CTRON-REMOTE-ACCESS-MIB DEFINITIONS ::= BEGIN -- ctron-remote-access-mib.txt The Cabletron Remote Access MIB. -- Revision: 1.00.04 -- Part Number: -- Date: November 24, 1998 -- Cabletron Systems, Inc. -- 35 Industrial Way, P.O. Box 5005 -- Rochester, NH 03867-0505 -- (603) 332-9400 -- support@ctron.com -- This module provides authoritative definitions for part -- of the naming tree below: -- -- cabletron { enterprises 52 } -- -- This module will be extended, as additional sub-sections -- of this naming tree are defined. -- -- Cabletron Systems reserves the right to make changes in -- specification and other information contained in this document -- without prior notice. The reader should consult Cabletron Systems -- to determine whether any such changes have been made. -- -- In no event shall Cabletron Systems be liable for any incidental, -- indirect, special, or consequential damages whatsoever (including -- but not limited to lost profits) arising out of or related to this -- document or the information contained in it, even if Cabletron -- Systems has been advised of, known, or should have known, the -- possibility of such damages. -- -- Cabletron grants vendors, end-users, and other interested parties -- a non-exclusive license to use this Specification in connection -- with the management of Cabletron products. -- Copyright August 1997 Cabletron Systems IMPORTS IpAddress, Counter,enterprises FROM RFC1155-SMI DisplayString FROM RFC1213-MIB OBJECT-TYPE FROM RFC-1212; Index ::= INTEGER DLCI ::= INTEGER -- DisplayString ::= OCTET STRING cabletron OBJECT IDENTIFIER ::= { enterprises 52 } -- 1.3.6.1.4.1.52 mibs OBJECT IDENTIFIER ::= { cabletron 4 } -- 1.3.6.1.4.1.52.4 ctron OBJECT IDENTIFIER ::= { mibs 1 } -- 1.3.6.1.4.1.52.4.1 ctDataLink OBJECT IDENTIFIER ::= { ctron 2 } -- 1.3.6.1.4.1.52.4.1.2 ctronWan OBJECT IDENTIFIER ::= { ctDataLink 7 } -- 1.3.6.1.4.1.52.4.1.2.7 ctRemoteAccess OBJECT IDENTIFIER ::= { ctronWan 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2 ---------------------------------------------------------- -- Groups ctRemoteConnection OBJECT IDENTIFIER ::= { ctRemoteAccess 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1 ctDs1Ext OBJECT IDENTIFIER ::= { ctRemoteAccess 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.2 ctRs232Ext OBJECT IDENTIFIER ::= { ctRemoteAccess 3 } -- 1.3.6.1.4.1.52.4.1.2.7.2.3 ctFrDcp OBJECT IDENTIFIER ::= { ctRemoteAccess 4 } -- 1.3.6.1.4.1.52.4.1.2.7.2.4 ctDDSExt OBJECT IDENTIFIER ::= { ctRemoteAccess 5 } -- 1.3.6.1.4.1.52.4.1.2.7.2.5 ctPPPExt OBJECT IDENTIFIER ::= { ctRemoteAccess 6 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6 ctWanalyzer OBJECT IDENTIFIER ::= { ctRemoteAccess 7 } -- 1.3.6.1.4.1.52.4.1.2.7.2.7 ctDs1Alarms OBJECT IDENTIFIER ::= { ctRemoteAccess 8 } -- 1.3.6.1.4.1.52.4.1.2.7.2.8 ctIPPQFilters OBJECT IDENTIFIER ::= { ctRemoteAccess 9 } -- 1.3.6.1.4.1.52.4.1.2.7.2.9 ctDs3Ext OBJECT IDENTIFIER ::= { ctRemoteAccess 10 } -- 1.3.6.1.4.1.52.4.1.2.7.2.10 -- Cabletron Remote Access Connection Group -- This group is mandatory for all platforms that have one or more -- physical remote access connections ctRemNumConnections OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object describes the number of physical remote access connections on the platform." ::= { ctRemoteConnection 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.1 ctRemPhysPortTable OBJECT-TYPE SYNTAX SEQUENCE OF CtRemPhysPortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of the descriptions of the physical remote access ports of this platform." ::= { ctRemoteConnection 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.2 ctRemPhysPortEntry OBJECT-TYPE SYNTAX CtRemPhysPortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A physical port entry. It contains objects relating to a given physical remote access port" INDEX { ctRemConnectionIndex } ::= { ctRemPhysPortTable 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1 CtRemPhysPortEntry ::= SEQUENCE { ctRemConnectionIndex INTEGER, ctRemPhysPortType INTEGER, ctRemPhysPortSpecificMib OBJECT IDENTIFIER, ctRemPhysPortProtMgrType INTEGER, ctRemPhysPortProtMgrIfaceNum INTEGER, ctRemPhysPortWanIfaceNum INTEGER, ctRemPhysPortProtMgrMaxIfos INTEGER, ctRemPhysPortProtMgrIfaceList DisplayString, ctRemPhysAlarmTimeOut INTEGER, ctRemPhysWpimType INTEGER } ctRemConnectionIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A value indicating the remote connection this entry is located on." ::= { ctRemPhysPortEntry 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.1 ctRemPhysPortType OBJECT-TYPE SYNTAX INTEGER { none(1), t1(2), e1(3), synchronous(4), dds(5), di(6), -- Drop and Insert hdsl(7), isdnBRI(8), ds30(9), t1dds(10) } ACCESS read-only STATUS mandatory DESCRIPTION "The type of physical port that this entry describes. None indicates that the physical port has no connector." DEFVAL { none } ::= { ctRemPhysPortEntry 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.2 ctRemPhysPortSpecificMib OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS mandatory DESCRIPTION "This object identifies an instance of the index object in the first group of objects in the MIB specific to the physical port." ::= { ctRemPhysPortEntry 3 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.3 ctRemPhysPortProtMgrType OBJECT-TYPE SYNTAX INTEGER { none(1), pppNailedUp(2), isdnPriPpp(3), isdnBriPpp(4), frameRelayPvcRtr(5), frameRelayPvcSw(6), hdlc(7) } ACCESS read-write STATUS mandatory DESCRIPTION "This object identifies an instance of the type of Protocol Manager residing on this physical port. Before a physical port may be used, the type of manager must be designated. For example, if the physical port was going to be used as an ISDN PRI interface, with dial up PPP links, then the manager type would be set to (4), ISDN-PRI-PPP." DEFVAL { none } ::= { ctRemPhysPortEntry 4 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.4 ctRemPhysPortProtMgrIfaceNum OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object identifies the interface number that will be assigned to the Protocol Managers IFO" ::= { ctRemPhysPortEntry 5 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.5 ctRemPhysPortWanIfaceNum OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object identifies the interface number that will be assigned to the Wanio's IFO" ::= { ctRemPhysPortEntry 6 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.6 ctRemPhysPortProtMgrMaxIfos OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object identifies the maximum number of IFO's that can be created on this physical interface." ::= { ctRemPhysPortEntry 7 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.7 ctRemPhysPortProtMgrIfaceList OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This object identifies a list of interfaces that will be assigned to this Protocol Managers data IFO's" ::= { ctRemPhysPortEntry 8 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.8 ctRemPhysAlarmTimeOut OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Whenever the physical port is configured for nailed-up PPP this object specifies the time the physical port must remain in a failed state as a condition to begin the backup procedure. The backup procedure is begun for any active interface(s) that were connected over the failed physical port and which have been configured for backup." ::= { ctRemPhysPortEntry 9 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.9 ctRemPhysWpimType OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This Mib object determines the Mode of operation that the T1/DDS Wpim module will function as. Setting a value of 1 will set the mode to DDS, setting a value of 2 will set the mode to T1." DEFVAL { 2 } ::= { ctRemPhysPortEntry 10 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.10 ctRemInterfaceTable OBJECT-TYPE SYNTAX SEQUENCE OF CtRemInterfaceEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The interface table for Cabletron remote interfaces. It is a list of items that are pertinant to the interfaces that are part of remote physical ports. The number of entries is dependent upon the total number of remote interfaces configured." ::= { ctRemoteConnection 3 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.3 ctRemInterfaceEntry OBJECT-TYPE SYNTAX CtRemInterfaceEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A remote interface entry. It contains objects relating to an interface that is defined for remote Cabletron products." INDEX { ctRemIntEntIfIndex } ::= { ctRemInterfaceTable 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1 CtRemInterfaceEntry ::= SEQUENCE { ctRemIntEntIfIndex INTEGER, ctRemIntEntCompression INTEGER, ctRemIntEntCompRatio DisplayString, ctRemIntEntCompStatus INTEGER, ctRemIntEntMTU INTEGER, ctRemIntEntCongestion INTEGER, ctRemIntEntMaxProfiles INTEGER, ctRemIntEntTxIdleTimeout INTEGER, ctRemIntEntRxIdleTimeout INTEGER, ctRemIntEntCircuitName DisplayString, ctRemIntEntEncryption INTEGER, ctRemIntEntEncryptStatus INTEGER } ctRemIntEntIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The ifIndex of the interface. This is the index of this entry in the ifTable." REFERENCE "rfc-1213" ::= { ctRemInterfaceEntry 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.1 ctRemIntEntCompression OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This flag will indicate whether compression should take place on this interface." DEFVAL { off } ::= { ctRemInterfaceEntry 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.2 ctRemIntEntCompRatio OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This string indicates the current compression ratio on this interface." ::= { ctRemInterfaceEntry 3 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.3 ctRemIntEntCompStatus OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "This flag will indicate whether compression has been nogotiated on this interface." ::= { ctRemInterfaceEntry 4 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.4 ctRemIntEntMTU OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The MTU to be negotiated for this interface. This will not be updated with the actual MTU, which can be found in the ifTable." ::= { ctRemInterfaceEntry 5 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.5 ctRemIntEntCongestion OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This object identifies the Leaky Bucket algorithm flag for a Frame Relay circuit on this intertface. The option is supported when this flag is enabled, and not supported when this flag is disabled." DEFVAL { disabled } ::= { ctRemInterfaceEntry 6 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.6 ctRemIntEntMaxProfiles OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object specifies the maximum number of neighbor profiles. A neighbor profile describes a possible connection. The maximum should be set to account for support of PPP multilink. That is to say, if PPP multilink is being used then the number of profiles must at least accomodate the maximum possible number of additional more BW connections. As such, each neighbor profile would then describe a possible connection to the same remote end point." ::= { ctRemInterfaceEntry 7 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.7 ctRemIntEntTxIdleTimeout OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object identifies the idle timeout value in which a packet needs to be transmitted before the interface is automatically disconnected. Allowed values are in increments of five seconds including zero." ::= { ctRemInterfaceEntry 8 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.8 ctRemIntEntRxIdleTimeout OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object