REPEATER-REV4-MIB DEFINITIONS ::= BEGIN -- repeater-rev4-mib.txt -- Revision: 2.03.01 -- Part Number: 2170571-01 -- Date: April 17, 1996 -- Cabletron Systems, Inc. -- 35 Industrial Way, P.O. Box 5005 -- Rochester, NH 03867-0505 -- (603) 332-9400 -- support@ctron.com -- This module provides authoritative definitions for Cabletron's -- enterprise-specific repeater MIB. -- -- This module will be extended, as required. -- -- Cabletron Systems reserves the right to make changes in -- specification and other information contained in this document -- without prior notice. The reader should consult Cabletron Systems -- to determine whether any such changes have been made. -- -- In no event shall Cabletron Systems be liable for any incidental, -- indirect, special, or consequential damages whatsoever (including -- but not limited to lost profits) arising out of or related to this -- document or the information contained in it, even if Cabletron -- Systems has been advised of, known, or should have known, the -- possibility of such damages. -- -- Cabletron grants vendors, end-users, and other interested parties -- a non-exclusive license to use this Specification in connection -- with the management of Cabletron products. -- Copyright August 94 Cabletron Systems IMPORTS NetworkAddress, Counter FROM RFC1155-SMI DisplayString FROM RFC1213-MIB repeaterRev4 FROM CTRON-MIB-NAMES OBJECT-TYPE FROM RFC-1212; -- Textual Conventions -- DisplayString ::= OCTET STRING -- This data type is used to model textual information taken from -- the NVT ASCII character set. By convention, objects with this -- syntax, unless explicitly stated, are declared as having: -- -- SIZE (0..255) -- Repeater Node -- The following branch in the repeater MIB tree pertains to the repeater -- as a whole repeaterrev4 OBJECT IDENTIFIER ::= { repeaterRev4 4 } -- Repeater Management Object Definitions rptr OBJECT IDENTIFIER ::= { repeaterrev4 1 } rptrMgmt OBJECT IDENTIFIER ::= { rptr 1 } -- This section defines the management objects under the Repeater node. -- The implementation of this group of objects is mandatory. rptrMgmtName OBJECT-TYPE SYNTAX DisplayString (SIZE(20)) ACCESS read-write STATUS mandatory DESCRIPTION "The ASCII name assigned to this network." ::= { rptrMgmt 1} rptrMgmtPortCount OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Total number of ports residing on this lan segment." ::= { rptrMgmt 2} rptrMgmtPortsEnable OBJECT-TYPE SYNTAX INTEGER { noEnable(1), enable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Setting this object to Enable will cause all the ports residing in this network segment to be enabled. Setting this object to noEnable will have no effect. When read this object will always return noEnable." ::= { rptrMgmt 3 } rptrMgmtPortsOn OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Get the total number of ON ports in this network." ::= { rptrMgmt 4 } rptrMgmtPortsOper OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Get the number of operational ports in this network." ::= { rptrMgmt 5 } rptrMgmtBoardMap OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Get a map of the chassis slots occupied by the boards in this network." ::= { rptrMgmt 6 } rptrMgmtInterfaceNum OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Get the MIBII interface number of this network. A return of zero will mean this network is not associated with a MIBII interface." ::= { rptrMgmt 7 } rptrMgmtResetCounters OBJECT-TYPE SYNTAX INTEGER { normal(1), reseStaticCounters(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Setting this OID to 2 will reset the 'rptrPktStats', 'rptrProtocols' and 'rptrFrameSizes' RREV-4 branch static counters. Reading this OID will always return a 1." ::= { rptrMgmt 8 } -- Repeater Packet Statistical Object Definitions rptrStats OBJECT IDENTIFIER ::= { rptr 2 } -- This section defines the packet statistical objects under the -- Repeater node. -- The implementation of this group of objects is mandatory. rptrPktStats OBJECT IDENTIFIER ::= { rptrStats 1 } rptrPktStatsPackets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this repeater's total received packets." ::= { rptrPktStats 1 } rptrPktStatsBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this repeater's total received bytes." ::= { rptrPktStats 2 } rptrPktStatsColls OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this repeater's total collisions." ::= { rptrPktStats 3 } rptrPktStatsErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this repeater's total errors." ::= { rptrPktStats 4 } rptrPktStatsAlign OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this repeater's total frame alignment errors." ::= { rptrPktStats 5 } rptrPktStatsCRC OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this repeater's total CRC errors." ::= { rptrPktStats 6 } rptrPktStatsOOW OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this repeater's total out-of-window collisions." ::= { rptrPktStats 7 } rptrPktStatsNoRsc OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This counter is the number of packets on this network that the hardware has processed that the management has either not seen yet, in the case of an active network, or has missed missed all together, in the case of a once active network." ::= { rptrPktStats 8 } rptrPktStatsBroadcasts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This counter is the number of broadcast packets on this network that the hardware has processed." ::= { rptrPktStats 9 } rptrPktStatsMulticasts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This counter is the number of multicast packets on this network that the hardware has processed." ::= { rptrPktStats 10 } -- Repeater Protocol Statistical Object Definitions -- This section defines the protocol statistical objects under the -- Repeater node. The implementation of this group is optional, but -- within the group all of the elements are mandatory. rptrProtocols OBJECT IDENTIFIER ::= { rptrStats 2 } rptrProtocolsOSI OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this repeater's total received OSI packets." ::= { rptrProtocols 1 } rptrProtocolsNovell OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this repeater's total received Novell packets." ::= { rptrProtocols 2 } rptrProtocolsBanyan OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this repeater's total received Banyan packets." ::= { rptrProtocols 3 } rptrProtocolsDECNet OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this repeater's total received DECNet packets." ::= { rptrProtocols 4 } rptrProtocolsXNS OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this repeater's total received XNS packets." ::= { rptrProtocols 5 } rptrProtocolsIP OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this repeater's total received TCP/IP packets." ::= { rptrProtocols 6 } rptrProtocolsCtron OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this repeater's total received CTRON Management packets." ::= { rptrProtocols 7 } rptrProtocolsAppletalk OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this repeater's total received Appletalk packets." ::= { rptrProtocols 8 } rptrProtocolsOther OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this repeater's total received unknown protocol packets." ::= { rptrProtocols 9 } -- Repeater Frame Size Statistical Object Definitions rptrFrameSizes OBJECT IDENTIFIER ::= { rptrStats 3 } -- This section defines the frame size statistical objects under the -- Repeater node. The implementation of this group is optional, -- but within the group all of the elements are mandatory. rptrFrameSzRunt OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this repeater's total received packets of size less than 64 bytes." ::= { rptrFrameSizes 1 } rptrFrameSz64To127 OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this repeater's total received packets of size between 64 and 127 bytes." ::= { rptrFrameSizes 2 } rptrFrameSz128To255 OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this repeater's total received packets of size between 128 and 255 bytes." ::= { rptrFrameSizes 3 } rptrFrameSz256To511 OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this repeater's total received packets of size between 256 and 511 bytes." ::= { rptrFrameSizes 4 } rptrFrameSz512To1023 OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this repeater's total received packets of size between 512 and 1023 bytes." ::= { rptrFrameSizes 5 } rptrFrameSz1024To1518 OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this repeater's total received packets of size between 1024 and 1518 bytes." ::= { rptrFrameSizes 6 } rptrFrameSzGiant OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this repeater's total received packets of size greater than 1518 bytes." ::= { rptrFrameSizes 7 } -- Repeater Alarm Object Definitions rptrAlarms OBJECT IDENTIFIER ::= { rptr 3 } -- This section defines the alarm objects under the Repeater node. -- The implementation of this group is optional, but within the group all -- of the elements are mandatory. rptrAlarmsTrafEnable OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Get returns whether traffic alarms are enabled/disabled. Set allows for enabling/disabling of traffic alarms." ::= { rptrAlarms 1 } rptrAlarmsTrafThreshold OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The maximum number of packets that will be allowed before an alarm is generated." ::= { rptrAlarms 2 } rptrAlarmsCollEnable OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Get returns whether collision alarms are enabled/disabled. Set allows for enabling/disabling of collision alarms." ::= { rptrAlarms 3 } rptrAlarmsCollThreshold OBJECT-TYPE SYNTAX INTEGER (1..15) ACCESS read-write STATUS mandatory DESCRIPTION "The collision threshold is the maximum number of collisions within the time base that will be allowed before an alarm is generated." ::= { rptrAlarms 4 } rptrAlarmsErrEnable OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Get returns whether error alarms are enabled/disabled. Set allows for enabling/disabling of error alarms." ::= { rptrAlarms 5 } rptrAlarmsErrThreshold OBJECT-TYPE SYNTAX INTEGER (1..100) ACCESS read-write STATUS mandatory DESCRIPTION "The percentage of errors per good packet within the timebase that will cause an alarm. The units of this value is in seconds." ::= { rptrAlarms 6 } rptrAlarmsErrSource OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Get/Set a bit encoded map of which errors to include in the error sum, as follows: CRC_errors - Bit 0 - Least Significant Bit runts - Bit 1 OOW_colls - Bit 2 align_errs - Bit 3 undefined - Bit 4 Giants - Bit 5" ::= { rptrAlarms 7 } rptrAlarmsAlarmTimebase OBJECT-TYPE SYNTAX INTEGER (10..999999) ACCESS read-write STATUS mandatory DESCRIPTION "The alarm timebase, in seconds." ::= { rptrAlarms 8 } rptrAlarmsBroadEnable OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Get returns whether broadcast alarms are enabled/disabled. Set allows for enabling/disabling of broadcast alarms." ::= { rptrAlarms 9 } rptrAlarmsBroadThreshold OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The broadcase threshold represents the maximum number of broadcasts that are allowed during the time base before an alarm is generated." ::= { rptrAlarms 10 } -- Repeater Redundancy Object Definitions -- Repeater redundancy as a whole is an optional implementation. -- However, if any group concerning redundancy is implemented, all -- of the groups involved in the redundancy implementation must be -- provided. rptrRedundancy OBJECT IDENTIFIER ::= { rptr 4 } -- This section defines the redundancy objects under the Repeater node. rptrRedund OBJECT IDENTIFIER ::= { rptrRedundancy 1 } rptrRedundReset OBJECT-TYPE SYNTAX INTEGER { noReset(1), reset(2) } ACCESS read-write STATUS mandatory DESCRIPTION "If this object is set to Reset it will cause a reset of the redundancy object to occur. Setting this object to NoReset will do nothing. This object will always be read as NoReset." ::= { rptrRedund 1 } rptrRedundPollInterval OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Get/Set the number of seconds between polls for redundancy." ::= { rptrRedund 2 } rptrRedundTestTOD OBJECT-TYPE SYNTAX DisplayString (SIZE(8)) ACCESS read-write STATUS mandatory DESCRIPTION "Get/Set the time of day at which the redundant circuits will be tested. The format of the time string is hh:mm:ss." ::= { rptrRedund 3 } rptrRedundPerformTest OBJECT-TYPE SYNTAX INTEGER { noTest(1), test(2) } ACCESS read-write STATUS mandatory DESCRIPTION "If this object is set to Test it will cause a test of the redundant circuits to be performed. Setting this object to NoTest will have no effect. When read this object will