-- Copyright 1999-2007 by Allied Telesis, Inc. -- -- Name : ATIL2.MIB -- Version : 2.5 -- Description : Private MIB for ATI Gigabit Uplink and 10/100M Switches. -- : This MIB will be used in Windows and UNIX Environment. -- History : -- * 04-13-99 - Created. -- * 04-03-02 (Praveen) - Renamed the MIB from fstswtch-mib to atil2-mib -- * 04-17-02 (Praveen) - Added atiL2DeviceNumber. Extended atiL2deviceProductType -- with values for AT-8326GB, AT-9410GB and AT-8350GB -- * 04-18-02 (Praveen) - Added product OID entry for AT-8316F -- * 04-26-02 (Praveen) - Changed atiL2DevicePortSpeed from read-write to read-only -- * 08-23-02 (Praveen) - Added a new product specific group atiL2QOSConfigGroup, -- applicable only to AT-8326GB, AT-9410GB and AT-8350GB. -- Changed range of atiL2DevicePortSTPCost from 0..65535 to -- 1..65535 -- * 11-14-06 (Matthew N) Add the OIDs for 8000/16, 24, 24POE, 48, 48POE, 8POE, 9000/24, 9724Ts, 9748Ts/XP, 10408/XP -- * 01-24-07 (HN) - Changed company name to Allied Telesis Inc. and fixed a few minor issues in addressing MIB -- nodes. -- * 09-03-07 (DNI Tina Lee)- Remove range limitation of atiL2DevicePortSTPCost -- * 01-25-08 (HN) - Added AT-GS950/8PoE AtiL2-MIB DEFINITIONS ::= BEGIN IMPORTS enterprises,Counter,IpAddress,TimeTicks FROM RFC1155-SMI DisplayString FROM RFC1213-MIB TRAP-TYPE FROM RFC-1215 OBJECT-TYPE FROM RFC-1212; -- -- General Definitions -- MacAddress ::= OCTET STRING (SIZE (6)) -- a 6 octet address BridgeId ::= OCTET STRING (SIZE (8)) -- the Bridge -- Identifier as -- used in the -- Spanning Tree -- Protocol to uniquely identify a bridge. Its first two -- octets (in network byte order) contain a priority -- value and its last 6 octets contain the MAC address -- used to refer to a bridge in a unique fashion -- (typically, the numerically smallest MAC address -- of all ports on the bridge). -- Several objects in this MIB module represent values of -- timers used by the Spanning Tree Protocol. In this -- MIB, these timers have values in units of hundreths of -- a second (i.e. 1/100 secs). -- These timers, when stored in a Spanning Tree Protocol's -- BPDU, are in units of 1/256 seconds. Note, however, -- that 802.1D-1990 specifies a settable granularity of -- no more than 1 second for these timers. To avoid -- ambiguity, a data type is defined here as a textual -- convention and all representation of these timers -- in this MIB module are defined using this data type. An -- algorithm is also defined for converting between the -- different units, to ensure a timer's value is not -- distorted by multiple conversions. -- The data type is: Timeout ::= INTEGER -- a STP timer in units of 1/100 seconds -- To convert a Timeout value into a value in units of -- 1/256 seconds, the following algorithm should be used: -- -- b = floor( (n * 256) / 100) -- -- where: -- floor = quotient [ignore remainder] -- n is the value in 1/100 second units -- b is the value in 1/256 second units -- -- To convert the value from 1/256 second units back to -- 1/100 seconds, the following algorithm should be used: -- -- n = ceiling( (b * 100) / 256) -- -- where: -- ceiling = quotient [if remainder is 0], or -- quotient + 1 [if remainder is non-zero] -- n is the value in 1/100 second units -- b is the value in 1/256 second units -- -- Note: it is important that the arithmetic operations are -- done in the order specified (i.e., multiply first, divide -- second). -- OID tree for Allied Telesis Products and MIBs alliedTelesis OBJECT IDENTIFIER ::= { enterprises 207 } atiProduct OBJECT IDENTIFIER ::= { alliedTelesis 1 } swhub OBJECT IDENTIFIER ::= { atiProduct 4 } at-8324 OBJECT IDENTIFIER ::= { swhub 37 } at-8124XL-V2 OBJECT IDENTIFIER ::= { swhub 52 } at-8326GB OBJECT IDENTIFIER ::= { swhub 72 } at-9410GB OBJECT IDENTIFIER ::= { swhub 73 } at-8350GB OBJECT IDENTIFIER ::= { swhub 74 } at-8316F OBJECT IDENTIFIER ::= { swhub 77 } at-8000/16 OBJECT IDENTIFIER ::= { swhub 125 } at-8000/24 OBJECT IDENTIFIER ::= { swhub 126 } at-8000/24POE OBJECT IDENTIFIER ::= { swhub 127 } at-8000/48 OBJECT IDENTIFIER ::= { swhub 128 } at-8000/48POE OBJECT IDENTIFIER ::= { swhub 129 } at-8000/8POE OBJECT IDENTIFIER ::= { swhub 139 } at-9000/24 OBJECT IDENTIFIER ::= { swhub 140 } at-GS950/8PoE OBJECT IDENTIFIER ::= { swhub 147 } swL3 OBJECT IDENTIFIER ::= { atiProduct 14 } at-9724Ts OBJECT IDENTIFIER ::= { swL3 52 } at-9748Ts/XP OBJECT IDENTIFIER ::= { swL3 54 } at-10408/XP OBJECT IDENTIFIER ::= { swL3 66 } mibObject OBJECT IDENTIFIER ::= { alliedTelesis 8 } atiL2Mib OBJECT IDENTIFIER -- LAST-UPDATED "070124000000Z" -- ORGANIZATION "Allied Telesis Inc." -- CONTACT-INFO -- "Allied Telesis Inc. Customer Service -- -- Postal: 19800 North Creek Pkwy #200 -- Bothel, WA 98011 -- USA -- -- Email: support@alliedtelesis.com -- -- DESCRIPTION -- "Private MIB for ATI Gigabit Uplink and 10/100M -- Switches" ::= { mibObject 33} -- Stack Wide Generic Groups atiL2GlobalGroup OBJECT IDENTIFIER ::= {atiL2Mib 1 } atiL2IpGroup OBJECT IDENTIFIER ::= {atiL2Mib 2} atiL2NMGroup OBJECT IDENTIFIER ::= {atiL2Mib 3} atiL2DHCPGroup OBJECT IDENTIFIER ::= {atiL2Mib 4} -- Module Wide Generic Groups atiL2EthernetStatsGroup OBJECT IDENTIFIER ::= {atiL2Mib 6} -- Port on a Module Groups atiL2DevicePortConfigGroup OBJECT IDENTIFIER ::= {atiL2Mib 7} atiL2VlanConfigGroup OBJECT IDENTIFIER ::= {atiL2Mib 8} atiL2IfExt OBJECT IDENTIFIER ::= { atiL2Mib 9} atiL2BridgeMib OBJECT IDENTIFIER ::= { atiL2Mib 10} atiL2BrBase OBJECT IDENTIFIER ::= { atiL2BridgeMib 1 } atiL2BrStp OBJECT IDENTIFIER ::= { atiL2BridgeMib 2 } atiL2BrTp OBJECT IDENTIFIER ::= { atiL2BridgeMib 3 } -- Product specific groups -- Applicable only to at-8326GB, at-9410GB and at-8350GB atiL2QOSConfigGroup OBJECT IDENTIFIER ::= { atiL2Mib 12} -- -- atiL2GlobalGroup -- atiL2SwProduct OBJECT-TYPE SYNTAX DisplayString (SIZE(0..255)) ACCESS read-only STATUS mandatory DESCRIPTION "Identifies the software product the device is running." ::= { atiL2GlobalGroup 1 } atiL2SwVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(0..255)) ACCESS read-only STATUS mandatory DESCRIPTION " Identifies the version number of the present release." ::= { atiL2GlobalGroup 2 } atiL2Reset OBJECT-TYPE SYNTAX INTEGER { switch-no-reset (1), switch-reset (2) } ACCESS read-write STATUS mandatory DESCRIPTION " Object use to reset all the Modules globally." ::= { atiL2GlobalGroup 3 } atiL2MirroringSourceModule OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION " This is the mirror source module number. If the atiL2EthConfigMirrorState is Enabled then the mirror source module/port data gets routed to the mirror destination module/port. Both transmitted and recieved source activity is mirrored to the destination. This arrangement is to put an RMON