Nortel-Magellan-Passport-AtmUniMIB DEFINITIONS ::= BEGIN IMPORTS OBJECT-TYPE FROM RFC-1212 passportMIBs FROM Nortel-Magellan-Passport-UsefulDefinitionsMIB Counter32, DisplayString, StorageType, RowStatus, Gauge32, Integer32, Unsigned32 FROM Nortel-Magellan-Passport-StandardTextualConventionsMIB AsciiString, Hex, NonReplicated, AsciiStringIndex FROM Nortel-Magellan-Passport-TextualConventionsMIB atmIfVptIndex, atmIfVpt, atmIfIndex, atmIf FROM Nortel-Magellan-Passport-AtmCoreMIB; -- LAST-UPDATED "9808030000Z" -- ORGANIZATION "Nortel" -- CONTACT-INFO " -- Nortel Magellan Network Management -- -- Postal: P.O. Box 5080, Station F -- Ottawa, Ontario -- Canada K2C 3T1 -- -- Email: nm_plm@nt.com" -- DESCRIPTION -- "The module describing the Nortel Magellan Passport -- AtmUni Enterprise MIB." atmUniMIB OBJECT IDENTIFIER ::= { passportMIBs 69 } -- AtmIf/n Uni -- This component represents an ATM UNI interface. If this -- component is provisioned the Iisp component can not be -- provisioned under that AtmIf component. If this component is -- deleted, then all associated Vcc components are deleted. atmIfUni OBJECT IDENTIFIER ::= { atmIf 6 } atmIfUniRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfUniRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of atmIfUni components." ::= { atmIfUni 1 } atmIfUniRowStatusEntry OBJECT-TYPE SYNTAX AtmIfUniRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single atmIfUni component." INDEX { atmIfIndex, atmIfUniIndex } ::= { atmIfUniRowStatusTable 1 } AtmIfUniRowStatusEntry ::= SEQUENCE { atmIfUniRowStatus RowStatus, atmIfUniComponentName DisplayString, atmIfUniStorageType StorageType, atmIfUniIndex NonReplicated } atmIfUniRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-write STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of atmIfUni components. These components can be added and deleted." ::= { atmIfUniRowStatusEntry 1 } atmIfUniComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { atmIfUniRowStatusEntry 2 } atmIfUniStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the atmIfUni tables." ::= { atmIfUniRowStatusEntry 4 } atmIfUniIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the atmIfUni tables." ::= { atmIfUniRowStatusEntry 10 } atmIfUniProvTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfUniProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the provisionable attributes for the Uni component." ::= { atmIfUni 10 } atmIfUniProvEntry OBJECT-TYPE SYNTAX AtmIfUniProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfUniProvTable." INDEX { atmIfIndex, atmIfUniIndex } ::= { atmIfUniProvTable 1 } AtmIfUniProvEntry ::= SEQUENCE { atmIfUniVersion INTEGER, atmIfUniSide INTEGER, atmIfUniSoftPvcRetryPeriod Unsigned32, atmIfUniSoftPvpAndPvcRetryPeriod Unsigned32, atmIfUniSoftPvpAndPvcHoldOffTime Unsigned32 } atmIfUniVersion OBJECT-TYPE SYNTAX INTEGER { atmForum30(0), atmForum31(1) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies which specification the UNI complies with. The options are ATM FORUM 3.0 or ATM FORUM 3.1. If this attribute is changed then all switched Vcc components in this interface are cleared due to the fact that the two versions are incompatible." DEFVAL { atmForum31 } ::= { atmIfUniProvEntry 1 } atmIfUniSide OBJECT-TYPE SYNTAX INTEGER { network(0), user(1) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute indicates which side the interface is, user or network." DEFVAL { network } ::= { atmIfUniProvEntry 2 } atmIfUniSoftPvcRetryPeriod OBJECT-TYPE SYNTAX Unsigned32 (20..999999) ACCESS read-write STATUS obsolete DESCRIPTION "This attribute represents the time in seconds to wait between call set up retries. The resolution is to the nearest 10 seconds. This attribute has been obsoleted and is replaced by the softPvpAndPvcRetryPeriod attribute." DEFVAL { 60 } ::= { atmIfUniProvEntry 3 } atmIfUniSoftPvpAndPvcRetryPeriod OBJECT-TYPE SYNTAX Unsigned32 (20..999999) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute represents the time in seconds to wait between soft PVP or soft PVC call setup retries. The resolution is to the nearest 10 seconds." DEFVAL { 60 } ::= { atmIfUniProvEntry 4 } atmIfUniSoftPvpAndPvcHoldOffTime OBJECT-TYPE SYNTAX Unsigned32 (0 | 50..20000) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies how long to hold off retries following a release or the connection. The resolution is to the nearest 50 ms." DEFVAL { 0 } ::= { atmIfUniProvEntry 5 } atmIfUniOperTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfUniOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute group contains the operational attributes for the Uni component." ::= { atmIfUni 11 } atmIfUniOperEntry OBJECT-TYPE SYNTAX AtmIfUniOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfUniOperTable." INDEX { atmIfIndex, atmIfUniIndex } ::= { atmIfUniOperTable 1 } AtmIfUniOperEntry ::= SEQUENCE { atmIfUniMacAddress AsciiString } atmIfUniMacAddress OBJECT-TYPE SYNTAX AsciiString (SIZE (12)) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the MAC address of the port, which is used for address registration of the user side as the default ESI." ::= { atmIfUniOperEntry 1 } atmIfUniAcctOptTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfUniAcctOptEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the provisionable attributes for accounting." ::= { atmIfUni 12 } atmIfUniAcctOptEntry OBJECT-TYPE SYNTAX AtmIfUniAcctOptEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfUniAcctOptTable." INDEX { atmIfIndex, atmIfUniIndex } ::= { atmIfUniAcctOptTable 1 } AtmIfUniAcctOptEntry ::= SEQUENCE { atmIfUniAccountCollection OCTET STRING, atmIfUniAccountConnectionType INTEGER, atmIfUniAccountClass Unsigned32, atmIfUniServiceExchange Unsigned32 } atmIfUniAccountCollection OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute is used to turn accounting on or off for SVC and SPVC connections. It also specifies the reason(s) for which accounting data is collected: billing, test, study, audit or force. If the set of reasons is not empty then accounting records will be generated by this interface in the following situations: - on a TODA changeover if TODA is enabled; - every 12 hours (per connection) if TODA is disabled; - on every call clear (a call record with final cell counts). If none of the reasons is present, then accounting will be suppressed. The reason for collection is recorded in the accounting record, in the attribute callingCollectReason or calledCollectReason as appropriate. Description of bits: bill(0) test(1) study(2) audit(3) force(4)" ::= { atmIfUniAcctOptEntry 1 } atmIfUniAccountConnectionType OBJECT-TYPE SYNTAX INTEGER { origTerm(0), intermediate(1) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies whether accounting records generated by this interface should be marked as originating, terminating or intermediate. This attribute, in combination with the direction of the call, determines the value of attribute connPointType of the accounting record and may be used by downstream accounting processes to correlate the records. If the value is origTerm then records generated for incoming calls will be marked as originating and records generated for outgoing calls will be marked as terminating. If the value is intermediate then records generated for all calls will be marked as intermediate." DEFVAL { origTerm } ::= { atmIfUniAcctOptEntry 2 } atmIfUniAccountClass OBJECT-TYPE SYNTAX Unsigned32 (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the accounting class associated with the interface. Its meaning is determined by the network operator. Its value is simply recorded in the accounting records generated by this interface, in the attribute callingServiceType or calledServiceType as appropriate." DEFVAL { 0 } ::= { atmIfUniAcctOptEntry 3 } atmIfUniServiceExchange OBJECT-TYPE SYNTAX Unsigned32 (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the data service exchange associated with this interface. Its meaning is determined by the network operator. Its value is simply recorded in the accounting records generated by this interface, in the attribute callingDse or calledDse as appropriate." DEFVAL { 0 } ::= { atmIfUniAcctOptEntry 4 } -- AtmIf/n Uni Ilmi -- This component represents the Interim Local Management Interface -- (ILMI) protocol on the interface. atmIfUniIlmi OBJECT IDENTIFIER ::= { atmIfUni 2 } atmIfUniIlmiRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfUniIlmiRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of atmIfUniIlmi components." ::= { atmIfUniIlmi 1 } atmIfUniIlmiRowStatusEntry OBJECT-TYPE SYNTAX AtmIfUniIlmiRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single atmIfUniIlmi component." INDEX { atmIfIndex, atmIfUniIndex, atmIfUniIlmiIndex } ::= { atmIfUniIlmiRowStatusTable 1 } AtmIfUniIlmiRowStatusEntry ::= SEQUENCE { atmIfUniIlmiRowStatus RowStatus, atmIfUniIlmiComponentName DisplayString, atmIfUniIlmiStorageType StorageType, atmIfUniIlmiIndex NonReplicated } atmIfUniIlmiRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of atmIfUniIlmi components. These components cannot be added nor deleted." ::= { atmIfUniIlmiRowStatusEntry 1 } atmIfUniIlmiComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { atmIfUniIlmiRowStatusEntry 2 } atmIfUniIlmiStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the atmIfUniIlmi tables." ::= { atmIfUniIlmiRowStatusEntry 4 } atmIfUniIlmiIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the atmIfUniIlmi tables." ::= { atmIfUniIlmiRowStatusEntry 10 } atmIfUniIlmiStateTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfUniIlmiStateEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide." ::= { atmIfUniIlmi 10 } atmIfUniIlmiStateEntry OBJECT-TYPE SYNTAX AtmIfUniIlmiStateEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfUniIlmiStateTable." INDEX { atmIfIndex, atmIfUniIndex, atmIfUniIlmiIndex } ::= { atmIfUniIlmiStateTable 1 } AtmIfUniIlmiStateEntry ::= SEQUENCE { atmIfUniIlmiAdminState INTEGER, atmIfUniIlmiOperationalState INTEGER, atmIfUniIlmiUsageState INTEGER } atmIfUniIlmiAdminState OBJECT-TYPE SYNTAX INTEGER { locked(0), unlocked(1), shuttingDown(2) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component." DEFVAL { unlocked } ::= { atmIfUniIlmiStateEntry 1 } atmIfUniIlmiOperationalState OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle." DEFVAL { disabled } ::= { atmIfUniIlmiStateEntry 2 } atmIfUniIlmiUsageState OBJECT-TYPE SYNTAX INTEGER { idle(0), active(1), busy(2) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time." DEFVAL { idle } ::= { atmIfUniIlmiStateEntry 3 } atmIfUniIlmiProvTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfUniIlmiProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute group contains the provisionable attributes for the Ilmi component." ::= { atmIfUniIlmi 11 } atmIfUniIlmiProvEntry OBJECT-TYPE SYNTAX AtmIfUniIlmiProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfUniIlmiProvTable." INDEX { atmIfIndex, atmIfUniIndex, atmIfUniIlmiIndex } ::= { atmIfUniIlmiProvTable 1 } AtmIfUniIlmiProvEntry ::= SEQUENCE { atmIfUniIlmiVci Unsigned32, atmIfUniIlmiOperatingMode INTEGER } atmIfUniIlmiVci OBJECT-TYPE SYNTAX Unsigned32 (0..