381)
The current operating size of the sequence numbers used to number frames.
sdlc Link Stations Operation Last Fail Control In
sdlcLSOperLastFailCtrlIn 1.3.6.1.2.1.41.1.2.2.1.17 (defined in rfc1747)
This object reflects the last control octet or octets (depending on modulus) received by this SDLC link station at the time of the last failure. If the link station has not failed, then this value has no meaning.
sdlc Link Stations Operation Last Fail Control Out
sdlcLSOperLastFailCtrlOut 1.3.6.1.2.1.41.1.2.2.1.18 (defined in rfc1747)
This object reflects the last control octet or octets (depending on modulus) sent by this SDLC link station at the time of the last failure. If the link station has not failed, then this value has no meaning.
Network AppleTalk Host Control Operation STATUS
nwAtHostCtlOperSTATUS 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.2.1.1.3 (defined in ctron-appletalk-router-mib)
Indicates the current operating condition of the AARP Table on the router port for which the entry exists.
Cabletron Flow Control Half Duplex Operation Status
ctFlowCtlHalfDuplexOperStatus 1.3.6.1.4.1.52.4.1.2.4.2.2.1.1.2 (defined in ctron-ethernet-parameters)
The current operational status of back pressure on this port.
Cabletron Flow Control Pause Operation Status
ctFlowCtlPauseOperStatus 1.3.6.1.4.1.52.4.1.2.4.2.2.1.1.5 (defined in ctron-ethernet-parameters)
The current operational status of full duplex flow control on this port. A value of unknown(5) will be returned for any port which has a Pause Frame Admin Status of autonegotiate(5), as specified by ctFlowCtlPauseAdminStatus, but is in an unknown Auto-Negotiation state.
Network Ip Host Control Operation Status
nwIpHostCtlOperStatus 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1.3 (defined in ctron-ip-router-mib)
Indicates the current operating condition of the IP Host Address cache on the router port for which the entry exists.
Network Routing If Forward Control Operation Status
nwRtrIfFwdCtrOperStatus 1.3.6.1.4.1.52.4.2.2.2.2.4.2.1.1.2 (defined in ctron-routers-mib)
Indicates the current operating condition of the routing services on the router port. The value of nwRtrIfFwdCtrOperStatus indicates whether counting is active for the routing services on the routing port.
port X25 Operation Flow Control Negotiation
portX25OperFlowCtrlNeg 1.3.6.1.4.1.173.7.3.1.6.1.2 (defined in netlink-specific-mib)
A flag which if set, permits negotiation of the flow control parameters on a per call basis. If N is selected, the default packet and window sizes will be used. If Y is selected, the packet or window size in a call packet (up to the configured Max Packet Size or Max Window Size) is used.
bsci Device Operation Control Unit ID
bsciDevOperControlUnitID 1.3.6.1.4.1.173.7.3.4.6.1.1 (defined in netlink-specific-mib)
Control Unit identifier.
appn Is In Globe Control Operation Status
appnIsInGlobeCtrOperStatus 1.3.6.1.2.1.34.4.1.6.1.2 (defined in APPN-MIB)
Indicates whether or not the intermediate session counts are active. The counts referred to here are the eight objects in the AppnIsInTable, from appnIsInP2SFmdPius through appnIsInS2PNonFmdBytes. These eight counts are of type Unsigned32 rather than Counter32 because when this object enters the notActive state, either because a Management Station has set appnInInGlobeCtrAdminStatus to notActive or because of a locally-initiated transition, the counts are all reset to 0. The values for this object are: notActive(1): collection of counts is not active; if it is queried, a count returns the value 0. active(2): collection of counts is active.
Cisco Bridge Control Protocol Operation Table
bcpOperTable 1.3.6.1.4.1.9.9.275.1.1 (defined in CISCO-BCP-MIB)
Table containing the status of the local BCP entity that is related to the operation of Bridging Control Protocol.
Cisco Bridge Control Protocol Operation Entry
bcpOperEntry 1.3.6.1.4.1.9.9.275.1.1.1 (defined in CISCO-BCP-MIB)
Operational status information for a particular BCP link. For all entries in ifTable with ifType ppp(23), there will be an entry in this table.
