XYLAN-DS3-MIB DEFINITIONS ::= BEGIN -- RCSID information -- $RCSfile: xylan-ds3.mib,v $ -- $Revision: 1.9 $ $State: Exp $ -- $Date: 1998/06/05 16:56:33 $ -- $Author: eric $ -- xylan-ds3.mib -- Revision: 1.00 -- Date: April 1, 1997 -- Alcatel Internetworking, Inc. -- 26801 W. Agoura Road -- Calabasas, CA 91301 -- (818) 880-3500 -- support@ind.alcatel.com -- This module provides authoritative definitions for Alcatel Internetworking, Inc. -- enterprise-specific physical port parameters MIB. -- This module will be extended, as needed. -- Alcatel Internetworking, Inc. reserves the right to make changes in -- specification and other information contained in this document -- without prior notice. The reader should consult Alcatel Internetworking, -- Inc. to determine whether any such changes have been made. -- In no event shall Alcatel Internetworking, Inc. be liable for any incidental, -- indirect, special, or consequential damages whatsoever (including -- but not limited to lost profits) arising out of or related to this -- document or the information contained in it, even if Alcatel Internetworking, -- Inc. has been advised of, known, or should have known, the -- possibility of such damages. -- Alcatel Internetworking, Inc. grants vendors, end-users, and other interested -- parties a non-exclusive license to use this Specification in connection -- with the management of Alcatel Internetworking, Inc. products. -- Copyright (C) 1997, Alcatel Internetworking, Inc. All Rights Reserved. IMPORTS Counter, TimeTicks FROM RFC1155-SMI DisplayString, transmission FROM RFC1213-MIB OBJECT-TYPE FROM RFC-1212 xylanPportArch FROM XYLAN-BASE-MIB ; dsx3Port OBJECT IDENTIFIER ::= { xylanPportArch 2 } -- DS3/E3 Physical Port Configuration Table dsx3PortConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF Dsx3PortConfigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table of DS3/E3 physical layer status and parameter information." ::= { dsx3Port 1 } dsx3PortConfigEntry OBJECT-TYPE SYNTAX Dsx3PortConfigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the table, containing information about the physical layer of a DS3/E3 interface." INDEX { dsx3PortConfigSlotIndex, dsx3PortConfigPortIndex } ::= { dsx3PortConfigTable 1 } Dsx3PortConfigEntry ::= SEQUENCE { dsx3PortConfigSlotIndex INTEGER, dsx3PortConfigPortIndex INTEGER, dsx3PortConfigIfType INTEGER, dsx3PortConfigTcSubLayer INTEGER, dsx3PortConfigPlcpStatus INTEGER, dsx3PortConfigFEAC INTEGER, dsx3PortConfigNatUse INTEGER, dsx3PortConfigRxPayloadType INTEGER, dsx3PortConfigTimeMarker INTEGER, dsx3PortConfigTxPayloadType INTEGER, dsx3PortConfigExpectedPayloadType INTEGER, dsx3PortConfigTxTrailTraceID DisplayString, dsx3PortConfigRxTrailTraceID DisplayString, dsx3PortConfigExpectedTrailTraceID DisplayString, dsx3PortConfigLineStatus INTEGER, dsx3PortConfigPlScramble INTEGER } dsx3PortConfigSlotIndex OBJECT-TYPE SYNTAX INTEGER (1..9) ACCESS read-only STATUS mandatory DESCRIPTION "A unique value which identifies this HSM board slot." ::= { dsx3PortConfigEntry 1 } dsx3PortConfigPortIndex OBJECT-TYPE SYNTAX INTEGER (1..32) ACCESS read-only STATUS mandatory DESCRIPTION "A unique value which identifies this port." ::= { dsx3PortConfigEntry 2 } dsx3PortConfigIfType OBJECT-TYPE SYNTAX INTEGER { ds3(1), e3(2) } ACCESS read-only STATUS mandatory DESCRIPTION "This objects indicates type of interface." ::= { dsx3PortConfigEntry 3 } dsx3PortConfigTcSubLayer OBJECT-TYPE SYNTAX INTEGER { none (1), plcp (2), adm (3) } ACCESS read-write STATUS mandatory DESCRIPTION "The type of specific Transmission Convergence sublayer used on this port. Each option is described as follows: none - specific sublayer is not present. plcp - Physical Layer Convergence Protocol. adm - ATM Direct Mapping." ::= { dsx3PortConfigEntry 4 } dsx3PortConfigPlcpStatus OBJECT-TYPE SYNTAX INTEGER(1..15) ACCESS read-only STATUS mandatory DESCRIPTION "This object indicates current status of PLCP. This object only applies to port which sublayer is configured to PLCP. A value of 1 is returned for other cases. The dsx3PortStatsPlcpStatus is a bit map represented as a sum, therfore it can represent multiple alarms. 