Probe on the destination port to probe the traffic on the Source port. This object will return a '0' if the MirrorState is not enabled." ::= { atiL2GlobalGroup 4 } atiL2MirroringSourcePort OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION " This is the Source port number for which there is another mirror port.If the atiL2EthConfigMirrorState is Enabled then the mirror portgets routed with all the packets going in and out of Source port. This arrangement is to put an RMON Probe on mirrored port to Probe the traffic on the Source port. One of the port is dedicated to this so that for any port as source port, this dedicated port can be a mirrored port. This object will return a '0' if the MirrorState is not enabled." ::= { atiL2GlobalGroup 5 } atiL2MirroringDestinationModule OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION " This is the mirror destination module number. If the atiL2EthConfigMirrorState is Enabled then the mirror source module/port data gets routed to the mirror destination module/port. Both transmitted and recieved source activity is mirrored to the destination. This arrangement is to put an RMON Probe on the destination port to probe the traffic on the Source port. This object will return a '0' if the MirrorState is not enabled." ::= { atiL2GlobalGroup 6 } atiL2MirroringDestinationPort OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION " This is the Destination port number for which there is another mirror port.If the atiL2EthConfigMirrorState is Enabled then,the mirror portgets routed with all the packets going in and out of Destination port. This arrangement is to put an RMON Probe on mirrored port to Probe the traffic on the Destination port. One of the port is dedicated to this so that for any port as destination port, this dedicated port can be a mirrored port. This object will return a '0' if the MirrorState is not enabled." ::= { atiL2GlobalGroup 7 } atiL2MirrorState OBJECT-TYPE SYNTAX INTEGER { receive-and-transmit(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION " if the state of Mirroring is enabled by selecting one of the two values , then the Mirroring explained above works. If disabled, port operation works normally. No Traffic gets routed from MirroringSourcePort to Destination Mirrored Port." ::= { atiL2GlobalGroup 8 } atiL2IGMPState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute allows an administrative request to configure IGMP" ::= { atiL2GlobalGroup 9 } atiL2DeviceNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The total number of devices in the stack." ::= { atiL2GlobalGroup 10 } -- -- atiL2IpGroup -- -- The Ip Sys group contains IP Address which is current and configured -- IP address which gets effective when reset. Also, subnet mask and -- Default Gateway address. atiL2CurrentIpAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION " The Current IP address is the one which is currently used and is obtained dynamically through one of the protocols interaction.( DHCP or Bootp.) This address is NULL if the Address is Statically configured." ::= { atiL2IpGroup 1 } atiL2ConfiguredIpAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION " The Configured IP address of the device. This is the address configured through Network or Local Omega. " ::= { atiL2IpGroup 2 } atiL2ConfiguredSubnetMask OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION " The Configured Subnet Mask of the device." ::= { atiL2IpGroup 3 } atiL2ConfiguredRouter OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION " The Configured Gateway/Router address of the device" ::= { atiL2IpGroup 4 } atiL2IPAddressStatus OBJECT-TYPE SYNTAX INTEGER { from-dhcp(1), from-bootp(2), from-psuedoip(3), from-Omega(4) } ACCESS read-only STATUS mandatory DESCRIPTION " The IP Address can be obtained/configured by any of the above different ways. This object specifies how IP address currently on the switch Box, was configured/obtained." ::= { atiL2IpGroup 5 } -- -- atiL2NMGroup (SNMP NetManagemnt related MIB object) -- atiL2NwMgrTable OBJECT-TYPE SYNTAX SEQUENCE OF AtiL2NwMgrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of SNMP Trap Manager stations Entries. The number of entries is given by the switchNwMgrTotal mib object." ::= { atiL2NMGroup 1 } atiL2NwMgrEntry OBJECT-TYPE SYNTAX AtiL2NwMgrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Trap receipt Manager Entry containing ipaddress of the configured NMS's to which Traps are sent." INDEX { atiL2NwMgrIndex } ::= { atiL2NwMgrTable 1 } AtiL2NwMgrEntry ::= SEQUENCE { atiL2NwMgrIndex INTEGER, atiL2NwMgrIpAddr IpAddress } atiL2NwMgrIndex OBJECT-TYPE SYNTAX INTEGER (1..4) ACCESS read-only STATUS mandatory DESCRIPTION "The Index of the Managers Ip address." ::= { atiL2NwMgrEntry 1 } atiL2NwMgrIpAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "The IP Address of the NMS host configured." ::= { atiL2NwMgrEntry 2 } -- -- atiL2DHCPGroup -- atiL2DHCPSysGroup OBJECT IDENTIFIER ::= {atiL2DHCPGroup 1 } atiL2DHCPTimerGroup OBJECT IDENTIFIER ::= {atiL2DHCPGroup 2 } --atiL2DHCPCurrentDHCPServerAddress OBJECT-TYPE -- SYNTAX IpAddress -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "The IP address of the DHCP server selected by the end of -- DHCP Protocols 'REQUEST STATE' .DHCP client selects the -- server from the responses ( one or more ) in the -- SELECTSTATE and sends out a DHCPREQUEST to confirm the -- DHCP server selected." -- ::= {atiL2DHCPSysGroup 1} atiL2DHCPCurrentDHCPClientAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "Current IP address of the client. To start with,it might be null. This is filled by the server when sending a DHCPOFFER and the client uses the most comfortable offer from offers sent by different DHCP servers. A DHCPREQUEST packet is sent with the Client address agreed upon to the selected server ( Broadcast). Server Acks back this packet which is where Client/Server moves to the Bound state. Once reached into Bound state, the client address is made the official address on the client." ::= {atiL2DHCPSysGroup 1} atiL2DHCPSubnetMask OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "When the client/server reaches the BOUND state, this is one of the parameters set by the server." ::= {atiL2DHCPSysGroup 2} atiL2DHCPCurrentRelayAgentAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The IP address of the DHCP relay Agent on the same subnet. Normally there will be no DHCP server on each of the subnet and this Relay Agent will act in sending server across the subnets. There might not be any relay agent. This depends on the network Toplogy like where is the DHCP server and DHCP client." ::= {atiL2DHCPSysGroup 3} atiL2DHCPNextDHCPServerAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The