Cisco CAS If Ext Voice Configuration Cas Profile

1.3.6.1.4.1.9.9.314.1.1.1.1.22

This object specifies the index of CAS profile that is used by this DS0 group. The value of this object is ccasProfileIndex in ccasIfExtProfileTable. This object is applicable only when the DS0 group is in a DS1 line whose signal mode is configured for CAS signaling, which means the dsx1SignalMode of the DS1 line is set to 'robbedBit(2)' for T1, or 'bitOriented(3)' for E1. If the DS1 is not configured for CAS and if the CAS profile index, ccasIfExtDs0GrpCasProfile is specified, the set operation will be rejected, and if it were not specified, it will default to a value 0. When the DS1 line is configured for CAS signaling, all the DS0 channels (ccasGrpCfgDs0Channels) in the DS1 line must be in one and only one DS0 group. If the DS1 is configured for CAS and if the CAS profile index, ccasIfExtDs0GrpCasProfile is not specified, the default CAS profile is 1. ::= { ccasIfExtVoiceCfgEntry 22 } SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION This object specifies the index of CAS variant that is used by this DS0 group. The value of this object is the same as the value of ccasVariantIndex in ccasIfExtVariantTable. This object is applicable only when the DS0 group is in a DS1 line whose signal mode is configured for CAS signaling, which means the dsx1SignalMode of the DS1 line is set to 'robbedBit(2)' for T1, or 'bitOriented(3)' for E1. When the DS1 line is configured for CAS signaling, all the DS0 channels (ccasGrpCfgDs0Channels) in the DS1 line must be in one and only one DS0 group. It is a mandatory object when DS1 is configured for CAS. If the DS1 is not configured for CAS and ccasIfExtDs0GrpCasVariant is specified, the set operation will be rejected, and it has a default value 0 when it is not specified. ::= { ccasIfExtVoiceCfgEntry 23 } SYNTAX OCTET STRING (SIZE (4)) MAX-ACCESS read-only STATUS current DESCRIPTION This object contains the bit map of the failure DS0 channels in the DS0 group. The MSB (most significant bit) is DS0 channel number 1. For T1, only higher 24 bits are used to specify the the CAS channels for the CAS group. A 1-bit indicates the failure channel in group and a 0-bit indicates it isn't. DEFVAL { '00000000'H } ::= { ccasIfExtVoiceCfgEntry 24 } SYNTAX INTEGER { none (1), simple (2), g711A2 (3) } MAX-ACCESS read-write STATUS current DESCRIPTION This object specifies the type of comfort noise generation: (1) none: No comfort noise generation (2) simple: Cisco Proprietary comfort noise generation (3) g711A2: ITU G.711 Appendix II compliant This object is applicable only if 'ccasVoiceCfgNoiseRegEnable' is set to 'true'. When Voice Activation Detection(VAD) is enabled by setting 'ccasIfExtVoiceCfgVadEnabled' to 'true', 'ccasVoiceCfgNoiseRegEnable' indicates whether or not the background comfort noise should be played to fill the silence gaps. If 'ccasVoiceCfgNoiseRegEnable' is set to 'false', this object contains value 'none(1)'. REFERENCE 1. A comfort noise payload definition for ITU-T G.711 use in packet-based multimedia communication systems, ITU-T G.711 Appendix 2, Februrary, 2000. 2. CISCO-CAS-IF-MIB, ccasVoiceCfgNoiseRegEnable DEFVAL { simple } ::= { ccasIfExtVoiceCfgEntry 25 } -- ********************************************************************* -- Cisco CAS/DS0 Group General Configuration Extended Table -- -- This table contains objects that support bulk provisioning -- -- ********************************************************************* SYNTAX SEQUENCE OF CcasIfExtDs0GrpCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION The voice interface extended table defines the parameters related to the configuration of voice interfaces (DS0 group of DS1). This table extends the ccasVoiceCfgTable. Each table entry describes an instance of a voice interface configuration (DS0 group of DS1) in a media gateway.