1 - plcpNoAlarm No alarm present 2 - plcpOof Out of frame 4 - plcpLof Loss of frame 8 - plcpYellow Receive yellow alarm from far-end" ::= { dsx3PortConfigEntry 5 } dsx3PortConfigFEAC OBJECT-TYPE SYNTAX INTEGER { dsx3NoFEAC (1), dsx3DS3EquipmentFailure (2), dsx3DS3LOS (3), dsx3DS3OutofFrame (4), dsx3DS3AISreceived (5), dsx3DS3IDLEreceived (6), dsx3DS3NonServiceAffectingEquipFailure (7), dsx3CommonEquipmentFailure (8), dsx3DS3LoopbackReceived (9), dsx3DS1ServiceAffectingEquipmentFailure (10), dsx3DS1NonServiceAffectingEquipFailure (11), dsx3SingleDS1LOS (12), dsx3MultipleDS1sLOS (13), dsx3UnknownCode (14), dsx3UnsupportedCode (15) } ACCESS read-only STATUS mandatory DESCRIPTION "This object indicates the presence FEAC being received by this port. This object only applies to DS3 interface with framing format configured to C-bit parity. A value of dsx3NoFEAC(1) is returned for other cases." ::= { dsx3PortConfigEntry 6 } dsx3PortConfigNatUse OBJECT-TYPE SYNTAX INTEGER { one (1), zero (2) } ACCESS read-only STATUS mandatory DESCRIPTION "The object indicates current state of National Use Bit which is bit 12 of G.751 frame. This object only applies to E3 port which line framimg is configured to G.751. A value of one(1) is returned for other sublayers or DS3 port." ::= { dsx3PortConfigEntry 7 } dsx3PortConfigRxPayloadType OBJECT-TYPE SYNTAX INTEGER { unknown-or-not-applicable(1), unequipped(2), atm(3), equipped-non-specific(4), sdh-tu-12s(5) } ACCESS read-only STATUS mandatory DESCRIPTION "The object indicates current state of payload type bits (bit 3,4,5 of Maintenance and Adaptation byte) of an E3 G.832 frame. This objects only applies to E3 port which framing is configured to G.832. A value of 1 is returned for all other cases." ::= { dsx3PortConfigEntry 8 } dsx3PortConfigTimeMarker OBJECT-TYPE SYNTAX INTEGER { one (1), zero (2) } ACCESS read-only STATUS mandatory DESCRIPTION "The object indicates current state of Timing Marker bit (bit 8 of Maintenanc and Adaptation byte) of an E3 G.832 frame. This objects only applies to E3 port which framing is configured to G.832. A value of one(1) is returned for other cases." ::= { dsx3PortConfigEntry 9 } dsx3PortConfigTxPayloadType OBJECT-TYPE SYNTAX INTEGER { unequipped(1), atm(2), equipped-non-specific(3), sdh-tu-12s(4) } ACCESS read-write STATUS mandatory DESCRIPTION "The object reflects the value to be inserted in the payload type bits (bit 3,4,5 of Maintenance and Adaptation byte) of an E3 G.832 frame. This objects only applies to E3 port whose framing is configured as G.832. Additionally if this object is not applicable, i.e. not E3 G.832, writing to this object will be silently ignored." ::= { dsx3PortConfigEntry 10 } dsx3PortConfigExpectedPayloadType OBJECT-TYPE SYNTAX INTEGER { unequipped(1), atm(2), equipped-non-specific(3), sdh-tu-12s(4) } ACCESS read-write STATUS mandatory DESCRIPTION "The object indicates the current expected payload type bits (bit 3,4,5 of Maintenance and Adaptation byte) of an E3 G.832 frame. This objects only applies to E3 port whose framing is configured as G.832. Additionally if this object is not applicable, i.e. not E3 G.832, writing to this object will be silently ignored." ::= { dsx3PortConfigEntry 11 } dsx3PortConfigTxTrailTraceID OBJECT-TYPE SYNTAX DisplayString (SIZE (0..15)) ACCESS read-write STATUS mandatory DESCRIPTION "The object indicates the characters to be inserted as Trail Trace Identifier of an E3 G.832 frame. This object only applies to E3 port whose framing is configured as G.832. A binary 0 in the first octet indicates all zeros insertion, or this port is not configured as E3 G.832 framing. Additionally if this object is not applicable, i.e. not E3 G.832, writing to this object will be silently ignored." ::= { dsx3PortConfigEntry 12 } dsx3PortConfigRxTrailTraceID OBJECT-TYPE SYNTAX DisplayString (SIZE (0..15)) ACCESS read-only STATUS mandatory DESCRIPTION "The object indicates the current characters received as Trail Trace Identifier of an E3 G.832 frame. This object only applies to E3 port whose framing is configured as