IP address of the next DHCP server to be used during bootstrap. This address is sent by the DHCP server in the messages DHCPOFFER, DHCPACK,DHCPNACK." ::= {atiL2DHCPSysGroup 4} atiL2DHCPLeaseTimer OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "When the client/server reaches the BOUND state, this is one of the parameters set by the server. The lease time period in seconds for the DHCP client for using IP address on lease from the server. At the end of 50% of this timer a renewal request is sent by the client . This is the next Object atiL2DHCPReacquisitionTimer." ::= {atiL2DHCPTimerGroup 1} atiL2DHCPReacquisitionTimer OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "When the client/server reaches the BOUND state, this is one of the parameters set by the server. Mentioned in RFC2131 4.4.5 as T1, this renewal time period in secs for the DHCP client is for using IP address on lease from the server Once the Reacquisition Timer period in secs after the lease period is reached, the client sends a DHCPREQUEST to the DHCP server requesting for renewal of the lease. Default would be 50% of the Lease timer which is represeneted by the above object. The client moves from BOUND to RENEW state once the DHCPREQUEST is sent after time T1 secs is passed from the start of to release time. T1 is always less than T2 ( see below for 'T2') which is less than the lease Timer period." ::= {atiL2DHCPTimerGroup 2} atiL2DHCPExpirationTimer OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "When the client/server reaches the BOUND state, this is one of the parameters set by the server. Mentioned in RFC2131 4.4.5 as T2,this Expiration time period in secs is the time period in secs during which DHCP has gone through the BOUND->RENEWAL state. After T1 secs and when the state machine reaches T2 secs, ( T1 < T2 < lease period), DHCP client sends another DHCPREQUEST to the server asking the server to renew the lease for the IP parameters. By default it would be 87.5% of the Lease timer .If there is DHCPACK then the DHCP client moves from REBIND to BOUND. Else it moves to INIT state where it starts all over again sending a request for DHCPDISCOVER." ::= {atiL2DHCPTimerGroup 3 } -- -- atiL2EthernetStatsGroup (Ethernet Monitor Group) -- -- The Monitor group contains statistics measured -- per module identified by the module Id. -- These statistics take the form of free running counters that start -- from zero. atiL2EthMonStatsGroup OBJECT IDENTIFIER ::= { atiL2EthernetStatsGroup 1} atiL2EthErrStatsGroup OBJECT IDENTIFIER ::= { atiL2EthernetStatsGroup 2} atiL2EthMonStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF AtiL2EthMonStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of statistics entries." ::= { atiL2EthMonStatsGroup 1 } atiL2EthMonStatsEntry OBJECT-TYPE SYNTAX AtiL2EthMonStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A collection of statistics kept for a particular port." INDEX {atiL2EthMonModuleId } ::= { atiL2EthMonStatsTable 1 } AtiL2EthMonStatsEntry ::= SEQUENCE { atiL2EthMonModuleId INTEGER, atiL2EthMonRxGoodFrames Counter, atiL2EthMonTxGoodFrames Counter, atiL2EthMonTxTotalBytes Counter , atiL2EthMonTxDeferred Counter , atiL2EthMonTxCollisions Counter, atiL2EthMonTxBroadcastFrames Counter, atiL2EthMonTxMulticastFrames Counter, atiL2EthMonRxOverruns Counter } atiL2EthMonModuleId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This Object Identifies the Module Id for which the Statistics is collected." ::= { atiL2EthMonStatsEntry 1 } atiL2EthMonRxGoodFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of Good Frames received on this module." ::= { atiL2EthMonStatsEntry 2 } atiL2EthMonTxGoodFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of Good Frames Transmitted by this module." ::= { atiL2EthMonStatsEntry 3 } atiL2EthMonTxTotalBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of Bytes transmitted from this module." ::= { atiL2EthMonStatsEntry 4 } atiL2EthMonTxDeferred OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS deprecated DESCRIPTION "This is the count of first time Transmission attempt which failed on an interface due to medium being busy." ::= { atiL2EthMonStatsEntry 5 } atiL2EthMonTxCollisions OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of collisions while switching on an interface." ::= { atiL2EthMonStatsEntry 6 } atiL2EthMonTxBroadcastFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of Transmit Broadcast Frames while switching on an interface." ::= { atiL2EthMonStatsEntry 7 } atiL2EthMonTxMulticastFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of Transmit Multicast while switching on an interface." ::= { atiL2EthMonStatsEntry 8 } atiL2EthMonRxOverruns OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of Recieved Overrun Frames while switching on an interface." ::= { atiL2EthMonStatsEntry 9 } -- -- The Following is a Per Port MonStats Table. -- atiL2EthPortMonStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF AtiL2EthPortMonStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of statistics entries per Port on a Module." ::= { atiL2EthMonStatsGroup 2 } atiL2EthPortMonStatsEntry OBJECT-TYPE SYNTAX AtiL2EthPortMonStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A collection of statistics kept for a particular port." INDEX {atiL2EthPortMonModuleId,atiL2EthPortMonPortId} ::= { atiL2EthPortMonStatsTable 1 } AtiL2EthPortMonStatsEntry ::= SEQUENCE { atiL2EthPortMonModuleId INTEGER, atiL2EthPortMonPortId INTEGER, atiL2EthPortMonRxGoodFrames Counter, atiL2EthPortMonTxGoodFrames Counter, atiL2EthPortMonTxTotalBytes Counter , atiL2EthPortMonTxDeferred Counter , atiL2EthPortMonTxCollisions Counter, atiL2EthPortMonTxBroadcastFrames Counter, atiL2EthPortMonTxMulticastFrames Counter, atiL2EthPortMonRxOverruns Counter } atiL2EthPortMonModuleId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This Object Identifies the Module Id for which the Statistics is collected." ::= { atiL2EthPortMonStatsEntry 1 } atiL2EthPortMonPortId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This Object Identifies the Port on the Module recognised by EthMonPortModuleId for which the Statistics is collected." ::= { atiL2EthPortMonStatsEntry 2 } atiL2EthPortMonRxGoodFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of Good Frames received on this module." ::= { atiL2EthPortMonStatsEntry 3 } atiL2EthPortMonTxGoodFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of Good Frames Transmitted by this module." ::= { atiL2EthPortMonStatsEntry 4 } atiL2EthPortMonTxTotalBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of Bytes transmitted from this module." ::= { atiL2EthPortMonStatsEntry 5 } atiL2EthPortMonTxDeferred OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS deprecated DESCRIPTION "This is the count of first time Transmission attempt which failed on an interface due to medium being busy." ::= { atiL2EthPortMonStatsEntry 6 } atiL2EthPortMonTxCollisions OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of collisions while switching on an interface." ::= { atiL2EthPortMonStatsEntry 7 } atiL2EthPortMonTxBroadcastFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of Transmit Broadcast Frames on this port and Module while switching on an interface." ::= { atiL2EthPortMonStatsEntry 8 } atiL2EthPortMonTxMulticastFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of Transmit Multicast on this port and Module while switching on an interface." ::= { atiL2EthPortMonStatsEntry 9 } atiL2EthPortMonRxOverruns OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of Recieved Overrun Frames on this port and Module while switching on an interface." ::= { atiL2EthPortMonStatsEntry 10 } -- -- The Ethernet Error Statistics -- -- The Ethernet Error Statistics group contains certain errors -- measured by the switch. These statistics take the form of -- free running counters that start from zero. -- atiL2EthErrStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF AtiL2EthErrStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of statistics entries." ::= { atiL2EthErrStatsGroup 1 } atiL2EthErrorStatsEntry OBJECT-TYPE SYNTAX AtiL2EthErrStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A collection of statistics kept for a particular port." INDEX {atiL2EthErrModuleId } ::= { atiL2EthErrStatsTable 1 } AtiL2EthErrStatsEntry ::= SEQUENCE { atiL2EthErrModuleId INTEGER, atiL2EthErrorCRC Counter, atiL2EthErrorAlignment Counter, atiL2EthErrorRxBadFrames Counter , atiL2EthErrorLateCollisions Counter, atiL2EthErrorTxTotal Counter } atiL2EthErrModuleId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This Object Identifies the Module Id for which the Statistics is collected." ::= { atiL2EthErrorStatsEntry 1 } atiL2EthErrorCRC OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of CRC errors on received packets." ::= { atiL2EthErrorStatsEntry 2 } atiL2EthErrorAlignment OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of packets received that has alignment errors." ::= { atiL2EthErrorStatsEntry 3 } atiL2EthErrorRxBadFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The counter is incremented when a bad frame was received." ::= { atiL2EthErrorStatsEntry 4 } atiL2EthErrorLateCollisions OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This object counts the number of times the collison was detected in the port." ::= { atiL2EthErrorStatsEntry 5 } atiL2EthErrorTxTotal OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of error resulted from transfer operations." ::= { atiL2EthErrorStatsEntry 6 } -- -- EthErrStats per Port. -- atiL2EthPortErrStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF AtiL2EthPortErrStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of statistics entries." ::= { atiL2EthErrStatsGroup 2 } atiL2EthPortErrorStatsEntry OBJECT-TYPE SYNTAX AtiL2EthPortErrStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A collection of statistics kept for a particular port." INDEX {atiL2EthPortErrModuleId, atiL2EthPortErrPortId} ::= { atiL2EthPortErrStatsTable 1 } AtiL2EthPortErrStatsEntry ::= SEQUENCE { atiL2EthPortErrModuleId INTEGER, atiL2EthPortErrPortId INTEGER, atiL2EthPortErrorCRC Counter, atiL2EthPortErrorAlignment Counter, atiL2EthPortErrorRxBadFrames Counter , atiL2EthPortErrorLateCollisions Counter, atiL2EthPortErrorTxTotal Counter } atiL2EthPortErrModuleId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This Object Identifies the Module Id for which the Statistics is collected." ::= { atiL2EthPortErrorStatsEntry 1 } atiL2EthPortErrPortId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This Object Identifies the Port on the Module recognised by the above Object for which the Statistics is collected." ::= { atiL2EthPortErrorStatsEntry 2 } atiL2EthPortErrorCRC OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of CRC errors on received packets." ::= { atiL2EthPortErrorStatsEntry 3 } atiL2EthPortErrorAlignment OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of packets received that has alignment errors." ::= { atiL2EthPortErrorStatsEntry 4 } atiL2EthPortErrorRxBadFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The counter is incremented when a bad frame was received." ::= { atiL2EthPortErrorStatsEntry 5 } atiL2EthPortErrorLateCollisions OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This object counts the number of times the collison was detected in the port." ::= { atiL2EthPortErrorStatsEntry 6 } atiL2EthPortErrorTxTotal OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of error resulted from transfer operations." ::= { atiL2EthPortErrorStatsEntry 7 } -- -- atiL2DevicePortConfigGroup -- atiL2DevicePortTable OBJECT-TYPE SYNTAX SEQUENCE OF AtiL2DevicePortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table of basic port configuration information." ::= { atiL2DevicePortConfigGroup 1 } atiL2DevicePortEntry OBJECT-TYPE SYNTAX AtiL2DevicePortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the port config table." INDEX { atiL2DeviceId,atiL2DevicePortNumber } ::= { atiL2DevicePortTable 1 } AtiL2DevicePortEntry ::= SEQUENCE { atiL2DeviceId INTEGER, atiL2DevicePortNumber INTEGER, atiL2DevicePortAutosenseOrHalfDuplex INTEGER, atiL2DevicePortLinkState INTEGER, atiL2DevicePortDuplexStatus INTEGER , atiL2DevicePortSpeed INTEGER, atiL2DevicePortState INTEGER, atiL2DevicePortSTPConfig INTEGER, atiL2DevicePortBridgeid INTEGER, atiL2DevicePortSTPCost INTEGER, atiL2DevicePortSTPPriority INTEGER, atiL2DevicePortFlowControlEnable INTEGER, atiL2DevicePortQOSPriorityConfig INTEGER } atiL2DeviceId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object identifies the Module Id of the switch Stack." ::= { atiL2DevicePortEntry 1 } atiL2DevicePortNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object identifies the Port on atiL2ModuleId of the switch Stack." ::= { atiL2DevicePortEntry 2 } atiL2DevicePortAutosenseOrHalfDuplex OBJECT-TYPE SYNTAX INTEGER { portAutoSense(1), forceHalfDuplex-10M(2), forceHalfDuplex-100M(3), forceFullDuplex-10M(4), forceFullDuplex-100M(5), forceHalfDuplex-1G(6), forceFullDuplex-1G(7) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute allows an administrative request to configure whether this port can Autosense or Force the Half Duplex or Full Duplex on different Port Speeds." ::= { atiL2DevicePortEntry 4 } atiL2DevicePortLinkState OBJECT-TYPE SYNTAX INTEGER { online(1), offline(2) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute allows an administrative request