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute identifies the ILMI channel number." DEFVAL { 16 } ::= { atmIfUniIlmiProvEntry 1 } atmIfUniIlmiOperatingMode OBJECT-TYPE SYNTAX INTEGER { addressRegEnabled(0), addressRegDisabled(1), ilmiDisabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute is used to enable/disable the ILMI protocol. addressRegEnabled indicates that the ILMI address registration protocol is enabled. addressRegDisabled indicates that the ILMI address registration protocol is disabled. ilmiDisabled indicates that all of ILMI is disabled." DEFVAL { addressRegEnabled } ::= { atmIfUniIlmiProvEntry 2 } atmIfUniIlmiStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfUniIlmiStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute group contains the statistics for the AtmIlmi component." ::= { atmIfUniIlmi 12 } atmIfUniIlmiStatsEntry OBJECT-TYPE SYNTAX AtmIfUniIlmiStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfUniIlmiStatsTable." INDEX { atmIfIndex, atmIfUniIndex, atmIfUniIlmiIndex } ::= { atmIfUniIlmiStatsTable 1 } AtmIfUniIlmiStatsEntry ::= SEQUENCE { atmIfUniIlmiTxPdus Counter32, atmIfUniIlmiRxPdus Counter32, atmIfUniIlmiRxBadPdusDiscarded Counter32 } atmIfUniIlmiTxPdus OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the number of transmitted ILMI PDUs. The counter wraps to 0 when the maximum value is exceeded." ::= { atmIfUniIlmiStatsEntry 1 } atmIfUniIlmiRxPdus OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the total number of received ILMI PDUs.The counter wraps to 0 when the maximum value is exceeded." ::= { atmIfUniIlmiStatsEntry 2 } atmIfUniIlmiRxBadPdusDiscarded OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the number of received ILMI PDUs that were discarded due to invalid SNMP format. The counter wraps to 0 when the maximum value is exceeded." ::= { atmIfUniIlmiStatsEntry 3 } atmIfUniIlmiPrefixToRegisterTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfUniIlmiPrefixToRegisterEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute is a list of zero or more addresses. If the side attribute in the Uni component is set to user, then this attribute must be empty; if the side attribute is set to network, then this attribute is a list of prefixes.This attribute represents a list of prefix addresses (26 digits) that are sent to the user side. If no prefixes are entered, then the nodeAddress attribute in the AtmCallRouter component is used for address registration." ::= { atmIfUniIlmi 287 } atmIfUniIlmiPrefixToRegisterEntry OBJECT-TYPE SYNTAX AtmIfUniIlmiPrefixToRegisterEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfUniIlmiPrefixToRegisterTable." INDEX { atmIfIndex, atmIfUniIndex, atmIfUniIlmiIndex, atmIfUniIlmiPrefixToRegisterValue } ::= { atmIfUniIlmiPrefixToRegisterTable 1 } AtmIfUniIlmiPrefixToRegisterEntry ::= SEQUENCE { atmIfUniIlmiPrefixToRegisterValue AsciiString, atmIfUniIlmiPrefixToRegisterRowStatus RowStatus } atmIfUniIlmiPrefixToRegisterValue OBJECT-TYPE SYNTAX AsciiString (SIZE (26)) ACCESS read-write STATUS mandatory DESCRIPTION "This variable represents both the value and the index for the atmIfUniIlmiPrefixToRegisterTable." ::= { atmIfUniIlmiPrefixToRegisterEntry 1 } atmIfUniIlmiPrefixToRegisterRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS write-only STATUS mandatory DESCRIPTION "This variable is used to control the addition and deletion of individual values of the atmIfUniIlmiPrefixToRegisterTable." ::= { atmIfUniIlmiPrefixToRegisterEntry 2 } atmIfUniIlmiEsiToRegisterTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfUniIlmiEsiToRegisterEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute is a list of zero or more addresses. If the side attribute in the Uni component is set to network, then this attribute must be an empty list; if the side attribute is set to user, then this attribute is a list of end system indicators (ESI) addresses (12 hex digits) that are used to compose addresses to register with the network side." ::= { atmIfUniIlmi 288 } atmIfUniIlmiEsiToRegisterEntry OBJECT-TYPE SYNTAX AtmIfUniIlmiEsiToRegisterEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfUniIlmiEsiToRegisterTable." INDEX { atmIfIndex, atmIfUniIndex, atmIfUniIlmiIndex, atmIfUniIlmiEsiToRegisterValue } ::= { atmIfUniIlmiEsiToRegisterTable 1 } AtmIfUniIlmiEsiToRegisterEntry ::= SEQUENCE { atmIfUniIlmiEsiToRegisterValue AsciiString, atmIfUniIlmiEsiToRegisterRowStatus RowStatus } atmIfUniIlmiEsiToRegisterValue OBJECT-TYPE SYNTAX AsciiString (SIZE (12)) ACCESS read-write STATUS mandatory DESCRIPTION "This variable represents both the value and the index for the atmIfUniIlmiEsiToRegisterTable." ::= { atmIfUniIlmiEsiToRegisterEntry 1 } atmIfUniIlmiEsiToRegisterRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS write-only STATUS mandatory DESCRIPTION "This variable is used to control the addition and deletion of individual values of the atmIfUniIlmiEsiToRegisterTable." ::= { atmIfUniIlmiEsiToRegisterEntry 2 } -- AtmIf/n Iisp Signalling -- AtmIf/n Uni Signalling -- AtmIf/n Pnni Signalling -- AtmIf/n Vpt/m Iisp Signalling -- AtmIf/n Vpt/m Uni Signalling -- AtmIf/n Vpt/m Pnni Signalling -- -- This component represents the signalling entities for the interface. atmIfUniSig OBJECT IDENTIFIER ::= { atmIfUni 3 } atmIfUniSigRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfUniSigRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of atmIfUniSig components." ::= { atmIfUniSig 1 } atmIfUniSigRowStatusEntry OBJECT-TYPE SYNTAX AtmIfUniSigRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single atmIfUniSig component." INDEX { atmIfIndex, atmIfUniIndex, atmIfUniSigIndex } ::= { atmIfUniSigRowStatusTable 1 } AtmIfUniSigRowStatusEntry ::= SEQUENCE { atmIfUniSigRowStatus RowStatus, atmIfUniSigComponentName DisplayString, atmIfUniSigStorageType StorageType, atmIfUniSigIndex NonReplicated } atmIfUniSigRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of atmIfUniSig components. These components cannot be added nor deleted." ::= { atmIfUniSigRowStatusEntry 1 } atmIfUniSigComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { atmIfUniSigRowStatusEntry 2 } atmIfUniSigStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the atmIfUniSig tables." ::= { atmIfUniSigRowStatusEntry 4 } atmIfUniSigIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the atmIfUniSig tables." ::= { atmIfUniSigRowStatusEntry 10 } atmIfUniSigProvTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfUniSigProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute group contains the provisionable attributes for the Signalling component." ::= { atmIfUniSig 10 } atmIfUniSigProvEntry OBJECT-TYPE SYNTAX AtmIfUniSigProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfUniSigProvTable." INDEX { atmIfIndex, atmIfUniIndex, atmIfUniSigIndex } ::= { atmIfUniSigProvTable 1 } AtmIfUniSigProvEntry ::= SEQUENCE { atmIfUniSigVci Unsigned32, atmIfUniSigAddressConversion INTEGER } atmIfUniSigVci OBJECT-TYPE SYNTAX Unsigned32 (0..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the signalling channel number." DEFVAL { 5 } ::= { atmIfUniSigProvEntry 1 } atmIfUniSigAddressConversion OBJECT-TYPE SYNTAX INTEGER { none(0), nativeE164(1), nsap(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the address conversion on the outgoing signalling PDUs. The options are none, nativeE164, or nsap. The none option is the default and if this option is chosen then nothing is done to the address information element (IE) in the outgoing signalling message. If nativeE164 option is chosen, then only NSAP encapsulated E.164 addresses with zeros in the ESI are converted to native E.164 format in the outgoing signalling message. If the NSAP address is not encapsulated E.164 or the ESI field is not zeros and the nativeE164 option is chosen, then the call is cleared. If the nsap option is chosen, then native E.164 addresses are converted to NSAP E.164 with zeros in the ESI field; otherwise the address is in NSAP format and is not changed." DEFVAL { none } ::= { atmIfUniSigProvEntry 2 } atmIfUniSigStateTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfUniSigStateEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide." ::= { atmIfUniSig 11 } atmIfUniSigStateEntry OBJECT-TYPE SYNTAX AtmIfUniSigStateEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfUniSigStateTable." INDEX { atmIfIndex, atmIfUniIndex, atmIfUniSigIndex } ::= { atmIfUniSigStateTable 1 } AtmIfUniSigStateEntry ::= SEQUENCE { atmIfUniSigAdminState INTEGER, atmIfUniSigOperationalState INTEGER, atmIfUniSigUsageState INTEGER } atmIfUniSigAdminState OBJECT-TYPE SYNTAX INTEGER { locked(0), unlocked(1), shuttingDown(2) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component." DEFVAL { unlocked } ::= { atmIfUniSigStateEntry 1 } atmIfUniSigOperationalState OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle." DEFVAL { disabled } ::= { atmIfUniSigStateEntry 2 } atmIfUniSigUsageState OBJECT-TYPE SYNTAX INTEGER { idle(0), active(1), busy(2) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time." DEFVAL { idle } ::= { atmIfUniSigStateEntry 3 } atmIfUniSigOperTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfUniSigOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute contains the operational attributes for the AtmSignalling component." ::= { atmIfUniSig 12 } atmIfUniSigOperEntry OBJECT-TYPE SYNTAX AtmIfUniSigOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfUniSigOperTable." INDEX { atmIfIndex, atmIfUniIndex, atmIfUniSigIndex } ::= { atmIfUniSigOperTable 1 } AtmIfUniSigOperEntry ::= SEQUENCE { atmIfUniSigLastTxCauseCode Unsigned32, atmIfUniSigLastTxDiagCode Hex, atmIfUniSigLastRxCauseCode Unsigned32, atmIfUniSigLastRxDiagCode Hex } atmIfUniSigLastTxCauseCode OBJECT-TYPE SYNTAX Unsigned32 (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the cause code in the last transmitted signalling message that contains the CAUSE information element. The cause code is used to describe the reason for generating certain signalling messages." ::= { atmIfUniSigOperEntry 1 } atmIfUniSigLastTxDiagCode OBJECT-TYPE SYNTAX Hex (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute contains the diagnostic code in the last transmitted signalling message. The diagnostic code is contained in the CAUSE information element and identifies an information element type or timer type. The diagnostic code is present only if a procedural error is detected by the signalling protocol. A diagnostic code is always accompanied by the cause code. If there is no failure, this attribute is set to 0." ::= { atmIfUniSigOperEntry 2 } atmIfUniSigLastRxCauseCode OBJECT-TYPE SYNTAX Unsigned32 (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute contains the cause code in the last received signalling message that contains the CAUSE information element. The cause code is used to describe the reason for generating certain signalling messages." ::= { atmIfUniSigOperEntry 3 } atmIfUniSigLastRxDiagCode OBJECT-TYPE SYNTAX Hex (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute contains the diagnostic code in the last received signalling message. The diagnostic code is contained in the CAUSE information element and identifies an information element type or timer type. The diagnostic code is present only if a procedural error is detected by the signalling protocol. A diagnostic code is always accompanied by the cause code. If there is no failure, this attribute is set to 0." ::= { atmIfUniSigOperEntry 4 } atmIfUniSigStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfUniSigStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute group contains the statistics associated with the AtmSignalling component." ::= { atmIfUniSig 13 } atmIfUniSigStatsEntry OBJECT-TYPE SYNTAX AtmIfUniSigStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfUniSigStatsTable." INDEX { atmIfIndex, atmIfUniIndex, atmIfUniSigIndex } ::= { atmIfUniSigStatsTable 1 } AtmIfUniSigStatsEntry ::= SEQUENCE { atmIfUniSigCurrentConnections Counter32, atmIfUniSigPeakConnections Gauge32, atmIfUniSigSuccessfulConnections Counter32, atmIfUniSigFailedConnections Counter32, atmIfUniSigTxPdus Counter32, atmIfUniSigRxPdus Counter32, atmIfUniSigCurrentPmpConnections Gauge32, atmIfUniSigPeakPmpConnections Gauge32, atmIfUniSigSuccessfulPmpConnections Counter32, atmIfUniSigFailedPmpConnections Counter32, atmIfUniSigNewCurrentConnections Gauge32 } atmIfUniSigCurrentConnections OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS obsolete DESCRIPTION "This attribute indicates the total number of currently active connections." ::= { atmIfUniSigStatsEntry 1 } atmIfUniSigPeakConnections OBJECT-TYPE SYNTAX Gauge32 (0..4294967295) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the high water mark of active point-to- point and point-to-multipoint connections." ::= { atmIfUniSigStatsEntry 2 } atmIfUniSigSuccessfulConnections OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the total number of switched point-to- point and point-to-multipoint connections that were successfully established. The counter wraps to 0 when the maximum value is exceeded." ::= { atmIfUniSigStatsEntry 3 } atmIfUniSigFailedConnections OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the total number of switched connections that were not successfully established.The counter wraps to 0 when the maximum value is exceeded." ::= { atmIfUniSigStatsEntry 4 } atmIfUniSigTxPdus OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the number of transmitted signalling PDUs.The counter wraps to 0 when the maximum value is exceeded." ::= { atmIfUniSigStatsEntry 5 } atmIfUniSigRxPdus OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the number of received signalling PDUs.The counter wraps to 0 when the maximum value is exceeded." ::= { atmIfUniSigStatsEntry 6 } atmIfUniSigCurrentPmpConnections OBJECT-TYPE SYNTAX Gauge32 (0..4294967295) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the number of currently active point-to- multipoint connections." ::= { atmIfUniSigStatsEntry 7 } atmIfUniSigPeakPmpConnections OBJECT-TYPE SYNTAX Gauge32 (0..4294967295) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the high water mark of active point-to- multipoint connections." ::= { atmIfUniSigStatsEntry 8 } atmIfUniSigSuccessfulPmpConnections OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the total number of switched point-to- multipoint connections that were successfully established. The counter wraps to 0 when the maximum value is exceeded." ::= { atmIfUniSigStatsEntry 9 } atmIfUniSigFailedPmpConnections OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the number of switched point-to- multipoint connections that were not successfully established.The counter wraps to 0 when the maximum value is exceeded." ::= { atmIfUniSigStatsEntry 10 } atmIfUniSigNewCurrentConnections OBJECT-TYPE SYNTAX Gauge32 (0..4294967295) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the total number of currently active point-to- point and point-to-multipoint connections." ::= { atmIfUniSigStatsEntry 11 } -- AtmIf/n Uni Sig VirtualChannelDescriptor -- AtmIf/n Uni Ilmi VirtualChannelDescriptor -- AtmIf/n Iisp Sig VirtualChannelDescriptor -- AtmIf/n Pnni Sig VirtualChannelDescriptor -- AtmIf/n Pnni Rcc VirtualChannelDescriptor -- AtmIf/n Vpt/m Uni Sig VirtualChannelDescriptor -- AtmIf/n Vpt/m Iisp Sig VirtualChannelDescriptor -- AtmIf/n Vpt/m Pnni Sig VirtualChannelDescriptor -- AtmIf/n Vpt/m Pnni Rcc VirtualChannelDescriptor -- -- This component contains the provisionable traffic parameters for a -- control channel (Sig, Ilmi or Rcc component). atmIfUniSigVcd OBJECT IDENTIFIER ::= { atmIfUniSig 2 } atmIfUniSigVcdRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfUniSigVcdRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of atmIfUniSigVcd components." ::= { atmIfUniSigVcd 1 } atmIfUniSigVcdRowStatusEntry OBJECT-TYPE SYNTAX AtmIfUniSigVcdRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single atmIfUniSigVcd component." INDEX { atmIfIndex, atmIfUniIndex, atmIfUniSigIndex, atmIfUniSigVcdIndex } ::= { atmIfUniSigVcdRowStatusTable 1 } AtmIfUniSigVcdRowStatusEntry ::= SEQUENCE { atmIfUniSigVcdRowStatus RowStatus, atmIfUniSigVcdComponentName DisplayString, atmIfUniSigVcdStorageType StorageType, atmIfUniSigVcdIndex NonReplicated } atmIfUniSigVcdRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-write STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of atmIfUniSigVcd components. These components can be added and deleted." ::= { atmIfUniSigVcdRowStatusEntry 1 } atmIfUniSigVcdComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { atmIfUniSigVcdRowStatusEntry 2 } atmIfUniSigVcdStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the atmIfUniSigVcd tables." ::= { atmIfUniSigVcdRowStatusEntry 4 } atmIfUniSigVcdIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the atmIfUniSigVcd tables." ::= { atmIfUniSigVcdRowStatusEntry 10 } atmIfUniSigVcdProvTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfUniSigVcdProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the provisionable traffic attributes for a control channel." ::= { atmIfUniSigVcd 10 } atmIfUniSigVcdProvEntry OBJECT-TYPE SYNTAX AtmIfUniSigVcdProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfUniSigVcdProvTable." INDEX { atmIfIndex, atmIfUniIndex, atmIfUniSigIndex, atmIfUniSigVcdIndex } ::= { atmIfUniSigVcdProvTable 1 } AtmIfUniSigVcdProvEntry ::= SEQUENCE { atmIfUniSigVcdTrafficDescType INTEGER, atmIfUniSigVcdAtmServiceCategory INTEGER, atmIfUniSigVcdQosClass INTEGER, atmIfUniSigVcdTrafficShaping INTEGER, atmIfUniSigVcdUnshapedTransmitQueueing INTEGER, atmIfUniSigVcdUsageParameterControl INTEGER } atmIfUniSigVcdTrafficDescType OBJECT-TYPE SYNTAX INTEGER { n3(3), n6(6), n7(7), n8(8) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the type of traffic management which is applied to both the transmit and receive direction of this connection as defined in the ATM Forum. The trafficDescType determines the number and meaning of the parameters in the trafficDescParm attribute." DEFVAL { n6 } ::= { atmIfUniSigVcdProvEntry 1 } atmIfUniSigVcdAtmServiceCategory OBJECT-TYPE SYNTAX INTEGER { unspecifiedBitRate(0), constantBitRate(1), rtVariableBitRate(2), nrtVariableBitRate(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the ATM service category for both directions of the connection. The constantBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. The consistent availability of a fixed quantity of bandwidth is considered appropriate for CBR service. Cells which are delayed beyond the value specified by CellTransfer Delay are assumed to be of significantly reduce value to the application. The rtVariableBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. Sources are expected to transmit at a rate which varies with time. Equivalently, the source can be described as 'bursty'. Cells which are delayed beyond the value specified by CTD are assumed to be of significantly reduced value to the application. Real time VBR service may support statistical multiplexing of real time sources. The nrtVariableBitRate service category is intended for non-real time applications which have bursty traffic characteristics and which can be characterized in terms of a PCR, SCR, and MBS. For those cells which are transferred within the traffic contract, the application expects a low cell loss ratio. For all connections, it expects a bound on the mean cell transfer delay. Non-real time VBR service may support statistical multiplexing of connections. The unspecifiedBitRate service is intended for non-real time applications; that is, those not requiring tightly constrained delay and delay variation. UBR sources are expected to be bursty. UBR service supports a high degree of statistical multiplexing among sources. UBR service does not specify traffic related service guarantees. No numerical commitments are made with respect to the cell loss ratio experienced by a UBR connection, or as to the cell transfer delay experienced by cells on the connection." DEFVAL { rtVariableBitRate } ::= { atmIfUniSigVcdProvEntry 3 } atmIfUniSigVcdQosClass OBJECT-TYPE SYNTAX INTEGER { n0(0), n1(1), n2(2), n3(3), n4(4) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the quality of service for both the forward and backward direction for this connection. Class 1 supports a QOS that meets Service Class A performance requirements (Circuit emulation, constant bit rate video). Class 2 supports a QOS that meets Service Class B performance requirements (Variable bit rate audio and video). Class 3 supports a QOS that meets Service Class C performance requirements (Connection-Oriented Data Transfer). Class 4 supports a QOS that meets Service Class D performance requirements (Connectionless Data Transfer). Class 0 is the unspecified bit rate QOS class; no objective is specified for the performance parameters." DEFVAL { n2 } ::= { atmIfUniSigVcdProvEntry 21 } atmIfUniSigVcdTrafficShaping OBJECT-TYPE SYNTAX INTEGER { disabled(1), sameAsCa(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies whether this connection uses traffic shaping when transmitting traffic to the ATM interface. When sameAsCa is selected, traffic shaping for this connection is based on the trafficShaping attribute of the connection's service category component under the AtmIf CA. If the service category has traffic shaping enabled, then traffic shaping is enabled for the connection. Note that enabling traffic shaping may have no effect under certain cases. These cases are listed in the description of the trafficShaping operational attribute, which is under the Vcc Tm and Vpc Tm components. When disabled is selected, traffic shaping for this connection is disabled." DEFVAL { disabled } ::= { atmIfUniSigVcdProvEntry 50 } atmIfUniSigVcdUnshapedTransmitQueueing OBJECT-TYPE SYNTAX INTEGER { common(1), sameAsCa(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute only applies when this connection is unshaped. This attribute specifies the transmit queueing method for this connection if it is unshaped. Refer to the unshapedTransmitQueueing attribute under the AtmIf CA service category subcomponent for more details on the meaning of this attribute. When this attribute is set to sameAsCa, the transmit queueing method for the connection is based on the unshapedTransmitQueueing attribute of the connection's service category component under the ConnectionAdministrator. When this attribute is set to common, transmit traffic on this unshaped connection is destined for the common queue. The value sameAsInterface is for migration from previous software releases, but should no longer be used" DEFVAL { sameAsCa } ::= { atmIfUniSigVcdProvEntry 60 } atmIfUniSigVcdUsageParameterControl OBJECT-TYPE SYNTAX INTEGER { disabled(1), sameAsCa(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies whether this connection enforces usage parameter control when receiving traffic from the ATM interface. When sameAsCa is selected, UPC for the connection is based on the usageParameterControl attribute of the connection's service category component under the ConnectionAdministrator. If the service category has UPC enabled, then UPC is enabled for the connection. Note that enabling UPC may have no effect under certain cases. These cases are listed in the description of the usageParameterControl operational attribute, which is under the Vcc Tm or Vpc Tm component. When disabled is selected, UPC for this connection is disabled. The value sameAsInterface is for migration from previous software releases, but should no longer be used" DEFVAL { disabled } ::= { atmIfUniSigVcdProvEntry 70 } atmIfUniSigVcdTdpTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfUniSigVcdTdpEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute is a vector of five traffic parameters whose meanings are defined by the trafficDescType attribute. The values of peak cell rate (PCR), sustained cell rate (SCR) and requested shaping rate are expressed in cell/s. Maximum burst size (MBS) is expressed in cells. CDVT is expressed in microseconds. The values of PCR, SCR, MBS and CDVT are used for connection admission control (CAC). The value of CDVT