CTRON-SFPS-PORT-MIB DEFINITIONS ::= BEGIN -- sfps-port-mib.txt -- Revision: 0.0.11 -- -- Cabletron Systems, Inc. -- 35 Industrial Way, P.O. Box 5005 -- Rochester, NH 03867-0505 -- (603) 332-9400 -- support@ctron.com -- -- This module provides authoritative definitions for Cabletron's -- enterprise specific Fast Packet Switching Services API MIB. -- -- This module will be extended, as required. -- -- -- Cabletron Systems reserves the right to make changes in -- specification and other information contained in this document -- without prior notice. The reader should consult Cabletron Systems -- to determine whether any such changes have been made. -- -- In no event shall Cabletron Systems be liable for any incidental, -- indirect, special, or consequential damages whatsoever (including -- but not limited to lost profits) arising out of or related to this -- document or the information contained in it, even if Cabletron -- Systems has been advised of, known, or should have known, the -- possibility of such damages. -- -- Cabletron grants vendors, end-users, and other interested parties -- a non-exclusive license to use this Specification in connection -- with the management of Cabletron products. -- Copyright October 93 Cabletron Systems -- IMPORTS OBJECT-TYPE FROM RFC-1212 DisplayString FROM RFC1213-MIB -- tcl enterprises Counter, TimeTicks, Gauge FROM RFC1155-SMI -- These Objects are defined in the file sfps-inc.mib.txt.0.0.1 sfpsPortConfig, sfpsPortStats, sfpsPortAttributeTable, sfpsPortAttributeAPI FROM CTRON-SFPS-INCLUDE-MIB; -- Textual Conventions --SfpsSwitchInstance ::= OCTET STRING (SIZE(4)) -- this will map to chassis.module index value SfpsSwitchPort ::= INTEGER -- this will map to chassis.module.portgroup.portsubgroup.port index value --SfpsAddress ::= OCTET STRING (SIZE (6)) -- this will map to a MAC address HexInteger ::= INTEGER -- display this integer in hex format -- SFPS Switching Port Group -- This group contains the managed objects used to setup and -- configure the SFPS ports for packet switching and statisics -- monitoring. This group contains two sub-groups: configuration -- and statistics. -- SFPS Port Configuration Tables -- This table contains the managed objects used to set-up and configure -- each SFPS switching port. A seperate table exists for inbound ports -- and outbound ports. -- Inbound ports. sfpsInPortConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF SfpsInPortConfigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains the configuration information of each configured inbound SFPS switch port. If SFPS is not configured on a port, than an entry will not exist." ::= { sfpsPortConfig 1 } sfpsInPortConfigEntry OBJECT-TYPE SYNTAX SfpsInPortConfigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry specifies the SFPS configuration for the SFPS inbound switch port for which the entry exists." INDEX { sfpsInPortConfigPort } ::= { sfpsInPortConfigTable 1 } SfpsInPortConfigEntry ::= SEQUENCE { sfpsInPortConfigPort SfpsSwitchPort, sfpsInPortConfigAdminStatus INTEGER, sfpsInPortConfigOperStatus INTEGER, sfpsInPortConfigOperTime TimeTicks, sfpsInPortConfigType INTEGER, sfpsInPortConfigReservedBW INTEGER, sfpsInPortConfigAllocBW INTEGER, sfpsInPortConfigQoS INTEGER, sfpsInPortConfigQSize INTEGER, sfpsInPortConfigQLen Gauge, sfpsInPortConfigSwitchId OCTET STRING, sfpsInPortConfigMediaType INTEGER, sfpsInPortConfigFrontPanelPort SfpsSwitchPort, sfpsInPortConfigLinkStatus INTEGER, sfpsInPortConfigLinkStateAge TimeTicks, sfpsInPortConfigRouterPort INTEGER, sfpsInPortConfigSlotNumber INTEGER, sfpsInPortConfigMib2PortId INTEGER, sfpsInPortConfigTopoAgent DisplayString, sfpsInPortConfigLayer3Learning INTEGER } sfpsInPortConfigPort OBJECT-TYPE SYNTAX SfpsSwitchPort ACCESS read-only STATUS mandatory DESCRIPTION "The primary index to the SFPS in port table. This identifies the inbound SFPS switch port for which the entry exists." ::= { sfpsInPortConfigEntry 1 } sfpsInPortConfigAdminStatus OBJECT-TYPE SYNTAX