Nortel-Magellan-Passport-AtmNetworkingMIB DEFINITIONS ::= BEGIN IMPORTS OBJECT-TYPE FROM RFC-1212 components, passportMIBs FROM Nortel-Magellan-Passport-UsefulDefinitionsMIB Counter32, RowPointer, DisplayString, StorageType, RowStatus, Gauge32, Integer32, Unsigned32 FROM Nortel-Magellan-Passport-StandardTextualConventionsMIB AsciiString, NonReplicated, HexString, FixedPoint1, AsciiStringIndex, IntegerSequence FROM Nortel-Magellan-Passport-TextualConventionsMIB atmIfVccIndex, atmIfVptIndex, atmIfVcc, atmIfVpcIndex, atmIfVpc, atmIfVptVccIndex, atmIfIndex, atmIfVptVcc FROM Nortel-Magellan-Passport-AtmCoreMIB; -- LAST-UPDATED "9904150000Z" -- ORGANIZATION "Nortel" -- CONTACT-INFO " -- Nortel Magellan Network Management -- -- Postal: P.O. Box 5080, Station F -- Ottawa, Ontario -- Canada K2C 3T1 -- -- Email: nm_plm@nt.com" -- DESCRIPTION -- "The module describing the Nortel Magellan Passport -- AtmNetworking Enterprise MIB." atmNetworkingMIB OBJECT IDENTIFIER ::= { passportMIBs 42 } -- AtmRouting -- This component contains the provisionable and operational -- attributes related to ATM PNNI routing. -- -- The Dna subcomponents can be listed to view all the provisioned -- and registered ATM end system addresses and prefixes stored -- against any of the Uni, Iisp or Pnni interfaces. -- -- The Pnni subcomponent can be provisioned to identify that this -- Passport node participates in a PNNI hierarchy. -- -- The ConfiguredNode subcomponents are indexed by level in the -- PNNI hierarchy (a value between 0 and 104), and define -- configuration information. aRtg OBJECT IDENTIFIER ::= { components 95 } aRtgRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of aRtg components." ::= { aRtg 1 } aRtgRowStatusEntry OBJECT-TYPE SYNTAX ARtgRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single aRtg component." INDEX { aRtgIndex } ::= { aRtgRowStatusTable 1 } ARtgRowStatusEntry ::= SEQUENCE { aRtgRowStatus RowStatus, aRtgComponentName DisplayString, aRtgStorageType StorageType, aRtgIndex NonReplicated } aRtgRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-write STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of aRtg components. These components can be added and deleted." ::= { aRtgRowStatusEntry 1 } aRtgComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { aRtgRowStatusEntry 2 } aRtgStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the aRtg tables." ::= { aRtgRowStatusEntry 4 } aRtgIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the aRtg tables." ::= { aRtgRowStatusEntry 10 } aRtgStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the statistical operational attributes of an ARtg component." ::= { aRtg 10 } aRtgStatsEntry OBJECT-TYPE SYNTAX ARtgStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the aRtgStatsTable." INDEX { aRtgIndex } ::= { aRtgStatsTable 1 } ARtgStatsEntry ::= SEQUENCE { aRtgRoutingAttempts Counter32, aRtgFailedRoutingAttempts Counter32 } aRtgRoutingAttempts OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the total number of calls routed. The counter wraps when it exceeds the maximum value." ::= { aRtgStatsEntry 1 } aRtgFailedRoutingAttempts OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the total number of calls which were not successfully routed.The counter wraps when it exceeds the maximum value." ::= { aRtgStatsEntry 2 } -- -- *** THIS SUBTREE CURRENTLY NOT IMPLEMENTED *** -- -- ARtg Dna/ -- This component represents an ATM NSAP address that has been -- provisioned or dynamically registered through ILMI. aRtgDna OBJECT IDENTIFIER ::= { aRtg 2 } aRtgDnaRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgDnaRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This entry controls the addition and deletion of aRtgDna components." ::= { aRtgDna 1 } aRtgDnaRowStatusEntry OBJECT-TYPE SYNTAX ARtgDnaRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single aRtgDna component." INDEX { aRtgIndex, aRtgDnaIndex } ::= { aRtgDnaRowStatusTable 1 } ARtgDnaRowStatusEntry ::= SEQUENCE { aRtgDnaRowStatus RowStatus, aRtgDnaComponentName DisplayString, aRtgDnaStorageType StorageType, aRtgDnaIndex AsciiStringIndex } aRtgDnaRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of aRtgDna components. These components cannot be added nor deleted." ::= { aRtgDnaRowStatusEntry 1 } aRtgDnaComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { aRtgDnaRowStatusEntry 2 } aRtgDnaStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the aRtgDna tables." ::= { aRtgDnaRowStatusEntry 4 } aRtgDnaIndex OBJECT-TYPE SYNTAX AsciiStringIndex (SIZE (1..40)) ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the aRtgDna tables." ::= { aRtgDnaRowStatusEntry 10 } -- -- *** THIS SUBTREE CURRENTLY NOT IMPLEMENTED *** -- -- ARtg Dna/ DestInfo/ -- This component represents a destination associated with the parent -- Dna. aRtgDnaDestInfo OBJECT IDENTIFIER ::= { aRtgDna 2 } aRtgDnaDestInfoRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgDnaDestInfoRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This entry controls the addition and deletion of aRtgDnaDestInfo components." ::= { aRtgDnaDestInfo 1 } aRtgDnaDestInfoRowStatusEntry OBJECT-TYPE SYNTAX ARtgDnaDestInfoRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single aRtgDnaDestInfo component." INDEX { aRtgIndex, aRtgDnaIndex, aRtgDnaDestInfoIndex } ::= { aRtgDnaDestInfoRowStatusTable 1 } ARtgDnaDestInfoRowStatusEntry ::= SEQUENCE { aRtgDnaDestInfoRowStatus RowStatus, aRtgDnaDestInfoComponentName DisplayString, aRtgDnaDestInfoStorageType StorageType, aRtgDnaDestInfoIndex Integer32 } aRtgDnaDestInfoRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of aRtgDnaDestInfo components. These components cannot be added nor deleted." ::= { aRtgDnaDestInfoRowStatusEntry 1 } aRtgDnaDestInfoComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { aRtgDnaDestInfoRowStatusEntry 2 } aRtgDnaDestInfoStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the aRtgDnaDestInfo tables." ::= { aRtgDnaDestInfoRowStatusEntry 4 } aRtgDnaDestInfoIndex OBJECT-TYPE SYNTAX Integer32 (0..50) ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the aRtgDnaDestInfo tables." ::= { aRtgDnaDestInfoRowStatusEntry 10 } aRtgDnaDestInfoOperTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgDnaDestInfoOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains the operational attributes for the DestInfo component." ::= { aRtgDnaDestInfo 10 } aRtgDnaDestInfoOperEntry OBJECT-TYPE SYNTAX ARtgDnaDestInfoOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the aRtgDnaDestInfoOperTable." INDEX { aRtgIndex, aRtgDnaIndex, aRtgDnaDestInfoIndex } ::= { aRtgDnaDestInfoOperTable 1 } ARtgDnaDestInfoOperEntry ::= SEQUENCE { aRtgDnaDestInfoType INTEGER, aRtgDnaDestInfoScope INTEGER, aRtgDnaDestInfoStdComponentName RowPointer, aRtgDnaDestInfoReachability INTEGER } aRtgDnaDestInfoType OBJECT-TYPE SYNTAX INTEGER { primary(0), alternate(1), registered(2), default(3) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the type of the address at the destination interface. Provisioned addresses are assigned a type of primary or alternate; ATM routing will try primary routes and then the alternate routes if none of the primary routes succeed. The type registered is used for dynamic addresses registered through ILMI. The type default is used for Soft PVC addresses." ::= { aRtgDnaDestInfoOperEntry 1 } aRtgDnaDestInfoScope OBJECT-TYPE SYNTAX INTEGER (-1..104) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the highest level (meaning the lowest level number) in the hierarchy that the address will be advertised to. A value of -1 indicates that the scope is not applicable since this node has not been configured as a PNNI node." ::= { aRtgDnaDestInfoOperEntry 2 } aRtgDnaDestInfoStdComponentName OBJECT-TYPE SYNTAX RowPointer ACCESS read-only STATUS mandatory DESCRIPTION "This attribute represents a component name of the interface through which the address can be reached." ::= { aRtgDnaDestInfoOperEntry 3 } aRtgDnaDestInfoReachability OBJECT-TYPE SYNTAX INTEGER { internal(0), exterior(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates whether the address is internal or exterior." ::= { aRtgDnaDestInfoOperEntry 4 } -- ARtg Pnni -- This component contains the provisionable and operational -- attributes for a PNNI node. Provisioning the Pnni component under -- the ARtg component indicates that this switch has PNNI routing -- capability. -- The Pnni component must have one and only one ConfiguredNode -- subcomponent. aRtgPnni OBJECT IDENTIFIER ::= { aRtg 3 } aRtgPnniRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of aRtgPnni components." ::= { aRtgPnni 1 } aRtgPnniRowStatusEntry OBJECT-TYPE SYNTAX ARtgPnniRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single aRtgPnni component." INDEX { aRtgIndex, aRtgPnniIndex } ::= { aRtgPnniRowStatusTable 1 } ARtgPnniRowStatusEntry ::= SEQUENCE { aRtgPnniRowStatus RowStatus, aRtgPnniComponentName DisplayString, aRtgPnniStorageType StorageType, aRtgPnniIndex NonReplicated } aRtgPnniRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-write STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of aRtgPnni components. These components can be added and deleted." ::= { aRtgPnniRowStatusEntry 1 } aRtgPnniComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { aRtgPnniRowStatusEntry 2 } aRtgPnniStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the aRtgPnni tables." ::= { aRtgPnniRowStatusEntry 4 } aRtgPnniIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the aRtgPnni tables." ::= { aRtgPnniRowStatusEntry 10 } aRtgPnniProvTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the generic provisionable attributes of a Pnni component." ::= { aRtgPnni 10 } aRtgPnniProvEntry OBJECT-TYPE SYNTAX ARtgPnniProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the aRtgPnniProvTable." INDEX { aRtgIndex, aRtgPnniIndex } ::= { aRtgPnniProvTable 1 } ARtgPnniProvEntry ::= SEQUENCE { aRtgPnniNodeAddressPrefix HexString, aRtgPnniDefaultScope Unsigned32, aRtgPnniDomain AsciiString, aRtgPnniRestrictTransit INTEGER, aRtgPnniMaxReroutesOnCrankback Unsigned32 } aRtgPnniNodeAddressPrefix OBJECT-TYPE SYNTAX HexString (SIZE (0..19)) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the ATM address of this node. It allows the default node address to be overridden. If this attribute is set to the null string, then the default node address prefix is assumed, and computed as follows: the value provisioned for the ModuleData component's nodePrefix attribute, followed by a unique MAC address (6 octets)." ::= { aRtgPnniProvEntry 1 } aRtgPnniDefaultScope OBJECT-TYPE SYNTAX Unsigned32 (0..104) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the default PNNI scope for ATM addresses associated with this node. The PNNI scope determines the level to which the address will be advertised within the PNNI routing domain. A provisioned Addr component may override the default scope in a PnniInfo subcomponent. A value of 0 means that all addresses which do not have provisioned scopes will be advertised globally within the PNNI routing domain. The value specified must be numerically smaller than or equal to that of the lowest level at which this node is configured in the PNNI hierarchy." DEFVAL { 0 } ::= { aRtgPnniProvEntry 2 } aRtgPnniDomain OBJECT-TYPE SYNTAX AsciiString (SIZE (1..32)) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the routing domain name. This attribute should be set identically for all nodes in the same routing domain." DEFVAL { '31'H } -- "1" ::= { aRtgPnniProvEntry 3 } aRtgPnniRestrictTransit OBJECT-TYPE SYNTAX INTEGER { false(0), true(1) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies if the node should restrict tandeming of SVCs. If this attribute is set to true, then other lowest level nodes in the PNNI hierarchy will avoid traversing this node during route computation." DEFVAL { false } ::= { aRtgPnniProvEntry 4 } aRtgPnniMaxReroutesOnCrankback OBJECT-TYPE SYNTAX Unsigned32 (0..20) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the number of alternate routing attempts before a call requiring crank back is rejected." DEFVAL { 1 } ::= { aRtgPnniProvEntry 5 } aRtgPnniPglParmsTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniPglParmsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the provisionable attributes for the peer group leader election timer parameters of a Pnni component." ::= { aRtgPnni 11 } aRtgPnniPglParmsEntry OBJECT-TYPE SYNTAX ARtgPnniPglParmsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the aRtgPnniPglParmsTable." INDEX { aRtgIndex, aRtgPnniIndex } ::= { aRtgPnniPglParmsTable 1 } ARtgPnniPglParmsEntry ::= SEQUENCE { aRtgPnniPglInitTime Unsigned32, aRtgPnniOverrideDelay Unsigned32, aRtgPnniReElectionInterval Unsigned32 } aRtgPnniPglInitTime OBJECT-TYPE SYNTAX Unsigned32 (0..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies how long this node will delay advertising its choice of preferred peer group leader after having initialized operation and reached the full peer state with at least one neighbor in the peer group." DEFVAL { 15 } ::= { aRtgPnniPglParmsEntry 1 } aRtgPnniOverrideDelay OBJECT-TYPE SYNTAX Unsigned32 (1..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies how long a node will wait for itself to be declared the preferred peer group leader by unanimous agreement among its peers." DEFVAL { 30 } ::= { aRtgPnniPglParmsEntry 2 } aRtgPnniReElectionInterval OBJECT-TYPE SYNTAX Unsigned32 (1..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies how long this node will wait after losing connectivity to the current peer group leader before re-starting the process of electing a new peer group leader." DEFVAL { 15 } ::= { aRtgPnniPglParmsEntry 3 } aRtgPnniHlParmsTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniHlParmsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the default provisionable Hello protocol parameters." ::= { aRtgPnni 12 } aRtgPnniHlParmsEntry OBJECT-TYPE SYNTAX ARtgPnniHlParmsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the aRtgPnniHlParmsTable." INDEX { aRtgIndex, aRtgPnniIndex } ::= { aRtgPnniHlParmsTable 1 } ARtgPnniHlParmsEntry ::= SEQUENCE { aRtgPnniHelloHoldDown FixedPoint1, aRtgPnniHelloInterval Unsigned32, aRtgPnniHelloInactivityFactor Unsigned32 } aRtgPnniHelloHoldDown OBJECT-TYPE SYNTAX FixedPoint1 (1..655350) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute is used to limit the rate at which this node sends out Hello packets. Specifically, it specifies the default minimum amount of time between successive Hellos used by routing control channels on this node." DEFVAL { 10 } ::= { aRtgPnniHlParmsEntry 1 } aRtgPnniHelloInterval OBJECT-TYPE SYNTAX Unsigned32 (1..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the default duration of the Hello Timer in seconds for routing control channels on this node. Every helloInterval seconds, this node will send out a Hello packet to the neighbor node, subject to the helloHoldDown timer having expired at least once since the last Hello packet was sent." DEFVAL { 15 } ::= { aRtgPnniHlParmsEntry 2 } aRtgPnniHelloInactivityFactor OBJECT-TYPE SYNTAX Unsigned32 (1..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the default number of Hello intervals allowed to pass without receiving a Hello from the neighbor node, before an attempt is made to re-stage, for routing control channels on this node. The hello inactivity timer is enabled in the oneWayInside, twoWayInside, oneWayOutside, twoWayOutside and commonOutside (see the helloState attribute on the Rcc component for a description of these states). Note that the value for the Hello interval used in the calculation is the one specified in the Hello packet from the neighbor node." DEFVAL { 5 } ::= { aRtgPnniHlParmsEntry 3 } aRtgPnniPtseParmsTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniPtseParmsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the provisionable attributes for the PTSE timer values of a Pnni component." ::= { aRtgPnni 13 } aRtgPnniPtseParmsEntry OBJECT-TYPE SYNTAX ARtgPnniPtseParmsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the aRtgPnniPtseParmsTable." INDEX { aRtgIndex, aRtgPnniIndex } ::= { aRtgPnniPtseParmsTable 1 } ARtgPnniPtseParmsEntry ::= SEQUENCE { aRtgPnniPtseHoldDown FixedPoint1, aRtgPnniPtseRefreshInterval Unsigned32, aRtgPnniPtseLifetimeFactor Unsigned32, aRtgPnniRequestRxmtInterval Unsigned32, aRtgPnniPeerDelayedAckInterval FixedPoint1 } aRtgPnniPtseHoldDown OBJECT-TYPE SYNTAX FixedPoint1 (1..655350) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute is used to limit the rate at which this node sends out PTSE packets. Specifically, it specifies the minimum amount of time in seconds that this node must wait between sending successive PTSE packets." DEFVAL { 10 } ::= { aRtgPnniPtseParmsEntry 1 } aRtgPnniPtseRefreshInterval OBJECT-TYPE SYNTAX Unsigned32 (300..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the duration of the PTSE Timer. Every ptseRefreshInterval seconds, this node will send out a self- originated PTSE packet to the neighbor node, subject to the ptseHoldDown timer having expired at least once since the last PTSE packet was sent." DEFVAL { 1800 } ::= { aRtgPnniPtseParmsEntry 2 } aRtgPnniPtseLifetimeFactor OBJECT-TYPE SYNTAX Unsigned32 (101..1000) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the lifetime multiplier. The result of multiplying the ptseRefreshInterval by this value is used as the initial lifetime that this node places into PTSEs." DEFVAL { 200 } ::= { aRtgPnniPtseParmsEntry 3 } aRtgPnniRequestRxmtInterval OBJECT-TYPE SYNTAX Unsigned32 (1..