is only used for connections where the atmServiceCategory is constantBitRate. For all other values of atmServiceCategory, CDVT is ignored. The values of PCR, SCR and requested shaping rate are used to determine the actual shaping rate where traffic shaping is enabled. When trafficDescType is 3, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameter 1 must be non-zero. Parameters 2 and 3 must be zero. When trafficDescType is 6, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 and 1 traffic; parameter 3 represents the MBS for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. When trafficDescType is 7, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 with cell discard; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. When trafficDescType is 8, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 traffic with cell tagging; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. Whenever it is valid for PCR to be specified, parameter 5 may also be used to specify a requested shaping rate. A non-zero value in parameter 5 overrides the value in parameter 1 and is used as the peak cell rate in calculations of CAC and shaping rate. For trafficDescType 3 the traffic is shaped at the next rate less than the PCR. For trafficDescType 6, 7, and 8, the traffic is shaped at the highest available rate which is between PCR and SCR. However, if there is no available shaping rate between PCR and SCR, traffic is shaped at the next rate above the PCR." ::= { atmIfUniSigVcd 387 } atmIfUniSigVcdTdpEntry OBJECT-TYPE SYNTAX AtmIfUniSigVcdTdpEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfUniSigVcdTdpTable." INDEX { atmIfIndex, atmIfUniIndex, atmIfUniSigIndex, atmIfUniSigVcdIndex, atmIfUniSigVcdTdpIndex } ::= { atmIfUniSigVcdTdpTable 1 } AtmIfUniSigVcdTdpEntry ::= SEQUENCE { atmIfUniSigVcdTdpIndex Integer32, atmIfUniSigVcdTdpValue Unsigned32 } atmIfUniSigVcdTdpIndex OBJECT-TYPE SYNTAX Integer32 (1..5) ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the atmIfUniSigVcdTdpTable specific index for the atmIfUniSigVcdTdpTable." ::= { atmIfUniSigVcdTdpEntry 1 } atmIfUniSigVcdTdpValue OBJECT-TYPE SYNTAX Unsigned32 (0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "This variable represents an individual value for the atmIfUniSigVcdTdpTable." ::= { atmIfUniSigVcdTdpEntry 2 } -- AtmIf/n Iisp Address/address,type -- AtmIf/n Uni Address/address,type -- AtmIf/n Pnni Address/address,type -- AtmIf/n Vpt/m Iisp Address/address,type -- AtmIf/n Vpt/m Uni Address/address,type -- AtmIf/n Vpt/m Pnni Address/address,type -- -- This component represents an address (dynamic or static) -- associated with the interface. The index is a string of 1 to 40 hex -- digits or a single wildcard ('?'), and a type. The type identifies -- whether the Address component is for a primary, alternate, -- registered, or default address. -- -- The types primary and alternate are used for provisioned addresses. -- The type registered is used for dynamic addresses registered -- through ILMI. The type default is used for Soft PVP and Soft PVC -- addresses.Virtual interfaces do not have addresses of -- type default. -- -- The wildcard is only valid for provisioned addresses. If the address -- is a single wildcard, then that indicates that the interface supports -- all addresses. If there is no better match, then this interface may be -- chosen in the routing. If there is more than one interface with a -- single wildcard static address, then the choice is driven through a -- round robin algorithm. -- -- The round robin algorithm tries the primary routes and then the -- alternate routes if none of the primary routes succeed. -- If this node participates in a PNNI hierarchy, then a PnniInfo -- subcomponent can be provisioned under the AtmAddress -- component to specify the level to which this address will be -- advertised. atmIfUniAddr OBJECT IDENTIFIER ::= { atmIfUni 4 } atmIfUniAddrRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfUniAddrRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of atmIfUniAddr components." ::= { atmIfUniAddr 1 } atmIfUniAddrRowStatusEntry OBJECT-TYPE SYNTAX AtmIfUniAddrRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single atmIfUniAddr component." INDEX { atmIfIndex, atmIfUniIndex, atmIfUniAddrAddressIndex, atmIfUniAddrAddressTypeIndex } ::= { atmIfUniAddrRowStatusTable 1 } AtmIfUniAddrRowStatusEntry ::= SEQUENCE { atmIfUniAddrRowStatus RowStatus, atmIfUniAddrComponentName DisplayString, atmIfUniAddrStorageType StorageType, atmIfUniAddrAddressIndex AsciiStringIndex, atmIfUniAddrAddressTypeIndex INTEGER } atmIfUniAddrRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-write STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of atmIfUniAddr components. These components can be added and deleted." ::= { atmIfUniAddrRowStatusEntry 1 } atmIfUniAddrComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { atmIfUniAddrRowStatusEntry 2 } atmIfUniAddrStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the atmIfUniAddr tables." ::= { atmIfUniAddrRowStatusEntry 4 } atmIfUniAddrAddressIndex OBJECT-TYPE SYNTAX AsciiStringIndex (SIZE (1..40)) ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents an index for the atmIfUniAddr tables." ::= { atmIfUniAddrRowStatusEntry 10 } atmIfUniAddrAddressTypeIndex OBJECT-TYPE SYNTAX INTEGER { primary(0), alternate(1), registered(2), default(3) } ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents an index for the atmIfUniAddr tables." ::= { atmIfUniAddrRowStatusEntry 11 } atmIfUniAddrOperTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfUniAddrOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute group contains the operational attributes for the Address component." ::= { atmIfUniAddr 10 } atmIfUniAddrOperEntry OBJECT-TYPE SYNTAX AtmIfUniAddrOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfUniAddrOperTable." INDEX { atmIfIndex, atmIfUniIndex, atmIfUniAddrAddressIndex, atmIfUniAddrAddressTypeIndex } ::= { atmIfUniAddrOperTable 1 } AtmIfUniAddrOperEntry ::= SEQUENCE { atmIfUniAddrScope INTEGER, atmIfUniAddrReachability INTEGER } atmIfUniAddrScope OBJECT-TYPE SYNTAX INTEGER (-1..104) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the scope of the ATM address, which is the highest level to which this address will be advertised in the PNNI hierarchy. If no PnniInfo subcomponent has been provisioned, then the scope will default to the level of this node in the PNNI hierarchy. If this node does not participate in a PNNI hierarchy, then this attribute will have the value of -1." ::= { atmIfUniAddrOperEntry 1 } atmIfUniAddrReachability OBJECT-TYPE SYNTAX INTEGER { internal(0), exterior(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates whether the address is internal or exterior. An internal reachable address is an address of a destination that is directly attached to the logical node advertising the address. An exterior reachable address is an address that can be reached through a PNNI routing domain, but which is not located in that PNNI routing domain." ::= { atmIfUniAddrOperEntry 2 } -- AtmIf/n Iisp Address/address,type TerminateSPvpAndSPvc -- AtmIf/n Uni Address/address,type TerminateSPvpAndSPvc -- AtmIf/n Pnni Address/address,type TerminateSPvpAndSPvc -- AtmIf/n Vpt/m Iisp Address/address,type TerminateSPvpAndSPvc -- AtmIf/n Vpt/m Uni Address/address,type TerminateSPvpAndSPvc -- AtmIf/n Vpt/m Pnni Address/address,type TerminateSPvpAndSPvc -- -- The presence of this subcomponent indicates that SPvp and SPvc -- call setups terminate at this node if the destination address of the -- SPVP or SPVC matches the Address instance. atmIfUniAddrTermSP OBJECT IDENTIFIER ::= { atmIfUniAddr 2 } atmIfUniAddrTermSPRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfUniAddrTermSPRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of atmIfUniAddrTermSP components." ::= { atmIfUniAddrTermSP 1 } atmIfUniAddrTermSPRowStatusEntry OBJECT-TYPE SYNTAX AtmIfUniAddrTermSPRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single atmIfUniAddrTermSP component." INDEX { atmIfIndex, atmIfUniIndex, atmIfUniAddrAddressIndex, atmIfUniAddrAddressTypeIndex, atmIfUniAddrTermSPIndex } ::= { atmIfUniAddrTermSPRowStatusTable 1 } AtmIfUniAddrTermSPRowStatusEntry ::= SEQUENCE { atmIfUniAddrTermSPRowStatus RowStatus, atmIfUniAddrTermSPComponentName DisplayString, atmIfUniAddrTermSPStorageType StorageType, atmIfUniAddrTermSPIndex NonReplicated } atmIfUniAddrTermSPRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-write STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of atmIfUniAddrTermSP components. These components can be added and deleted." ::= { atmIfUniAddrTermSPRowStatusEntry 1 } atmIfUniAddrTermSPComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { atmIfUniAddrTermSPRowStatusEntry 2 } atmIfUniAddrTermSPStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the atmIfUniAddrTermSP tables." ::= { atmIfUniAddrTermSPRowStatusEntry 4 } atmIfUniAddrTermSPIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the atmIfUniAddrTermSP tables." ::= { atmIfUniAddrTermSPRowStatusEntry 10 } -- AtmIf/n Iisp Addr/address,type PnniInfo -- AtmIf/n Uni Addr/address,type PnniInfo -- AtmIf/n Pnni Addr/address,type PnniInfo -- AtmIf/n Vpt/m Iisp Addr/address,type PnniInfo -- AtmIf/n Vpt/m Uni Addr/address,type PnniInfo -- AtmIf/n Vpt/m Pnni Addr/address,type PnniInfo -- -- This component contains provisioned information associated with -- the ATM address related to PNNI. This component appears only -- under provisioned Address components. atmIfUniAddrPnniInfo OBJECT IDENTIFIER ::= { atmIfUniAddr 3 } atmIfUniAddrPnniInfoRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfUniAddrPnniInfoRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of atmIfUniAddrPnniInfo components." ::= { atmIfUniAddrPnniInfo 1 } atmIfUniAddrPnniInfoRowStatusEntry OBJECT-TYPE SYNTAX AtmIfUniAddrPnniInfoRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single atmIfUniAddrPnniInfo component." INDEX { atmIfIndex, atmIfUniIndex, atmIfUniAddrAddressIndex, atmIfUniAddrAddressTypeIndex, atmIfUniAddrPnniInfoIndex } ::= { atmIfUniAddrPnniInfoRowStatusTable 1 } AtmIfUniAddrPnniInfoRowStatusEntry ::= SEQUENCE { atmIfUniAddrPnniInfoRowStatus RowStatus, atmIfUniAddrPnniInfoComponentName DisplayString, atmIfUniAddrPnniInfoStorageType StorageType, atmIfUniAddrPnniInfoIndex NonReplicated } atmIfUniAddrPnniInfoRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-write STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of atmIfUniAddrPnniInfo components. These components can be added and deleted." ::= { atmIfUniAddrPnniInfoRowStatusEntry 1 } atmIfUniAddrPnniInfoComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { atmIfUniAddrPnniInfoRowStatusEntry 2 } atmIfUniAddrPnniInfoStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the atmIfUniAddrPnniInfo tables." ::= { atmIfUniAddrPnniInfoRowStatusEntry 4 } atmIfUniAddrPnniInfoIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the atmIfUniAddrPnniInfo tables." ::= { atmIfUniAddrPnniInfoRowStatusEntry 10 } atmIfUniAddrPnniInfoProvTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfUniAddrPnniInfoProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute group contains the provisioned attributes relating to PNNI for a PnniInfo component." ::= { atmIfUniAddrPnniInfo 10 } atmIfUniAddrPnniInfoProvEntry OBJECT-TYPE SYNTAX AtmIfUniAddrPnniInfoProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfUniAddrPnniInfoProvTable." INDEX { atmIfIndex, atmIfUniIndex, atmIfUniAddrAddressIndex, atmIfUniAddrAddressTypeIndex, atmIfUniAddrPnniInfoIndex } ::= { atmIfUniAddrPnniInfoProvTable 1 } AtmIfUniAddrPnniInfoProvEntry ::= SEQUENCE { atmIfUniAddrPnniInfoScope INTEGER, atmIfUniAddrPnniInfoReachability INTEGER } atmIfUniAddrPnniInfoScope