INTEGER { other(1), disabled(2), enabled(3), loopback(4) } ACCESS read-write STATUS mandatory DESCRIPTION "Sets the administrative state of the SFPS inbound switch port for which the entry exists." ::= { sfpsInPortConfigEntry 2 } sfpsInPortConfigOperStatus OBJECT-TYPE SYNTAX INTEGER { other(1), -- none of the following disabled(2), -- not running enabled(3), -- running pending-disable(4), -- shut-down in progress pending-enable(5), -- start-up in progress invalid-config(6), -- not running,invalid config testing(7) -- in loopback mode } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the current operating condition of the SFPS on the inbound switch port for which this entry exists." ::= { sfpsInPortConfigEntry 3 } sfpsInPortConfigOperTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the elapsed time, in hundredths of a second, that sfpsInPortOperStatus has been in its current operational state on the SFPS inbound switch port for which this entry exists." ::= { sfpsInPortConfigEntry 4 } sfpsInPortConfigType OBJECT-TYPE SYNTAX INTEGER { other(1), access-port(2), network-port(3), host-mgmt-port(4), host-ctl-port(5), unknown(6), going-to-access(7), hybrid-port(8), stand-by(9), network-only(10), accessOnly(11), raPrimary(12), uplink(13), fclStandby(14), loopStandby(15), raStandby(16), flood(17), uplinkFlood(18), downlinkFlood(19), unknown-ra-standby(20) } ACCESS read-write STATUS mandatory DESCRIPTION "Sets the type of port access attribute for the inbound SFPS port for which the entry exists. Access ports allow single user or shared access and perform statisics and control; network ports are equivalent to trunk ports with no access control; host management port indicates the (virtual) port to which the (internal) management agent is attached; host control port indicates the port to redirect non-management packets." ::= { sfpsInPortConfigEntry 5 } sfpsInPortConfigReservedBW OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Sets the amount of Bandwidth that is reserved for the inbound SFPS port for which this entry exists. This bandwidth is set aside for this port and may be given to another port if unused." -- ? should this be in Mbits/sec or as a percentage of total b/w. -- Currently defined as percentage of total b/w in switch. ::= { sfpsInPortConfigEntry 6 } sfpsInPortConfigAllocBW OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Sets the amount of Bandwidth that is allocated for the inbound SFPS port for which this entry exists. This bandwidth may be less than the reserved bandwidth." -- ? should this be in Mbits/sec or as a percentage of total b/w. -- Currently defined as percentage of total b/w in switch. ::= { sfpsInPortConfigEntry 7 } sfpsInPortConfigQoS OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Sets the desired QoS service class for the inbound SFPS port for which this entry exists." -- ? should this map to the ATM service classes ::= { sfpsInPortConfigEntry 8 } sfpsInPortConfigQSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the maximum inbound queue size for this port. Size is indicated in packets (packet descriptors)." ::= { sfpsInPortConfigEntry 9 } sfpsInPortConfigQLen OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the actual inbound queue size for this port. Size is indicated in packets (packet descriptors). This is a transient value that reflects the current depth of queue." ::= { sfpsInPortConfigEntry 10 } sfpsInPortConfigSwitchId OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "This entry is the id of the port." ::= { sfpsInPortConfigEntry 11 } sfpsInPortConfigMediaType OBJECT-TYPE SYNTAX INTEGER { ethernet(1), fddi(2), atm-lec(3), token-ring(4), wan(5), inb(6), hcp(7), hdp(8), atm-svc(9), atm-pvc(10), unknown(11), atm-forum-lec(12), atm-forum-pvc(13), atm-forum-svc(14) } ACCESS read-only STATUS mandatory DESCRIPTION "" ::= { sfpsInPortConfigEntry 12 } sfpsInPortConfigFrontPanelPort OBJECT-TYPE SYNTAX SfpsSwitchPort ACCESS read-only STATUS mandatory DESCRIPTION "This