Cisco Bridge Control Protocol Operation Status
bcpOperStatus 1.3.6.1.4.1.9.9.275.1.1.1.1 (defined in CISCO-BCP-MIB)
The operational status of the Bridge Control Protocol. The possible values are : open(1) - the BCP link is up and both ends are configured in the compatible manner. closed(2) - the BCP link is down and neither ends are configured. listening(3) - the local BCP entity is configured and the remote end is not configured compatibly.
Cisco Access Control List QoS If Operation Trust State
caqIfOperTrustState 1.3.6.1.4.1.9.9.179.1.2.1.1.5 (defined in CISCO-CATOS-ACL-QOS-MIB)
This object is used to indicate the operational trust state of an interface. The operational trust state may or may not be identical to the config trust state denoted by caqIfTrustStateConfig. The value of this object depends on the runtime conditions such as whether the interface is configured to trust a certain type of device as denoted by caqIfTrustDevice as well as whether a device of the trusted type is connected to the interface. For example, if the interface is configured to only trust Cisco IP Phone and the phone is not connected to the interface at runtime, the operational trust state of this interface will have the untrusted(1) value even if the trustCoS(2) value is configured in caqIfTrustStateConfig. This object is only instantiated if the platform supports trust device configuration. If the object is untrusted(1), then the DSCP assigned to the packet is the DSCP specified by classification rule obtained from the matching ACE (Access Control Entry). ACE is a filter that is used to identify flows with certain characteristics. It includes fields such as ingress/egress ports, L2 addresses, L3 addresses , TCP/UDP port number. If this object is trustCoS(2), then the DSCP assigned to the packet is the layer2 CoS of the packet mapped to a DSCP by the CoS-to-DSCP mapping defined in object caqCosToDscpDscp. When this object is trustIpPrec(3), a DSCP is assigned to an IP packet according to the IP-Precedence-to-DSCP mapping defined by the values contained in caqIpPrecToDscpTable. For non-IP packets, trustIpPrec(3) has identical behavior as trustCoS(2). When this object is trustDscp(4), the DSCP contained in an IP packet is trusted as being the correct value to assign to it. For non-IP packets, trustDscp(4) has identical behavior as trustCoS(2).
Cisco Access Control List QoS Ip Operation Acl Feature
caqIpOperAclFeature 1.3.6.1.4.1.9.9.179.1.2.4.1.1 (defined in CISCO-CATOS-ACL-QOS-MIB)
An index indicates the feature to which the operational IP ACLs mapped at this interface are applied. 'ingressIpQos' indicates the ACL mapped at this interface is used to classify ingress IP traffic for QoS feature. 'egressIpQos' indicates the ACL mapped at this interface is used to classify egress IP traffic for QoS feature. 'ipSecurity' indicates the ACL mapped at this interface is used to classify IP traffic for security feature.
Cisco Access Control List QoS Ip Operation Acl Name
caqIpOperAclName 1.3.6.1.4.1.9.9.179.1.2.4.1.2 (defined in CISCO-CATOS-ACL-QOS-MIB)
This object indicates the name of an operational IP ACL which is mapped at this interface to classify IP traffic for feature denoted by caqIpOperAclFeature object.
Cisco Access Control List QoS Ip Ace Destination Port Operation
caqIpAceDestPortOp 1.3.6.1.4.1.9.9.179.1.3.2.1.14 (defined in CISCO-CATOS-ACL-QOS-MIB)
Indicates how a packet's destination TCP/UDP port number is to be compared. If the caqIpAceProtocolType object in the same row does not indicate TCP or UDP, this object has to be 'noOperator(1)' and cannot be changed while this row is active, i.e., the value of caqIpAceStatus in the same row has the value 'active(1)'. 'noOperator(1)', which is the default value, means that no comparison is to be made with the destination TCP/UDP port number. lt(2) means less than. gt(3) means greater than. eq(4) means equal. neq(5) means not equal. Those 4 operators are using the caqIpAceDestPort object as an operand which is the only one needed. range(6) means that it compares the port value between two numbers, so this operator needs 2 operands. One operand is the starting port number of the range which is caqIpAceDestPort object, and the other operand is the ending port number of the range which the caqIpAceDestPortRange object is in.
