frConnServiceType - fr Connection Service Type - CISCO-WAN-FR-CONN-MIB

MIBs list

With IPHost Network Monitor you can run simple snmp requests against a Cisco device in your network.

frConnServiceType

fr Connection Service Type
1.3.6.1.4.1.351.110.5.1.2.1.1.1.43

This specifies the service type 1 ==> Constant Bit Rate 2 ==> Variable Bit Rate 3 ==> Not used 4 ==> Unspecified Bit Rate 5 ==> ATM frame relay 6 ==> standard ABR 7 ==> foresight ABR Note that this is used by PXM card, SV+ doesn't need to set it, if not set in the connection setup request, it'll be defaulted to ATFR type for FRSM. Also to make it compatible with existing AUSM MIB definition, value 3 is not used. The following types are being added for PNNI support. and are based on UNI 4.0 cbr1 (21) - CBR.1 vbr1rt (22) - Real time VBR.1 vbr2rt (23) - Real time VBR.2 vbr3rt (24) - Real time VBR.3 vbr1nrt(25) - Non Real time VBR.1 vbr2nrt(26) - Non Real time VBR.2 vbr3nrt(27) - Non Real time VBR.3 ubr1 (28) - UBR.1 ubr2 (29) - UBR.2 stdabr (30) - TM 4.0 compliant standard ABR cbr2 (31) - CBR.2 cbr3 (32) - CBR.3 For FRSM12 Card: Not Supported. Derived from chanServType. DEFVAL {atfr} ::= { frChanCnfGrpEntry 43 } SYNTAX Integer32 (1..15) MAX-ACCESS read-write STATUS current DESCRIPTION This is used by PXM to determine how important this connection is when selecting connections to route DEFVAL {1} ::= { frChanCnfGrpEntry 44 } SYNTAX Integer32 (1..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION The value of this object specifies the Maximum allowed cost. It is related to Cost Based Routing. This is used by PXM so that it won't choose a path with a cost greater than this configured level. This is not necessary to be provided in the connection setup request, if not provided, the default value 255 will be used. Also the range supported depends upon the controller configured : Controller Range Default Value chanFrConnType = par(2) 1..65535 255 chanFrConnType = pnni(5) 1..2147483647 2147483647. ::= { frChanCnfGrpEntry 45 } SYNTAX INTEGER { norestriction (1), terrestrialTrunk (2), sateliteTrunk (3) } MAX-ACCESS read-write STATUS current DESCRIPTION Restricted trunk type for routing, used by PXM. It specifies that the connection either cannot be routed over satelite trunks, or terrestrial trunks, or it can be on any type of trunk. It is not necessary to be provide in the connection setup request, the default value is norestriction(1). For FRSM12 Card: Not Supported DEFVAL {norestriction} ::= { frChanCnfGrpEntry 46 } SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION The value of this object identifies the PCR(Peak Cell Rate). If not provided in the connection setup request, it'll be derived from object 'pir'. For FRSM12 Card: Default value is (1.44 * CIR) ::= { frChanCnfGrpEntry 47 } SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION Peak cell rate of the other end, if not set, will be set to the same as local end PCR (frConnPCR). However, note that if the CIRs for both local and remote end are set to the different value (i.e., asymmetric conn), then this should be set differently from local end PCR. For FRSM12 Card: Default value is frConnPCR ::= { frChanCnfGrpEntry 48 } SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION Minimum cell rate, if not provided in the connection setup request, it'll be derived from object 'mir'. For FRSM12 Card: Default value is frConnPCR ::= { frChanCnfGrpEntry 49 } SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION Minimum cell rate of the other end, if not set, will be set to the same as local end MCR (frConnMCR). However, note that if the CIRs for both local and remote end are set to the different value (i.e., asymmetric conn), then this should be set differently from local end MCR. For FRSM12 Card: Default value is frConnMCR ::= { frChanCnfGrpEntry 50 } SYNTAX Integer32 (0..100) MAX-ACCESS read-write STATUS current DESCRIPTION This is the expected long-term utilization of the channel by this end-point. If this is not specified in the connection setup request, it'll be defaulted to 100 percent For FRSM12 Card: Not Supported DEFVAL {100} ::= {frChanCnfGrpEntry 51 } SYNTAX Integer32 (0..100) MAX-ACCESS read-write STATUS current DESCRIPTION This is the expected long-term utilization of the channel by the other end-point. If this is not specified in the connection setup request, it'll be set to be the same as the local end frConnPercentUtil value assuming that the connection is symmetric. In a asymmetric connection, this object is supposed to be set. For FRSM12 Card: Not Supported.

Back to CISCO-WAN-FR-CONN-MIB MIB page.

IPHost Network monitor allows you to monitor frConnServiceType on Cisco device via the SNMP protocol. Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring Cisco firewalls right now.

Easy monitoring of frConnServiceType with IPHost tools

MIBs list