to read the status of link state on this port." ::= { atiL2DevicePortEntry 5 } atiL2DevicePortDuplexStatus OBJECT-TYPE SYNTAX INTEGER { fullDuplex(1), halfDuplex(2), autosense(3) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute allows an administrative request to read the status of Duplex on this port." ::= { atiL2DevicePortEntry 6 } atiL2DevicePortSpeed OBJECT-TYPE SYNTAX INTEGER { tenMBits(1), hundredMBits(2), gigaBits(3), unknown(4) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute allows an administrative request to read or write the speed of this port. This Object is valid only for 10/100Mbits and gigaBits ports. The only gigabit port that can be set is that of AT-A14 and it's values can be either 2 or 3." ::= { atiL2DevicePortEntry 7 } atiL2DevicePortState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2), blocking(3), listening(4), learning(5) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute allows an administrative request to disable or enable communications on this port.It also responds with the status of the port .Except enabled(1) and disabled(2), all values are read-only status." ::= { atiL2DevicePortEntry 8 } atiL2DevicePortSTPConfig OBJECT-TYPE SYNTAX INTEGER { enable (1), disable (2) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute allows a bridging Mode to be configured with either Spanning Tree enabled or disabled. When Spanning tree is enabled, make sure that this port is belonging to a valid Bridge_id. Spanning Tree is enabled only when a valid Bridge_id is set." ::= { atiL2DevicePortEntry 10} atiL2DevicePortBridgeid OBJECT-TYPE SYNTAX INTEGER (1..64) ACCESS read-write STATUS mandatory DESCRIPTION " The Bridge to which this port belongs to." ::= { atiL2DevicePortEntry 11 } atiL2DevicePortSTPCost OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The Cost of the Spanning Tree Protocol.This object is valid only when STP is enabled." ::= { atiL2DevicePortEntry 12 } atiL2DevicePortSTPPriority OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-write STATUS mandatory DESCRIPTION " The Priority of the spanning Tree Protocol. This object is valid when STP is enabled." ::= { atiL2DevicePortEntry 13 } atiL2DevicePortFlowControlEnable OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } ACCESS read-write STATUS deprecated DESCRIPTION "This per-port attribute describes whether the port identified has flow Control Enabled or not. Flow Control on Full Duplex and Half Duplex is detected and automatically, flow control accordingly is taken care of. By Default, Flow Control is Disabled." ::= { atiL2DevicePortEntry 14 } atiL2DevicePortQOSPriorityConfig OBJECT-TYPE SYNTAX INTEGER { lowest(0), low(1), high(2), highest(3) } ACCESS read-write STATUS deprecated DESCRIPTION "This per-port attribute is applicable only to at-8324, at-8124XL-V2 and at-8316 and it allows for the configuration of the Priority of the port to be high or Low. In a switch environment, Ports with high Priority and traffic from and to the ports get more priority when compared with those with normal priority. By Default, all ports have Normal Priority." ::= { atiL2DevicePortEntry 17 } -- -- atiL2VlanConfigGroup -- atiL2BasicVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF AtiL2BasicVlanEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table of Virtual LAN configured." ::= { atiL2VlanConfigGroup 1 } atiL2BasicVlanEntry OBJECT-TYPE SYNTAX AtiL2BasicVlanEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the table, containing VLAN information." INDEX { atiL2BeVlanIndex } ::= { atiL2BasicVlanTable 1 } AtiL2BasicVlanEntry ::= SEQUENCE { atiL2BeVlanIndex INTEGER, atiL2BeVlanName DisplayString, atiL2BeVlanTagId INTEGER, atiL2BeVlanModule1UntaggedPorts DisplayString, atiL2BeVlanModule1TaggedPorts DisplayString, atiL2BeVlanRowStatus INTEGER } atiL2BeVlanIndex OBJECT-TYPE SYNTAX INTEGER (1..64) ACCESS read-only STATUS mandatory DESCRIPTION "This object identifies the VLAN." ::= { atiL2BasicVlanEntry 1 } atiL2BeVlanName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..20)) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute associates a user defined string with the Virtual LAN. To configure a new VLAN, do 'set' operation on this object with the VLAN name. To delete a VLAN, do 'set' operation with string '*', where is the module number (1..8) from which the delete request is being sent. If a vlan is being created or modified, before configuring any of the objects in this row, set atiL2VlanStatus to 'under-construction' and once configured with all the information, set the same object to operational. This step is not required when deleting a vlan." ::= { atiL2BasicVlanEntry 2 } atiL2BeVlanTagId OBJECT-TYPE SYNTAX INTEGER (1..4095) ACCESS read-write STATUS mandatory DESCRIPTION "This object configures the VId in the Tag Information header in accordance with 802.1q spec. Before configuring any of the objects in this row , set the atiL2VlanStatus to 'under-construction' and once configured with all the information, please set the same object to operational." ::= { atiL2BasicVlanEntry 3 } atiL2BeVlanModule1UntaggedPorts OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS mandatory DESCRIPTION "This Object builds the Output Ports on the Module that participate in the Vlan with the atiL2BeVlanName. The Format of the input string would be like '1,2,5,7,12..15,18-22,26'. Before configuring any of the objects in this row , set the atiL2VlanStatus to 'under-construction' and once configured with all the information, please set the same object to operational." ::= { atiL2BasicVlanEntry 4 } atiL2BeVlanModule1TaggedPorts OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS mandatory DESCRIPTION "This Object builds the Output Ports on the Module atiL2BeVlanModuleId that participate in the Vlan with the atiL2BeVlanName. The Format of the input string would be like '1,2,5,7,12'. Please select the Module by setting the atiL2BeVlanModuleId with the Module Id and then set the port mask. If this is not set, by default this will be set to 1. Before configuring any of the objects in this row , set the atiL2VlanStatus to 'under-construction' and once configured with all the information, please set the same object to operational." ::= { atiL2BasicVlanEntry 5 } atiL2BeVlanRowStatus OBJECT-TYPE SYNTAX INTEGER { idle(1), operational(2), under-construction(3), not-operational(4) } ACCESS read-write STATUS mandatory DESCRIPTION "This object is used to create or modify a vlan. The user should first set this object to under-construction. After the vlan name, the tag Id and the ports belonging to the vlan are configured/modified, this object should be set to operational. If it is not set to operational, the whole row will