Nortel-Magellan-Passport-Frf5EpMIB DEFINITIONS ::= BEGIN IMPORTS OBJECT-TYPE FROM RFC-1212 passportMIBs FROM Nortel-Magellan-Passport-UsefulDefinitionsMIB Counter32, RowPointer, DisplayString, StorageType, RowStatus, Integer32, Unsigned32 FROM Nortel-Magellan-Passport-StandardTextualConventionsMIB AsciiString, NonReplicated, HexString, IntegerSequence FROM Nortel-Magellan-Passport-TextualConventionsMIB mcsMgrIndex, mcsMgr FROM Nortel-Magellan-Passport-McsMgrMIB; -- LAST-UPDATED "9706300000Z" -- ORGANIZATION "Nortel" -- CONTACT-INFO " -- Nortel Magellan Network Management -- -- Postal: P.O. Box 5080, Station F -- Ottawa, Ontario -- Canada K2C 3T1 -- -- Email: nm_plm@nt.com" -- DESCRIPTION -- "The module describing the Nortel Magellan Passport -- Frf5Ep Enterprise MIB." frf5EpMIB OBJECT IDENTIFIER ::= { passportMIBs 121 } -- McsMgr Frf5EndPointGroup/n -- The Frf5EpG component contains FRF.5 End Points that share a -- common destination NSAP address, and a list of address prefixes. mcsMgrFrf5EpG OBJECT IDENTIFIER ::= { mcsMgr 14 } mcsMgrFrf5EpGRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF McsMgrFrf5EpGRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of mcsMgrFrf5EpG components." ::= { mcsMgrFrf5EpG 1 } mcsMgrFrf5EpGRowStatusEntry OBJECT-TYPE SYNTAX McsMgrFrf5EpGRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single mcsMgrFrf5EpG component." INDEX { mcsMgrIndex, mcsMgrFrf5EpGIndex } ::= { mcsMgrFrf5EpGRowStatusTable 1 } McsMgrFrf5EpGRowStatusEntry ::= SEQUENCE { mcsMgrFrf5EpGRowStatus RowStatus, mcsMgrFrf5EpGComponentName DisplayString, mcsMgrFrf5EpGStorageType StorageType, mcsMgrFrf5EpGIndex Integer32 } mcsMgrFrf5EpGRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-write STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of mcsMgrFrf5EpG components. These components can be added and deleted." ::= { mcsMgrFrf5EpGRowStatusEntry 1 } mcsMgrFrf5EpGComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { mcsMgrFrf5EpGRowStatusEntry 2 } mcsMgrFrf5EpGStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the mcsMgrFrf5EpG tables." ::= { mcsMgrFrf5EpGRowStatusEntry 4 } mcsMgrFrf5EpGIndex OBJECT-TYPE SYNTAX Integer32 (1..8191) ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the mcsMgrFrf5EpG tables." ::= { mcsMgrFrf5EpGRowStatusEntry 10 } -- McsMgr Frf5EpG/n Address -- This component contains the destination NSAP address used by all -- FRF.5 End Points provisioned under an Frf5EpG. The Address also -- provides the list of address prefixes directed to the end points under -- this group. mcsMgrFrf5EpGAddr OBJECT IDENTIFIER ::= { mcsMgrFrf5EpG 2 } mcsMgrFrf5EpGAddrRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF McsMgrFrf5EpGAddrRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of mcsMgrFrf5EpGAddr components." ::= { mcsMgrFrf5EpGAddr 1 } mcsMgrFrf5EpGAddrRowStatusEntry OBJECT-TYPE SYNTAX McsMgrFrf5EpGAddrRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single mcsMgrFrf5EpGAddr component." INDEX { mcsMgrIndex, mcsMgrFrf5EpGIndex, mcsMgrFrf5EpGAddrIndex } ::= { mcsMgrFrf5EpGAddrRowStatusTable 1 } McsMgrFrf5EpGAddrRowStatusEntry ::= SEQUENCE { mcsMgrFrf5EpGAddrRowStatus RowStatus, mcsMgrFrf5EpGAddrComponentName DisplayString, mcsMgrFrf5EpGAddrStorageType StorageType, mcsMgrFrf5EpGAddrIndex NonReplicated } mcsMgrFrf5EpGAddrRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of mcsMgrFrf5EpGAddr components. These components cannot be added nor deleted." ::= { mcsMgrFrf5EpGAddrRowStatusEntry 1 } mcsMgrFrf5EpGAddrComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { mcsMgrFrf5EpGAddrRowStatusEntry 2 } mcsMgrFrf5EpGAddrStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the mcsMgrFrf5EpGAddr tables." ::= { mcsMgrFrf5EpGAddrRowStatusEntry 4 } mcsMgrFrf5EpGAddrIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the mcsMgrFrf5EpGAddr tables." ::= { mcsMgrFrf5EpGAddrRowStatusEntry 10 } mcsMgrFrf5EpGAddrProvTable OBJECT-TYPE SYNTAX SEQUENCE OF McsMgrFrf5EpGAddrProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the provisionable attributes of the Address component." ::= { mcsMgrFrf5EpGAddr 10 } mcsMgrFrf5EpGAddrProvEntry OBJECT-TYPE SYNTAX McsMgrFrf5EpGAddrProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the mcsMgrFrf5EpGAddrProvTable." INDEX { mcsMgrIndex, mcsMgrFrf5EpGIndex, mcsMgrFrf5EpGAddrIndex } ::= { mcsMgrFrf5EpGAddrProvTable 1 } McsMgrFrf5EpGAddrProvEntry ::= SEQUENCE { mcsMgrFrf5EpGAddrRemoteAddress AsciiString, mcsMgrFrf5EpGAddrCommentText AsciiString } mcsMgrFrf5EpGAddrRemoteAddress OBJECT-TYPE SYNTAX AsciiString (SIZE (0..44)) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the ATM End System Address (AESA) in the ISO NSAP format that is used by each EndPoint under this Frf5EpG to establish a VCC. For example, NSAP ATM address '45000006138292323F000000000020480D002900'." ::= { mcsMgrFrf5EpGAddrProvEntry 1 } mcsMgrFrf5EpGAddrCommentText OBJECT-TYPE SYNTAX AsciiString (SIZE (0..750)) ACCESS read-write STATUS mandatory DESCRIPTION "This optional attribute contains additional textual information to be added by the network operator." DEFVAL { ''H } -- "" ::= { mcsMgrFrf5EpGAddrProvEntry 2 } mcsMgrFrf5EpGAddrAddrPreTable OBJECT-TYPE SYNTAX SEQUENCE OF McsMgrFrf5EpGAddrAddrPreEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute specifies the list of prefixes directed to the EndPoints under this Frf5EndPointGroup. The individual end point is selected for each subconnection on the basis of its supportedTransferPriorities. For example, E.164 prefix 'e.613722', X.121 prefix 'x.302'." ::= { mcsMgrFrf5EpGAddr 362 } mcsMgrFrf5EpGAddrAddrPreEntry OBJECT-TYPE SYNTAX McsMgrFrf5EpGAddrAddrPreEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the mcsMgrFrf5EpGAddrAddrPreTable." INDEX { mcsMgrIndex, mcsMgrFrf5EpGIndex, mcsMgrFrf5EpGAddrIndex, mcsMgrFrf5EpGAddrAddrPreValue } ::= { mcsMgrFrf5EpGAddrAddrPreTable 1 } McsMgrFrf5EpGAddrAddrPreEntry ::= SEQUENCE { mcsMgrFrf5EpGAddrAddrPreValue AsciiString, mcsMgrFrf5EpGAddrAddrPreRowStatus RowStatus } mcsMgrFrf5EpGAddrAddrPreValue OBJECT-TYPE SYNTAX AsciiString (SIZE (3..17)) ACCESS read-write STATUS mandatory DESCRIPTION "This variable represents both the value and the index for the mcsMgrFrf5EpGAddrAddrPreTable." ::= { mcsMgrFrf5EpGAddrAddrPreEntry 1 } mcsMgrFrf5EpGAddrAddrPreRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS write-only STATUS mandatory DESCRIPTION "This variable is used to control the addition and deletion of individual values of the mcsMgrFrf5EpGAddrAddrPreTable." ::= { mcsMgrFrf5EpGAddrAddrPreEntry 2 } -- McsMgr Frf5EpG/n EndPoint/n -- The EndPoint component represents a single ATM VCC that can -- multiplex multiple Frame Relay DLCIs. mcsMgrFrf5EpGEp OBJECT IDENTIFIER ::= { mcsMgrFrf5EpG 3 } mcsMgrFrf5EpGEpRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF McsMgrFrf5EpGEpRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of mcsMgrFrf5EpGEp components." ::= { mcsMgrFrf5EpGEp 1 } mcsMgrFrf5EpGEpRowStatusEntry OBJECT-TYPE SYNTAX McsMgrFrf5EpGEpRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single mcsMgrFrf5EpGEp component." INDEX { mcsMgrIndex, mcsMgrFrf5EpGIndex, mcsMgrFrf5EpGEpIndex } ::= { mcsMgrFrf5EpGEpRowStatusTable 1 } McsMgrFrf5EpGEpRowStatusEntry ::= SEQUENCE { mcsMgrFrf5EpGEpRowStatus RowStatus, mcsMgrFrf5EpGEpComponentName DisplayString, mcsMgrFrf5EpGEpStorageType StorageType, mcsMgrFrf5EpGEpIndex Integer32 } mcsMgrFrf5EpGEpRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-write STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of mcsMgrFrf5EpGEp components. These components can be added and deleted." ::= { mcsMgrFrf5EpGEpRowStatusEntry 