OBJECT-TYPE SYNTAX INTEGER (-1..104) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the scope of the ATM address, which is the highest level up to which this address will be advertised in the PNNI hierarchy. The scope must be set to a value numerically less than or equal to the level of the lowest level peer group containing this node. Setting the scope to 0 will cause the address to be advertised globally within this PNNI routing domain." DEFVAL { -1 } ::= { atmIfUniAddrPnniInfoProvEntry 1 } atmIfUniAddrPnniInfoReachability OBJECT-TYPE SYNTAX INTEGER { internal(0), exterior(1) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute indicates whether the address is internal or exterior. An internal reachable address is an address of a destination that is directly attached to the logical node advertising the address. An exterior reachable address is an address that can be reached through a PNNI routing domain, but which is not located in that PNNI routing domain." DEFVAL { internal } ::= { atmIfUniAddrPnniInfoProvEntry 2 } -- AtmIf/n VirtualPathTerminator/m Uni -- This component represents a virtual ATM UNI interface. If this -- component is provisioned, neither an Iisp component, nor a Pnni -- component can be provisioned under the same Vpt component. If -- this component is deleted, then all associated Vcc components are -- deleted. atmIfVptUni OBJECT IDENTIFIER ::= { atmIfVpt 8 } atmIfVptUniRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptUniRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of atmIfVptUni components." ::= { atmIfVptUni 1 } atmIfVptUniRowStatusEntry OBJECT-TYPE SYNTAX AtmIfVptUniRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single atmIfVptUni component." INDEX { atmIfIndex, atmIfVptIndex, atmIfVptUniIndex } ::= { atmIfVptUniRowStatusTable 1 } AtmIfVptUniRowStatusEntry ::= SEQUENCE { atmIfVptUniRowStatus RowStatus, atmIfVptUniComponentName DisplayString, atmIfVptUniStorageType StorageType, atmIfVptUniIndex NonReplicated } atmIfVptUniRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-write STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of atmIfVptUni components. These components can be added and deleted." ::= { atmIfVptUniRowStatusEntry 1 } atmIfVptUniComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { atmIfVptUniRowStatusEntry 2 } atmIfVptUniStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the atmIfVptUni tables." ::= { atmIfVptUniRowStatusEntry 4 } atmIfVptUniIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the atmIfVptUni tables." ::= { atmIfVptUniRowStatusEntry 10 } atmIfVptUniProvTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptUniProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the provisionable attributes for the Uni component." ::= { atmIfVptUni 10 } atmIfVptUniProvEntry OBJECT-TYPE SYNTAX AtmIfVptUniProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfVptUniProvTable." INDEX { atmIfIndex, atmIfVptIndex, atmIfVptUniIndex } ::= { atmIfVptUniProvTable 1 } AtmIfVptUniProvEntry ::= SEQUENCE { atmIfVptUniVersion INTEGER, atmIfVptUniSide INTEGER, atmIfVptUniSoftPvcRetryPeriod Unsigned32, atmIfVptUniSoftPvpAndPvcRetryPeriod Unsigned32, atmIfVptUniSoftPvpAndPvcHoldOffTime Unsigned32 } atmIfVptUniVersion OBJECT-TYPE SYNTAX INTEGER { atmForum30(0), atmForum31(1) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies which specification the UNI complies with. The options are ATM FORUM 3.0 or ATM FORUM 3.1. If this attribute is changed then all switched Vcc components in this interface are cleared due to the fact that the two versions are incompatible." DEFVAL { atmForum31 } ::= { atmIfVptUniProvEntry 1 } atmIfVptUniSide OBJECT-TYPE SYNTAX INTEGER { network(0), user(1) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute indicates which side the interface is, user or network." DEFVAL { network } ::= { atmIfVptUniProvEntry 2 } atmIfVptUniSoftPvcRetryPeriod OBJECT-TYPE SYNTAX Unsigned32 (20..999999) ACCESS read-write STATUS obsolete DESCRIPTION "This attribute represents the time in seconds to wait between call set up retries. The resolution is to the nearest 10 seconds. This attribute has been obsoleted and is replaced by the softPvpAndPvcRetryPeriod attribute." DEFVAL { 60 } ::= { atmIfVptUniProvEntry 3 } atmIfVptUniSoftPvpAndPvcRetryPeriod OBJECT-TYPE SYNTAX Unsigned32 (20..999999) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute represents the time in seconds to wait between soft PVP or soft PVC call setup retries. The resolution is to the nearest 10 seconds." DEFVAL { 60 } ::= { atmIfVptUniProvEntry 4 } atmIfVptUniSoftPvpAndPvcHoldOffTime OBJECT-TYPE SYNTAX Unsigned32 (0 | 50..20000) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies how long to hold off retries following a release or the connection. The resolution is to the nearest 50 ms." DEFVAL { 0 } ::= { atmIfVptUniProvEntry 5 } atmIfVptUniAcctOptTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptUniAcctOptEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the provisionable attributes for accounting." ::= { atmIfVptUni 11 } atmIfVptUniAcctOptEntry OBJECT-TYPE SYNTAX AtmIfVptUniAcctOptEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfVptUniAcctOptTable." INDEX { atmIfIndex, atmIfVptIndex, atmIfVptUniIndex } ::= { atmIfVptUniAcctOptTable 1 } AtmIfVptUniAcctOptEntry ::= SEQUENCE { atmIfVptUniAccountCollection OCTET STRING, atmIfVptUniAccountConnectionType INTEGER, atmIfVptUniAccountClass Unsigned32, atmIfVptUniServiceExchange Unsigned32 } atmIfVptUniAccountCollection OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute is used to turn accounting on or off for SVC and SPVC connections. It also specifies the reason(s) for which accounting data is collected: billing, test, study, audit or force. If the set of reasons is not empty then accounting records will be generated by this interface in the following situations: - on a TODA changeover if TODA is enabled; - every 12 hours (per connection) if TODA is disabled; - on every call clear (a call record with final cell counts). If none of the reasons is present, then accounting will be suppressed. The reason for collection is recorded in the accounting record, in the attribute callingCollectReason or calledCollectReason as appropriate. Description of bits: bill(0) test(1) study(2) audit(3) force(4)" ::= { atmIfVptUniAcctOptEntry 1 } atmIfVptUniAccountConnectionType OBJECT-TYPE SYNTAX INTEGER { origTerm(0), intermediate(1) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies whether accounting records generated by this interface should be marked as originating, terminating or intermediate. This attribute, in combination with the direction of the call, determines the value of attribute connPointType of the accounting record and may be used by downstream accounting processes to correlate the records. If the value is origTerm then records generated for incoming calls will be marked as originating and records generated for outgoing calls will be marked as terminating. If the value is intermediate then records generated for all calls will be marked as intermediate." DEFVAL { origTerm } ::= { atmIfVptUniAcctOptEntry 2 } atmIfVptUniAccountClass OBJECT-TYPE SYNTAX Unsigned32 (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the accounting class associated with the interface. Its meaning is determined by the network operator. Its value is simply recorded in the accounting records generated by this interface, in the attribute callingServiceType or calledServiceType as appropriate." DEFVAL { 0 } ::= { atmIfVptUniAcctOptEntry 3 } atmIfVptUniServiceExchange OBJECT-TYPE SYNTAX Unsigned32 (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the data service exchange associated with this interface. Its meaning is determined by the network operator. Its value is simply recorded in the accounting records generated by this interface, in the attribute callingDse or calledDse as appropriate." DEFVAL { 0 } ::= { atmIfVptUniAcctOptEntry 4 } atmIfVptUniVProvTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptUniVProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the provisionable attributes for the Uni component which are specific to virtual UNI interfaces." ::= { atmIfVptUni 12 } atmIfVptUniVProvEntry OBJECT-TYPE SYNTAX AtmIfVptUniVProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfVptUniVProvTable." INDEX { atmIfIndex, atmIfVptIndex, atmIfVptUniIndex } ::= { atmIfVptUniVProvTable 1 } AtmIfVptUniVProvEntry ::= SEQUENCE { atmIfVptUniVpci Unsigned32 } atmIfVptUniVpci OBJECT-TYPE SYNTAX Unsigned32 (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the Virtual Path Connection Identifier (VPCI) to be used between this signalling entity and its peer. The VPCI of the peer virtual UNI must have the same value for switched connections to be set up across the interface." DEFVAL { 0 } ::= { atmIfVptUniVProvEntry 1 } -- AtmIf/n Iisp Signalling -- AtmIf/n Uni Signalling -- AtmIf/n Pnni Signalling -- AtmIf/n Vpt/m Iisp Signalling -- AtmIf/n Vpt/m Uni Signalling -- AtmIf/n Vpt/m Pnni Signalling -- -- This component represents the signalling entities for the interface. atmIfVptUniSig OBJECT IDENTIFIER ::= { atmIfVptUni 2 } atmIfVptUniSigRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptUniSigRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of atmIfVptUniSig components." ::= { atmIfVptUniSig 1 } atmIfVptUniSigRowStatusEntry OBJECT-TYPE SYNTAX AtmIfVptUniSigRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single atmIfVptUniSig component." INDEX { atmIfIndex, atmIfVptIndex, atmIfVptUniIndex, atmIfVptUniSigIndex } ::= { atmIfVptUniSigRowStatusTable 1 } AtmIfVptUniSigRowStatusEntry ::= SEQUENCE { atmIfVptUniSigRowStatus RowStatus, atmIfVptUniSigComponentName DisplayString, atmIfVptUniSigStorageType StorageType, atmIfVptUniSigIndex NonReplicated } atmIfVptUniSigRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of atmIfVptUniSig components. These components cannot be added nor deleted." ::= { atmIfVptUniSigRowStatusEntry 1 } atmIfVptUniSigComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { atmIfVptUniSigRowStatusEntry 2 } atmIfVptUniSigStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the atmIfVptUniSig tables." ::= { atmIfVptUniSigRowStatusEntry 4 } atmIfVptUniSigIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the atmIfVptUniSig tables." ::= { atmIfVptUniSigRowStatusEntry 10 } atmIfVptUniSigProvTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptUniSigProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute group contains the provisionable attributes for the Signalling component." ::= { atmIfVptUniSig 10 } atmIfVptUniSigProvEntry OBJECT-TYPE SYNTAX AtmIfVptUniSigProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfVptUniSigProvTable." INDEX { atmIfIndex, atmIfVptIndex, atmIfVptUniIndex, atmIfVptUniSigIndex } ::= { atmIfVptUniSigProvTable 1 } AtmIfVptUniSigProvEntry ::= SEQUENCE { atmIfVptUniSigVci Unsigned32, atmIfVptUniSigAddressConversion INTEGER } atmIfVptUniSigVci OBJECT-TYPE SYNTAX Unsigned32 (0..