always return NoTest." ::= { rptrRedund 4 } rptrRedundMaxCrcts OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns the maximum number of circuits which may exist on this network." ::= { rptrRedund 5 } -- Repeater Redundant Circuit Object Definitions -- This section defines a table of redundant circuit objects under -- the Repeater node. rptrRedundCrctTable OBJECT-TYPE SYNTAX SEQUENCE OF RptrRedundCrctEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of redundant circuit objects for this repeater." ::= { rptrRedundancy 2 } rptrRedundCrctEntry OBJECT-TYPE SYNTAX RptrRedundCrctEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of objects for a particular redundant circuit." INDEX { rptrRedundCrctId } ::= { rptrRedundCrctTable 1 } RptrRedundCrctEntry ::= SEQUENCE { rptrRedundCrctId INTEGER, rptrRedundCrctName OCTET STRING, rptrRedundCrctRetrys INTEGER, rptrRedundCrctNumBPs INTEGER, rptrRedundCrctNumAddr INTEGER, rptrRedundCrctAddAddr NetworkAddress, rptrRedundCrctDelAddr NetworkAddress, rptrRedundCrctEnable INTEGER, rptrRedundCrctReset INTEGER } rptrRedundCrctId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns the index for a member circuit in the table of redundant circuits." ::= { rptrRedundCrctEntry 1 } rptrRedundCrctName OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION "Get/Set the name of the indicated circuit." ::= { rptrRedundCrctEntry 2 } rptrRedundCrctRetrys OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Get/Set the the number of unanswered polls allowed for the circuit." ::= { rptrRedundCrctEntry 3 } rptrRedundCrctNumBPs OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Get the number of board/port combinations associated with the circuit." ::= { rptrRedundCrctEntry 4 } rptrRedundCrctNumAddr OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Get the number of IP Addresses associated with the circuit." ::= { rptrRedundCrctEntry 5 } rptrRedundCrctAddAddr OBJECT-TYPE SYNTAX NetworkAddress ACCESS read-write STATUS mandatory DESCRIPTION "Add an IP Address to the polling list for the indicated circuit." ::= { rptrRedundCrctEntry 6 } rptrRedundCrctDelAddr OBJECT-TYPE SYNTAX NetworkAddress ACCESS read-write STATUS mandatory DESCRIPTION "Delete an IP Address from the polling list of the indicated circuit." ::= { rptrRedundCrctEntry 7 } rptrRedundCrctEnable OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "If this object is set to Enable, the circuit is enabled. If this object is set to Disable, the circuit is disbabled. When read, this object returns the state of the object based on the last request made." ::= { rptrRedundCrctEntry 8 } rptrRedundCrctReset OBJECT-TYPE SYNTAX INTEGER { noReset(1), reset(2) } ACCESS read-write STATUS mandatory DESCRIPTION "If this object is set to Reset, the circuit is reset. All of the circuit's associated boards and ports are returned to NOT_USED, any associated IP Addresses are purged from the circuit's address list, the name is cleared, and the retry count is reset to a default value. Setting this object to NoReset has no effect. When read, NoReset is always returned." ::= { rptrRedundCrctEntry 9 } -- Repeater Redundant Port Object Definitions -- This section defines a table of redundant port objects under -- the Repeater node. rptrRedundPortTable OBJECT-TYPE SYNTAX SEQUENCE OF RptrRedundPortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of redundant port objects for this repeater." ::= { rptrRedundancy 3 } rptrRedundPortEntry OBJECT-TYPE SYNTAX RptrRedundPortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A redundant port entry containing objects pertaining to a particular redundant port." INDEX { rptrRedundPortCrctId, rptrRedundPortId } ::= { rptrRedundPortTable 1 } RptrRedundPortEntry ::= SEQUENCE { rptrRedundPortId INTEGER, rptrRedundPortCrctId INTEGER, rptrRedundPortNum INTEGER, rptrRedundPortBoardNum INTEGER, rptrRedundPortType INTEGER } rptrRedundPortId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A unique value identifying an element in a sequence of member ports which belong to a circuit in the table of redundant circuits. This value is not a port number; rather it is a value which goes from 1 to the maximum number of ports which may be included in a redundant circuit." ::= { rptrRedundPortEntry 1 } rptrRedundPortCrctId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A unique value identifying a member circuit in the table of redundant circuits. This value is similar to rptrRedundCrctId." ::= { rptrRedundPortEntry 2 } rptrRedundPortNum OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns the port number of a member port belonging to a redundant circuit." ::= { rptrRedundPortEntry 3 } rptrRedundPortBoardNum OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns the board number of a member port belonging to a redundant circuit." ::= { rptrRedundPortEntry 4 } rptrRedundPortType OBJECT-TYPE SYNTAX INTEGER { notUsed(1), primary(2), backup(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Return the state of a port associated with the indicated circuit." ::= { rptrRedundPortEntry 5 } -- Repeater Redundant IP Address Object Definitions -- This section defines a table of redundant IP Address objects under -- the Repeater node. The implementation of this group is optional, -- but within the group all of the elements are mandatory. rptrRedundAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF RptrRedundAddrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of redundant IP Address objects which belong to a circuit for this repeater." ::= { rptrRedundancy 4 } rptrRedundAddrEntry OBJECT-TYPE SYNTAX RptrRedundAddrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A entry containing objects pertaining to a particular redundant IP Address which belongs to a circuit." INDEX { rptrRedundAddrCrctId, rptrRedundAddrId } ::= { rptrRedundAddrTable 1 } RptrRedundAddrEntry ::= SEQUENCE { rptrRedundAddrId INTEGER, rptrRedundAddrCrctId INTEGER, rptrRedundAddrIPAddr NetworkAddress } rptrRedundAddrId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A unique value identifying an element in a sequence of member IP Addresses which belong to a circuit in the table of redundant circuits. This value goes from 1 to the maximum number of IP Addresses which may be included in a redundant circuit." ::= { rptrRedundAddrEntry 1 } rptrRedundAddrCrctId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A unique value identifying a member circuit in the table of redundant circuits. This value is similar to rptrRedundCrctId." ::= { rptrRedundAddrEntry 2 } rptrRedundAddrIPAddr OBJECT-TYPE SYNTAX NetworkAddress ACCESS read-only STATUS mandatory DESCRIPTION "Returns an IP Address associated with the indicated circuit." ::= { rptrRedundAddrEntry 3 } -- Repeater Source Address List Object Definitions -- Repeater Source Addressing List as a whole is an optional implementation. -- However, if any group of source addressing objects is implemented, the -- entire set of source addressing object groups must be implemented. rptrSourceAddress OBJECT IDENTIFIER ::= { rptr 5 } -- This section defines a table of Source Address List objects under the -- Repeater node. rptrSrcAddrListTable OBJECT-TYPE SYNTAX SEQUENCE OF RptrSrcAddrListEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table defines the source address list that is defined at the repeater level." ::= { rptrSourceAddress 1 } rptrSrcAddrListEntry OBJECT-TYPE SYNTAX RptrSrcAddrListEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Defines a specific source address object." INDEX { rptrSrcAddrListId } ::= { rptrSrcAddrListTable 1 } RptrSrcAddrListEntry ::= SEQUENCE { rptrSrcAddrListId INTEGER, rptrSrcAddrAddressList OCTET STRING } rptrSrcAddrListId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index into a table of source address seen by this repeater." ::= { rptrSrcAddrListEntry 1 } rptrSrcAddrAddressList OBJECT-TYPE SYNTAX OCTET STRING (SIZE(6)) ACCESS read-only STATUS mandatory DESCRIPTION "Returns a source address seen by this repeater." ::= { rptrSrcAddrListEntry 2 } -- Repeater Source Address Source Object Definitions -- This section defines a table of Source Address Source objects under -- the Repeater node. rptrSrcAddrSrcTable OBJECT-TYPE SYNTAX SEQUENCE OF RptrSrcAddrSrcTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table defines the list of all source addresses that have been seen." ::= { rptrSourceAddress 2 } rptrSrcAddrSrcTableEntry OBJECT-TYPE SYNTAX RptrSrcAddrSrcTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Describes a particular source address source entry." INDEX { rptrSrcAddrSrcTableEntryId } ::= { rptrSrcAddrSrcTable 1 } RptrSrcAddrSrcTableEntry ::= SEQUENCE { rptrSrcAddrSrcTableEntryId OCTET STRING, rptrSrcAddrSrcTableEntryPort INTEGER, rptrSrcAddrSrcTableEntryPortGroup INTEGER } rptrSrcAddrSrcTableEntryId OBJECT-TYPE SYNTAX OCTET STRING (SIZE(6)) ACCESS read-only STATUS mandatory DESCRIPTION "Returns the source address to which this table's information pertains." ::= { rptrSrcAddrSrcTableEntry 1 } rptrSrcAddrSrcTableEntryPort OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns the port# of the port that sourced the source address." ::= { rptrSrcAddrSrcTableEntry 2 } rptrSrcAddrSrcTableEntryPortGroup OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns the port group# of the port that sourced the source address." ::= { rptrSrcAddrSrcTableEntry 3 } -- Repeater Source Address Source Object Definitions -- This section defines a table of Source Address Source objects under -- the Repeater node. rptrSrcAddrMgmt OBJECT IDENTIFIER ::= { rptrSourceAddress 3 } rptrSrcAddrMgmtSrcAgeInterval OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Get/Set source addressing ageing interval." ::= { rptrSrcAddrMgmt 1 } rptrSrcAddrMgmtPortLock OBJECT-TYPE SYNTAX INTEGER { unlock(1), lock(2), portMisMatch(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Setting this object to Lock will activate the network port security lock. Setting a value of portMisMatch(3) is invalid. A value of portMisMatch(3) reflects that not all ports are at the same value." ::= { rptrSrcAddrMgmt 2 } rptrSrcAddrMgmtActiveUsers OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Get the number of active users on this network." ::= { rptrSrcAddrMgmt 3 } rptrSrcAddrMgmtHashType OBJECT-TYPE SYNTAX INTEGER { noDecHash(1), decHash(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Defines the type of hashing that will be used for source address management. In a DEC-NET environment or a combination fo DEC-NET and non DEC-NET users where source address hash access is a concern a value of decHash(2) may yield better results. For non DEC-NET users a value of noDecHash(1) is preferred." DEFVAL { noDecHash } ::= { rptrSrcAddrMgmt 4 } -- This section control trap enables and disables at the network level. -- Setting these objects is equivalent to setting the same value for -- each port on this network. rptrTrap OBJECT IDENTIFIER ::= { rptr 6 } rptrHwTrapSet OBJECT IDENTIFIER ::= { rptrTrap 1 } rptrSaTrapSet OBJECT IDENTIFIER ::= { rptrTrap 2 } rptrHwTrapSetLink OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2), other(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Enables and disables link traps for this network. Setting a value of disable(1) is equivalent to setting all instances of rptrPortHwTrapSetLink to a value of disable(1). Setting a value of enable(2) is equivalent to setting all instances of rptrPortHwTrapSetLink to a value of disable(2). Setting a value of other(3) is not allowed. This object will read with the value of disable(1) if all instances of rptrPortHwTrapSetLink for this network are currently set to a value of disable(1). This object will read with the value of enable(2) if all instances of rptrPortHwTrapSetLink for this network are currently set to a value of enable(2). This object will read with the value of other(3) if all instances of rptrPortHwTrapSetLink for this network are not currently set to a value the same value." ::= { rptrHwTrapSet 1 } rptrHwTrapSetSeg OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2), other(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Enables and disables segmentation traps for this network. Setting a value of disable(1) is equivalent to setting all instances of rptrPortHwTrapSetSeg to a value of disable(1). Setting a value of enable(2) is equivalent to setting all instances of rptrPortHwTrapSetSeg to a value of disable(2). Setting a value of other(3) is not allowed. This object will read with the value of disable(1) if all instances of rptrPortHwTrapSetSeg for this network are currently set to a value of disable(1). This object will read with the value of enable(2) if all instances of