UPS2-MIB DEFINITIONS ::= BEGIN -- ctron-ups2-mib.txt The UPS Revision 2 MIB -- Revision: 1.01.00 -- Part Number: -- Date: September 12, 1995 -- Cabletron Systems, Inc. -- 35 Industrial Way, P.O. Box 5005 -- Rochester, NH 03867-0505 -- (603) 332-9400 -- support@ctron.com -- This module provides authoritative definitions for Cabletron's -- enterprise-specific UPS MIB. -- -- This module will be extended, as needed. -- -- Cabletron Systems reserves the right to make changes in -- specification and other information contained in this document -- without prior notice. The reader should consult Cabletron Systems -- to determine whether any such changes have been made. -- -- In no event shall Cabletron Systems be liable for any incidental, -- indirect, special, or consequential damages whatsoever (including -- but not limited to lost profits) arising out of or related to this -- document or the information contained in it, even if Cabletron -- Systems has been advised of, known, or should have known, the -- possibility of such damages. -- -- Cabletron grants vendors, end-users, and other interested parties -- a non-exclusive license to use this Specification in connection -- with the management of Cabletron products. -- Copyright August 95 Cabletron Systems IMPORTS ctUPS FROM CTRON-MIB-NAMES DisplayString FROM RFC1213-MIB OBJECT-TYPE FROM RFC-1212; -- Textual convention -- DisplayString ::= OCTET STRING -- This data type is used to model textual information taken from -- the NVT ASCII character set. By convention, objects with this -- syntax, unless explicitly stated, are declared as having: -- -- SIZE (0..255) --=============== group definitions ==================== upsSystem OBJECT IDENTIFIER ::= { ctUPS 1 } upsId OBJECT IDENTIFIER ::= { ctUPS 2 } upsBattery OBJECT IDENTIFIER ::= { ctUPS 3 } upsInput OBJECT IDENTIFIER ::= { ctUPS 4 } upsOutput OBJECT IDENTIFIER ::= { ctUPS 5 } upsStatus OBJECT IDENTIFIER ::= { ctUPS 6 } upsConfig OBJECT IDENTIFIER ::= { ctUPS 7 } upsExtMeas OBJECT IDENTIFIER ::= { ctUPS 8 } upsAddlFuncs OBJECT IDENTIFIER ::= { ctUPS 9 } --================ upsSystem group ==================== -- UPS System Group -- Implementation of this group is mandatory -- This group covers system-level information on the UPSs available upsNumUPSs OBJECT-TYPE SYNTAX INTEGER (0..2) ACCESS read-only STATUS mandatory DESCRIPTION "The number of UPSs available." ::= { upsSystem 1 } --=============== upsId group ===================== -- UPS Identification Group -- Implementation of this group is mandatory if one or more UPSs -- are to be monitored -- This group covers identification information on the UPSs available upsIdTable OBJECT-TYPE SYNTAX SEQUENCE OF UpsIdEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of identification table entries. The number of entries is given by the value of upsNumUPSs." ::= { upsId 1 } upsIdEntry OBJECT-TYPE SYNTAX UpsIdEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing objects for a particular UPS." INDEX { upsIndex } ::= { upsIdTable 1 } UpsIdEntry ::= SEQUENCE { upsIndex INTEGER, upsName DisplayString, upsModelType INTEGER, upsFwVersion DisplayString, upsSerialNumber DisplayString, upsManufDate DisplayString } upsIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A unique value which identifies a particular UPS." ::= { upsIdEntry 1 } upsName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..8)) ACCESS read-write STATUS mandatory DESCRIPTION "The UPS's name. A maximum of 8 characters may be specified. This object is initialized to the UPS's model name." ::= { upsIdEntry 2 } upsModelType OBJECT-TYPE SYNTAX INTEGER { smartUps250(1), smartUps400(2), smartUps600(3), smartUps900(4), smartUps1250(5), smartUps2000(6), matrixUps3000(7), matrixUps5000(8), other(9) } ACCESS read-only STATUS mandatory DESCRIPTION "The UPS's base model type." ::= { upsIdEntry 3 } upsFwVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(0..8)) ACCESS