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the signalling channel number." DEFVAL { 5 } ::= { atmIfVptUniSigProvEntry 1 } atmIfVptUniSigAddressConversion OBJECT-TYPE SYNTAX INTEGER { none(0), nativeE164(1), nsap(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the address conversion on the outgoing signalling PDUs. The options are none, nativeE164, or nsap. The none option is the default and if this option is chosen then nothing is done to the address information element (IE) in the outgoing signalling message. If nativeE164 option is chosen, then only NSAP encapsulated E.164 addresses with zeros in the ESI are converted to native E.164 format in the outgoing signalling message. If the NSAP address is not encapsulated E.164 or the ESI field is not zeros and the nativeE164 option is chosen, then the call is cleared. If the nsap option is chosen, then native E.164 addresses are converted to NSAP E.164 with zeros in the ESI field; otherwise the address is in NSAP format and is not changed." DEFVAL { none } ::= { atmIfVptUniSigProvEntry 2 } atmIfVptUniSigStateTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptUniSigStateEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide." ::= { atmIfVptUniSig 11 } atmIfVptUniSigStateEntry OBJECT-TYPE SYNTAX AtmIfVptUniSigStateEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfVptUniSigStateTable." INDEX { atmIfIndex, atmIfVptIndex, atmIfVptUniIndex, atmIfVptUniSigIndex } ::= { atmIfVptUniSigStateTable 1 } AtmIfVptUniSigStateEntry ::= SEQUENCE { atmIfVptUniSigAdminState INTEGER, atmIfVptUniSigOperationalState INTEGER, atmIfVptUniSigUsageState INTEGER } atmIfVptUniSigAdminState OBJECT-TYPE SYNTAX INTEGER { locked(0), unlocked(1), shuttingDown(2) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component." DEFVAL { unlocked } ::= { atmIfVptUniSigStateEntry 1 } atmIfVptUniSigOperationalState OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle." DEFVAL { disabled } ::= { atmIfVptUniSigStateEntry 2 } atmIfVptUniSigUsageState OBJECT-TYPE SYNTAX INTEGER { idle(0), active(1), busy(2) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time." DEFVAL { idle } ::= { atmIfVptUniSigStateEntry 3 } atmIfVptUniSigOperTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptUniSigOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute contains the operational attributes for the AtmSignalling component." ::= { atmIfVptUniSig 12 } atmIfVptUniSigOperEntry OBJECT-TYPE SYNTAX AtmIfVptUniSigOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfVptUniSigOperTable." INDEX { atmIfIndex, atmIfVptIndex, atmIfVptUniIndex, atmIfVptUniSigIndex } ::= { atmIfVptUniSigOperTable 1 } AtmIfVptUniSigOperEntry ::= SEQUENCE { atmIfVptUniSigLastTxCauseCode Unsigned32, atmIfVptUniSigLastTxDiagCode Hex, atmIfVptUniSigLastRxCauseCode Unsigned32, atmIfVptUniSigLastRxDiagCode Hex } atmIfVptUniSigLastTxCauseCode OBJECT-TYPE SYNTAX Unsigned32 (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the cause code in the last transmitted signalling message that contains the CAUSE information element. The cause code is used to describe the reason for generating certain signalling messages." ::= { atmIfVptUniSigOperEntry 1 } atmIfVptUniSigLastTxDiagCode OBJECT-TYPE SYNTAX Hex (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute contains the diagnostic code in the last transmitted signalling message. The diagnostic code is contained in the CAUSE information element and identifies an information element type or timer type. The diagnostic code is present only if a procedural error is detected by the signalling protocol. A diagnostic code is always accompanied by the cause code. If there is no failure, this attribute is set to 0." ::= { atmIfVptUniSigOperEntry 2 } atmIfVptUniSigLastRxCauseCode OBJECT-TYPE SYNTAX Unsigned32 (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute contains the cause code in the last received signalling message that contains the CAUSE information element. The cause code is used to describe the reason for generating certain signalling messages." ::= { atmIfVptUniSigOperEntry 3 } atmIfVptUniSigLastRxDiagCode OBJECT-TYPE SYNTAX Hex (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute contains the diagnostic code in the last received signalling message. The diagnostic code is contained in the CAUSE information element and identifies an information element type or timer type. The diagnostic code is present only if a procedural error is detected by the signalling protocol. A diagnostic code is always accompanied by the cause code. If there is no failure, this attribute is set to 0." ::= { atmIfVptUniSigOperEntry 4 } atmIfVptUniSigStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptUniSigStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute group contains the statistics associated with the AtmSignalling component." ::= { atmIfVptUniSig 13 } atmIfVptUniSigStatsEntry OBJECT-TYPE SYNTAX AtmIfVptUniSigStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfVptUniSigStatsTable." INDEX { atmIfIndex, atmIfVptIndex, atmIfVptUniIndex, atmIfVptUniSigIndex } ::= { atmIfVptUniSigStatsTable 1 } AtmIfVptUniSigStatsEntry ::= SEQUENCE { atmIfVptUniSigCurrentConnections Counter32, atmIfVptUniSigPeakConnections Gauge32, atmIfVptUniSigSuccessfulConnections Counter32, atmIfVptUniSigFailedConnections Counter32, atmIfVptUniSigTxPdus Counter32, atmIfVptUniSigRxPdus Counter32, atmIfVptUniSigCurrentPmpConnections Gauge32, atmIfVptUniSigPeakPmpConnections Gauge32, atmIfVptUniSigSuccessfulPmpConnections Counter32, atmIfVptUniSigFailedPmpConnections Counter32, atmIfVptUniSigNewCurrentConnections Gauge32 } atmIfVptUniSigCurrentConnections OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS obsolete DESCRIPTION "This attribute indicates the total number of currently active connections." ::= { atmIfVptUniSigStatsEntry 1 } atmIfVptUniSigPeakConnections OBJECT-TYPE SYNTAX Gauge32 (0..4294967295) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the high water mark of active point-to- point and point-to-multipoint connections." ::= { atmIfVptUniSigStatsEntry 2 } atmIfVptUniSigSuccessfulConnections OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the total number of switched point-to- point and point-to-multipoint connections that were successfully established. The counter wraps to 0 when the maximum value is exceeded." ::= { atmIfVptUniSigStatsEntry 3 } atmIfVptUniSigFailedConnections OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the total number of switched connections that were not successfully established.The counter wraps to 0 when the maximum value is exceeded." ::= { atmIfVptUniSigStatsEntry 4 } atmIfVptUniSigTxPdus OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the number of transmitted signalling PDUs.The counter wraps to 0 when the maximum value is exceeded." ::= { atmIfVptUniSigStatsEntry 5 } atmIfVptUniSigRxPdus OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the number of received signalling PDUs.The counter wraps to 0 when the maximum value is exceeded." ::= { atmIfVptUniSigStatsEntry 6 } atmIfVptUniSigCurrentPmpConnections OBJECT-TYPE SYNTAX Gauge32 (0..4294967295) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the number of currently active point-to- multipoint connections." ::= { atmIfVptUniSigStatsEntry 7 } atmIfVptUniSigPeakPmpConnections OBJECT-TYPE SYNTAX Gauge32 (0..4294967295) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the high water mark of active point-to- multipoint connections." ::= { atmIfVptUniSigStatsEntry 8 } atmIfVptUniSigSuccessfulPmpConnections OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the total number of switched point-to- multipoint connections that were successfully established. The counter wraps to 0 when the maximum value is exceeded." ::= { atmIfVptUniSigStatsEntry 9 } atmIfVptUniSigFailedPmpConnections OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the number of switched point-to- multipoint connections that were not successfully established.The counter wraps to 0 when the maximum value is exceeded." ::= { atmIfVptUniSigStatsEntry 10 } atmIfVptUniSigNewCurrentConnections OBJECT-TYPE SYNTAX Gauge32 (0..4294967295) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the total number of currently active point-to- point and point-to-multipoint connections." ::= { atmIfVptUniSigStatsEntry 11 } -- AtmIf/n Uni Sig VirtualChannelDescriptor -- AtmIf/n Uni Ilmi VirtualChannelDescriptor -- AtmIf/n Iisp Sig VirtualChannelDescriptor -- AtmIf/n Pnni Sig VirtualChannelDescriptor -- AtmIf/n Pnni Rcc VirtualChannelDescriptor -- AtmIf/n Vpt/m Uni Sig VirtualChannelDescriptor -- AtmIf/n Vpt/m Iisp Sig VirtualChannelDescriptor -- AtmIf/n Vpt/m Pnni Sig VirtualChannelDescriptor -- AtmIf/n Vpt/m Pnni Rcc VirtualChannelDescriptor -- -- This component contains the provisionable traffic parameters for a -- control channel (Sig, Ilmi or Rcc component). atmIfVptUniSigVcd OBJECT IDENTIFIER ::= { atmIfVptUniSig 2 } atmIfVptUniSigVcdRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptUniSigVcdRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of atmIfVptUniSigVcd components." ::= { atmIfVptUniSigVcd 1 } atmIfVptUniSigVcdRowStatusEntry OBJECT-TYPE SYNTAX AtmIfVptUniSigVcdRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single atmIfVptUniSigVcd component." INDEX { atmIfIndex, atmIfVptIndex, atmIfVptUniIndex, atmIfVptUniSigIndex, atmIfVptUniSigVcdIndex } ::= { atmIfVptUniSigVcdRowStatusTable 1 } AtmIfVptUniSigVcdRowStatusEntry ::= SEQUENCE { atmIfVptUniSigVcdRowStatus RowStatus, atmIfVptUniSigVcdComponentName DisplayString, atmIfVptUniSigVcdStorageType StorageType, atmIfVptUniSigVcdIndex NonReplicated } atmIfVptUniSigVcdRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-write STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of atmIfVptUniSigVcd components. These components can be added and deleted." ::= { atmIfVptUniSigVcdRowStatusEntry 1 } atmIfVptUniSigVcdComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { atmIfVptUniSigVcdRowStatusEntry 2 } atmIfVptUniSigVcdStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the atmIfVptUniSigVcd tables." ::= { atmIfVptUniSigVcdRowStatusEntry 4 } atmIfVptUniSigVcdIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the atmIfVptUniSigVcd tables." ::= { atmIfVptUniSigVcdRowStatusEntry 10 } atmIfVptUniSigVcdProvTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptUniSigVcdProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the provisionable traffic attributes for a control channel." ::= { atmIfVptUniSigVcd 10 } atmIfVptUniSigVcdProvEntry OBJECT-TYPE SYNTAX AtmIfVptUniSigVcdProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfVptUniSigVcdProvTable." INDEX { atmIfIndex, atmIfVptIndex, atmIfVptUniIndex, atmIfVptUniSigIndex, atmIfVptUniSigVcdIndex } ::= { atmIfVptUniSigVcdProvTable 1 } AtmIfVptUniSigVcdProvEntry ::= SEQUENCE { atmIfVptUniSigVcdTrafficDescType INTEGER, atmIfVptUniSigVcdAtmServiceCategory INTEGER, atmIfVptUniSigVcdQosClass INTEGER, atmIfVptUniSigVcdTrafficShaping INTEGER, atmIfVptUniSigVcdUnshapedTransmitQueueing INTEGER, atmIfVptUniSigVcdUsageParameterControl INTEGER } atmIfVptUniSigVcdTrafficDescType OBJECT-TYPE SYNTAX INTEGER { n3(3), n6(6), n7(7), n8(8) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the type of traffic management which is applied to both the transmit and receive direction of this connection as defined in the ATM Forum. The trafficDescType determines the number and meaning of the parameters in the trafficDescParm attribute." DEFVAL { n6 } ::= { atmIfVptUniSigVcdProvEntry 1 } atmIfVptUniSigVcdAtmServiceCategory OBJECT-TYPE SYNTAX INTEGER { unspecifiedBitRate(0), constantBitRate(1), rtVariableBitRate(2), nrtVariableBitRate(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the ATM service category for both directions of the connection. The constantBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. The consistent availability of a fixed quantity of bandwidth is considered appropriate for CBR service. Cells which are delayed beyond the value specified by CellTransfer Delay are assumed to be of significantly reduce value to the application. The rtVariableBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. Sources are expected to transmit at a rate which varies with time. Equivalently, the source can be described as 'bursty'. Cells which are delayed beyond the value specified by CTD are assumed to be of significantly reduced value to the application. Real time VBR service may support statistical multiplexing