be lost and the vlan will not be configured in the switch." ::= { atiL2BasicVlanEntry 20 } -- -- Port2VlanTable. -- atiL2Port2VlanTable OBJECT-TYPE SYNTAX SEQUENCE OF AtiL2Port2VlanEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table of per port Virtual LAN configuration." ::= { atiL2VlanConfigGroup 2 } atiL2Port2VlanEntry OBJECT-TYPE SYNTAX AtiL2Port2VlanEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the table, containing per port VLAN information." INDEX {atiL2PvModuleId, atiL2PvPortNumber } ::= { atiL2Port2VlanTable 1 } AtiL2Port2VlanEntry ::= SEQUENCE { atiL2PvModuleId INTEGER, atiL2PvPortNumber INTEGER, atiL2PvVlanName DisplayString } atiL2PvModuleId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object identifies the Module Id on the switching Stack." ::= { atiL2Port2VlanEntry 1 } atiL2PvPortNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object identifies the port on the Module atiL2PvModuleId ." ::= { atiL2Port2VlanEntry 2 } atiL2PvVlanName OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS mandatory DESCRIPTION "This attribute associates a user defined string with the Virtual LAN. This Object is the same as atiL2BeVlanName. Please make sure to give the same string as atiL2BeVlanName." ::= { atiL2Port2VlanEntry 3 } -- -- atiL2IfExt Group -- atiL2IfExtensions OBJECT IDENTIFIER ::= { atiL2IfExt 1 } atiIfExtnTable OBJECT-TYPE SYNTAX SEQUENCE OF AtiIfExtnEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of interface entries. The number of entries is given by the value of ifNumber." ::= { atiL2IfExtensions 1 } atiIfExtnEntry OBJECT-TYPE SYNTAX AtiIfExtnEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An interface entry containing objects at the subnetwork layer and below for a particular interface." INDEX { atiIfExtnIndex } ::= { atiIfExtnTable 1 } AtiIfExtnEntry ::= SEQUENCE { atiIfExtnIndex INTEGER, atiIfExtnModuleId INTEGER, atiIfExtnPort INTEGER } atiIfExtnIndex OBJECT-TYPE SYNTAX INTEGER(1..256) ACCESS read-only STATUS mandatory DESCRIPTION "A unique value for each interface corresponding to the ifIndex value for the same interface." ::= { atiIfExtnEntry 1 } atiIfExtnModuleId OBJECT-TYPE SYNTAX INTEGER(1..8) ACCESS read-only STATUS mandatory DESCRIPTION "The unit number associated with this particular interface." ::= { atiIfExtnEntry 2 } atiIfExtnPort OBJECT-TYPE SYNTAX INTEGER(1..32) ACCESS read-only STATUS mandatory DESCRIPTION "The port number within a unit or slot." ::= { atiIfExtnEntry 3 } -- -- atiL2BridgeMib -- -- the atiL2BrBase Table atiL2BrBaseTable OBJECT-TYPE SYNTAX SEQUENCE OF AtiL2BrBaseEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table of basic bridge information." ::= { atiL2BrBase 1 } atiL2BrBaseEntry OBJECT-TYPE SYNTAX AtiL2BrBaseEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atiL2BrBaseTable." INDEX { atiL2BrBaseLanId } ::= { atiL2BrBaseTable 1 } AtiL2BrBaseEntry ::= SEQUENCE { atiL2BrBaseLanId INTEGER, atiL2BrBaseBridgeAddress MacAddress, atiL2BrBaseNumPorts INTEGER, atiL2BrBaseType INTEGER } atiL2BrBaseLanId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object uniquely identifies the lan or Virtual lan." ::= { atiL2BrBaseEntry 1 } atiL2BrBaseBridgeAddress OBJECT-TYPE SYNTAX MacAddress ACCESS read-only STATUS mandatory DESCRIPTION "The MAC address used by this bridge when it must be referred to in a unique fashion. It is recommended that this be the numerically smallest MAC address of all ports that belong to this bridge. However it is only required to be unique. When concatenated with atiL2BrStpPriority a unique BridgeIdentifier is formed which is used in the Spanning Tree Protocol." REFERENCE "IEEE 802.1D-1990: Sections 6.4.1.1.3 and 3.12.5" ::= { atiL2BrBaseEntry 2 } atiL2BrBaseNumPorts OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of ports controlled by this bridging entity." REFERENCE "IEEE 802.1D-1990: Section 6.4.1.1.3" ::= { atiL2BrBaseEntry 3 } atiL2BrBaseType OBJECT-TYPE SYNTAX INTEGER { unknown(1), transparent-only(2), sourceroute-only(3), srt(4) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates what type of bridging this bridge can perform. If a bridge is actually performing a certain type of bridging this will be indicated by entries in the port table for the given type." ::= { atiL2BrBaseEntry 4 } -- The Generic Bridge Port Table atiL2BrBasePortTable OBJECT-TYPE SYNTAX SEQUENCE OF AtiL2BrBasePortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table that contains generic information about every port that is associated with this bridge. Transparent, source-route, and srt ports are included." ::= { atiL2BrBase 4 } atiL2BrBasePortEntry OBJECT-TYPE SYNTAX AtiL2BrBasePortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of information for each port of the bridge." REFERENCE "IEEE 802.1D-1990: Section 6.4.2, 6.6.1" INDEX { atiL2BrBasePortLanId, atiL2BrBasePort } ::= { atiL2BrBasePortTable 1 } AtiL2BrBasePortEntry ::= SEQUENCE { atiL2BrBasePortLanId INTEGER, atiL2BrBasePort INTEGER, atiL2BrBasePortIfIndex INTEGER, atiL2BrBasePortCircuit OBJECT IDENTIFIER, atiL2BrBasePortDelayExceededDiscards Counter, atiL2BrBasePortMtuExceededDiscards Counter } atiL2BrBasePortLanId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object uniquely identifies the lan or Virtual lan." ::= { atiL2BrBasePortEntry 1 } atiL2BrBasePort OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-only STATUS mandatory DESCRIPTION "The port number of the port for which this entry contains bridge management information." ::= { atiL2BrBasePortEntry 2 } atiL2BrBasePortIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The value of the instance of the ifIndex object, defined in MIB-II, for the interface corresponding to this port." ::= { atiL2BrBasePortEntry 3 } atiL2BrBasePortCircuit OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS mandatory DESCRIPTION "For a port which (potentially) has the same value of atiL2BrBasePortIfIndex as another port on the same bridge, this object contains the name of an object instance unique to this port. For example, in the case where multiple ports correspond one- to-one with multiple X.25 virtual circuits, this value might identify an (e.g., the first) object instance associated with the X.25 virtual circuit corresponding to this port. For a port which has a unique value of atiL2BrBasePortIfIndex, this object can have the value { 0 0 }." ::= { atiL2BrBasePortEntry 4 } atiL2BrBasePortDelayExceededDiscards OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames discarded by this port due to excessive transit delay through the bridge. It is incremented by both transparent and source route bridges." REFERENCE "IEEE 802.1D-1990: Section 6.6.1.1.3" ::= { atiL2BrBasePortEntry 5 } atiL2BrBasePortMtuExceededDiscards OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames discarded by this port due to an excessive size. It is incremented by both transparent and source route bridges." REFERENCE "IEEE 802.1D-1990: Section 6.6.1.1.3" ::= { atiL2BrBasePortEntry 6 } -- -- the atiL2BrStp group -- -- Implementation of the atiL2BrStp group is optional. It is -- implemented by those bridges that support the Spanning Tree -- Protocol. atiL2BrStpTable OBJECT-TYPE SYNTAX SEQUENCE OF AtiL2BrStpEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table of bridge spanning tree information." ::= { atiL2BrStp 1 } atiL2BrStpEntry OBJECT-TYPE SYNTAX AtiL2BrStpEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the atiL2BrStpTable." INDEX { atiL2BrStpLanId } ::= { atiL2BrStpTable 1 } AtiL2BrStpEntry ::= SEQUENCE { atiL2BrStpLanId INTEGER, atiL2BrStpProtocolSpecification INTEGER, atiL2BrStpPriority INTEGER, atiL2BrStpTimeSinceTopologyChange TimeTicks, atiL2BrStpTopChanges Counter, atiL2BrStpDesignatedRoot BridgeId, atiL2BrStpRootCost INTEGER, atiL2BrStpRootPort INTEGER, atiL2BrStpMaxAge Timeout, atiL2BrStpHelloTime Timeout, atiL2BrStpHoldTime INTEGER, atiL2BrStpForwardDelay Timeout, atiL2BrStpBridgeMaxAge Timeout, atiL2BrStpBridgeHelloTime Timeout, atiL2BrStpBridgeForwardDelay Timeout } atiL2BrStpLanId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object uniquely identifies the lan or Virtual lan." ::= { atiL2BrStpEntry 1 } atiL2BrStpProtocolSpecification OBJECT-TYPE SYNTAX INTEGER { unknown(1), decLb100(2), ieee8021d(3) } ACCESS read-only STATUS mandatory DESCRIPTION "An indication of what version of the Spanning Tree Protocol is being run. The value 'decLb100(2)' indicates the DEC LANbridge 100 Spanning Tree protocol. IEEE 802.1d implementations will return 'ieee8021d(3)'. If future versions of the IEEE Spanning Tree Protocol are released that are incompatible with the current version a new value will be defined." ::= { atiL2BrStpEntry 2 } atiL2BrStpPriority OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-write STATUS mandatory DESCRIPTION "The value of the write-able portion of the Bridge ID, i.e., the first two octets of the (8 octet long) Bridge ID. The other (last) 6 octets of the Bridge ID are given by the value of atiL2BrBaseBridgeAddress." REFERENCE "IEEE 802.1D-1990: Section 4.5.3.7" ::= { atiL2BrStpEntry 3 } atiL2BrStpTimeSinceTopologyChange OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity." REFERENCE "IEEE 802.1D-1990: Section 6.8.1.1.3" ::= { atiL2BrStpEntry 4 } atiL2BrStpTopChanges OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of topology changes detected by this bridge since the management entity was last reset or initialized." REFERENCE "IEEE 802.1D-1990: Section 6.8.1.1.3" ::= { atiL2BrStpEntry 5 } atiL2BrStpDesignatedRoot OBJECT-TYPE SYNTAX BridgeId ACCESS read-only STATUS mandatory DESCRIPTION "The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node." REFERENCE "IEEE 802.1D-1990: Section 4.5.3.1" ::= { atiL2BrStpEntry 6 } atiL2BrStpRootCost OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The cost of the path to the root as seen from this bridge." REFERENCE "IEEE 802.1D-1990: Section 4.5.3.2" ::= { atiL2BrStpEntry 7 } atiL2BrStpRootPort OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The port number of the port which offers the lowest cost path from this bridge to the root bridge." REFERENCE "IEEE 802.1D-1990: Section 4.5.3.3" ::= { atiL2BrStpEntry 8 } atiL2BrStpMaxAge OBJECT-TYPE SYNTAX Timeout ACCESS read-only STATUS mandatory DESCRIPTION "The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using." REFERENCE "IEEE 802.1D-1990: Section 4.5.3.4" ::= { atiL2BrStpEntry 9 } atiL2BrStpHelloTime OBJECT-TYPE SYNTAX Timeout ACCESS read-only STATUS mandatory DESCRIPTION "The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using." REFERENCE "IEEE 802.1D-1990: Section 4.5.3.5" ::= { atiL2BrStpEntry 10 } atiL2BrStpHoldTime OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second." REFERENCE "IEEE 802.1D-1990: Section 4.5.3.14" ::= { atiL2BrStpEntry 11 } atiL2BrStpForwardDelay OBJECT-TYPE SYNTAX Timeout ACCESS read-only STATUS mandatory DESCRIPTION "This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to atiL2BrStpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.]" REFERENCE "IEEE 802.1D-1990: Section 4.5.3.6" ::= { atiL2BrStpEntry 12 } atiL2BrStpBridgeMaxAge OBJECT-TYPE SYNTAX Timeout (600..4000) ACCESS read-write STATUS mandatory DESCRIPTION "The value that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of atiL2BrStpBridgeHelloTime. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds." REFERENCE "IEEE 802.1D-1990: Section 4.5.3.8" ::= { atiL2BrStpEntry 13 } atiL2BrStpBridgeHelloTime OBJECT-TYPE SYNTAX Timeout (100..1000) ACCESS read-write STATUS mandatory DESCRIPTION "The value that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D- 1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds." REFERENCE "IEEE 802.1D-1990: Section 4.5.3.9" ::= { atiL2BrStpEntry 14 } atiL2BrStpBridgeForwardDelay OBJECT-TYPE SYNTAX Timeout (400..3000) ACCESS read-write STATUS mandatory DESCRIPTION "The value that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of atiL2BrStpBridgeMaxAge. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds." REFERENCE "IEEE 802.1D-1990: Section 4.5.3.10" ::= { atiL2BrStpEntry 15 } -- -- The Spanning Tree Port Table -- atiL2BrStpPortTable OBJECT-TYPE SYNTAX SEQUENCE OF AtiL2BrStpPortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table that contains port-specific information for the Spanning Tree Protocol." ::= { atiL2BrStp 15 } atiL2BrStpPortEntry OBJECT-TYPE SYNTAX AtiL2BrStpPortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of information maintained by every port about the Spanning Tree Protocol state for that port." INDEX { atiL2BrStpPortLanId, atiL2BrStpPort } ::= { atiL2BrStpPortTable 1 } AtiL2BrStpPortEntry ::= SEQUENCE { atiL2BrStpPortLanId INTEGER, atiL2BrStpPort INTEGER, atiL2BrStpPortPriority INTEGER, atiL2BrStpPortState INTEGER, atiL2BrStpPortEnable INTEGER, atiL2BrStpPortPathCost INTEGER, atiL2BrStpPortDesignatedRoot BridgeId, atiL2BrStpPortDesignatedCost INTEGER, atiL2BrStpPortDesignatedBridge BridgeId, atiL2BrStpPortDesignatedPort OCTET STRING, atiL2BrStpPortForwardTransitions Counter } atiL2BrStpPortLanId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object uniquely identifies the lan or Virtual lan." ::= { atiL2BrStpPortEntry 1 } atiL2BrStpPort OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-only STATUS mandatory DESCRIPTION "The port number of the port for which this entry contains Spanning Tree Protocol management information." REFERENCE "IEEE 802.1D-1990: Section 