G.832. A binary 0 in the first octet indicates all zeros insertion received or this port is not configured as E3 G.832 framing." ::= { dsx3PortConfigEntry 13 } dsx3PortConfigExpectedTrailTraceID OBJECT-TYPE SYNTAX DisplayString (SIZE (0..15)) ACCESS read-write STATUS mandatory DESCRIPTION "The object indicates the expected characters received as Trail Trace Identifier of an E3 G.832 frame. This object only applies to E3 port whose framing is configured as G.832. A binary 0 in the first octet indicates all zeros insertion, or this port is not configured as E3 G.832 framing. Additionally if this object is not applicable, i.e. not E3 G.832, writing to this object will be silently ignored." ::= { dsx3PortConfigEntry 14 } dsx3PortConfigLineStatus OBJECT-TYPE SYNTAX INTEGER (1..2097151) ACCESS read-only STATUS mandatory DESCRIPTION "This object indicates the line status of a ds3/e3 interface. Each bit position (bit-0 to bit-18) represents one failure condition of the interface. Bit-19 and bit-20 are used to represent Timing Marker bit and National Use bit. Note that the SYNTAX type of Counter instead of INTEGER is used here as there are more than 16 different conditions to represent. The followings define the various bit position and their meanings: Bit Description 0: No alarm present 1: Out of Frame Alarm received 2: Loss Of Signal Alarm received 3: Alarm Indication Signal Alarm received 4: Red Alarm received 5: Far End Receive Failure Alarm received (Non E3 G.751 only) Remote Alarm Indication Alarm received (E3 G.751 only) 6: Change Of Frame Alignment Alarm received 7: PLCP Out Of Frame Alarm received 8: PLCP Yellow Alarm received 9: PLCP Framing Bit Error Alarm received 10: PLCP Bit Interleaved Parity Error Alarm received 11: PLCP Loss Of Frames Alarm received 12: PLCP Far End Block Error Alarm received 13: Cell Loss Alarm received 14: Far End Block Error Alarm received 15: Parity Error Alarm received 16: Trail Trace ID Mismatch Alarm received (E3 G.832 only) 17: Rx Payload Type Mismatch Alarm received (E3 G.832 only) 18: Unequipped Payload Type received (E3 G.832 only) 19: Timing Marker Bit (bit 8 of the E3 G.832 Maintenance and Adaptation bye) received. 20: National Use bit (bit 12 of the frame in a E3 G.751 frame) received." ::= { dsx3PortConfigEntry 15 } dsx3PortConfigPlScramble OBJECT-TYPE SYNTAX INTEGER { false(1), true(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Payload Scrambling Enable." ::= { dsx3PortConfigEntry 16 } -- DS3/E3 Physical Port Statistics Table dsx3PortStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF Dsx3PortStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table of DS3/E3 physical port statistics." ::= { dsx3Port 2 } dsx3PortStatsEntry OBJECT-TYPE SYNTAX Dsx3PortStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the table, containing information about the physical port statistics of a DS3/E3 interface." INDEX { dsx3PortStatsSlotIndex, dsx3PortStatsPortIndex } ::= { dsx3PortStatsTable 1 } Dsx3PortStatsEntry ::= SEQUENCE { dsx3PortStatsSlotIndex INTEGER, dsx3PortStatsPortIndex INTEGER, dsx3PortStatsLossOfSignal Counter, dsx3PortStatsOutOfFrame Counter, dsx3PortStatsAISEvent Counter, dsx3PortStatsRedAlarmEvent Counter, dsx3PortStatsFarEndReceiveError Counter, dsx3PortStatsFarEndBlkError Counter, dsx3PortStatsLineCodeVioEvent Counter, dsx3PortStatsFramingBitError Counter, dsx3PortStatsChangeOfFrameAlign Counter, dsx3PortStatsParityBitError Counter, dsx3PortStatsPathParityBitError Counter, dsx3PortStatsPlcpLossOfFrame Counter, dsx3PortStatsPlcpOutOfFrame Counter, dsx3PortStatsPlcpYellowAlarm Counter, dsx3PortStatsPlcpFarEndBlkError Counter, dsx3PortStatsPlcpFramingError Counter, dsx3PortStatsPlcpBIPError Counter, dsx3PortStatsPayloadTypeMismatchError Counter, dsx3PortStatsUnequippedError Counter, dsx3PortStatsTrailTraceIDMismatchError Counter } dsx3PortStatsSlotIndex OBJECT-TYPE SYNTAX INTEGER (1..9) ACCESS read-only STATUS mandatory DESCRIPTION "A unique value which identifies this HSM board slot." ::= { dsx3PortStatsEntry 1 } dsx3PortStatsPortIndex OBJECT-TYPE SYNTAX INTEGER (1..32) ACCESS read-only STATUS mandatory