of real time sources. The nrtVariableBitRate service category is intended for non-real time applications which have bursty traffic characteristics and which can be characterized in terms of a PCR, SCR, and MBS. For those cells which are transferred within the traffic contract, the application expects a low cell loss ratio. For all connections, it expects a bound on the mean cell transfer delay. Non-real time VBR service may support statistical multiplexing of connections. The unspecifiedBitRate service is intended for non-real time applications; that is, those not requiring tightly constrained delay and delay variation. UBR sources are expected to be bursty. UBR service supports a high degree of statistical multiplexing among sources. UBR service does not specify traffic related service guarantees. No numerical commitments are made with respect to the cell loss ratio experienced by a UBR connection, or as to the cell transfer delay experienced by cells on the connection." DEFVAL { rtVariableBitRate } ::= { atmIfVptUniSigVcdProvEntry 3 } atmIfVptUniSigVcdQosClass OBJECT-TYPE SYNTAX INTEGER { n0(0), n1(1), n2(2), n3(3), n4(4) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the quality of service for both the forward and backward direction for this connection. Class 1 supports a QOS that meets Service Class A performance requirements (Circuit emulation, constant bit rate video). Class 2 supports a QOS that meets Service Class B performance requirements (Variable bit rate audio and video). Class 3 supports a QOS that meets Service Class C performance requirements (Connection-Oriented Data Transfer). Class 4 supports a QOS that meets Service Class D performance requirements (Connectionless Data Transfer). Class 0 is the unspecified bit rate QOS class; no objective is specified for the performance parameters." DEFVAL { n2 } ::= { atmIfVptUniSigVcdProvEntry 21 } atmIfVptUniSigVcdTrafficShaping OBJECT-TYPE SYNTAX INTEGER { disabled(1), sameAsCa(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies whether this connection uses traffic shaping when transmitting traffic to the ATM interface. When sameAsCa is selected, traffic shaping for this connection is based on the trafficShaping attribute of the connection's service category component under the AtmIf CA. If the service category has traffic shaping enabled, then traffic shaping is enabled for the connection. Note that enabling traffic shaping may have no effect under certain cases. These cases are listed in the description of the trafficShaping operational attribute, which is under the Vcc Tm and Vpc Tm components. When disabled is selected, traffic shaping for this connection is disabled." DEFVAL { disabled } ::= { atmIfVptUniSigVcdProvEntry 50 } atmIfVptUniSigVcdUnshapedTransmitQueueing OBJECT-TYPE SYNTAX INTEGER { common(1), sameAsCa(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute only applies when this connection is unshaped. This attribute specifies the transmit queueing method for this connection if it is unshaped. Refer to the unshapedTransmitQueueing attribute under the AtmIf CA service category subcomponent for more details on the meaning of this attribute. When this attribute is set to sameAsCa, the transmit queueing method for the connection is based on the unshapedTransmitQueueing attribute of the connection's service category component under the ConnectionAdministrator. When this attribute is set to common, transmit traffic on this unshaped connection is destined for the common queue. The value sameAsInterface is for migration from previous software releases, but should no longer be used" DEFVAL { sameAsCa } ::= { atmIfVptUniSigVcdProvEntry 60 } atmIfVptUniSigVcdUsageParameterControl OBJECT-TYPE SYNTAX INTEGER { disabled(1), sameAsCa(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies whether this connection enforces usage parameter control when receiving traffic from the ATM interface. When sameAsCa is selected, UPC for the connection is based on the usageParameterControl attribute of the connection's service category component under the ConnectionAdministrator. If the service category has UPC enabled, then UPC is enabled for the connection. Note that enabling UPC may have no effect under certain cases. These cases are listed in the description of the usageParameterControl operational attribute, which is under the Vcc Tm or Vpc Tm component. When disabled is selected, UPC for this connection is disabled. The value sameAsInterface is for migration from previous software releases, but should no longer be used" DEFVAL { disabled } ::= { atmIfVptUniSigVcdProvEntry 70 } atmIfVptUniSigVcdTdpTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptUniSigVcdTdpEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute is a vector of five traffic parameters whose meanings are defined by the trafficDescType attribute. The values of peak cell rate (PCR), sustained cell rate (SCR) and requested shaping rate are expressed in cell/s. Maximum burst size (MBS) is expressed in cells. CDVT is expressed in microseconds. The values of PCR, SCR, MBS and CDVT are used for connection admission control (CAC). The value of CDVT is only used for connections where the atmServiceCategory is constantBitRate. For all other values of atmServiceCategory, CDVT is ignored. The values of PCR, SCR and requested shaping rate are used to determine the actual shaping rate where traffic shaping is enabled. When trafficDescType is 3, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameter 1 must be non-zero. Parameters 2 and 3 must be zero. When trafficDescType is 6, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 and 1 traffic; parameter 3 represents the MBS for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. When trafficDescType is 7, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 with cell discard; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. When trafficDescType is 8, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 traffic with cell tagging; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. Whenever it is valid for PCR to be specified, parameter 5 may also be used to specify a requested shaping rate. A non-zero value in parameter 5 overrides the value in parameter 1 and is used as the peak cell rate in calculations of CAC and shaping rate. For trafficDescType 3 the traffic is shaped at the next rate less than the PCR. For trafficDescType 6, 7, and 8, the traffic is shaped at the highest available rate which is between PCR and SCR. However, if there is no available shaping rate between PCR and SCR, traffic is shaped at the next rate above the PCR." ::= { atmIfVptUniSigVcd 387 } atmIfVptUniSigVcdTdpEntry OBJECT-TYPE SYNTAX AtmIfVptUniSigVcdTdpEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfVptUniSigVcdTdpTable." INDEX { atmIfIndex, atmIfVptIndex, atmIfVptUniIndex, atmIfVptUniSigIndex, atmIfVptUniSigVcdIndex, atmIfVptUniSigVcdTdpIndex } ::= { atmIfVptUniSigVcdTdpTable 1 } AtmIfVptUniSigVcdTdpEntry ::= SEQUENCE { atmIfVptUniSigVcdTdpIndex Integer32, atmIfVptUniSigVcdTdpValue Unsigned32 } atmIfVptUniSigVcdTdpIndex OBJECT-TYPE SYNTAX Integer32 (1..5) ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the atmIfVptUniSigVcdTdpTable specific index for the atmIfVptUniSigVcdTdpTable." ::= { atmIfVptUniSigVcdTdpEntry 1 } atmIfVptUniSigVcdTdpValue OBJECT-TYPE SYNTAX Unsigned32 (0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "This variable represents an individual value for the atmIfVptUniSigVcdTdpTable." ::= { atmIfVptUniSigVcdTdpEntry 2 } -- AtmIf/n Iisp Address/address,type -- AtmIf/n Uni Address/address,type -- AtmIf/n Pnni Address/address,type -- AtmIf/n Vpt/m Iisp Address/address,type -- AtmIf/n Vpt/m Uni Address/address,type -- AtmIf/n Vpt/m Pnni Address/address,type -- -- This component represents an address (dynamic or static) -- associated with the interface. The index is a string of 1 to 40 hex -- digits or a single wildcard ('?'), and a type. The type identifies -- whether the Address component is for a primary, alternate, -- registered, or default address. -- -- The types primary and alternate are used for provisioned addresses. -- The type registered is used for dynamic addresses registered -- through ILMI. The type default is used for Soft PVP and Soft PVC -- addresses.Virtual interfaces do not have addresses of -- type default. -- -- The wildcard is only valid for provisioned addresses. If the address -- is a single wildcard, then that indicates that the interface supports -- all addresses. If there is no better match, then this interface may be -- chosen in the routing. If there is more than one interface with a -- single wildcard static address, then the choice is driven through a -- round robin algorithm. -- -- The round robin algorithm tries the primary routes and then the -- alternate routes if none of the primary routes succeed. -- If this node participates in a PNNI hierarchy, then a PnniInfo -- subcomponent can be provisioned under the AtmAddress -- component to specify the level to which this address will be -- advertised. atmIfVptUniAddr OBJECT IDENTIFIER ::= { atmIfVptUni 3 } atmIfVptUniAddrRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptUniAddrRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of atmIfVptUniAddr components." ::= { atmIfVptUniAddr 1 } atmIfVptUniAddrRowStatusEntry OBJECT-TYPE SYNTAX AtmIfVptUniAddrRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single atmIfVptUniAddr component." INDEX { atmIfIndex, atmIfVptIndex, atmIfVptUniIndex, atmIfVptUniAddrAddressIndex, atmIfVptUniAddrAddressTypeIndex } ::= { atmIfVptUniAddrRowStatusTable 1 } AtmIfVptUniAddrRowStatusEntry ::= SEQUENCE { atmIfVptUniAddrRowStatus RowStatus, atmIfVptUniAddrComponentName DisplayString, atmIfVptUniAddrStorageType StorageType, atmIfVptUniAddrAddressIndex AsciiStringIndex, atmIfVptUniAddrAddressTypeIndex INTEGER } atmIfVptUniAddrRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-write STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of atmIfVptUniAddr components. These components can be added and deleted." ::= { atmIfVptUniAddrRowStatusEntry 1 } atmIfVptUniAddrComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { atmIfVptUniAddrRowStatusEntry 2 } atmIfVptUniAddrStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the atmIfVptUniAddr tables." ::= { atmIfVptUniAddrRowStatusEntry 4 } atmIfVptUniAddrAddressIndex OBJECT-TYPE SYNTAX AsciiStringIndex (SIZE (1..40)) ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents an index for the atmIfVptUniAddr tables." ::= { atmIfVptUniAddrRowStatusEntry 10 } atmIfVptUniAddrAddressTypeIndex OBJECT-TYPE SYNTAX INTEGER { primary(0), alternate(1), registered(2), default(3) } ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents an index for the atmIfVptUniAddr tables." ::= { atmIfVptUniAddrRowStatusEntry 11 } atmIfVptUniAddrOperTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptUniAddrOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute group contains the operational attributes for the Address component." ::= { atmIfVptUniAddr 10 } atmIfVptUniAddrOperEntry OBJECT-TYPE SYNTAX AtmIfVptUniAddrOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfVptUniAddrOperTable." INDEX { atmIfIndex, atmIfVptIndex, atmIfVptUniIndex, atmIfVptUniAddrAddressIndex, atmIfVptUniAddrAddressTypeIndex } ::= { atmIfVptUniAddrOperTable 1 } AtmIfVptUniAddrOperEntry ::= SEQUENCE { atmIfVptUniAddrScope INTEGER, atmIfVptUniAddrReachability INTEGER } atmIfVptUniAddrScope OBJECT-TYPE SYNTAX INTEGER (-1..104) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the scope of the ATM address, which is the highest level to which this address will be advertised in the PNNI hierarchy. If no PnniInfo subcomponent has been provisioned, then the