aRtgPnniRfTxTdpTable - a Rtg Pnni Rf Tx Tdp Table

MIBs list

With IPHost Network Monitor you can run simple snmp requests against a Nortel device in your network.

aRtgPnniRfTxTdpTable

a Rtg Pnni Rf Tx Tdp Table

This attribute is a vector of five traffic parameters whose meanings are defined by the txTrafficDescType attribute. The values of peak cell rate (PCR), sustained cell rate (SCR) and requested shaping rate are expressed in cell/s. Maximum burst size (MBS) is expressed in cells. CDVT is expressed in microseconds. The values of PCR, SCR, MBS and CDVT are used for connection admission control (CAC). The value of CDVT is only used for connections where the atmServiceCategory is constantBitRate. For all other values of atmServiceCategory, CDVT is ignored. The values of PCR, SCR and requested shaping rate are used to determine the actual shaping rate where traffic shaping is enabled. When txTrafficDescType is 1 or 2, all of the parameters must be set to zero. When txTrafficDescType is 3, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameter 1 must be non-zero. Parameters 2 and 3 must be zero. When txTrafficDescType is 4, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic with cell discard; parameter 2 represents the PCR for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameter 1 must be greater than or equal to parameter 2. Parameters 1 and 2 must be non-zero. Parameter 3 must be zero. When txTrafficDescType is 5, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic with cell tagging; parameter 2 represents the PCR for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameter 1 must be greater than or equal to parameter 2. Parameters 1 and 2 must be non-zero. Parameter 3 must be zero. When txTrafficDescType is 6, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 and 1 traffic; parameter 3 represents the MBS for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2 and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5, must either be zero (unused) or greater than or equal to parameter 2. When txTrafficDescType is 7, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 with cell discard; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2 and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5, must either be zero (unused) or greater than or equal to parameter 2. When txTrafficDescType is 8, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 traffic with cell tagging; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2 and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5, must either be zero (unused) or greater than or equal to parameter 2. Whenever it is valid for PCR to be specified, parameter 5 may also be used to specify a requested shaping rate. A non-zero value in parameter 5 overrides the value in parameter 1 and is used as the peak cell rate in calculations of CAC and shaping rate. For txTrafficDescType 3, 4 and 5, the transmit traffic will be shaped at the next rate less than the PCR. For txTrafficDescType 6, 7 and 8, the transmit traffic will be shaped at the highest available rate which is between PCR and SCR. However, if there is no available shaping rate between PCR and SCR, traffic will be shaped at the next rate above the PCR.

Back to Nortel-Magellan-Passport-AtmNetworkingMIB MIB page.

IPHost Network monitor allows you to monitor aRtgPnniRfTxTdpTable on Allied Telesis device via the SNMP protocol. Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring Nortel speech servers right now.

Easy monitoring of aRtgPnniRfTxTdpTable with IPHost tools

MIBs list