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the period between retransmissions of unacknowledged Database Summary packets, PTSE Request packets and PTSPs." DEFVAL { 5 } ::= { aRtgPnniPtseParmsEntry 4 } aRtgPnniPeerDelayedAckInterval OBJECT-TYPE SYNTAX FixedPoint1 (1..655350) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the minimum amount of time between transmissions of delayed PTSE acknowledgment packets." DEFVAL { 1 } ::= { aRtgPnniPtseParmsEntry 5 } aRtgPnniThreshParmsTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniThreshParmsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the provisionable attributes for the change thresholds of a ARtg Pnni component." ::= { aRtgPnni 14 } aRtgPnniThreshParmsEntry OBJECT-TYPE SYNTAX ARtgPnniThreshParmsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the aRtgPnniThreshParmsTable." INDEX { aRtgIndex, aRtgPnniIndex } ::= { aRtgPnniThreshParmsTable 1 } ARtgPnniThreshParmsEntry ::= SEQUENCE { aRtgPnniAvcrMt Unsigned32, aRtgPnniAvcrPm Unsigned32 } aRtgPnniAvcrMt OBJECT-TYPE SYNTAX Unsigned32 (1..99) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute when multiplied by the Maximum Cell Rate specifies the minimum threshold used in the algorithms that determine significant change for average cell rate parameters." DEFVAL { 3 } ::= { aRtgPnniThreshParmsEntry 1 } aRtgPnniAvcrPm OBJECT-TYPE SYNTAX Unsigned32 (1..99) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute when multiplied by the current Available Cell Rate specifies the threshold used in the algorithms that determine significant change for AvCR parameters. If the resulting threshold is lower than minimum threshold, minimum threshold will be used. Increasing the value of the attribute increases the range of insignificance and reduces the amount of PTSP flooding due to changes in resource availability." DEFVAL { 50 } ::= { aRtgPnniThreshParmsEntry 2 } aRtgPnniOperTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the generic operational attributes of an ARtg Pnni component." ::= { aRtgPnni 15 } aRtgPnniOperEntry OBJECT-TYPE SYNTAX ARtgPnniOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the aRtgPnniOperTable." INDEX { aRtgIndex, aRtgPnniIndex } ::= { aRtgPnniOperTable 1 } ARtgPnniOperEntry ::= SEQUENCE { aRtgPnniTopologyMemoryExhaustion INTEGER } aRtgPnniTopologyMemoryExhaustion OBJECT-TYPE SYNTAX INTEGER { false(0), true(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates if the topology database is overloaded. A node goes into a database overload state when it fails to store the complete topology database due to insufficient memory in the node. A node in this state performs resynchronization periodically by restarting all its Neighbor Peer Finite State Machines. The node will stay in this state until it synchronizes with all of its neighbors without any overload problems. When this attribute is set an alarm will be issued." ::= { aRtgPnniOperEntry 2 } aRtgPnniStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the statistical operational attributes of a ARtg Pnni component." ::= { aRtgPnni 16 } aRtgPnniStatsEntry OBJECT-TYPE SYNTAX ARtgPnniStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the aRtgPnniStatsTable." INDEX { aRtgIndex, aRtgPnniIndex } ::= { aRtgPnniStatsTable 1 } ARtgPnniStatsEntry ::= SEQUENCE { aRtgPnniRoutingAttempts Counter32, aRtgPnniFailedRoutingAttempts Counter32, aRtgPnniCallsRerouted Counter32 } aRtgPnniRoutingAttempts OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts successful PNNI routing attempts. The counter wraps when it exceeds the maximum value." ::= { aRtgPnniStatsEntry 1 } aRtgPnniFailedRoutingAttempts OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts failed PNNI routing attempts. The counter wraps when it exceeds the maximum value." ::= { aRtgPnniStatsEntry 2 } aRtgPnniCallsRerouted OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts successful PNNI alternate routing attempts. The counter wraps when it exceeds the maximum value." ::= { aRtgPnniStatsEntry 3 } aRtgPnniOptMetricTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniOptMetricEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute is a vector that specifies the optimization metric for each ATM service category. The optimization metric is used during Generic Connection Admission Control (GCAC) route computation. Setting the value to cdv for a particular service category will cause GCAC to optimize for cell delay variation on call setups requiring that service category. Setting the value to maxCtd for a particular service category will cause GCAC to optimize for maximum cell transfer delay on call setups requiring that service category. Setting the value to aw for a particular service category will cause GCAC to optimize for administrative weight on call setups requiring that service category." ::= { aRtgPnni 386 } aRtgPnniOptMetricEntry OBJECT-TYPE SYNTAX ARtgPnniOptMetricEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the aRtgPnniOptMetricTable." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniOptMetricIndex } ::= { aRtgPnniOptMetricTable 1 } ARtgPnniOptMetricEntry ::= SEQUENCE { aRtgPnniOptMetricIndex INTEGER, aRtgPnniOptMetricValue INTEGER } aRtgPnniOptMetricIndex OBJECT-TYPE SYNTAX INTEGER { cbr(1), rtVbr(2), nrtVbr(3), ubr(4) } ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the aRtgPnniOptMetricTable specific index for the aRtgPnniOptMetricTable." ::= { aRtgPnniOptMetricEntry 1 } aRtgPnniOptMetricValue OBJECT-TYPE SYNTAX INTEGER { cdv(0), maxCtd(1), aw(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This variable represents an individual value for the aRtgPnniOptMetricTable." ::= { aRtgPnniOptMetricEntry 2 } -- ARtg Pnni RouteFinder -- This component is used to compute a list of routes to a specified -- destination which satisfy certain traffic and routing requirements. -- -- To display a list of computed routes: -- - set the route computation criteria -- - issue the Run command aRtgPnniRf OBJECT IDENTIFIER ::= { aRtgPnni 2 } aRtgPnniRfRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniRfRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of aRtgPnniRf components." ::= { aRtgPnniRf 1 } aRtgPnniRfRowStatusEntry OBJECT-TYPE SYNTAX ARtgPnniRfRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single aRtgPnniRf component." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniRfIndex } ::= { aRtgPnniRfRowStatusTable 1 } ARtgPnniRfRowStatusEntry ::= SEQUENCE { aRtgPnniRfRowStatus RowStatus, aRtgPnniRfComponentName DisplayString, aRtgPnniRfStorageType StorageType, aRtgPnniRfIndex NonReplicated } aRtgPnniRfRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of aRtgPnniRf components. These components cannot be added nor deleted." ::= { aRtgPnniRfRowStatusEntry 1 } aRtgPnniRfComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { aRtgPnniRfRowStatusEntry 2 } aRtgPnniRfStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the aRtgPnniRf tables." ::= { aRtgPnniRfRowStatusEntry 4 } aRtgPnniRfIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the aRtgPnniRf tables." ::= { aRtgPnniRfRowStatusEntry 10 } aRtgPnniRfCriteriaTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniRfCriteriaEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the attributes specifying the routing criteria for the route computation." ::= { aRtgPnniRf 10 } aRtgPnniRfCriteriaEntry OBJECT-TYPE SYNTAX ARtgPnniRfCriteriaEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the aRtgPnniRfCriteriaTable." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniRfIndex } ::= { aRtgPnniRfCriteriaTable 1 } ARtgPnniRfCriteriaEntry ::= SEQUENCE { aRtgPnniRfDestinationAddress HexString, aRtgPnniRfMaxRoutes Unsigned32, aRtgPnniRfTxTrafficDescType INTEGER, aRtgPnniRfRxTrafficDescType INTEGER, aRtgPnniRfAtmServiceCategory INTEGER, aRtgPnniRfFwdQosClass INTEGER, aRtgPnniRfBwdQosClass INTEGER, aRtgPnniRfBearerClassBbc INTEGER, aRtgPnniRfTransferCapabilityBbc INTEGER, aRtgPnniRfClippingBbc INTEGER, aRtgPnniRfBestEffort INTEGER, aRtgPnniRfOptimizationMetric INTEGER } aRtgPnniRfDestinationAddress OBJECT-TYPE SYNTAX HexString (SIZE (1..20)) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the destination NSAP address to be used for the computation. If this attribute specifies an invalid address then no routes will be found." ::= { aRtgPnniRfCriteriaEntry 1 } aRtgPnniRfMaxRoutes OBJECT-TYPE SYNTAX Unsigned32 (1..15) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies a ceiling on the number of routes to be computed." DEFVAL { 1 } ::= { aRtgPnniRfCriteriaEntry 2 } aRtgPnniRfTxTrafficDescType OBJECT-TYPE SYNTAX INTEGER { n1(1), n2(2), n3(3), n4(4), n5(5), n6(6), n7(7), n8(8) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the type of traffic management which is applied to the transmit direction as defined in the ATM Forum. The txTrafficDescType determines the number and meaning of the parameters in the txTrafficDescParm attribute." DEFVAL { n1 } ::= { aRtgPnniRfCriteriaEntry 3 } aRtgPnniRfRxTrafficDescType OBJECT-TYPE SYNTAX INTEGER { n1(1), n2(2), n3(3), n4(4), n5(5), n6(6), n7(7), n8(8), sameAsTx(15) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the type of traffic management which is applied to the receive direction of this connection as defined in the ATM Forum. The rxTrafficDescType determines the number and meaning of the parameters in the rxTrafficDescParm attribute When sameAsTx is selected, the rxTrafficDescType as well as the rxTrafficDescParm are taken from the transmit values." DEFVAL { sameAsTx } ::= { aRtgPnniRfCriteriaEntry 5 } aRtgPnniRfAtmServiceCategory OBJECT-TYPE SYNTAX INTEGER { unspecifiedBitRate(0), constantBitRate(1), rtVariableBitRate(2), nrtVariableBitRate(3), derivedFromBBC(15) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the ATM service category for both directions of the connection. If this attribute is set to derivedFromBBC, the Broadband Bearer Capability (BBC) and bestEffort attributes are used to determine the atmServiceCategory of this connection. If this attribute is set to other than derivedFromBBC, the value of this attribute is used to override the provisioned BBC IE parameters. In those cases, the BBC attributes are not used. The constantBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. The consistent availability of a fixed quantity of bandwidth is considered appropriate for CBR service. Cells which are delayed beyond the value specified by CellTransfer Delay are assumed to be of significantly reduce value to the application. The rtVariableBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. Sources are expected to transmit at a rate which varies with time. Equivalently, the source can be described as 'bursty'. Cells which are delayed beyond the value specified by CTD are assumed to be of significantly reduced value to the application. VBR real time service may support statistical multiplexing of real time sources. The nrtVariableBitRate service category is intended for non-real time applications which have bursty traffic characteristics and which can be characterized in terms of a PCR, SCR, and MBS. For those cells which are transferred within the traffic contract, the application expects a low cell loss ratio. For all connections, it expects a bound on the mean cell transfer delay. VBR non-real time service may support statistical multiplexing of connections. The unspecifiedBitRate service is intended for non-real time applications; that is, those not requiring tightly constrained delay and delay variation. UBR sources are expected to be bursty. UBR service supports a high degree of statistical multiplexing among sources. UBR service does not specify traffic related service guarantees. No numerical commitments are made with respect to the cell loss ratio experienced by a UBR connection, or as to the cell transfer delay experienced by cells on the connection." DEFVAL { unspecifiedBitRate } ::= { aRtgPnniRfCriteriaEntry 6 } aRtgPnniRfFwdQosClass OBJECT-TYPE SYNTAX INTEGER { n0(0), n1(1), n2(2), n3(3), n4(4) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the quality of service for the forward direction for this connection. Class 1 supports a QOS that will meet Service Class A performance requirements (Circuit emulation, constant bit rate video). Class 2 supports a QOS that will meet Service Class B performance requirements (Variable bit rate audio and video). Class 3 supports a QOS that will meet Service Class C performance requirements (Connection-Oriented Data Transfer). Class 4 supports a QOS that will meet Service Class D performance requirements (Connectionless Data Transfer). Class 0 is the unspecified bit rate QOS class; no objective is specified for the performance parameters." DEFVAL { n0 } ::= { aRtgPnniRfCriteriaEntry 10 } aRtgPnniRfBwdQosClass OBJECT-TYPE SYNTAX INTEGER { n0(0), n1(1), n2(2), n3(3), n4(4), sameAsFwd(15) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the quality of service for the backward direction for this connection. Class 1 supports a QOS that will meet Service Class A performance requirements (Circuit emulation, constant bit rate video). Class 2 supports a QOS that will meet Service Class B performance requirements (Variable bit rate audio and video). Class 3 supports a QOS that will meet Service Class C performance requirements (Connection-Oriented Data Transfer). Class 4 supports a QOS that will meet Service Class D performance requirements (Connectionless Data Transfer). Class 0 is the unspecified bit rate QOS class; no objective is specified for the performance parameters. The sameAsFwd selection sets the backward quality of service to be the same as the forward quality of service." DEFVAL { sameAsFwd } ::= { aRtgPnniRfCriteriaEntry 11 } aRtgPnniRfBearerClassBbc OBJECT-TYPE SYNTAX INTEGER { a(1), c(3), x(16), derivedFromServiceCategory(31) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the bearer capability. It is one of the Broadband Bearer Capability (BBC) attributes. The purpose of the BBC information element is to indicate a requested broadband connection-oriented bearer service to be provided by the network. The value derivedFromServiceCategory specifies that the actual value which is used for this connection is derived from the value of the atmServiceCategory. Either, this attribute must be set to derivedFromServiceCategory, or the atmServiceCategory attribute must be set to derivedFromBBC, but not both. Class a service is a connection-oriented, constant bit rate ATM transport service. Class a service has end to end timing requirements and may require stringent cell loss, cell delay and cell delay variation performance.When a is set, the user is requesting more than an ATM only service. The network may look at the AAL to provide interworking based upon its contents. Class c service is a connection-oriented, variable bit rate ATM transport service. Class c service has no end-to-end timing requirements. When c is set, the user is requesting more than an ATM only service. The network interworking function may look at the AAL and provide service based on it. Class x service is a connection-oriented ATM transport service where the AAL, trafficType (vbr or cbr) and timing requirements are user defined (that is, transparent to the network).When x is set the user is requesting an ATM only service from the network. In this case, the network shall not process any higher layer protocol." DEFVAL { derivedFromServiceCategory } ::= { aRtgPnniRfCriteriaEntry 12 } aRtgPnniRfTransferCapabilityBbc OBJECT-TYPE SYNTAX INTEGER { n0(0), n1(1), n2(2), n5(5), n8(8), n9(9), n10(10), notApplicable(30), derivedFromServiceCategory(31) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the transfer capability for this connection. Uni 3.0/3.1 traffic type and end-to-end timing parameters are mapped into this parameter as follows: 0 : NoIndication, NoIndication 1 : NoIndication, yes 2 : NoIndication, no 5 : CBR, yes 8 : VBR, NoIndication 9 : VBR, yes 10: VBR, no NotApplicable specifies that the user does not want to specify the transfer capability. The CBR traffic type refers to traffic offered on services such as a constant bit rate video service or a circuit emulation. The VBR traffic type refers to traffic offered on services such as packetized audio and video, or data. The value NoIndication for traffic type is used if the user has not set the traffic type; this is also the case for end-to-end timing. The value yes for end-to-end timing indicates that end-to-end timing is required. The value no for end-to-end timing indicates that end-to-end timing is not required. The value derivedFromServiceCategory specifies that the actual value which is used for this connection is derived from the value of the atmServiceCategory. Either, this attribute must be set to derivedFromServiceCategory, or the atmServiceCategory attribute must be set to derivedFromBBC, but not both." DEFVAL { derivedFromServiceCategory } ::= { aRtgPnniRfCriteriaEntry 13 } aRtgPnniRfClippingBbc OBJECT-TYPE SYNTAX INTEGER { no(0), yes(1) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the value for the clipping susceptibility parameter in the BBC IE. This attribute is only used for SPVC connections. It is one of the Broadband Bearer Capability attributes. Clipping is an impairment in which