DESCRIPTION "A unique value which identifies this port." ::= { dsx3PortStatsEntry 2 } dsx3PortStatsLossOfSignal OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of Loss of Signals that have been detected on this port." ::= { dsx3PortStatsEntry 3 } dsx3PortStatsOutOfFrame OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of Out of Frames that have been detected on this port." ::= { dsx3PortStatsEntry 4 } dsx3PortStatsAISEvent OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of AIS events that have been detected on this port." ::= { dsx3PortStatsEntry 5 } dsx3PortStatsRedAlarmEvent OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of Red Alarm events that have been detected on this port. This object only applies to DS3 interface." ::= { dsx3PortStatsEntry 6 } dsx3PortStatsFarEndReceiveError OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of Far-end Receive Error events that have been received on this port." ::= { dsx3PortStatsEntry 7 } dsx3PortStatsFarEndBlkError OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of Far-end Block Error events that have been received on this port." ::= { dsx3PortStatsEntry 8 } dsx3PortStatsLineCodeVioEvent OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of Line Code Violation events that have been received on this port. This is a count of both Bipolar Violation (BPV) and Excessive zeros (EXZs)." ::= { dsx3PortStatsEntry 9 } dsx3PortStatsFramingBitError OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of Framing Bit Error events that have been detected on this port." ::= { dsx3PortStatsEntry 10 } dsx3PortStatsChangeOfFrameAlign OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of Change of Frame Alignment events that have been detected on this port." ::= { dsx3PortStatsEntry 11 } dsx3PortStatsParityBitError OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of parity bit errors that have been detected on this port." ::= { dsx3PortStatsEntry 12 } dsx3PortStatsPathParityBitError OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of path parity bit errors that have been detected on this port." ::= { dsx3PortStatsEntry 13 } dsx3PortStatsPlcpLossOfFrame OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of PLCP loss of frame events that have been detected on this port. A value of zero is returned if port sublayer is not PLCP." ::= { dsx3PortStatsEntry 14 } dsx3PortStatsPlcpOutOfFrame OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of PLCP out of frame events that have been detected on this port. A value of zero is returned if port sublayer is not PLCP." ::= { dsx3PortStatsEntry 15 } dsx3PortStatsPlcpYellowAlarm OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of PLCP Yellow Alarms that have been detected on this port. A value of zero is returned if port sublayer is not PLCP." ::= { dsx3PortStatsEntry 16 } dsx3PortStatsPlcpFarEndBlkError OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of PLCP Far-end Block Errors that have been detected on this port. A value of zero is returned if port sublayer is not PLCP." ::= { dsx3PortStatsEntry 17 } dsx3PortStatsPlcpFramingError OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of PLCP Framing Octet Errors that have been detected on this port. A value of zero is returned if port sublayer is not PLCP." ::= { dsx3PortStatsEntry 18 } dsx3PortStatsPlcpBIPError OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of PLCP Bit Interleaved Parity Errors that have been detected on this port. A value of zero is returned if port sublayer is not PLCP." ::= { dsx3PortStatsEntry 19 } dsx3PortStatsPayloadTypeMismatchError OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of payload type mismatch failure that have been detected on this port. This object is applicable to E3 G.832 only. A value of zero is returned if the port is not configured as E3 and G.832." ::= { dsx3PortStatsEntry 20 } dsx3PortStatsUnequippedError OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of unequipped failure that have been detected on this port. This object is applicable to E3 G.832 only. A value of zero is returned if the port is not configured as