1 } mcsMgrFrf5EpGEpComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { mcsMgrFrf5EpGEpRowStatusEntry 2 } mcsMgrFrf5EpGEpStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the mcsMgrFrf5EpGEp tables." ::= { mcsMgrFrf5EpGEpRowStatusEntry 4 } mcsMgrFrf5EpGEpIndex OBJECT-TYPE SYNTAX Integer32 (0..15) ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the mcsMgrFrf5EpGEp tables." ::= { mcsMgrFrf5EpGEpRowStatusEntry 10 } mcsMgrFrf5EpGEpStateTable OBJECT-TYPE SYNTAX SEQUENCE OF McsMgrFrf5EpGEpStateEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the three OSI State attributes and the six OSI Status attributes. The descriptions generically indicate what each attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241- 7001-150, Passport Operations and Maintenance Guide." ::= { mcsMgrFrf5EpGEp 10 } mcsMgrFrf5EpGEpStateEntry OBJECT-TYPE SYNTAX McsMgrFrf5EpGEpStateEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the mcsMgrFrf5EpGEpStateTable." INDEX { mcsMgrIndex, mcsMgrFrf5EpGIndex, mcsMgrFrf5EpGEpIndex } ::= { mcsMgrFrf5EpGEpStateTable 1 } McsMgrFrf5EpGEpStateEntry ::= SEQUENCE { mcsMgrFrf5EpGEpAdminState INTEGER, mcsMgrFrf5EpGEpOperationalState INTEGER, mcsMgrFrf5EpGEpUsageState INTEGER, mcsMgrFrf5EpGEpAvailabilityStatus OCTET STRING, mcsMgrFrf5EpGEpProceduralStatus OCTET STRING, mcsMgrFrf5EpGEpControlStatus OCTET STRING, mcsMgrFrf5EpGEpAlarmStatus OCTET STRING, mcsMgrFrf5EpGEpStandbyStatus INTEGER, mcsMgrFrf5EpGEpUnknownStatus INTEGER } mcsMgrFrf5EpGEpAdminState OBJECT-TYPE SYNTAX INTEGER { locked(0), unlocked(1), shuttingDown(2) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component." DEFVAL { unlocked } ::= { mcsMgrFrf5EpGEpStateEntry 1 } mcsMgrFrf5EpGEpOperationalState OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component." DEFVAL { disabled } ::= { mcsMgrFrf5EpGEpStateEntry 2 } mcsMgrFrf5EpGEpUsageState OBJECT-TYPE SYNTAX INTEGER { idle(0), active(1), busy(2) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component." DEFVAL { idle } ::= { mcsMgrFrf5EpGEpStateEntry 3 } mcsMgrFrf5EpGEpAvailabilityStatus OBJECT-TYPE SYNTAX OCTET STRING (SIZE (2)) ACCESS read-only STATUS mandatory DESCRIPTION "If supported by the component, this attribute indicates the OSI Availability status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value inTest indicates that the resource is undergoing a test procedure. If adminState is locked or shuttingDown, the normal users are precluded from using the resource and controlStatus is reservedForTest. Tests that do not exclude additional users can be present in any operational or administrative state but the reservedForTest condition should not be present. The value failed indicates that the component has an internal fault that prevents it from operating. The operationalState is disabled. The value dependency indicates that the component cannot operate because some other resource on which it depends is unavailable. The operationalState is disabled. The value powerOff indicates the resource requires power to be applied and it is not powered on. The operationalState is disabled. The value offLine indicates the resource requires a routine operation (either manual, automatic, or both) to be performed to place it on-line and make it available for use. The operationalState is disabled. The value offDuty indicates the resource is inactive in accordance with a predetermined time schedule. In the absence of other disabling conditions, the operationalState is enabled or disabled. The value degraded indicates the service provided by the component is degraded in some way, such as in speed or operating capacity. However, the resource remains available for service. The operationalState is enabled. The value notInstalled indicates the resource is not present. The operationalState is disabled. The value logFull is not used. Description of bits: inTest(0) failed(1) powerOff(2) offLine(3) offDuty(4) dependency(5) degraded(6) notInstalled(7) logFull(8)" ::= { mcsMgrFrf5EpGEpStateEntry 4 } mcsMgrFrf5EpGEpProceduralStatus OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) ACCESS read-only STATUS mandatory DESCRIPTION "If supported by the component, this attribute indicates the OSI Procedural status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value initializationRequired indicates (for a resource which doesn't initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState is disabled. The value notInitialized indicates (for a resource which does initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState may be enabled or disabled. The value initializing indicates that initialization has been initiated but is not yet complete. The operationalState may be enabled or disabled. The value reporting indicates the resource has completed some processing operation and is notifying the results. The operationalState is enabled. The value terminating indicates the component is in a termination phase. If the resource doesn't reinitialize autonomously, operationalState is disabled; otherwise it is enabled or disabled. Description of bits: initializationRequired(0) notInitialized(1) initializing(2) reporting(3) terminating(4)" ::= { mcsMgrFrf5EpGEpStateEntry 5 } mcsMgrFrf5EpGEpControlStatus OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) ACCESS read-only STATUS mandatory DESCRIPTION "If supported by the component, this attribute indicates the OSI Control status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value subjectToTest indicates the resource is available but tests may be conducted simultaneously at unpredictable times, which may cause it to exhibit unusual characteristics. The value partOfServicesLocked indicates that part of the service is restricted from users of a resource. The adminState is unlocked. The value reservedForTest indicates that the component is administratively unavailable because it is undergoing a test procedure. The adminState is locked. The value suspended indicates that the service has been administratively suspended. Description of bits: subjectToTest(0) partOfServicesLocked(1) reservedForTest(2) suspended(3)" ::= { mcsMgrFrf5EpGEpStateEntry 6 } mcsMgrFrf5EpGEpAlarmStatus OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) ACCESS read-only STATUS mandatory DESCRIPTION "If supported by the component, this attribute indicates the OSI Alarm status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value underRepair indicates the component is currently being repaired. The operationalState is enabled or disabled. The value critical indicates one or more critical alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value major indicates one or more major alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value minor indicates one or more minor alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value alarmOutstanding generically indicates that an alarm of some severity is outstanding against the component. Description of bits: underRepair(0) critical(1) major(2) minor(3) alarmOutstanding(4)" ::= { mcsMgrFrf5EpGEpStateEntry 7 } mcsMgrFrf5EpGEpStandbyStatus OBJECT-TYPE SYNTAX INTEGER { hotStandby(0), coldStandby(1), providingService(2), notSet(15) } ACCESS read-only STATUS mandatory DESCRIPTION "If supported by the component, this attribute indicates the OSI Standby status of the component. The value notSet indicates that either the attribute is not supported or that none of the status conditions described below are present. Note that this is a non-standard value, used because the original specification indicated this attribute was set-valued and thus, did not provide a