read-only STATUS mandatory DESCRIPTION "The UPS's firmware version." ::= { upsIdEntry 4 } upsSerialNumber OBJECT-TYPE SYNTAX DisplayString (SIZE(0..16)) ACCESS read-only STATUS mandatory DESCRIPTION "The UPS's serial number as set at the factory." ::= { upsIdEntry 5 } upsManufDate OBJECT-TYPE SYNTAX DisplayString (SIZE(0..8)) ACCESS read-only STATUS mandatory DESCRIPTION "The UPS's date of manufacture in the format mm/dd/yy." ::= { upsIdEntry 6 } --=============== upsBattery group ==================== -- UPS Battery Group -- Implementation of this group is mandatory if one or more UPSs -- are to be monitored -- This group covers information on the Batteries within each UPS upsBatteryTable OBJECT-TYPE SYNTAX SEQUENCE OF UpsBatteryEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of battery table entries. The number of entries is given by the value of upsNumUPSs." ::= { upsBattery 1 } upsBatteryEntry OBJECT-TYPE SYNTAX UpsBatteryEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing objects for a particular UPS." INDEX { upsIndex } ::= { upsBatteryTable 1 } UpsBatteryEntry ::= SEQUENCE { upsBatteryCapacity INTEGER, upsBatteryVoltage INTEGER, upsBatteryTest INTEGER, upsBatteryTestResult INTEGER, upsRunTimeCalibration INTEGER, upsEstimatedRunTimeRemaining INTEGER, upsTransferCause INTEGER, upsBatteryTestTime INTEGER, upsLowBatteryWarning INTEGER } upsBatteryCapacity OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The UPS's remaining battery capacity expressed as a percent of the fully charged condition. The value of this object is the actual percentage * 10 (that is, to determine the actual percentage, divide the value of this object by 10)." ::= { upsBatteryEntry 1 } upsBatteryVoltage OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The UPS's present battery voltage. The value of this object is the actual voltage * 100 (that is, to determine the actual voltage, divide the value of this object by 100)." ::= { upsBatteryEntry 2 } upsBatteryTest OBJECT-TYPE SYNTAX INTEGER { initiateTest(1) } ACCESS read-write STATUS mandatory DESCRIPTION "This object may be written to initiate testing of the UPS's battery packs. Reading this object will always return a 0." ::= { upsBatteryEntry 3 } upsBatteryTestResult OBJECT-TYPE SYNTAX INTEGER { batteryOK(1), batteryBad(2), noRecentTest(3), invalidTestDueToOverload(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The result of the last battery test performed." ::= { upsBatteryEntry 4 } upsRunTimeCalibration OBJECT-TYPE SYNTAX INTEGER { performTest(1), abortTest(2), testInProgress(3), testNotInProgress(4) } ACCESS read-write STATUS mandatory DESCRIPTION "This object may be written to initiate or terminate the test used to calibrate the returned run time value. This test will only run if battery capacity is 100%. Results of this test can be retrieved by upsEstimatedRunTimeRemaining. Valid values for writing are 1 (initiate test) and 2 (terminate test). In addition, this object may be read to determine whether the test is currently running. Valid values for reading are 3 (test is in progress) and 4 (test is not in progress)." ::= { upsBatteryEntry 5 } upsEstimatedRunTimeRemaining OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The UPS's estimated remaining run time in minutes. The UPS may be queried when operating in the on-line, bypass, or on-battery modes of operation. The run time estimate is based on available battery capacity and output load." ::= { upsBatteryEntry 6 } upsTransferCause OBJECT-TYPE SYNTAX INTEGER { noTransfer(1), selfTest(2), inputLineSpike(3), inputLowVoltage(4), inputHighVoltage(5), inputLineFrequencyBad(6) } ACCESS read-only STATUS mandatory DESCRIPTION "The reason for the most recent transfer to on-battery operation." ::= { upsBatteryEntry 7 } upsBatteryTestTime OBJECT-TYPE SYNTAX INTEGER { twoWeeks(1), oneWeek(2), startupOnly(3), off(4) } ACCESS read-write STATUS mandatory DESCRIPTION "The frequency of execution of the UPS's automatic battery test. The test may be run immediately upon startup, upon startup and every 7 days thereafter, upon startup and every 14 days thereafter, or never." DEFVAL { twoWeeks } ::= { upsBatteryEntry 8 } upsLowBatteryWarning OBJECT-TYPE SYNTAX INTEGER { twoMinutes(1), fiveMinutes(2), sevenMinutes(3), tenMinutes(4) } ACCESS read-write STATUS mandatory DESCRIPTION "The interval between activation of the UPS's low battery alarm warnings and shutdown of the UPS." DEFVAL { twoMinutes } ::= { upsBatteryEntry 9 } --=============== upsInput group ==================== -- UPS Input Group -- Implementation of this group is mandatory if one or more UPSs -- are to be monitored -- This group covers information on the AC Inputs to each UPS upsInputTable OBJECT-TYPE SYNTAX SEQUENCE OF UpsInputEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of input table entries. The number of entries is given by the value of upsNumUPSs." ::= { upsInput 1 } upsInputEntry OBJECT-TYPE SYNTAX UpsInputEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing objects for a particular UPS." INDEX { upsIndex } ::= { upsInputTable 1 } UpsInputEntry ::= SEQUENCE { upsInputUtilityVoltage INTEGER, upsInputVoltage INTEGER, upsInputFailureSensitivity INTEGER, upsInputMaxVoltage INTEGER, upsInputMinVoltage INTEGER, upsInputFrequency INTEGER } upsInputUtilityVoltage OBJECT-TYPE SYNTAX INTEGER { vac100(1), vac120(2), vac208(3), vac220(4) -- 220/230/240 } ACCESS read-only STATUS mandatory DESCRIPTION "The UPS's utility voltage version." ::= { upsInputEntry 1 } upsInputVoltage OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The UPS's measured utility input voltage. The value of this object is the actual voltage * 10 (that is, to determine the actual voltage, divide the value of this object by 10)." ::= { upsInputEntry 2 } upsInputFailureSensitivity OBJECT-TYPE SYNTAX INTEGER { high(1), medium(2), low(3), auto(4) } ACCESS read-write STATUS mandatory DESCRIPTION "The sensitivity of the UPS to rapid changes in utility voltage (e.g., blackouts, spikes, or notches) or abnormal changes in utility frequency." DEFVAL { high } ::= { upsInputEntry 3 } upsInputMaxVoltage OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The UPS's maximum input voltage recorded since this object was last read. The value of this object is the actual voltage * 10 (that is, to determine the actual voltage, divide the value of this object by 10)." ::= { upsInputEntry 4 } upsInputMinVoltage OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The UPS's minimum input voltage recorded since this object was last read. The value of this object is the actual voltage * 10 (that is, to determine the actual voltage, divide the value of this object by 10)." ::= { upsInputEntry 5 } upsInputFrequency OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The UPS's present internal operating frequency in Hz. The value of this object is the actual frequency * 100 (that is, to determine the actual frequency, divide the value of this object by 100)." ::= { upsInputEntry 6 } --=============== upsOutput group =================== -- UPS Output Group -- Implementation of this group is mandatory if one or more UPSs -- are to be monitored -- This group covers information on the AC Outputs from each UPS upsOutputTable OBJECT-TYPE SYNTAX SEQUENCE OF UpsOutputEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of output table entries. The number of entries is given by the value of upsNumUPSs." ::= { upsOutput 1 } upsOutputEntry OBJECT-TYPE SYNTAX UpsOutputEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing objects for a particular UPS." INDEX { upsIndex } ::= { upsOutputTable 1 } UpsOutputEntry ::= SEQUENCE { upsOutputVoltage INTEGER, upsOutputUtilityVoltage INTEGER, upsOutputPower INTEGER } upsOutputVoltage OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The measured UPS output voltage. The value of this object is the actual voltage * 10 (that is, to determine the actual voltage, divide the value of this object by 10)." ::= { upsOutputEntry 1 } upsOutputUtilityVoltage OBJECT-TYPE SYNTAX INTEGER { vac225(1), vac230(2), vac240(3), vac220(4) } ACCESS read-write STATUS mandatory DESCRIPTION "The UPS's current on-battery output voltage setting (valid for 220/230/240 Vac version UPSs only). For other version UPSs, reading this object will always return a 0 and writing this object will have no effect." DEFVAL { vac225 } ::= { upsOutputEntry 2 } upsOutputPower OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The UPS's output load represented as a percentage of full rated load in Watts. The value of this object is the actual percentage * 10 (that is, to determine the actual percentage, divide the value of this object by 10)." ::= { upsOutputEntry 3 } --============== upsStatus group =================== -- UPS Status Group -- Implementation of this group is mandatory if one or more UPSs -- are to be monitored -- This group covers information on the Status of each UPS upsStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF UpsStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of status table entries. The number of entries is given by the value of upsNumUPSs." ::= { upsStatus 1 } upsStatusEntry OBJECT-TYPE SYNTAX UpsStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing objects for a particular UPS." INDEX { upsIndex } ::= { upsStatusTable 1 } UpsStatusEntry ::= SEQUENCE { upsStatusOperational INTEGER, upsStatusFault INTEGER, upsStatusTemp INTEGER } upsStatusOperational OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object contains 8 bits of information about the current operational status of the UPS. The bits are encoded as follows: BIT 7: 1=replace battery condition BIT 6: 1=low battery condition BIT 5: 1=overloaded output condition BIT 4: 1=on-battery mode of operation BIT 3: 1=on-line mode of operation BIT 2: 1=Smart Boost mode of operation (where applicable) BIT 1: 1=UPS shut down due to low battery, overload, or `sleep' mode BIT 0: 1=run time calibration running Note that bit 0 is the low-order bit." ::= { upsStatusEntry 1 } upsStatusFault OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object contains 8 bits of information about the current fault conditions of the UPS. The bits are encoded as follows: BIT 7: 1=UPS fault - internal temperature has exceeded nominal limits BIT 6: 1=UPS fault - bypass relay (where applicable) malfunction BIT 5: 1=UPS fault - battery charger failure BIT 4: 1=UPS in shut down mode via `S' command BIT 3: 1=UPS in `sleep' mode via `@ddd' command BIT 2: 1=UPS fault - main relay malfunction BIT 1: 1=UPS unable to transfer to on-battery operation due to overload BIT 0: 1=UPS's output unpowered due to low battery shut down Note that bit 0 is the low-order bit." ::= { upsStatusEntry 2 } upsStatusTemp OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The UPS's present internal operating temperature in degrees Fahrenheit. The value of this object is the actual temperature * 10 (that is, to determine the actual temperature, divide the value of this object by 10)." ::= { upsStatusEntry 3 } --=============== upsConfig group ==================== -- UPS Config Group -- Implementation of this group is mandatory if one or more UPSs -- are to be monitored -- This group covers information on the Configuration of each UPS upsConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF UpsConfigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of configuration table entries. The number of entries is given by the value of upsNumUPSs." ::= { upsConfig 1 } upsConfigEntry OBJECT-TYPE SYNTAX UpsConfigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing objects for a particular