-- -- Juniper Enterprise Specific ATM MIB. -- -- Copyright (c) 2001-2004, Juniper Networks, Inc. -- All rights reserved. -- -- The contents of this document are subject to change without notice. -- JUNIPER-ATM-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Counter32, Counter64 FROM SNMPv2-SMI TEXTUAL-CONVENTION FROM SNMPv2-TC InetAddressIPv4, InetAddressIPv6 FROM INET-ADDRESS-MIB ifIndex FROM IF-MIB atmInterfaceConfEntry, atmVclEntry, atmVplEntry FROM ATM-MIB jnxMibs FROM JUNIPER-SMI; jnxAtm MODULE-IDENTITY LAST-UPDATED "200312040000Z" -- Thu Dec 4 2003 UTC ORGANIZATION "Juniper Networks, Inc." CONTACT-INFO "Juniper Technical Assistance Center Juniper Networks, Inc. 1194 N. Mathilda Avenue Sunnyvale, CA 94089 E-mail: support@juniper.net" DESCRIPTION "The Juniper enterprise MIB for ATM interfaces and VCs" REVISION "200401060000Z" -- Tue Jan 06 2004 DESCRIPTION "The following new objects were added: - jnxAtmVCOutOAMF5AISCells (jnxAtmVCTable). - jnxAtmTrunkOutOAMF4AISCells (jnxAtmTrunkTable)." REVISION "200312040000Z" -- Thu Dec 4 2003 UTC DESCRIPTION "New object 'jnxAtmIfL2CircuitMode' added to jnxAtmIfTable." REVISION "200309170000Z" -- Wed Sept 17 2003 DESCRIPTION "New table 'jnxAtmTrunkTable' added." REVISION "200207040000Z" -- 4th July 2002 DESCRIPTION "New table 'jnxAtmVpTable' added." REVISION "200201230000Z" -- 23 Jan 2002 DESCRIPTION "Renamed atmTcc as atmTccVcMux. atmTccSnap encapsulation added." REVISION "200107080000Z" -- 8 July, 2001 DESCRIPTION "Initial Version" ::= { jnxMibs 10 } JnxAtmFlags ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Flags related to the VC or Trunk." SYNTAX BITS { inverseArpEnabled(0), ilmiEnabled(1), oamEnabled(2), shapingEnabled(3), passiveOam(4), multicast(5), closed(6), down(7), active(8), cosEnabled(9) } -- The ATM Physical Interface Table -- -- This table augments atmInterfaceConfTable defined in ATM-MIB. -- jnxAtmIfTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxAtmIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains config and stats parameters, one entry per physical interface (ATM port)." ::= { jnxAtm 1 } jnxAtmIfEntry OBJECT-TYPE SYNTAX JnxAtmIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry contains additional ATM interface config and stats objects, not covered in standard mibs. Each entry is an extension of atmInterfaceConfEntry defined in ATM-MIB." AUGMENTS { atmInterfaceConfEntry } ::= { jnxAtmIfTable 1 } JnxAtmIfEntry ::= SEQUENCE { -- Config Info jnxAtmIfPortType INTEGER, jnxAtmIfEncaps INTEGER, jnxAtmIfLpBackInfo INTEGER, jnxAtmIfScrambleEnable INTEGER, -- Cell Stats jnxAtmIfTxCellCount Counter64, jnxAtmIfRxCellCount Counter64, jnxAtmIfTxIdleCellCount Counter64, jnxAtmIfUncorrHCSErrs Counter64, jnxAtmIfCorrHCSErrs Counter64, jnxAtmIfTxCellFIFOOverRuns Counter64, jnxAtmIfRxCellFIFOOverRuns Counter64, jnxAtmIfRxCellFIFOUnderRuns Counter64, jnxAtmIfInInvalidVCCells Counter64, jnxAtmIfInNoBufferOAMCells Counter64, -- AAL5 Packet stats jnxAtmIfInNoBufDropPkts Counter64, jnxAtmIfOutVCQueueDrops Counter64, jnxAtmIfInBadCrcs Counter64, jnxAtmIfInLenErrPkts Counter64, jnxAtmIfInTimeoutPkts Counter64, -- Misc Info jnxAtmIfL2CircuitMode INTEGER } jnxAtmIfPortType OBJECT-TYPE SYNTAX INTEGER { other(1), oc3(2), oc12(3), t3(4), e3(5), oc48(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The physical port type." ::= { jnxAtmIfEntry 1 } jnxAtmIfEncaps OBJECT-TYPE SYNTAX INTEGER { other(1), atmPvc(2), atmCccCellRelay(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "ATM