value to indicate that none of the other three are applicable. The value hotStandby indicates that the resource is not providing service but will be immediately able to take over the role of the resource to be backed up, without initialization activity, and containing the same information as the resource to be backed up. The value coldStandby indicates the resource is a backup for another resource but will not be immediately able to take over the role of the backed up resource and will require some initialization activity. The value providingService indicates that this component, as a backup resource, is currently backing up another resource." DEFVAL { notSet } ::= { mcsMgrFrf5EpGEpStateEntry 8 } mcsMgrFrf5EpGEpUnknownStatus OBJECT-TYPE SYNTAX INTEGER { false(0), true(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the OSI Unknown status of the component. The value false indicates that all of the other OSI State and Status attribute values can be considered accurate. The value true indicates that the actual state of the component is not known for sure." DEFVAL { false } ::= { mcsMgrFrf5EpGEpStateEntry 9 } mcsMgrFrf5EpGEpOperTable OBJECT-TYPE SYNTAX SEQUENCE OF McsMgrFrf5EpGEpOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the operational attributes for the FRF.5 ATM connection." ::= { mcsMgrFrf5EpGEp 11 } mcsMgrFrf5EpGEpOperEntry OBJECT-TYPE SYNTAX McsMgrFrf5EpGEpOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the mcsMgrFrf5EpGEpOperTable." INDEX { mcsMgrIndex, mcsMgrFrf5EpGIndex, mcsMgrFrf5EpGEpIndex } ::= { mcsMgrFrf5EpGEpOperTable 1 } McsMgrFrf5EpGEpOperEntry ::= SEQUENCE { mcsMgrFrf5EpGEpLastVccClearCause Unsigned32, mcsMgrFrf5EpGEpConnectionTransferPriority Unsigned32, mcsMgrFrf5EpGEpServiceCategory INTEGER, mcsMgrFrf5EpGEpPeakCellRate01 Unsigned32, mcsMgrFrf5EpGEpSustainedCellRate0 Unsigned32, mcsMgrFrf5EpGEpSustainedCellRate01 Unsigned32, mcsMgrFrf5EpGEpMaximumBurstSize0 Unsigned32, mcsMgrFrf5EpGEpMaximumBurstSize01 Unsigned32, mcsMgrFrf5EpGEpAvgFrameSize Unsigned32, mcsMgrFrf5EpGEpTrafficParmConversionPolicy INTEGER, mcsMgrFrf5EpGEpType INTEGER, mcsMgrFrf5EpGEpLastVccCauseDiag HexString } mcsMgrFrf5EpGEpLastVccClearCause OBJECT-TYPE SYNTAX Unsigned32 (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the clear cause value of the last SPVC release message received on the FRF.5 end point Vcc pipe." ::= { mcsMgrFrf5EpGEpOperEntry 4 } mcsMgrFrf5EpGEpConnectionTransferPriority OBJECT-TYPE SYNTAX Unsigned32 (0..15) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the transfer priority used to establish the ATM connection and to multiplex the Frame Relay DLCIs." ::= { mcsMgrFrf5EpGEpOperEntry 5 } mcsMgrFrf5EpGEpServiceCategory OBJECT-TYPE SYNTAX INTEGER { ubr(0), cbr(1), rtVbr(2), nrtVbr(3) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the ATM service category that is used for this connection." ::= { mcsMgrFrf5EpGEpOperEntry 6 } mcsMgrFrf5EpGEpPeakCellRate01 OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the Peak Cell Rate (PCR) of the FRF.5 ATM VCC for all cells (with CLP=0 and CLP=1). The pcr01 is derived from the End Point traffic parameters using the conversion policy of the connectionTransferPriority. The conversion policy is defined under the ModuleData FrameRelayService AtmNetworking TransferPriority/n component." ::= { mcsMgrFrf5EpGEpOperEntry 8 } mcsMgrFrf5EpGEpSustainedCellRate0 OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the Sustained Cell Rate (SCR) of the FRF.5 ATM VCC for high priority cells (with CLP=0). The scr0 is derived from the End Point traffic parameters using the conversion policy of the connectionTransferPriority. The conversion policy is defined under the ModuleData FrameRelayService AtmNetworking TransferPriority/n component." ::= { mcsMgrFrf5EpGEpOperEntry 9 } mcsMgrFrf5EpGEpSustainedCellRate01 OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the Sustained Cell Rate (SCR) of the FRF.5 ATM VCC for all cells (with CLP=0 and CLP=1). The scr01 is derived from the End Point traffic parameters using the conversion policy of the connectionTransferPriority. The conversion policy is defined under the ModuleData FrameRelayService AtmNetworking TransferPriority/n component." ::= { mcsMgrFrf5EpGEpOperEntry 10 } mcsMgrFrf5EpGEpMaximumBurstSize0 OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the Maximum Burst Size (MBS) of the FRF.5 ATM VCC for high priority cells (with CLP=0). The mbs0 is derived from the End Point traffic parameters using the conversion policy of the connectionTransferPriority. The conversion policy is defined under the ModuleData FrameRelayService AtmNetworking TransferPriority/n component." ::= { mcsMgrFrf5EpGEpOperEntry 11 } mcsMgrFrf5EpGEpMaximumBurstSize01 OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the Maximum Burst Size (MBS) of the FRF.5 ATM VCC for all cells (with CLP=0 and CLP=1). The mbs01 is derived from the End Point traffic parameters using the conversion policy of the connectionTransferPriority. The conversion policy is defined under the ModuleData FrameRelayService AtmNetworking TransferPriority/n component." ::= { mcsMgrFrf5EpGEpOperEntry 12 } mcsMgrFrf5EpGEpAvgFrameSize OBJECT-TYPE SYNTAX Unsigned32 (1..8187) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the average frame size that is used in the traffic parameter conversion policy calculations for this end point." DEFVAL { 128 } ::= { mcsMgrFrf5EpGEpOperEntry 13 } mcsMgrFrf5EpGEpTrafficParmConversionPolicy OBJECT-TYPE SYNTAX INTEGER { n3(3), n4(4), n5(5), n6(6) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the traffic parameter conversion policy used to specify the equivalent ATM bandwidth rate at this end point. Policy 3 characterizes the traffic in the following way: - ATM traffic descriptor type 6 is selected - PCR0+1 is based on the AR - SCR0+1 is based on the CIR and EIR - MBS0+1 is based on Bc,Be,CIR,EIR and AR - Takes into account that the instananeous rate of the frame relay stream can burst above CIR and up tp the AR. Policy 4 characterizes the traffic in the following way: - ATM traffic descriptor type 7 or 8 is selected. Type 7 is chosen when non-conforming cells are to be discarded and type 8 when non-conforming cells are tagged by UPC traffic policer. - PCR0+1 is based on the AR - SCR0 is based on the CIR - MBS0 is based on Bc,CIR and AR - There is no direct characterization of EIR. The allowed EIR can be derived using the difference between the AR and CIR. Policy 5 characterizes the traffic in the following way: - ATM traffic descriptor type 7 or 8 is selected . Type 7 is chosen when non-conforming cells are to be discarded and type 8 when non-conforming cells are tagged by UPC traffic policer - PCR0+1 is based on CIR and EIR - SCR0 is based on the CIR - MBS0 is based on the Bc,CIR and AR - The maximum PCR is no longer based on AR but based on the CIR and EIR. Policy 6 characterizes the traffic in the following way: - ATM traffic descriptor type 3 is selected - PCR0+1 is based only on CIR." ::= { mcsMgrFrf5EpGEpOperEntry 14 } mcsMgrFrf5EpGEpType OBJECT-TYPE SYNTAX INTEGER { master(0), slave(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the FRF.5 End Point type. If the value is master, this End Point is responsible for initiating the call to set up the FRF.5 ATM VCC. If the value is slave, this End Point receives call setup requests from the remote end." ::= { mcsMgrFrf5EpGEpOperEntry 15 } mcsMgrFrf5EpGEpLastVccCauseDiag OBJECT-TYPE SYNTAX HexString (SIZE (1..8)) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the diagnostic value of the last SPVC release message received on