rptrPortHwTrapSetSeg for this network are currently set to a value of enable(2). This object will read with the value of other(3) if all instances of rptrPortHwTrapSetSeg for this network are not currently set to a value the same value." ::= { rptrHwTrapSet 2 } rptrSaTrapSetSrcaddr OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2), other(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Enables and disables source address traps for this network. Setting a value of disable(1) is equivalent to setting all instances of rptrPortSaTrapSetSrcaddr to a value of disable(1). Setting a value of enable(2) is equivalent to setting all instances of rptrPortSaTrapSetSrcaddr to a value of disable(2). Setting a value of other(3) is not allowed. This object will read with the value of disable(1) if all instances of rptrPortSaTrapSetSrcaddr for this network are currently set to a value of disable(1). This object will read with the value of enable(2) if all instances of rptrPortSaTrapSetSrcaddr for this network are currently set to a value of enable(2). This object will read with the value of other(3) if all instances of rptrPortSaTrapSetSrcaddr for this network are not currently set to a value the same value." ::= { rptrSaTrapSet 1 } rptrSaSecurity OBJECT IDENTIFIER ::= { rptr 7 } rptrSecurityLockState OBJECT-TYPE SYNTAX INTEGER { unlock(1), lock(2), portMisMatch(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Setting this object to Lock will activate the network port security lock. Setting a value of portMisMatch(3) is invalid. A value of portMisMatch(3) reflects that not all ports are at the same value." ::= { rptrSaSecurity 1 } rptrSecuritySecureState OBJECT-TYPE SYNTAX INTEGER { secure(1), nonSecure(2), portMisMatch(3) } ACCESS read-only STATUS mandatory DESCRIPTION "The status of source address security of the network. Ports on the network that are secure(1), can be locked in order to enable security. nonSecure(2) ports cannot be locked. Setting a value of portMisMatch(3) is invalid. A value of portMisMatch(3) reflects that not all ports are at the same value." ::= { rptrSaSecurity 2 } rptrSecurityLearnState OBJECT-TYPE SYNTAX INTEGER { learn(1), noLearn(2), portMisMatch(3) } ACCESS read-write STATUS mandatory DESCRIPTION "The learn state of the network. This object will only be applied to ports that are unlocked. If set to learn(1), all addresses are deleted on the ports and learning begins once again. If it is set to noLearn(2), learning stops on the port. Setting a value of portMisMatch(3) is invalid. A value of portMisMatch(3) reflects that not all ports are at the same value." ::= { rptrSaSecurity 3 } rptrSecurityLearnMode OBJECT-TYPE SYNTAX INTEGER { oneTime(1), continuous(2), portMisMatch(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Get/Set the learn mode of the network. If set to onetime learn mode oneTime(1), each port is capable of learning two addresses and securing on both destination and source addresses once they are locked. If set to continuous learn continuous(2), all addresses are initially deleted and each port continuously replaces the existing secure source address with the latest source address it sees. Setting a value of portMisMatch(3) is invalid. A value of portMisMatch(3) reflects that not all ports are at the same value." ::= { rptrSaSecurity 4 } -- Repeater Port Group Node -- The following branch in the repeater MIB tree pertains to individual -- Repeater Port Group Node -- The following branch in the repeater MIB tree pertains to individual -- groups of repeater ports rptrPortGroup OBJECT IDENTIFIER ::= { repeaterrev4 2 } -- Repeater Port Group Management Object Definitions -- This section defines a table of Port Group Management objects under -- the Repeater node. The implementation of this group is optional, -- but within the group all of the elements are mandatory. rptrPortGrpMgmtTable OBJECT-TYPE SYNTAX SEQUENCE OF RptrPortGrpMgmtEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of port management objects for this repeater node." ::= { rptrPortGroup 1 } rptrPortGrpMgmtEntry OBJECT-TYPE SYNTAX RptrPortGrpMgmtEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing objects pertaining to port management for a port group." INDEX { rptrPortGrpMgmtGrpId } ::= { rptrPortGrpMgmtTable 1 } RptrPortGrpMgmtEntry ::= SEQUENCE { rptrPortGrpMgmtGrpId INTEGER, rptrPortGrpMgmtName DisplayString, rptrPortGrpMgmtPortCount INTEGER, rptrPortGrpMgmtPortsEnable INTEGER, rptrPortGrpMgmtPortsOn INTEGER, rptrPortGrpMgmtPortsOper INTEGER, rptrPortGrpMgmtLogPortCount INTEGER } rptrPortGrpMgmtGrpId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port group for which the information in this table pertains." ::= { rptrPortGrpMgmtEntry 1 } rptrPortGrpMgmtName OBJECT-TYPE SYNTAX DisplayString (SIZE(20)) ACCESS read-write STATUS mandatory DESCRIPTION "Gets/Sets a name for the specified port group." ::= { rptrPortGrpMgmtEntry 2 } rptrPortGrpMgmtPortCount OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Get total number of ports contained on the board. Notice that this is the physical port count." ::= { rptrPortGrpMgmtEntry 3 } rptrPortGrpMgmtPortsEnable OBJECT-TYPE SYNTAX INTEGER { noEnable(1), enable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Setting this object to Enable will cause all the ports residing in this network segment to be enabled. Setting this object to noEnable will have no effect. When read this object will always return noEnable." ::= { rptrPortGrpMgmtEntry 4 } rptrPortGrpMgmtPortsOn OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Get total number of ON ports in this port group." ::= { rptrPortGrpMgmtEntry 5 } rptrPortGrpMgmtPortsOper OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Get total number of operational ports in the port group." ::= { rptrPortGrpMgmtEntry 6 } rptrPortGrpMgmtLogPortCount OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Get total number of ports contained in this port group." ::= { rptrPortGrpMgmtEntry 7 } -- Repeater Port Group Statistical Object Definitions rptrPortGrpStats OBJECT IDENTIFIER ::= { rptrPortGroup 2 } -- Repeater Port Group Packet Statistical Object Definitions -- This section defines a table of Port Group Packet Statistical objects -- under the Repeater node. The implementation of this group is optional, -- but within the group all of the elements are mandatory. rptrPortGrpPktStatsTbl OBJECT-TYPE SYNTAX SEQUENCE OF RptrPortGrpPktStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table provides packet statistics for port group." ::= { rptrPortGrpStats 1 } rptrPortGrpPktStatsEntry OBJECT-TYPE SYNTAX RptrPortGrpPktStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Defines a specific packet statistics entry." INDEX { rptrPortGrpPktStatsId } ::= { rptrPortGrpPktStatsTbl 1 } RptrPortGrpPktStatsEntry ::= SEQUENCE { rptrPortGrpPktStatsId INTEGER, rptrPortGrpPktStatsPkts Counter, rptrPortGrpPktStatsBytes Counter, rptrPortGrpPktStatsColls Counter, rptrPortGrpPktStatsErrors Counter, rptrPortGrpPktStatsAlign Counter, rptrPortGrpPktStatsCRC Counter, rptrPortGrpPktStatsOOW Counter, rptrPortGrpPktStatsBroadcasts Counter, rptrPortGrpPktStatsMulticasts Counter } rptrPortGrpPktStatsId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port group for which the information in this table pertains." ::= { rptrPortGrpPktStatsEntry 1 } rptrPortGrpPktStatsPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Return this port group's total received packets." ::= { rptrPortGrpPktStatsEntry 2 } rptrPortGrpPktStatsBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Return this port group's total received bytes." ::= { rptrPortGrpPktStatsEntry 3 } rptrPortGrpPktStatsColls OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Return this port group's total collisions." ::= { rptrPortGrpPktStatsEntry 4 } rptrPortGrpPktStatsErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Return this port group's total errors." ::= { rptrPortGrpPktStatsEntry 5 } rptrPortGrpPktStatsAlign OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Return this port group's total frame alignment errors." ::= { rptrPortGrpPktStatsEntry 6 } rptrPortGrpPktStatsCRC OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Return this port group's total CRC errors." ::= { rptrPortGrpPktStatsEntry 7 } rptrPortGrpPktStatsOOW OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Return this port group's total out-of-window collisions." ::= { rptrPortGrpPktStatsEntry 8 } rptrPortGrpPktStatsBroadcasts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Return this port group's total received broadcast packets." ::= { rptrPortGrpPktStatsEntry 9 } rptrPortGrpPktStatsMulticasts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Return this port group's total received multicast packets." ::= { rptrPortGrpPktStatsEntry 10 } -- Repeater Port Group Protocol Statistical Object Definitions -- This section defines a table of Port Group Protocol Statistical objects -- under the Repeater node. The implementation of this group is optional, -- but within the group all of the elements are mandatory. rptrPortGrpProtocolTbl OBJECT-TYPE SYNTAX SEQUENCE OF RptrPortGrpProtocolEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Provides port group protocol statistics." ::= { rptrPortGrpStats 2 } rptrPortGrpProtocolEntry OBJECT-TYPE SYNTAX RptrPortGrpProtocolEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Defines a specific port group protocol statistics entry." INDEX { rptrPortGrpProtocolId } ::= { rptrPortGrpProtocolTbl 1 } RptrPortGrpProtocolEntry ::= SEQUENCE { rptrPortGrpProtocolId INTEGER, rptrPortGrpProtocolOSI Counter, rptrPortGrpProtocolNovell Counter, rptrPortGrpProtocolBanyan Counter, rptrPortGrpProtocolDECNet Counter, rptrPortGrpProtocolXNS Counter, rptrPortGrpProtocolIP Counter, rptrPortGrpProtocolCtron Counter, rptrPortGrpProtocolAppletalk Counter, rptrPortGrpProtocolOther Counter } rptrPortGrpProtocolId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port group for which the information in this table pertains." ::= { rptrPortGrpProtocolEntry 1 } rptrPortGrpProtocolOSI OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Return this port group's total received OSI packets." ::= { rptrPortGrpProtocolEntry 2 } rptrPortGrpProtocolNovell OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Return this port group's total received Novell packets." ::= { rptrPortGrpProtocolEntry 3 } rptrPortGrpProtocolBanyan OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Return this port group's total received Banyan packets." ::= { rptrPortGrpProtocolEntry 4 } rptrPortGrpProtocolDECNet OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Return this port group's total received DECNet packets." ::= { rptrPortGrpProtocolEntry 5 } rptrPortGrpProtocolXNS OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Return this port group's total received XNS packets." ::= { rptrPortGrpProtocolEntry 6 } rptrPortGrpProtocolIP OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Return this port group's total received TCP/IP packets." ::= { rptrPortGrpProtocolEntry 7 } rptrPortGrpProtocolCtron OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Return this port group's total received CTRON Management packets." ::= { rptrPortGrpProtocolEntry 8 } rptrPortGrpProtocolAppletalk OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Return this port group's total received Appletalk packets." ::= { rptrPortGrpProtocolEntry 9 } rptrPortGrpProtocolOther OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Return this port group's total received unknown protocol packets." ::= { rptrPortGrpProtocolEntry 10 } -- Repeater Port Group Frame Size Statistical Object Definitions -- This section defines a table of Port Group Frame Size Statistical -- objects under the Repeater node. The implementation of this group -- is optional, but within the group all of the elements are mandatory. rptrPortGrpFrameSzTbl OBJECT-TYPE SYNTAX SEQUENCE OF RptrPortGrpFrameSzEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Defines frame sizes as seen by this port group." ::= { rptrPortGrpStats 3 } rptrPortGrpFrameSzEntry OBJECT-TYPE SYNTAX RptrPortGrpFrameSzEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Defines a particular frame size entry." INDEX { rptrPortGrpFrameSzId } ::= { rptrPortGrpFrameSzTbl 1 } RptrPortGrpFrameSzEntry ::= SEQUENCE { rptrPortGrpFrameSzId INTEGER, rptrPortGrpFrameSzRunt Counter, rptrPortGrpFrameSz64To127 Counter, rptrPortGrpFrameSz128To255 Counter, rptrPortGrpFrameSz256To511 Counter, rptrPortGrpFrameSz512To1023 Counter, rptrPortGrpFrameSz1024To1518 Counter, rptrPortGrpFrameSzGiant Counter } rptrPortGrpFrameSzId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port group for which