UPS." INDEX { upsIndex } ::= { upsConfigTable 1 } UpsConfigEntry ::= SEQUENCE { upsConfigAlarm INTEGER, upsConfigRestoreDefaults INTEGER } upsConfigAlarm OBJECT-TYPE SYNTAX INTEGER { uponUtilityFailure(1), thirtySecondsAfterUtilityFailure(2), lowBatteryOnly(3), noAudibleAlarm(4) } ACCESS read-write STATUS mandatory DESCRIPTION "The UPS's current audible alarm setting. The alarm may be set to activate immediately upon utility failure and for low battery condition, to activate 30 seconds after utility failure and immediately upon low battery condition, to activate upon low battery condition only, or to not activate under any conditions." DEFVAL { uponUtilityFailure } ::= { upsConfigEntry 1 } upsConfigRestoreDefaults OBJECT-TYPE SYNTAX INTEGER { restoreDefaults(1) } ACCESS read-write STATUS mandatory DESCRIPTION "This object may be written to force the UPS to restore the factory default settings for most of the UPS's customizable parameters. Reading this object will always return a 0." ::= { upsConfigEntry 2 } --=============== upsExtMeas group ==================== -- UPS ExtMeas Group -- Implementation of this group is mandatory if one or more UPSs -- are to be monitored AND an External Measurement Unit is attached -- to at least one UPS -- This group covers information on the External Measurement Unit of -- each UPS upsExtMeasTable OBJECT-TYPE SYNTAX SEQUENCE OF UpsExtMeasEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of external measurement table entries. The number of entries is the number of available UPSs to which External Measurement Units are attached." ::= { upsExtMeas 1 } upsExtMeasEntry OBJECT-TYPE SYNTAX UpsExtMeasEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing objects for a particular UPS." INDEX { upsIndex } ::= { upsExtMeasTable 1 } UpsExtMeasEntry ::= SEQUENCE { upsExtMeasFwVersion DisplayString, upsExtMeasTemp INTEGER, upsExtMeasHumidity INTEGER, upsExtMeasAlarmStatus INTEGER, upsExtMeasMaxTemp INTEGER, upsExtMeasMinTemp INTEGER, upsExtMeasMaxHumidity INTEGER, upsExtMeasMinHumidity INTEGER, upsExtMeasContact1AlarmControl INTEGER, upsExtMeasContact2AlarmControl INTEGER, upsExtMeasContact3AlarmControl INTEGER, upsExtMeasContact4AlarmControl INTEGER, upsExtMeasMaxTempAlarmControl INTEGER, upsExtMeasMinTempAlarmControl INTEGER, upsExtMeasMaxHumidityAlarmControl INTEGER, upsExtMeasMinHumidityAlarmControl INTEGER } upsExtMeasFwVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(0..1)) ACCESS read-only STATUS mandatory DESCRIPTION "The External Measurement Unit's firmware version letter." ::= { upsExtMeasEntry 1 } upsExtMeasTemp OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The local ambient temperature in degrees Fahrenheit as measured by the External Measurement Unit. The value of this object is the actual temperature * 100 (that is, to determine the actual temperature, divide the value of this object by 100)." ::= { upsExtMeasEntry 2 } upsExtMeasHumidity OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The local ambient relative humidity in percent as measured by the External Measurement Unit. The value of this object is the actual humidity * 10 (that is, to determine the actual humidity, divide the value of this object by 10)." ::= { upsExtMeasEntry 3 } upsExtMeasAlarmStatus OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object contains 8 bits of information about the current alarm status of the External Measurement Unit. The bits are encoded as follows: BIT 7: 1=Upper temperature limit exceeded BIT 6: 1=Lower temperature limit exceeded BIT 5: 1=Upper relative humidity limit exceeded BIT 4: 1=Lower relative humidity limit exceeded BIT 3: 1=Contact input channel #4 alarm state BIT 2: 1=Contact input channel #3 alarm state BIT 1: 1=Contact input channel #2 alarm state BIT 0: 1=Contact input channel #1 alarm state Note that bit 0 is the low-order bit." ::= { upsExtMeasEntry 4 } upsExtMeasMaxTemp