Cisco Access Control List QoS Ip Download Ace Destination Port Operation
caqIpDownloadAceDestPortOp 1.3.6.1.4.1.9.9.179.1.10.2.1.13 (defined in CISCO-CATOS-ACL-QOS-MIB)
Indicates how a packet's destination TCP/UDP port number is to be compared. 'noOperator', which is the default value, means that no comparison is to be made with the destination TCP/UDP port number. 'lt' means less than. 'gt' means greater than. 'eq' means equal. 'neq' means not equal. Those 4 operators are using the caqIpDownloadAceDestPort object as an operand which is the only one needed. 'range' means that it compares the port value between two numbers, so this operator needs 2 operands. One operand is the starting port number of the range which is caqIpDownloadAceDestPort object, and the other operand is the ending port number of the range which the caqIpDownloadAceDestPortRange object is in.
Cisco Access Control List QoS Ip Operation Classifier Group
caqIpOperClassifierGroup 1.3.6.1.4.1.9.9.179.3.2.54 (defined in CISCO-CATOS-ACL-QOS-MIB)
A collection of objects provides the operational mapping of IP ACLs to each applicable interface.
Cisco Channel Interface Processor Transmission Groups Llc Operation Local Control Point
cipTgLlcOperLocalCP 1.3.6.1.4.1.9.9.73.1.1.2.1.3 (defined in CISCO-CIPTG-MIB)
The local control point name for the host. The name is extracted from the XID3s received from the host and sent to the remote network node. While the LLC TG is in any state other than contactPending or active, the local Control Point will be unknown and the size of this string will be zero.
Cisco Channel Interface Processor Transmission Groups Llc Operation Remote Control Point
cipTgLlcOperRemoteCP 1.3.6.1.4.1.9.9.73.1.1.2.1.4 (defined in CISCO-CIPTG-MIB)
The remote control point name for the remote node connected to this TG. The name is extracted from the XID3s received from the remote network node and sent to the host. While the LLC TG is in any state other than contactPending or active, the remote Control Point will be unknown and the size of this string will be zero.
cisco Data Link Switching T Connection Operation Control Unit Rex Sents
ciscoDlswTConnOperCURexSents 1.3.6.1.4.1.9.10.9.1.2.3.1.27 (defined in CISCO-DLSW-MIB)
The number of CanUReach_ex messages sent on this transport connection.
cisco Data Link Switching T Connection Operation Control Unit Rex Rcvds
ciscoDlswTConnOperCURexRcvds 1.3.6.1.4.1.9.10.9.1.2.3.1.29 (defined in CISCO-DLSW-MIB)
The number of CanUReach_ex messages received on this transport connection.
Cisco Entity Field Replaceable Unit Control Power Redundancy Operation Mode
cefcPowerRedundancyOperMode 1.3.6.1.4.1.9.9.117.1.1.1.1.5 (defined in CISCO-ENTITY-FRU-CONTROL-MIB)
The power supply redundancy operational mode.
Cisco Entity Field Replaceable Unit Control Fan Tray Operation Status
cefcFanTrayOperStatus 1.3.6.1.4.1.9.9.117.1.4.1.1.1 (defined in CISCO-ENTITY-FRU-CONTROL-MIB)
The operational state of the fan or fan tray. unknown(1) - unknown. up(2) - powered on. down(3) - powered down. warning(4) - partial failure, needs replacement as soon as possible.
Cisco Entity Field Replaceable Unit Control MIB Power Operation Mode Group
cefcMIBPowerOperModeGroup 1.3.6.1.4.1.9.9.117.3.2.12 (defined in CISCO-ENTITY-FRU-CONTROL-MIB)
The collection of objects which are used to monitor the device's power supply operational redundancy mode.
Cisco Feature Control Operation Status
cfcFeatureCtrlOpStatus 1.3.6.1.4.1.9.9.377.1.1.1.1.7 (defined in CISCO-FEATURE-CONTROL-MIB)
The current operating status of the feature.
Cisco Feature Control Operation Status Reason
cfcFeatureCtrlOpStatusReason 1.3.6.1.4.1.9.9.377.1.1.1.1.8 (defined in CISCO-FEATURE-CONTROL-MIB)
The reason description for the current operating status (represented by the value of corresponding instance of 'cfcFeatureCtrlOpStatus') of the feature. The reason for the current operating status of the feature could be other than explicit user triggered action on the feature.

MIBs list