the information in this table pertains." ::= { rptrPortGrpFrameSzEntry 1 } rptrPortGrpFrameSzRunt OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Return this port group's total received packets of size less than 64 bytes." ::= { rptrPortGrpFrameSzEntry 2 } rptrPortGrpFrameSz64To127 OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Return this port group's total received packets of size between 64 and 127 bytes." ::= { rptrPortGrpFrameSzEntry 3 } rptrPortGrpFrameSz128To255 OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Return this port group's total received packets of size between 128 and 255 bytes." ::= { rptrPortGrpFrameSzEntry 4 } rptrPortGrpFrameSz256To511 OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Return this port group's total received packets of size between 256 and 511 bytes." ::= { rptrPortGrpFrameSzEntry 5 } rptrPortGrpFrameSz512To1023 OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Return this port group's total received packets of size between 512 and 1023 bytes." ::= { rptrPortGrpFrameSzEntry 6 } rptrPortGrpFrameSz1024To1518 OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Return this port group's total received packets of size between 1024 and 1518 bytes." ::= { rptrPortGrpFrameSzEntry 7 } rptrPortGrpFrameSzGiant OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Return this port group's total received packets of size greater than 1518 bytes." ::= { rptrPortGrpFrameSzEntry 8 } -- Repeater Port Group Alarm Object Definitions -- This section defines a table of Port Group Alarm objects under -- the Repeater node. The implementation of this group is optional, -- but within the group all of the elements are mandatory. rptrPortGrpAlarmTable OBJECT-TYPE SYNTAX SEQUENCE OF RptrPortGrpAlarmEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of port group alarm objects for this repeater node." ::= { rptrPortGroup 3 } rptrPortGrpAlarmEntry OBJECT-TYPE SYNTAX RptrPortGrpAlarmEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing objects pertaining to port group alarms for a port group." INDEX { rptrPortGrpAlarmId } ::= { rptrPortGrpAlarmTable 1 } RptrPortGrpAlarmEntry ::= SEQUENCE { rptrPortGrpAlarmId INTEGER, rptrPortGrpAlarmTrafEnable INTEGER, rptrPortGrpAlarmTrafThreshold INTEGER, rptrPortGrpAlarmTrafGrpDisable INTEGER, rptrPortGrpAlarmCollEnable INTEGER, rptrPortGrpAlarmCollThreshold INTEGER, rptrPortGrpAlarmCollBdDisable INTEGER, rptrPortGrpAlarmErrEnable INTEGER, rptrPortGrpAlarmErrThreshold INTEGER, rptrPortGrpAlarmErrSource INTEGER, rptrPortGrpAlarmErrGrpDisable INTEGER, rptrPortGrpAlarmBroadEnable INTEGER, rptrPortGrpAlarmBroadThreshold INTEGER, rptrPortGrpAlarmBroadGrpDisable INTEGER } rptrPortGrpAlarmId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port group for which the information in this table pertains." ::= { rptrPortGrpAlarmEntry 1 } rptrPortGrpAlarmTrafEnable OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Get returns whether traffic alarms are enabled/disabled. Set allows for enabling/disabling of traffic alarms." ::= { rptrPortGrpAlarmEntry 2 } rptrPortGrpAlarmTrafThreshold OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The maximum number of packets that will be allowed before an alarm is generated." ::= { rptrPortGrpAlarmEntry 3 } rptrPortGrpAlarmTrafGrpDisable OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Set will permit a port group to be disabled on a traffic alarm condition. Get will show whether the port group disabling is allowed or not." ::= { rptrPortGrpAlarmEntry 4 } rptrPortGrpAlarmCollEnable OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Get returns whether collision alarms are enabled/disabled. Set allows for enabling/disabling of collision alarms." ::= { rptrPortGrpAlarmEntry 5 } rptrPortGrpAlarmCollThreshold OBJECT-TYPE SYNTAX INTEGER (1..999999) ACCESS read-write STATUS mandatory DESCRIPTION "The collision threshold is the maximum number of collisions within the time base that will be allowed before an alaram is generated." ::= { rptrPortGrpAlarmEntry 6 } rptrPortGrpAlarmCollBdDisable OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Set will permit a port group to be disabled on a collision alarm condition. Get will show whether the port group disabling is allowed or not." ::= { rptrPortGrpAlarmEntry 7 } rptrPortGrpAlarmErrEnable OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Get returns whether error alarms are enabled/disabled. Set allows for enabling/disabling of error alarms." ::= { rptrPortGrpAlarmEntry 8 } rptrPortGrpAlarmErrThreshold OBJECT-TYPE SYNTAX INTEGER (1..100) ACCESS read-write STATUS mandatory DESCRIPTION "Get/Set the percentage of errors per good packet within the timebase that will cause an alarm." ::= { rptrPortGrpAlarmEntry 9 } rptrPortGrpAlarmErrSource OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Get/Set a bit encoded map of which errors to include in the error sum, as follows: CRC_errors - Bit 0 - Least Significant Bit runts - Bit 1 OOW_colls - Bit 2 align_errs - Bit 3 undefined - Bit 4 Giants - Bit 5" ::= { rptrPortGrpAlarmEntry 10 } rptrPortGrpAlarmErrGrpDisable OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Set will permit a port group to be disabled on an error alarm condition. Get will show whether the port group disabling is allowed or not." ::= { rptrPortGrpAlarmEntry 11 } rptrPortGrpAlarmBroadEnable OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Get returns whether broadcast alarms are enabled/disabled. Set allows for enabling/disabling of broadcast alarms." ::= { rptrPortGrpAlarmEntry 12 } rptrPortGrpAlarmBroadThreshold OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The broadcase threshold represents the maximum number of broadcasts that are allowed during the time base before an alarm is generated." ::= { rptrPortGrpAlarmEntry 13 } rptrPortGrpAlarmBroadGrpDisable OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Set will permit a port group to be disabled on a broadcast alarm condition. Get will show whether the port group disabling is allowed or not." ::= { rptrPortGrpAlarmEntry 14 } -- Repeater Port Group Source Address Object Definitions -- This section defines a table of Port Group Source Address objects -- under the Repeater node. The implementation of this group is optional, -- but within the group all of the elements are mandatory. rptrPortGrpSrcAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF RptrPortGrpSrcAddrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table provides a list of the number of active users that have been seen by port group." ::= { rptrPortGroup 4 } rptrPortGrpSrcAddrEntry OBJECT-TYPE SYNTAX RptrPortGrpSrcAddrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Defines a specific active user entry." INDEX { rptrPortGrpSrcAddrId } ::= { rptrPortGrpSrcAddrTable 1 } RptrPortGrpSrcAddrEntry ::= SEQUENCE { rptrPortGrpSrcAddrId INTEGER, rptrPortGrpSrcAddrActiveUsers INTEGER } rptrPortGrpSrcAddrId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port group for which the information in this table pertains." ::= { rptrPortGrpSrcAddrEntry 1 } rptrPortGrpSrcAddrActiveUsers OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns the total number of active users seen by this port group." ::= { rptrPortGrpSrcAddrEntry 2 } -- port group level trap enable and disables rptrPortGrpTrap OBJECT IDENTIFIER ::= { rptrPortGroup 5 } rptrPortGrpHwTrapSet OBJECT IDENTIFIER ::= { rptrPortGrpTrap 1 } rptrPortGrpSaTrapSet OBJECT IDENTIFIER ::= { rptrPortGrpTrap 2 } rptrPortGrpHwTrapTable OBJECT-TYPE SYNTAX SEQUENCE OF RptrPortGrpHwTrapEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of trap enable/disable at the port group level. Disable here is equivalent to disable for each port in the port group." ::= { rptrPortGrpHwTrapSet 1 } rptrPortGrpHwTrapEntry OBJECT-TYPE SYNTAX RptrPortGrpHwTrapEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Individual trap entries for port group enable/disable." INDEX { rptrPortGrpHwTrapSetGrpId } ::= { rptrPortGrpHwTrapTable 1 } RptrPortGrpHwTrapEntry ::= SEQUENCE { rptrPortGrpHwTrapSetGrpId INTEGER, rptrPortGrpHwTrapSetLink INTEGER, rptrPortGrpHwTrapSetSeg INTEGER } rptrPortGrpHwTrapSetGrpId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port group for which the information in this table pertains." ::= { rptrPortGrpHwTrapEntry 1 } rptrPortGrpHwTrapSetLink OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2), other(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Enables and disables link traps for the specified port group. Setting a value of disable(1) is equivalent to setting all instances of rptrPortHwTrapSetLink to a value of disable(1). Setting a value of enable(2) is equivalent to setting all instances of rptrPortHwTrapSetLink to a value of disable(2). Setting a value of other(3) is not allowed. This object will read with the value of disable(1) if all instances of rptrPortHwTrapSetLink for this port group are currently set to a value of disable(1). This object will read with the value of enable(2) if all instances of rptrPortHwTrapSetLink for this port group are currently set to a value of enable(2). This object will read with the value of other(3) if all instances of rptrPortHwTrapSetLink for this port group are not currently set to a value the same value." ::= { rptrPortGrpHwTrapEntry 2 } rptrPortGrpHwTrapSetSeg OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2), other(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Enables and disables segmentation traps for the specified port group. Setting a value of disable(1) is equivalent to setting all instances of rptrPortHwTrapSetSeg to a value of disable(1). Setting a value of enable(2) is equivalent to setting all instances of rptrPortHwTrapSetSeg to a value of disable(2). Setting a value of other(3) is not allowed. This object will read with the value of disable(1) if all instances of rptrPortHwTrapSetSeg for this port group are currently set to a value of disable(1). This object will read with the value of enable(2) if all instances of rptrPortHwTrapSetSeg for this port group are currently set to a value of enable(2). This object will read with the value of other(3) if all instances of rptrPortHwTrapSetSeg for this port group are not currently set to a value the same value." ::= { rptrPortGrpHwTrapEntry 3 } rptrPortGrpSaTrapTable OBJECT-TYPE SYNTAX SEQUENCE OF RptrPortGrpSaTrapEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of trap enable/disable at the port group level. Disable here is equivalent to disable for each port in the port group." ::= { rptrPortGrpSaTrapSet 1 } rptrPortGrpSaTrapEntry OBJECT-TYPE SYNTAX RptrPortGrpSaTrapEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Individual trap entries for port group enable/disable." INDEX { rptrPortGrpSaTrapSetGrpId } ::= { rptrPortGrpSaTrapTable 1 } RptrPortGrpSaTrapEntry ::= SEQUENCE { rptrPortGrpSaTrapSetGrpId INTEGER, rptrPortGrpSaTrapSetSrcaddr INTEGER } rptrPortGrpSaTrapSetGrpId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port group for which the information in this table pertains." ::= { rptrPortGrpSaTrapEntry 1 } rptrPortGrpSaTrapSetSrcaddr OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2), other(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Enables and disables source address traps for the specified port group. Setting a value of disable(1) is equivalent to setting all instances of rtprPortSaTrapSetSrcaddr to a value of disable(1). Setting a value of enable(2) is equivalent to setting all instances of rtprPortSaTrapSetSrcaddr to a value of disable(2). Setting a value of other(3) is not allowed. This object will read with the value of disable(1) if all instances of rptrPortSaTrapSetSrcaddr for this port group are currently set to a value of disable(1). This object will read with the value of enable(2) if all instances of rptrPortSaTrapSetSrcaddr for this port group are currently set to a value of enable(2). This object will read with the value of other(3) if all instances of rptrPortSaTrapSetSrcaddr for this port group are not currently set to a value the same value." ::= { rptrPortGrpSaTrapEntry 2 } rptrPortGrpSrcAddrLockTable OBJECT-TYPE SYNTAX SEQUENCE OF RptrPortGrpSrcAddrLockEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table defines the status of the port group source address security locks." ::= { rptrPortGroup 6 } rptrPortGrpSrcAddrLockEntry OBJECT-TYPE SYNTAX RptrPortGrpSrcAddrLockEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "DeDefines a status of a particular port group security lock." INDEX { rptrPortGrpSrcAddrLockGrpId } ::= { rptrPortGrpSrcAddrLockTable 1 } RptrPortGrpSrcAddrLockEntry ::= SEQUENCE { rptrPortGrpSrcAddrLockGrpId INTEGER, rptrPortGrpSrcAddrLock