dsx1 Vism Cnf Group Table

1.3.6.1.4.1.351.110.4.3.5.1.1

The VISM specific DS1/E1 configuration table. This table contains the additional VISM configuration information for DS1/E1. ::= { dsx1VismCnfGrp 1 } SYNTAX Dsx1VismCnfGrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION An entry in the VISM Dsx1 Configuration table. An entry is created when a DS1/E1 is added. An entry is deleted when a DS1/E1 is deleted. The DS1/E1 is specify by 'lineEnable' object in CISCO-MGX82XX-DSX1-MIB. INDEX { vismLineNum } ::= { dsx1VismCnfGrpTable 1 } Dsx1VismCnfGrpEntry ::= SEQUENCE { vismLineNum Integer32, vismEcanEnabled INTEGER, vismEcanToneDisable INTEGER, vismEcanCnfNRN INTEGER, vismEcanTail Integer32, vismEcanREC INTEGER, vismCompCnfVAD INTEGER, vismSignalingType INTEGER, vismCcsChannels Integer32, vismCadenceTime Integer32, vismTrunkConditionEnable TruthValue, vismDsx1CircuitIdentifier DisplayString, vismDsx1TxDigitOrder INTEGER, vismDsx1TonePlanRegion DisplayString, vismDsx1TonePlanVersion Integer32, vismDsx1RingingTO Integer32, vismDsx1RingBackTO Integer32, vismDsx1BusyTO Integer32, vismDsx1ReorderTO Integer32, vismDsx1DialTO Integer32, vismDsx1StutterDialTO Integer32, vismDsx1OffHookAlertTO Integer32, vismDsx1RemoteRingback INTEGER, vismDsx1MidcallTpart Integer32, vismDsx1MidcallTcrit Integer32, vismDsx1Sa4Byte Integer32, vismDsx1Sa5Byte Integer32, vismDsx1Sa6Byte Integer32, vismDsx1Sa7Byte Integer32, vismDsx1Sa8Byte Integer32, vismDsx1State INTEGER, vismDsx1AdminStateControl INTEGER, vismBearerBusyCode Integer32, vismDsx1V110Enable TruthValue, vismDsx1AlarmLogEnable TruthValue, vismDsx1AlarmLogAdminTimer Unsigned32, vismDsx1AlarmLogOperTimer Unsigned32, vismDsx1ElectricalSignalEnable TruthValue } SYNTAX Integer32 (1..8) MAX-ACCESS read-only STATUS current DESCRIPTION This object identifies the DS1/E1 interface number. ::= { dsx1VismCnfGrpEntry 1 } SYNTAX INTEGER { disable (1), enable (2) } MAX-ACCESS read-write STATUS current DESCRIPTION This object disable/enable echo cancellation. 'disable' : disable echo cancellation. 'enable' : enable echo cancellation. DEFVAL { enable } ::= { dsx1VismCnfGrpEntry 2 } SYNTAX INTEGER { ignore (1), g-164 (2), reserve (3), g-165 (4) } MAX-ACCESS read-only STATUS deprecated DESCRIPTION This object determines the behavior of the echo canceler in the presence of a modem. 'ignore': Ignore 2100 Hz modem answer tone. 'g-164' : G-164 mode, disable the canceler for all the tones, phase reversing or not. 'reserve': Reserved setting the value to 'reserve(3)' results in BadValue error. 'g-165': G.165 mode, disable the canceler for phase reversing tone only (V.8 modulated phase reversing tone as well as the V.fast non standard phase reversing tone). DEFVAL { g-165 } ::= { dsx1VismCnfGrpEntry 3 } SYNTAX INTEGER { reenableOnModemData (1), reenableOnCallEnd (2) } MAX-ACCESS read-only STATUS deprecated DESCRIPTION Echo canceler re-enable (NRN). This object determines when an echo canceler re-enable and begins cancellation after it has been disabled. 'reenableOnModemData': Re-enable canceler when modem data is gone (low energy). 'reenableOnCallEnd' : Re-enable canceler at end of call, This object is not applicable when vismEcanToneDisable 'ignore'. DEFVAL { reenableOnModemData } ::= { dsx1VismCnfGrpEntry 4 } SYNTAX Integer32 (24..128) UNITS "milliseconds This object identifies the maximum tail. The object should be set just higher than the worst round trip delay anticipated. Convergence times may increase for longer tails and more resource will be used. Only following discrete values are allowed: 24, 32, 48, 64, 80, 96, 112 and 128.