the FRF.5 end point Vcc pipe." ::= { mcsMgrFrf5EpGEpOperEntry 20 } -- DsMgr Frf5EpG/n Ep/m LocalManagementInterface -- This component defines the parameters for implementing the Frame -- Relay Forum FRF.5 Local Management Interface protocol. mcsMgrFrf5EpGEpLmi OBJECT IDENTIFIER ::= { mcsMgrFrf5EpGEp 2 } mcsMgrFrf5EpGEpLmiRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF McsMgrFrf5EpGEpLmiRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of mcsMgrFrf5EpGEpLmi components." ::= { mcsMgrFrf5EpGEpLmi 1 } mcsMgrFrf5EpGEpLmiRowStatusEntry OBJECT-TYPE SYNTAX McsMgrFrf5EpGEpLmiRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single mcsMgrFrf5EpGEpLmi component." INDEX { mcsMgrIndex, mcsMgrFrf5EpGIndex, mcsMgrFrf5EpGEpIndex, mcsMgrFrf5EpGEpLmiIndex } ::= { mcsMgrFrf5EpGEpLmiRowStatusTable 1 } McsMgrFrf5EpGEpLmiRowStatusEntry ::= SEQUENCE { mcsMgrFrf5EpGEpLmiRowStatus RowStatus, mcsMgrFrf5EpGEpLmiComponentName DisplayString, mcsMgrFrf5EpGEpLmiStorageType StorageType, mcsMgrFrf5EpGEpLmiIndex NonReplicated } mcsMgrFrf5EpGEpLmiRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-write STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of mcsMgrFrf5EpGEpLmi components. These components can be added and deleted." ::= { mcsMgrFrf5EpGEpLmiRowStatusEntry 1 } mcsMgrFrf5EpGEpLmiComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { mcsMgrFrf5EpGEpLmiRowStatusEntry 2 } mcsMgrFrf5EpGEpLmiStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the mcsMgrFrf5EpGEpLmi tables." ::= { mcsMgrFrf5EpGEpLmiRowStatusEntry 4 } mcsMgrFrf5EpGEpLmiIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the mcsMgrFrf5EpGEpLmi tables." ::= { mcsMgrFrf5EpGEpLmiRowStatusEntry 10 } mcsMgrFrf5EpGEpLmiParmsTable OBJECT-TYPE SYNTAX SEQUENCE OF McsMgrFrf5EpGEpLmiParmsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the provisionable attributes of the Local Management Interface component." ::= { mcsMgrFrf5EpGEpLmi 10 } mcsMgrFrf5EpGEpLmiParmsEntry OBJECT-TYPE SYNTAX McsMgrFrf5EpGEpLmiParmsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the mcsMgrFrf5EpGEpLmiParmsTable." INDEX { mcsMgrIndex, mcsMgrFrf5EpGIndex, mcsMgrFrf5EpGEpIndex, mcsMgrFrf5EpGEpLmiIndex } ::= { mcsMgrFrf5EpGEpLmiParmsTable 1 } McsMgrFrf5EpGEpLmiParmsEntry ::= SEQUENCE { mcsMgrFrf5EpGEpLmiProcedures INTEGER, mcsMgrFrf5EpGEpLmiAsyncStatusReport INTEGER, mcsMgrFrf5EpGEpLmiErrorEventThreshold Unsigned32, mcsMgrFrf5EpGEpLmiEventCount Unsigned32, mcsMgrFrf5EpGEpLmiCheckPointTimer Unsigned32, mcsMgrFrf5EpGEpLmiSide INTEGER } mcsMgrFrf5EpGEpLmiProcedures OBJECT-TYPE SYNTAX INTEGER { none(0), ansi(2), ccitt(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute selects the procedures to be used for the Local Management Interface. The following are the supported procedures: none: no Local Management Interface procedures are running on the ATM VCC. This accomodates remote interworking functions which do not implement LMI procedures. In this case, the remaining attributes of this group will be ignored. ccitt: Local Management Interface procedures from the CCITT specification are supported. Dlci/0 is used for the LMI protocol, to comply with FRF.5. ansi: Local Management Interface procedures from the ANSI specification are supported. DLCI 0 is used for the LMI protocol." DEFVAL { ccitt } ::= { mcsMgrFrf5EpGEpLmiParmsEntry 1 } mcsMgrFrf5EpGEpLmiAsyncStatusReport OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute selects the use of asynchronous PVC status report procedures as specified in the CCITT specification (ITU-T Q.933, Annex A), and the ANSI specification Annex D." DEFVAL { on } ::= { mcsMgrFrf5EpGEpLmiParmsEntry 2 } mcsMgrFrf5EpGEpLmiErrorEventThreshold OBJECT-TYPE SYNTAX Unsigned32 (1..10) ACCESS read-write STATUS mandatory DESCRIPTION "For the network side procedure, an event is defined as follows: (1) receipt of a STATUS ENQUIRY message, or (2) expiration of timer T392. An error event is (1) nonreceipt of STATUS ENQUIRY in T392 seconds; (2) invalid format of an LMI message; (3) invalid receive sequence number. For the user side procedure, an event is defined as a polling cycle or a status enquiry and status report exchange. An error event is (1) non-receipt of a STATUS within the polling cycle, or (2) invalid format of an LMI message, or (3) invalid sequence number. This attribute specifies the number of error events which, if they occur within eventCount events, will cause a protocol error condition. The condition is cleared after eventCount sequential correct events occur. It must be less than or equal to eventCount (n393)." DEFVAL { 3 } ::= { mcsMgrFrf5EpGEpLmiParmsEntry 3 } mcsMgrFrf5EpGEpLmiEventCount OBJECT-TYPE SYNTAX Unsigned32 (1..10) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the number of contiguous events within which no more than eventErrorThreshold error events are allowed. It must be greater than or equal to errorEventThreshold (n392)." DEFVAL { 4 } ::= { mcsMgrFrf5EpGEpLmiParmsEntry 4 } mcsMgrFrf5EpGEpLmiCheckPointTimer OBJECT-TYPE SYNTAX Unsigned32 (5..255) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute selects the time (in seconds) within which a STATUS ENQUIRY message is expected. It must be greater than linkVerificationTimer (t391)." DEFVAL { 200 } ::= { mcsMgrFrf5EpGEpLmiParmsEntry 5 } mcsMgrFrf5EpGEpLmiSide OBJECT-TYPE SYNTAX INTEGER { network(0), user(1), both(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute selects the user side procedure (DTE), or the network side procedure (DCE), or both the user side and the network side procedures of the LMI. This attribute can be set to user, network or both." DEFVAL { both } ::= { mcsMgrFrf5EpGEpLmiParmsEntry 8 } mcsMgrFrf5EpGEpLmiNniParmsTable OBJECT-TYPE SYNTAX SEQUENCE OF McsMgrFrf5EpGEpLmiNniParmsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the provisionable attributes of the FRF.5 LMI procedures which are unique to NNI." ::= { mcsMgrFrf5EpGEpLmi 11 } mcsMgrFrf5EpGEpLmiNniParmsEntry OBJECT-TYPE SYNTAX McsMgrFrf5EpGEpLmiNniParmsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the mcsMgrFrf5EpGEpLmiNniParmsTable." INDEX { mcsMgrIndex, mcsMgrFrf5EpGIndex, mcsMgrFrf5EpGEpIndex, mcsMgrFrf5EpGEpLmiIndex } ::= { mcsMgrFrf5EpGEpLmiNniParmsTable 1 } McsMgrFrf5EpGEpLmiNniParmsEntry ::= SEQUENCE { mcsMgrFrf5EpGEpLmiFullStatusPollingCycles Unsigned32, mcsMgrFrf5EpGEpLmiLinkVerificationTimer Unsigned32 } mcsMgrFrf5EpGEpLmiFullStatusPollingCycles OBJECT-TYPE SYNTAX Unsigned32 (1..255) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies how frequently the FRF.5 LMI initiates a Status Enquiry for a full PVC status report. A polling cycle is a Status Enquiry and Status Report exchange." DEFVAL { 1 } ::= { mcsMgrFrf5EpGEpLmiNniParmsEntry 1 } mcsMgrFrf5EpGEpLmiLinkVerificationTimer OBJECT-TYPE SYNTAX Unsigned32 (5..255) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies how frequently the FRF.5 LMI initiates a Status Enquiry for link integrity verification. It must be less than checkPointTimer (t392)." DEFVAL { 180 } ::= { mcsMgrFrf5EpGEpLmiNniParmsEntry 2 } mcsMgrFrf5EpGEpLmiStateTable OBJECT-TYPE SYNTAX SEQUENCE OF McsMgrFrf5EpGEpLmiStateEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide." ::= { mcsMgrFrf5EpGEpLmi 12 } mcsMgrFrf5EpGEpLmiStateEntry OBJECT-TYPE SYNTAX McsMgrFrf5EpGEpLmiStateEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the mcsMgrFrf5EpGEpLmiStateTable." INDEX { mcsMgrIndex, mcsMgrFrf5EpGIndex, mcsMgrFrf5EpGEpIndex, mcsMgrFrf5EpGEpLmiIndex } ::= { mcsMgrFrf5EpGEpLmiStateTable 1 } McsMgrFrf5EpGEpLmiStateEntry ::= SEQUENCE { mcsMgrFrf5EpGEpLmiAdminState INTEGER, mcsMgrFrf5EpGEpLmiOperationalState