physical link layer encapsulation." DEFVAL { atmPvc } ::= { jnxAtmIfEntry 2 } jnxAtmIfLpBackInfo OBJECT-TYPE SYNTAX INTEGER { noLoopBack(1), localLoopBack(2), remoteLoopBack(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Loop back config and type." ::= { jnxAtmIfEntry 3 } jnxAtmIfScrambleEnable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Shows whether scrambling is enabled or disabled" DEFVAL { disabled } ::= { jnxAtmIfEntry 4 } -- Cell Stats jnxAtmIfTxCellCount OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ATM cells transmitted by the interface. Includes Idle cells transmitted." ::= { jnxAtmIfEntry 5 } jnxAtmIfRxCellCount OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ATM cells received by the interface. Excludes Idle cells received." ::= { jnxAtmIfEntry 6 } jnxAtmIfTxIdleCellCount OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of idle cells sent by the port. When the ATM interface has nothing to send, it sends idle cells to fill the time slot." ::= { jnxAtmIfEntry 7 } jnxAtmIfUncorrHCSErrs OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of uncorrectable cell Header Check Sequence (HCS) Errors that occurred." ::= { jnxAtmIfEntry 8 } jnxAtmIfCorrHCSErrs OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of correctable cell Header Check Sequence (HCS) Errors that occurred." ::= { jnxAtmIfEntry 9 } jnxAtmIfTxCellFIFOOverRuns OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of overruns in the Transmit FIFO." ::= { jnxAtmIfEntry 10 } jnxAtmIfRxCellFIFOOverRuns OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of overruns in the Receive FIFO." ::= { jnxAtmIfEntry 11 } jnxAtmIfRxCellFIFOUnderRuns OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of underruns in the receive FIFO." ::= { jnxAtmIfEntry 12 } jnxAtmIfInInvalidVCCells OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Cells that arrived for non existent VC." ::= { jnxAtmIfEntry 13 } jnxAtmIfInNoBufferOAMCells OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of received OAM cells or raw cells dropped because no buffers were available to handle them." ::= { jnxAtmIfEntry 14 } -- AAL5 Pkt Stats jnxAtmIfInNoBufDropPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of AAL5 packets dropped because there was no enough buffer to handle them." ::= { jnxAtmIfEntry 15 } jnxAtmIfOutVCQueueDrops OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets dropped because of queue limits on each VC." ::= { jnxAtmIfEntry 16 } jnxAtmIfInBadCrcs OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of incoming CRC errors." ::= { jnxAtmIfEntry 17 } jnxAtmIfInLenErrPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of AAL5 packets dropped because their length was incorrect." ::= { jnxAtmIfEntry 18 } jnxAtmIfInTimeoutPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of AAL5 packets dropped because of reassembly timeout." ::= { jnxAtmIfEntry 19 } jnxAtmIfL2CircuitMode OBJECT-TYPE SYNTAX INTEGER { notApplicable(1), none(2), aal5(3), cell(4), uniTrunk(5), nniTrunk(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The layer 2 circuit mode of this Atm interface. Note, this applies only to interfaces on AtmII pics." ::= { jnxAtmIfEntry 20 } -- -- Juniper ATM Virtual Circuit Table -- -- This table augments the atmVclTable defined in ATM-MIB. -- jnxAtmVCTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxAtmVCEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of all p2p/p2mp/multicast VC entries." ::= { jnxAtm 