bearer Conn Table

1.3.6.1.4.1.351.110.5.5.9.1

This table describes the statistical information available on a per-bearer connection basis. These values are applicable equally to an endpoint. ::= { bearerConnGrp 1 } SYNTAX BearerConnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION Each entry in this table corresponds to a bearer connection, that was setup by binding an endpoint with a VC(Virtual channel)/CID pair, either through CLI or SNMP. The statistical counters in this table are generic voice quality parameters that are equally applicable in all types of Voice Over Packet adapations (VoIP, VoAAL1 and VoAAL2). However, they are maintained only in the PVC(Permanent virtual circuit) trunking model because, these counters get reset in the switching model on a per call basis. The entries in this table are implicitly created/deleted at the time of creation/deletion of entries in the vismAal2CidCnfTable. INDEX { bearerEndptNum } ::= { bearerConnTable 1 } BearerConnEntry ::= SEQUENCE { bearerEndptNum Integer32, bearerCid Integer32, bearerLcn Integer32, bearerSentPkts Counter32, bearerRcvdPkts Counter32, bearerSentOctets Counter32, bearerRcvdOctets Counter32, bearerLostPkts Counter32, bearerJitter Integer32, bearerLatency Integer32, bearerAal2ExtAISCnts Counter32, bearerAal2ExtRAICnts Counter32, bearerAal2ConnAISCnts Counter32, bearerAal2ConnRDICnts Counter32, bearerCntClrButton INTEGER, bearerPeakXmtCellRate Unsigned32, bearerCurrentXmtCellRate Unsigned32, bearerPeakRcvCellRate Unsigned32, bearerCurrentRcvCellRate Unsigned32, bearerCurrentExtAISRcvCnts Counter32, bearerCurrentExtRAIRcvCnts Counter32, bearerCurrentConnAISCnts Counter32, bearerCurrentConnRDICnts Counter32, bearerCurrentExtAISXmtCnts Counter32, bearerCurrentExtRAIXmtCnts Counter32 } SYNTAX Integer32(1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION This attribute defines the index for the Bearer Connection Table. This refers to the same value as the index to the mgEndpointTable ie. mgEndpointNumber. This is define in CISCO-WAN-MG-MIB MIB. ::= { bearerConnEntry 1 } SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION This attribute defines the CID associated with this bearer connection. This refers to the same value as vismAal2CidNum in the vismAal2CidCnfTable. ::= { bearerConnEntry 2 } SYNTAX Integer32(131..510) MAX-ACCESS read-only STATUS current DESCRIPTION This attribute defines the PVC or LCN(Logical Channel Number) number to which this bearer connection is associated with. This refers to the same value as in vismCnfChanNum in vismChanCnfGrp table. This is define in CISCO-VISM-CONN-MIB MIB. ::= { bearerConnEntry 3 } SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION This attribute defines the count of packets sent towards the network since this connection setup. ::= { bearerConnEntry 4 } SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION This attribute defines the count of packets received from the network since this connection setup. ::= { bearerConnEntry 5 } SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION This attribute defines the count of bytes sent towards the network since this connection setup. ::= { bearerConnEntry 6 } SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION This attribute defines the count of bytes received from the network since this connection setup. ::= { bearerConnEntry 7 } SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION This attribute defines the count of packets lost in the egress direction (from the network). This is a computed number based on the expected number of packets and the actual number of packets arrived from the network. ::= { bearerConnEntry 8 } SYNTAX Integer32 UNITS "milliseconds This attribute defines the jitter (a.k.a interarrival jitter) This value is determined by the DSP(Digital Signal Processing) and obtained by the HOST processor upon querying the DSP on a periodic basis. ::= { bearerConnEntry 9 } SYNTAX Integer32 UNITS "milliseconds This attribute defines the latency (a.k.a end-to-end average transmission delay for a voice packet). ::= { bearerConnEntry 10 } SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION This object contains the number of external AIS (Alarm Indication Signal) AAL2 Type3 packets received. External AIS - is associated with a maintenance alarm detected on a defective maintenance span, that is transmitted in the direction of the defect as a substitute for normal signal. The purpose is to show the downstream entities that a defect has been identified and to prevent other maintenance alrams consequent to this first defect. External AIS bit stream is represented by an all 1's signal. REFERENCE ITU-T Rec. M.20 sec. 5.4.2 a