scope will default to the level of this node in the PNNI hierarchy. If this node does not participate in a PNNI hierarchy, then this attribute will have the value of -1." ::= { atmIfVptUniAddrOperEntry 1 } atmIfVptUniAddrReachability OBJECT-TYPE SYNTAX INTEGER { internal(0), exterior(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates whether the address is internal or exterior. An internal reachable address is an address of a destination that is directly attached to the logical node advertising the address. An exterior reachable address is an address that can be reached through a PNNI routing domain, but which is not located in that PNNI routing domain." ::= { atmIfVptUniAddrOperEntry 2 } -- AtmIf/n Iisp Address/address,type TerminateSPvpAndSPvc -- AtmIf/n Uni Address/address,type TerminateSPvpAndSPvc -- AtmIf/n Pnni Address/address,type TerminateSPvpAndSPvc -- AtmIf/n Vpt/m Iisp Address/address,type TerminateSPvpAndSPvc -- AtmIf/n Vpt/m Uni Address/address,type TerminateSPvpAndSPvc -- AtmIf/n Vpt/m Pnni Address/address,type TerminateSPvpAndSPvc -- -- The presence of this subcomponent indicates that SPvp and SPvc -- call setups terminate at this node if the destination address of the -- SPVP or SPVC matches the Address instance. atmIfVptUniAddrTermSP OBJECT IDENTIFIER ::= { atmIfVptUniAddr 2 } atmIfVptUniAddrTermSPRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptUniAddrTermSPRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of atmIfVptUniAddrTermSP components." ::= { atmIfVptUniAddrTermSP 1 } atmIfVptUniAddrTermSPRowStatusEntry OBJECT-TYPE SYNTAX AtmIfVptUniAddrTermSPRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single atmIfVptUniAddrTermSP component." INDEX { atmIfIndex, atmIfVptIndex, atmIfVptUniIndex, atmIfVptUniAddrAddressIndex, atmIfVptUniAddrAddressTypeIndex, atmIfVptUniAddrTermSPIndex } ::= { atmIfVptUniAddrTermSPRowStatusTable 1 } AtmIfVptUniAddrTermSPRowStatusEntry ::= SEQUENCE { atmIfVptUniAddrTermSPRowStatus RowStatus, atmIfVptUniAddrTermSPComponentName DisplayString, atmIfVptUniAddrTermSPStorageType StorageType, atmIfVptUniAddrTermSPIndex NonReplicated } atmIfVptUniAddrTermSPRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-write STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of atmIfVptUniAddrTermSP components. These components can be added and deleted." ::= { atmIfVptUniAddrTermSPRowStatusEntry 1 } atmIfVptUniAddrTermSPComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { atmIfVptUniAddrTermSPRowStatusEntry 2 } atmIfVptUniAddrTermSPStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the atmIfVptUniAddrTermSP tables." ::= { atmIfVptUniAddrTermSPRowStatusEntry 4 } atmIfVptUniAddrTermSPIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the atmIfVptUniAddrTermSP tables." ::= { atmIfVptUniAddrTermSPRowStatusEntry 10 } -- AtmIf/n Iisp Addr/address,type PnniInfo -- AtmIf/n Uni Addr/address,type PnniInfo -- AtmIf/n Pnni Addr/address,type PnniInfo -- AtmIf/n Vpt/m Iisp Addr/address,type PnniInfo -- AtmIf/n Vpt/m Uni Addr/address,type PnniInfo -- AtmIf/n Vpt/m Pnni Addr/address,type PnniInfo -- -- This component contains provisioned information associated with -- the ATM address related to PNNI. This component appears only -- under provisioned Address components. atmIfVptUniAddrPnniInfo OBJECT IDENTIFIER ::= { atmIfVptUniAddr 3 } atmIfVptUniAddrPnniInfoRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptUniAddrPnniInfoRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of atmIfVptUniAddrPnniInfo components." ::= { atmIfVptUniAddrPnniInfo 1 } atmIfVptUniAddrPnniInfoRowStatusEntry OBJECT-TYPE SYNTAX AtmIfVptUniAddrPnniInfoRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single atmIfVptUniAddrPnniInfo component." INDEX { atmIfIndex, atmIfVptIndex, atmIfVptUniIndex, atmIfVptUniAddrAddressIndex, atmIfVptUniAddrAddressTypeIndex, atmIfVptUniAddrPnniInfoIndex } ::= { atmIfVptUniAddrPnniInfoRowStatusTable 1 } AtmIfVptUniAddrPnniInfoRowStatusEntry ::= SEQUENCE { atmIfVptUniAddrPnniInfoRowStatus RowStatus, atmIfVptUniAddrPnniInfoComponentName DisplayString, atmIfVptUniAddrPnniInfoStorageType StorageType, atmIfVptUniAddrPnniInfoIndex NonReplicated } atmIfVptUniAddrPnniInfoRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-write STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of atmIfVptUniAddrPnniInfo components. These components can be added and deleted." ::= { atmIfVptUniAddrPnniInfoRowStatusEntry 1 } atmIfVptUniAddrPnniInfoComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { atmIfVptUniAddrPnniInfoRowStatusEntry 2 } atmIfVptUniAddrPnniInfoStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the atmIfVptUniAddrPnniInfo tables." ::= { atmIfVptUniAddrPnniInfoRowStatusEntry 4 } atmIfVptUniAddrPnniInfoIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the atmIfVptUniAddrPnniInfo tables." ::= { atmIfVptUniAddrPnniInfoRowStatusEntry 10 } atmIfVptUniAddrPnniInfoProvTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptUniAddrPnniInfoProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute group contains the provisioned attributes relating to PNNI for a PnniInfo component." ::= { atmIfVptUniAddrPnniInfo 10 } atmIfVptUniAddrPnniInfoProvEntry OBJECT-TYPE SYNTAX AtmIfVptUniAddrPnniInfoProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfVptUniAddrPnniInfoProvTable." INDEX { atmIfIndex, atmIfVptIndex, atmIfVptUniIndex, atmIfVptUniAddrAddressIndex, atmIfVptUniAddrAddressTypeIndex, atmIfVptUniAddrPnniInfoIndex } ::= { atmIfVptUniAddrPnniInfoProvTable 1 } AtmIfVptUniAddrPnniInfoProvEntry ::= SEQUENCE { atmIfVptUniAddrPnniInfoScope INTEGER, atmIfVptUniAddrPnniInfoReachability INTEGER } atmIfVptUniAddrPnniInfoScope OBJECT-TYPE SYNTAX INTEGER (-1..104) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the scope of the ATM address, which is the highest level up to which this address will be advertised in the PNNI hierarchy. The scope must be set to a value numerically less than or equal to the level of the lowest level peer group containing this node. Setting the scope to 0 will cause the address to be advertised globally within this PNNI routing domain." DEFVAL { -1 } ::= { atmIfVptUniAddrPnniInfoProvEntry 1 } atmIfVptUniAddrPnniInfoReachability OBJECT-TYPE SYNTAX INTEGER { internal(0), exterior(1) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute indicates whether the address is internal or exterior. An internal reachable address is an address of a destination that is directly attached to the logical node advertising the address. An exterior reachable address is an address that can be reached through a PNNI routing domain, but which is not located in that PNNI routing domain." DEFVAL { internal } ::= { atmIfVptUniAddrPnniInfoProvEntry 2 } -- -- Version and Compliance statements -- -- Object-Group Statement: -- A list of all current accessible leaf objects. -- OBJECTS { atmIfVptUniSigSuccessfulConnections, -- atmIfVptUniAddrPnniInfoRowStatus, -- atmIfUniSigFailedConnections, -- atmIfUniAddrScope, -- atmIfVptUniSigVcdUsageParameterControl, -- atmIfUniSigVcdQosClass, -- atmIfVptUniSoftPvpAndPvcRetryPeriod, -- atmIfUniSigLastTxDiagCode, -- atmIfUniSigOperationalState, -- atmIfVptUniAddrStorageType, -- atmIfVptUniStorageType, -- atmIfUniSigCurrentPmpConnections, -- atmIfUniSigVci, -- atmIfUniAddrTermSPComponentName, -- atmIfUniVersion, -- atmIfUniSigVcdComponentName, -- atmIfVptUniSigLastTxDiagCode, -- atmIfVptUniSide, -- atmIfUniIlmiVci, -- atmIfUniMacAddress, -- atmIfVptUniAddrPnniInfoStorageType, -- atmIfVptUniSigFailedConnections, -- atmIfUniAddrPnniInfoComponentName, -- atmIfVptUniSigVcdTrafficDescType, -- atmIfUniIlmiComponentName, -- atmIfUniSigRxPdus, -- atmIfUniAddrPnniInfoReachability, -- atmIfUniSigLastRxDiagCode, -- atmIfVptUniRowStatus, -- atmIfUniSigLastTxCauseCode, -- atmIfUniIlmiRxPdus, -- atmIfVptUniSoftPvpAndPvcHoldOffTime, -- atmIfVptUniAddrTermSPStorageType, -- atmIfVptUniSigPeakConnections, -- atmIfUniSigSuccessfulConnections, -- atmIfVptUniSigVcdAtmServiceCategory, -- atmIfUniIlmiEsiToRegisterRowStatus, -- atmIfVptUniSigStorageType, -- atmIfVptUniSigVcdTrafficShaping, -- atmIfVptUniServiceExchange, -- atmIfUniSigNewCurrentConnections, -- atmIfVptUniAddrReachability, -- atmIfVptUniSigAdminState, -- atmIfUniIlmiEsiToRegisterValue, -- atmIfUniIlmiRxBadPdusDiscarded, -- atmIfUniSigVcdTdpValue, -- atmIfVptUniSigVcdTdpValue, -- atmIfUniAddrComponentName, -- atmIfUniComponentName, -- atmIfVptUniSigRowStatus, -- atmIfUniSigPeakPmpConnections, -- atmIfUniSigRowStatus, -- atmIfUniAddrTermSPStorageType, -- atmIfUniSigVcdStorageType, -- atmIfUniSigPeakConnections, -- atmIfVptUniAddrPnniInfoScope, -- atmIfUniSigTxPdus, -- atmIfVptUniAddrComponentName, -- atmIfUniAccountConnectionType, -- atmIfVptUniSigUsageState, -- atmIfUniSigFailedPmpConnections, -- atmIfUniIlmiStorageType, -- atmIfVptUniSigVcdStorageType, -- atmIfVptUniSigLastRxCauseCode, -- atmIfVptUniSigTxPdus, -- atmIfVptUniAddrScope, -- atmIfUniAddrPnniInfoStorageType, -- atmIfUniIlmiTxPdus, -- atmIfVptUniSigVcdQosClass, -- atmIfUniSigVcdUnshapedTransmitQueueing, -- atmIfUniAddrTermSPRowStatus, -- atmIfUniSigComponentName, -- atmIfUniSigVcdRowStatus, -- atmIfVptUniSigCurrentPmpConnections, -- atmIfUniIlmiAdminState, -- atmIfUniAccountClass, -- atmIfVptUniAddrTermSPComponentName, -- atmIfVptUniSigVcdComponentName, -- atmIfUniAddrPnniInfoRowStatus, -- atmIfUniIlmiRowStatus, -- atmIfVptUniAddrPnniInfoComponentName, -- atmIfUniSide, -- atmIfUniAccountCollection, -- atmIfVptUniSigRxPdus, -- atmIfVptUniVersion, -- atmIfUniAddrStorageType, -- atmIfUniStorageType, -- atmIfUniIlmiUsageState, -- atmIfVptUniSigLastRxDiagCode, -- atmIfVptUniAccountCollection, -- atmIfVptUniSigLastTxCauseCode, -- atmIfVptUniSigPeakPmpConnections, -- atmIfUniSigSuccessfulPmpConnections, -- atmIfUniIlmiPrefixToRegisterRowStatus, -- atmIfUniIlmiOperatingMode, -- atmIfUniAddrReachability, -- atmIfUniAddrRowStatus, -- atmIfVptUniAddrPnniInfoReachability, -- atmIfUniSigVcdTrafficDescType, -- atmIfUniIlmiOperationalState, -- atmIfUniIlmiPrefixToRegisterValue, -- atmIfVptUniAddrRowStatus, -- atmIfVptUniSigNewCurrentConnections, -- atmIfUniSigVcdUsageParameterControl, -- atmIfUniRowStatus, -- atmIfUniSigVcdTrafficShaping, -- atmIfUniSigStorageType, -- atmIfUniSoftPvpAndPvcHoldOffTime, -- atmIfVptUniSigAddressConversion, -- atmIfVptUniComponentName, -- atmIfVptUniAccountClass, -- atmIfUniSoftPvpAndPvcRetryPeriod, -- atmIfVptUniVpci, -- atmIfUniSigVcdAtmServiceCategory, -- atmIfUniAddrPnniInfoScope, -- atmIfVptUniSigOperationalState, -- atmIfUniServiceExchange, -- atmIfVptUniAccountConnectionType, -- atmIfUniSigAdminState, -- atmIfVptUniSigFailedPmpConnections, -- atmIfVptUniSigVci, -- atmIfUniSigLastRxCauseCode, -- atmIfVptUniSigVcdUnshapedTransmitQueueing, -- atmIfVptUniAddrTermSPRowStatus, -- atmIfVptUniSigComponentName, -- atmIfVptUniSigVcdRowStatus, -- atmIfUniSigAddressConversion, -- atmIfVptUniSigSuccessfulPmpConnections, -- atmIfUniSigUsageState } -- STATUS mandatory -- DESCRIPTION -- "A list of all current accessible leaf objects." atmUniGroup OBJECT IDENTIFIER ::= { atmUniMIB 1 } atmUniGroupBE OBJECT IDENTIFIER ::= { atmUniGroup 5 } atmUniGroupBE00 OBJECT IDENTIFIER ::= { atmUniGroupBE 1 } atmUniGroupBE00A OBJECT IDENTIFIER ::= { atmUniGroupBE00 2 } -- Agent-Capabilities Statement: -- PRODUCT-RELEASE "Passport Release 7.0 AtmUni." -- STATUS mandatory -- DESCRIPTION "AtmUni MIB: MIB Version BE00A, -- Software Version BG00S4C." -- SUPPORTS Nortel-Magellan-Passport-AtmUniMIB -- INCLUDES { atmUniGroupBE00A } atmUniCapabilities OBJECT IDENTIFIER ::= { atmUniMIB 3 } atmUniCapabilitiesBE OBJECT IDENTIFIER ::= { atmUniCapabilities 5 } atmUniCapabilitiesBE00 OBJECT IDENTIFIER ::= { atmUniCapabilitiesBE 1 } atmUniCapabilitiesBE00A OBJECT IDENTIFIER ::= { atmUniCapabilitiesBE00 2 } END