6.8.2.1.2" ::= { atiL2BrStpPortEntry 2 } atiL2BrStpPortPriority OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of atiL2BrStpPort." REFERENCE "IEEE 802.1D-1990: Section 4.5.5.1" ::= { atiL2BrStpPortEntry 3 } atiL2BrStpPortState OBJECT-TYPE SYNTAX INTEGER { disabled(1), blocking(2), listening(3), learning(4), forwarding(5), broken(6) } ACCESS read-only STATUS mandatory DESCRIPTION "The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see atiL2BrStpPortEnable), this object will have a value of disabled(1)." REFERENCE "IEEE 802.1D-1990: Section 4.5.5.2" ::= { atiL2BrStpPortEntry 4 } atiL2BrStpPortEnable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The enabled/disabled status of the port." REFERENCE "IEEE 802.1D-1990: Section 4.5.5.2" ::= { atiL2BrStpPortEntry 5 } atiL2BrStpPortPathCost OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-write STATUS mandatory DESCRIPTION "The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN." REFERENCE "IEEE 802.1D-1990: Section 4.5.5.3" ::= { atiL2BrStpPortEntry 6 } atiL2BrStpPortDesignatedRoot OBJECT-TYPE SYNTAX BridgeId ACCESS read-only STATUS mandatory DESCRIPTION "The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached." REFERENCE "IEEE 802.1D-1990: Section 4.5.5.4" ::= { atiL2BrStpPortEntry 7 } atiL2BrStpPortDesignatedCost OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs." REFERENCE "IEEE 802.1D-1990: Section 4.5.5.5" ::= { atiL2BrStpPortEntry 8 } atiL2BrStpPortDesignatedBridge OBJECT-TYPE SYNTAX BridgeId ACCESS read-only STATUS mandatory DESCRIPTION "The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment." REFERENCE "IEEE 802.1D-1990: Section 4.5.5.6" ::= { atiL2BrStpPortEntry 9 } atiL2BrStpPortDesignatedPort OBJECT-TYPE SYNTAX OCTET STRING (SIZE (2)) ACCESS read-only STATUS mandatory DESCRIPTION "The Port Identifier of the port on the Designated Bridge for this port's segment." REFERENCE "IEEE 802.1D-1990: Section 4.5.5.7" ::= { atiL2BrStpPortEntry 10 } atiL2BrStpPortForwardTransitions OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of times this port has transitioned from the Learning state to the Forwarding state." ::= { atiL2BrStpPortEntry 11 } -- -- the atiL2BrTp group -- -- Implementation of the atiL2BrTp group is optional. It is -- implemented by those bridges that support the transparent -- bridging mode. A transparent or SRT bridge will implement -- this group. -- -- Port Table for Transparent Bridges -- atiL2BrTpPortTable OBJECT-TYPE SYNTAX SEQUENCE OF AtiL2BrTpPortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table that contains information about every port that is associated with this transparent bridge." ::= { atiL2BrTp 4 } atiL2BrTpPortEntry OBJECT-TYPE SYNTAX AtiL2BrTpPortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of information for each port of a transparent bridge." INDEX { atiL2BrTpPortLanId, atiL2BrTpPort } ::= { atiL2BrTpPortTable 1 } AtiL2BrTpPortEntry ::= SEQUENCE { atiL2BrTpPortLanId INTEGER, atiL2BrTpPort INTEGER, atiL2BrTpPortMaxInfo INTEGER, atiL2BrTpPortInFrames Counter, atiL2BrTpPortOutFrames Counter, atiL2BrTpPortInDiscards Counter } atiL2BrTpPortLanId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object uniquely identifies the lan or Virtual lan." ::= { atiL2BrTpPortEntry 1 } atiL2BrTpPort OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-only STATUS mandatory DESCRIPTION "The port number of the port for which this entry contains Transparent bridging management information." ::= { atiL2BrTpPortEntry 2 } -- It would be nice if we could use ifMtu as the size of the -- largest INFO field, but we can't because ifMtu is defined -- to be the size that the (inter-)network layer can use which -- can differ from the MAC layer (especially if several layers -- of encapsulation are used). atiL2BrTpPortMaxInfo OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The maximum size of the INFO (non-MAC) field that this port will receive or transmit." ::= { atiL2BrTpPortEntry 3 } atiL2BrTpPortInFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames that have been received by this port from its segment. Note that a frame received on the interface corresponding to this port is only counted by this object if and only if it is for a protocol being processed by the local bridging function, including bridge management frames." REFERENCE "IEEE 802.1D-1990: Section 6.6.1.1.3" ::= { atiL2BrTpPortEntry 4 } atiL2BrTpPortOutFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames that have been transmitted by this port to its segment. Note that a frame transmitted on the interface corresponding to this port is only counted by this object if and only if it is for a protocol being processed by the local bridging function, including bridge management frames." REFERENCE "IEEE 802.1D-1990: Section 6.6.1.1.3" ::= { atiL2BrTpPortEntry 5 } atiL2BrTpPortInDiscards OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of valid frames received which were discarded (i.e., filtered) by the Forwarding Process." REFERENCE "IEEE 802.1D-1990: Section 6.6.1.1.3" ::= { atiL2BrTpPortEntry 6 } -- -- atiL2QOSConfigGroup (applicable only to at-8326GB, at-9410GB and at-8350GB) -- atiL2QOSStatus OBJECT-TYPE SYNTAX INTEGER{ enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "If the QOS status is enabled, then QOS packets will be assigned to high or low priority queue. If it is disabled, packets works normally.(Applicable only to at-8326GB, at-9410GB and at-8350GB)" ::= { atiL2QOSConfigGroup 1 } atiL2TrafficMappingTable OBJECT-TYPE SYNTAX SEQUENCE OF AtiL2TrafficMappingEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "It contains the mapping of all traffic classes and their priority assignments.(Applicable only to at-8326GB, at-9410GB and at-8350GB)" ::= { atiL2QOSConfigGroup 2 } atiL2TrafficMappingEntry OBJECT-TYPE SYNTAX AtiL2TrafficMappingEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry maps a traffic class to the priority queue to be used for it's packets. (Applicable only to at-8326GB, at-9410GB and at-8350GB)" INDEX { atiL2TrafficClassIndex } ::= { atiL2TrafficMappingTable 1 } AtiL2TrafficMappingEntry ::= SEQUENCE { atiL2TrafficClassIndex INTEGER, atiL2PriorityQueue INTEGER } atiL2TrafficClassIndex OBJECT-TYPE SYNTAX INTEGER(0..7) ACCESS read-only STATUS mandatory DESCRIPTION "The Index of the traffic class. It is obtained from the packet format.(Applicable only to at-8326GB, at-9410GB and at-8350GB)" ::= { atiL2TrafficMappingEntry 1 } atiL2PriorityQueue OBJECT-TYPE SYNTAX INTEGER{ lowest(0), low(1), high(2), highest(3) } ACCESS read-write STATUS mandatory DESCRIPTION "The priority queue to be used to forward packets. (Applicable only to at-8326GB, at-9410GB and at-8350GB)" ::= { atiL2TrafficMappingEntry 2 } END