E3 and G.832." ::= { dsx3PortStatsEntry 21 } dsx3PortStatsTrailTraceIDMismatchError OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of trail trace identification mismatch failure that have been detected on this port. This object is applicable to E3 G.832 only. A value of zero is returned if the port is not configured as E3 and G.832." ::= { dsx3PortStatsEntry 22 } -- DS3/E3 Physical Port Interval Statistics Table dsx3PortIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF Dsx3PortIntervalEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table of DS3/E3 physical port statistics." ::= { dsx3Port 3 } dsx3PortIntervalEntry OBJECT-TYPE SYNTAX Dsx3PortIntervalEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the table, containing information about the physical port statistics of a DS3/E3 interface." INDEX { dsx3PortIntervalSlotIndex, dsx3PortIntervalPortIndex } ::= { dsx3PortIntervalTable 1 } Dsx3PortIntervalEntry ::= SEQUENCE { dsx3PortIntervalSlotIndex INTEGER, dsx3PortIntervalPortIndex INTEGER, dsx3PortIntervalClear INTEGER, dsx3PortIntervalLastClear TimeTicks, dsx3PortIntervalLossOfSignal Counter, dsx3PortIntervalOutOfFrame Counter, dsx3PortIntervalAISEvent Counter, dsx3PortIntervalRedAlarmEvent Counter, dsx3PortIntervalFarEndReceiveError Counter, dsx3PortIntervalFarEndBlkError Counter, dsx3PortIntervalLineCodeVioEvent Counter, dsx3PortIntervalFramingBitError Counter, dsx3PortIntervalChangeOfFrameAlign Counter, dsx3PortIntervalParityBitError Counter, dsx3PortIntervalPathParityBitError Counter, dsx3PortIntervalPlcpLossOfFrame Counter, dsx3PortIntervalPlcpOutOfFrame Counter, dsx3PortIntervalPlcpYellowAlarm Counter, dsx3PortIntervalPlcpFarEndBlkError Counter, dsx3PortIntervalPlcpFramingError Counter, dsx3PortIntervalPlcpBIPError Counter, dsx3PortIntervalPayloadTypeMismatchError Counter, dsx3PortIntervalUnequippedError Counter, dsx3PortIntervalTrailTraceIDMismatchError Counter } dsx3PortIntervalSlotIndex OBJECT-TYPE SYNTAX INTEGER (1..9) ACCESS read-only STATUS mandatory DESCRIPTION "A unique value which identifies this HSM board slot." ::= { dsx3PortIntervalEntry 1 } dsx3PortIntervalPortIndex OBJECT-TYPE SYNTAX INTEGER (1..32) ACCESS read-only STATUS mandatory DESCRIPTION "A unique value which identifies this port." ::= { dsx3PortIntervalEntry 2 } dsx3PortIntervalClear OBJECT-TYPE SYNTAX INTEGER { noAction(1), clearRequest(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This object allows clearing all interval statistics of this port to value of zero. Setting this object to clearRequest will initiate managed entity to clear the statistics of this table." ::= { dsx3PortIntervalEntry 3 } dsx3PortIntervalLastClear OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "The value of MIB II's sysUpTime object at the time this table statistics is cleared." ::= { dsx3PortIntervalEntry 4 } dsx3PortIntervalLossOfSignal OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of Loss of Signals that have been detected on this port since it's cleared by the managing station." ::= { dsx3PortIntervalEntry 5 } dsx3PortIntervalOutOfFrame OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of Out of Frames that have been detected on this port since it's cleared by the managing station." ::= { dsx3PortIntervalEntry 6 } dsx3PortIntervalAISEvent OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of AIS events that have been detected on this port since it's cleared by the managing station." ::= { dsx3PortIntervalEntry 7 } dsx3PortIntervalRedAlarmEvent OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of Red Alarm events that have been detected on this port since it's cleared by the managing station. This object only applies to DS3 interface." ::= { dsx3PortIntervalEntry 8 } dsx3PortIntervalFarEndReceiveError OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of far-end receive error events that have been received on this port since it's cleared by the managing station." ::= { dsx3PortIntervalEntry 9 } dsx3PortIntervalFarEndBlkError OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of far-end block error events that have been received on this port