represents the front panel physical port number" ::= { sfpsInPortConfigEntry 13 } sfpsInPortConfigLinkStatus OBJECT-TYPE SYNTAX INTEGER { other(1), linkUp(2), linkDown(3), link-N-A(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The link status of this port." ::= { sfpsInPortConfigEntry 14 } sfpsInPortConfigLinkStateAge OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "Number of time ticks that link has been in this state." ::= { sfpsInPortConfigEntry 15 } sfpsInPortConfigRouterPort OBJECT-TYPE SYNTAX INTEGER { other(1), router-port(2), no-router(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Specifies whether this port is a router port." ::= { sfpsInPortConfigEntry 16 } sfpsInPortConfigSlotNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Slot number in the chassis." ::= { sfpsInPortConfigEntry 17 } sfpsInPortConfigMib2PortId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Mib2 Port id" ::= { sfpsInPortConfigEntry 18 } sfpsInPortConfigTopoAgent OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Topology Agent" ::= { sfpsInPortConfigEntry 19 } sfpsInPortConfigLayer3Learning OBJECT-TYPE SYNTAX INTEGER { other(1), enabled(2), disabled(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Topology Agent" ::= { sfpsInPortConfigEntry 22 } -- Outbound Ports sfpsOutPortConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF SfpsOutPortConfigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains the configuration information of each configured outbound SFPS switch port. If SFPS is not configured on a port, than an entry will not exist." ::= { sfpsPortConfig 2 } sfpsOutPortConfigEntry OBJECT-TYPE SYNTAX SfpsOutPortConfigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry specifies the SFPS configuration for the SFPS outbound switch port for which the entry exists." INDEX { sfpsOutPortConfigPort } ::= { sfpsOutPortConfigTable 1 } SfpsOutPortConfigEntry ::= SEQUENCE { sfpsOutPortConfigPort SfpsSwitchPort, sfpsOutPortConfigAdminStatus INTEGER, sfpsOutPortConfigOperStatus INTEGER, sfpsOutPortConfigOperTime TimeTicks, sfpsOutPortConfigType INTEGER, sfpsOutPortConfigReservedBW INTEGER, sfpsOutPortConfigAllocBW INTEGER, sfpsOutPortConfigQoS INTEGER, sfpsOutPortConfigQSize INTEGER, sfpsOutPortConfigQLen Gauge, sfpsOutPortConfigSwitchId OCTET STRING, sfpsOutPortConfigMediaType INTEGER, sfpsOutPortConfigFrontPanelPort SfpsSwitchPort, sfpsOutPortConfigLinkStatus INTEGER, sfpsOutPortConfigLinkStateAge TimeTicks, sfpsOutPortConfigRouterPort INTEGER, sfpsOutPortConfigSlotNumber INTEGER, sfpsOutPortConfigMib2PortId INTEGER } sfpsOutPortConfigPort OBJECT-TYPE SYNTAX SfpsSwitchPort ACCESS read-only STATUS mandatory DESCRIPTION "The primary index to the SFPS in port table. This identifies the outbound SFPS switch port for which the entry exists." ::= { sfpsOutPortConfigEntry 1 } sfpsOutPortConfigAdminStatus OBJECT-TYPE SYNTAX INTEGER { other(1), disabled(2), enabled(3), loopback(4) } ACCESS read-write STATUS mandatory DESCRIPTION "Sets the administrative state of the SFPS outbound switch port for which the entry exists." ::= { sfpsOutPortConfigEntry 2 } sfpsOutPortConfigOperStatus OBJECT-TYPE SYNTAX INTEGER { other(1), -- none of the following disabled(2), -- not running enabled(3), -- running pending-disable(4), -- shut-down in progress pending-enable(5), -- start-up in progress invalid-config(6), -- not running,invalid config testing(7) -- in loopback mode } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the current operating condition of the SFPS on the outbound switch port for which this entry exists." ::= { sfpsOutPortConfigEntry 3 } sfpsOutPortConfigOperTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the elapsed time, in hundredths of a second, that sfpsOutPortOperStatus has been in its current operational state on the SFPS outbound switch port for which this entry exists." ::= { sfpsOutPortConfigEntry 4 } sfpsOutPortConfigType OBJECT-TYPE SYNTAX INTEGER { other(1), access-port(2), network-port(3), host-mgmt-port(4), host-ctl-port(5), unknown(6), going-to-access(7), hybrid-port(8), stand-by(9), network-only(10), accessOnly(11), raPrimary(12), standbyFCLConflict(13), standbyLoopedPort(14), standbyVersionConflict(15), standbyRANonPrimary(16), flood(17), uplinkFlood(18), downlinkFlood(19), unknown-ra-standby(20) } ACCESS read-write STATUS mandatory DESCRIPTION "Sets the type of port access attribute for the outbound SFPS port for which the entry exists. Access ports allow single user or shared access and perform statisics and control; network ports are equivalent to trunk ports with no access control; host management port indicates the (virtual) port to which the (internal) management agent is attached; host control port indicates the port to redirect non-management packets." ::= { sfpsOutPortConfigEntry 5 } sfpsOutPortConfigReservedBW OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Sets the amount of Bandwidth that is reserved for the outbound SFPS port for which this entry exists. This bandwidth is set aside for this port and may be given to another port if unused." -- ? should this be in Mbits/sec or as a percentage of total b/w. -- Currently defined as percentage of total b/w in switch. ::= { sfpsOutPortConfigEntry 6 } sfpsOutPortConfigAllocBW OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Sets the amount of Bandwidth that is allocated for the outbound SFPS port for which this entry exists. This bandwidth may be less than the reserved bandwidth." -- ? should this be in Mbits/sec or as a percentage of total b/w. -- Currently defined as percentage of total b/w in switch. ::= { sfpsOutPortConfigEntry 7 } sfpsOutPortConfigQoS OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Sets the desired QoS service class for the outbound SFPS port for which this entry exists." -- ? should this map to the ATM service classes ::= { sfpsOutPortConfigEntry 8 } sfpsOutPortConfigQSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the maximum outbound queue size for this port. Size is indicated in packets (packet descriptors)." ::= { sfpsOutPortConfigEntry 9 } sfpsOutPortConfigQLen OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the actual outbound queue size for this port. Size is indicated in packets (packet descriptors). This is a transient value that reflects the current depth of queue." ::= { sfpsOutPortConfigEntry 10 } sfpsOutPortConfigSwitchId OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "This entry is id of the port." ::= { sfpsOutPortConfigEntry 11 } sfpsOutPortConfigMediaType OBJECT-TYPE SYNTAX INTEGER { ethernet(1), fddi(2), atm-lec(3), token-ring(4), wan(5), inb(6), hcp(7), hdp(8), atm-encap(9), atm-pvc(10), unknown(11), atm-forum-lec(12), atm-forum-pvc(13), atm-forum-svc(14) } ACCESS read-only STATUS mandatory DESCRIPTION "" ::= { sfpsOutPortConfigEntry 12 } sfpsOutPortConfigFrontPanelPort OBJECT-TYPE SYNTAX SfpsSwitchPort ACCESS read-only STATUS mandatory DESCRIPTION "" ::= { sfpsOutPortConfigEntry 13 } sfpsOutPortConfigLinkStatus OBJECT-TYPE SYNTAX INTEGER { other(1), linkUp(2), linkDown(3), linkNA(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The link status of this port." ::= { sfpsOutPortConfigEntry 14 } sfpsOutPortConfigLinkStateAge OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "Number of time ticks that link has been in this state." ::= { sfpsOutPortConfigEntry 15 } sfpsOutPortConfigRouterPort OBJECT-TYPE SYNTAX INTEGER { other(1), router-port(2), no-router(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Specifies whether this port is a router port." ::= { sfpsOutPortConfigEntry 16 } sfpsOutPortConfigSlotNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Slot number in the chassis." ::= { sfpsOutPortConfigEntry 17 } sfpsOutPortConfigMib2PortId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Mib2 Port id" ::= { sfpsOutPortConfigEntry 18 } -- -- SFPS Switching Port Statistics Tables -- This table contains the objects that specify the packet and byte counters -- for each