INTEGER, mcsMgrFrf5EpGEpLmiUsageState INTEGER } mcsMgrFrf5EpGEpLmiAdminState OBJECT-TYPE SYNTAX INTEGER { locked(0), unlocked(1), shuttingDown(2) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component." DEFVAL { unlocked } ::= { mcsMgrFrf5EpGEpLmiStateEntry 1 } mcsMgrFrf5EpGEpLmiOperationalState OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle." DEFVAL { disabled } ::= { mcsMgrFrf5EpGEpLmiStateEntry 2 } mcsMgrFrf5EpGEpLmiUsageState OBJECT-TYPE SYNTAX INTEGER { idle(0), active(1), busy(2) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time." DEFVAL { idle } ::= { mcsMgrFrf5EpGEpLmiStateEntry 3 } mcsMgrFrf5EpGEpLmiPsiTable OBJECT-TYPE SYNTAX SEQUENCE OF McsMgrFrf5EpGEpLmiPsiEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group provides the protocol status of the Local Management Interface." ::= { mcsMgrFrf5EpGEpLmi 13 } mcsMgrFrf5EpGEpLmiPsiEntry OBJECT-TYPE SYNTAX McsMgrFrf5EpGEpLmiPsiEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the mcsMgrFrf5EpGEpLmiPsiTable." INDEX { mcsMgrIndex, mcsMgrFrf5EpGIndex, mcsMgrFrf5EpGEpIndex, mcsMgrFrf5EpGEpLmiIndex } ::= { mcsMgrFrf5EpGEpLmiPsiTable 1 } McsMgrFrf5EpGEpLmiPsiEntry ::= SEQUENCE { mcsMgrFrf5EpGEpLmiProtocolStatus INTEGER } mcsMgrFrf5EpGEpLmiProtocolStatus OBJECT-TYPE SYNTAX INTEGER { errorCondition(0), normalCondition(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates whether the LMI is in an error condition or whether the protocol is behaving normally. This attribute will be set to errorCondition after enough LMI errors have been detected to warrant a change in condition. This occurs when n392 of the last n393 events are in error. The error condition is lifted when a sufficient number of consecutive events has occurred without error. This occurs when n393 consecutive good events take place. The consequence of an error condition is that all DLCIs on this interface will become inactive in both directions." DEFVAL { normalCondition } ::= { mcsMgrFrf5EpGEpLmiPsiEntry 1 } mcsMgrFrf5EpGEpLmiStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF McsMgrFrf5EpGEpLmiStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the operational statistics for the FRF.5 NNI Local Management Interface." ::= { mcsMgrFrf5EpGEpLmi 14 } mcsMgrFrf5EpGEpLmiStatsEntry OBJECT-TYPE SYNTAX McsMgrFrf5EpGEpLmiStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the mcsMgrFrf5EpGEpLmiStatsTable." INDEX { mcsMgrIndex, mcsMgrFrf5EpGIndex, mcsMgrFrf5EpGEpIndex, mcsMgrFrf5EpGEpLmiIndex } ::= { mcsMgrFrf5EpGEpLmiStatsTable 1 } McsMgrFrf5EpGEpLmiStatsEntry ::= SEQUENCE { mcsMgrFrf5EpGEpLmiKeepAliveStatusToInterface Counter32, mcsMgrFrf5EpGEpLmiFullStatusToInterface Counter32, mcsMgrFrf5EpGEpLmiKeepAliveStatusEnqFromInterface Counter32, mcsMgrFrf5EpGEpLmiFullStatusEnqFromInterface Counter32, mcsMgrFrf5EpGEpLmiNetworkSideEventHistory AsciiString, mcsMgrFrf5EpGEpLmiUserSideEventHistory AsciiString, mcsMgrFrf5EpGEpLmiProtocolErrors Counter32, mcsMgrFrf5EpGEpLmiUnexpectedIes Counter32, mcsMgrFrf5EpGEpLmiSequenceErrors Counter32, mcsMgrFrf5EpGEpLmiStatusSequenceErrors Counter32, mcsMgrFrf5EpGEpLmiUnexpectedReports Counter32, mcsMgrFrf5EpGEpLmiPollingVerifTimeouts Counter32, mcsMgrFrf5EpGEpLmiNoStatusReportCount Counter32, mcsMgrFrf5EpGEpLmiKeepAliveEnqToIf Counter32, mcsMgrFrf5EpGEpLmiFullStatusEnqToIf Counter32 } mcsMgrFrf5EpGEpLmiKeepAliveStatusToInterface OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the Local Management Interface keep alive status messages sent to the ATM VCC in response to a status enquiry for keep alive status. When the maximum count is reached it wraps to zero." ::= { mcsMgrFrf5EpGEpLmiStatsEntry 1 } mcsMgrFrf5EpGEpLmiFullStatusToInterface OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the Local Management Interface full status messages sent to the ATM VCC in response to a status enquiry for keep alive or full status. When the maximum count is reached it wraps to zero." ::= { mcsMgrFrf5EpGEpLmiStatsEntry 2 } mcsMgrFrf5EpGEpLmiKeepAliveStatusEnqFromInterface OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the Local Management Interface valid keep alive status enquiry messages received from the ATM VCC. When the maximum count is reached it wraps to zero." ::= { mcsMgrFrf5EpGEpLmiStatsEntry 3 } mcsMgrFrf5EpGEpLmiFullStatusEnqFromInterface OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the Local Management Interface valid full status enquiry messages received from the ATM VCC. When the maximum count is reached it wraps to zero." ::= { mcsMgrFrf5EpGEpLmiStatsEntry 4 } mcsMgrFrf5EpGEpLmiNetworkSideEventHistory OBJECT-TYPE SYNTAX AsciiString (SIZE (1..10)) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute displays the Local Management Interface network side procedure event history in order of occurrence. An event is represented by a single symbol. A '+' symbol indicates a good event. An 'X' symbol indicates a protocol error event. The left most event is the most recent to occur. The provisioned eventCount dictates the maximum number of events displayed. A good event is triggered by receipt of a valid status enquiry message. An error event is either a T392 timer expiry or receipt of a status enquiry with an incorrect sequence number." ::= { mcsMgrFrf5EpGEpLmiStatsEntry 5 } mcsMgrFrf5EpGEpLmiUserSideEventHistory OBJECT-TYPE SYNTAX AsciiString (SIZE (1..10)) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute displays the Local Management Interface user side procedure event history in order of occurrence. An event is represented by a single symbol. A '+' symbol indicates a good event. An 'X' symbol indicates a protocol error event. The left most event is the most recent to occur. The provisioned eventCount dictates the maximum number of events displayed. A good event is triggered by receipt of a valid status message. An error event is either a T391 timer expiry or receipt of a status message with an incorrect sequence number." ::= { mcsMgrFrf5EpGEpLmiStatsEntry 6 } mcsMgrFrf5EpGEpLmiProtocolErrors OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the number of Local Management Interface protocol errors. It is the sum of the sequence (sequenceErrors and statusSequenceErrors) and timeout (pollingVerifTimeouts and noStatusReportCount) errors. When the maximum count is reached it wraps to zero." ::= { mcsMgrFrf5EpGEpLmiStatsEntry 7 } mcsMgrFrf5EpGEpLmiUnexpectedIes OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the number of Local Managament Interface frames received with an Information Element identifier that is unknown or unexpected. An unexpected Information Element is not a protocol error. When the maximum count is reached, this counter wraps to zero." ::= { mcsMgrFrf5EpGEpLmiStatsEntry 8 } mcsMgrFrf5EpGEpLmiSequenceErrors OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the number of Local Management Interface Status Enquiry message sequence errors. A sequence error is receipt of a Status Enquiry message with a receive sequence number not equal to the last send sequence number. When the maximum count is reached the counter wraps to zero." ::= { mcsMgrFrf5EpGEpLmiStatsEntry 9 } mcsMgrFrf5EpGEpLmiStatusSequenceErrors OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the number of Local Management Interface Status message sequence errors. A sequence error is receipt of a Status message with a receive sequence number not equal to the last send sequence number. When the maximum count is reached the counter wraps to zero." ::= { mcsMgrFrf5EpGEpLmiStatsEntry 10 } mcsMgrFrf5EpGEpLmiUnexpectedReports OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the number of