identifies the idle timeout in which a packet needs to be received before the interface is automatically disconnected. Allowed values are in increments of five seconds including zero." ::= { ctRemInterfaceEntry 9 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.9 ctRemIntEntCircuitName OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS mandatory DESCRIPTION "This object associates a circuit name with a specific interface." ::= { ctRemInterfaceEntry 10 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.10 ctRemIntEntEncryption OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This flag will indicate whether encryption should take place on this interface." DEFVAL { off } ::= { ctRemInterfaceEntry 11 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.11 ctRemIntEntEncryptStatus OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "This flag will indicate whether Encryption has been nogotiated on this interface." ::= { ctRemInterfaceEntry 12 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.12 ctRemPrimaryInterfaceTable OBJECT-TYPE SYNTAX SEQUENCE OF CtRemPrimaryInterfaceEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The interface table for Cabletron remote interfaces. It is a list of items that are pertinant to the interfaces that are part of remote physical ports. The number of entries is dependent upon the total number of remote interfaces configured." ::= { ctRemoteConnection 4 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.4 ctRemPrimaryInterfaceEntry OBJECT-TYPE SYNTAX CtRemPrimaryInterfaceEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A remote interface entry. It contains objects relating to an interface that is defined for remote Cabletron products." INDEX { ctRemPriIntEntIfIndex } ::= { ctRemPrimaryInterfaceTable 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.4.1 CtRemPrimaryInterfaceEntry ::= SEQUENCE { ctRemPriIntEntIfIndex INTEGER, ctRemPriIntEntConnectRetryInterval INTEGER } ctRemPriIntEntIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The ifIndex of the interface. This is the index of this entry in the ifTable." REFERENCE "rfc-1213" ::= { ctRemPrimaryInterfaceEntry 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.4.1.1 ctRemPriIntEntConnectRetryInterval OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object specifies the interval in seconds between retries for restoring the primary interface." DEFVAL { 30 } ::= { ctRemPrimaryInterfaceEntry 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.4.1.2 ctRemBackupInterfaceTable OBJECT-TYPE SYNTAX SEQUENCE OF CtRemBackupInterfaceEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The interface table for Cabletron remote interfaces. It is a list of items that are pertinant to the interfaces that are part of remote physical ports. The number of entries is dependent upon the total number of remote interfaces configured." ::= { ctRemoteConnection 5 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.5 ctRemBackupInterfaceEntry OBJECT-TYPE SYNTAX CtRemBackupInterfaceEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A remote interface entry. It contains objects relating to an interface that is defined for remote Cabletron products." INDEX { ctRemIntEntBackupIfIndex } ::= { ctRemBackupInterfaceTable 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.5.1 CtRemBackupInterfaceEntry ::= SEQUENCE { ctRemIntEntBackupIfIndex INTEGER, ctRemIntEntBackupIfNum INTEGER, ctRemIntEntBackupIfInUseCnt INTEGER, ctRemIntEntBackupIfTimeToConnect INTEGER, ctRemIntEntBackupIfTimeToDisconnect INTEGER, ctRemIntEntBackupIfOverride INTEGER, ctRemIntEntBackupConnectRetries INTEGER, ctRemIntEntBackupConnectRetryInterval INTEGER } ctRemIntEntBackupIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The ifIndex of the interface. This is the index of this entry in the ifTable." REFERENCE "rfc-1213" ::= { ctRemBackupInterfaceEntry 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.5.1.1 ctRemIntEntBackupIfNum OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object identifies which ifIndex will backup this interface in the event of a communications failure." ::= { ctRemBackupInterfaceEntry 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.5.1.2 ctRemIntEntBackupIfInUseCnt OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object identifies how many other interfaces this interface will backup." ::= { ctRemBackupInterfaceEntry 3 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.5.1.3 ctRemIntEntBackupIfTimeToConnect OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object identifies how long to wait in seconds before attempting to switchover to the backup interface. Allowed values are in increments of five seconds including zero." ::= { ctRemBackupInterfaceEntry 4 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.5.1.4 ctRemIntEntBackupIfTimeToDisconnect OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object identifies how long to wait in seconds before attempting to switchover to the primary interface. Allowed values are in increments of five seconds including zero." ::= { ctRemBackupInterfaceEntry 5 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.5.1.5 ctRemIntEntBackupIfOverride OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This object identifies if the interface will switch back to the primary link after it has become active again. A force condition will not allow the interface to switch back." DEFVAL { disabled } ::= { ctRemBackupInterfaceEntry 6 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.5.1.6 ctRemIntEntBackupConnectRetries OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object specifies the number of tries to bring-up the backup interface before giving up." ::= { ctRemBackupInterfaceEntry 7 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.5.1.7 ctRemIntEntBackupConnectRetryInterval OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object specifies the interval in seconds between retries for bringing up backup interface before giving up." ::= { ctRemBackupInterfaceEntry 8 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.5.1.8 ctRemExtPhysPortTable OBJECT-TYPE SYNTAX SEQUENCE OF CtRemExtPhysPortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of the descriptions of the physical remote access ports of this platform." ::= { ctRemoteConnection 6 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.6 ctRemExtPhysPortEntry OBJECT-TYPE SYNTAX CtRemExtPhysPortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A physical port entry. It contains objects relating to a given physical remote access port" INDEX { ctRemExtConnectionIndex } ::= { ctRemExtPhysPortTable 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.6.1 CtRemExtPhysPortEntry ::= SEQUENCE { ctRemExtConnectionIndex INTEGER, ctRemExtProtMgrIndex INTEGER, ctRemExtPhysPortProtMgrType INTEGER, ctRemExtPhysPortProtMgrEnable INTEGER, ctRemExtPhysPortProtMgrIfaceNum INTEGER, ctRemExtPhysPortProtMgrMaxIfos INTEGER, ctRemExtPhysPortProtMgrIfaceList DisplayString, ctRemExtPhysPortProtMgrChannelList DisplayString } ctRemExtConnectionIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A value indicating the remote connection this entry is located on." ::= { ctRemExtPhysPortEntry 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.6.1.1 ctRemExtProtMgrIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A value indicating the protMgr number for this entry." ::= { ctRemExtPhysPortEntry 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.6.1.2 ctRemExtPhysPortProtMgrType OBJECT-TYPE SYNTAX INTEGER { none(1), pppNailedUp(2), isdnPriPpp(3), isdnBriPpp(4), frameRelayPvcRtr(5), frameRelayPvcSw(6), hdlc(7) } ACCESS read-write STATUS mandatory DESCRIPTION "This object identifies an instance of the type of Protocol Manager residing on this physical port. Before a physical port may be used, the type of manager must be designated. For example, if the physical port was going to be used as an ISDN PRI interface, with dial up PPP links, then the manager type would be set to (4), ISDN-PRI-PPP." DEFVAL { none } ::= { ctRemExtPhysPortEntry 3 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.6.1.3 ctRemExtPhysPortProtMgrEnable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This object identifies an instance of the the enable flag of Protocol Manager residing on this physical port." DEFVAL { disabled } ::= { ctRemExtPhysPortEntry 4 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.6.1.4 ctRemExtPhysPortProtMgrIfaceNum OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object identifies the interface number that will be assigned to the Protocol Managers IFO" ::= { ctRemExtPhysPortEntry 5 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.6.1.5 ctRemExtPhysPortProtMgrMaxIfos OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object identifies the maximum number of IFO's that can be created on this physical interface." ::= { ctRemExtPhysPortEntry 6 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.6.1.6 ctRemExtPhysPortProtMgrIfaceList OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This object identifies a list of interfaces that will be assigned to this Protocol Managers data IFO's" ::= { ctRemExtPhysPortEntry 7 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.6.1.7 ctRemExtPhysPortProtMgrChannelList OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This object identifies a list of channles/timeslots that will be assigned to this Protocol Managers data IFO's" ::= { ctRemExtPhysPortEntry 8 } -- 1.3.6.1.4.1.52.4.1.2.7.2.1.6.1.8 -- Cabletron Ds1 Extensions Group -- This group is required for any platforms that have a t1 or e1 physical -- port. ctDs1ExtensionsTable OBJECT-TYPE SYNTAX SEQUENCE OF CtDs1ExtensionsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table is an extension to the standard ds1 configuration table. It is a list of items that are pertinant to ds1 ports on a platform. There is one entry per ds1 physical port on the platform." ::= { ctDs1Ext 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.2.1 ctDs1ExtensionsEntry OBJECT-TYPE SYNTAX CtDs1ExtensionsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A ds1 extensions entry containing objects relating to the particular ds1 physical port." INDEX { ctDs1ExtensionsEntryIndex } ::= { ctDs1ExtensionsTable 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1 CtDs1ExtensionsEntry ::= SEQUENCE { ctDs1ExtensionsEntryIndex INTEGER, ctDs1ExtensionsNumInterfaces INTEGER, ctDs1ExtensionsToggleFracTable INTEGER, ctDs1ExtensionsLineBuildOut INTEGER, ctDs1ExtensionsCFADuration INTEGER, ctDs1ExtensionsDIEnable INTEGER, ctDs1ExtensionsTotalValidIntervals Counter, wanDs1ExtensionsBertTestMode INTEGER, wanDs1ExtensionsBertRun INTEGER, wanDs1ExtensionsBertCurrentResults INTEGER, wanDs1ExtensionsBertCumulativeResults INTEGER, wanDs1ExtensionsBertPeakResults INTEGER, wanDs1ExtensionsBertAverageResult INTEGER, wanDs1ExtensionsBertTestPattern INTEGER, wanDs1ExtensionsBertSamplePeriod INTEGER, wanDs1ExtensionsBertNumPeriods Counter, wanDs1ExtensionsBertTestTraps INTEGER, wanDs1ExtensionsBertDataStatus INTEGER } ctDs1ExtensionsEntryIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A unique value for each ds1 physical port on the platform." ::= { ctDs1ExtensionsEntry 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.1 ctDs1ExtensionsNumInterfaces OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of interfaces on this physical port. This number inidicates the number of entries this physical port uses in the ifTable." REFERENCE "rfc-1213" ::= { ctDs1ExtensionsEntry 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.2 ctDs1ExtensionsToggleFracTable