configured SFPS switching port. A separate table exists for -- inbound and outbound ports. -- Inbound ports. sfpsInPortStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF SfpsInPortStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains the packet and byte counters for each inbound SFPS switch port." ::= { sfpsPortStats 1 } sfpsInPortStatsEntry OBJECT-TYPE SYNTAX SfpsInPortStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Specifies the SFPS packet and byte counters for the inbound SFPS switch port for which this entry exists." INDEX { sfpsInPortStatsPort } ::= { sfpsInPortStatsTable 1 } SfpsInPortStatsEntry ::= SEQUENCE { sfpsInPortStatsPort SfpsSwitchPort, sfpsInPortStatsAdminStatus INTEGER, sfpsInPortStatsReset INTEGER, sfpsInPortStatsOperTime TimeTicks, sfpsInPortStatsPkts Counter, sfpsInPortStatsDiscardPkts Counter, sfpsInPortStatsBytes Counter, sfpsInPortStatsDiscardBytes Counter, sfpsInPortStatsQOverflows Counter, sfpsInPortStatsLinkUps Counter, sfpsInPortStatsLinkDowns Counter } sfpsInPortStatsPort OBJECT-TYPE SYNTAX SfpsSwitchPort ACCESS read-only STATUS mandatory DESCRIPTION "The primary index to the SFPS port table. This identifies the SFPS inbound switch port for which the entry exists." ::= { sfpsInPortStatsEntry 1 } sfpsInPortStatsAdminStatus OBJECT-TYPE SYNTAX INTEGER { other(1), disabled(2), enabled(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Sets the administrative state of the SFPS packet and byte counters on the inbound SFPS switch port for which this entry exists." ::= { sfpsInPortStatsEntry 2 } sfpsInPortStatsReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Resets the SFPS packet and byte counters on the inbound SFPS switch port for which this entry exists." ::= { sfpsInPortStatsEntry 3 } sfpsInPortStatsOperTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the amount of time (# of time ticks) that the port-specific SFPS packet and byte counters have been active on the inbound SFPS switch port for which this entry exists." ::= { sfpsInPortStatsEntry 4 } sfpsInPortStatsPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of SFPS packets that have been received, during sfpsInPortStatsOpertime, on the inbound SFPS switch port for which this entry exists." ::= { sfpsInPortStatsEntry 5 } sfpsInPortStatsDiscardPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of SFPS packets that have been discarded (dropped), during sfpsInPortStatsOpertime, on the inbound SFPS switch port for which this entry exists" ::= { sfpsInPortStatsEntry 6 } sfpsInPortStatsBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of SFPS bytes that have been received, during sfpsInPortStatsOperTime, on the inbound SFPS switch port for which the entry exists." ::= { sfpsInPortStatsEntry 7 } sfpsInPortStatsDiscardBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of bytes in the SFPS packets that have been discarded (dropped), during sfpsInPortStatsOperTime, on the inbound SFPS switch port for which the entry exists." ::= { sfpsInPortStatsEntry 8 } sfpsInPortStatsQOverflows OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of queue overflow conditions have been experienced for the inbound SFPS switch port for which the entry exists." ::= { sfpsInPortStatsEntry 9 } sfpsInPortStatsLinkUps OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of link ups that this port has seen." ::= { sfpsInPortStatsEntry 10 } sfpsInPortStatsLinkDowns OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of link downs that this port has seen." ::= { sfpsInPortStatsEntry 11 } -- -- Outbound ports. sfpsOutPortStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF SfpsOutPortStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains the packet and byte counters for each outbound SFPS switch port." ::= { sfpsPortStats 2 } sfpsOutPortStatsEntry OBJECT-TYPE SYNTAX SfpsOutPortStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Specifies the SFPS packet and byte counters for the outbound SFPS switch port for which this entry