INTEGER, rptrPortGrpSASecuritySecureState INTEGER, rptrPortGrpSASecurityLearnState INTEGER, rptrPortGrpSASecurityLearnMode INTEGER } rptrPortGrpSrcAddrLockGrpId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Defines a particular port group for which this source address security lock information pertains." ::= { rptrPortGrpSrcAddrLockEntry 1 } rptrPortGrpSrcAddrLock OBJECT-TYPE SYNTAX INTEGER { unlock(1), lock(2), portMisMatch(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Allows setting of the security lock status for this port group. unlock(1) - Unlocks the source address lock this group, lock(2) - Locks the source address for this group, Setting a value of portMisMatch(3) is invalid. A value of portMisMatch(3) reflects that not all ports are at the same value." ::= { rptrPortGrpSrcAddrLockEntry 2 } rptrPortGrpSASecuritySecureState OBJECT-TYPE SYNTAX INTEGER { secure(1), nonSecure(2), portMisMatch(3) } ACCESS read-only STATUS mandatory DESCRIPTION "The state of the source addressing security for this port group. Ports on the port group that are secure(1), can be locked in order to enable security. When a value of nonSecure(2) is returned ports cannot be locked. Setting a value of portMisMatch(3) is invalid. A value of portMisMatch(3) reflects that not all ports are at the same value." ::= { rptrPortGrpSrcAddrLockEntry 3 } rptrPortGrpSASecurityLearnState OBJECT-TYPE SYNTAX INTEGER { learn(1), noLearn(2), portMisMatch(3) } ACCESS read-write STATUS mandatory DESCRIPTION "The learn state of source addressing security for this port group. This object will only be applied to ports that are unlocked. If set to learn(1), all addresses are deleted on the port and learning begins once again. If it is set to noLearn(2), learning stops on the port. Setting a value of portMisMatch(3) is invalid. A value of portMisMatch(3) reflects that not all ports are at the same value." ::= { rptrPortGrpSrcAddrLockEntry 4 } rptrPortGrpSASecurityLearnMode OBJECT-TYPE SYNTAX INTEGER { oneTime(1), continuous(2), portMisMatch(3) } ACCESS read-write STATUS mandatory DESCRIPTION "The learn mode of source addressing security port group. If set to oneTime(1), each port is capable of learning two addresses and securing on both destination and source addresses once they are locked. If set to continuous(2), all addresses are initially deleted and each port continuously replaces the existing secure source address with latest source address it sees. Setting a value of portMisMatch(3) is invalid. A value of portMisMatch(3) reflects that not all ports are at the same value." ::= { rptrPortGrpSrcAddrLockEntry 5 } -- Repeater Port Node -- The following branch in the repeater MIB tree pertains to individual -- repeater ports rptrPort OBJECT IDENTIFIER ::= { repeaterrev4 3 } -- Repeater Port Management Object Definitions -- This section defines a table of Port Management objects under -- the Repeater node. The implementation of this group is optional, -- but within the group all of the elements are mandatory. rptrPortMgmtTable OBJECT-TYPE SYNTAX SEQUENCE OF RptrPortMgmtEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of port management objects for this repeater node." ::= { rptrPort 1 } rptrPortMgmtEntry OBJECT-TYPE SYNTAX RptrPortMgmtEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing objects pertaining to port management for a port." INDEX { rptrPortMgmtPortGrpId, rptrPortMgmtPortId } ::= { rptrPortMgmtTable 1 } RptrPortMgmtEntry ::= SEQUENCE { rptrPortMgmtPortId INTEGER, rptrPortMgmtPortGrpId INTEGER, rptrPortMgmtName DisplayString, rptrPortMgmtAdminState INTEGER, rptrPortMgmtOperState INTEGER, rptrPortMgmtPortType OBJECT IDENTIFIER } rptrPortMgmtPortId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port for which the information in this table pertains." ::= { rptrPortMgmtEntry 1 } rptrPortMgmtPortGrpId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port group for which the information in this table pertains." ::= { rptrPortMgmtEntry 2 } rptrPortMgmtName OBJECT-TYPE SYNTAX DisplayString (SIZE(20)) ACCESS read-write STATUS mandatory DESCRIPTION "Sets/Gets an ASCII name assigned to this port." ::= { rptrPortMgmtEntry 3 } rptrPortMgmtAdminState OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Setting this object to Enable will cause port to be enabled. Setting this object to Disable will cause the port to be disabled. When read this object will return the state of the object per the last request." ::= { rptrPortMgmtEntry 4 } rptrPortMgmtOperState OBJECT-TYPE SYNTAX INTEGER { notOperational(1), operational(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Get port operational status." ::= { rptrPortMgmtEntry 5 } rptrPortMgmtPortType OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS mandatory DESCRIPTION "Uniquely defines the repeater port type. A authoritative identification for a port type. By convention, this value is allocated within the SMI enterprises subtree (1.3.6.1.4.1), and provides an easy and unambiguous means to determine the type of repeater port." ::= { rptrPortMgmtEntry 6 } -- Repeater Port Statistical Object Definitions rptrPortStats OBJECT IDENTIFIER ::= { rptrPort 2 } -- Repeater Port Packet Statistical Object Definitions -- This section defines a table of Port Packet Statistical objects -- under the Repeater node. The implementation of this group is optional, -- but within the group all of the elements are mandatory. rptrPortPktStatsTbl OBJECT-TYPE SYNTAX SEQUENCE OF RptrPortPktStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Provides repeater port packet statistics." ::= { rptrPortStats 1 } rptrPortPktStatsEntry OBJECT-TYPE SYNTAX RptrPortPktStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Provides basic statistics for a specific port." INDEX { rptrPortPktStatsPortGrpId, rptrPortPktStatsPortId } ::= { rptrPortPktStatsTbl 1 } RptrPortPktStatsEntry ::= SEQUENCE { rptrPortPktStatsPortId INTEGER, rptrPortPktStatsPortGrpId INTEGER, rptrPortPktStatsPackets Counter, rptrPortPktStatsBytes Counter, rptrPortPktStatsColls Counter, rptrPortPktStatsErrors Counter, rptrPortPktStatsAlign Counter, rptrPortPktStatsCRC Counter, rptrPortPktStatsOOW Counter, rptrPortPktStatsBroadcasts Counter, rptrPortPktStatsMulticasts Counter } rptrPortPktStatsPortId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port for which the information in this table pertains." ::= { rptrPortPktStatsEntry 1 } rptrPortPktStatsPortGrpId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port group for which the information in this table pertains." ::= { rptrPortPktStatsEntry 2 } rptrPortPktStatsPackets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this port's total received packets." ::= { rptrPortPktStatsEntry 3 } rptrPortPktStatsBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this port's total received bytes." ::= { rptrPortPktStatsEntry 4 } rptrPortPktStatsColls OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this port's total collisions." ::= { rptrPortPktStatsEntry 5 } rptrPortPktStatsErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this port's total errors." ::= { rptrPortPktStatsEntry 6 } rptrPortPktStatsAlign OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this port's total frame alignment errors." ::= { rptrPortPktStatsEntry 7 } rptrPortPktStatsCRC OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this port's total CRC errors." ::= { rptrPortPktStatsEntry 8 } rptrPortPktStatsOOW OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this port's total out-of-window collisions." ::= { rptrPortPktStatsEntry 9 } rptrPortPktStatsBroadcasts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this port's total received broadcast packets." ::= { rptrPortPktStatsEntry 10 } rptrPortPktStatsMulticasts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this port's total received multicast packets." ::= { rptrPortPktStatsEntry 11 } -- Repeater Port Protocol Statistical Object Definitions -- This section defines a table of Port Protocol Statistical -- objects under the Repeater node. The implementation of this -- group is optional, but within the group all of the elements -- are mandatory. rptrPortProtocolTbl OBJECT-TYPE SYNTAX SEQUENCE OF RptrPortProtocolEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Provides statistics about the protocols seen by the different ports." ::= { rptrPortStats 2 } rptrPortProtocolEntry OBJECT-TYPE SYNTAX RptrPortProtocolEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing objects pertaining to statistics about protocols seen by different ports." INDEX { rptrPortProtocolPortGrpId, rptrPortProtocolPortId } ::= { rptrPortProtocolTbl 1 } RptrPortProtocolEntry ::= SEQUENCE { rptrPortProtocolPortId INTEGER, rptrPortProtocolPortGrpId INTEGER, rptrPortProtocolOSI Counter, rptrPortProtocolNovell Counter, rptrPortProtocolBanyan Counter, rptrPortProtocolDECNet Counter, rptrPortProtocolXNS Counter, rptrPortProtocolIP Counter, rptrPortProtocolCtron Counter, rptrPortProtocolAppletalk Counter, rptrPortProtocolOther Counter } rptrPortProtocolPortId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port for which the information in this table pertains." ::= { rptrPortProtocolEntry 1 } rptrPortProtocolPortGrpId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port group for which the information in this table pertains." ::= { rptrPortProtocolEntry 2 } rptrPortProtocolOSI OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this port's total received OSI protocol packets." ::= { rptrPortProtocolEntry 3 } rptrPortProtocolNovell OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this port's total received Novell protocol packets." ::= { rptrPortProtocolEntry 4 } rptrPortProtocolBanyan OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this port's total received Banyan protocol packets." ::= { rptrPortProtocolEntry 5 } rptrPortProtocolDECNet OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this port's total received DECNet protocol packets." ::= { rptrPortProtocolEntry 6 } rptrPortProtocolXNS OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this port's total received XNS protocol packets." ::= { rptrPortProtocolEntry 7 } rptrPortProtocolIP OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this port's total received TCP/IP protocol packets." ::= { rptrPortProtocolEntry 8 } rptrPortProtocolCtron OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this port's total received CTRON Management protocol packets." ::= { rptrPortProtocolEntry 9 } rptrPortProtocolAppletalk OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this port's total received Appletalk protocol packets." ::= { rptrPortProtocolEntry 10 } rptrPortProtocolOther OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this port's total received unknown protocol packets." ::= { rptrPortProtocolEntry 11 } -- Repeater Port Frame Size Statistical Object Definitions -- This section defines a table of Port Frame Size Statistical objects -- under the Repeater node. The implementation of this group is optional, -- but within the group all of the elements are mandatory. rptrPortFrameSzTbl OBJECT-TYPE SYNTAX SEQUENCE OF RptrPortFrameSzEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Provides repeater port frame size statistics." ::= { rptrPortStats 3 } rptrPortFrameSzEntry OBJECT-TYPE SYNTAX RptrPortFrameSzEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Describes a set of frame size statistics for a specific port." INDEX { rptrPortFrameSzPortGrpId, rptrPortFrameSzPortId } ::= { rptrPortFrameSzTbl 1 } RptrPortFrameSzEntry ::= SEQUENCE { rptrPortFrameSzPortId INTEGER, rptrPortFrameSzPortGrpId INTEGER, rptrPortFrameSzRunt Counter, rptrPortFrameSz64To127 Counter, rptrPortFrameSz128To255 Counter, rptrPortFrameSz256To511 Counter, rptrPortFrameSz512To1023 Counter, rptrPortFrameSz1024To1518 Counter, rptrPortFrameSzGiant Counter } rptrPortFrameSzPortId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port for which the information in this table pertains." ::= { rptrPortFrameSzEntry 1 } rptrPortFrameSzPortGrpId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port group for which the information in this table pertains." ::= { rptrPortFrameSzEntry 2 } rptrPortFrameSzRunt OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this port's total received packets of size less than 64 bytes." ::= { rptrPortFrameSzEntry 3 } rptrPortFrameSz64To127 OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this port's total received packets of size between 64 and 127 bytes." ::= { rptrPortFrameSzEntry 4 } rptrPortFrameSz128To255 OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this port's total received packets of size between 128 and 255 bytes." ::= { rptrPortFrameSzEntry 5 } rptrPortFrameSz256To511 OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this port's total received packets of size between 256 and 511 bytes." ::= { rptrPortFrameSzEntry 6 } rptrPortFrameSz512To1023 OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this port's total received packets of size between 512 and 1023 bytes." ::= { rptrPortFrameSzEntry 7 } rptrPortFrameSz1024To1518 OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this port's total received packets of size between 1024 and 1518 bytes." ::= { rptrPortFrameSzEntry 8 } rptrPortFrameSzGiant OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Get this port's total received packets of size greater than 1518 bytes." ::= { rptrPortFrameSzEntry 9 } -- Repeater Port Alarm Object Definitions -- This section defines a table of Port Alarm objects under the -- Repeater node. The implementation of this group is optional, -- but within the group all of the elements are mandatory. rptrPortAlarmTable OBJECT-TYPE SYNTAX SEQUENCE OF RptrPortAlarmEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of port alarm objects for this repeater node." ::= { rptrPort 3 } rptrPortAlarmEntry OBJECT-TYPE SYNTAX RptrPortAlarmEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing objects pertaining to port alarm objects for a port group." INDEX { rptrPortAlarmPortGrpId, rptrPortAlarmPortId } ::= { rptrPortAlarmTable 1 } RptrPortAlarmEntry ::= SEQUENCE { rptrPortAlarmPortId INTEGER, rptrPortAlarmPortGrpId INTEGER, rptrPortAlarmTrafEnable INTEGER, rptrPortAlarmTrafThreshold INTEGER, rptrPortAlarmTrafPortDisable INTEGER, rptrPortAlarmCollEnable INTEGER, rptrPortAlarmCollThreshold INTEGER, rptrPortAlarmCollPortDisable INTEGER, rptrPortAlarmErrEnable INTEGER, rptrPortAlarmErrThreshold INTEGER, rptrPortAlarmErrSource INTEGER, rptrPortAlarmErrPortDisable INTEGER, rptrPortAlarmBroadEnable INTEGER, rptrPortAlarmBroadThreshold INTEGER, rptrPortAlarmBroadPortDisable INTEGER } rptrPortAlarmPortId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port for which the information in this table pertains." ::= { rptrPortAlarmEntry 1 } rptrPortAlarmPortGrpId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port group for which the information in this table pertains." ::= { rptrPortAlarmEntry 2 } rptrPortAlarmTrafEnable OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Get returns whether traffic alarms are enabled/disabled. Set allows for enabling/disabling of traffic alarms." ::= { rptrPortAlarmEntry 3 } rptrPortAlarmTrafThreshold OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The maximum number of packets that will be allowed before an alarm is generated." ::= { rptrPortAlarmEntry 4 } rptrPortAlarmTrafPortDisable OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Set will permit a port to be disabled on a traffic alarm condition. Get will show whether the port disabling is allowed or not." ::= { rptrPortAlarmEntry 5 } rptrPortAlarmCollEnable OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Get returns whether collision alarms are enabled/disabled. Set allows for enabling/disabling of collision alarms." ::= { rptrPortAlarmEntry 6 } rptrPortAlarmCollThreshold OBJECT-TYPE SYNTAX INTEGER (1..999999) ACCESS read-write STATUS mandatory DESCRIPTION "The collision threshold is the maximum number of collisions within the time base that will be allowed before an alaram is generated." ::= { rptrPortAlarmEntry 7 } rptrPortAlarmCollPortDisable OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Set will permit a port to be disabled on a collision alarm condition. Get will show whether the port disabling is allowed or not." ::= { rptrPortAlarmEntry 8 } rptrPortAlarmErrEnable OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Get returns whether error alarms are enabled/disabled. Set allows for enabling/disabling of error alarms." ::= { rptrPortAlarmEntry 9 } rptrPortAlarmErrThreshold OBJECT-TYPE SYNTAX INTEGER (1..100) ACCESS read-write STATUS mandatory DESCRIPTION "Get/Set the percentage of errors per good packet within the timebase that will cause an alarm." ::= { rptrPortAlarmEntry 10 } rptrPortAlarmErrSource OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Get/Set a bit encoded map of which errors to include in the error sum, as follows: CRC_errors - Bit 0 - Least Significant Bit runts - Bit 1 OOW_colls - Bit 2 align_errs - Bit 3 undefined - Bit 4 Giants - Bit 5" ::= { rptrPortAlarmEntry 11 } rptrPortAlarmErrPortDisable OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Set will permit a port to be disabled on an error alarm condition. Get will show whether the port disabling is allowed or not." ::= { rptrPortAlarmEntry 12 } rptrPortAlarmBroadEnable OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Get returns whether broadcast alarms are enabled/disabled. Set allows for enabling/disabling of broadcast alarms." ::= { rptrPortAlarmEntry 13 } rptrPortAlarmBroadThreshold OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The broadcase threshold represents the maximum number of broadcasts that are allowed during the time base before an alarm is generated." ::= { rptrPortAlarmEntry 14 } rptrPortAlarmBroadPortDisable OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Set will permit a port to be disabled on a broadcast alarm condition. Get will show whether the port disabling is allowed or not." ::= { rptrPortAlarmEntry 15 } -- Repeater Port Redundancy Object Definitions -- This section defines a table of Port Redundancy objects under the -- Repeater node. This group of objects may be implemented only if -- the entire set of redundancy object groups have been implemented. rptrPortRedundTable OBJECT-TYPE SYNTAX SEQUENCE OF RptrPortRedundEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of port redundancy objects for this repeater node." ::= { rptrPort 4 } rptrPortRedundEntry OBJECT-TYPE SYNTAX RptrPortRedundEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing objects pertaining to port redundancy for a port group." INDEX { rptrPortRedundPortGrpId, rptrPortRedundPortId } ::= { rptrPortRedundTable 1 } RptrPortRedundEntry ::= SEQUENCE { rptrPortRedundPortId INTEGER, rptrPortRedundPortGrpId INTEGER, rptrPortRedundCrctNum INTEGER, rptrPortRedundType INTEGER, rptrPortRedundStatus INTEGER } rptrPortRedundPortId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port for which the information in this table pertains." ::= { rptrPortRedundEntry 1 } rptrPortRedundPortGrpId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port group for which the information in this table pertains." ::= { rptrPortRedundEntry 2 } rptrPortRedundCrctNum OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Get/Set redundant circuit number of redundant circuit that port is or is to be associated with." ::= { rptrPortRedundEntry 3 } rptrPortRedundType OBJECT-TYPE SYNTAX INTEGER { notUsed(1), primary(2), backup(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Get/Set redundant port type." ::= { rptrPortRedundEntry 4 } rptrPortRedundStatus OBJECT-TYPE SYNTAX INTEGER { notUsed(1), active(2), inactive(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Get/Set redundant port status." ::= { rptrPortRedundEntry 5 } -- Repeater Port Source Address Object Definitions -- This section defines a table of Port Source Address -- objects under the Repeater node. This group of objects -- may be implemented only if the entire set of this group -- has been implemented. rptrPortSrcAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF RptrPortSrcAddrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of port source address objects for this repeater node." ::= { rptrPort 5 } rptrPortSrcAddrEntry OBJECT-TYPE SYNTAX RptrPortSrcAddrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing objects pertaining to port source address objects for a port group." INDEX { rptrPortSrcAddrPortGrpId, rptrPortSrcAddrPortId } ::= { rptrPortSrcAddrTable 1 } RptrPortSrcAddrEntry ::= SEQUENCE { rptrPortSrcAddrPortId INTEGER, rptrPortSrcAddrPortGrpId INTEGER, rptrPortSrcAddrTopoState INTEGER, rptrPortSrcAddrForceTrunk INTEGER, rptrPortSrcAddrActiveUsers INTEGER } rptrPortSrcAddrPortId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port for which the information in this table pertains." ::= { rptrPortSrcAddrEntry 1 } rptrPortSrcAddrPortGrpId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port group for which the information in this table pertains." ::= { rptrPortSrcAddrEntry 2 } rptrPortSrcAddrTopoState OBJECT-TYPE SYNTAX INTEGER { station(1), trunk(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Returns the topological state of the port." ::= { rptrPortSrcAddrEntry 3 } rptrPortSrcAddrForceTrunk OBJECT-TYPE SYNTAX INTEGER { noForce(1), force(2) } ACCESS read-write STATUS mandatory DESCRIPTION "When this object is set to Force it causes the port to be placed into a Trunk topological state whether the network traffic would warrant such a state or not. When this object is set to NoForce it allows the port to assume the topological state it would naturally assume based on the network activity across it. When read this object reports the current setting." ::= { rptrPortSrcAddrEntry 4 } rptrPortSrcAddrActiveUsers OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns the total number of active users seen by this port." ::= { rptrPortSrcAddrEntry 5 } -- Repeater Port Source Address List Object Definitions -- This section defines a table of Port Source Address List -- objects under the Repeater node. This group may only be -- implemented if the entire set of source addressing -- object groups have been implemented. rptrPortSrcAddrListTable OBJECT-TYPE SYNTAX SEQUENCE OF RptrPortSrcAddrListEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table provides information about the source addresses that have been seen by the differnt ports." ::= { rptrPort 6 } rptrPortSrcAddrListEntry OBJECT-TYPE SYNTAX RptrPortSrcAddrListEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A specific source address that has been seen" INDEX { rptrPortSrcAddrListPortGrpId, rptrPortSrcAddrListPortId, rptrPortSrcAddrListId } ::= { rptrPortSrcAddrListTable 1 } RptrPortSrcAddrListEntry ::= SEQUENCE { rptrPortSrcAddrListId INTEGER, rptrPortSrcAddrListPortId INTEGER, rptrPortSrcAddrListPortGrpId INTEGER, rptrPortSrcAddrAddressList OCTET STRING } rptrPortSrcAddrListId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index associated with the number of address to be returned." ::= { rptrPortSrcAddrListEntry 1 } rptrPortSrcAddrListPortId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port for which the information in this table pertains." ::= { rptrPortSrcAddrListEntry 2 } rptrPortSrcAddrListPortGrpId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port group for which the information in this table pertains." ::= { rptrPortSrcAddrListEntry 3 } rptrPortSrcAddrAddressList OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "Returns a source address seen on this port." ::= { rptrPortSrcAddrListEntry 4 } -- Repeater Port Hardware List Object Definitions -- This section defines a table of Hardware objects under the port node. -- This group may only be implemented if the entire set of source addressing -- object groups have been implemented. rptrPortHardwareTable OBJECT-TYPE SYNTAX SEQUENCE OF RptrPortHardwareEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of port hardware objects for this repeater port." ::= { rptrPort 7 } rptrPortHardwareEntry OBJECT-TYPE SYNTAX RptrPortHardwareEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing objects pertaining to port hardware for a hardware port group." INDEX { rptrPortHardwarePortGrpId, rptrPortHardwarePortId } ::= { rptrPortHardwareTable 1 } RptrPortHardwareEntry ::= SEQUENCE { rptrPortHardwarePortId INTEGER, rptrPortHardwarePortGrpId INTEGER, rptrPortHardwareSegStatus INTEGER, rptrPortHardwareLinkStatus INTEGER } rptrPortHardwarePortId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port for which the information in this table pertains." ::= { rptrPortHardwareEntry 1 } rptrPortHardwarePortGrpId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port group for which the information in this table pertains." ::= { rptrPortHardwareEntry 2 } rptrPortHardwareSegStatus OBJECT-TYPE SYNTAX INTEGER { notSegmented(1), segmented(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Returns port segmentation status." ::= { rptrPortHardwareEntry 3 } rptrPortHardwareLinkStatus OBJECT-TYPE SYNTAX INTEGER { notLinked(1), linked(2), notApplicable(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Returns port link status." ::= { rptrPortHardwareEntry 4 } -- port level enable and disables rptrPortTrap OBJECT IDENTIFIER ::= { rptrPort 8 } rptrPortHwTrapSet OBJECT IDENTIFIER ::= { rptrPortTrap 1 } rptrPortSaTrapSet OBJECT IDENTIFIER ::= { rptrPortTrap 2 } rptrPortHwTrapTable OBJECT-TYPE SYNTAX SEQUENCE OF RptrPortHwTrapEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of trap enable/disable at the port level." ::= { rptrPortHwTrapSet 1 } rptrPortHwTrapEntry OBJECT-TYPE SYNTAX RptrPortHwTrapEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Individual trap entries for port group enable/disable." INDEX { rptrPortHwTrapSetPortGrpId, rptrPortHwTrapSetPortId } ::= { rptrPortHwTrapTable 1 } RptrPortHwTrapEntry ::= SEQUENCE { rptrPortHwTrapSetPortId INTEGER, rptrPortHwTrapSetPortGrpId INTEGER, rptrPortHwTrapSetLink INTEGER, rptrPortHwTrapSetSeg INTEGER } rptrPortHwTrapSetPortId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port for which the information in this table pertains." ::= { rptrPortHwTrapEntry 1 } rptrPortHwTrapSetPortGrpId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port group for which the information in this table pertains." ::= { rptrPortHwTrapEntry 2 } rptrPortHwTrapSetLink OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enables and disables link traps for this port." ::= { rptrPortHwTrapEntry 3 } rptrPortHwTrapSetSeg OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enables and disables segmentation traps for this port." ::= { rptrPortHwTrapEntry 4 } rptrPortSaTrapTable OBJECT-TYPE SYNTAX SEQUENCE OF RptrPortSaTrapEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of trap enable/disable at the port level" ::= { rptrPortSaTrapSet 1 } rptrPortSaTrapEntry OBJECT-TYPE SYNTAX RptrPortSaTrapEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Individual trap entries for port group enable/disable." INDEX { rptrPortSaTrapSetPortGrpId, rptrPortSaTrapSetPortId } ::= { rptrPortSaTrapTable 1 } RptrPortSaTrapEntry ::= SEQUENCE { rptrPortSaTrapSetPortId INTEGER, rptrPortSaTrapSetPortGrpId INTEGER, rptrPortSaTrapSetSrcaddr INTEGER } rptrPortSaTrapSetPortId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port for which the information in this table pertains." ::= { rptrPortSaTrapEntry 1 } rptrPortSaTrapSetPortGrpId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port group for which the information in this table pertains." ::= { rptrPortSaTrapEntry 2 } rptrPortSaTrapSetSrcaddr OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enables and disables source address traps for this port." ::= { rptrPortSaTrapEntry 3 } -- Port Source address lock section rptrPortSecurity OBJECT IDENTIFIER ::= { rptrPort 9 } rptrPortSecurityTable OBJECT-TYPE SYNTAX SEQUENCE OF RptrPortSecurityEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table defines status of the source lock security." ::= { rptrPortSecurity 1 } rptrPortSecurityEntry OBJECT-TYPE SYNTAX RptrPortSecurityEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Defines lock status for this particular entry." INDEX { rptrPortSecurityPortGrpId, rptrPortSecurityPortId } ::= { rptrPortSecurityTable 1 } RptrPortSecurityEntry ::= SEQUENCE { rptrPortSecurityPortGrpId INTEGER, rptrPortSecurityPortId INTEGER, rptrPortSecurityLockStatus INTEGER, rptrPortSecurityLockAddAddress OCTET STRING, rptrPortSecurityLockDelAddress OCTET STRING, rptrPortSecurityDisableOnViolation INTEGER, rptrPortSecurityFullSecEnabled INTEGER, rptrPortSecuritySecureState INTEGER, rptrPortSecurityForceNonSecure INTEGER, rptrPortSecurityLearnState INTEGER, rptrPortSecurityLearnMode INTEGER } rptrPortSecurityPortGrpId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION " The port Group ID for which this source address lock entry pertains." ::= { rptrPortSecurityEntry 1 } rptrPortSecurityPortId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The port ID for which this source address lock entry pertains." ::= { rptrPortSecurityEntry 2 } rptrPortSecurityLockStatus OBJECT-TYPE SYNTAX INTEGER { unlock(1), lock(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Defines the lock status for this particular port entry." ::= { rptrPortSecurityEntry 3 } rptrPortSecurityLockAddAddress OBJECT-TYPE SYNTAX OCTET STRING (SIZE(6)) ACCESS read-write STATUS mandatory DESCRIPTION "Setting a value to this object will cause a new entry to be added to the rptrPortSecurityListTable. When read this object will display an OCTET STRING of SIZE 6 with each octet containing a 0. In general it is possible to add addresses at anytime. However there are several instances where the firmware and or hardware can not support the operation. In these instances an error will be returned if a addition is attempted." ::= { rptrPortSecurityEntry 4 } rptrPortSecurityLockDelAddress OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION "Setting a value to this object will cause corresponding entry in the rptrPortSecurityListTable to be deleted. When read this object returns an OCTET STRING of length 6 with each octet having the value '0'. In general it is possible to delete locked addresses at any time. however there are instances where it is not supported in which case an error will be returned." ::= { rptrPortSecurityEntry 5 } rptrPortSecurityDisableOnViolation OBJECT-TYPE SYNTAX INTEGER { noDisable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Designates whether port is disabled if its source address is violated. A source address violation occurs when a address is detected which is not in the source address list for this port. If the port is disabled due to the source address violation it can be enabled by setting rptrPortMgmtAdminState." ::= { rptrPortSecurityEntry 6 } rptrPortSecurityFullSecEnabled OBJECT-TYPE SYNTAX INTEGER { partialSecurity(1), fullSecurity(2) } ACCESS read-write STATUS mandatory DESCRIPTION "A port that is set to full security and is locked will scramble ALL packets, which are not contained in the expected address list, including broadcasts and multicasts. A port that is set to partial security will allow broadcasts and multicasts to repeat unscrambled." ::= { rptrPortSecurityEntry 7 } rptrPortSecuritySecureState OBJECT-TYPE SYNTAX INTEGER { secure(1), nonSecure(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The secure state of the port. If the port is secure(1), it can be locked in order to enable security. A nonSecure(2) port cannot be locked." ::= { rptrPortSecurityEntry 8 } rptrPortSecurityForceNonSecure OBJECT-TYPE SYNTAX INTEGER { noForce(1), forceNonSecure(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The force non-secure state of port. If the port is Forced, Non-Secure via a value of forceNonSecure(2), it is put into a Non-Secure state, in which case it cannot be locked. If a port is not forced noForce(1), then it will take on its natural state, according to the traffic flow on the port." ::= { rptrPortSecurityEntry 9 } rptrPortSecurityLearnState OBJECT-TYPE SYNTAX INTEGER { learn(1), noLearn(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The learn state of the port. This object will only be applied to a port that is unlocked. If set to learn(1), all addresses are deleted on the port and learning begins once again. If it is set to noLearn(2), learning stops on the port." ::= { rptrPortSecurityEntry 10 } rptrPortSecurityLearnMode OBJECT-TYPE SYNTAX INTEGER { oneTime(1), continuous(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The learn mode of the port. If set to oneTime(1), the port is capable of learning two addresses and securing on both destination and source addresses (upon locking port). If set to continuous(2), all addresses are initially deleted and the port continuously replaces the existing secure source address with the latest source address it sees." ::= { rptrPortSecurityEntry 11 } rptrPortSecurityListTable OBJECT-TYPE SYNTAX SEQUENCE OF RptrPortSecurityListEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table defines a list of all source address locks maintained for the specified port." ::= { rptrPortSecurity 2 } rptrPortSecurityListEntry OBJECT-TYPE SYNTAX RptrPortSecurityListEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing objects pertaining to source address locks for a port group." INDEX { rptrPortSecurityListPortGrpId, rptrPortSecurityListPortId, rptrPortSecurityListIndex } ::= { rptrPortSecurityListTable 1 } RptrPortSecurityListEntry ::= SEQUENCE { rptrPortSecurityListPortGrpId INTEGER, rptrPortSecurityListPortId INTEGER, rptrPortSecurityListIndex INTEGER, rptrPortSecurityListAddress OCTET STRING } rptrPortSecurityListPortGrpId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The port group for which this security list entry pertains." ::= { rptrPortSecurityListEntry 1 } rptrPortSecurityListPortId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The port ID for which this source address lock list pertains." ::= { rptrPortSecurityListEntry 2 } rptrPortSecurityListIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A unique index for the source address entries." ::= { rptrPortSecurityListEntry 3 } rptrPortSecurityListAddress OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "Defines the particular source address that has been locked." ::= { rptrPortSecurityListEntry 4 } -- This group is only used for port switching MIMs that support differnt -- port associations. rptrPortAssoc OBJECT IDENTIFIER ::= { repeaterrev4 4 } rptrPortAssocTable OBJECT-TYPE SYNTAX SEQUENCE OF RptrPortAssocEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table defines the port association for those switching MIMs that support this functionality." ::= { rptrPortAssoc 1 } rptrPortAssocEntry OBJECT-TYPE SYNTAX RptrPortAssocEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Describes a particular port association entry." INDEX { rptrPortAssocBoard } ::= { rptrPortAssocTable 1 } RptrPortAssocEntry ::= SEQUENCE { rptrPortAssocBoard INTEGER, rptrPortAssocStatus INTEGER } rptrPortAssocBoard OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The board number for which this port association information pertains." ::= { rptrPortAssocEntry 1 } rptrPortAssocStatus OBJECT-TYPE SYNTAX INTEGER { defaultPort(1), -- Default configuration otherPort(2) -- EPIM } ACCESS read-write STATUS mandatory DESCRIPTION "This object describes the status of the user selectable port. On a TPXMIM34 this is port 13 which may either be an EPIM or default configuration. A value of defaultPort(1) restores the default configuration. A value of otherPort(2) may imply the use of the EPIM connection." ::= { rptrPortAssocEntry 2 } -- TrapTypes -- This section will describe the trap types that the -- repeater section of the EMMe can generate. These are not -- objects, but Object identifers used to indicate the specific -- trap. They are taken from the object space and are thus -- documented here. -- The SNMP protocol provides a mechanism for -- asynchronusly notifying management stations of significant -- changes in the network. This mechanism is the SNMP trap -- message. This document will describe the general format for -- all trap messages that Cabletron products will generate as -- well as the specific traps that the will be generated by the -- EMMe. -- Trap Formats -- The SNMP trap messages are composed of two user -- definable areas: the specific trap type and the VarBindings -- (eg. the interesting information). The specific trap type is -- an INTEGER that is used to determine the specific trap that -- has occurred. The "interesting information" contains a group -- of objects identifiers (OID) and their values that provide -- information about the trap. -- Trap Description -- PortSegmenting -- Specfic Trap Type Code - 0x101 -- When a port goes from operational to segmented, a trap -- will be generated. For these purposes, the port state will -- be sampled every XXX seconds, thus it will be statistically -- possible to miss oscillating circuits. -- The interesting information will include: -- BoardIndex {rptrPortGrpMgmtEntry 1 } -- PortIndex {rptrPortMgmtEntry 1 } -- Trap Description -- PortUnsegementing -- Specfic Trap Type Code - 0x102 -- When it is detected that a previously segmented port -- has gone operational, a trap will be generated. This is -- also sampled, thus a trap may not be generated for each -- transition. -- The interesting information will include: -- BoardIndex {rptrPortGrpMgmtEntry 1 } -- PortIndex {rptrPortMgmtEntry 1 } -- Trap Description -- PortLinkUp -- Specfic Trap Type Code - 0x103 -- This trap will be generated when it is determined that -- MAU has been attached to the MMAC. This is only appropriate -- for MIMs that support the concept of a link state. -- The interesting information will include: -- BoardIndex {rptrPortGrpMgmtEntry 1 } -- PortIndex {rptrPortMgmtEntry 1 } -- Trap Description -- PortLinkDown -- Specfic Trap Type Code - 0x104 -- This trap will be generated when a previously