The objects described here can be monitored with the IPHost Network Monitor.
You can start SNMP monitoring using free 30-day trial version of IPHost right now.
OID list for blocked port
- Sys Bridge Port Receive Blocked Discards
- a3ComSysBridgePortReceiveBlockedDiscards 1.3.6.1.4.1.43.29.4.10.3.1.7 (defined in A3COM-SWITCHING-SYSTEMS-BRIDGE-MIB)
The number of frames discarded by the bridge port identified by this entry because the receiving bridge port was not in the 'forwarding' state. - Sys Bridge Port Transmit Blocked Discards
- a3ComSysBridgePortTransmitBlockedDiscards 1.3.6.1.4.1.43.29.4.10.3.1.15 (defined in A3COM-SWITCHING-SYSTEMS-BRIDGE-MIB)
The number of frames discarded by the bridge port identified by this entry because the transmitting bridge port was not in the 'forwarding' state. - Sys Bridge Port Receive Blocked Discards
- a3ComSysBridgePortReceiveBlockedDiscards 1.3.6.1.4.1.43.29.4.10.3.1.7 (defined in A3COM-SWITCHING-SYSTEMS-MIB)
The number of frames discarded by the bridge port identified by this entry because the receiving bridge port was not in the 'forwarding' state. - Sys Bridge Port Transmit Blocked Discards
- a3ComSysBridgePortTransmitBlockedDiscards 1.3.6.1.4.1.43.29.4.10.3.1.15 (defined in A3COM-SWITCHING-SYSTEMS-MIB)
The number of frames discarded by the bridge port identified by this entry because the transmitting bridge port was not in the 'forwarding' state. - packet Blocked WAN Port
- packetBlockedWANPort 1.3.6.1.4.1.890.1.6.11.2.5.2 (defined in ZYXEL-ZYWALLIDP10-MIB)
Counter for WAN port about blocked packets. - packet Blocked LAN Port
- packetBlockedLANPort 1.3.6.1.4.1.890.1.6.11.2.5.5 (defined in ZYXEL-ZYWALLIDP10-MIB)
Counter for LAN port about blocked packets. - port X25 Admin Blocked Flag
- portX25AdminBlockedFlag 1.3.6.1.4.1.173.7.3.1.5.1.1 (defined in netlink-specific-mib)
A flag which when set, means the port should not be enabled after a boot-up of the node. - port Bsci Admin Blocked Flag
- portBsciAdminBlockedFlag 1.3.6.1.4.1.173.7.3.4.1.1.1 (defined in netlink-specific-mib)
Causes the port to be enabled or disabled at node IPL. - port T1 Admin Blocked Port Flag
- portT1AdminBlockedPortFlag 1.3.6.1.4.1.173.7.3.7.1.1.1 (defined in netlink-specific-mib)
::= { portT1AdminEntry 1 } SYNTAX INTEGER { no(1), yes(2) } ACCESS read-write STATUS mandatory DESCRIPTION " - port Voice Admin Blocked Flag
- portVoiceAdminBlockedFlag 1.3.6.1.4.1.173.7.3.8.1.1.3 (defined in netlink-specific-mib)
The flag which causes the port to be enabled or disabled at node IPL. The port will remain in that state until this flag is changed and the node is rebooted, or until an on- line enable or disable is performed. - Net Link If Llc2 Frame Relay Blocked Port Flag
- nlIfLlc2FrBlockedPortFlag 1.3.6.1.4.1.173.7.4.2.2.1.12 (defined in netlink-specific-mib)
The blocked port flag. - ipx Interface Blocked Port Flag
- ipxInterfaceBlockedPortFlag 1.3.6.1.4.1.173.7.4.3.2.6.1.2 (defined in netlink-specific-mib)
will remain in that state until this parameter is changed - Cisco Blocked Serial Tunneling Port Entry
- bstunPortEntry 1.3.6.1.4.1.9.9.35.1.3.1.1 (defined in CISCO-BSTUN-MIB)
Status and parameter values for a BSTUN port. - Cisco Blocked Serial Tunneling Port Group Number
- bstunPortGroupNumber 1.3.6.1.4.1.9.9.35.1.3.1.1.1 (defined in CISCO-BSTUN-MIB)
The group number to which the bstun port belongs. Frames will only be routed to other ports (on this or another router) in the same bstun group. This group should match a bstunGroupIndex in the bstunGroupTable. - Cisco Blocked Serial Tunneling Port Default Peer Type
- bstunPortDefaultPeerType 1.3.6.1.4.1.9.9.35.1.3.1.1.2 (defined in CISCO-BSTUN-MIB)
The type of identification of the remote default partner. (This is as configured with the 'route all' command.) If ip then the value is in bstunPortDefaultPeerIP; if serial or serialDirect then the value is in bstunPortDefaultPeerSerial. - Cisco Blocked Serial Tunneling Port Default Peer IP
- bstunPortDefaultPeerIP 1.3.6.1.4.1.9.9.35.1.3.1.1.3 (defined in CISCO-BSTUN-MIB)
The ip address of the remote default BSTUN partner, for unrecognized addresses. 0.0.0.0 if partner address type is not ip. - Cisco Blocked Serial Tunneling Port Default Peer Serial
- bstunPortDefaultPeerSerial 1.3.6.1.4.1.9.9.35.1.3.1.1.4 (defined in CISCO-BSTUN-MIB)
If bstunRouteType is serial then this is the serial interface index of the point-to-point link to the remote partner; if bstunRouteType is serialDirect then the partner is in the local BSTUN. if bstunRouteType is ip then this field is 0. - Cisco Blocked Serial Tunneling Port Group
- bstunPortGroup 1.3.6.1.4.1.9.9.35.3.2.3 (defined in CISCO-BSTUN-MIB)
A collection of objects providing information about BSTUN enabled interfaces.