OBJECT-TYPE SYNTAX INTEGER { update-table(1), display-new(2), display-old(3), restore-old(4) } ACCESS read-write STATUS mandatory DESCRIPTION "Setting this object to 1 will cause the Ds1 Fractional Table to be updated with the new values, as entered. Setting this object to 2, will cause the Ds1 Fractional Table to view as the table being entered. Setting this object to 3, will cause the Ds1 Fractional Table to be the table that is currently in use, regardless of any changes being entered. Setting this object to 4, will cause any changes that have been made to the Ds1 Fractional Table since the last update-table to be deleted. For physical ports that are of type synch, or for Ds1 ports that do not support the Ds1 Fractional Table, this object will have no affect, and will always return a 1." REFERENCE "rfc-1406" ::= { ctDs1ExtensionsEntry 3 } -- 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.3 ctDs1ExtensionsLineBuildOut OBJECT-TYPE SYNTAX INTEGER { unknown(1), zero(2), minus-7point5(3), minus-15(4), a133to266feet(5), a266to399feet(6), a399to533feet(7), a533to655feet(8) } ACCESS read-write STATUS mandatory DESCRIPTION "The line build out setting for this ds1 physical port. Unknown indicates that the setting is neither readable or writable." DEFVAL { zero } ::= { ctDs1ExtensionsEntry 4 } -- 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.4 ctDs1ExtensionsCFADuration OBJECT-TYPE SYNTAX INTEGER (1..15) ACCESS read-write STATUS mandatory DESCRIPTION "The length of time (in seconds), that the ds1 port will remain in the Carrier Failure Alarm state after the alarm condition has cleared. For those Ds1 ports not supporting Carrier Failure Alarm duration, this object always returns 1, and setting the object has no effect." ::= { ctDs1ExtensionsEntry 5 } -- 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.5 ctDs1ExtensionsDIEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enables or disables Drop and Insert functionality on a D/I WPIM. If enabled, all zero assigned timeslots will designate D/I interface channels, if disabled all zero channels will designate dummy channels as on a T1 or E1." DEFVAL { enable } ::= { ctDs1ExtensionsEntry 6 } -- 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.6 ctDs1ExtensionsTotalValidIntervals OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of previous intervals for which valid data was collected for the DS1 mib, which is currently RFC1406. This counter is similar to RFC1406 dsx1ValidIntervals except that the count represents the total number of complete 15 minute intervals since the ds1 interface has been online, and does not stop at the 24 hour period." ::= { ctDs1ExtensionsEntry 7 } -- 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.7 wanDs1ExtensionsBertTestMode OBJECT-TYPE SYNTAX INTEGER{ none(1), internal(2), manual(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This object is used to request that a type of process be in control of the testing function. This is used to differentiate between automated test procedures and those manually controlled by a user. When read, this object reflects which type of process is actually in control of the testing function. The implementation is free to prioritize or deny requests in a proprietary manner." ::= { ctDs1ExtensionsEntry 8 } -- 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.8 wanDs1ExtensionsBertRun OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Controls the sending of test data over this physical port. The data is a pattern described by wanDs1ExtensionsBertTestPattern." ::= { ctDs1ExtensionsEntry 9 } -- 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.9 wanDs1ExtensionsBertCurrentResults OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the results of the testing for the last completed sampling period. A non-negative number is the error rate in bits per million bits." ::= { ctDs1ExtensionsEntry 10 } -- 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.10 wanDs1ExtensionsBertCumulativeResults OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of errors since the testing was enabled. It is not a rate." ::= { ctDs1ExtensionsEntry 11 } -- 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.11 wanDs1ExtensionsBertPeakResults OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the highest value of wanDs1ExtensionsBertCurrentResults since the testing was enabled. A non-negative number is the error rate in bits per million bits." ::= { ctDs1ExtensionsEntry 12 } -- 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.12 wanDs1ExtensionsBertAverageResult OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the average value of wanDs1ExtensionsBertCurrentResults since the testing was enabled. A non-negative number is the error rate in bits per million bits." ::= { ctDs1ExtensionsEntry 13 } -- 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.13 wanDs1ExtensionsBertTestPattern OBJECT-TYPE SYNTAX INTEGER { patternOther(1), pattern1s(2), pattern63(3), pattern511(4), pattern2047(5), pattern3in24(6), patternQRSS(7) } ACCESS read-write STATUS mandatory DESCRIPTION "This object is used to specify the pattern of the test data." ::= { ctDs1ExtensionsEntry 14 } -- 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.14 wanDs1ExtensionsBertSamplePeriod OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object is the duration of time in seconds at which the current test results will be periodically written to wanDs1ExtensionsBertCurrentResults. The range is 1 to 3600, with a default value of 10." ::= { ctDs1ExtensionsEntry 15 } -- 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.15 wanDs1ExtensionsBertNumPeriods OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION " The number of sampling periods that have elapsed during the current test run." ::= { ctDs1ExtensionsEntry 16 } -- 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.16 wanDs1ExtensionsBertTestTraps OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This object is used to enable or disable the sending of a trap at the conclusion of the measurement period. The trap will contain the information described by ctDs1BertCurrentResults. The default value is disabled." ::= { ctDs1ExtensionsEntry 17 } -- 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.17 wanDs1ExtensionsBertDataStatus OBJECT-TYPE SYNTAX INTEGER { idle(1), waitingForLink(2), waitingForLoopback(3), running(4) } ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the operating status of the transmission of test data packets." ::= { ctDs1ExtensionsEntry 18 } -- 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.18 ctDs1WanDriverTable OBJECT-TYPE SYNTAX SEQUENCE OF CtDs1WanDriverEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table is an extension to the standard ds1 configuration table. It is a list of items that are pertinant to the hdlc driver on a platform. There is one entry per ds1 physical port on the platform." ::= { ctDs1Ext 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.2.2 ctDs1WanDriverEntry OBJECT-TYPE SYNTAX CtDs1WanDriverEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A ds1 wan driver entry containing objects relating to the particular ds1 physical port pertaining to a specific channel on the wan driver chip." INDEX { ctDs1WanDriverEntryIndex, ctDs1WanDriverChannelIndex } ::= { ctDs1WanDriverTable 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.2.2.1 CtDs1WanDriverEntry ::= SEQUENCE { ctDs1WanDriverEntryIndex INTEGER, ctDs1WanDriverChannelIndex INTEGER, ctDs1WanDriverLineCode INTEGER, ctDs1WanDriverCRCBits INTEGER } ctDs1WanDriverEntryIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A unique value for each ds1 physical port on the platform." ::= { ctDs1WanDriverEntry 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.2.2.1.1 ctDs1WanDriverChannelIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A unique value for each channel on a wan driver on the platform." ::= { ctDs1WanDriverEntry 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.2.2.1.2 ctDs1WanDriverLineCode OBJECT-TYPE SYNTAX INTEGER { none (1), jBZS (2), invHDLC (3) } ACCESS read-write STATUS mandatory DESCRIPTION "This object controls the individual channels line coding on a wan driver device on the platform." DEFVAL { none } ::= { ctDs1WanDriverEntry 3 } -- 1.3.6.1.4.1.52.4.1.2.7.2.2.2.1.3 ctDs1WanDriverCRCBits OBJECT-TYPE SYNTAX INTEGER { crc16 (1), crc32 (2) } ACCESS read-write STATUS mandatory DESCRIPTION "This object controls the individual channels CRC bits generation on a wan driver device on the platform." DEFVAL { crc16 } ::= { ctDs1WanDriverEntry 4 } -- 1.3.6.1.4.1.52.4.1.2.7.2.2.2.1.4 -- Cabletron Rs232 Extensions Group -- This group is only required if any physical port on the system can be -- classified as rs232-like ctRs232ExtensionsTable OBJECT-TYPE SYNTAX SEQUENCE OF CtRs232ExtensionsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table is an extension to the standard rs232-like mib. It is a list of items that are pertinant to rs232-like ports on a platform. There is one entry per synchronous physical port on the platform." REFERENCE "rfc-1317" ::= { ctRs232Ext 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.3.1 ctRs232ExtensionsEntry OBJECT-TYPE SYNTAX CtRs232ExtensionsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A rs232-like extensions entry containing objects relating to the particular rs232-like physical port." INDEX { ctRs232ExtensionsEntryIndex } ::= { ctRs232ExtensionsTable 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.3.1.1 CtRs232ExtensionsEntry ::= SEQUENCE { ctRs232ExtensionsEntryIndex INTEGER, ctRs232ExtensionsCTSEnable INTEGER, ctRs232ExtensionsDSREnable INTEGER, ctRs232ExtensionsRTSEnable INTEGER, ctRs232ExtensionsDTREnable INTEGER } ctRs232ExtensionsEntryIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A unique value for each rs232-like physical port on the platform." ::= { ctRs232ExtensionsEntry 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.3.1.1.1 ctRs232ExtensionsCTSEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This object indicates whether the platform should generate CTS. When disabled the platform will not generate CTS, when enabled, the platform will generate CTS. The actual state of the CTS line is available in the rs-232 like mib." REFERENCE "rfc-1317" DEFVAL { disable } ::= { ctRs232ExtensionsEntry 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.3.1.1.2 ctRs232ExtensionsDSREnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This object indicates whether the platform should generate DSR. When disabled the platform will not generate DSR, when enabled, the platform will generate DSR. The actual state of the DSR line is available in the rs-232 like mib." REFERENCE "rfc-1317 " DEFVAL { disable } ::= { ctRs232ExtensionsEntry 3 } -- 1.3.6.1.4.1.52.4.1.2.7.2.3.1.1.3 ctRs232ExtensionsRTSEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This object indicates whether the platform should generate RTS. When disabled the platform will not generate RTS, when enabled, the platform will generate RTS. The actual state of the RTS line is available in the rs-232 like mib." REFERENCE "rfc-1317" DEFVAL { disable } ::= { ctRs232ExtensionsEntry 4 } -- 1.3.6.1.4.1.52.4.1.2.7.2.3.1.1.4 ctRs232ExtensionsDTREnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This object indicates whether the platform should generate DTR. When disabled the platform will not generate DSR, when enabled, the platform will generate DTR. The actual state of the DTR line is available in the rs-232 like mib." REFERENCE "rfc-1317 " DEFVAL { disable } ::= { ctRs232ExtensionsEntry 5 } -- 1.3.6.1.4.1.52.4.1.2.7.2.3.1.1.5 -- ctFrDcp Group -- This group is mandatory to support Data Compression Protocol -- (DCP following FRF.9) for per virtual circuit basis frDcpCircuitTable OBJECT-TYPE SYNTAX SEQUENCE OF FrDcpCircuitEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing data compression information about specific Data Link Connection Identifiers and corresponding virtual circuit. This information is used to support the frCircuitTable following RFC-1315." ::= { ctFrDcp 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.4.1 frDcpCircuitEntry OBJECT-TYPE SYNTAX FrDcpCircuitEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The data compression information regarding a single Data Link Connection Identifier." INDEX { frDcpCircuitIfIndex, frDcpCircuitDlci } ::= { frDcpCircuitTable 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.4.1.1 FrDcpCircuitEntry ::= SEQUENCE { frDcpCircuitIfIndex Index, frDcpCircuitDlci DLCI, frDcpCircuitEnable INTEGER, frDcpCircuitStatus INTEGER, frDcpCircuitRatio OCTET STRING } frDcpCircuitIfIndex OBJECT-TYPE SYNTAX Index ACCESS read-only STATUS mandatory DESCRIPTION "The ifIndex value of ifEntry that this DCP virtual circuit object is layered onto." ::= { frDcpCircuitEntry 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.4.1.1.1 frDcpCircuitDlci OBJECT-TYPE SYNTAX DLCI ACCESS read-only STATUS mandatory DESCRIPTION "The Data Link Connection Identifier for this DCP virtual circuit object." REFERENCE "Draft American National Standard T1.618-1991, Section 3.3.6" ::= { frDcpCircuitEntry 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.4.1.1.2 frDcpCircuitEnable OBJECT-TYPE SYNTAX INTEGER { on (1), off (2) -- default } ACCESS read-write STATUS mandatory DESCRIPTION "Indicates whether data compression should take place on this particular end side virtual circuit." DEFVAL { off } ::= { frDcpCircuitEntry 3 } -- 1.3.6.1.4.1.52.4.1.2.7.2.4.1.1.3 frDcpCircuitStatus OBJECT-TYPE SYNTAX INTEGER { on (1), off (2) } ACCESS read-only STATUS mandatory DESCRIPTION "On indicates that the compression has been successfully negotiated and is operating. Off indicates that the compression negotiation has failed and compression is not operating at this time, or compression has been terminated by either peer." ::= { frDcpCircuitEntry 4 } -- 1.3.6.1.4.1.52.4.1.2.7.2.4.1.1.4 frDcpCircuitRatio OBJECT-TYPE SYNTAX OCTET STRING (SIZE (5)) ACCESS read-only STATUS mandatory DESCRIPTION "The ratio of uncompressed to compressed transmitted data. If the data compression status is off, 1:1 will be displayed." ::= { frDcpCircuitEntry 5 } -- 1.3.6.1.4.1.52.4.1.2.7.2.4.1.1.5 -- Cabletron DDS Extensions Group -- This group is required for any platforms that have a dds physical port. ctDDSConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF CtDDSConfigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The DDS Configuration Table" ::= { ctDDSExt 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.5.1 ctDDSConfigEntry OBJECT-TYPE SYNTAX CtDDSConfigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An Entry in the DDS Configuration Table" INDEX { ctDDSLineIndex } ::= { ctDDSConfigTable 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1 CtDDSConfigEntry ::= SEQUENCE { ctDDSLineIndex INTEGER, ctDDSIfIndex INTEGER, ctDDSLineMode INTEGER, ctDDSLineCoding INTEGER, ctDDSLoopbackConfig INTEGER, ctDDSLineStatus INTEGER, ctDDSTxClockSource INTEGER, ctDDSPortInSpeed INTEGER, ctDDSPortOutSpeed INTEGER } ctDDSLineIndex OBJECT-TYPE SYNTAX INTEGER (1..'7fffffff'h) ACCESS read-only STATUS mandatory DESCRIPTION "A unique value for each ds1 physical port on the platform." ::= { ctDDSConfigEntry 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.1 ctDDSIfIndex OBJECT-TYPE SYNTAX INTEGER (1..'7fffffff'h) ACCESS read-only STATUS mandatory DESCRIPTION "Index associated with this dds physical port" ::= { ctDDSConfigEntry 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.2 ctDDSLineMode OBJECT-TYPE SYNTAX INTEGER { ddsPri (1), ddsSc (2), ddsCc (3) } ACCESS read-write STATUS mandatory DESCRIPTION "DDS-PRI is full duplex 56k link, No framing in loop data so loop speed is also 56k. Data stream: --d1 d2 d3 d4 d5 d6 d7-- DDS-SC is also full duplex 56k link, requires framing bits to distinguish between primary and secondary channels. --d1 d2 d3 d4 d5 d6 d7 F C/S-- where F is framing bit and C/S for secondary channel as well as used for control bit. With these two extra bits the loop speed is increased to 72k. primary channel rate is 56k. DDS-CC is full duplex 64k link. Does not require framing bit but uses a same format as SC, nineth bit position is lumped with primary channel and not used for control. Loop speed is 72k, Primary channel rate is 64k. --d1 d2 d3 d4 d5 d6 d7 F d8--" ::= { ctDDSConfigEntry 3 } -- 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.3 ctDDSLineCoding OBJECT-TYPE SYNTAX INTEGER { ddsNone (1), ddsJBZS (2), otherLineCode (3) } ACCESS read-write STATUS mandatory DESCRIPTION "This object describes the variety of Zero Code suppression on this interface. JBZS refers to Jammed Bit Zero suppresion, which forces a 1 bit every 8 bit periods. None refers to a mode in which some other means is used to insure pulse density requirements." ::= { ctDDSConfigEntry 4 } -- 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.4 ctDDSLoopbackConfig OBJECT-TYPE SYNTAX INTEGER { ddsNoLoop (1), ddsLocalLoop (2), ddsLineLoop (3), ddsOtherLoop (4) } ACCESS read-write STATUS mandatory DESCRIPTION "This variable represents the loopback configuration of the DDS interface. ddsNoLoop means the interface is not in loopback state, ddsLocalLoop means the signal is transmitted and looped back to the same interface, ddsLineLoop means the received signal at this interface does not go through the device but is looped back out, and ddsOtherLoop represents a loop not defined here." ::= { ctDDSConfigEntry 5 } -- 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.5 ctDDSLineStatus OBJECT-TYPE SYNTAX INTEGER { ddsNoAlarm (1), ddsLossOfSignal (2), ddsOutOfService (3), ddsOutOfFrame (4) } ACCESS read-only STATUS mandatory DESCRIPTION "This variable describes the current operational status of DDS line." ::= { ctDDSConfigEntry 6 } -- 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.6 ctDDSTxClockSource OBJECT-TYPE SYNTAX INTEGER { ddsLoopTiming (1), ddsLocalTiming (2), ddsThroughTiming (3) } ACCESS read-write STATUS mandatory DESCRIPTION "The source of Transmit clock. 'ddsLoopTiming' indicates that the recovered receive clock is used as transmit clock. 'ddsLocalTiming' indicates that a local clock source is used. 'ddsThroughTiming' indicates that recovered receive clock from another interface is used as transmit clock." ::= { ctDDSConfigEntry 7 } -- 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.7 ctDDSPortInSpeed OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION " This variable describes the current operational receive speed of DDS line. It is a read only value based entirely on DDS type (CC or PRI)." ::= { ctDDSConfigEntry 8 } -- 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.8 ctDDSPortOutSpeed OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This variable describes the current operational transmit speed of DDS line. It is a read only value based entirely on DDS type CC or PRI" ::= { ctDDSConfigEntry 9 } -- 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.9 -- -- Ctron PPP Counters Group. -- The following object reflect the values of the -- counters used for each PPP link. -- ctPppCountersIfIndex -- ctPppCountersMaxTerminate -- ctPppCountersMaxConfigure -- ctPppCountersMaxFailure -- ctPppCountersRestartTimer ctPppCountersTable OBJECT-TYPE SYNTAX SEQUENCE OF CtPppCountersEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table containing the parameters for the local PPP entity related to the counters and timers." ::= { ctPPPExt 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.1 ctPppCountersEntry OBJECT-TYPE SYNTAX CtPppCountersEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "PPP counter/timer information for a particular PPP link." INDEX { ctPppCountersIfIndex } ::= { ctPppCountersTable 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.1.1 CtPppCountersEntry ::= SEQUENCE { ctPppCountersIfIndex INTEGER, ctPppCountersMaxTerminate INTEGER, ctPppCountersMaxConfigure INTEGER, ctPppCountersMaxFailure INTEGER, ctPppCountersRestartTimer INTEGER } ctPppCountersIfIndex OBJECT-TYPE SYNTAX INTEGER(1..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "The ifIndex of the interface. This is the index of this entry in the ifTable." REFERENCE "rfc-1213" ::= { ctPppCountersEntry 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.1.1.1 ctPppCountersMaxTerminate OBJECT-TYPE SYNTAX INTEGER(1..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "MaxTerminate indicates the number of Terminate- Request packets sent without receiving a Terminate-Ack before assuming that the peer in unable to respond." ::= { ctPppCountersEntry 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.1.1.2 ctPppCountersMaxConfigure OBJECT-TYPE SYNTAX INTEGER(1..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "MaxConfigure indicates the number of Configure- Request packets sent without receiving a Configure-Ack, Configre-Nak or Configure-Reject before assuming that the peer in unable to respond." ::= { ctPppCountersEntry 3 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.1.1.3 ctPppCountersMaxFailure OBJECT-TYPE SYNTAX INTEGER(1..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "MaxFailure indicates the number of Configure-Nak packets sent without sending a Configure-Ack before assuming that the configuration is not converging. Any further Configure-Reject packets for peer requested options are converted to Configure-Reject packets, and locally desires options are no longer appended." ::= { ctPppCountersEntry 4 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.1.1.4 ctPppCountersRestartTimer OBJECT-TYPE SYNTAX INTEGER(1..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "The Restart timer is used to time transmissions of Configure-Request and Terminate-Request packets. Expiration of the Restart-Timer causes a Timeout event, and retransmission of the corresponding Configure-Request or Terminate-Request packet." ::= { ctPppCountersEntry 5 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.1.1.5 -- -- Ctron PPP LCP Extentions Group. -- The following object reflect the values of the -- LCP parameters not included in RFCs for this PPP link. -- -- ctPppLcpExtIfIndex -- ctPppLcpExtAuthenticationProt -- ctPppLcpExtQualityProt -- ctPppLcpExtPFC -- ctPppLcpExtACFC -- ctPppLcpExtSelfDescribePadding -- ctPppLcpExtCallback -- ctPppLcpExtCompoundFrames -- ctPppLcpExtMru -- ctPppLcpExtAccm -- ctPppLcpExtEchoRequest -- ctPppLcpExtReplyCounter -- ctPppLcpExtMpCapable ctPppLcpExtTable OBJECT-TYPE SYNTAX SEQUENCE OF CtPppLcpExtEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table containing the parameters for the local PPP entity related to the counters and timers." ::= { ctPPPExt 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.2 ctPppLcpExtEntry OBJECT-TYPE SYNTAX CtPppLcpExtEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "PPP LCP configurationinformation for a particular PPP link." INDEX { ctPppLcpExtIfIndex } ::= { ctPppLcpExtTable 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1 CtPppLcpExtEntry ::= SEQUENCE { ctPppLcpExtIfIndex INTEGER, ctPppLcpExtAuthenticationProt INTEGER, ctPppLcpExtQualityProt INTEGER, ctPppLcpExtPFC INTEGER, ctPppLcpExtACFC INTEGER, ctPppLcpExtSelfDescribePadding INTEGER, ctPppLcpExtCallback INTEGER, ctPppLcpExtCompoundFrames INTEGER, ctPppLcpExtMru INTEGER, ctPppLcpExtAccm INTEGER, ctPppLcpExtEchoRequest INTEGER, ctPppLcpExtReplyCounter INTEGER, ctPppLcpExtMpCapable INTEGER } ctPppLcpExtIfIndex OBJECT-TYPE SYNTAX INTEGER(1..