since it's cleared by the managing station." ::= { dsx3PortIntervalEntry 10 } dsx3PortIntervalLineCodeVioEvent OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of line code violation events that have been received on this port. This is a count of both Bipolar Violation (BPV) and Excessive zeros (EXZs) since it's cleared by the managing station." ::= { dsx3PortIntervalEntry 11 } dsx3PortIntervalFramingBitError OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of Framing Bit Error events that have been detected on this port since it's cleared by the managing station." ::= { dsx3PortIntervalEntry 12 } dsx3PortIntervalChangeOfFrameAlign OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of change of frame alignment events that have been detected on this port since it's cleared by the managing station." ::= { dsx3PortIntervalEntry 13 } dsx3PortIntervalParityBitError OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of parity bit errors that have been detected on this port since it's cleared by the managing station." ::= { dsx3PortIntervalEntry 14 } dsx3PortIntervalPathParityBitError OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of path parity bit errors that have been detected on this port since it's cleared by the managing station." ::= { dsx3PortIntervalEntry 15 } dsx3PortIntervalPlcpLossOfFrame OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of PLCP loss of frame events that have been detected on this port since it's cleared by the managing station. A value of zero is returned if port sublayer is not PLCP. " ::= { dsx3PortIntervalEntry 16 } dsx3PortIntervalPlcpOutOfFrame OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of PLCP out of frame events that have been detected on this port since it's cleared by the managing station. A value of zero is returned if port sublayer is not PLCP. " ::= { dsx3PortIntervalEntry 17 } dsx3PortIntervalPlcpYellowAlarm OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of PLCP Yellow Alarms that have been detected detected on this port since it's cleared by the managing station. A value of zero is returned if port sublayer is not PLCP. " ::= { dsx3PortIntervalEntry 18 } dsx3PortIntervalPlcpFarEndBlkError OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of PLCP Far-end Block Errors that have been detected on this port since it's cleared by the managing station. A value of zero is returned if port sublayer is not PLCP. " ::= { dsx3PortIntervalEntry 19 } dsx3PortIntervalPlcpFramingError OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of PLCP Framing Octet Errors that have been detected on this port since it's cleared by the managing station. A value of zero is returned if port sublayer is not PLCP. " ::= { dsx3PortIntervalEntry 20 } dsx3PortIntervalPlcpBIPError OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of PLCP Bit Interleaved Parity Errors that have detected on this port since it's cleared by the managing station. A value of zero is returned if port sublayer is not PLCP. " ::= { dsx3PortIntervalEntry 21 } dsx3PortIntervalPayloadTypeMismatchError OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of payload type mismatch failure that have been detected on this port since it's cleared by the managing station. This object is applicable to E3 G.832 only. A value of zero is returned if the port is not configured as E3 and G.832." ::= { dsx3PortIntervalEntry 22 } dsx3PortIntervalUnequippedError OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of unequipped failure that have been detected on this port sinece it's cleared by the managing station. This object is applicable to E3 G.832 only. A value of zero is returned if the port is not configured as E3 and G.832." ::= { dsx3PortIntervalEntry 23 } dsx3PortIntervalTrailTraceIDMismatchError OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of trail trace identification mismatch failure that have been detected on this port since it's cleared by the managing station. This object is applicable to E3 G.832 only. A value of zero is returned if the port is not configured as E3 and G.832." ::= { dsx3PortIntervalEntry 24 } END