2 } jnxAtmVCEntry OBJECT-TYPE SYNTAX JnxAtmVCEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Special Cases: - No traffic Stats for multicast VCs. (0 by default). - Multipoint Destination IP Address for a p2p vc is invalid (0.0.0.0 by default). - When the encapsulation type for the logical interface (to which VC belongs) is 'atmCccCellRelay', only Generic VC Info is valid. - If OAM is disabled (indicated in jnxAtmVCFlags), then all the OAM config & F5 stats info is invalid. (zeroed by default)." AUGMENTS { atmVclEntry } ::= { jnxAtmVCTable 1 } JnxAtmVCEntry ::= SEQUENCE { -- Generic VC Info jnxAtmVCConnType INTEGER, jnxAtmVCEncapsulation INTEGER, jnxAtmVCMpDestIPv4Addr InetAddressIPv4, jnxAtmVCMpDestIPv6Addr InetAddressIPv6, jnxAtmVCFlags JnxAtmFlags, jnxAtmVCTotalDownTime Integer32, -- Traffic stats jnxAtmVCInBytes Counter64, jnxAtmVCOutBytes Counter64, jnxAtmVCInPkts Counter64, jnxAtmVCOutPkts Counter64, jnxAtmVCTailQueuePktDrops Counter64, -- OAM Config jnxAtmVCOAMPeriod Integer32, jnxAtmVCOAMUpCellCount Integer32, jnxAtmVCOAMDownCellCount Integer32, -- OAM F5 Cell Stats jnxAtmVCInOAMF5LoopCells Counter32, jnxAtmVCOutOAMF5LoopCells Counter32, jnxAtmVCInOAMF5RDICells Counter32, jnxAtmVCOutOAMF5RDICells Counter32, jnxAtmVCInOAMF5AISCells Counter32, jnxAtmVCOutOAMF5AISCells Counter32 } jnxAtmVCConnType OBJECT-TYPE SYNTAX INTEGER { other(1), p2p(2), -- point-to-point p2mp(3), -- point-to-multipoint multicast(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of connection. The type 'other' means vc type is unknown or is not one of the other types." ::= { jnxAtmVCEntry 1 } jnxAtmVCEncapsulation OBJECT-TYPE SYNTAX INTEGER { other(1), atmCccCellRelay(2), atmCccVcMux(3), atmCiscoNlpid(4), atmNlpid(5), atmSnap(6), atmVcMux(7), atmTccVcMux(8), atmTccSnap(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "The atm encapsulation type associated with the VC. atmCccCellRelay : ATM Cell Relay for CCC atmCccVcMux : ATM VC for CCC atmCiscoNlpid : Cisco-compatible ATM NLPID encapsulation atmNlpid : ATM NLPID encapsulation atmSnap : ATM LLC/SNAP encapsulation atmVcMux : ATM VC multiplexing atmTccVcMux : TCC (Translational Cross Connection) over ATM VC MUX encapsulation atmTccSnap : TCC (Translational Cross Connection) over ATM LLC/SNAP encapsulation" ::= { jnxAtmVCEntry 2} jnxAtmVCMpDestIPv4Addr OBJECT-TYPE SYNTAX InetAddressIPv4 MAX-ACCESS read-only STATUS current DESCRIPTION "This object is meaningful only if jnxAtmVCConnType value is 'p2mp' (point-to-multipoint). For a p2mp VC, it's the multipoint destination IPv4 address. When the VC connection type is other than p2mp OR when the multipoint destination address type is of IPv6, this object returns 0.0.0.0 by default." ::= { jnxAtmVCEntry 3 } jnxAtmVCMpDestIPv6Addr OBJECT-TYPE SYNTAX InetAddressIPv6 MAX-ACCESS read-only STATUS current DESCRIPTION "This object is meaningful only if jnxAtmVCConnType value is 'p2mp' (point-to-multipoint). For a p2mp VC, it's the multipoint destination IPv6 address. When the VC connection type is other than p2mp OR when the multipoint destination address type is of IPv4, this object returns all the bytes of addr filled with 0." ::= { jnxAtmVCEntry 4 } jnxAtmVCFlags OBJECT-TYPE SYNTAX JnxAtmFlags MAX-ACCESS read-only STATUS current DESCRIPTION "Flags related to the VC." ::= { jnxAtmVCEntry 5 } jnxAtmVCTotalDownTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total VC down time in seconds ever since the system rebooted." ::= { jnxAtmVCEntry 6 } -- Traffic Stats jnxAtmVCInBytes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of bytes received on the VC." ::= { jnxAtmVCEntry 7 } jnxAtmVCOutBytes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of bytes sent out on the VC." ::= { jnxAtmVCEntry 8 } jnxAtmVCInPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets received on the VC." ::= { jnxAtmVCEntry 9 } jnxAtmVCOutPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets sent out on the VC." ::= { jnxAtmVCEntry 10 } jnxAtmVCTailQueuePktDrops OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets dropped due to bandwidth constraints. Indicates that packets were queued to send out at a rate faster than allowed." ::= { jnxAtmVCEntry 11 } -- OAM Config jnxAtmVCOAMPeriod OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This time interval indicates how often the F5 cells are sent to know the status of the VC." ::= { jnxAtmVCEntry 12 } jnxAtmVCOAMUpCellCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum number of loopback cells to be received to declare that the VC is up." ::= { jnxAtmVCEntry 13 } jnxAtmVCOAMDownCellCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum number of loopback cells to be received to declare that the VC is down. This object would have zero value if OAM is not enabled. (indicated in jnxAtmVCFlags)" ::= { jnxAtmVCEntry 14 } -- OAM F5 Stats jnxAtmVCInOAMF5LoopCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of OAM F5 loopback cells received. This object would have zero value if OAM (as indicated in jnxAtmVCFlags) is not enabled." ::= { jnxAtmVCEntry 15 } jnxAtmVCOutOAMF5LoopCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of OAM F5 loopback cells sent. This object would have zero value if OAM (as indicated in jnxAtmVCFlags) is not enabled." ::= { jnxAtmVCEntry 16 } jnxAtmVCInOAMF5RDICells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of OAM F5 cells received, with RDI(Remote Defect Indication) bit set. This object would have zero value if OAM (as indicated in jnxAtmVCFlags) is not enabled." ::= { jnxAtmVCEntry 17 } jnxAtmVCOutOAMF5RDICells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of OAM F5 cells transmitted, with RDI(Remote Defect Indication) bit set. This object would have zero value if OAM (as indicated in jnxAtmVCFlags) is not enabled." ::= { jnxAtmVCEntry 18 } jnxAtmVCInOAMF5AISCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of OAM F5 cells received, with AIS(Alarm Indication Signal) bit set. This object would have zero value if OAM (as indicated in jnxAtmVCFlags) is not enabled." ::= { jnxAtmVCEntry 19 } jnxAtmVCOutOAMF5AISCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of OAM F5 cells transmitted, with AIS (Alarm Indication Signal) bit set. This object would have zero value if OAM (as indicated in jnxAtmVCFlags) is not enabled." ::= { jnxAtmVCEntry 20 } -- -- Juniper ATM VP (Virtual Path) table -- -- This table augments the atmVplTable defined in ATM-MIB. -- jnxAtmVpTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxAtmVpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of ATM VPs. This table augments atmVplTable defined in standard ATM mib." ::= { jnxAtm 3 } jnxAtmVpEntry OBJECT-TYPE SYNTAX JnxAtmVpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry represents config, status and statistics info related to an ATM VP configured. This entry augments the atmVplEntry defined in standard ATM mib (RFC 2515). So ifIndex and VPI are the indices to this table. Caveats: - Traffic