The objects described here can be monitored with the IPHost Network Monitor.
You can start SNMP monitoring using free 30-day trial version of IPHost right now.
OID list for port traffic
- dot1d Port Number Traffic Classes
- dot1dPortNumTrafficClasses 1.3.6.1.2.1.17.6.1.2.1.1.2 (defined in P-BRIDGE-MIB)
The number of egress traffic classes supported on this port. This object may optionally be read-only. - traffic WAN Port In
- trafficWANPortIn 1.3.6.1.4.1.890.1.6.11.2.3.1 (defined in ZYXEL-ZYWALLIDP10-MIB)
Current traffic in for WAN port. - traffic WAN Port Out
- trafficWANPortOut 1.3.6.1.4.1.890.1.6.11.2.3.2 (defined in ZYXEL-ZYWALLIDP10-MIB)
Current traffic out for WAN port. - traffic LAN Port In
- trafficLANPortIn 1.3.6.1.4.1.890.1.6.11.2.3.3 (defined in ZYXEL-ZYWALLIDP10-MIB)
Current traffic in for LAN port. - traffic LAN Port Out
- trafficLANPortOut 1.3.6.1.4.1.890.1.6.11.2.3.4 (defined in ZYXEL-ZYWALLIDP10-MIB)
Current traffic out for LAN port. - traffic MGMT Port In
- trafficMGMTPortIn 1.3.6.1.4.1.890.1.6.11.2.3.5 (defined in ZYXEL-ZYWALLIDP10-MIB)
Current traffic in for MGMT port. - traffic MGMT Port Out
- trafficMGMTPortOut 1.3.6.1.4.1.890.1.6.11.2.3.6 (defined in ZYXEL-ZYWALLIDP10-MIB)
Current traffic out for MGMT port. - Xylan ATM Traffic Shaper Configuration Port Index
- xylnatmTrafficShaperConfPortIndex 1.3.6.1.4.1.800.2.9.1.18.1.1.2 (defined in XYLAN-CSM-MIB)
The port on which traffic shaping circuitry resides. A CSM-AB module can have either one or two traffic shaping ports. If the module has one traffic shaping port, then the traffic shaping circuitry is always installed on the first port of the module. - Xylan ATM Traffic Shaper Member Port Index
- xylnatmTrafficShaperMemPortIndex 1.3.6.1.4.1.800.2.9.1.19.1.1.2 (defined in XYLAN-CSM-MIB)
The port on which traffic shaping circuitry resides. A CSM-AB module can have either one or two traffic shaping ports. If the module has one traffic shaping port, then the traffic shaping circuitry is always installed on the first port of the module. - port Traffic Enable
- portTrafficEnable 1.3.6.1.4.1.43.1.12.3.1.1.6.5.3.1.1 (defined in irm3-mib)
Enable the sending of port level traffic traps for this port. - port Traffic Threshold
- portTrafficThreshold 1.3.6.1.4.1.43.1.12.3.1.1.6.5.3.1.2 (defined in irm3-mib)
The threshold of packets within the Devicetimebase that will cause a traffic alarm. - port Traffic Port Disable
- portTrafficPortDisable 1.3.6.1.4.1.43.1.12.3.1.1.6.5.3.1.3 (defined in irm3-mib)
Permit a port to be disabled on a traffic threshold alarm. - port Traffic Enable
- portTrafficEnable 1.3.6.1.4.1.43.1.12.3.1.1.6.5.3.1.1 (defined in repeater-mib-2)
Enable or disable the checking for port level traffic thresholds getting exceeded. - port Traffic Threshold
- portTrafficThreshold 1.3.6.1.4.1.43.1.12.3.1.1.6.5.3.1.2 (defined in repeater-mib-2)
The number of packets detected by the specified port within the device timebase that will cause a port traffic alarm trap to be sent. The minimum is 0. There isn't a maximum. - port Traffic Port Disable
- portTrafficPortDisable 1.3.6.1.4.1.43.1.12.3.1.1.6.5.3.1.3 (defined in repeater-mib-2)
Permits a port to be disabled on a traffic threshold getting exceeded. - Repeater Port Group Alarm Traffic Enable
- rptrPortGrpAlarmTrafEnable 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.2 (defined in repeater-rev4-mib)
Get returns whether traffic alarms are enabled/disabled. Set allows for enabling/disabling of traffic alarms. - Repeater Port Group Alarm Traffic Threshold
- rptrPortGrpAlarmTrafThreshold 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.3 (defined in repeater-rev4-mib)
The maximum number of packets that will be allowed before an alarm is generated. - Repeater Port Group Alarm Traffic Group Disable
- rptrPortGrpAlarmTrafGrpDisable 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.4 (defined in repeater-rev4-mib)
Set will permit a port group to be disabled on a traffic alarm condition. Get will show whether the port group disabling is allowed or not. - Repeater Port Alarm Traffic Enable
- rptrPortAlarmTrafEnable 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.3 (defined in repeater-rev4-mib)
Get returns whether traffic alarms are enabled/disabled. Set allows for enabling/disabling of traffic alarms. - Repeater Port Alarm Traffic Threshold
- rptrPortAlarmTrafThreshold 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.4 (defined in repeater-rev4-mib)
The maximum number of packets that will be allowed before an alarm is generated. - Repeater Port Alarm Traffic Port Disable
- rptrPortAlarmTrafPortDisable 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.5 (defined in repeater-rev4-mib)
Set will permit a port to be disabled on a traffic alarm condition. Get will show whether the port disabling is allowed or not.