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "The ifIndex of the interface. This is the index of this entry in the ifTable." REFERENCE "rfc-1213" ::= { ctPppLcpExtEntry 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.1 ctPppLcpExtAuthenticationProt OBJECT-TYPE SYNTAX INTEGER { none(1), pap(2), chap(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Enables a particular authentication protocol on this PPP link(now modified for read-only." ::= { ctPppLcpExtEntry 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.2 ctPppLcpExtQualityProt OBJECT-TYPE SYNTAX INTEGER { none(1), lqr(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enables a particular link-quality protocol on this PPP link." ::= { ctPppLcpExtEntry 3 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.3 ctPppLcpExtPFC OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enables protocol field compression on this PPP link." ::= { ctPppLcpExtEntry 4 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.4 ctPppLcpExtACFC OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enables address and control field compression on this PPP link." ::= { ctPppLcpExtEntry 5 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.5 ctPppLcpExtSelfDescribePadding OBJECT-TYPE SYNTAX INTEGER(1..256) ACCESS read-write STATUS mandatory DESCRIPTION "This Configuration Option provides a method for an implementation to indicate to the peer that it understands self-describing pads when padding is added at the end of the PPP Information field." ::= { ctPppLcpExtEntry 6 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.6 ctPppLcpExtCallback OBJECT-TYPE SYNTAX INTEGER(1..6) ACCESS read-write STATUS mandatory DESCRIPTION "This Configuration Option provides a method for an implementation to request a dial-up peer to call back." ::= { ctPppLcpExtEntry 7 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.7 ctPppLcpExtCompoundFrames OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This Configuration Option provides a method for an implementation to send multiple PPP encapsulated packets within the same frame." ::= { ctPppLcpExtEntry 8 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.8 ctPppLcpExtMru OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enables and disables Mru status." ::= { ctPppLcpExtEntry 9 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.9 ctPppLcpExtAccm OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enables and disables Accm status." ::= { ctPppLcpExtEntry 10 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.10 ctPppLcpExtEchoRequest OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "A zero indicated no Echo Request and any other value provides an interval to send Echo-Requests to the Peer. The Echo-Request provides a Data Link Layer loopback mechanism for use in exercising both directions of the link. This is useful in debugging, link quality determination. LCP MUST be in the OPENED state for an Echo-Request to occur." ::= { ctPppLcpExtEntry 11 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.11 ctPppLcpExtReplyCounter OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Increments a counter if the Local Device correctly received an Echo-Reply from the Peer. LCP MUST be in the OPENED state for an Echo-Reply to occur." ::= { ctPppLcpExtEntry 12 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.12 ctPppLcpExtMpCapable OBJECT-TYPE SYNTAX INTEGER{ enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Multilink Protocol (MP) option selector. Set to a value of one when MP support is desired otherwise set to a value of two. The default value is two. When set to two the attempt is made to negotiate MP support. MP support is symmetrical." ::= { ctPppLcpExtEntry 13 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.13 -- -- Ctron PPP BNCP Extentions Group. -- The following object reflect the values of the -- LCP parameters not included in RFCs for this PPP link. -- pppBncpExtIfIndex -- pppBncpExtCrcStatus ctPppBncpExtTable OBJECT-TYPE SYNTAX SEQUENCE OF CtPppBncpExtEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table containing the parameters for the local PPP entity related to the counters and timers." ::= { ctPPPExt 3 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.3 ctPppBncpExtEntry OBJECT-TYPE SYNTAX CtPppBncpExtEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "PPP LCP configuration information for a particular PPP link." INDEX { ctPppBncpExtIfIndex } ::= { ctPppBncpExtTable 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.3.1 CtPppBncpExtEntry ::= SEQUENCE { ctPppBncpExtIfIndex INTEGER, ctPppBncpExtCrcStatus INTEGER } ctPppBncpExtIfIndex OBJECT-TYPE SYNTAX INTEGER(1..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "The ifIndex of the interface. This is the index of this entry in the ifTable." REFERENCE "rfc-1213" ::= { ctPppBncpExtEntry 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.3.1.1 ctPppBncpExtCrcStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enables and disables CRC status. First our platform must support CRC. If the platform does, then setting to disabled will not send CRC. The default is enabled, which sends CRC." ::= { ctPppBncpExtEntry 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.3.1.2 -- Ctron PPP MP Extentions Group. -- The following object reflect the values of the -- LCP parameters not included in RFCs for this PPP link. -- ctPppMpExtIfIndex -- ctPppLcpExtMpLUT -- ctPppLcpExtMpHistoryTime -- ctPppLcpExtMpMoreBW -- ctPppLcpExtMpLessBW -- ctPppLcpExtMpMaxChannels -- ctPppLcpExtMpChannelsToAdd -- ctPppLcpExtMpChannelsToRemove ctPppMpExtTable OBJECT-TYPE SYNTAX SEQUENCE OF CtPppMpExtEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table containing the parameters for the local PPP entity related to the counters and timers." ::= { ctPPPExt 4 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.4 ctPppMpExtEntry OBJECT-TYPE SYNTAX CtPppMpExtEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "PPP LCP configurationinformation for a particular PPP link." INDEX { ctPppMpExtIfIndex } ::= { ctPppMpExtTable 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.4.1 CtPppMpExtEntry ::= SEQUENCE { ctPppMpExtIfIndex INTEGER, ctPppLcpExtMpLUT INTEGER, ctPppLcpExtMpHistoryTime INTEGER, ctPppLcpExtMpMoreBW INTEGER, ctPppLcpExtMpLessBW INTEGER, ctPppLcpExtMpMaxChannels INTEGER, ctPppLcpExtMpChannelsToAdd INTEGER, ctPppLcpExtMpChannelsToRemove INTEGER } ctPppMpExtIfIndex OBJECT-TYPE SYNTAX INTEGER(1..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "The ifIndex of the interface. This is the index of this entry in the ifTable." REFERENCE "rfc-1213" ::= { ctPppMpExtEntry 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.4.1.1 ctPppLcpExtMpLUT OBJECT-TYPE SYNTAX INTEGER (1..100) ACCESS read-write STATUS mandatory DESCRIPTION "Used to set the Line Utilization Threshold (LUT) % value to compare against the linear weighted percentage by which to determine when more/less bandwidth is to be added/removed. Linear weighting is averaged over the period of time specified by ctPppLcpExtMpHistoryTime." ::= { ctPppMpExtEntry 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.4.1.2 ctPppLcpExtMpHistoryTime OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-write STATUS mandatory DESCRIPTION "Used to set the history time value in seconds for the number of line utilization reading(s) desired to compute the average line utilization. That is to say, it specifies the window size over which to compute the average line utilization." ::= { ctPppMpExtEntry 3 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.4.1.3 ctPppLcpExtMpMoreBW OBJECT-TYPE SYNTAX INTEGER (1..255) ACCESS read-write STATUS mandatory DESCRIPTION "Used to set the number of consecutive line utilization average readings that must exceed ctPppLcpExtMpLUT as a condition of when to increase the bandwidth if more BW is permitted." ::= { ctPppMpExtEntry 4 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.4.1.4 ctPppLcpExtMpLessBW OBJECT-TYPE SYNTAX INTEGER (1..255) ACCESS read-write STATUS mandatory DESCRIPTION "Used to set the number of consecutive line utilization average readings that must fall below ctPppLcpExtMpLUT as a condition of when to remove possible previously added bandwidth." ::= { ctPppMpExtEntry 5 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.4.1.5 ctPppLcpExtMpMaxChannels OBJECT-TYPE SYNTAX INTEGER (1..255) ACCESS read-write STATUS mandatory DESCRIPTION "Used to set the maxium number of channels an MP capable connection is allowed." ::= { ctPppMpExtEntry 6 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.4.1.6 ctPppLcpExtMpChannelsToAdd OBJECT-TYPE SYNTAX INTEGER (1..255) ACCESS read-write STATUS mandatory DESCRIPTION "Used to set the number of additional channel(s) to increment by whenever the need for more bandwidth is determined." ::= { ctPppMpExtEntry 7 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.4.1.7 ctPppLcpExtMpChannelsToRemove OBJECT-TYPE SYNTAX INTEGER (1..255) ACCESS read-write STATUS mandatory DESCRIPTION "Used to set the number of channel(s) to decrement by whenever the need for possible previously added bandwidth is determined to no longer be needed." ::= { ctPppMpExtEntry 8 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.4.1.8 -- Ctron PPP ECP Extentions Group. -- The following object reflect the values of the -- ECP parameters not included in RFCs for this PPP link. ctPppEcpExtTable OBJECT-TYPE SYNTAX SEQUENCE OF CtPppEcpExtEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table containing the parameters for the local PPP entity related to the encrpytion control protocol." ::= { ctPPPExt 5 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.5 ctPppEcpExtEntry OBJECT-TYPE SYNTAX CtPppEcpExtEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "PPP ECP configuration information for a particular PPP link." INDEX { ctPppEcpExtIfIndex } ::= { ctPppEcpExtTable 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.5.1 CtPppEcpExtEntry ::= SEQUENCE { ctPppEcpExtIfIndex INTEGER, ctPppEcpKey DisplayString, ctPppEcpIV DisplayString } ctPppEcpExtIfIndex OBJECT-TYPE SYNTAX INTEGER(1..1024) ACCESS read-write STATUS mandatory DESCRIPTION "The ifIndex of the interface. This is the index of this entry in the ifTable." REFERENCE "rfc-1213" ::= { ctPppEcpExtEntry 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.5.1.1 ctPppEcpKey OBJECT-TYPE SYNTAX DisplayString (SIZE(14)) ACCESS read-write STATUS mandatory DESCRIPTION "A 56-bit key (14 hex characters) used for the DES encryption." ::= { ctPppEcpExtEntry 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.5.1.2 ctPppEcpIV OBJECT-TYPE SYNTAX DisplayString (SIZE(16)) ACCESS read-write STATUS mandatory DESCRIPTION "A 64-bit initialization vector (16 hex characters) used for the DES encryption in CBC mode." ::= { ctPppEcpExtEntry 3 } -- 1.3.6.1.4.1.52.4.1.2.7.2.6.5.1.3 -- ctWanalyzer Group -- This group is mandatory for all platforms which implement the -- WANalyzer -- ctWanalyzerIfIndex -- ctwanalyzerEnabled -- ctwanalyzerMaxEntries -- ctwanalyzerClearAll -- ctwanalyzerClearInterface -- ctwanalyzerDisplayInterface -- ctwanalyzerCurrEntries ctWanalyzerTable OBJECT-TYPE SYNTAX SEQUENCE OF CtWanalyzerEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table containing the parameters for the local Wanalyzer entity related to the configured Protocol." ::= { ctWanalyzer 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.7.1 ctWanalyzerEntry OBJECT-TYPE SYNTAX CtWanalyzerEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Information for a particular interface." INDEX { ctWanalyzerIfIndex } ::= { ctWanalyzerTable 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.7.1.1 CtWanalyzerEntry ::= SEQUENCE { ctWanalyzerIfIndex INTEGER, ctWanalyzerEnabled INTEGER, ctWanalyzerMaxEntries INTEGER, ctWanalyzerClearAll INTEGER, ctWanalyzerClearInterface INTEGER, ctWanalyzerDisplayInterface INTEGER, ctWanalyzerCurrEntries INTEGER } ctWanalyzerIfIndex OBJECT-TYPE SYNTAX INTEGER(1..