Local Management Interface frames received with an unknown or unexpected report type. An unexpected report type is not a protocol error. When the maximum count is reached the counter wraps to zero." ::= { mcsMgrFrf5EpGEpLmiStatsEntry 11 } mcsMgrFrf5EpGEpLmiPollingVerifTimeouts OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the checkPointTimer (T392) expiries occurring on the Local Management Interface. When the maximum count is reached the counter wraps to zero." ::= { mcsMgrFrf5EpGEpLmiStatsEntry 12 } mcsMgrFrf5EpGEpLmiNoStatusReportCount OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the number of times when no status report or an invalid status report comes from the external network. This attribute is incremented: i) after a status enquiry is sent out and the T391 timer expires without having a status report received. ii) if an invalid status report is received. When the maximum count is reached it wraps to zero." ::= { mcsMgrFrf5EpGEpLmiStatsEntry 13 } mcsMgrFrf5EpGEpLmiKeepAliveEnqToIf OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the number of Local Management Interface keep alive enquiry status messages sent to the external user device for keep alive status. When the maximum count is reached it wraps to zero." ::= { mcsMgrFrf5EpGEpLmiStatsEntry 14 } mcsMgrFrf5EpGEpLmiFullStatusEnqToIf OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the number of Local Management Interface full status messages sent to the external user device in response to a status enquiry for keep alive or full status. When the maximum count is reached it wraps to zero." ::= { mcsMgrFrf5EpGEpLmiStatsEntry 15 } -- McsMgr Frf5EpG/n Ep/n EndPointDescriptor -- This component describes the ATM SPVC which supports the -- FRF.5 connection. mcsMgrFrf5EpGEpEpd OBJECT IDENTIFIER ::= { mcsMgrFrf5EpGEp 3 } mcsMgrFrf5EpGEpEpdRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF McsMgrFrf5EpGEpEpdRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of mcsMgrFrf5EpGEpEpd components." ::= { mcsMgrFrf5EpGEpEpd 1 } mcsMgrFrf5EpGEpEpdRowStatusEntry OBJECT-TYPE SYNTAX McsMgrFrf5EpGEpEpdRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single mcsMgrFrf5EpGEpEpd component." INDEX { mcsMgrIndex, mcsMgrFrf5EpGIndex, mcsMgrFrf5EpGEpIndex, mcsMgrFrf5EpGEpEpdIndex } ::= { mcsMgrFrf5EpGEpEpdRowStatusTable 1 } McsMgrFrf5EpGEpEpdRowStatusEntry ::= SEQUENCE { mcsMgrFrf5EpGEpEpdRowStatus RowStatus, mcsMgrFrf5EpGEpEpdComponentName DisplayString, mcsMgrFrf5EpGEpEpdStorageType StorageType, mcsMgrFrf5EpGEpEpdIndex NonReplicated } mcsMgrFrf5EpGEpEpdRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of mcsMgrFrf5EpGEpEpd components. These components cannot be added nor deleted." ::= { mcsMgrFrf5EpGEpEpdRowStatusEntry 1 } mcsMgrFrf5EpGEpEpdComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { mcsMgrFrf5EpGEpEpdRowStatusEntry 2 } mcsMgrFrf5EpGEpEpdStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the mcsMgrFrf5EpGEpEpd tables." ::= { mcsMgrFrf5EpGEpEpdRowStatusEntry 4 } mcsMgrFrf5EpGEpEpdIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the mcsMgrFrf5EpGEpEpd tables." ::= { mcsMgrFrf5EpGEpEpdRowStatusEntry 10 } mcsMgrFrf5EpGEpEpdProvTable OBJECT-TYPE SYNTAX SEQUENCE OF McsMgrFrf5EpGEpEpdProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the provisionable attributes of the FRF.5 End Point." ::= { mcsMgrFrf5EpGEpEpd 10 } mcsMgrFrf5EpGEpEpdProvEntry OBJECT-TYPE SYNTAX McsMgrFrf5EpGEpEpdProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the mcsMgrFrf5EpGEpEpdProvTable." INDEX { mcsMgrIndex, mcsMgrFrf5EpGIndex, mcsMgrFrf5EpGEpIndex, mcsMgrFrf5EpGEpEpdIndex } ::= { mcsMgrFrf5EpGEpEpdProvTable 1 } McsMgrFrf5EpGEpEpdProvEntry ::= SEQUENCE { mcsMgrFrf5EpGEpEpdRemoteConnectionIdentifier IntegerSequence, mcsMgrFrf5EpGEpEpdConnectionTransferPriority Unsigned32, mcsMgrFrf5EpGEpEpdCommittedInformationRate Unsigned32, mcsMgrFrf5EpGEpEpdExcessInformationRate Unsigned32, mcsMgrFrf5EpGEpEpdCommittedBurstSize Unsigned32, mcsMgrFrf5EpGEpEpdType INTEGER, mcsMgrFrf5EpGEpEpdAccessRate Unsigned32, mcsMgrFrf5EpGEpEpdExcessBurstSize Unsigned32 } mcsMgrFrf5EpGEpEpdRemoteConnectionIdentifier OBJECT-TYPE SYNTAX IntegerSequence (SIZE (3..9)) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the remote connection identifier. It either represents the VPI.VCI logical channel number assignment of a remote ATM interface, or the Endpoint.Frf5EndPointGroup instances of a remote Passport FRF.5 EndPoint." ::= { mcsMgrFrf5EpGEpEpdProvEntry 3 } mcsMgrFrf5EpGEpEpdConnectionTransferPriority OBJECT-TYPE SYNTAX Unsigned32 (0..15) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the transfer priority used to establish the ATM connection. The EndPoint references the ModuleData FrameRelayService AtmNetworking TransferPriority/n component to determine the ATM service category to be used by the connection. This attribute is also used to determine which EndPoint within an Frf5EndPointGroup is to multiplex a particular FrAtm Dlci. DESCRIPTION" ::= { mcsMgrFrf5EpGEpEpdProvEntry 4 } mcsMgrFrf5EpGEpEpdCommittedInformationRate OBJECT-TYPE SYNTAX Unsigned32 (0..50000000) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the committed information rate (CIR), and represents the rate at which the network FRF.5 ATM VCC agrees to transfer information under normal conditions. A conservative CIR value would be the sum of the CIRs of all the individual FrAtm Dlcis multiplexed by the VCC. The cir is converted into ATM service parameters according to the conversion policy specified by the connectionTransferPriority attribute. The conversion policy is defined under the ModuleData FrameRelayService AtmNetworking TransferPriority/n component." DEFVAL { 64000 } ::= { mcsMgrFrf5EpGEpEpdProvEntry 5 } mcsMgrFrf5EpGEpEpdExcessInformationRate OBJECT-TYPE SYNTAX Unsigned32 (0..50000000) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the excess information rate (EIR), and represents the rate at which the network FRF.5 ATM VCC attempts to transfer information. A conservative EIR value would be the sum of the EIRs of all the individual FrAtm Dlcis multiplexed by the VCC. The eir is converted into ATM service parameters according to the conversion policy specified by the connectionTransferPriority attribute. The conversion policy is defined under the ModuleData FrameRelayService AtmNetworking TransferPriority/n component." DEFVAL { 0 } ::= { mcsMgrFrf5EpGEpEpdProvEntry 6 } mcsMgrFrf5EpGEpEpdCommittedBurstSize OBJECT-TYPE SYNTAX Unsigned32 (0..50000000) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the committed burst size (Bc), and represents the amount of data that the network FRF.5 ATM VCC agrees to transfer under normal conditions. A conservative Bc value would be the sum of the Bcs of all the individual FrAtm Dlcis multiplexed by the VCC. The bc is converted into ATM service parameters according to the conversion policy specified by the connectionTransferPriority attribute. The conversion policy is defined under the ModuleData FrameRelayService AtmNetworking TransferPriority/n component." DEFVAL { 16000 } ::= { mcsMgrFrf5EpGEpEpdProvEntry 7 } mcsMgrFrf5EpGEpEpdType OBJECT-TYPE SYNTAX INTEGER { master(0), slave(1) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the FRF.5 End Point type. If the value is provisioned as master, this End Point is responsible for initiating the SPVC call to set up the FRF.5 ATM VCC. If the value is provisioned as slave, this End Point receives call setup requests from a master remote end." DEFVAL { master } ::= { mcsMgrFrf5EpGEpEpdProvEntry 8 } mcsMgrFrf5EpGEpEpdAccessRate OBJECT-TYPE SYNTAX Unsigned32 (0..50000000) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute represents the access rate of the FRF.5 EndPoint. A conservative value would be the sum of the access rates of all the FrAtms' that have DLCIs multiplexed by the VCC. The access rate is converted into ATM service parameters when conversion policies 3, 4 and 5 are used. For policy 6, this attribute is ignored." DEFVAL { 1536000 } ::= { mcsMgrFrf5EpGEpEpdProvEntry 9 } mcsMgrFrf5EpGEpEpdExcessBurstSize OBJECT-TYPE SYNTAX Unsigned32 (0..50000000) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the excess burst size (Be), and represents the amount of uncommitted data that the network FRF.5 ATM VCC agrees to transfer under normal conditions. A conservative Be value would be the sum of the Bes of all the individual FrAtm Dlcis multiplexed by the VCC. The be is converted into ATM service parameters according to the conversion policy specified by the connectionTransferPriority attribute. The conversion policy is defined under the ModuleData FrameRelayService AtmNetworking TransferPriority/n component." DEFVAL { 0 } ::= { mcsMgrFrf5EpGEpEpdProvEntry 10 } mcsMgrFrf5EpGEpEpdCidDataTable OBJECT-TYPE SYNTAX SEQUENCE OF McsMgrFrf5EpGEpEpdCidDataEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the attribute for a component's Customer Identifier (CID). Refer to the attribute description for a detailed explanation of CIDs." ::= { mcsMgrFrf5EpGEpEpd 11 } mcsMgrFrf5EpGEpEpdCidDataEntry OBJECT-TYPE SYNTAX McsMgrFrf5EpGEpEpdCidDataEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the mcsMgrFrf5EpGEpEpdCidDataTable." INDEX { mcsMgrIndex, mcsMgrFrf5EpGIndex, mcsMgrFrf5EpGEpIndex, mcsMgrFrf5EpGEpEpdIndex } ::= { mcsMgrFrf5EpGEpEpdCidDataTable 1 } McsMgrFrf5EpGEpEpdCidDataEntry ::= SEQUENCE { mcsMgrFrf5EpGEpEpdCustomerIdentifier Unsigned32 } mcsMgrFrf5EpGEpEpdCustomerIdentifier OBJECT-TYPE SYNTAX Unsigned32 (0 | 1..8191) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute holds the Customer Identifier (CID). Every component has a CID. If a component has a cid attribute, the component's CID is the provisioned value of that attribute; otherwise the component inherits the CID of its parent. The top- level component has a CID of 0. Every operator session also has a CID, which is the CID provisioned for the operator's user ID. An operator will see only the stream data for components having a matching CID. Also, the operator will be allowed to issue commands for only those components which have a matching CID. An operator CID of 0 is used to identify the Network Manager (referred to as 'NetMan' in DPN). This CID matches the CID of any component. Values 1 to 8191 inclusive (equivalent to 'basic CIDs' in DPN) may be assigned to specific customers." DEFVAL { 0 } ::= { mcsMgrFrf5EpGEpEpdCidDataEntry 1 } -- -- *** THIS SUBTREE CURRENTLY NOT IMPLEMENTED *** -- -- McsMgr Frf5EpGrp/n Ep/n DataLinkConnectionIdentifier/n -- This component represents a logical connection multiplexed inside -- the FRF.5 ATM VCC. mcsMgrFrf5EpGEpDlci OBJECT IDENTIFIER ::= { mcsMgrFrf5EpGEp 4 } mcsMgrFrf5EpGEpDlciRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF McsMgrFrf5EpGEpDlciRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This entry controls the addition and deletion of mcsMgrFrf5EpGEpDlci components." ::= { mcsMgrFrf5EpGEpDlci 1 } mcsMgrFrf5EpGEpDlciRowStatusEntry OBJECT-TYPE SYNTAX McsMgrFrf5EpGEpDlciRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single mcsMgrFrf5EpGEpDlci component." INDEX { mcsMgrIndex, mcsMgrFrf5EpGIndex, mcsMgrFrf5EpGEpIndex, mcsMgrFrf5EpGEpDlciIndex } ::= { mcsMgrFrf5EpGEpDlciRowStatusTable 1 } McsMgrFrf5EpGEpDlciRowStatusEntry ::= SEQUENCE { mcsMgrFrf5EpGEpDlciRowStatus RowStatus, mcsMgrFrf5EpGEpDlciComponentName DisplayString, mcsMgrFrf5EpGEpDlciStorageType StorageType, mcsMgrFrf5EpGEpDlciIndex Integer32 } mcsMgrFrf5EpGEpDlciRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of mcsMgrFrf5EpGEpDlci components. These components cannot be added nor deleted." ::= { mcsMgrFrf5EpGEpDlciRowStatusEntry 1 } mcsMgrFrf5EpGEpDlciComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { mcsMgrFrf5EpGEpDlciRowStatusEntry 2 } mcsMgrFrf5EpGEpDlciStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the mcsMgrFrf5EpGEpDlci tables." ::= { mcsMgrFrf5EpGEpDlciRowStatusEntry 4 } mcsMgrFrf5EpGEpDlciIndex OBJECT-TYPE SYNTAX Integer32 (16..1007 | 1022) ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the mcsMgrFrf5EpGEpDlci tables." ::= { mcsMgrFrf5EpGEpDlciRowStatusEntry 10 } mcsMgrFrf5EpGEpDlciOperTable OBJECT-TYPE SYNTAX SEQUENCE OF McsMgrFrf5EpGEpDlciOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains the operational attributes for the FRF.5 DLCI." ::= { mcsMgrFrf5EpGEpDlci 10 } mcsMgrFrf5EpGEpDlciOperEntry OBJECT-TYPE SYNTAX McsMgrFrf5EpGEpDlciOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the mcsMgrFrf5EpGEpDlciOperTable." INDEX { mcsMgrIndex, mcsMgrFrf5EpGIndex, mcsMgrFrf5EpGEpIndex, mcsMgrFrf5EpGEpDlciIndex } ::= { mcsMgrFrf5EpGEpDlciOperTable 1 } McsMgrFrf5EpGEpDlciOperEntry ::= SEQUENCE { mcsMgrFrf5EpGEpDlciABitStatusToIf INTEGER, mcsMgrFrf5EpGEpDlciABitReasonToIf INTEGER, mcsMgrFrf5EpGEpDlciABitStatusFromIf INTEGER, mcsMgrFrf5EpGEpDlciABitReasonFromIf INTEGER, mcsMgrFrf5EpGEpDlciAccessConnectionComponent AsciiString } mcsMgrFrf5EpGEpDlciABitStatusToIf OBJECT-TYPE SYNTAX INTEGER { inactive(0), active(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the most recent A-bit status sent to the ATM VCC. If the value is inactive, the reason for the LMI failure is given by the aBitReasonToNetwork." DEFVAL { inactive } ::= { mcsMgrFrf5EpGEpDlciOperEntry 1 } mcsMgrFrf5EpGEpDlciABitReasonToIf OBJECT-TYPE SYNTAX INTEGER { notApplicable(0), remoteUserSignaled(1), localLmiError(2), remoteLmiError(3), localLinkDown(4), remoteLinkDown(5), pvcDown(6) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the reason for the latest inactive A-bit status sent to the ATM VCC. The value is notApplicable when the aBitStatusToNetwork is active. The value is remoteUserSignaled if the FrAtm originating the A-Bit status has detected that the virtual circuit is down at the remote network through the LMI protocol. The FrAtm must be running network site LMI protocol for this A-Bit status reason to be sent. The value is localLmiError if the LMI protocol is down at this Ep. The value is remoteLmiError if the LMI protocol is down at the FrAtm originating this A-Bit status reason. The value is localLinkDown if the physical interface is disabled at this Ep. The value is pvcDown if no A-Bit status has been sent to this Ep (i.e., no A-Bit status has been relayed from the FrAtm). The value is remoteLinkDown if the physical interface is disabled at the FrAtm originating this A-Bit status reason." DEFVAL { notApplicable } ::= { mcsMgrFrf5EpGEpDlciOperEntry 2 } mcsMgrFrf5EpGEpDlciABitStatusFromIf OBJECT-TYPE SYNTAX INTEGER { inactive(0), active(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the most recent A-bit status received from the ATM VCC. If the value is inactive, the reason for the LMI failure is given by the aBitReasonFromNetwork." DEFVAL { inactive } ::= { mcsMgrFrf5EpGEpDlciOperEntry 3 } mcsMgrFrf5EpGEpDlciABitReasonFromIf OBJECT-TYPE SYNTAX INTEGER { notApplicable(0), remoteUserSignalled(1), localLmiError(2), localLinkDown(4), missingFromLmiReport(7) } ACCESS read-only STATUS mandatory DESCRIPTION "This attributes indicates the reason for the latest inactive A-bit status received from the ATM VCC. The value is notApplicable when the aBitStatusFromNetwork is active. The value is remoteUserSignaled if the remote FRF.5 End Point