attached -- MAU is removed or powered down. Again, this is only -- appropriate for MIM's that support link state. -- The interesting information will include: -- BoardIndex {rptrPortGrpMgmtEntry 1 } -- PortIndex {rptrPortMgmtEntry 1 } -- Trap Description -- NewSourceAddress -- Specfic Trap Type Code - 0x105 -- This trap will be generated when the MMAC detects the -- existence of a new source address on one of it's ports. -- The interesting information will include: -- BoardIndex {rptrPortGrpMgmtEntry 1 } -- PortIndex {rptrPortMgmtEntry 1 } -- PortSourceAddr {rptrPortSrcAddrListEntry 4 } -- Trap Description -- SourceAddressTimeout -- Specfic Trap Type Code - 0x106 -- This trap will indicate that the MMAC has not detected -- a packet generated by this source address within a certain -- timeout. -- The interesting information will include: -- BoardIndex {rptrPortGrpMgmtEntry 1 } -- PortIndex {rptrPortMgmtEntry 1 } -- PortSourceAddr {rptrPortSrcAddrListEntry 4 } -- Trap Description -- BoardRemoval -- Specfic Trap Type Code - 0x107 -- This trap will be generated when the MMAC detects that -- MIM has been removed. -- The interesting information will include: -- BoardIndex {chSlotEntry 1 } in the -- chassisMib 1.3.6.1.4.1.52.4.1.1.2.5.1.1 -- Trap Description -- boardInsertion -- (also see chBoardInsertion, 0x136) -- Specfic Trap Type Code - 0x108 -- This trap will be generated when the MMAC determines -- that a new board has been inserted. -- The interesting information will include: -- chSlotID -- deviceType -- Trap Description -- ActivePortInRedundantCircuitFailed -- Specfic Trap Type Code - 0x109 -- This trap will be generated when the active port in a -- redundant circuit has failed polling. This will indicate the -- activation of redundancy. -- The interesting information will include: -- BoardIndex {rptrPortGrpMgmtEntry 1 } -- PortIndex {rptrPortMgmtEntry 1 } -- PortRedundCrt {rptrPortRedundEntry 3 } -- Trap Description -- RedundantPortActivated -- Specfic Trap Type Code - 0x10a -- This trap indicates that a new port has been activated -- in a redundant circuit. This does NOT indicate that this -- port is usable, but is being tested. If the port fails the -- above (3.9) trap will be generated. -- The interesting information will include: -- BoardIndex {rptrPortGrpMgmtEntry 1 } -- PortIndex {rptrPortMgmtEntry 1 } -- PortRedundCrt {rptrPortRedundEntry 3 } -- Trap Description -- RedundantPortTestFailed -- Specfic Trap Type Code - 0x10b -- This trap will be generated when the MMAC executes it's -- periodic redundancy diagnostics and finds on of the ports in -- a redundant circuit has failed. This message will not -- indicate that redundancy has been activated, just that the -- port has failed and should be fixed before it is needed. -- The interesting information will include: -- BoardIndex {rptrPortGrpMgmtEntry 1 } -- PortIndex {rptrPortMgmtEntry 1 } -- PortRedundCrt {rptrPortRedundEntry 3 } -- Trap Description -- BoardTrafficThresholdExceeded -- Specfic Trap Type Code - 0x10f -- This trap will be generated when the traffic (good -- packets per time interval) has been exceed for a particular -- MIM. -- The interesting information will include: -- BoardTrafficThreshold {rptrPortGrpAlarmEntry 3 } -- RptrTimebase {rptrAlarms 8 } -- BoardIndex {rptrPortGrpMgmtEntry 1 } -- Trap Description -- BoardErrorThresholdExceeded -- Specfic Trap Type Code - 0x110 -- This trap will be generated when packets of the -- selected error type exceeds a threshold percentage of the -- good packets for a particular interval for a particular MIM. -- This will most likely indicate a bad MIM. -- The interesting information will include: -- BoardErrorThreshold {rptrPortGrpAlarmEntry 9 } -- BoardErrorSource {rptrPortGrpAlarmEntry 10 } -- RptrTimebase {rptrAlarms 8 } -- BoardIndex {rptrPortGrpMgmtEntry 1 } -- Trap Description -- BoardCollisionThresholdExceeded -- Specfic Trap Type Code - 0x111 -- This trap will be generated when collisions exceed a -- threshold percentage of the good packets for a particular -- interval for a particular MIM. -- The interesting information will include: -- BoardCollsThreshold {rptrPortGrpAlarmEntry 6 } -- RptrTimebase {rptrAlarms 8 } -- BoardIndex {rptrPortGrpMgmtEntry 1 } -- Trap Description -- PortTrafficThresholdExceeded -- Specfic Trap Type Code - 0x112 -- This trap will be generated when the traffic (good -- packets per time interval) has been exceed for a particular -- port. -- The interesting information will include: -- PortTrafficThreshold {rptrPortAlarmEntry 4 } -- RptrTimebase {rptrAlarms 8 } -- BoardIndex {rptrPortGrpMgmtEntry 1 } -- PortIndex {rptrPortMgmtEntry 1 } -- Trap Description -- PortErrorThresholdExceeded -- Specfic Trap Type Code - 0x113 -- This trap will be generated when packets of the -- selected error type exceeds a threshold percentage of the -- good packets for a particular interval for a particular -- port. -- The interesting information will include: -- PortErrorThreshold {rptrPortAlarmEntry 10 } -- PortErrorSource {rptrPortAlarmEntry 11 } -- RptrTimebase {rptrAlarms 8 } -- BoardIndex {rptrPortGrpMgmtEntry 1 } -- PortIndex {rptrPortMgmtEntry 1 } -- Trap Description -- PortCollisionThresholdExceeded -- Specfic Trap Type Code - 0x114 -- This trap will be generated when collisions exceed a -- threshold percentage of the good packets for a particular -- interval for a particular port. -- The interesting information will include: -- PortCollsThreshold {rptrPortAlarmEntry 7 } -- RptrTimebase {rptrAlarms 8 } -- BoardIndex {rptrPortGrpMgmtEntry 1 } -- PortIndex {rptrPortMgmtEntry 1 } -- Trap Description -- PortTypeChanged -- Specfic Trap Type Code - 0x115 -- This trap indicates that a port has changed from a -- station port to a link port or vice versa. -- The interesting information is: -- BoardIndex {rptrPortGrpMgmtEntry 1 } -- PortIndex {rptrPortMgmtEntry 1 } -- PortTopologyType {rptrPortSrcAddrEntry 3 } -- Trap Description -- PortSecurityViolation -- Specfic Trap Type Code - 0x117 -- This trap is generated when a source address other than those -- locked to a port is seen. -- The interesting information is: -- BoardIndex {rptrPortGrpMgmtEntry 1 } -- PortIndex {rptrPortMgmtEntry 1 } -- PortSourceAddr {rptrPortSrcAddrListEntry 4 } -- Trap Description -- PortViolationReset -- Specfic Trap Type Code - 0x118 -- This trap is generated when management intervention has -- reset a port after a violation has occurred. -- The interesting information is: -- BoardIndex {rptrPortGrpMgmtEntry 1 } -- PortIndex {rptrPortMgmtEntry 1 } -- Trap Description -- EnvTempWarm -- Specfic Trap Type Code - 0x119 -- This trap is generated when the device detects that the temperature -- within a MIM has reached a WARM condition. -- The interesting information is: -- BoardIndex {chSlotEntry 1 } in the -- chassisMib 1.3.6.1.4.1.52.4.1.1.2.5.1.1 -- Trap Description -- EnvTempHot -- Specfic Trap Type Code - 0x11A -- This trap is generated when the device detects that the temperature -- within a MIM has reached a HOT condition. -- The interesting information is: -- BoardIndex {chSlotEntry 1 } in the -- chassisMib 1.3.6.1.4.1.52.4.1.1.2.5.1.1 -- Trap Description -- EnvTempNormal -- Specfic Trap Type Code - 0x11C -- This trap is generated when the device detects that the temperature -- within a MIM has returned to a NORMAL state. -- The interesting information is: -- BoardIndex {chSlotEntry 1 } in the -- chassisMib 1.3.6.1.4.1.52.4.1.1.2.5.1.1 -- Trap Description -- EnvVoltageLow -- Specfic Trap Type Code - 0x11B -- This trap is generated when a power supply`s voltage is LOW. -- The interesting information is: -- PowerSupply {PowerEntry 1 } in the -- commonMib 1.3.6.1.4.1.52.1.6.1.4.1.1 -- Trap Description -- EnvVoltageNormal -- Specfic Trap Type Code - 0x11D -- This trap is generated when all power supply's voltage -- have returned to a NORMAL state. -- The interesting information is: -- None -- Trap Description -- FanFail -- Specfic Trap Type Code - 0x11E -- This trap is generated when the device detects that the system fans -- have failed. -- The interesting information is: -- None -- Trap Description -- FanNormal -- Specfic Trap Type Code - 0x11F -- This trap is generated when the device detects that the system fans -- have returned to normal. -- The interesting information is: -- None -- Trap Description -- Trap Description -- BoardBroadcastThresholdExceeded -- -- Specific Trap Type Code - 0x121 -- -- This trap is generated when the broadcast packets (per time -- interval) have exceeded the threshold for the given board. -- -- The Interesting Information is: -- board broadcast threshold -- repeater alarm time base -- board number -- -- Trap Description -- PortBroadcastThresholdExceeded -- -- Specific Trap Type Code - 0x122 -- -- This trap is generated when the broadcast packets (per time -- interval) have exceeded the threshold for the given port. -- -- The Interesting Information is: -- port broadcast threshold -- repeater alarm time base -- board number -- port number -- -- SystemVolatgeLow -- Specfic Trap Type Code - 0x125 -- This trap is generated when the device detects that the power -- to the EMMe is low. -- The interesting information is: -- None -- Trap Description -- SystemVolatgeNormal -- Specfic Trap Type Code - 0x126 -- This trap is generated when the device detects that the power -- to the EMMe has returned to normal. -- The interesting information is: -- None -- Trap Description -- EpimRemoval -- Specfic Trap Type Code - 0x127 -- This trap will be generated when it is detected that an EPIM -- has been removed. -- The interesting information will include: -- BoardIndex {rptrPortGrpMgmtEntry 1 } -- PortIndex {rptrPortMgmtEntry 1 } -- Trap Description -- Epiminsertion -- Specfic Trap Type Code - 0x128 -- This trap will be generated when it is detected that an EPIM -- has been inserted. -- The interesting information will include: -- BoardIndex {rptrPortGrpMgmtEntry 1 } -- PortIndex {rptrPortMgmtEntry 1 } -- PortType { rptrPortMgmtEntry 6 } -- Trap Description -- RptrTrafficThresholdExceeded -- Specfic Trap Type Code - 0x129 -- This trap will be generated when the traffic (good -- packets per time interval) has been exceed for a network. -- The interesting information will include: -- RptrTrafficThreshold {rptrAlarms 2 } -- RptrTimebase {rptrAlarms 8 } -- RptrInterfaceNum {rptrMgmt 7 } -- Trap Description -- RptrErrorThresholdExceeded -- Specfic Trap Type Code - 0x130 -- This trap will be generated when packets of the -- selected error type exceeds a threshold percentage of the -- good packets for a particular interval for an entire network. -- The interesting information will include: -- RptrErrorThreshold {rptrAlarms 6 } -- RptrErrorSource {rptrAlarms 7 } -- RptrTimebase {rptrAlarms 8 } -- RptrInterfaceNum {rptrMgmt 7 } -- Trap Description -- RptrCollsionThresholdExceeded -- Specfic Trap Type Code - 0x131 -- This trap will be generated when collisions exceed a -- threshold percentage of the good packets for a particular -- interval for an entire network. -- The interesting information will include: -- RptrCollsThreshold {rptrAlarms 4 } -- RptrTimebase {rptrAlarms 8 } -- RptrInterfaceNum {rptrMgmt 7 } -- Trap Description -- RptrLockSTATUSChanged -- Specfic Trap Type Code - 0x132 -- This trap is generated when the status of the address lock -- changes for a certain network. -- The interesting information is: -- RptrSrcAddrLocked {rptrSrcAddrMgmt 2 } -- RptrInterfaceNum {rptrMgmt 7 } -- Trap Description -- RptrBroadcastThresholdExceeded -- -- Specific Trap Type Code - 0x133 -- -- This trap is generated when the broadcast packets (per time -- interval) have exceeded the threshold for the given repeater. -- -- The Interesting Information is: -- repeater broadcast threshold -- repeater alarm time base -- repeater interface number -- Trap Description -- srcAddressPortGrpLockStatusChange -- This trap is generated when a change to the source address locking -- is detected at the port group level. -- The interesting information is: -- -- { rptrPortGrpMgmtentry 1 } -- { rptrPortGrpSrcAddrEntry 3 } -- Trap code = 0x134 -- Trap Description -- srcAddressPortLockStatusChange -- This trap is generated when a change to the source address locking -- is detected at the port level. -- Interesting information is: -- -- port group { rptrPortGrmtMgmtEntry 1 } -- port { rptrPortMgmtEntry 2 } -- lock status { rptrPortSecurityLockEntry 3 } -- Trap Description -- chBoardInsertion -- (also see boardInsertion, 0x108) -- Specfic Trap Type Code - 0x136 -- This trap will be generated when the MMAC determines -- that a new board has been inserted. -- The interesting information will include: -- chSlotID -- chSlotModuleType END