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "The ifIndex of the interface. This is the index of this entry in the ifTable." REFERENCE "rfc-1213" ::= { ctWanalyzerEntry 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.7.1.1.1 ctWanalyzerEnabled OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This Persistent Object is a flag which indicates whether or not the WANalyzer is enabled or disabled. Upon system initialization this flag defaults to disabled unless a value for this object is found in NVRAM." ::= { ctWanalyzerEntry 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.7.1.1.2 ctWanalyzerMaxEntries OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This Persistent Object is an integer greater than 1 which specifies the maximum total number of entries which the table will handle. When the WANalyzer is enabled this value defaults to a value dependent on the implementation unless a value is found in NVRAM." ::= { ctWanalyzerEntry 3 } -- 1.3.6.1.4.1.52.4.1.2.7.2.7.1.1.3 ctWanalyzerClearAll OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "When set to 2, the entire table of entries is cleared. Upon clearing of the table, this value is reset to 1. This object is not present if the WANalyzer is disabled." ::= { ctWanalyzerEntry 4 } -- 1.3.6.1.4.1.52.4.1.2.7.2.7.1.1.4 ctWanalyzerClearInterface OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "When set to 2, all entries for this MIB-II interface index will be removed from the table. Upon complete removal of those entries, this value is reset to 1. This object is not present if the WANalyzer is disabled." ::= { ctWanalyzerEntry 5 } -- 1.3.6.1.4.1.52.4.1.2.7.2.7.1.1.5 ctWanalyzerDisplayInterface OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "When set to a valid MIB-II interface number, the table displays only those entries in the table which were received from that MIB-II interface. This value is set to -1 upon initialization and indicates that entries from all interfaces will be displayed. This object is not present if the WANalyzer is disabled." ::= { ctWanalyzerEntry 6 } -- 1.3.6.1.4.1.52.4.1.2.7.2.7.1.1.6 ctWanalyzerCurrEntries OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A non-negative integer indicating the current number of entries in the table. This object is not present if the WANalyzer is disabled." ::= { ctWanalyzerEntry 7 } -- 1.3.6.1.4.1.52.4.1.2.7.2.7.1.1.7 -- Ctron Wan Table Extentions Group. -- wanMessageIndex -- wanMessageInterfaceIndex -- wanMessageDate -- wanMessageTime -- wanMessageCode wanalyzerMessageTable OBJECT-TYPE SYNTAX SEQUENCE OF WanalyzerEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing all of the message entries for this device. If the WANalyzer is disabled, this table will not be present." ::= { ctWanalyzer 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.7.2 wanalyzerEntry OBJECT-TYPE SYNTAX WanalyzerEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A message entry in the WANalyzer table corresponding to a particular interface in a particular instance." INDEX { wanMessageIndex } ::= { wanalyzerMessageTable 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.7.2.1 WanalyzerEntry ::= SEQUENCE { wanMessageIndex INTEGER, wanMessageInterfaceIndex INTEGER, wanMessageDate DisplayString, wanMessageTime DisplayString, wanMessageCode INTEGER } wanMessageIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "An integer between 1 and wanalyzerMaxEntries which indicates the overall position this entry has in the WANalyzer table." ::= { wanalyzerEntry 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.7.2.1.1 wanMessageInterfaceIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The MIB-II interface index representing the interface which sent this message." ::= { wanalyzerEntry 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.7.2.1.2 wanMessageDate OBJECT-TYPE SYNTAX DisplayString (SIZE(8)) ACCESS read-only STATUS mandatory DESCRIPTION "The date when this message was received by the WANalyzer in the standard MMDDYY format." ::= { wanalyzerEntry 3 } -- 1.3.6.1.4.1.52.4.1.2.7.2.7.2.1.3 wanMessageTime OBJECT-TYPE SYNTAX DisplayString (SIZE(6)) ACCESS read-only STATUS mandatory DESCRIPTION "The time of day when this message was received by the WANalyzer in the standard HHMMSS format." ::= { wanalyzerEntry 4 } -- 1.3.6.1.4.1.52.4.1.2.7.2.7.2.1.4 wanMessageCode OBJECT-TYPE SYNTAX INTEGER { wanalyzerLastMessageRepeated(1), pppAuthentication(2), pppBncpThisLayerStart(3), pppBncpThisLayerFinished(4), pppBncpThisLayerUp(5), pppBncpThisLayerDown(6), pppBncpInitializeRestartCount(7), pppBncpZeroRestartCount(8), pppBncpRcvConfReqGood(9), pppBncpRcvConfReqBad(10), pppBncpReceiveConfigureAck(11), pppBncpReceiveConfigureNak(12), pppBncpReceiveConfigureReject(13), pppBncpReceiveTerminateRequest(14), pppBncpReceiveTerminateAck(15), pppBncpReceiveCodeRejectPermitted(16), pppBncpReceiveCodeRejectCatastrophic(17), pppBncpReceiveProtocolRejectPermitted(18), pppBncpReceiveEchoRequest(19), pppBncpReceiveEchoReply(20), pppBncpReceiveDiscardRequest(21), pppBncpReceiveUnknownCode(22), pppBncpIllegalAction(23), pppBncpSendConfigureRequest(24), pppBncpSendConfigureAck(25), pppBncpSendConfigureNak(26), pppBncpSendConfigureReject(27), pppBncpSendTerminateRequest(28), pppBncpSendTerminateAck(29), pppBncpSendCodeReject(30), pppBncpSendProtocolReject(31), pppBncpSendEchoReply(32), pppBncpInitialState(33), pppBncpStartingState(34), pppBncpClosedState(35), pppBncpStoppedState(36), pppBncpClosingState(37), pppBncpStoppingState(38), pppBncpReqSentState(39), pppBncpAckRcvdState(40), pppBncpAckSentState(41), pppBncpOpenedState(42), pppBncpEthernetMacType(43), pppBncpTokenRingMacType(44), pppBncpFddiMacType(45), pppBncpBridgeIdRcvReq(46), pppBncpBridgeIdRcvNak(47), pppBncpBridgeIdRcvRej(48), pppBncpBridgeIdXmitReq(49), pppBncpMacSelectRcvReq(50), pppBncpMacSelectRcvNak(51), pppBncpMacSelectRcvRej(52), pppBncpMacSelectXmitReq(53), pppBncpTinygramRcvReq(54), pppBncpTinygramRcvNak(55), pppBncpTinygramRcvRej(56), pppBncpTinygramXmitReq(57), pppBncpLanIdRcvReq(58), pppBncpLanIdRcvNak(59), pppBncpLanIdRcvRej(60), pppBncpLanIdXmitReq(61), pppCcpThisLayerStart(62), pppCcpThisLayerFinished(63), pppCcpThisLayerUp(64), pppCcpThisLayerDown(65), pppCcpInitializeRestartCount(66), pppCcpZeroRestartCount(67), pppCcpRcvConfReqGood(68), pppCcpRcvConfReqBad(69), pppCcpReceiveConfigureAck(70), pppCcpReceiveConfigureNak(71), pppCcpReceiveConfigureReject(72), pppCcpReceiveTerminateRequest(73), pppCcpReceiveTerminateAck(74), pppCcpReceiveCodeRejectPermitted(75), pppCcpReceiveCodeRejectCatastrophic(76), pppCcpReceiveProtocolRejectPermitted(77), pppCcpReceiveEchoRequest(78), pppCcpReceiveEchoReply(79), pppCcpReceiveDiscardRequest(80), pppCcpReceiveUnknownCode(81), pppCcpIllegalAction(82), pppCcpSendConfigureRequest(83), pppCcpSendConfigureAck(84), pppCcpSendConfigureNak(85), pppCcpSendConfigureReject(86), pppCcpSendTerminateRequest(87), pppCcpSendTerminateAck(88), pppCcpSendCodeReject(89), pppCcpSendProtocolReject(90), pppCcpSendEchoReply(91), pppCcpInitialState(92), pppCcpStartingState(93), pppCcpClosedState(94), pppCcpStoppedState(95), pppCcpClosingState(96), pppCcpStoppingState(97), pppCcpReqSentState(98), pppCcpAckRcvdState(99), pppCcpAckSentState(100), pppCcpOpenedState(101), pppCcpProprietaryCompRcvReq(102), pppCcpProprietaryCompRcvNak(103), pppCcpProprietaryCompRcvRej(104), pppCcpProprietaryCompXmitReq(105), pppCcpPredictorType1RcvReq(106), pppCcpPredictorType1RcvNak(107), pppCcpPredictorType1RcvRej(108), pppCcpPredictorType1XmitReq(109), pppCcpPredictorType2RcvReq(110), pppCcpPredictorType2RcvNak(111), pppCcpPredictorType2RcvRej(112), pppCcpPredictorType2XmitReq(113), pppCcpPuddleJumperRcvReq(114), pppCcpPuddleJumperRcvNak(115), pppCcpPuddleJumperRcvRej(116), pppCcpPuddleJumperXmitReq(117), pppCcpHpPpcRcvReq(118), pppCcpHpPpcRcvNak(119), pppCcpHpPpcRcvRej(120), pppCcpHpPpcXmitReq(121), pppCcpStacLzsRcvReq(122), pppCcpStacLzsRcvNak(123), pppCcpStacLzsRcvRej(124), pppCcpStacLzsXmitReq(125), pppCcpMsPpcRcvReq(126), pppCcpMsPpcRcvNak(127), pppCcpMsPpcRcvRej(128), pppCcpMsPpcXmitReq(129), pppCcpGandalfFzaRcvReq(130), pppCcpGandalfFzaRcvNak(131), pppCcpGandalfFzaRcvRej(132), pppCcpGandalfFzaXmitReq(133), pppCcpV42bisRcvReq(134), pppCcpV42bisRcvNak(135), pppCcpV42bisRcvRej(136), pppCcpV42bisXmitReq(137), pppCcpBsdLzwRcvReq(138), pppCcpBsdLzwRcvNak(139), pppCcpBsdLzwRcvRej(140), pppCcpBsdLzwXmitReq(141), pppCcpStackDcpRcvReq(142), pppCcpStackDcpRcvNak(143), pppCcpStackDcpRcvRej(144), pppCcpStackDcpXmitReq(145), pppChapChallengeReceived(146), pppChapResponseReceived(147), pppChapSuccessReceived(148), pppChapFailureReceived(149), pppChapSuccessSent(150), pppChapFailureSent(151), pppChapChallengeSent(152), pppChapResponseSent(153), pppIpcpThisLayerStart(154), pppIpcpThisLayerFinished(155), pppIpcpThisLayerUp(156), pppIpcpThisLayerDown(157), pppIpcpInitializeRestartCount(158), pppIpcpZeroRestartCount(159), pppIpcpRcvConfReqGood(160), pppIpcpRcvConfReqBad(161), pppIpcpReceiveConfigureAck(162), pppIpcpReceiveConfigureNak(163), pppIpcpReceiveConfigureReject(164), pppIpcpReceiveTerminateRequest(165), pppIpcpReceiveTerminateAck(166), pppIpcpReceiveCodeRejectPermitted(167), pppIpcpReceiveCodeRejectCatastrophic(168), pppIpcpReceiveProtocolRejectPermitted(169), pppIpcpReceiveEchoRequest(170), pppIpcpReceiveEchoReply(171), pppIpcpReceiveDiscardRequest(172), pppIpcpReceiveUnknownCode(173), pppIpcpIllegalAction(174), pppIpcpSendConfigureRequest(175), pppIpcpSendConfigureAck(176), pppIpcpSendConfigureNak(177), pppIpcpSendConfigureReject(178), pppIpcpSendTerminateRequest(179), pppIpcpSendTerminateAck(180), pppIpcpSendCodeReject(181), pppIpcpSendProtocolReject(182), pppIpcpSendEchoReply(183), pppIpcpInitialState(184), pppIpcpStartingState(185), pppIpcpClosedState(186), pppIpcpStoppedState(187), pppIpcpClosingState(188), pppIpcpStoppingState(189), pppIpcpReqSentState(190), pppIpcpAckRcvdState(191), pppIpcpAckSentState(192), pppIpcpOpenedState(193), pppIpcpIpAddressRcvReq(194), pppIpcpIpAddressRcvNak(195), pppIpcpIpAddressRcvRej(196), pppIpcpIpAddressXmitReq(197), pppIpcpCompressionTypeRcvReq(198), pppIpcpCompressionTypeRcvRej(199), pppIpcpCompressionTypeRcvNak(200), pppIpcpCompressionTypeXmitReq(201), pppIpxcpThisLayerStart(202), pppIpxcpThisLayerFinished(203), pppIpxcpThisLayerUp(204), pppIpxcpThisLayerDown(205), pppIpxcpInitializeRestartCount(206), pppIpxcpZeroRestartCount(207), pppIpxcpRcvConfReqGood(208), pppIpxcpRcvConfReqBad(209), pppIpxcpReceiveConfigureAck(210), pppIpxcpReceiveConfigureNak(211), pppIpxcpReceiveConfigureReject(212), pppIpxcpReceiveTerminateAck(214), pppIpxcpReceiveCodeRejectPermitted(215), pppIpxcpReceiveCodeRejectCatastrophic(216), pppIpxcpReceiveProtocolRejectPermitted(217), pppIpxcpReceiveEchoRequest(218), pppIpxcpReceiveEchoReply(219), pppIpxcpReceiveDiscardRequest(220), pppIpxcpReceiveUnknownCode(221), pppIpxcpIllegalAction(222), pppIpxcpSendConfigureRequest(223), pppIpxcpSendConfigureAck(224), pppIpxcpSendConfigureNak(225), pppIpxcpSendConfigureReject(226), pppIpxcpSendTerminateRequest(227), pppIpxcpSendTerminateAck(228), pppIpxcpSendCodeReject(229), pppIpxcpSendProtocolReject(230), pppIpxcpSendEchoReply(231), pppIpxcpInitialState(232), pppIpxcpStartingState(233), pppIpxcpClosedState(234), pppIpxcpStoppedState(235), pppIpxcpClosingState(236), pppIpxcpStoppingState(237), pppIpxcpReqSentState(238), pppIpxcpAckRcvdState(239), pppIpxcpAckSentState(240), pppIpxcpOpenedState(241), pppIpxcpCompressionProtocolRcvReq(242), pppIpxcpCompressionProtocolRcvNak(243), pppIpxcpCompressionProtocolRcvRej(244), pppIpxcpCompressionProtocolXmitReq(245), pppIpxcpNetworkNumberRcvReq(246), pppIpxcpNetworkNumberRcvNak(247), pppIpxcpNetworkNumberRcvRej(248), pppIpxcpNetworkNumberXmitReq(249), pppIpxcpNodeNumberRcvReq(250), pppIpxcpNodeNumberRcvNak(251), pppIpxcpNodeNumberRcvRej(252), pppIpxcpNodeNumberXmitReq(253), pppIpxcpRoutingProtocolRcvReq(254), pppIpxcpRoutingProtocolRcvNak(255), pppIpxcpRoutingProtocolRcvRej(256), pppIpxcpRoutingProtocolXmitReq(257), pppIpxcpRouterNameRcvReq(258), pppIpxcpRouterNameRcvNak(259), pppIpxcpRouterNameRcvRej(260), pppIpxcpRouterNameXmitReq(261), pppIpxcpConfigurationCompleteRcvReq(262), pppIpxcpConfigurationCompleteRcvNak(263), pppIpxcpConfigurationCompleteRcvRej(264), pppIpxcpConfigurationCompleteXmitReq(265), pppLcpThisLayerStart(266), pppLcpThisLayerFinished(267), pppLcpThisLayerUp(268), pppLcpThisLayerDown(269), pppLcpInitializeRestartCount(270), pppLcpZeroRestartCount(271), pppLcpRcvConfReqGood(272), pppLcpRcvConfReqBad(273), pppLcpReceiveConfigureAck(274), pppLcpReceiveConfigureNak(275), pppLcpReceiveConfigureReject(276), pppLcpReceiveTerminateRequest(277), pppLcpReceiveTerminateAck(278), pppLcpReceiveCodeRejectPermitted(279), pppLcpReceiveCodeRejectCatastrophic(280), pppLcpReceiveProtocolReject(281), pppLcpReceiveEchoRequest(282), pppLcpReceiveEchoReply(283), pppLcpReceiveDiscardRequest(284), pppLcpReceiveUnknownCode(285), pppLcpIllegalAction(286), pppLcpSendConfigureRequest(287), pppLcpSendConfigureAck(288), pppLcpSendConfigureNak(289), pppLcpSendConfigureReject(290), pppLcpSendTerminateRequest(291), pppLcpSendTerminateAck(292), pppLcpSendCodeReject(293), pppLcpSendProtocolReject(294), pppLcpSendEchoReply(295), pppLcpInitialState(296), pppLcpStartingState(297), pppLcpClosedState(298), pppLcpStoppedState(299), pppLcpClosingState(300), pppLcpStoppingState(301), pppLcpReqSentState(302), pppLcpAckRcvdState(303), pppLcpAckSentState(304), pppLcpOpenedState(305), pppLcpMruRcvReq(306), pppLcpMruRcvNak(307), pppLcpMruRcvRej(308), pppLcpMruXmitReq(309), pppLcpAsyncCharMapRcvReq(310), pppLcpAsyncCharMapRcvNak(311), pppLcpAsyncCharMapRcvRej(312), pppLcpAsyncCharMapXmitReq(313), pppLcpAuthenticationRcvReq(314), pppLcpAuthenticationRcvNak(315), pppLcpAuthenticationRcvRej(316), pppLcpAuthenticationXmitReq(317), pppLcpMagicNumberRcvReq(318), pppLcpMagicNumberRcvNak(319), pppLcpMagicNumberRcvRej(320), pppLcpMagicNumberXmitReq(321), pppLcpLinkQualityRcvReq(322), pppLcpLinkQualityRcvNak(323), pppLcpLinkQualityRcvRej(324), pppLcpLinkQualityXmitReq(325), pppLcpProtCompRcvReq(326), pppLcpProtCompRcvNak(327), pppLcpProtCompRcvRej(328), pppLcpProtCompXmitReq(329), pppLcpAddrCompRcvReq(330), pppLcpAddrCompRcvNak(331), pppLcpAddrCompRcvRej(332), pppLcpAddrCompXmitReq(333), pppLcpFcs32BitRcvReq(334), pppLcpFcs32BitRcvNak(335), pppLcpFcs32BitRcvRej(336), pppLcpFcs32BitXmitReq(337), pppLcpSelfDescPaddingRcvReq(338), pppLcpSelfDescPaddingRcvNak(339), pppLcpSelfDescPaddingRcvRej(340), pppLcpSelfDescPaddingXmitReq(341), pppLcpCompoundFramesRcvReq(342), pppLcpCompoundFramesRcvNak(343), pppLcpCompoundFramesRcvRej(344), pppLcpCompoundFramesXmitReq(345), pppLcpCallbackRcvReq(346), pppLcpCallbackRcvNak(347), pppLcpCallbackRcvRej(348), pppLcpCallbackXmitReq(349), pppLexThisLayerStart(350), pppLexThisLayerFinished(351), pppLexThisLayerUp(352), pppLexThisLayerDown(353), pppLexInitializeRestartCount(354), pppLexZeroRestartCount(355), pppLexRcvConfReqGood(356), pppLexRcvConfReqBad(357), pppLexReceiveConfigureAck(358), pppLexReceiveConfigureNak(359), pppLexReceiveConfigureReject(360), pppLexReceiveTerminateRequest(361), pppLexReceiveTerminateAck(362), pppLexReceiveCodeRejectPermitted(363), pppLexReceiveCodeRejectCatastrophic(364), pppLexReceiveProtocolRejectPermitted(365), pppLexReceiveEchoRequest(366), pppLexReceiveEchoReply(367), pppLexReceiveDiscardRequest(368), pppLexReceiveUnknownCode(369), pppLexIllegalAction(370), pppLexSendConfigureRequest(371), pppLexSendConfigureAck(372), pppLexSendConfigureNak(373), pppLexSendConfigureReject(374), pppLexSendTerminateRequest(375), pppLexSendTerminateAck(376), pppLexSendCodeReject(377), pppLexSendProtocolReject(378), pppLexSendEchoReply(379), pppLexInitialState(380), pppLexStartingState(381), pppLexClosedState(382), pppLexStoppedState(383), pppLexClosingState(384), pppLexStoppingState(385), pppLexReqSentState(386), pppLexAckRcvdState(387), pppLexAckSentState(388), pppLexOpenedState(389), pppLexMacTypeSelectRcvReq(390), pppLexMacTypeSelectRcvNak(391), pppLexMacTypeSelectRcvRej(392), pppLexMacTypeSelectXmitReq(393), pppLexTinygramCompressRcvReq(394), pppLexTinygramCompressRcvNak(395), pppLexTinygramCompressRcvRej(396), pppLexTinygramCompressXmitReq(397), pppLexMacAddressRcvReq(398), pppLexMacAddressRcvNak(399), pppLexMacAddressRcvRej(400), pppLexMacAddressXmitReq(401), pppLexMacRelayRcvReq(402), pppLexMacRelayRcvNak(403), pppLexMacRelayRcvRej(404), pppLexMacRelayXmitReq(405), pppLexStatisticsRequestRcvReq(406), pppLqrSent(407), pppLqrReceived(408), pppLinkDead(409), pppLinkEstablishment(410), pppLinkTermination(411), pppNetworkLayerPhase(412), pppPapAuthenticateReqReceived(413), pppPapAuthenticateAckReceived(414), pppPapAuthenticateNakReceived(415), pppPapAuthenticateReqSent(416), pppPapAuthenticateAckSent(417), pppPapAuthenticateNakSent(418), frGotLmiPacket(500), frGotBadQ922Header(501), frGotCllmPacket(502), frInactiveReceivedPacket(503), frReceivedNlpidIpPacket(504), frSentXidPacket(505), frSentXidResponse(506), frReceivedXidPacket(507), frXidTimerExpired(508), frGotBadUi(509), frGotBadSnapPacket(510), frLinkUp(511), frLinkDown(512), frLmiStarted(513), frLmiStopped(514), frLmiSentFullStatusEnquiry(515), frLmiSentKeepAliveMessage(516), frLmiStatusResponseReceived(517), frLmiGotAnsiReportType(518), frLmiGotFullStatusReport(519), frLmiGotKeepAliveMessage(520), frLmiUnsolicitedKeepAlive(521), frLmiAsynchronousStatus(522), frLmiGotQ933AReportType(523), frLmiBadPvcStatusLength(524), frLmiT391TimeoutFs(525), frLmiT391TimeoutSe(526), frLmiT391PollFailed(527), frLmiT391PollSucceeded(528), frLmiStatusEnquiryReceived(529), frDcpMode1Initializing(530), frDcpMode1Disabled(531), frDcpMode1ControlPacketReceived(532), frDcpMode1DataPacketReceived(533), frDcpMode1RequestSent(534), frDcpMode1RequestReceived(535), frDcpMode1ResponseSent(536), frDcpMode1ResponseReceived(537), frDcpMode1Operational(538), frDcpMode1TimerExpired(539), frDcpMode2ControlPacketReceived(540), frDcpResetPacketSent(541), frDcpResetTimerExpired(542), frDcpResetAckSent(543), frDcpDictionaryQuotaExceeded(544), isdnRemoteConnectionUp(1000), isdnRemoteConnectionDown(1001), isdnActivateConnection(1002), isdnDeactivateConnection(1003), multilinkMpLinkUp(1500), multilinkMpAddBW(1501), multilinkMpRemoveBW(1502), multilinkMpSentBeginningFragment(1503), multilinkMpSentMiddleFragment(1504), multilinkMpSentEndFragment(1505), multilinkMpSentCompleteMessage(1506), multilinkMpReceivedBeginningFragment(1507), multilinkMpReceivedMiddleFragment(1508), multilinkMpReceivedEndFragment(1509), multilinkMpReceivedCompleteMessage(1510) } ACCESS read-only STATUS mandatory DESCRIPTION "An enumerated value representing the nature of the debug message sent by the interface." ::= { wanalyzerEntry 5 } -- 1.3.6.1.4.1.52.4.1.2.7.2.7.2.1.5 -- -- Wan Alarms Group -- This group is required for any platforms that support -- Cabletron's WAN Alarm processing functionality -- -- -- DS1 Alarms Global Configuration Variables -- -- These parameters apply globally to the DS1 Alarms -- entity. These variables allow the user to program -- DS1 alarm characteristics to be the same for all DS1 -- lines installed in the device. The other option -- available to the user would be to configure each DS1 -- line individually, using the parameters in the DS1 -- Alarms Configuration Table. -- ds1AlarmsGlobalConfigGroup OBJECT IDENTIFIER ::= { ctDs1Alarms 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.8.1 ds1AlarmGlobalAdmin OBJECT-TYPE SYNTAX INTEGER { disabled(1), -- default enabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Used to enable and disable the DS1 Alarm Monitoring Application for all DS1 circuits on the device." ::= { ds1AlarmsGlobalConfigGroup 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.8.1.1 ds1AlarmGlobalAutoRecovery OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2) -- default } ACCESS read-write STATUS mandatory DESCRIPTION "Used to enable and disable the DS1 Alarm Automatic Recovery feature for all DS1 circuits on the device. For those devices that support ds1 alarm monitoring, but do not support the automatic recovery feature, this object always returns disabled, and performs no action when written." ::= { ds1AlarmsGlobalConfigGroup 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.8.1.2 ds1AlarmGlobalTrapEnable OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2) -- default } ACCESS read-write STATUS mandatory DESCRIPTION "Used to enable and disable the DS1 Alarm SNMP Trap generation feature for all DS1 circuits on the device. This object operates in conjunction with configuration of objects in the ctron-trap-mib.txt" ::= { ds1AlarmsGlobalConfigGroup 3 } -- 1.3.6.1.4.1.52.4.1.2.7.2.8.1.3 ds1AlarmGlobalESCount OBJECT-TYPE SYNTAX INTEGER (1..300) -- default is 100 ACCESS read-write STATUS mandatory DESCRIPTION "Used in conjuction with ctDs1AlarmESInterval to set the threshold for alarm generation when the number of Errored Seconds for a specified time interval, measured in minutes, is exceeded. The default Errored Seconds alarm condition is 100 errored seconds over a 6 minute time interval." ::= { ds1AlarmsGlobalConfigGroup 4 } -- 1.3.6.1.4.1.52.4.1.2.7.2.8.1.4 ds1AlarmGlobalESInterval OBJECT-TYPE SYNTAX INTEGER (1..15) -- default is 6 minutes ACCESS read-write STATUS mandatory DESCRIPTION "Used in conjuction with ds1AlarmGlobalESCount to set the threshold for alarm generation when the number of Errored Seconds for a specified time interval, measured in minutes, is exceeded. The default Errored Seconds alarm condition is 100 errored seconds over a 6 minute time interval." ::= { ds1AlarmsGlobalConfigGroup 5 } -- 1.3.6.1.4.1.52.4.1.2.7.2.8.1.5 ds1AlarmGlobalBPVErrorRate OBJECT-TYPE SYNTAX INTEGER (5..9) -- default is 6 ACCESS read-write STATUS mandatory DESCRIPTION "Used to specify the negative exponent of 10, used in monitoring Bipolar Violations (Code Violations for E1) over intervals defined by ds1AlarmGlobalBPVInterval. For example, for a ds1AlarmGlobalBPVErrorRate value of 6 used with a ds1AlarmGlobalBPVInterval of 15, an alarm is generated when a 15 minute period has an average error rate which exceeds 1 Bipolar Violation (Code Violation for E1) per million bits. For those devices that support ds1 alarm monitoring but who's hardware does not support detect bipolar violations, this object always returns the default, and performs no action when written." ::= { ds1AlarmsGlobalConfigGroup 6 } -- 1.3.6.1.4.1.52.4.1.2.7.2.8.1.6 ds1AlarmGlobalBPVInterval OBJECT-TYPE SYNTAX INTEGER (1..15) -- default is 15 minutes ACCESS read-write STATUS mandatory DESCRIPTION "Used to specify the interval, used in monitoring Bipolar Violations (Code Violations for E1) with thresholds defined by ds1AlarmGlobalBPVErrorRate. For example, for a ds1AlarmGlobalBPVErrorRate value of 6 used with a ds1AlarmGlobalBPVInterval