originating the A-Bit status has detected that the virtual circuit is down at the remote network through the LMI protocol. The remote FRF.5 End Point must be running network site LMI protocol for this A-Bit status reason to be sent. The value is localLmiError if the LMI protocol is down at this Ep. The value is localLinkDown if the physical interface is disabled at this Ep. The value is missingFromLmiReport if the remote FRF.5 End Point did not provide a reason along with the inactive A-Bit status." DEFVAL { notApplicable } ::= { mcsMgrFrf5EpGEpDlciOperEntry 4 } mcsMgrFrf5EpGEpDlciAccessConnectionComponent OBJECT-TYPE SYNTAX AsciiString (SIZE (0..23)) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute identifies the FrAtm Dlci to which this Dlci component is bound." ::= { mcsMgrFrf5EpGEpDlciOperEntry 5 } -- An AtmConnection component is created for each ATM connection -- established by an application. It shows where the data traffic for this -- connection is directed. mcsMgrFrf5EpGEpAtmCon OBJECT IDENTIFIER ::= { mcsMgrFrf5EpGEp 5 } mcsMgrFrf5EpGEpAtmConRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF McsMgrFrf5EpGEpAtmConRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of mcsMgrFrf5EpGEpAtmCon components." ::= { mcsMgrFrf5EpGEpAtmCon 1 } mcsMgrFrf5EpGEpAtmConRowStatusEntry OBJECT-TYPE SYNTAX McsMgrFrf5EpGEpAtmConRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single mcsMgrFrf5EpGEpAtmCon component." INDEX { mcsMgrIndex, mcsMgrFrf5EpGIndex, mcsMgrFrf5EpGEpIndex, mcsMgrFrf5EpGEpAtmConIndex } ::= { mcsMgrFrf5EpGEpAtmConRowStatusTable 1 } McsMgrFrf5EpGEpAtmConRowStatusEntry ::= SEQUENCE { mcsMgrFrf5EpGEpAtmConRowStatus RowStatus, mcsMgrFrf5EpGEpAtmConComponentName DisplayString, mcsMgrFrf5EpGEpAtmConStorageType StorageType, mcsMgrFrf5EpGEpAtmConIndex NonReplicated } mcsMgrFrf5EpGEpAtmConRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of mcsMgrFrf5EpGEpAtmCon components. These components cannot be added nor deleted." ::= { mcsMgrFrf5EpGEpAtmConRowStatusEntry 1 } mcsMgrFrf5EpGEpAtmConComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { mcsMgrFrf5EpGEpAtmConRowStatusEntry 2 } mcsMgrFrf5EpGEpAtmConStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the mcsMgrFrf5EpGEpAtmCon tables." ::= { mcsMgrFrf5EpGEpAtmConRowStatusEntry 4 } mcsMgrFrf5EpGEpAtmConIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the mcsMgrFrf5EpGEpAtmCon tables." ::= { mcsMgrFrf5EpGEpAtmConRowStatusEntry 10 } mcsMgrFrf5EpGEpAtmConOperTable OBJECT-TYPE SYNTAX SEQUENCE OF McsMgrFrf5EpGEpAtmConOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute group contains the operational attributes for the NapAtmConnection component." ::= { mcsMgrFrf5EpGEpAtmCon 10 } mcsMgrFrf5EpGEpAtmConOperEntry OBJECT-TYPE SYNTAX McsMgrFrf5EpGEpAtmConOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the mcsMgrFrf5EpGEpAtmConOperTable." INDEX { mcsMgrIndex, mcsMgrFrf5EpGIndex, mcsMgrFrf5EpGEpIndex, mcsMgrFrf5EpGEpAtmConIndex } ::= { mcsMgrFrf5EpGEpAtmConOperTable 1 } McsMgrFrf5EpGEpAtmConOperEntry ::= SEQUENCE { mcsMgrFrf5EpGEpAtmConNextHop RowPointer } mcsMgrFrf5EpGEpAtmConNextHop OBJECT-TYPE SYNTAX RowPointer ACCESS read-only STATUS mandatory DESCRIPTION "This attribute shows the component name of the AtmIf Vcc Ep or AtmCon component to which this switched connection is established." ::= { mcsMgrFrf5EpGEpAtmConOperEntry 1 } -- -- Version and Compliance statements -- -- Object-Group Statement: -- A list of all current accessible leaf objects. -- OBJECTS { mcsMgrFrf5EpGEpLmiProtocolStatus, -- mcsMgrFrf5EpGEpSustainedCellRate01, -- mcsMgrFrf5EpGEpLmiSequenceErrors, -- mcsMgrFrf5EpGEpLmiAdminState, -- mcsMgrFrf5EpGEpLmiProtocolErrors, -- mcsMgrFrf5EpGEpLastVccCauseDiag, -- mcsMgrFrf5EpGEpLmiFullStatusEnqToIf, -- mcsMgrFrf5EpGEpLmiRowStatus, -- mcsMgrFrf5EpGEpLmiKeepAliveEnqToIf, -- mcsMgrFrf5EpGEpLmiEventCount, -- mcsMgrFrf5EpGEpDlciABitStatusToIf, -- mcsMgrFrf5EpGEpEpdAccessRate, -- mcsMgrFrf5EpGEpEpdComponentName, -- mcsMgrFrf5EpGEpEpdType, -- mcsMgrFrf5EpGEpStandbyStatus, -- mcsMgrFrf5EpGEpTrafficParmConversionPolicy, -- mcsMgrFrf5EpGEpLmiUserSideEventHistory, -- mcsMgrFrf5EpGEpAvailabilityStatus, -- mcsMgrFrf5EpGEpPeakCellRate01, -- mcsMgrFrf5EpGEpDlciStorageType, -- mcsMgrFrf5EpGEpLmiUsageState, -- mcsMgrFrf5EpGEpLmiFullStatusEnqFromInterface, -- mcsMgrFrf5EpGEpLmiSide, -- mcsMgrFrf5EpGEpDlciAccessConnectionComponent, -- mcsMgrFrf5EpGEpAlarmStatus, -- mcsMgrFrf5EpGEpLmiComponentName, -- mcsMgrFrf5EpGEpLmiErrorEventThreshold, -- mcsMgrFrf5EpGEpLmiNetworkSideEventHistory, -- mcsMgrFrf5EpGEpEpdCommittedBurstSize, -- mcsMgrFrf5EpGEpUnknownStatus, -- mcsMgrFrf5EpGEpMaximumBurstSize0, -- mcsMgrFrf5EpGEpLmiProcedures, -- mcsMgrFrf5EpGEpEpdExcessInformationRate, -- mcsMgrFrf5EpGEpEpdExcessBurstSize, -- mcsMgrFrf5EpGEpConnectionTransferPriority, -- mcsMgrFrf5EpGEpLmiOperationalState, -- mcsMgrFrf5EpGEpLmiUnexpectedReports, -- mcsMgrFrf5EpGEpControlStatus, -- mcsMgrFrf5EpGEpEpdRowStatus, -- mcsMgrFrf5EpGEpDlciABitReasonToIf, -- mcsMgrFrf5EpGAddrAddrPreRowStatus, -- mcsMgrFrf5EpGEpEpdCustomerIdentifier, -- mcsMgrFrf5EpGAddrComponentName, -- mcsMgrFrf5EpGEpEpdRemoteConnectionIdentifier, -- mcsMgrFrf5EpGAddrStorageType, -- mcsMgrFrf5EpGStorageType, -- mcsMgrFrf5EpGEpSustainedCellRate0, -- mcsMgrFrf5EpGEpEpdCommittedInformationRate, -- mcsMgrFrf5EpGEpLmiAsyncStatusReport, -- mcsMgrFrf5EpGAddrAddrPreValue, -- mcsMgrFrf5EpGEpAdminState, -- mcsMgrFrf5EpGEpAtmConStorageType, -- mcsMgrFrf5EpGEpOperationalState, -- mcsMgrFrf5EpGEpDlciABitStatusFromIf, -- mcsMgrFrf5EpGEpStorageType, -- mcsMgrFrf5EpGEpLmiFullStatusToInterface, -- mcsMgrFrf5EpGEpEpdConnectionTransferPriority, -- mcsMgrFrf5EpGEpRowStatus, -- mcsMgrFrf5EpGEpEpdStorageType, -- mcsMgrFrf5EpGEpAtmConNextHop, -- mcsMgrFrf5EpGEpLmiLinkVerificationTimer, -- mcsMgrFrf5EpGRowStatus, -- mcsMgrFrf5EpGEpProceduralStatus, -- mcsMgrFrf5EpGEpLmiPollingVerifTimeouts, -- mcsMgrFrf5EpGEpAvgFrameSize, -- mcsMgrFrf5EpGEpDlciABitReasonFromIf, -- mcsMgrFrf5EpGAddrCommentText, -- mcsMgrFrf5EpGEpType, -- mcsMgrFrf5EpGAddrRowStatus, -- mcsMgrFrf5EpGAddrRemoteAddress, -- mcsMgrFrf5EpGEpLmiKeepAliveStatusEnqFromInterface, -- mcsMgrFrf5EpGEpUsageState, -- mcsMgrFrf5EpGEpDlciComponentName, -- mcsMgrFrf5EpGEpMaximumBurstSize01, -- mcsMgrFrf5EpGEpServiceCategory, -- mcsMgrFrf5EpGEpComponentName, -- mcsMgrFrf5EpGEpLmiStorageType, -- mcsMgrFrf5EpGEpAtmConRowStatus, -- mcsMgrFrf5EpGEpLastVccClearCause, -- mcsMgrFrf5EpGEpLmiNoStatusReportCount, -- mcsMgrFrf5EpGEpLmiUnexpectedIes, -- mcsMgrFrf5EpGEpLmiStatusSequenceErrors, -- mcsMgrFrf5EpGEpDlciRowStatus, -- mcsMgrFrf5EpGEpLmiKeepAliveStatusToInterface, -- mcsMgrFrf5EpGEpAtmConComponentName, -- mcsMgrFrf5EpGEpLmiFullStatusPollingCycles, -- mcsMgrFrf5EpGComponentName, -- mcsMgrFrf5EpGEpLmiCheckPointTimer } -- STATUS mandatory -- DESCRIPTION -- "A list of all current accessible leaf objects." frf5EpGroup OBJECT IDENTIFIER ::= { frf5EpMIB 1 } frf5EpGroupBD OBJECT IDENTIFIER ::= { frf5EpGroup 4 } frf5EpGroupBD02 OBJECT IDENTIFIER ::= { frf5EpGroupBD 3 } frf5EpGroupBD02A OBJECT IDENTIFIER ::= { frf5EpGroupBD02 2 } -- Agent-Capabilities Statement: -- PRODUCT-RELEASE "Passport Release 7.0 Frf5Ep." -- STATUS mandatory -- DESCRIPTION "Frf5Ep MIB: MIB Version BD02A, -- Software Version BG00S4C." -- SUPPORTS Nortel-Magellan-Passport-Frf5EpMIB -- INCLUDES { frf5EpGroupBD02A } frf5EpCapabilities OBJECT IDENTIFIER ::= { frf5EpMIB 3 } frf5EpCapabilitiesBD OBJECT IDENTIFIER ::= { frf5EpCapabilities 4 } frf5EpCapabilitiesBD02 OBJECT IDENTIFIER ::= { frf5EpCapabilitiesBD 3 } frf5EpCapabilitiesBD02A OBJECT IDENTIFIER ::= { frf5EpCapabilitiesBD02 2 } END