The objects described here can be monitored with the IPHost Network Monitor.
You can start SNMP monitoring using free 30-day trial version of IPHost right now.
OID list for port speed
- Sys Token Ring Port Speed
- a3ComSysTokenRingPortSpeed 1.3.6.1.4.1.43.29.4.13.2.1.7 (defined in A3COM-SWITCHING-SYSTEMS-MIB)
The current speed of the port. The default speed is sixteenMegabit. - a3 Com Sys Token Ring Port Speed
- a3ComSysTokenRingPortSpeed 1.3.6.1.4.1.43.29.4.13.2.1.7 (defined in A3COM-SWITCHING-SYSTEMS-TOKEN-RING-MIB)
The current speed of the port. The default speed is sixteenMegabit. - tsm Admin Port Ring Speed
- tsmAdminPortRingSpeed 1.3.6.1.4.1.800.2.19.1.1.1.1.7 (defined in TSMEXT-MIB)
The configured ring speed of the port. 1 = auto. Automatically set the port's ring speed. 2 = fourMegabit. Always set the port's ring speed at four megabits. 3 = sixteenMegabit. Always set the port's ring speed at sixteen megabits. This object may ONLY be set if the value of port's tsmAdminPortConfigType is fixed(1). - tsm Operation Port Ring Speed
- tsmOperPortRingSpeed 1.3.6.1.4.1.800.2.19.1.2.1.1.7 (defined in TSMEXT-MIB)
The operational ring speed of the port. 1 = auto. The port has not yet automatically set the ring speed. 2 = fourMegabit. 3 = sixteenMegabit. - rs232 Port In Speed
- rs232PortInSpeed 1.3.6.1.2.1.10.33.2.1.5 (defined in rfc1317)
The port's input speed in bits per second. - rs232 Port Out Speed
- rs232PortOutSpeed 1.3.6.1.2.1.10.33.2.1.6 (defined in rfc1317)
The port's output speed in bits per second. - rs232 Port In Speed
- rs232PortInSpeed 1.3.6.1.2.1.10.33.2.1.5 (defined in rfc1659)
The port's input speed in bits per second. Note that non-standard values, such as 9612, are probably not allowed on most implementations. - rs232 Port Out Speed
- rs232PortOutSpeed 1.3.6.1.2.1.10.33.2.1.6 (defined in rfc1659)
The port's output speed in bits per second. Note that non-standard values, such as 9612, are probably not allowed on most implementations. - els100 Port Speed
- els100PortSpeed 1.3.6.1.4.1.52.1011.2.1.8 (defined in ctels100-ng-mib)
The speed the port is operating at: 10Mbps, or 100Mbps, or 1000Mbps. - Cabletron DDS Port In Speed
- ctDDSPortInSpeed 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.8 (defined in ctron-remote-access-mib)
This variable describes the current operational receive speed of DDS line. It is a read only value based entirely on DDS type (CC or PRI). - Cabletron DDS Port Out Speed
- ctDDSPortOutSpeed 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.9 (defined in ctron-remote-access-mib)
This variable describes the current operational transmit speed of DDS line. It is a read only value based entirely on DDS type CC or PRI - dds Port In Speed
- ddsPortInSpeed 1.3.6.1.4.1.52.4.1.2.7.1.5.1.1.8 (defined in ctron-wan-mib)
This variable describes the current operational receive speed of DDS line. It is a read only value based entirely on DDS type (CC or PRI). - dds Port Out Speed
- ddsPortOutSpeed 1.3.6.1.4.1.52.4.1.2.7.1.5.1.1.9 (defined in ctron-wan-mib)
This variable describes the current operational transmit speed of DDS line. It is a read only value based entirely on DDS type CC or PRI - Token Ring Port Group Speed
- tRingPortGrpSpeed 1.3.6.1.4.1.52.4.1.2.1.1.2.1.1.10 (defined in dot5-log-mib)
This object sets the speed of the board. On devices with a MAC interface this object is read-only, and will return NO SUCH NAME on write requests. - Token Ring Port Management Speed Fault Detect
- tRingPortMgmtSpeedFaultDetect 1.3.6.1.4.1.52.4.1.2.1.1.3.1.1.1.7 (defined in dot5-log-mib)
This object indicates whether a speed fault has been detected at this port. If the HW is incapable of detecting a speed fault at the port, the value notDetectable is returned. - dot5 Physical Management Port Common Speed Fault Detect
- dot5PhysMgmtPortCommonSpeedFaultDetect 1.3.6.1.4.1.52.4.1.1.6.1.3.1.1.1.7 (defined in dot5-phys-mib)
This object indicates whether a speed fault has been detected at this token ring port. If the HW is incapable of detecting a speed fault at the port, the value notDetectable is returned. - port Link Speed
- portLinkSpeed 1.3.6.1.4.1.52.259.10.3.2.4.1.1.3 (defined in elh100-mib)
The speed at which the port is currently operating. If there is no link on the port, this object returns noLink(1). - port Speed Config
- portSpeedConfig 1.3.6.1.4.1.52.259.10.3.2.4.1.1.4 (defined in elh100-mib)
Selects the speed at which the port operates. The factory setting is autoNegotiate(1). - switch Port Speed
- switchPortSpeed 1.3.6.1.4.1.52.259.10.3.4.1.1.1.4 (defined in elh100-mib)
The speed at which the switch port is currently operating. If the port is inactive (port 2 on media modules and port 3 on internal switch modules), noLink(1) is returned. - Switch Port Management Speed Dpx Admin
- swPortMgtSpeedDpxAdmin 1.3.6.1.4.1.52.3.9.1.10.7.2.1.1.3 (defined in els100-s24tx2m-mib)