OBJECT-TYPE SYNTAX INTEGER { ninetyDegreesF(1), oneHundredFifteenDegreesF(2), oneHundredThirtyDegreesF(3), oneHundredSeventyFiveDegreesF(4) } ACCESS read-write STATUS mandatory DESCRIPTION "The upper temperature limit at which an alarm will be sent." DEFVAL { ninetyDegreesF } ::= { upsExtMeasEntry 5 } upsExtMeasMinTemp OBJECT-TYPE SYNTAX INTEGER { fortyDegreesF(1), fiftyDegreesF(2), fiftyEightDegreesF(3), sixtyFiveDegreesF(4) } ACCESS read-write STATUS mandatory DESCRIPTION "The lower temperature limit at which an alarm will be sent." DEFVAL { fortyDegreesF } ::= { upsExtMeasEntry 6 } upsExtMeasMaxHumidity OBJECT-TYPE SYNTAX INTEGER { seventyPercent(1), eightyPercent(2), eightyFivePercent(3), ninetyPercent(4) } ACCESS read-write STATUS mandatory DESCRIPTION "The upper humidity limit at which an alarm will be sent." DEFVAL { seventyPercent } ::= { upsExtMeasEntry 7 } upsExtMeasMinHumidity OBJECT-TYPE SYNTAX INTEGER { tenPercent(1), twentyPercent(2), thirtyPercent(3), fortyPercent(4) } ACCESS read-write STATUS mandatory DESCRIPTION "The lower humidity limit at which an alarm will be sent." DEFVAL { tenPercent } ::= { upsExtMeasEntry 8 } upsExtMeasContact1AlarmControl OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The alarm enable state for the External Measurement Unit's contact input channel #1. If enabled, an alarm will be sent when contact input channel #1 has changed to abnormal state." ::= { upsExtMeasEntry 9 } upsExtMeasContact2AlarmControl OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The alarm enable state for the External Measurement Unit's contact input channel #2. If enabled, an alarm will be sent when contact input channel #2 has changed to abnormal state." ::= { upsExtMeasEntry 10 } upsExtMeasContact3AlarmControl OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The alarm enable state for the External Measurement Unit's contact input channel #3. If enabled, an alarm will be sent when contact input channel #3 has changed to abnormal state." ::= { upsExtMeasEntry 11 } upsExtMeasContact4AlarmControl OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The alarm enable state for the External Measurement Unit's contact input channel #4. If enabled, an alarm will be sent when contact input channel #4 has changed to abnormal state." ::= { upsExtMeasEntry 12 } upsExtMeasMaxTempAlarmControl OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The alarm enable state for the External Measurement Unit's upper temperature limit. If enabled, an alarm will be sent when the ambient temperature rises above the upper temperature limit." ::= { upsExtMeasEntry 13 } upsExtMeasMinTempAlarmControl OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The alarm enable state for the External Measurement Unit's lower temperature limit. If enabled, an alarm will be sent when the ambient temperature falls below the lower temperature limit." ::= { upsExtMeasEntry 14 } upsExtMeasMaxHumidityAlarmControl OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The alarm enable state for the External Measurement Unit's upper humidity limit. If enabled, an alarm will be sent when the ambient relative humidity rises above the upper humidity limit." ::= { upsExtMeasEntry 15 } upsExtMeasMinHumidityAlarmControl OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The alarm enable state for the External Measurement Unit's lower humidity limit. If enabled, an alarm will be sent when the ambient relative humidity falls below the lower humidity limit." ::= { upsExtMeasEntry 16 } --=============== upsAddlFuncs group ==================== -- UPS AddlFuncs Group -- Implementation of this group is mandatory if one or more UPSs -- are to be monitored AND at least one UPS is capable of supporting -- these additional functions -- This group covers information on the Additional Functions of each -- UPS upsAddlFuncsTable OBJECT-TYPE SYNTAX SEQUENCE