stats are available per VP tunnel, only if shaping is configured on the VP. Object 'jnxAtmVpFlags' can be used to determine if shaping is enabled. - When no OAM is configured, OAM config and OAM stat objects' values are invalid (zero by default). Object 'jnxAtmVpFlags' contains info on whether OAM is configured or not. - For atm-1 VPs, the only valid object is jnxAtmVpFlags." AUGMENTS { atmVplEntry } ::= { jnxAtmVpTable 1 } JnxAtmVpEntry ::= SEQUENCE { -- VP Generic Info jnxAtmVpFlags BITS, jnxAtmVpTotalDownTime Integer32, -- VP OAM config jnxAtmVpOamPeriod Integer32, jnxAtmVpOamUpCellCount Integer32, jnxAtmVpOamDownCellCount Integer32, -- VP Traffic Stats jnxAtmVpInBytes Counter64, jnxAtmVpOutBytes Counter64, jnxAtmVpInPkts Counter64, jnxAtmVpOutPkts Counter64, -- VP OAM F4 Cell Stats jnxAtmVpInOamF4Cells Counter32, jnxAtmVpOutOamF4Cells Counter32, jnxAtmVpInOamF4LoopCells Counter32, jnxAtmVpOutOamF4LoopCells Counter32, jnxAtmVpInOamF4RdiCells Counter32, jnxAtmVpOutOamF4RdiCells Counter32, jnxAtmVpInOamF4AisCells Counter32 } -- VP Generic Info jnxAtmVpFlags OBJECT-TYPE SYNTAX BITS { active(0), down(1), oamEnabled(2), shapingEnabled(3), passiveOam(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The flags associated with this VP." ::= { jnxAtmVpEntry 1 } jnxAtmVpTotalDownTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total VP downtime in seconds, ever since the system rebooted." ::= { jnxAtmVpEntry 2 } -- VP OAM config jnxAtmVpOamPeriod OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This time interval indicates how often the OAM F4 cells are sent to determine the status of the VP. The value of this object is zero when OAM is not enabled on the VP. Object 'jnxAtmVpFlags' can be used to determine if OAM is enabled." ::= { jnxAtmVpEntry 3 } jnxAtmVpOamUpCellCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum number of consecutive loopback cells to be received to declare that the VP is up. The value of this object is zero when OAM is not enabled on the VP. Object 'jnxAtmVpFlags' can be used to determine if OAM is enabled." ::= { jnxAtmVpEntry 4 } jnxAtmVpOamDownCellCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum number of consecutive loopback cells to be received to declare that the VP is down. The value of this object is zero when OAM is not enabled on the VP. Object 'jnxAtmVpFlags' can be used to determine if OAM is enabled." ::= { jnxAtmVpEntry 5 } -- VP Traffic stats jnxAtmVpInBytes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of bytes received on the VP." ::= { jnxAtmVpEntry 6 } jnxAtmVpOutBytes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of bytes sent out on the VP." ::= { jnxAtmVpEntry 7 } jnxAtmVpInPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets received on the VP." ::= { jnxAtmVpEntry 8 } jnxAtmVpOutPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets sent out on the VP." ::= { jnxAtmVpEntry 9 } -- VP OAM F4 stats jnxAtmVpInOamF4Cells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of OAM F4 cells received on the VP." ::= { jnxAtmVpEntry 10 } jnxAtmVpOutOamF4Cells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of OAM F4 cells transmitted on the VP." ::= { jnxAtmVpEntry 11 } jnxAtmVpInOamF4LoopCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of OAM F4 loopback cells received on the VP." ::= { jnxAtmVpEntry 12 } jnxAtmVpOutOamF4LoopCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of OAM F4 cells transmitted on the VP." ::= { jnxAtmVpEntry 13 } jnxAtmVpInOamF4RdiCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of OAM F4 RDI cells received on the VP." ::= { jnxAtmVpEntry 14 } jnxAtmVpOutOamF4RdiCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of OAM F4 RDI cells transmitted on the VP." ::= { jnxAtmVpEntry 15 } jnxAtmVpInOamF4AisCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of OAM F4 AIS cells received on the VP." ::= { jnxAtmVpEntry 16 } -- -- Juniper ATM Trunk Table -- jnxAtmTrunkTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxAtmTrunkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of all ATM Trunk entries." ::= { jnxAtm 4 } jnxAtmTrunkEntry OBJECT-TYPE SYNTAX JnxAtmTrunkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Special Cases: - When the encapsulation type for the logical interface (to which Trunk belongs) is 'atmCccCellRelay', only Generic Trunk Info is valid." INDEX { ifIndex } ::= { jnxAtmTrunkTable 1 } JnxAtmTrunkEntry ::= SEQUENCE { jnxAtmTrunkId Integer32, -- Generic Trunk Info jnxAtmTrunkConnType INTEGER, jnxAtmTrunkEncapsulation INTEGER, jnxAtmTrunkFlags JnxAtmFlags, jnxAtmTrunkTotalDownTime Integer32, -- Traffic stats jnxAtmTrunkInBytes Counter64, jnxAtmTrunkOutBytes Counter64, jnxAtmTrunkInPkts Counter64, jnxAtmTrunkOutPkts Counter64, jnxAtmTrunkTailQueuePktDrops Counter64, -- OAM F4 Cell Stats jnxAtmTrunkInOAMF4AISCells Counter32, jnxAtmTrunkOutOAMF4AISCells Counter32 } jnxAtmTrunkId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The identifier for this ATM Trunk." ::= { jnxAtmTrunkEntry 1 } jnxAtmTrunkConnType OBJECT-TYPE SYNTAX INTEGER { other(1), p2p(2) -- point-to-point } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of connection. The type 'other' means trunk type is unknown or is not one of the other types." ::= { jnxAtmTrunkEntry 2 } jnxAtmTrunkEncapsulation OBJECT-TYPE SYNTAX INTEGER { other(1), atmCccCellRelay(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The atm encapsulation type associated with the VC or Trunk. atmCccCellRelay : ATM Cell Relay for CCC" ::= { jnxAtmTrunkEntry 3 } jnxAtmTrunkFlags OBJECT-TYPE SYNTAX JnxAtmFlags MAX-ACCESS read-only STATUS current DESCRIPTION "Flags related to the Trunk." ::= { jnxAtmTrunkEntry 4 } jnxAtmTrunkTotalDownTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total Trunk down time in seconds ever since the system rebooted." ::= { jnxAtmTrunkEntry 5 } -- Traffic Stats jnxAtmTrunkInBytes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of bytes received on the Trunk." ::= { jnxAtmTrunkEntry 6 } jnxAtmTrunkOutBytes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of bytes sent out on the Trunk." ::= { jnxAtmTrunkEntry 7 } jnxAtmTrunkInPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets received on the Trunk." ::= { jnxAtmTrunkEntry 8 } jnxAtmTrunkOutPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets sent out on the Trunk." ::= { jnxAtmTrunkEntry 9 } jnxAtmTrunkTailQueuePktDrops OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets dropped due to bandwidth constraints. Indicates that packets were queued to send out at a rate faster than allowed." ::= { jnxAtmTrunkEntry 10 } -- OAM F4 Stats jnxAtmTrunkInOAMF4AISCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of OAM F4 cells received, with AIS(Alarm Indication Signal) bit set." ::= { jnxAtmTrunkEntry 15 } jnxAtmTrunkOutOAMF4AISCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of OAM F4 cells sent, with AIS(Alarm Indication Signal) bit set." ::= { jnxAtmTrunkEntry 16 } END