Set the port speed and duplex mode as follows: halfDuplex10(1) - 10Mbps and half duplex mode fullDuplex10(2) - 10Mbps and full duplex mode halfDuplex100(3) - 100Mbps and half duplex mode fullDuplex100(4) - 100Mbps and full duplex mode halfDuplex1000(5) - 1000Mbps and half duplex mode fullDuplex1000(6) - 1000Mbps and full duplex mode autoNegotiation(7) - let the switch to negotiate with the other end of connection. hundredBaseTX port can be set as halfDuplex10(1) fullDuplex10(2) halfDuplex100(3) fullDuplex100(4) autoNegotiation(7) hundredBaseFX port can be set as halfDuplex100(3) fullDuplex100(4) thousandBaseSX port can be set as halfDuplex1000(5) fullDuplex1000(6) autoNegotiation(7) The actual operating speed and duplex of the port is given by swPortMgtSpeedDpxInUse. - Switch Port Management Speed Dpx In Use
- swPortMgtSpeedDpxInUse 1.3.6.1.4.1.52.3.9.1.10.7.2.1.1.4 (defined in els100-s24tx2m-mib)
The operating speed and duplex mode of the switched port. - port Physical X25 Operation Speed
- portPhyX25OperSpeed 1.3.6.1.4.1.173.7.3.1.2.1.2 (defined in netlink-specific-mib)
This object defines the speed of the X25 port. The speed may only be set to one of a series of reasonable values, and if an attempt is made to set the speed to a value which is within the valid range but not equal to one of these values, the speed will be rounded up. If the connector type of the port is RS232, the port could be a standard port or a high speed port. If the port is a high speed RS232 port, the maximum valid speed is 256000. If the port is a standard RS232 port, the maximum valid speed is 64000 on the FRX4000/SS1840 and 19200 on all other products. It may be possible to set the speed of a standard RS232 port to a speed which is valid for a high speed RS232 port but invalid for a standard RS232 port. In this case, the port may not end up having the invalid speed. The default speed for a standard RS232 port on the FRX6000 is 19200. - port Bsci Operation Speed
- portBsciOperSpeed 1.3.6.1.4.1.173.7.3.4.2.1.3 (defined in netlink-specific-mib)
Data transmission rate in bits per second. - port Voice Admin Speed
- portVoiceAdminSpeed 1.3.6.1.4.1.173.7.3.8.1.1.4 (defined in netlink-specific-mib)
The speed of the port which is transmitted as part of a Call Setup frame. A Voice call will be established if there is enough bandwidth at each end to provide the minimum configured rate. - port Speed Dpx Configuration
- portSpeedDpxCfg 1.3.6.1.4.1.52.4.12.30.1.2.1.1.4 (defined in v2h124-24-mib)
according to: halfDuplex10(2) - 10Mbps and half duplex mode fullDuplex10(3) - 10Mbps and full duplex mode halfDuplex100(4) - 100Mbps and half duplex mode fullDuplex100(5) - 100Mbps and full duplex mode halfDuplex1000(6) - 1000Mbps and half duplex mode fullDuplex1000(7) - 1000Mbps and full duplex mode hundredBaseTX port can be set as halfDuplex10(2) fullDuplex10(3) halfDuplex100(4) fullDuplex100(5) hundredBaseFX port can be set as halfDuplex100(4) fullDuplex100(5) thousandBaseSX port can be set as halfDuplex1000(6) fullDuplex1000(7) The actual operating speed and duplex of the port is given by portSpeedDpxStatus. - port Speed Dpx Status
- portSpeedDpxStatus 1.3.6.1.4.1.52.4.12.30.1.2.1.1.8 (defined in v2h124-24-mib)
switched port or trunk. If the entry represents a trunk, the speed is that of its individual members unless the member ports have been inconsistently configured in which case the value is error(1). - agent Lag Detailed Port Speed
- agentLagDetailedPortSpeed 1.3.6.1.4.1.14179.1.2.2.3.1.22 (defined in AIRESPACE-SWITCHING-MIB)
Lag port speed. See agentPortType for description and list of valid values. - Cisco 90i D Port Speed
- frxDPortSpeed 1.3.6.1.4.1.1570.1.2.9 (defined in CISCO-90-MIB)
System Default for frxPortSpeed - used when the Download Configuration pushbutton on the channel unit faceplate is pushed and when frxDefaultEnable is set to 1. This is the speed that the channel unit port runs at. 1=56kbps 2=64kbps 3=128kbps 4=144kbps - Cisco 90i Port Speed
- frxPortSpeed 1.3.6.1.4.1.1570.1.6.1.1.1 (defined in CISCO-90-MIB)
This is the speed that the channel unit port runs at. 1=56kbps 2=64kbps 3=128kbps 4=144kbps This parameter can only be changed if frxConfigSrc is set to SNMP. - Cisco 2900 Port Admin Speed
- c2900PortAdminSpeed 1.3.6.1.4.1.9.9.87.1.4.1.1.33 (defined in CISCO-C2900-MIB)
The object controls the speed of the port. The current operational speed of the port can be determined from ifSpeed. - Cisco Network Office Switch Port Speed Admin
- cnosPortSpeedAdmin 1.3.6.1.4.1.9.10.43.1.3.1.1.5 (defined in CISCO-CNO-SWITCH-MIB)
Set to tenMbps(1) to operate in 10Mbps speed mode. Set to oneHundredMbps(2) to operate in 100Mbps speed mode. Set to autoNegotiate(3) to allow the switch to negotiate with the other end of the connection. - Cisco Network Office Switch Port Speed Status
- cnosPortSpeedStatus 1.3.6.1.4.1.9.10.43.1.3.1.1.6 (defined in CISCO-CNO-SWITCH-MIB)
The operating speed of the switched port.