OF UpsAddlFuncsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of additional functions table entries. The number of entries is the number of available UPSs which are capable of supporting these additional functions." ::= { upsAddlFuncs 1 } upsAddlFuncsEntry OBJECT-TYPE SYNTAX UpsAddlFuncsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing objects for a particular UPS." INDEX { upsIndex } ::= { upsAddlFuncsTable 1 } UpsAddlFuncsEntry ::= SEQUENCE { upsAddlFuncsNumBatteryPacks INTEGER, upsAddlFuncsNumBadBatteryPacks INTEGER, upsAddlFuncsOutputCurrent INTEGER, upsAddlFuncsOutputApparentPower INTEGER, upsAddlFuncsStatusOperational INTEGER, upsAddlFuncsStatusFault INTEGER, upsAddlFuncsConfigPassword OCTET STRING, upsAddlFuncsConfigDisable INTEGER, upsAddlFuncsConfigBypass INTEGER } upsAddlFuncsNumBatteryPacks OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of battery pack units connected to the UPS." ::= { upsAddlFuncsEntry 1 } upsAddlFuncsNumBadBatteryPacks OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of bad (faulty) battery pack units connected to the UPS." ::= { upsAddlFuncsEntry 2 } upsAddlFuncsOutputCurrent OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The true rms load current drawn from the UPS. The value of this object is the actual amperage * 100 (that is, to determine the actual amperage, divide the value of this object by 100)." ::= { upsAddlFuncsEntry 3 } upsAddlFuncsOutputApparentPower OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The UPS's output load represented as a percentage of full rated load in Volt-Amps. The value of this object is the actual percentage * 10 (that is, to determine the actual percentage, divide the value of this object by 10)." ::= { upsAddlFuncsEntry 4 } upsAddlFuncsStatusOperational OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object contains 8 bits of information about the current operational status of the UPS. The bits are encoded as follows: BIT 7: 1=UPS ready to power load upon return of normal line or upon user command BIT 6: 1=UPS ready to power load upon user command BIT 5: 1=UPS in bypass mode as a result of manual bypass control BIT 4: 1=UPS is returning from bypass mode BIT 3: 1=UPS in bypass mode as a result of UPS-Link or key command BIT 2: 1=UPS going to bypass mode as a result of UPS-Link or key command BIT 1: 1=not defined BIT 0: 1=wakeup mode - startup test lasting < 2 sec Note that bit 0 is the low-order bit." ::= { upsAddlFuncsEntry 5 } upsAddlFuncsStatusFault OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object contains 8 bits of information about the current fault conditions of the UPS. The bits are encoded as follows: BIT 7: reserved for future use BIT 6: reserved for future use BIT 5: reserved for future use BIT 4: 1=UPS fault - DC imbalance, UPS in bypass BIT 3: 1=UPS fault - output voltage select failure, UPS in bypass BIT 2: 1=UPS fault - bypass supply failure BIT 1: 1=UPS fault - Isolation Unit fan failure BIT 0: 1=UPS fault - Electronics Unit fan failure, UPS in bypass Note that bit 0 is the low-order bit." ::= { upsAddlFuncsEntry 6 } upsAddlFuncsConfigPassword OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION "The password that controls access to the UPS's LCD display. A maximum of 4 characters may be entered." ::= { upsAddlFuncsEntry 7 } upsAddlFuncsConfigDisable OBJECT-TYPE SYNTAX INTEGER { disableUps(1) } ACCESS read-write STATUS mandatory DESCRIPTION "This object may be written to immediately shut down the UPS, requiring a manual reset. Reading this object will always return a 0." ::= { upsAddlFuncsEntry 8 } upsAddlFuncsConfigBypass OBJECT-TYPE SYNTAX INTEGER { bypassMode(1), exitBypassMode(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This object may be written to cause the UPS to transfer to or from the bypass mode. Reading this object will always return a 0." ::= { upsAddlFuncsEntry 9 } END