exists." INDEX { sfpsOutPortStatsPort } ::= { sfpsOutPortStatsTable 1 } SfpsOutPortStatsEntry ::= SEQUENCE { sfpsOutPortStatsPort SfpsSwitchPort, sfpsOutPortStatsAdminStatus INTEGER, sfpsOutPortStatsReset INTEGER, sfpsOutPortStatsOperTime TimeTicks, sfpsOutPortStatsPkts Counter, sfpsOutPortStatsDiscardPkts Counter, sfpsOutPortStatsBytes Counter, sfpsOutPortStatsDiscardBytes Counter, sfpsOutPortStatsQOverflows Counter, sfpsOutPortStatsLinkUps Counter, sfpsOutPortStatsLinkDowns Counter } sfpsOutPortStatsPort OBJECT-TYPE SYNTAX SfpsSwitchPort ACCESS read-only STATUS mandatory DESCRIPTION "The primary index to the SFPS port table. This identifies the SFPS outbound switch port for which the entry exists." ::= { sfpsOutPortStatsEntry 1 } sfpsOutPortStatsAdminStatus OBJECT-TYPE SYNTAX INTEGER { other(1), disabled(2), enabled(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Sets the administrative state of the SFPS packet and byte counters on the outbound SFPS switch port for which this entry exists." ::= { sfpsOutPortStatsEntry 2 } sfpsOutPortStatsReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Resets the SFPS packet and byte counters on the outbound SFPS switch port for which this entry exists." ::= { sfpsOutPortStatsEntry 3 } sfpsOutPortStatsOperTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the amount of time (# of time ticks) that the port-specific SFPS packet and byte counters have been active on the outbound SFPS switch port for which this entry exists." ::= { sfpsOutPortStatsEntry 4 } sfpsOutPortStatsPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of SFPS packets that have been received, during sfpsOutPortStatsOpertime, on the outbound SFPS switch port for which this entry exists." ::= { sfpsOutPortStatsEntry 5 } sfpsOutPortStatsDiscardPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of SFPS packets that have been discarded (dropped), during sfpsOutPortStatsOpertime, on the outbound SFPS switch port for which this entry exists" ::= { sfpsOutPortStatsEntry 6 } sfpsOutPortStatsBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of SFPS bytes that have been received, during sfpsOutPortStatsOperTime, on the outbound SFPS switch port for which the entry exists." ::= { sfpsOutPortStatsEntry 7 } sfpsOutPortStatsDiscardBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of bytes in the SFPS packets that have been discarded (dropped), during sfpsOutPortStatsOperTime, on the outbound SFPS switch port for which the entry exists." ::= { sfpsOutPortStatsEntry 8 } sfpsOutPortStatsQOverflows OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of queue overflow conditions have been experienced for the outbound SFPS switch port for which the entry exists." ::= { sfpsOutPortStatsEntry 9 } sfpsOutPortStatsLinkUps OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of link ups that this port has seen." ::= { sfpsOutPortStatsEntry 10 } sfpsOutPortStatsLinkDowns OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of link downs that this port has seen." ::= { sfpsOutPortStatsEntry 11 } -- Port Attributes sfpsPortAttributePort OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "" ::= { sfpsPortAttributeTable 1 } sfpsPortAttributeAttributes OBJECT-TYPE SYNTAX HexInteger ACCESS read-only STATUS mandatory DESCRIPTION "" ::= { sfpsPortAttributeTable 2 } sfpsPortAttributeLearnSelfArp OBJECT-TYPE SYNTAX INTEGER { off(2), on(1) } ACCESS read-only STATUS mandatory DESCRIPTION "" ::= { sfpsPortAttributeTable 3 } -- Port Attributes API sfpsPortAttributeAPIVerb OBJECT-TYPE SYNTAX INTEGER { other(1), resetAll(2), resetPort(3), enablePortAttr(4), disablePortAttr(5) } ACCESS read-write STATUS mandatory DESCRIPTION "" ::= { sfpsPortAttributeAPI 1 } sfpsPortAttributeAPIPort OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "" ::= { sfpsPortAttributeAPI 2 } sfpsPortAttributeAPIAttribute OBJECT-TYPE SYNTAX INTEGER { none(2), learnSelfArp(1) } ACCESS read-write STATUS mandatory DESCRIPTION "" ::= { sfpsPortAttributeAPI 3 } END