of 15, an alarm is generated when a 15 minute period has an average error rate which exceeds 1 Bipolar Violation (Code Violation for E1) per million bits. For those devices that support ds1 alarm monitoring but who's hardware does not detect bipolar violations, this object always returns the default, and performs no action when written." ::= { ds1AlarmsGlobalConfigGroup 7 } -- 1.3.6.1.4.1.52.4.1.2.7.2.8.1.7 ds1AlarmGlobalManualRecovery OBJECT-TYPE SYNTAX INTEGER { recover(1) } ACCESS read-write STATUS mandatory DESCRIPTION "To cause a manual recovery to occur on all Ds1 circuits, this object is set to a 1. It is always read as a 1. The recovery will occur only when automatic recovery is disabled." ::= { ds1AlarmsGlobalConfigGroup 8 } -- 1.3.6.1.4.1.52.4.1.2.7.2.8.1.8 -- -- DS1 Alarms Configuration Table -- -- The DS1 alarm table structure contains the same information as the -- global configuration objects, but allows seperate configuratoin of -- specific DS1 circuits contained on the device -- ds1AlarmConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF Ds1AlarmConfigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table containing objects used to configure DS1 alarm functionality on a per DS1 basis." ::= { ctDs1Alarms 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.8.2 ds1AlarmConfigEntry OBJECT-TYPE SYNTAX Ds1AlarmConfigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A description of a single entry." INDEX { ds1PhysNum } ::= { ds1AlarmConfigTable 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1 Ds1AlarmConfigEntry ::= SEQUENCE { ds1PhysNum INTEGER, ds1AlarmAdmin INTEGER, ds1AlarmAutoRecovery INTEGER, ds1AlarmTrapEnable INTEGER, ds1AlarmESCount INTEGER, ds1AlarmESInterval INTEGER, ds1AlarmBPVErrorRate INTEGER, ds1AlarmBPVInterval INTEGER, ds1AlarmManualRecovery INTEGER } ds1PhysNum OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The value for this object is equal to the value of a unique physical connection identifier associated with this DS1 which is clearly labeled on the device. For those products that do not have a DS1 identifier labeled on the device, the value for this object is the same as rfc1406 dsx1LineIndex." ::= { ds1AlarmConfigEntry 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1.1 ds1AlarmAdmin OBJECT-TYPE SYNTAX INTEGER { disabled(1), -- default enabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Used to enable and disable the DS1 Alarm Monitoring Application for this DS1 circuit." ::= { ds1AlarmConfigEntry 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1.2 ds1AlarmAutoRecovery OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2) -- default } ACCESS read-write STATUS mandatory DESCRIPTION "Used to enable and disable the DS1 Alarm Automatic Recovery feature for this DS1 circuit. For those devices that support ds1 alarm monitoring, but do not support the automatic recovery feature, this object always returns disabled, and performs no action when written." ::= { ds1AlarmConfigEntry 3 } -- 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1.3 ds1AlarmTrapEnable OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2) -- default } ACCESS read-write STATUS mandatory DESCRIPTION "Used to enable and disable the DS1 Alarm SNMP Trap generation feature for this DS1 circuit. This object operates in conjunction with configuration of objects in the ctron-trap-mib.txt" ::= { ds1AlarmConfigEntry 4 } -- 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1.4 ds1AlarmESCount OBJECT-TYPE SYNTAX INTEGER (1..300) -- default is 100 ACCESS read-write STATUS mandatory DESCRIPTION "Used in conjuction with ctDs1AlarmESInterval to set the threshold for alarm generation when the number of Errored Seconds for a specified time interval, measured in minutes, is exceeded. The default Errored Seconds alarm condition is 100 errored seconds over a 6 minute time interval." ::= { ds1AlarmConfigEntry 5 } -- 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1.5 ds1AlarmESInterval OBJECT-TYPE SYNTAX INTEGER (1..15) -- default is 6 minutes ACCESS read-write STATUS mandatory DESCRIPTION "Used in conjuction with ctDs1AlarmESCount to set the threshold for alarm generation when the number of Errored Seconds for a specified time interval, measured in minutes, is exceeded. The default Errored Seconds alarm condition is 100 errored seconds over a 6 minute time interval." ::= { ds1AlarmConfigEntry 6 } -- 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1.6 ds1AlarmBPVErrorRate OBJECT-TYPE SYNTAX INTEGER (5..9) -- default is 6 ACCESS read-write STATUS mandatory DESCRIPTION "Used to specify the negative exponent of 10, used in monitoring Bipolar Violations (Code Violations for E1) over intervals defined by ds1AlarmBPVInterval. For example, for a ds1AlarmBPVErrorRate value of 6 used with a ds1AlarmBPVInterval of 15, an alarm is generated when a 15 minute period has an average error rate which exceeds 1 Bipolar Violation (Code Violation for E1) per million bits. For those devices that support ds1 alarm monitoring but who's hardware does not support detect bipolar violations, this object always returns the default, and performs no action when written." ::= { ds1AlarmConfigEntry 7 } -- 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1.7 ds1AlarmBPVInterval OBJECT-TYPE SYNTAX INTEGER (1..15) -- default is 15 minutes ACCESS read-write STATUS mandatory DESCRIPTION "Used to specify the interval, used in monitoring Bipolar Violations (Code Violations for E1) with thresholds defined by ds1AlarmBPVErrorRate. For example, for a ds1AlarmBPVErrorRate value of 6 used with a ds1AlarmBPVInterval of 15, an alarm is generated when a 15 minute period has an average error rate which exceeds 1 Bipolar Violation (Code Violation for E1) per million bits. For those devices that support ds1 alarm monitoring but who's hardware does not support detect bipolar violations, this object always returns the default, and performs no action when written." ::= { ds1AlarmConfigEntry 8 } -- 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1.8 ds1AlarmManualRecovery OBJECT-TYPE SYNTAX INTEGER { recover(1) } ACCESS read-write STATUS mandatory DESCRIPTION "To cause a manual recovery to occur, this object is set to a 1. It is always read as a 1. The recovery will occur only when automatic recovery is disabled." ::= { ds1AlarmConfigEntry 9 } -- 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1.9 -- -- Wan Internet Protocol Priority Queue Filters Group -- This group is required for any platforms that support -- Cabletron's WAN IP Priority Queue processing functionality -- -- -- IP PQ Configuration Variables -- -- These parameters apply to the IP Priority Queue -- entity. These variables allow the user to program -- IP addresses in a filtering database. The database -- of IP addresses are used when a WAN service is over -- subscribed, and the packet would normally be discarded. -- If the IP PQ admin status is enabled, and the IP -- address of the packet to be discarded matches one -- programmed in the database, an attempt will be made -- to use high priority, reserved, resources to transmit -- the packet. The addresses programmed in this table -- should be reserved for those packets which MUST be -- transmitted. Some examples would be RIP, and SNMP -- packets, who's loss would cause major networking -- problems for the system. -- ipPQConfigGroup OBJECT IDENTIFIER ::= { ctIPPQFilters 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.9.1 ipPQAdmin OBJECT-TYPE SYNTAX INTEGER { disabled(1), -- default enabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Used to enable and disable the IP Priority Queue Forwarding Application." ::= { ipPQConfigGroup 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.9.1.1 iPPQMaxEntries OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns the maximum number of IP address entries supported by the IP Priority Queue application on this device." ::= { ipPQConfigGroup 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.9.1.2 iPPQNumEntries OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Get the number of IP address entries currently programmed in the ipPQAddressTable." ::= { ipPQConfigGroup 3 } -- 1.3.6.1.4.1.52.4.1.2.7.2.9.1.3 iPPQAddAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "Add an IP address to the ipPQAddressTable. Always read as a 0.0.0.0." ::= { ipPQConfigGroup 4 } -- 1.3.6.1.4.1.52.4.1.2.7.2.9.1.4 iPPQDelAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "Delete an IP address from the ipPQAddressTable. Always read as a 0.0.0.0." ::= { ipPQConfigGroup 5 } -- 1.3.6.1.4.1.52.4.1.2.7.2.9.1.5 -- -- -- -- IP Priority Queue Address Table -- -- The IP PQ table contains a list of IP adresses used with the -- Priority Queue filtering mechanism. -- ipPQAddressTable OBJECT-TYPE SYNTAX SEQUENCE OF IpPQAddressEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table containing IP addresses, used in an IP Priority Queue Forwarding function." ::= { ctIPPQFilters 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.9.2 ipPQAddressEntry OBJECT-TYPE SYNTAX IpPQAddressEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A description of a single entry." INDEX { ipPQAddressId } ::= { ipPQAddressTable 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.9.2.1 IpPQAddressEntry ::= SEQUENCE { ipPQAddressId INTEGER, ipPQIPAddress IpAddress } ipPQAddressId OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-only STATUS mandatory DESCRIPTION "A unique value identifying an element in a sequence of IP PQ address entries." ::= { ipPQAddressEntry 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.9.2.1.1 ipPQIPAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "Returns an IP address associated with a specific entry in this table." ::= { ipPQAddressEntry 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.9.2.1.2 -- Cabletron Ds3 Extensions Group -- This group is required for any platforms that have a t3 physical -- port. ctDs3ExtensionsTable OBJECT-TYPE SYNTAX SEQUENCE OF CtDs3ExtensionsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table is an extension to the standard ds3 configuration table. It is a list of items that are pertinant to ds3 ports on a platform. There is one entry per ds3 physical port on the platform." ::= { ctDs3Ext 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.10.1 ctDs3ExtensionsEntry OBJECT-TYPE SYNTAX CtDs3ExtensionsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A ds3 extensions entry containing objects relating to the particular ds3 physical port." INDEX { ctDs3ExtensionsEntryIndex } ::= { ctDs3ExtensionsTable 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.10.1.1 CtDs3ExtensionsEntry ::= SEQUENCE { ctDs3ExtensionsEntryIndex INTEGER, ctDs3ExtensionsNumInterfaces INTEGER, ctDs3ExtensionsLineBuildOut INTEGER } ctDs3ExtensionsEntryIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A unique value for each ds3 physical port on the platform." ::= { ctDs3ExtensionsEntry 1 } -- 1.3.6.1.4.1.52.4.1.2.7.2.10.1.1.1 ctDs3ExtensionsNumInterfaces OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of interfaces on this physical port. This number inidicates the number of entries this physical port uses in the ifTable." REFERENCE "rfc-1213" ::= { ctDs3ExtensionsEntry 2 } -- 1.3.6.1.4.1.52.4.1.2.7.2.10.1.1.2 ctDs3ExtensionsLineBuildOut OBJECT-TYPE SYNTAX INTEGER { unknown(1), zeroto255feet(2), a255to450feet(3) } ACCESS read-write STATUS mandatory DESCRIPTION "The line build out setting for this ds3 physical port. Unknown indicates that the setting is neither readable or writable." DEFVAL { zeroto255feet } ::= { ctDs3ExtensionsEntry 3 } -- 1.3.6.1.4.1.52.4.1.2.7.2.10.1.1.3 END