the first fraction of a second of information to be transferred is lost. It occurs after a call is answered and before an associated connection is switched through." DEFVAL { no } ::= { aRtgPnniRfCriteriaEntry 14 } aRtgPnniRfBestEffort OBJECT-TYPE SYNTAX INTEGER { indicated(0), notIndicated(1), derivedFromServiceCategory(15) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the value of the best effort parameter in the ATM Traffic Descriptor IE. It is one of the Broadband Bearer Capability attributes. The value indicated implies that the quality of service for this connection is not guaranteed. The value notIndicated implies that the quality of service for this connection is guaranteed. The value derivedFromServiceCategory specifies that the actual value which is used for this connection is derived from the value of the atmServiceCategory. Either, this attribute must be set to derivedFromServiceCategory, or the atmServiceCategory attribute must be set to derivedFromBBC, but not both. DESCRIPTION" DEFVAL { derivedFromServiceCategory } ::= { aRtgPnniRfCriteriaEntry 15 } aRtgPnniRfOptimizationMetric OBJECT-TYPE SYNTAX INTEGER { cdv(0), maxCtd(1), aw(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the optimization metric to be used in the route computation; one of cell delay variation (cdv), maximum cell transfer delay (maxCtd), or administrative weight (aw)." DEFVAL { aw } ::= { aRtgPnniRfCriteriaEntry 16 } aRtgPnniRfRxTdpTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniRfRxTdpEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute is a vector of four traffic parameters whose meanings are defined by the rxTrafficDescType attribute. The values of peak cell rate (PCR) and sustained cell rate (SCR) are expressed in cell/s. Maximum burst size (MBS) is expressed in cells. The value of CDVT is expressed in microseconds. The values of PCR, SCR, MBS and CDVT are used for usage parameter control (UPC). When rxTrafficDescType is 1 or 2, all of the parameters must be set to zero (unused). When rxTrafficDescType is 3, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic. Parameter 1 must be non-zero. Parameters 2 and 3 must be set to zero (unused). When rxTrafficDescType is 4, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the PCR for CLP equal to 0 traffic with cell discard. Parameters 1 and 2 must be non-zero. Parameter 3 must be set to zero (unused). Parameter 1 must be greater than or equal to parameter 2. When rxTrafficDescType is 5, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the PCR for CLP equal to 0 traffic with cell tagging. Parameters 1 and 2 must be non-zero. Parameter 3 must be set to zero (unused). Parameter 1 must be greater than or equal to parameter 2. When rxTrafficDescType is a 6, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 and 1 traffic; parameter 3 represents the MBS for CLP equal to 0 and 1 traffic. Parameters 1, 2 and 3 must be non- zero. Parameter 1 must be greater than or equal to Parameter 2. When rxTrafficDescType is 7, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 traffic with cell discard; parameter 3 represents the MBS for CLP equal to 0 traffic. Parameters 1, 2 and 3 must be non- zero. Parameter 1 must be greater than or equal to parameter 2. When rxTrafficDescType is 8, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 traffic with cell tagging; parameter 3 represents the MBS for CLP equal to 0 traffic. Parameter 1, 2 and 3 must be non- zero. Parameter 1 must be greater than or equal to parameter 2. When rxTrafficDescType is any value from 3 through 8, parameter 4 represents the CDVT. If this value is zero, the CDVT is taken from the ConnectionAdministrator defaults for the particular atmServiceCategory of this connection. When rxTrafficDescriptorType is 3 through 8, there are certain extreme combinations of rxTrafficDescParm which are outside the capabilities of the UPC hardware. To calculate the limits, use the following formulae: I1 = 1 000 000 000 / PCR L1 = CDVT * 1000 I2 = 1 000 000 000 / SCR L2 = CDVT + (MBS - 1) * (I2 - I1) I1 and I2 must be less than or equal to 335 523 840. I1 + L1 must be less than or equal to 1 342 156 800. I2 + L2 must be less than or equal to 1 342 156 800. Note that I2 and L2 only apply when the rxTrafficDescriptorType is 6 through 8. If the values of I1, L1, I2 or L2 are closer to the limits described above, a further restriction applies. Specifically, if either: I1 > 41 940 480 or I2 > 41 940 480 or I1 + L1 > 167 769 600 or I2 + L2 > 167 769 600 then both I1 and I2 must be greater than 20 480. Parameter 5 of the rxTrafficDescParm is always unused. If the rxTrafficDescType is sameAsTx, the values in this attribute will be taken from the txTrafficDescParm." ::= { aRtgPnniRf 388 } aRtgPnniRfRxTdpEntry OBJECT-TYPE SYNTAX ARtgPnniRfRxTdpEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the aRtgPnniRfRxTdpTable." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniRfIndex, aRtgPnniRfRxTdpIndex } ::= { aRtgPnniRfRxTdpTable 1 } ARtgPnniRfRxTdpEntry ::= SEQUENCE { aRtgPnniRfRxTdpIndex Integer32, aRtgPnniRfRxTdpValue Unsigned32 } aRtgPnniRfRxTdpIndex OBJECT-TYPE SYNTAX Integer32 (1..5) ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the aRtgPnniRfRxTdpTable specific index for the aRtgPnniRfRxTdpTable." ::= { aRtgPnniRfRxTdpEntry 1 } aRtgPnniRfRxTdpValue OBJECT-TYPE SYNTAX Unsigned32 (0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "This variable represents an individual value for the aRtgPnniRfRxTdpTable." ::= { aRtgPnniRfRxTdpEntry 2 } aRtgPnniRfTxTdpTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniRfTxTdpEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute is a vector of five traffic parameters whose meanings are defined by the txTrafficDescType attribute. The values of peak cell rate (PCR), sustained cell rate (SCR) and requested shaping rate are expressed in cell/s. Maximum burst size (MBS) is expressed in cells. CDVT is expressed in microseconds. The values of PCR, SCR, MBS and CDVT are used for connection admission control (CAC). The value of CDVT is only used for connections where the atmServiceCategory is constantBitRate. For all other values of atmServiceCategory, CDVT is ignored. The values of PCR, SCR and requested shaping rate are used to determine the actual shaping rate where traffic shaping is enabled. When txTrafficDescType is 1 or 2, all of the parameters must be set to zero. When txTrafficDescType is 3, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameter 1 must be non-zero. Parameters 2 and 3 must be zero. When txTrafficDescType is 4, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic with cell discard; parameter 2 represents the PCR for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameter 1 must be greater than or equal to parameter 2. Parameters 1 and 2 must be non-zero. Parameter 3 must be zero. When txTrafficDescType is 5, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic with cell tagging; parameter 2 represents the PCR for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameter 1 must be greater than or equal to parameter 2. Parameters 1 and 2 must be non-zero. Parameter 3 must be zero. When txTrafficDescType is 6, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 and 1 traffic; parameter 3 represents the MBS for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2 and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5, must either be zero (unused) or greater than or equal to parameter 2. When txTrafficDescType is 7, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 with cell discard; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2 and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5, must either be zero (unused) or greater than or equal to parameter 2. When txTrafficDescType is 8, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 traffic with cell tagging; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2 and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5, must either be zero (unused) or greater than or equal to parameter 2. Whenever it is valid for PCR to be specified, parameter 5 may also be used to specify a requested shaping rate. A non-zero value in parameter 5 overrides the value in parameter 1 and is used as the peak cell rate in calculations of CAC and shaping rate. For txTrafficDescType 3, 4 and 5, the transmit traffic will be shaped at the next rate less than the PCR. For txTrafficDescType 6, 7 and 8, the transmit traffic will be shaped at the highest available rate which is between PCR and SCR. However, if there is no available shaping rate between PCR and SCR, traffic will be shaped at the next rate above the PCR." ::= { aRtgPnniRf 389 } aRtgPnniRfTxTdpEntry OBJECT-TYPE SYNTAX ARtgPnniRfTxTdpEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the aRtgPnniRfTxTdpTable." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniRfIndex, aRtgPnniRfTxTdpIndex } ::= { aRtgPnniRfTxTdpTable 1 } ARtgPnniRfTxTdpEntry ::= SEQUENCE { aRtgPnniRfTxTdpIndex Integer32, aRtgPnniRfTxTdpValue Unsigned32 } aRtgPnniRfTxTdpIndex OBJECT-TYPE SYNTAX Integer32 (1..5) ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the aRtgPnniRfTxTdpTable specific index for the aRtgPnniRfTxTdpTable." ::= { aRtgPnniRfTxTdpEntry 1 } aRtgPnniRfTxTdpValue OBJECT-TYPE SYNTAX Unsigned32 (0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "This variable represents an individual value for the aRtgPnniRfTxTdpTable." ::= { aRtgPnniRfTxTdpEntry 2 } aRtgPnniRfFqpTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniRfFqpEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute is a vector of three elements that specify the quality of service parameters for the forward direction for this connection. This attribute is used for SPVC connections. The cdv element specifies the acceptable peak-to-peak Cell Delay Variation (CDV) of real-time connections (CBR, and rt-VBR). It is signalled through the extended QoS information element. The ctd specifies the acceptable maximum Cell Transfer Delay (maxCtd) of real-time connections (CBR, and rt-VBR). It is signalled through the end to end transit delay information element. The clr specifies the acceptable Cell Loss Ratio (CLR) of CBR, rt- VBR, and nrt-VBR connections. It is signalled through the extended QoS information element." ::= { aRtgPnniRf 390 } aRtgPnniRfFqpEntry OBJECT-TYPE SYNTAX ARtgPnniRfFqpEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the aRtgPnniRfFqpTable." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniRfIndex, aRtgPnniRfFqpIndex } ::= { aRtgPnniRfFqpTable 1 } ARtgPnniRfFqpEntry ::= SEQUENCE { aRtgPnniRfFqpIndex INTEGER, aRtgPnniRfFqpValue Unsigned32 } aRtgPnniRfFqpIndex OBJECT-TYPE SYNTAX INTEGER { cdv(0), ctd(1), clr(2) } ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the aRtgPnniRfFqpTable specific index for the aRtgPnniRfFqpTable." ::= { aRtgPnniRfFqpEntry 1 } aRtgPnniRfFqpValue OBJECT-TYPE SYNTAX Unsigned32 (0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "This variable represents an individual value for the aRtgPnniRfFqpTable." ::= { aRtgPnniRfFqpEntry 2 } aRtgPnniRfBqpTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniRfBqpEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute is a vector of three elements that specify the quality of service parameters for the backward direction for this connection. This attribute is used for SPVC connections. The cdv element specifies the acceptable peak-to-peak Cell Delay Variation (CDV) of real-time connections (CBR, and rt-VBR). It is signalled through the extended QoS information element. The ctd specifies the acceptable maximum Cell Transfer Delay (maxCtd) of real-time connections (CBR, and rt-VBR). It is signalled through the end to end transit delay information element. The clr specifies the acceptable Cell Loss Ratio (CLR) of CBR, rt- VBR, and nrt-VBR connections. It is signalled through the extended QoS information element." ::= { aRtgPnniRf 393 } aRtgPnniRfBqpEntry OBJECT-TYPE SYNTAX ARtgPnniRfBqpEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the aRtgPnniRfBqpTable." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniRfIndex, aRtgPnniRfBqpIndex } ::= { aRtgPnniRfBqpTable 1 } ARtgPnniRfBqpEntry ::= SEQUENCE { aRtgPnniRfBqpIndex INTEGER, aRtgPnniRfBqpValue Unsigned32 } aRtgPnniRfBqpIndex OBJECT-TYPE SYNTAX INTEGER { cdv(0), ctd(1), clr(2) } ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the aRtgPnniRfBqpTable specific index for the aRtgPnniRfBqpTable." ::= { aRtgPnniRfBqpEntry 1 } aRtgPnniRfBqpValue OBJECT-TYPE SYNTAX Unsigned32 (0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "This variable represents an individual value for the aRtgPnniRfBqpTable." ::= { aRtgPnniRfBqpEntry 2 } -- ARtg Pnni ConfiguredNode/ -- This component represents the participation of this node at one level -- in the PNNI hierarchy. aRtgPnniCfgNode OBJECT IDENTIFIER ::= { aRtgPnni 3 } aRtgPnniCfgNodeRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniCfgNodeRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of aRtgPnniCfgNode components." ::= { aRtgPnniCfgNode 1 } aRtgPnniCfgNodeRowStatusEntry OBJECT-TYPE SYNTAX ARtgPnniCfgNodeRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single aRtgPnniCfgNode component." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniCfgNodeIndex } ::= { aRtgPnniCfgNodeRowStatusTable 1 } ARtgPnniCfgNodeRowStatusEntry ::= SEQUENCE { aRtgPnniCfgNodeRowStatus RowStatus, aRtgPnniCfgNodeComponentName DisplayString, aRtgPnniCfgNodeStorageType StorageType, aRtgPnniCfgNodeIndex Integer32 } aRtgPnniCfgNodeRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-write STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of aRtgPnniCfgNode components. These components can be added and deleted." ::= { aRtgPnniCfgNodeRowStatusEntry 1 } aRtgPnniCfgNodeComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { aRtgPnniCfgNodeRowStatusEntry 2 } aRtgPnniCfgNodeStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the aRtgPnniCfgNode tables." ::= { aRtgPnniCfgNodeRowStatusEntry 4 } aRtgPnniCfgNodeIndex OBJECT-TYPE SYNTAX Integer32 (0..104) ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the aRtgPnniCfgNode tables." ::= { aRtgPnniCfgNodeRowStatusEntry 10 } aRtgPnniCfgNodeProvTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniCfgNodeProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the provisionable attributes of a ConfiguredNode component." ::= { aRtgPnniCfgNode 10 } aRtgPnniCfgNodeProvEntry OBJECT-TYPE SYNTAX ARtgPnniCfgNodeProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the aRtgPnniCfgNodeProvTable." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniCfgNodeIndex } ::= { aRtgPnniCfgNodeProvTable 1 } ARtgPnniCfgNodeProvEntry ::= SEQUENCE { aRtgPnniCfgNodeNodeId HexString, aRtgPnniCfgNodePeerGroupId HexString } aRtgPnniCfgNodeNodeId OBJECT-TYPE SYNTAX HexString (SIZE (0..22)) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the node id of the configured node. If this attribute is set to null, then the node id is computed as follows: If this is the lowest configured node, then the node id is computed as the level (one octet), followed by the integer value 160 (one octet), followed by the node address (20 octets). If this is not the lowest configured node, then the node id is computed as the level (one octet), followed by the 14 octet peer group id of the child peer group which the LGN represents, followed by the ESI specified in the node address (6 octets), followed by the integer value 0 (one octet)." ::= { aRtgPnniCfgNodeProvEntry 2 } aRtgPnniCfgNodePeerGroupId OBJECT-TYPE SYNTAX HexString (SIZE (0..14)) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute allows the peer group id of the Logical Group Node (LGN) to be set. The peer group id is specified by 28 hex digits where the first octet represents the level of the node and the remaining 13 octets form the End System Address. If this attribute is set to the null string then the peer group id is computed as follows: The peer group id for a lowest level node is computed to be the node's level (one octet), followed by the first bits of the node's address, followed by zero or more padding 0 bits. The peer group id for an LGN is computed to be the LGN's level (one octet), followed by the first bits of the id of the peer group which this LGN represents." ::= { aRtgPnniCfgNodeProvEntry 3 } aRtgPnniCfgNodeOperTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniCfgNodeOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the generic operational attributes of a ConfiguredNode component." ::= { aRtgPnniCfgNode 11 } aRtgPnniCfgNodeOperEntry OBJECT-TYPE SYNTAX ARtgPnniCfgNodeOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the aRtgPnniCfgNodeOperTable." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniCfgNodeIndex } ::= { aRtgPnniCfgNodeOperTable 1 } ARtgPnniCfgNodeOperEntry ::= SEQUENCE { aRtgPnniCfgNodeNodeAddress HexString, aRtgPnniCfgNodeOpNodeId HexString, aRtgPnniCfgNodeOpPeerGroupId HexString, aRtgPnniCfgNodeNumNeighbors Unsigned32, aRtgPnniCfgNodeNumRccs Unsigned32, aRtgPnniCfgNodeCurrentLeadershipPriority Unsigned32, aRtgPnniCfgNodePglElectionState INTEGER } aRtgPnniCfgNodeNodeAddress OBJECT-TYPE SYNTAX HexString (SIZE (20)) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the address of the node at this level. At the lowest level, the nodeAddress is determined by the value of the nodeAddressPrefix attribute for the ARtg Pnni component followed by the level of this CfgNode. For LGNs, the nodeAddress is the same as the nodeAddress of the node at the lowest level, with the selector field set to the level of the peer group containing the LGN." ::= { aRtgPnniCfgNodeOperEntry 1 } aRtgPnniCfgNodeOpNodeId OBJECT-TYPE SYNTAX HexString (SIZE (22)) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the node id of the node at this level. The default node id is computed as follows: If this is the lowest level node, then the default node id is computed as the level (one octet), followed by the integer value 160 (one octet), followed by the node address (20 octets). If this is not the lowest level node, then the default node id is computed as the level (one octet), followed by the 14 octet peer group id of the child peer group which the LGN represents, followed by the ESI specified in the node address (6 octets), followed by the integer value 0 (one octet)." ::= { aRtgPnniCfgNodeOperEntry 2 } aRtgPnniCfgNodeOpPeerGroupId OBJECT-TYPE SYNTAX HexString (SIZE (14)) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the peer group id of the node at this level. The value is determined by the provisioned peerGroupId attribute." ::= { aRtgPnniCfgNodeOperEntry 3 } aRtgPnniCfgNodeNumNeighbors OBJECT-TYPE SYNTAX Unsigned32 (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the number of PNNI nodes which are neighbors of this node at this level." ::= { aRtgPnniCfgNodeOperEntry 4 } aRtgPnniCfgNodeNumRccs OBJECT-TYPE SYNTAX Unsigned32 (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the number of Routing Control Channels to this node's neighbors at this level." ::= { aRtgPnniCfgNodeOperEntry 5 } aRtgPnniCfgNodeCurrentLeadershipPriority OBJECT-TYPE SYNTAX Unsigned32 (0..205) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the leadership priority of the node that this node believes should be the peer group leader at this point in time." ::= { aRtgPnniCfgNodeOperEntry 6 } aRtgPnniCfgNodePglElectionState OBJECT-TYPE SYNTAX INTEGER { starting(0), awaiting(1), awaitingFull(2), initialDelay(3), calculating(4), operNotPgl(5), operPgl(6), awaitUnanimity(7), hungElection(8), awaitReElection(9) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the current state of the peer group leader election process. The following are the possible values for this attribute: starting: the initial state of the state machine. awaiting: the node has started the Hello Finite State Machine on at least one link, and no peer has been found yet. awaitingFull: no database synchronization process has been completed yet but at least one neighboring peer has been found. initialDelay: Database synchronization has been completed with at least one neighboring peer. The node must wait pglInitTime second before it can select and advertise its preferred Peer Group Leader (PGL). calculating: the node is in the process of calculating what its new choice for preferred PGL will be. operNotPgl: a non PGL node is in the process of determining which node has the highest priority to be PGL by examining PTSEs sent by other nodes. operPgl: a PGL node is in the process of determining if another node has a higher priority than itself by examining PTSEs sent by other nodes. awaitUnanimity: the node has chosen itself as PGL. If the node has been elected unanimously, it generates a Unanimity event. It waits for unanimity or expiration of the overrideDelay timer before declaring itself peer group leader. hungElection: the node has chosen itself as PGL with less than 2/3 of the other nodes advertising it as their preferred PGL. In this case either this node should change its choice of preferred PGL, or the other nodes are going to accept it as PGL. awaitReElection: the node has lost connectivity to the current PGL. The connectivity must be reestablished before the reElectionInterval timer fires, otherwise the election is redone." ::= { aRtgPnniCfgNodeOperEntry 7 } -- ARtg Pnni CfgNode/ SummaryAddress/
, -- , -- A summary address is an abbreviation of a set of addresses, -- represented by an address prefix that all of the summarized -- addresses have in common. -- A suppressed summary address is used to suppress the -- advertisement of addresses which match this prefix, regardless of -- scope. -- -- The prefixLength specifies the number of prefix bits of the address -- and reachability specifies whether the address is to summarize -- internal or exterior addresses. -- -- An internal address is an address of a destination that is directly -- attached to the logical node. An exterior address is an address of a -- destination that is located outside of the PNNI routing domain but -- can be reached through a port attached to the logical node. aRtgPnniCfgNodeSAddr OBJECT IDENTIFIER ::= { aRtgPnniCfgNode 2 } aRtgPnniCfgNodeSAddrRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniCfgNodeSAddrRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of aRtgPnniCfgNodeSAddr components." ::= { aRtgPnniCfgNodeSAddr 1 } aRtgPnniCfgNodeSAddrRowStatusEntry OBJECT-TYPE SYNTAX ARtgPnniCfgNodeSAddrRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single aRtgPnniCfgNodeSAddr component." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniCfgNodeIndex, aRtgPnniCfgNodeSAddrAddressIndex, aRtgPnniCfgNodeSAddrPrefixLengthIndex, aRtgPnniCfgNodeSAddrReachabilityIndex } ::= { aRtgPnniCfgNodeSAddrRowStatusTable 1 } ARtgPnniCfgNodeSAddrRowStatusEntry ::= SEQUENCE { aRtgPnniCfgNodeSAddrRowStatus RowStatus, aRtgPnniCfgNodeSAddrComponentName DisplayString, aRtgPnniCfgNodeSAddrStorageType StorageType, aRtgPnniCfgNodeSAddrAddressIndex HexString, aRtgPnniCfgNodeSAddrPrefixLengthIndex Integer32, aRtgPnniCfgNodeSAddrReachabilityIndex INTEGER } aRtgPnniCfgNodeSAddrRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-write STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of aRtgPnniCfgNodeSAddr components. These components can be added and deleted." ::= { aRtgPnniCfgNodeSAddrRowStatusEntry 1 } aRtgPnniCfgNodeSAddrComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { aRtgPnniCfgNodeSAddrRowStatusEntry 2 } aRtgPnniCfgNodeSAddrStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the aRtgPnniCfgNodeSAddr tables." ::= { aRtgPnniCfgNodeSAddrRowStatusEntry 4 } aRtgPnniCfgNodeSAddrAddressIndex OBJECT-TYPE SYNTAX HexString (SIZE (19)) ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents an index for the aRtgPnniCfgNodeSAddr tables." ::= { aRtgPnniCfgNodeSAddrRowStatusEntry 10 } aRtgPnniCfgNodeSAddrPrefixLengthIndex OBJECT-TYPE SYNTAX Integer32 (1..152) ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents an index for the aRtgPnniCfgNodeSAddr tables." ::= { aRtgPnniCfgNodeSAddrRowStatusEntry 11 } aRtgPnniCfgNodeSAddrReachabilityIndex OBJECT-TYPE SYNTAX INTEGER { internal(0), exterior(1) } ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents an index for the aRtgPnniCfgNodeSAddr tables." ::= { aRtgPnniCfgNodeSAddrRowStatusEntry 12 } aRtgPnniCfgNodeSAddrProvTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniCfgNodeSAddrProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the provisionable attributes of a SummaryAddress component. A summary address is an abbreviation of a set of addresses, represented by an address prefix that all of the summarized addresses have in common. A suppressed summary address is used to suppress the advertisement of addresses which match this prefix, regardless of scope." ::= { aRtgPnniCfgNodeSAddr 10 } aRtgPnniCfgNodeSAddrProvEntry OBJECT-TYPE SYNTAX ARtgPnniCfgNodeSAddrProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the aRtgPnniCfgNodeSAddrProvTable." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniCfgNodeIndex, aRtgPnniCfgNodeSAddrAddressIndex, aRtgPnniCfgNodeSAddrPrefixLengthIndex, aRtgPnniCfgNodeSAddrReachabilityIndex } ::= { aRtgPnniCfgNodeSAddrProvTable 1 } ARtgPnniCfgNodeSAddrProvEntry ::= SEQUENCE { aRtgPnniCfgNodeSAddrSuppress INTEGER } aRtgPnniCfgNodeSAddrSuppress OBJECT-TYPE SYNTAX INTEGER { false(0), true(1) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies whether or not the address should be suppressed. If this attribute is set to true, then all addresses matching that prefix will not be advertised above this level." DEFVAL { false } ::= { aRtgPnniCfgNodeSAddrProvEntry 2 } aRtgPnniCfgNodeSAddrOperTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniCfgNodeSAddrOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the operational attributes of a SummaryAddress component." ::= { aRtgPnniCfgNodeSAddr 11 } aRtgPnniCfgNodeSAddrOperEntry OBJECT-TYPE SYNTAX ARtgPnniCfgNodeSAddrOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the aRtgPnniCfgNodeSAddrOperTable." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniCfgNodeIndex, aRtgPnniCfgNodeSAddrAddressIndex, aRtgPnniCfgNodeSAddrPrefixLengthIndex, aRtgPnniCfgNodeSAddrReachabilityIndex } ::= { aRtgPnniCfgNodeSAddrOperTable 1 } ARtgPnniCfgNodeSAddrOperEntry ::= SEQUENCE { aRtgPnniCfgNodeSAddrState INTEGER, aRtgPnniCfgNodeSAddrScope INTEGER } aRtgPnniCfgNodeSAddrState OBJECT-TYPE SYNTAX INTEGER { advertising(0), suppressing(1), inactive(2) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the state of the address: one of advertising, suppressing or inactive. inactive: the summary address has been configured but is not suppressing or summarizing any ATM addresses. suppressing: the summary address has suppressed at least one ATM address on the node. advertising: the summary address is summarizing at least one ATM address on the node." ::= { aRtgPnniCfgNodeSAddrOperEntry 1 } aRtgPnniCfgNodeSAddrScope OBJECT-TYPE SYNTAX INTEGER (-1..104) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the scope of the summary address. The scope corresponds to the scope of the underlying summarized address with the highest advertised scope. A value of -1 means the scope is unknown." ::= { aRtgPnniCfgNodeSAddrOperEntry 2 } -- -- *** THIS SUBTREE CURRENTLY NOT IMPLEMENTED *** -- -- ARtg Pnni CfgNode/n Neighbor/ -- This component represents the operational attributes for a neighbor -- node at this level. aRtgPnniCfgNodeNbr OBJECT IDENTIFIER ::= { aRtgPnniCfgNode 3 } aRtgPnniCfgNodeNbrRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniCfgNodeNbrRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This entry controls the addition and deletion of aRtgPnniCfgNodeNbr components." ::= { aRtgPnniCfgNodeNbr 1 } aRtgPnniCfgNodeNbrRowStatusEntry OBJECT-TYPE SYNTAX ARtgPnniCfgNodeNbrRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single aRtgPnniCfgNodeNbr component." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniCfgNodeIndex, aRtgPnniCfgNodeNbrIndex } ::= { aRtgPnniCfgNodeNbrRowStatusTable 1 } ARtgPnniCfgNodeNbrRowStatusEntry ::= SEQUENCE { aRtgPnniCfgNodeNbrRowStatus RowStatus, aRtgPnniCfgNodeNbrComponentName DisplayString, aRtgPnniCfgNodeNbrStorageType StorageType, aRtgPnniCfgNodeNbrIndex HexString } aRtgPnniCfgNodeNbrRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of aRtgPnniCfgNodeNbr components. These components cannot be added nor deleted." ::= { aRtgPnniCfgNodeNbrRowStatusEntry 1 } aRtgPnniCfgNodeNbrComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { aRtgPnniCfgNodeNbrRowStatusEntry 2 } aRtgPnniCfgNodeNbrStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the aRtgPnniCfgNodeNbr tables." ::= { aRtgPnniCfgNodeNbrRowStatusEntry 4 } aRtgPnniCfgNodeNbrIndex OBJECT-TYPE SYNTAX HexString (SIZE (22)) ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the aRtgPnniCfgNodeNbr tables." ::= { aRtgPnniCfgNodeNbrRowStatusEntry 10 } aRtgPnniCfgNodeNbrOperTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniCfgNodeNbrOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains the operational attributes of a Neighbor component." ::= { aRtgPnniCfgNodeNbr 10 } aRtgPnniCfgNodeNbrOperEntry OBJECT-TYPE SYNTAX ARtgPnniCfgNodeNbrOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the aRtgPnniCfgNodeNbrOperTable." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniCfgNodeIndex, aRtgPnniCfgNodeNbrIndex } ::= { aRtgPnniCfgNodeNbrOperTable 1 } ARtgPnniCfgNodeNbrOperEntry ::= SEQUENCE { aRtgPnniCfgNodeNbrPeerState INTEGER } aRtgPnniCfgNodeNbrPeerState OBJECT-TYPE SYNTAX INTEGER { npDown(0), negotiating(1), exchanging(2), loading(3), full(4) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the state of the routing database exchange with the peer node. npDown: there are no active links (i.e. in the twoWayInside Hello state) to the neighboring peer. negotiating: the first step in creating an adjacency between the two neighboring peers; this step determines which node is the master, and what the initial DS sequence number will be. exchanging: the node describes its topology database by sending Database Summary packets to the neighboring peer. loading: a full sequence of Database Summary packets has been exchanged with the neighboring peer, and the required PTSEs are requested and at least one has not yet been received. full: All PTSEs known to be available have been received from the neighboring peer. At this point the all ports leading to the neighbor node will be flooded in PTSEs within the peer group." ::= { aRtgPnniCfgNodeNbrOperEntry 2 } aRtgPnniCfgNodeNbrStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniCfgNodeNbrStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains the statistical operational attributes of a Neighbor component." ::= { aRtgPnniCfgNodeNbr 11 } aRtgPnniCfgNodeNbrStatsEntry OBJECT-TYPE SYNTAX ARtgPnniCfgNodeNbrStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the aRtgPnniCfgNodeNbrStatsTable." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniCfgNodeIndex, aRtgPnniCfgNodeNbrIndex } ::= { aRtgPnniCfgNodeNbrStatsTable 1 } ARtgPnniCfgNodeNbrStatsEntry ::= SEQUENCE { aRtgPnniCfgNodeNbrPtspRx Counter32, aRtgPnniCfgNodeNbrPtspTx Counter32, aRtgPnniCfgNodeNbrPtseRx Counter32, aRtgPnniCfgNodeNbrPtseTx Counter32, aRtgPnniCfgNodeNbrPtseReqRx Counter32, aRtgPnniCfgNodeNbrPtseReqTx Counter32, aRtgPnniCfgNodeNbrPtseAcksRx Counter32, aRtgPnniCfgNodeNbrPtseAcksTx Counter32, aRtgPnniCfgNodeNbrDbSummariesRx Counter32, aRtgPnniCfgNodeNbrDbSummariesTx Counter32, aRtgPnniCfgNodeNbrBadPtspRx Counter32, aRtgPnniCfgNodeNbrBadPtseRx Counter32, aRtgPnniCfgNodeNbrBadPtseReqRx Counter32, aRtgPnniCfgNodeNbrBadPtseAckRx Counter32, aRtgPnniCfgNodeNbrBadDbSummariesRx Counter32 } aRtgPnniCfgNodeNbrPtspRx OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the PNNI Topology State Packets received from the neighbor node. The counter wraps when it exceeds the maximum value." ::= { aRtgPnniCfgNodeNbrStatsEntry 1 } aRtgPnniCfgNodeNbrPtspTx OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the total number of PTSPs send to the neighbor node.The counter wraps when it exceeds the maximum value." ::= { aRtgPnniCfgNodeNbrStatsEntry 2 } aRtgPnniCfgNodeNbrPtseRx OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the total number of PTSEs received from the neighbor node. The counter wraps when it exceeds the maximum value." ::= { aRtgPnniCfgNodeNbrStatsEntry 3 } aRtgPnniCfgNodeNbrPtseTx OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the total number of PTSEs sent to the neighbor node. The counter wraps when it exceeds the maximum value." ::= { aRtgPnniCfgNodeNbrStatsEntry 4 } aRtgPnniCfgNodeNbrPtseReqRx OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the total number of PTSE requests received from the neighbor node. The counter wraps when it exceeds the maximum value." ::= { aRtgPnniCfgNodeNbrStatsEntry 5 } aRtgPnniCfgNodeNbrPtseReqTx OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the total number of PTSE requests sent to the neighbor node. The counter wraps when it exceeds the maximum value." ::= { aRtgPnniCfgNodeNbrStatsEntry 6 } aRtgPnniCfgNodeNbrPtseAcksRx OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the total number of PTSE acknowledgments received from the neighbor node. The counter wraps when it exceeds the maximum value." ::= { aRtgPnniCfgNodeNbrStatsEntry 7 } aRtgPnniCfgNodeNbrPtseAcksTx OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the total number of PTSE acknowledgments sent to the neighbor node. The counter wraps when it exceeds the maximum value." ::= { aRtgPnniCfgNodeNbrStatsEntry 8 } aRtgPnniCfgNodeNbrDbSummariesRx OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the number of database summary packets received from the neighbor. The counter wraps when it exceeds the maximum value." ::= { aRtgPnniCfgNodeNbrStatsEntry 9 } aRtgPnniCfgNodeNbrDbSummariesTx OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the number of database summary packets transmitted to the neighbor. The counter wraps when it exceeds the maximum value." ::= { aRtgPnniCfgNodeNbrStatsEntry 10 } aRtgPnniCfgNodeNbrBadPtspRx OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the total number of invalid PTSP packets received from the neighbor node. The counter wraps when it exceeds the maximum value." ::= { aRtgPnniCfgNodeNbrStatsEntry 11 } aRtgPnniCfgNodeNbrBadPtseRx OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the total number of invalid PTSE packets received to the neighbor node. The counter wraps when it exceeds the maximum value." ::= { aRtgPnniCfgNodeNbrStatsEntry 12 } aRtgPnniCfgNodeNbrBadPtseReqRx OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the total number of invalid PTSE requests received from the neighbor node. The counter wraps when it exceeds the maximum value." ::= { aRtgPnniCfgNodeNbrStatsEntry 13 } aRtgPnniCfgNodeNbrBadPtseAckRx OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the total number of invalid PTSE acknowledgments received from the neighbor node. The counter wraps when it exceeds the maximum value." ::= { aRtgPnniCfgNodeNbrStatsEntry 14 } aRtgPnniCfgNodeNbrBadDbSummariesRx OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute counts the total number of invalid database summary packets received from the neighbor. The counter wraps when it exceeds the maximum value." ::= { aRtgPnniCfgNodeNbrStatsEntry 15 } aRtgPnniCfgNodeNbrRccListTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniCfgNodeNbrRccListEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This attribute indicates the component names of all Routing Control Channels to the neighbor PNNI node." ::= { aRtgPnniCfgNodeNbr 385 } aRtgPnniCfgNodeNbrRccListEntry OBJECT-TYPE SYNTAX ARtgPnniCfgNodeNbrRccListEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the aRtgPnniCfgNodeNbrRccListTable." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniCfgNodeIndex, aRtgPnniCfgNodeNbrIndex, aRtgPnniCfgNodeNbrRccListValue } ::= { aRtgPnniCfgNodeNbrRccListTable 1 } ARtgPnniCfgNodeNbrRccListEntry ::= SEQUENCE { aRtgPnniCfgNodeNbrRccListValue RowPointer } aRtgPnniCfgNodeNbrRccListValue OBJECT-TYPE SYNTAX RowPointer ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents both the value and the index for the aRtgPnniCfgNodeNbrRccListTable." ::= { aRtgPnniCfgNodeNbrRccListEntry 1 } -- ARtg Pnni CfgNode/ DefSAddr -- A default summary address is an internal summary address -- computed for every logical group node as follows: -- If this is not the lowest configured node, then the default summary -- address is identical to the peer group id that this logical group -- represents. -- If this is the lowest configured node but not at level 104, then the -- default summary address is the 13-octet prefix of the node's -- address. -- A node at level 104 has no default summary address. aRtgPnniCfgNodeDefSAddr OBJECT IDENTIFIER ::= { aRtgPnniCfgNode 4 } aRtgPnniCfgNodeDefSAddrRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniCfgNodeDefSAddrRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of aRtgPnniCfgNodeDefSAddr components." ::= { aRtgPnniCfgNodeDefSAddr 1 } aRtgPnniCfgNodeDefSAddrRowStatusEntry OBJECT-TYPE SYNTAX ARtgPnniCfgNodeDefSAddrRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single aRtgPnniCfgNodeDefSAddr component." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniCfgNodeIndex, aRtgPnniCfgNodeDefSAddrIndex } ::= { aRtgPnniCfgNodeDefSAddrRowStatusTable 1 } ARtgPnniCfgNodeDefSAddrRowStatusEntry ::= SEQUENCE { aRtgPnniCfgNodeDefSAddrRowStatus RowStatus, aRtgPnniCfgNodeDefSAddrComponentName DisplayString, aRtgPnniCfgNodeDefSAddrStorageType StorageType, aRtgPnniCfgNodeDefSAddrIndex NonReplicated } aRtgPnniCfgNodeDefSAddrRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of aRtgPnniCfgNodeDefSAddr components. These components cannot be added nor deleted." ::= { aRtgPnniCfgNodeDefSAddrRowStatusEntry 1 } aRtgPnniCfgNodeDefSAddrComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { aRtgPnniCfgNodeDefSAddrRowStatusEntry 2 } aRtgPnniCfgNodeDefSAddrStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the aRtgPnniCfgNodeDefSAddr tables." ::= { aRtgPnniCfgNodeDefSAddrRowStatusEntry 4 } aRtgPnniCfgNodeDefSAddrIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the aRtgPnniCfgNodeDefSAddr tables." ::= { aRtgPnniCfgNodeDefSAddrRowStatusEntry 10 } aRtgPnniCfgNodeDefSAddrDefAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniCfgNodeDefSAddrDefAddrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the operational attributes of a DefSummaryAddress component." ::= { aRtgPnniCfgNodeDefSAddr 10 } aRtgPnniCfgNodeDefSAddrDefAddrEntry OBJECT-TYPE SYNTAX ARtgPnniCfgNodeDefSAddrDefAddrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the aRtgPnniCfgNodeDefSAddrDefAddrTable." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniCfgNodeIndex, aRtgPnniCfgNodeDefSAddrIndex } ::= { aRtgPnniCfgNodeDefSAddrDefAddrTable 1 } ARtgPnniCfgNodeDefSAddrDefAddrEntry ::= SEQUENCE { aRtgPnniCfgNodeDefSAddrAddress HexString } aRtgPnniCfgNodeDefSAddrAddress OBJECT-TYPE SYNTAX HexString (SIZE (13)) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the default summary address of the node at this level." ::= { aRtgPnniCfgNodeDefSAddrDefAddrEntry 1 } aRtgPnniCfgNodeDefSAddrOperTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniCfgNodeDefSAddrOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group contains the operational attributes of a SummaryAddress component." ::= { aRtgPnniCfgNodeDefSAddr 11 } aRtgPnniCfgNodeDefSAddrOperEntry OBJECT-TYPE SYNTAX ARtgPnniCfgNodeDefSAddrOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the aRtgPnniCfgNodeDefSAddrOperTable." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniCfgNodeIndex, aRtgPnniCfgNodeDefSAddrIndex } ::= { aRtgPnniCfgNodeDefSAddrOperTable 1 } ARtgPnniCfgNodeDefSAddrOperEntry ::= SEQUENCE { aRtgPnniCfgNodeDefSAddrState INTEGER, aRtgPnniCfgNodeDefSAddrScope INTEGER } aRtgPnniCfgNodeDefSAddrState OBJECT-TYPE SYNTAX INTEGER { advertising(0), suppressing(1), inactive(2) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the state of the address: one of advertising, suppressing or inactive. inactive: the summary address has been configured but is not suppressing or summarizing any ATM addresses. suppressing: the summary address has suppressed at least one ATM address on the node. advertising: the summary address is summarizing at least one ATM address on the node." ::= { aRtgPnniCfgNodeDefSAddrOperEntry 1 } aRtgPnniCfgNodeDefSAddrScope OBJECT-TYPE SYNTAX INTEGER (-1..104) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the scope of the summary address. The scope corresponds to the scope of the underlying summarized address with the highest advertised scope. A value of -1 means the scope is unknown." ::= { aRtgPnniCfgNodeDefSAddrOperEntry 2 } -- -- *** THIS SUBTREE CURRENTLY NOT IMPLEMENTED *** -- -- ARtg Pnni Topology/ -- -- The Topology component provides access to information in this -- node's PNNI topology database for a particular level in the PNNI -- hierarchy. aRtgPnniTop OBJECT IDENTIFIER ::= { aRtgPnni 4 } aRtgPnniTopRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniTopRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This entry controls the addition and deletion of aRtgPnniTop components." ::= { aRtgPnniTop 1 } aRtgPnniTopRowStatusEntry OBJECT-TYPE SYNTAX ARtgPnniTopRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single aRtgPnniTop component." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniTopIndex } ::= { aRtgPnniTopRowStatusTable 1 } ARtgPnniTopRowStatusEntry ::= SEQUENCE { aRtgPnniTopRowStatus RowStatus, aRtgPnniTopComponentName DisplayString, aRtgPnniTopStorageType StorageType, aRtgPnniTopIndex Integer32 } aRtgPnniTopRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of aRtgPnniTop components. These components cannot be added nor deleted." ::= { aRtgPnniTopRowStatusEntry 1 } aRtgPnniTopComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { aRtgPnniTopRowStatusEntry 2 } aRtgPnniTopStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the aRtgPnniTop tables." ::= { aRtgPnniTopRowStatusEntry 4 } aRtgPnniTopIndex OBJECT-TYPE SYNTAX Integer32 (0..104) ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the aRtgPnniTop tables." ::= { aRtgPnniTopRowStatusEntry 10 } aRtgPnniTopOperTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniTopOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains the operational attributes of a Topology component." ::= { aRtgPnniTop 10 } aRtgPnniTopOperEntry OBJECT-TYPE SYNTAX ARtgPnniTopOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the aRtgPnniTopOperTable." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniTopIndex } ::= { aRtgPnniTopOperTable 1 } ARtgPnniTopOperEntry ::= SEQUENCE { aRtgPnniTopPtsesInDatabase Gauge32, aRtgPnniTopPglNodeId HexString, aRtgPnniTopActiveParentNodeId HexString, aRtgPnniTopPreferredPglNodeId HexString } aRtgPnniTopPtsesInDatabase OBJECT-TYPE SYNTAX Gauge32 (0..4294967295) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the number of PTSEs in storage in this node's topology database for this level." ::= { aRtgPnniTopOperEntry 1 } aRtgPnniTopPglNodeId OBJECT-TYPE SYNTAX HexString (SIZE (0..22)) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the node id of the peer group leader. If this attribute is empty, it indicates the Peer Group Level node id is unknown." ::= { aRtgPnniTopOperEntry 2 } aRtgPnniTopActiveParentNodeId OBJECT-TYPE SYNTAX HexString (SIZE (0..22)) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the node identifier being used by the LGN representing this peer group at the next higher level peer group." ::= { aRtgPnniTopOperEntry 3 } aRtgPnniTopPreferredPglNodeId OBJECT-TYPE SYNTAX HexString (SIZE (0..22)) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute represents the node in database with the highest Peer Group Level (PGL) priority. If this attribute is empty, it indicates the preferred PGL node id is unknown." ::= { aRtgPnniTopOperEntry 4 } -- -- *** THIS SUBTREE CURRENTLY NOT IMPLEMENTED *** -- -- ARtg Pnni Top/ Node/ -- This component represents the nodal information stored in this -- node's topology database. -- -- The reachable ATM end system addresses (both interior and -- exterior reachable addresses) advertised by the node can be listed -- through the Addr subcomponent instances. -- -- All advertised links associated with the node can be listed through -- the Link subcomponent instances which are indexed by their port id. aRtgPnniTopNode OBJECT IDENTIFIER ::= { aRtgPnniTop 2 } aRtgPnniTopNodeRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniTopNodeRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This entry controls the addition and deletion of aRtgPnniTopNode components." ::= { aRtgPnniTopNode 1 } aRtgPnniTopNodeRowStatusEntry OBJECT-TYPE SYNTAX ARtgPnniTopNodeRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single aRtgPnniTopNode component." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniTopIndex, aRtgPnniTopNodeIndex } ::= { aRtgPnniTopNodeRowStatusTable 1 } ARtgPnniTopNodeRowStatusEntry ::= SEQUENCE { aRtgPnniTopNodeRowStatus RowStatus, aRtgPnniTopNodeComponentName DisplayString, aRtgPnniTopNodeStorageType StorageType, aRtgPnniTopNodeIndex HexString } aRtgPnniTopNodeRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of aRtgPnniTopNode components. These components cannot be added nor deleted." ::= { aRtgPnniTopNodeRowStatusEntry 1 } aRtgPnniTopNodeComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { aRtgPnniTopNodeRowStatusEntry 2 } aRtgPnniTopNodeStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the aRtgPnniTopNode tables." ::= { aRtgPnniTopNodeRowStatusEntry 4 } aRtgPnniTopNodeIndex OBJECT-TYPE SYNTAX HexString (SIZE (22)) ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the aRtgPnniTopNode tables." ::= { aRtgPnniTopNodeRowStatusEntry 10 } -- -- *** THIS SUBTREE CURRENTLY NOT IMPLEMENTED *** -- -- ARtg Pnni Top Node/ Address/
, -- , -- This component represents an address advertised by the parent -- node. The instance value is a 38 hex digit string. -- -- The prefixLength specifies the number of significant bits in the -- address. -- -- The reachability specifies whether the address is internal or -- exterior. -- An internal reachable address is an address of a destination that is -- directly attached to the logical node advertising the address. An -- exterior reachable address is an address that can be reached -- through a PNNI routing domain, but which is not located in that -- PNNI routing domain. aRtgPnniTopNodeAddr OBJECT IDENTIFIER ::= { aRtgPnniTopNode 2 } aRtgPnniTopNodeAddrRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniTopNodeAddrRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This entry controls the addition and deletion of aRtgPnniTopNodeAddr components." ::= { aRtgPnniTopNodeAddr 1 } aRtgPnniTopNodeAddrRowStatusEntry OBJECT-TYPE SYNTAX ARtgPnniTopNodeAddrRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single aRtgPnniTopNodeAddr component." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniTopIndex, aRtgPnniTopNodeIndex, aRtgPnniTopNodeAddrAddressIndex, aRtgPnniTopNodeAddrPrefixLengthIndex, aRtgPnniTopNodeAddrReachabilityIndex } ::= { aRtgPnniTopNodeAddrRowStatusTable 1 } ARtgPnniTopNodeAddrRowStatusEntry ::= SEQUENCE { aRtgPnniTopNodeAddrRowStatus RowStatus, aRtgPnniTopNodeAddrComponentName DisplayString, aRtgPnniTopNodeAddrStorageType StorageType, aRtgPnniTopNodeAddrAddressIndex HexString, aRtgPnniTopNodeAddrPrefixLengthIndex Integer32, aRtgPnniTopNodeAddrReachabilityIndex INTEGER } aRtgPnniTopNodeAddrRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of aRtgPnniTopNodeAddr components. These components cannot be added nor deleted." ::= { aRtgPnniTopNodeAddrRowStatusEntry 1 } aRtgPnniTopNodeAddrComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { aRtgPnniTopNodeAddrRowStatusEntry 2 } aRtgPnniTopNodeAddrStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the aRtgPnniTopNodeAddr tables." ::= { aRtgPnniTopNodeAddrRowStatusEntry 4 } aRtgPnniTopNodeAddrAddressIndex OBJECT-TYPE SYNTAX HexString (SIZE (19)) ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents an index for the aRtgPnniTopNodeAddr tables." ::= { aRtgPnniTopNodeAddrRowStatusEntry 10 } aRtgPnniTopNodeAddrPrefixLengthIndex OBJECT-TYPE SYNTAX Integer32 (1..152) ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents an index for the aRtgPnniTopNodeAddr tables." ::= { aRtgPnniTopNodeAddrRowStatusEntry 11 } aRtgPnniTopNodeAddrReachabilityIndex OBJECT-TYPE SYNTAX INTEGER { internal(0), exterior(1) } ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents an index for the aRtgPnniTopNodeAddr tables." ::= { aRtgPnniTopNodeAddrRowStatusEntry 12 } aRtgPnniTopNodeAddrOperTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniTopNodeAddrOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This attribute group contains the operational attributes for the Address component." ::= { aRtgPnniTopNodeAddr 10 } aRtgPnniTopNodeAddrOperEntry OBJECT-TYPE SYNTAX ARtgPnniTopNodeAddrOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the aRtgPnniTopNodeAddrOperTable." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniTopIndex, aRtgPnniTopNodeIndex, aRtgPnniTopNodeAddrAddressIndex, aRtgPnniTopNodeAddrPrefixLengthIndex, aRtgPnniTopNodeAddrReachabilityIndex } ::= { aRtgPnniTopNodeAddrOperTable 1 } ARtgPnniTopNodeAddrOperEntry ::= SEQUENCE { aRtgPnniTopNodeAddrScope Unsigned32 } aRtgPnniTopNodeAddrScope OBJECT-TYPE SYNTAX Unsigned32 (0..104) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute specifies the scope of the ATM address, which is the highest level to which this address will be advertised in the PNNI hierarchy." ::= { aRtgPnniTopNodeAddrOperEntry 1 } -- -- *** THIS SUBTREE CURRENTLY NOT IMPLEMENTED *** -- -- ARtg Pnni Top/ Node/ Link/ -- This component represents the link information stored in this node's -- topology database. -- -- All advertised links associated with the node can be listed through -- the Link subcomponent instances which are indexed by their port id. aRtgPnniTopNodeLink OBJECT IDENTIFIER ::= { aRtgPnniTopNode 3 } aRtgPnniTopNodeLinkRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniTopNodeLinkRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This entry controls the addition and deletion of aRtgPnniTopNodeLink components." ::= { aRtgPnniTopNodeLink 1 } aRtgPnniTopNodeLinkRowStatusEntry OBJECT-TYPE SYNTAX ARtgPnniTopNodeLinkRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single aRtgPnniTopNodeLink component." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniTopIndex, aRtgPnniTopNodeIndex, aRtgPnniTopNodeLinkIndex } ::= { aRtgPnniTopNodeLinkRowStatusTable 1 } ARtgPnniTopNodeLinkRowStatusEntry ::= SEQUENCE { aRtgPnniTopNodeLinkRowStatus RowStatus, aRtgPnniTopNodeLinkComponentName DisplayString, aRtgPnniTopNodeLinkStorageType StorageType, aRtgPnniTopNodeLinkIndex Integer32 } aRtgPnniTopNodeLinkRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of aRtgPnniTopNodeLink components. These components cannot be added nor deleted." ::= { aRtgPnniTopNodeLinkRowStatusEntry 1 } aRtgPnniTopNodeLinkComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { aRtgPnniTopNodeLinkRowStatusEntry 2 } aRtgPnniTopNodeLinkStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the aRtgPnniTopNodeLink tables." ::= { aRtgPnniTopNodeLinkRowStatusEntry 4 } aRtgPnniTopNodeLinkIndex OBJECT-TYPE SYNTAX Integer32 (0..268435455) ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the aRtgPnniTopNodeLink tables." ::= { aRtgPnniTopNodeLinkRowStatusEntry 10 } aRtgPnniTopNodeLinkOperTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniTopNodeLinkOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains the operational attributes of a Link component." ::= { aRtgPnniTopNodeLink 10 } aRtgPnniTopNodeLinkOperEntry OBJECT-TYPE SYNTAX ARtgPnniTopNodeLinkOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the aRtgPnniTopNodeLinkOperTable." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniTopIndex, aRtgPnniTopNodeIndex, aRtgPnniTopNodeLinkIndex } ::= { aRtgPnniTopNodeLinkOperTable 1 } ARtgPnniTopNodeLinkOperEntry ::= SEQUENCE { aRtgPnniTopNodeLinkRemoteNodeId HexString, aRtgPnniTopNodeLinkRemotePortId Unsigned32 } aRtgPnniTopNodeLinkRemoteNodeId OBJECT-TYPE SYNTAX HexString (SIZE (22)) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the id of the node at the far end of this link." ::= { aRtgPnniTopNodeLinkOperEntry 1 } aRtgPnniTopNodeLinkRemotePortId OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the node's port id at the far end of this link." ::= { aRtgPnniTopNodeLinkOperEntry 2 } -- -- *** THIS SUBTREE CURRENTLY NOT IMPLEMENTED *** -- -- ARtg Pnni Port/ -- This component represents a port advertised within the PNNI -- routing domain. aRtgPnniPort OBJECT IDENTIFIER ::= { aRtgPnni 5 } aRtgPnniPortRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniPortRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This entry controls the addition and deletion of aRtgPnniPort components." ::= { aRtgPnniPort 1 } aRtgPnniPortRowStatusEntry OBJECT-TYPE SYNTAX ARtgPnniPortRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single aRtgPnniPort component." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniPortIndex } ::= { aRtgPnniPortRowStatusTable 1 } ARtgPnniPortRowStatusEntry ::= SEQUENCE { aRtgPnniPortRowStatus RowStatus, aRtgPnniPortComponentName DisplayString, aRtgPnniPortStorageType StorageType, aRtgPnniPortIndex Integer32 } aRtgPnniPortRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of aRtgPnniPort components. These components cannot be added nor deleted." ::= { aRtgPnniPortRowStatusEntry 1 } aRtgPnniPortComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { aRtgPnniPortRowStatusEntry 2 } aRtgPnniPortStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the aRtgPnniPort tables." ::= { aRtgPnniPortRowStatusEntry 4 } aRtgPnniPortIndex OBJECT-TYPE SYNTAX Integer32 (0..268435455) ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the aRtgPnniPort tables." ::= { aRtgPnniPortRowStatusEntry 10 } aRtgPnniPortOperTable OBJECT-TYPE SYNTAX SEQUENCE OF ARtgPnniPortOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains the operational attributes of a Port component." ::= { aRtgPnniPort 10 } aRtgPnniPortOperEntry OBJECT-TYPE SYNTAX ARtgPnniPortOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the aRtgPnniPortOperTable." INDEX { aRtgIndex, aRtgPnniIndex, aRtgPnniPortIndex } ::= { aRtgPnniPortOperTable 1 } ARtgPnniPortOperEntry ::= SEQUENCE { aRtgPnniPortStdComponentName RowPointer } aRtgPnniPortStdComponentName OBJECT-TYPE SYNTAX RowPointer ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the component name of the port." ::= { aRtgPnniPortOperEntry 1 } -- AtmCallRouter -- This component represents the database that contains all the static -- (provisioned) DNAs and dynamically registered DNAs (via ILMI) -- used for source call routing for ATM switched connection setups.. atmCR OBJECT IDENTIFIER ::= { components 113 } atmCRRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmCRRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of atmCR components." ::= { atmCR 1 } atmCRRowStatusEntry OBJECT-TYPE SYNTAX AtmCRRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single atmCR component." INDEX { atmCRIndex } ::= { atmCRRowStatusTable 1 } AtmCRRowStatusEntry ::= SEQUENCE { atmCRRowStatus RowStatus, atmCRComponentName DisplayString, atmCRStorageType StorageType, atmCRIndex NonReplicated } atmCRRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-write STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of atmCR components. These components can be added and deleted." ::= { atmCRRowStatusEntry 1 } atmCRComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { atmCRRowStatusEntry 2 } atmCRStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the atmCR tables." ::= { atmCRRowStatusEntry 4 } atmCRIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the atmCR tables." ::= { atmCRRowStatusEntry 10 } atmCRProvTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmCRProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This group represents the provisioned attributes for the AtmCallRouter component." ::= { atmCR 10 } atmCRProvEntry OBJECT-TYPE SYNTAX AtmCRProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmCRProvTable." INDEX { atmCRIndex } ::= { atmCRProvTable 1 } AtmCRProvEntry ::= SEQUENCE { atmCRNodeAddress AsciiString } atmCRNodeAddress OBJECT-TYPE SYNTAX AsciiString (SIZE (26)) ACCESS read-write STATUS obsolete DESCRIPTION "This attribute specifies the NSAP address prefix used for ILMI purposes." ::= { atmCRProvEntry 1 } atmCRStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmCRStatsEntry ACCESS not-accessible STATUS obsolete DESCRIPTION "This group represents the operational attributes for the AtmCallRouter component." ::= { atmCR 11 } atmCRStatsEntry OBJECT-TYPE SYNTAX AtmCRStatsEntry ACCESS not-accessible STATUS obsolete DESCRIPTION "An entry in the atmCRStatsTable." INDEX { atmCRIndex } ::= { atmCRStatsTable 1 } AtmCRStatsEntry ::= SEQUENCE { atmCRCallsRouted Counter32, atmCRCallsFailed Counter32 } atmCRCallsRouted OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS obsolete DESCRIPTION "This attribute counts the total number of calls routed." ::= { atmCRStatsEntry 1 } atmCRCallsFailed OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS obsolete DESCRIPTION "This attribute specifies the number of calls that failed to route." ::= { atmCRStatsEntry 2 } -- -- *** THIS SUBTREE CURRENTLY NOT IMPLEMENTED *** -- -- AtmCallRouter AtmDna/ -- This component represents an ATM NSAP address that has been -- provisioned or dynamically registered via ILMI. atmCRDna OBJECT IDENTIFIER ::= { atmCR 2 } atmCRDnaRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmCRDnaRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This entry controls the addition and deletion of atmCRDna components." ::= { atmCRDna 1 } atmCRDnaRowStatusEntry OBJECT-TYPE SYNTAX AtmCRDnaRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single atmCRDna component." INDEX { atmCRIndex, atmCRDnaIndex } ::= { atmCRDnaRowStatusTable 1 } AtmCRDnaRowStatusEntry ::= SEQUENCE { atmCRDnaRowStatus RowStatus, atmCRDnaComponentName DisplayString, atmCRDnaStorageType StorageType, atmCRDnaIndex AsciiStringIndex } atmCRDnaRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of atmCRDna components. These components cannot be added nor deleted." ::= { atmCRDnaRowStatusEntry 1 } atmCRDnaComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { atmCRDnaRowStatusEntry 2 } atmCRDnaStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the atmCRDna tables." ::= { atmCRDnaRowStatusEntry 4 } atmCRDnaIndex OBJECT-TYPE SYNTAX AsciiStringIndex (SIZE (1..40)) ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the atmCRDna tables." ::= { atmCRDnaRowStatusEntry 10 } atmCRDnaDestinationNameTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmCRDnaDestinationNameEntry ACCESS not-accessible STATUS obsolete DESCRIPTION "*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This attribute indicates which components have this address provisioned or dynamically registered via ILMI." ::= { atmCRDna 289 } atmCRDnaDestinationNameEntry OBJECT-TYPE SYNTAX AtmCRDnaDestinationNameEntry ACCESS not-accessible STATUS obsolete DESCRIPTION "An entry in the atmCRDnaDestinationNameTable." INDEX { atmCRIndex, atmCRDnaIndex, atmCRDnaDestinationNameValue } ::= { atmCRDnaDestinationNameTable 1 } AtmCRDnaDestinationNameEntry ::= SEQUENCE { atmCRDnaDestinationNameValue RowPointer } atmCRDnaDestinationNameValue OBJECT-TYPE SYNTAX RowPointer ACCESS read-only STATUS obsolete DESCRIPTION "This variable represents both the value and the index for the atmCRDnaDestinationNameTable." ::= { atmCRDnaDestinationNameEntry 1 } -- AtmIf/n Vpc/vpi SourcePvp -- This component represents the source end of a soft PVP. atmIfVpcSrc OBJECT IDENTIFIER ::= { atmIfVpc 6 } atmIfVpcSrcRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVpcSrcRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of atmIfVpcSrc components." ::= { atmIfVpcSrc 1 } atmIfVpcSrcRowStatusEntry OBJECT-TYPE SYNTAX AtmIfVpcSrcRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single atmIfVpcSrc component." INDEX { atmIfIndex, atmIfVpcIndex, atmIfVpcSrcIndex } ::= { atmIfVpcSrcRowStatusTable 1 } AtmIfVpcSrcRowStatusEntry ::= SEQUENCE { atmIfVpcSrcRowStatus RowStatus, atmIfVpcSrcComponentName DisplayString, atmIfVpcSrcStorageType StorageType, atmIfVpcSrcIndex NonReplicated } atmIfVpcSrcRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-write STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of atmIfVpcSrc components. These components can be added and deleted." ::= { atmIfVpcSrcRowStatusEntry 1 } atmIfVpcSrcComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { atmIfVpcSrcRowStatusEntry 2 } atmIfVpcSrcStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the atmIfVpcSrc tables." ::= { atmIfVpcSrcRowStatusEntry 4 } atmIfVpcSrcIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the atmIfVpcSrc tables." ::= { atmIfVpcSrcRowStatusEntry 10 } atmIfVpcSrcProvTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVpcSrcProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute group contains the provisionable attributes of the AtmIf/n Vpc/vpi SrcPvp component." ::= { atmIfVpcSrc 10 } atmIfVpcSrcProvEntry OBJECT-TYPE SYNTAX AtmIfVpcSrcProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfVpcSrcProvTable." INDEX { atmIfIndex, atmIfVpcIndex, atmIfVpcSrcIndex } ::= { atmIfVpcSrcProvTable 1 } AtmIfVpcSrcProvEntry ::= SEQUENCE { atmIfVpcSrcCallingAddress HexString, atmIfVpcSrcCalledAddress HexString, atmIfVpcSrcCalledVpi Unsigned32 } atmIfVpcSrcCallingAddress OBJECT-TYPE SYNTAX HexString (SIZE (0..20)) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the calling address of the soft PVP. If it is a null string, then the calling address is the address of the current interface (that is, where the soft PVC originates)." DEFVAL { ''H } -- "" ::= { atmIfVpcSrcProvEntry 1 } atmIfVpcSrcCalledAddress OBJECT-TYPE SYNTAX HexString (SIZE (20)) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the called (remote) address of the soft PVP." ::= { atmIfVpcSrcProvEntry 2 } atmIfVpcSrcCalledVpi OBJECT-TYPE SYNTAX Unsigned32 (1..4095) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the called VPI of the soft PVP." ::= { atmIfVpcSrcProvEntry 3 } atmIfVpcSrcOperTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVpcSrcOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute group contains the operational attributes associated with the SrcPvp or SrcPvc component." ::= { atmIfVpcSrc 11 } atmIfVpcSrcOperEntry OBJECT-TYPE SYNTAX AtmIfVpcSrcOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfVpcSrcOperTable." INDEX { atmIfIndex, atmIfVpcIndex, atmIfVpcSrcIndex } ::= { atmIfVpcSrcOperTable 1 } AtmIfVpcSrcOperEntry ::= SEQUENCE { atmIfVpcSrcState INTEGER, atmIfVpcSrcRetryCount Counter32, atmIfVpcSrcLastFailureCauseCode Unsigned32, atmIfVpcSrcLastFailureDiagCode AsciiString } atmIfVpcSrcState OBJECT-TYPE SYNTAX INTEGER { active(0), inactive(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the state of the soft PVP or soft PVC." ::= { atmIfVpcSrcOperEntry 1 } atmIfVpcSrcRetryCount OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the number of failed attempts to set up the soft PVP or soft PVC since the last time the connection failed." ::= { atmIfVpcSrcOperEntry 2 } atmIfVpcSrcLastFailureCauseCode OBJECT-TYPE SYNTAX Unsigned32 (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute contains the cause code in the last transmitted signalling message that contains the CAUSE information element. The cause code is used to describe the reason for generating certain signalling messages. The default value for this attribute is set to 0." ::= { atmIfVpcSrcOperEntry 3 } atmIfVpcSrcLastFailureDiagCode OBJECT-TYPE SYNTAX AsciiString (SIZE (0..8)) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute contains the diagnostic code in the last transmitted signalling message. The diagnostic code is contained in the CAUSE information element and identifies an information element type or timer type. The diagnostic code is present only if a procedural error is detected by the signalling protocol. A diagnostic code is always accompanied by the cause code. If there is no failure, this attribute is set to NULL." ::= { atmIfVpcSrcOperEntry 4 } -- AtmIf/n Vpc/vpi Rp -- AtmIf/n Vcc/vpi.vci Rp -- AtmIf/n Vpt/vpi Vcc/vci Rp -- -- The RelayPoint component is used to establish a single hop of a -- Switched connection. When linked together, two Rps within a -- module, the associated connections are configured to relay ATM -- cells to one another. atmIfVpcRp OBJECT IDENTIFIER ::= { atmIfVpc 7 } atmIfVpcRpRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVpcRpRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of atmIfVpcRp components." ::= { atmIfVpcRp 1 } atmIfVpcRpRowStatusEntry OBJECT-TYPE SYNTAX AtmIfVpcRpRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single atmIfVpcRp component." INDEX { atmIfIndex, atmIfVpcIndex, atmIfVpcRpIndex } ::= { atmIfVpcRpRowStatusTable 1 } AtmIfVpcRpRowStatusEntry ::= SEQUENCE { atmIfVpcRpRowStatus RowStatus, atmIfVpcRpComponentName DisplayString, atmIfVpcRpStorageType StorageType, atmIfVpcRpIndex NonReplicated } atmIfVpcRpRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of atmIfVpcRp components. These components cannot be added nor deleted." ::= { atmIfVpcRpRowStatusEntry 1 } atmIfVpcRpComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { atmIfVpcRpRowStatusEntry 2 } atmIfVpcRpStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the atmIfVpcRp tables." ::= { atmIfVpcRpRowStatusEntry 4 } atmIfVpcRpIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the atmIfVpcRp tables." ::= { atmIfVpcRpRowStatusEntry 10 } atmIfVpcRpOperTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVpcRpOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute group contains the operational attributes for the AtmRelayPoint component." ::= { atmIfVpcRp 10 } atmIfVpcRpOperEntry OBJECT-TYPE SYNTAX AtmIfVpcRpOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfVpcRpOperTable." INDEX { atmIfIndex, atmIfVpcIndex, atmIfVpcRpIndex } ::= { atmIfVpcRpOperTable 1 } AtmIfVpcRpOperEntry ::= SEQUENCE { atmIfVpcRpNextHop RowPointer } atmIfVpcRpNextHop OBJECT-TYPE SYNTAX RowPointer ACCESS read-only STATUS obsolete DESCRIPTION "This attribute indicates the component name of the Rp component with which this Rp component is associated." ::= { atmIfVpcRpOperEntry 1 } atmIfVpcRpNextHopsTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVpcRpNextHopsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute indicates the component name(s) of the Rp component(s) with which this Rp component is associated. This attribute can have more than one component name only when the Vcc distributionType is pointToMultipoint and the callDirection is fromLink." ::= { atmIfVpcRp 430 } atmIfVpcRpNextHopsEntry OBJECT-TYPE SYNTAX AtmIfVpcRpNextHopsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfVpcRpNextHopsTable." INDEX { atmIfIndex, atmIfVpcIndex, atmIfVpcRpIndex, atmIfVpcRpNextHopsValue } ::= { atmIfVpcRpNextHopsTable 1 } AtmIfVpcRpNextHopsEntry ::= SEQUENCE { atmIfVpcRpNextHopsValue RowPointer } atmIfVpcRpNextHopsValue OBJECT-TYPE SYNTAX RowPointer ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents both the value and the index for the atmIfVpcRpNextHopsTable." ::= { atmIfVpcRpNextHopsEntry 1 } -- AtmIf/n Vpc/vpi DestinationPvp -- This component represents the destination end of a soft PVP. atmIfVpcDst OBJECT IDENTIFIER ::= { atmIfVpc 8 } atmIfVpcDstRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVpcDstRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of atmIfVpcDst components." ::= { atmIfVpcDst 1 } atmIfVpcDstRowStatusEntry OBJECT-TYPE SYNTAX AtmIfVpcDstRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single atmIfVpcDst component." INDEX { atmIfIndex, atmIfVpcIndex, atmIfVpcDstIndex } ::= { atmIfVpcDstRowStatusTable 1 } AtmIfVpcDstRowStatusEntry ::= SEQUENCE { atmIfVpcDstRowStatus RowStatus, atmIfVpcDstComponentName DisplayString, atmIfVpcDstStorageType StorageType, atmIfVpcDstIndex NonReplicated } atmIfVpcDstRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of atmIfVpcDst components. These components cannot be added nor deleted." ::= { atmIfVpcDstRowStatusEntry 1 } atmIfVpcDstComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { atmIfVpcDstRowStatusEntry 2 } atmIfVpcDstStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the atmIfVpcDst tables." ::= { atmIfVpcDstRowStatusEntry 4 } atmIfVpcDstIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the atmIfVpcDst tables." ::= { atmIfVpcDstRowStatusEntry 10 } atmIfVpcDstOperTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVpcDstOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute group contains the operational attributes for the AtmIf/n Vpc/vpi DstPvp component." ::= { atmIfVpcDst 10 } atmIfVpcDstOperEntry OBJECT-TYPE SYNTAX AtmIfVpcDstOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfVpcDstOperTable." INDEX { atmIfIndex, atmIfVpcIndex, atmIfVpcDstIndex } ::= { atmIfVpcDstOperTable 1 } AtmIfVpcDstOperEntry ::= SEQUENCE { atmIfVpcDstCalledAddress HexString, atmIfVpcDstCallingAddress AsciiString, atmIfVpcDstCallingVpi AsciiString } atmIfVpcDstCalledAddress OBJECT-TYPE SYNTAX HexString (SIZE (20)) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the called address of the soft PVP." ::= { atmIfVpcDstOperEntry 1 } atmIfVpcDstCallingAddress OBJECT-TYPE SYNTAX AsciiString (SIZE (7..40)) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the calling (remote) address of the soft PVP. If the address in not known, then the value of this address is Unknown." ::= { atmIfVpcDstOperEntry 2 } atmIfVpcDstCallingVpi OBJECT-TYPE SYNTAX AsciiString (SIZE (1..7)) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute represents the calling (remote) VPI of the soft PVP. If the VPI value is not known, the attribute value is set to Unknown." ::= { atmIfVpcDstOperEntry 3 } -- AtmIf/n Vcc/vpi.vci SrcPvc -- AtmIf/n Vpt/vpi Vcc/vci SrcPvc -- -- This component represents the source end of a soft PVC. atmIfVccSrc OBJECT IDENTIFIER ::= { atmIfVcc 8 } atmIfVccSrcRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVccSrcRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of atmIfVccSrc components." ::= { atmIfVccSrc 1 } atmIfVccSrcRowStatusEntry OBJECT-TYPE SYNTAX AtmIfVccSrcRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single atmIfVccSrc component." INDEX { atmIfIndex, atmIfVccIndex, atmIfVccSrcIndex } ::= { atmIfVccSrcRowStatusTable 1 } AtmIfVccSrcRowStatusEntry ::= SEQUENCE { atmIfVccSrcRowStatus RowStatus, atmIfVccSrcComponentName DisplayString, atmIfVccSrcStorageType StorageType, atmIfVccSrcIndex NonReplicated } atmIfVccSrcRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-write STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of atmIfVccSrc components. These components can be added and deleted." ::= { atmIfVccSrcRowStatusEntry 1 } atmIfVccSrcComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { atmIfVccSrcRowStatusEntry 2 } atmIfVccSrcStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the atmIfVccSrc tables." ::= { atmIfVccSrcRowStatusEntry 4 } atmIfVccSrcIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the atmIfVccSrc tables." ::= { atmIfVccSrcRowStatusEntry 10 } atmIfVccSrcProvTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVccSrcProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute group contains the provisionable attributes of the SourcePvc component." ::= { atmIfVccSrc 10 } atmIfVccSrcProvEntry OBJECT-TYPE SYNTAX AtmIfVccSrcProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfVccSrcProvTable." INDEX { atmIfIndex, atmIfVccIndex, atmIfVccSrcIndex } ::= { atmIfVccSrcProvTable 1 } AtmIfVccSrcProvEntry ::= SEQUENCE { atmIfVccSrcRemoteAddress HexString, atmIfVccSrcRemoteVpiVci IntegerSequence, atmIfVccSrcCallingAddress HexString, atmIfVccSrcCalledAddress HexString, atmIfVccSrcCalledVpiVci IntegerSequence } atmIfVccSrcRemoteAddress OBJECT-TYPE SYNTAX HexString (SIZE (20)) ACCESS read-write STATUS obsolete DESCRIPTION "This attribute represents the remote address of the soft PVC." ::= { atmIfVccSrcProvEntry 1 } atmIfVccSrcRemoteVpiVci OBJECT-TYPE SYNTAX IntegerSequence (SIZE (3..9)) ACCESS read-write STATUS obsolete DESCRIPTION "This attribute represents the remote VPI and VCI of the soft PVC." ::= { atmIfVccSrcProvEntry 2 } atmIfVccSrcCallingAddress OBJECT-TYPE SYNTAX HexString (SIZE (0..20)) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute represents the calling address of the soft PVC. If it is a null string, then the calling address is the address of the current interface (that is, where the soft PVC originates)." DEFVAL { ''H } -- "" ::= { atmIfVccSrcProvEntry 3 } atmIfVccSrcCalledAddress OBJECT-TYPE SYNTAX HexString (SIZE (20)) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute represents the called (remote) address of the soft PVC." ::= { atmIfVccSrcProvEntry 4 } atmIfVccSrcCalledVpiVci OBJECT-TYPE SYNTAX IntegerSequence (SIZE (3..10)) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute represents the remote VPI and VCI of the soft PVC." ::= { atmIfVccSrcProvEntry 5 } atmIfVccSrcOperTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVccSrcOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute group contains the operational attributes associated with the SrcPvp or SrcPvc component." ::= { atmIfVccSrc 11 } atmIfVccSrcOperEntry OBJECT-TYPE SYNTAX AtmIfVccSrcOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfVccSrcOperTable." INDEX { atmIfIndex, atmIfVccIndex, atmIfVccSrcIndex } ::= { atmIfVccSrcOperTable 1 } AtmIfVccSrcOperEntry ::= SEQUENCE { atmIfVccSrcState INTEGER, atmIfVccSrcRetryCount Counter32, atmIfVccSrcLastFailureCauseCode Unsigned32, atmIfVccSrcLastFailureDiagCode AsciiString } atmIfVccSrcState OBJECT-TYPE SYNTAX INTEGER { active(0), inactive(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the state of the soft PVP or soft PVC." ::= { atmIfVccSrcOperEntry 1 } atmIfVccSrcRetryCount OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the number of failed attempts to set up the soft PVP or soft PVC since the last time the connection failed." ::= { atmIfVccSrcOperEntry 2 } atmIfVccSrcLastFailureCauseCode OBJECT-TYPE SYNTAX Unsigned32 (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute contains the cause code in the last transmitted signalling message that contains the CAUSE information element. The cause code is used to describe the reason for generating certain signalling messages. The default value for this attribute is set to 0." ::= { atmIfVccSrcOperEntry 3 } atmIfVccSrcLastFailureDiagCode OBJECT-TYPE SYNTAX AsciiString (SIZE (0..8)) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute contains the diagnostic code in the last transmitted signalling message. The diagnostic code is contained in the CAUSE information element and identifies an information element type or timer type. The diagnostic code is present only if a procedural error is detected by the signalling protocol. A diagnostic code is always accompanied by the cause code. If there is no failure, this attribute is set to NULL." ::= { atmIfVccSrcOperEntry 4 } -- AtmIf/n Vcc/vpi.vci Ep -- AtmIf/n Vpt/vpi Vcc/vci Ep -- -- The EndPoint component of the application associated with the -- VCC is used to link a switched VCC to an application that sends -- and receives frames using the connection. atmIfVccEp OBJECT IDENTIFIER ::= { atmIfVcc 9 } atmIfVccEpRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVccEpRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of atmIfVccEp components." ::= { atmIfVccEp 1 } atmIfVccEpRowStatusEntry OBJECT-TYPE SYNTAX AtmIfVccEpRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single atmIfVccEp component." INDEX { atmIfIndex, atmIfVccIndex, atmIfVccEpIndex } ::= { atmIfVccEpRowStatusTable 1 } AtmIfVccEpRowStatusEntry ::= SEQUENCE { atmIfVccEpRowStatus RowStatus, atmIfVccEpComponentName DisplayString, atmIfVccEpStorageType StorageType, atmIfVccEpIndex NonReplicated } atmIfVccEpRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of atmIfVccEp components. These components cannot be added nor deleted." ::= { atmIfVccEpRowStatusEntry 1 } atmIfVccEpComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { atmIfVccEpRowStatusEntry 2 } atmIfVccEpStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the atmIfVccEp tables." ::= { atmIfVccEpRowStatusEntry 4 } atmIfVccEpIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the atmIfVccEp tables." ::= { atmIfVccEpRowStatusEntry 10 } atmIfVccEpOperTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVccEpOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute group contains the operational attributes for the AtmEndPoint component." ::= { atmIfVccEp 10 } atmIfVccEpOperEntry OBJECT-TYPE SYNTAX AtmIfVccEpOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfVccEpOperTable." INDEX { atmIfIndex, atmIfVccIndex, atmIfVccEpIndex } ::= { atmIfVccEpOperTable 1 } AtmIfVccEpOperEntry ::= SEQUENCE { atmIfVccEpApplicationName RowPointer } atmIfVccEpApplicationName OBJECT-TYPE SYNTAX RowPointer ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the component name associated with the application associated with the switched VCC." ::= { atmIfVccEpOperEntry 1 } -- AtmIf/n Vpc/vpi Rp -- AtmIf/n Vcc/vpi.vci Rp -- AtmIf/n Vpt/vpi Vcc/vci Rp -- -- The RelayPoint component is used to establish a single hop of a -- Switched connection. When linked together, two Rps within a -- module, the associated connections are configured to relay ATM -- cells to one another. atmIfVccRp OBJECT IDENTIFIER ::= { atmIfVcc 10 } atmIfVccRpRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVccRpRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of atmIfVccRp components." ::= { atmIfVccRp 1 } atmIfVccRpRowStatusEntry OBJECT-TYPE SYNTAX AtmIfVccRpRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single atmIfVccRp component." INDEX { atmIfIndex, atmIfVccIndex, atmIfVccRpIndex } ::= { atmIfVccRpRowStatusTable 1 } AtmIfVccRpRowStatusEntry ::= SEQUENCE { atmIfVccRpRowStatus RowStatus, atmIfVccRpComponentName DisplayString, atmIfVccRpStorageType StorageType, atmIfVccRpIndex NonReplicated } atmIfVccRpRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of atmIfVccRp components. These components cannot be added nor deleted." ::= { atmIfVccRpRowStatusEntry 1 } atmIfVccRpComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { atmIfVccRpRowStatusEntry 2 } atmIfVccRpStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the atmIfVccRp tables." ::= { atmIfVccRpRowStatusEntry 4 } atmIfVccRpIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the atmIfVccRp tables." ::= { atmIfVccRpRowStatusEntry 10 } atmIfVccRpOperTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVccRpOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute group contains the operational attributes for the AtmRelayPoint component." ::= { atmIfVccRp 10 } atmIfVccRpOperEntry OBJECT-TYPE SYNTAX AtmIfVccRpOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfVccRpOperTable." INDEX { atmIfIndex, atmIfVccIndex, atmIfVccRpIndex } ::= { atmIfVccRpOperTable 1 } AtmIfVccRpOperEntry ::= SEQUENCE { atmIfVccRpNextHop RowPointer } atmIfVccRpNextHop OBJECT-TYPE SYNTAX RowPointer ACCESS read-only STATUS obsolete DESCRIPTION "This attribute indicates the component name of the Rp component with which this Rp component is associated." ::= { atmIfVccRpOperEntry 1 } atmIfVccRpNextHopsTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVccRpNextHopsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute indicates the component name(s) of the Rp component(s) with which this Rp component is associated. This attribute can have more than one component name only when the Vcc distributionType is pointToMultipoint and the callDirection is fromLink." ::= { atmIfVccRp 430 } atmIfVccRpNextHopsEntry OBJECT-TYPE SYNTAX AtmIfVccRpNextHopsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfVccRpNextHopsTable." INDEX { atmIfIndex, atmIfVccIndex, atmIfVccRpIndex, atmIfVccRpNextHopsValue } ::= { atmIfVccRpNextHopsTable 1 } AtmIfVccRpNextHopsEntry ::= SEQUENCE { atmIfVccRpNextHopsValue RowPointer } atmIfVccRpNextHopsValue OBJECT-TYPE SYNTAX RowPointer ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents both the value and the index for the atmIfVccRpNextHopsTable." ::= { atmIfVccRpNextHopsEntry 1 } -- AtmIf/n Vcc/vpi.vci DstPvc -- AtmIf/n Vpt/vpi Vcc/vci DstPvc -- -- This component represents the destination end of a soft PVC. atmIfVccDst OBJECT IDENTIFIER ::= { atmIfVcc 11 } atmIfVccDstRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVccDstRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of atmIfVccDst components." ::= { atmIfVccDst 1 } atmIfVccDstRowStatusEntry OBJECT-TYPE SYNTAX AtmIfVccDstRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single atmIfVccDst component." INDEX { atmIfIndex, atmIfVccIndex, atmIfVccDstIndex } ::= { atmIfVccDstRowStatusTable 1 } AtmIfVccDstRowStatusEntry ::= SEQUENCE { atmIfVccDstRowStatus RowStatus, atmIfVccDstComponentName DisplayString, atmIfVccDstStorageType StorageType, atmIfVccDstIndex NonReplicated } atmIfVccDstRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of atmIfVccDst components. These components cannot be added nor deleted." ::= { atmIfVccDstRowStatusEntry 1 } atmIfVccDstComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { atmIfVccDstRowStatusEntry 2 } atmIfVccDstStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the atmIfVccDst tables." ::= { atmIfVccDstRowStatusEntry 4 } atmIfVccDstIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the atmIfVccDst tables." ::= { atmIfVccDstRowStatusEntry 10 } atmIfVccDstOperTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVccDstOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute group contains the operational attributes for the DestinationPvc component." ::= { atmIfVccDst 10 } atmIfVccDstOperEntry OBJECT-TYPE SYNTAX AtmIfVccDstOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfVccDstOperTable." INDEX { atmIfIndex, atmIfVccIndex, atmIfVccDstIndex } ::= { atmIfVccDstOperTable 1 } AtmIfVccDstOperEntry ::= SEQUENCE { atmIfVccDstCalledAddress HexString, atmIfVccDstCallingAddress AsciiString, atmIfVccDstCallingVpiVci AsciiString } atmIfVccDstCalledAddress OBJECT-TYPE SYNTAX HexString (SIZE (20)) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute represents the called address of the soft PVC." ::= { atmIfVccDstOperEntry 3 } atmIfVccDstCallingAddress OBJECT-TYPE SYNTAX AsciiString (SIZE (7..40)) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute represents the remote address of the soft PVC. If the address in not known, then the value of this address is Unknown." ::= { atmIfVccDstOperEntry 4 } atmIfVccDstCallingVpiVci OBJECT-TYPE SYNTAX AsciiString (SIZE (7..9)) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute represents the remote VPI and VCI of the soft PVC. If the VPI and VCI values are not known, this attribute is set to Unknown." ::= { atmIfVccDstOperEntry 5 } -- AtmIf/n Vcc/vpi.vci SrcPvc -- AtmIf/n Vpt/vpi Vcc/vci SrcPvc -- -- This component represents the source end of a soft PVC. atmIfVptVccSrc OBJECT IDENTIFIER ::= { atmIfVptVcc 8 } atmIfVptVccSrcRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptVccSrcRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of atmIfVptVccSrc components." ::= { atmIfVptVccSrc 1 } atmIfVptVccSrcRowStatusEntry OBJECT-TYPE SYNTAX AtmIfVptVccSrcRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single atmIfVptVccSrc component." INDEX { atmIfIndex, atmIfVptIndex, atmIfVptVccIndex, atmIfVptVccSrcIndex } ::= { atmIfVptVccSrcRowStatusTable 1 } AtmIfVptVccSrcRowStatusEntry ::= SEQUENCE { atmIfVptVccSrcRowStatus RowStatus, atmIfVptVccSrcComponentName DisplayString, atmIfVptVccSrcStorageType StorageType, atmIfVptVccSrcIndex NonReplicated } atmIfVptVccSrcRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-write STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of atmIfVptVccSrc components. These components can be added and deleted." ::= { atmIfVptVccSrcRowStatusEntry 1 } atmIfVptVccSrcComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { atmIfVptVccSrcRowStatusEntry 2 } atmIfVptVccSrcStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the atmIfVptVccSrc tables." ::= { atmIfVptVccSrcRowStatusEntry 4 } atmIfVptVccSrcIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the atmIfVptVccSrc tables." ::= { atmIfVptVccSrcRowStatusEntry 10 } atmIfVptVccSrcProvTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptVccSrcProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute group contains the provisionable attributes of the SourcePvc component." ::= { atmIfVptVccSrc 10 } atmIfVptVccSrcProvEntry OBJECT-TYPE SYNTAX AtmIfVptVccSrcProvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfVptVccSrcProvTable." INDEX { atmIfIndex, atmIfVptIndex, atmIfVptVccIndex, atmIfVptVccSrcIndex } ::= { atmIfVptVccSrcProvTable 1 } AtmIfVptVccSrcProvEntry ::= SEQUENCE { atmIfVptVccSrcRemoteAddress HexString, atmIfVptVccSrcRemoteVpiVci IntegerSequence, atmIfVptVccSrcCallingAddress HexString, atmIfVptVccSrcCalledAddress HexString, atmIfVptVccSrcCalledVpiVci IntegerSequence } atmIfVptVccSrcRemoteAddress OBJECT-TYPE SYNTAX HexString (SIZE (20)) ACCESS read-write STATUS obsolete DESCRIPTION "This attribute represents the remote address of the soft PVC." ::= { atmIfVptVccSrcProvEntry 1 } atmIfVptVccSrcRemoteVpiVci OBJECT-TYPE SYNTAX IntegerSequence (SIZE (3..9)) ACCESS read-write STATUS obsolete DESCRIPTION "This attribute represents the remote VPI and VCI of the soft PVC." ::= { atmIfVptVccSrcProvEntry 2 } atmIfVptVccSrcCallingAddress OBJECT-TYPE SYNTAX HexString (SIZE (0..20)) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute represents the calling address of the soft PVC. If it is a null string, then the calling address is the address of the current interface (that is, where the soft PVC originates)." DEFVAL { ''H } -- "" ::= { atmIfVptVccSrcProvEntry 3 } atmIfVptVccSrcCalledAddress OBJECT-TYPE SYNTAX HexString (SIZE (20)) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute represents the called (remote) address of the soft PVC." ::= { atmIfVptVccSrcProvEntry 4 } atmIfVptVccSrcCalledVpiVci OBJECT-TYPE SYNTAX IntegerSequence (SIZE (3..10)) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute represents the remote VPI and VCI of the soft PVC." ::= { atmIfVptVccSrcProvEntry 5 } atmIfVptVccSrcOperTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptVccSrcOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute group contains the operational attributes associated with the SrcPvp or SrcPvc component." ::= { atmIfVptVccSrc 11 } atmIfVptVccSrcOperEntry OBJECT-TYPE SYNTAX AtmIfVptVccSrcOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfVptVccSrcOperTable." INDEX { atmIfIndex, atmIfVptIndex, atmIfVptVccIndex, atmIfVptVccSrcIndex } ::= { atmIfVptVccSrcOperTable 1 } AtmIfVptVccSrcOperEntry ::= SEQUENCE { atmIfVptVccSrcState INTEGER, atmIfVptVccSrcRetryCount Counter32, atmIfVptVccSrcLastFailureCauseCode Unsigned32, atmIfVptVccSrcLastFailureDiagCode AsciiString } atmIfVptVccSrcState OBJECT-TYPE SYNTAX INTEGER { active(0), inactive(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the state of the soft PVP or soft PVC." ::= { atmIfVptVccSrcOperEntry 1 } atmIfVptVccSrcRetryCount OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the number of failed attempts to set up the soft PVP or soft PVC since the last time the connection failed." ::= { atmIfVptVccSrcOperEntry 2 } atmIfVptVccSrcLastFailureCauseCode OBJECT-TYPE SYNTAX Unsigned32 (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute contains the cause code in the last transmitted signalling message that contains the CAUSE information element. The cause code is used to describe the reason for generating certain signalling messages. The default value for this attribute is set to 0." ::= { atmIfVptVccSrcOperEntry 3 } atmIfVptVccSrcLastFailureDiagCode OBJECT-TYPE SYNTAX AsciiString (SIZE (0..8)) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute contains the diagnostic code in the last transmitted signalling message. The diagnostic code is contained in the CAUSE information element and identifies an information element type or timer type. The diagnostic code is present only if a procedural error is detected by the signalling protocol. A diagnostic code is always accompanied by the cause code. If there is no failure, this attribute is set to NULL." ::= { atmIfVptVccSrcOperEntry 4 } -- AtmIf/n Vcc/vpi.vci Ep -- AtmIf/n Vpt/vpi Vcc/vci Ep -- -- The EndPoint component of the application associated with the -- VCC is used to link a switched VCC to an application that sends -- and receives frames using the connection. atmIfVptVccEp OBJECT IDENTIFIER ::= { atmIfVptVcc 9 } atmIfVptVccEpRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptVccEpRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of atmIfVptVccEp components." ::= { atmIfVptVccEp 1 } atmIfVptVccEpRowStatusEntry OBJECT-TYPE SYNTAX AtmIfVptVccEpRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single atmIfVptVccEp component." INDEX { atmIfIndex, atmIfVptIndex, atmIfVptVccIndex, atmIfVptVccEpIndex } ::= { atmIfVptVccEpRowStatusTable 1 } AtmIfVptVccEpRowStatusEntry ::= SEQUENCE { atmIfVptVccEpRowStatus RowStatus, atmIfVptVccEpComponentName DisplayString, atmIfVptVccEpStorageType StorageType, atmIfVptVccEpIndex NonReplicated } atmIfVptVccEpRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of atmIfVptVccEp components. These components cannot be added nor deleted." ::= { atmIfVptVccEpRowStatusEntry 1 } atmIfVptVccEpComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { atmIfVptVccEpRowStatusEntry 2 } atmIfVptVccEpStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the atmIfVptVccEp tables." ::= { atmIfVptVccEpRowStatusEntry 4 } atmIfVptVccEpIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the atmIfVptVccEp tables." ::= { atmIfVptVccEpRowStatusEntry 10 } atmIfVptVccEpOperTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptVccEpOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute group contains the operational attributes for the AtmEndPoint component." ::= { atmIfVptVccEp 10 } atmIfVptVccEpOperEntry OBJECT-TYPE SYNTAX AtmIfVptVccEpOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfVptVccEpOperTable." INDEX { atmIfIndex, atmIfVptIndex, atmIfVptVccIndex, atmIfVptVccEpIndex } ::= { atmIfVptVccEpOperTable 1 } AtmIfVptVccEpOperEntry ::= SEQUENCE { atmIfVptVccEpApplicationName RowPointer } atmIfVptVccEpApplicationName OBJECT-TYPE SYNTAX RowPointer ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the component name associated with the application associated with the switched VCC." ::= { atmIfVptVccEpOperEntry 1 } -- AtmIf/n Vpc/vpi Rp -- AtmIf/n Vcc/vpi.vci Rp -- AtmIf/n Vpt/vpi Vcc/vci Rp -- -- The RelayPoint component is used to establish a single hop of a -- Switched connection. When linked together, two Rps within a -- module, the associated connections are configured to relay ATM -- cells to one another. atmIfVptVccRp OBJECT IDENTIFIER ::= { atmIfVptVcc 10 } atmIfVptVccRpRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptVccRpRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of atmIfVptVccRp components." ::= { atmIfVptVccRp 1 } atmIfVptVccRpRowStatusEntry OBJECT-TYPE SYNTAX AtmIfVptVccRpRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single atmIfVptVccRp component." INDEX { atmIfIndex, atmIfVptIndex, atmIfVptVccIndex, atmIfVptVccRpIndex } ::= { atmIfVptVccRpRowStatusTable 1 } AtmIfVptVccRpRowStatusEntry ::= SEQUENCE { atmIfVptVccRpRowStatus RowStatus, atmIfVptVccRpComponentName DisplayString, atmIfVptVccRpStorageType StorageType, atmIfVptVccRpIndex NonReplicated } atmIfVptVccRpRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of atmIfVptVccRp components. These components cannot be added nor deleted." ::= { atmIfVptVccRpRowStatusEntry 1 } atmIfVptVccRpComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { atmIfVptVccRpRowStatusEntry 2 } atmIfVptVccRpStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the atmIfVptVccRp tables." ::= { atmIfVptVccRpRowStatusEntry 4 } atmIfVptVccRpIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the atmIfVptVccRp tables." ::= { atmIfVptVccRpRowStatusEntry 10 } atmIfVptVccRpOperTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptVccRpOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute group contains the operational attributes for the AtmRelayPoint component." ::= { atmIfVptVccRp 10 } atmIfVptVccRpOperEntry OBJECT-TYPE SYNTAX AtmIfVptVccRpOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfVptVccRpOperTable." INDEX { atmIfIndex, atmIfVptIndex, atmIfVptVccIndex, atmIfVptVccRpIndex } ::= { atmIfVptVccRpOperTable 1 } AtmIfVptVccRpOperEntry ::= SEQUENCE { atmIfVptVccRpNextHop RowPointer } atmIfVptVccRpNextHop OBJECT-TYPE SYNTAX RowPointer ACCESS read-only STATUS obsolete DESCRIPTION "This attribute indicates the component name of the Rp component with which this Rp component is associated." ::= { atmIfVptVccRpOperEntry 1 } atmIfVptVccRpNextHopsTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptVccRpNextHopsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute indicates the component name(s) of the Rp component(s) with which this Rp component is associated. This attribute can have more than one component name only when the Vcc distributionType is pointToMultipoint and the callDirection is fromLink." ::= { atmIfVptVccRp 430 } atmIfVptVccRpNextHopsEntry OBJECT-TYPE SYNTAX AtmIfVptVccRpNextHopsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfVptVccRpNextHopsTable." INDEX { atmIfIndex, atmIfVptIndex, atmIfVptVccIndex, atmIfVptVccRpIndex, atmIfVptVccRpNextHopsValue } ::= { atmIfVptVccRpNextHopsTable 1 } AtmIfVptVccRpNextHopsEntry ::= SEQUENCE { atmIfVptVccRpNextHopsValue RowPointer } atmIfVptVccRpNextHopsValue OBJECT-TYPE SYNTAX RowPointer ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents both the value and the index for the atmIfVptVccRpNextHopsTable." ::= { atmIfVptVccRpNextHopsEntry 1 } -- AtmIf/n Vcc/vpi.vci DstPvc -- AtmIf/n Vpt/vpi Vcc/vci DstPvc -- -- This component represents the destination end of a soft PVC. atmIfVptVccDst OBJECT IDENTIFIER ::= { atmIfVptVcc 11 } atmIfVptVccDstRowStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptVccDstRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry controls the addition and deletion of atmIfVptVccDst components." ::= { atmIfVptVccDst 1 } atmIfVptVccDstRowStatusEntry OBJECT-TYPE SYNTAX AtmIfVptVccDstRowStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single entry in the table represents a single atmIfVptVccDst component." INDEX { atmIfIndex, atmIfVptIndex, atmIfVptVccIndex, atmIfVptVccDstIndex } ::= { atmIfVptVccDstRowStatusTable 1 } AtmIfVptVccDstRowStatusEntry ::= SEQUENCE { atmIfVptVccDstRowStatus RowStatus, atmIfVptVccDstComponentName DisplayString, atmIfVptVccDstStorageType StorageType, atmIfVptVccDstIndex NonReplicated } atmIfVptVccDstRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable is used as the basis for SNMP naming of atmIfVptVccDst components. These components cannot be added nor deleted." ::= { atmIfVptVccDstRowStatusEntry 1 } atmIfVptVccDstComponentName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable provides the component's string name for use with the ASCII Console Interface" ::= { atmIfVptVccDstRowStatusEntry 2 } atmIfVptVccDstStorageType OBJECT-TYPE SYNTAX StorageType ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the storage type value for the atmIfVptVccDst tables." ::= { atmIfVptVccDstRowStatusEntry 4 } atmIfVptVccDstIndex OBJECT-TYPE SYNTAX NonReplicated ACCESS not-accessible STATUS mandatory DESCRIPTION "This variable represents the index for the atmIfVptVccDst tables." ::= { atmIfVptVccDstRowStatusEntry 10 } atmIfVptVccDstOperTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptVccDstOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This attribute group contains the operational attributes for the DestinationPvc component." ::= { atmIfVptVccDst 10 } atmIfVptVccDstOperEntry OBJECT-TYPE SYNTAX AtmIfVptVccDstOperEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atmIfVptVccDstOperTable." INDEX { atmIfIndex, atmIfVptIndex, atmIfVptVccIndex, atmIfVptVccDstIndex } ::= { atmIfVptVccDstOperTable 1 } AtmIfVptVccDstOperEntry ::= SEQUENCE { atmIfVptVccDstCalledAddress HexString, atmIfVptVccDstCallingAddress AsciiString, atmIfVptVccDstCallingVpiVci AsciiString } atmIfVptVccDstCalledAddress OBJECT-TYPE SYNTAX HexString (SIZE (20)) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute represents the called address of the soft PVC." ::= { atmIfVptVccDstOperEntry 3 } atmIfVptVccDstCallingAddress OBJECT-TYPE SYNTAX AsciiString (SIZE (7..40)) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute represents the remote address of the soft PVC. If the address in not known, then the value of this address is Unknown." ::= { atmIfVptVccDstOperEntry 4 } atmIfVptVccDstCallingVpiVci OBJECT-TYPE SYNTAX AsciiString (SIZE (7..9)) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute represents the remote VPI and VCI of the soft PVC. If the VPI and VCI values are not known, this attribute is set to Unknown." ::= { atmIfVptVccDstOperEntry 5 } -- -- Version and Compliance statements -- -- Object-Group Statement: -- A list of all current accessible leaf objects. -- OBJECTS { atmIfVptVccSrcLastFailureDiagCode, -- atmIfVccRpNextHopsValue, -- aRtgPnniCfgNodeDefSAddrScope, -- aRtgPnniCallsRerouted, -- atmIfVptVccDstRowStatus, -- aRtgPnniRfDestinationAddress, -- atmIfVpcRpNextHopsValue, -- aRtgPnniRfRowStatus, -- atmIfVptVccRpComponentName, -- atmCRDnaStorageType, -- aRtgPnniTopNodeLinkRowStatus, -- aRtgPnniTopNodeAddrComponentName, -- aRtgPnniTopNodeComponentName, -- aRtgPnniCfgNodeRowStatus, -- aRtgPnniPortStorageType, -- atmIfVpcRpComponentName, -- atmIfVpcSrcLastFailureDiagCode, -- aRtgPnniTopNodeLinkStorageType, -- aRtgPnniNodeAddressPrefix, -- atmIfVpcSrcCallingAddress, -- aRtgPnniCfgNodeNodeId, -- atmIfVpcSrcCalledVpi, -- aRtgPnniPeerDelayedAckInterval, -- aRtgPnniCfgNodeNodeAddress, -- aRtgPnniCfgNodeDefSAddrComponentName, -- atmIfVpcDstCallingAddress, -- aRtgPnniCfgNodeNbrPtseAcksRx, -- atmIfVpcDstComponentName, -- aRtgPnniPtseHoldDown, -- aRtgPnniTopStorageType, -- aRtgRoutingAttempts, -- aRtgPnniPtseLifetimeFactor, -- aRtgPnniCfgNodeNbrStorageType, -- atmIfVccSrcCallingAddress, -- aRtgPnniRfBwdQosClass, -- atmCRDnaRowStatus, -- aRtgPnniCfgNodeNbrPtseReqTx, -- atmIfVpcDstCalledAddress, -- aRtgDnaComponentName, -- aRtgPnniStorageType, -- aRtgDnaDestInfoType, -- aRtgPnniPortRowStatus, -- aRtgPnniCfgNodeSAddrScope, -- atmIfVptVccSrcState, -- aRtgPnniRfClippingBbc, -- aRtgPnniRoutingAttempts, -- aRtgPnniDefaultScope, -- atmCRDnaComponentName, -- atmIfVccDstCalledAddress, -- atmIfVptVccSrcRowStatus, -- aRtgPnniRfBqpValue, -- atmIfVptVccEpStorageType, -- aRtgPnniRfRxTdpValue, -- aRtgPnniRfBestEffort, -- aRtgPnniCfgNodePeerGroupId, -- aRtgPnniCfgNodeNbrPtspRx, -- aRtgPnniOverrideDelay, -- aRtgPnniCfgNodeDefSAddrState, -- atmIfVptVccSrcRetryCount, -- atmIfVccSrcCalledVpiVci, -- aRtgPnniCfgNodeOpNodeId, -- atmIfVccDstRowStatus, -- atmIfVptVccRpStorageType, -- aRtgPnniRowStatus, -- atmIfVccDstStorageType, -- aRtgPnniCfgNodeNbrPtseReqRx, -- aRtgPnniTopNodeAddrStorageType, -- aRtgPnniTopNodeStorageType, -- atmIfVptVccEpRowStatus, -- aRtgPnniTopNodeLinkRemotePortId, -- atmIfVccSrcComponentName, -- aRtgPnniPortStdComponentName, -- aRtgPnniCfgNodeSAddrSuppress, -- aRtgDnaDestInfoComponentName, -- atmIfVpcSrcComponentName, -- aRtgPnniCfgNodeNbrPeerState, -- atmIfVpcDstStorageType, -- atmIfVccDstCallingAddress, -- atmIfVpcSrcState, -- aRtgPnniRequestRxmtInterval, -- aRtgPnniCfgNodeNumRccs, -- atmIfVptVccRpRowStatus, -- aRtgPnniCfgNodeOpPeerGroupId, -- aRtgPnniCfgNodeNbrDbSummariesTx, -- aRtgPnniCfgNodeDefSAddrStorageType, -- atmIfVpcDstCallingVpi, -- aRtgPnniCfgNodeNbrBadPtseAckRx, -- aRtgPnniCfgNodeDefSAddrAddress, -- aRtgPnniRfOptimizationMetric, -- atmCRComponentName, -- aRtgPnniAvcrMt, -- atmIfVpcSrcCalledAddress, -- aRtgPnniCfgNodeCurrentLeadershipPriority, -- aRtgPnniPglInitTime, -- atmIfVccSrcLastFailureDiagCode, -- aRtgPnniTopNodeAddrRowStatus, -- aRtgDnaStorageType, -- aRtgPnniRfTxTrafficDescType, -- aRtgPnniCfgNodeNbrPtseTx, -- aRtgPnniCfgNodeNbrRowStatus, -- atmIfVccSrcState, -- aRtgPnniCfgNodeSAddrComponentName, -- aRtgPnniRfTransferCapabilityBbc, -- atmIfVpcDstRowStatus, -- aRtgPnniCfgNodeNbrRccListValue, -- atmIfVccSrcStorageType, -- aRtgPnniTopActiveParentNodeId, -- aRtgPnniRfMaxRoutes, -- atmIfVccRpComponentName, -- atmIfVccSrcRowStatus, -- aRtgPnniCfgNodeDefSAddrRowStatus, -- aRtgPnniHelloInterval, -- aRtgPnniCfgNodeNbrDbSummariesRx, -- aRtgPnniTopNodeRowStatus, -- aRtgPnniRfTxTdpValue, -- aRtgPnniCfgNodeNbrBadPtseReqRx, -- aRtgPnniHelloInactivityFactor, -- atmIfVptVccEpApplicationName, -- aRtgPnniCfgNodeNbrPtseRx, -- atmIfVptVccDstCallingVpiVci, -- aRtgPnniCfgNodeNbrPtspTx, -- aRtgPnniPtseRefreshInterval, -- aRtgPnniRestrictTransit, -- aRtgDnaRowStatus, -- aRtgPnniMaxReroutesOnCrankback, -- atmIfVptVccSrcStorageType, -- atmIfVptVccSrcCallingAddress, -- aRtgPnniFailedRoutingAttempts, -- aRtgPnniRfRxTrafficDescType, -- aRtgPnniCfgNodeNumNeighbors, -- aRtgPnniRfComponentName, -- aRtgDnaDestInfoStorageType, -- atmIfVpcSrcStorageType, -- aRtgPnniTopNodeLinkComponentName, -- aRtgPnniCfgNodeSAddrState, -- aRtgPnniCfgNodeComponentName, -- atmIfVccDstComponentName, -- aRtgPnniTopologyMemoryExhaustion, -- atmIfVptVccDstCalledAddress, -- aRtgPnniTopPreferredPglNodeId, -- atmIfVpcSrcRowStatus, -- atmIfVptVccRpNextHopsValue, -- atmIfVccEpStorageType, -- aRtgPnniRfBearerClassBbc, -- aRtgDnaDestInfoReachability, -- atmIfVccSrcLastFailureCauseCode, -- aRtgPnniCfgNodeNbrBadPtseRx, -- aRtgPnniAvcrPm, -- aRtgPnniTopNodeAddrScope, -- aRtgPnniTopRowStatus, -- atmIfVptVccDstComponentName, -- atmIfVptVccSrcCalledVpiVci, -- atmIfVccSrcRetryCount, -- aRtgDnaDestInfoRowStatus, -- aRtgPnniCfgNodeSAddrStorageType, -- atmCRStorageType, -- aRtgPnniCfgNodeNbrBadDbSummariesRx, -- atmIfVpcRpStorageType, -- aRtgPnniReElectionInterval, -- aRtgPnniOptMetricValue, -- aRtgPnniPortComponentName, -- atmIfVpcSrcRetryCount, -- atmIfVccRpStorageType, -- atmIfVptVccEpComponentName, -- aRtgPnniCfgNodePglElectionState, -- atmIfVccDstCallingVpiVci, -- atmIfVptVccSrcCalledAddress, -- atmIfVptVccDstStorageType, -- atmCRRowStatus, -- aRtgPnniRfFwdQosClass, -- aRtgComponentName, -- aRtgRowStatus, -- aRtgPnniTopPtsesInDatabase, -- atmIfVccRpRowStatus, -- atmIfVptVccSrcComponentName, -- aRtgPnniCfgNodeNbrPtseAcksTx, -- aRtgPnniTopComponentName, -- aRtgPnniCfgNodeNbrComponentName, -- atmIfVptVccDstCallingAddress, -- atmIfVccEpRowStatus, -- aRtgPnniCfgNodeSAddrRowStatus, -- atmIfVptVccSrcLastFailureCauseCode, -- aRtgFailedRoutingAttempts, -- aRtgPnniRfStorageType, -- aRtgPnniComponentName, -- aRtgDnaDestInfoStdComponentName, -- aRtgPnniTopPglNodeId, -- atmIfVpcSrcLastFailureCauseCode, -- atmIfVccSrcCalledAddress, -- aRtgPnniCfgNodeStorageType, -- aRtgPnniRfFqpValue, -- atmIfVccEpApplicationName, -- aRtgPnniTopNodeLinkRemoteNodeId, -- aRtgStorageType, -- aRtgPnniCfgNodeNbrBadPtspRx, -- atmIfVpcRpRowStatus, -- aRtgPnniRfAtmServiceCategory, -- aRtgDnaDestInfoScope, -- atmIfVccEpComponentName, -- aRtgPnniHelloHoldDown, -- aRtgPnniDomain } -- STATUS mandatory -- DESCRIPTION -- "A list of all current accessible leaf objects." atmNetworkingGroup OBJECT IDENTIFIER ::= { atmNetworkingMIB 1 } atmNetworkingGroupBE OBJECT IDENTIFIER ::= { atmNetworkingGroup 5 } atmNetworkingGroupBE01 OBJECT IDENTIFIER ::= { atmNetworkingGroupBE 2 } atmNetworkingGroupBE01A OBJECT IDENTIFIER ::= { atmNetworkingGroupBE01 2 } -- Agent-Capabilities Statement: -- PRODUCT-RELEASE "Passport Release 7.0 AtmNetworking." -- STATUS mandatory -- DESCRIPTION "AtmNetworking MIB: MIB Version BE01A, -- Software Version BG00S4C." -- SUPPORTS Nortel-Magellan-Passport-AtmNetworkingMIB -- INCLUDES { atmNetworkingGroupBE01A } atmNetworkingCapabilities OBJECT IDENTIFIER ::= { atmNetworkingMIB 3 } atmNetworkingCapabilitiesBE OBJECT IDENTIFIER ::= { atmNetworkingCapabilities 5 } atmNetworkingCapabilitiesBE01 OBJECT IDENTIFIER ::= { atmNetworkingCapabilitiesBE 2 } atmNetworkingCapabilitiesBE01A OBJECT IDENTIFIER ::= { atmNetworkingCapabilitiesBE01 2 } END