NETGEAR-DHCPSERVER-PRIVATE-MIB DEFINITIONS ::= BEGIN -- NETGEAR DHCP Server MIB -- Copyright LVL7 Systems (2002-2005) All rights reserved. -- This SNMP Management Information Specification -- embodies LVL7 System's confidential and proprietary -- intellectual property. LVL7 Systems retains all title -- and ownership in the Specification including any revisions. -- This Specification is supplied "AS IS", LVL7 Systems -- makes no warranty, either expressed or implied, -- as to the use, operation, condition, or performance of the -- Specification. IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, IpAddress, Integer32, Unsigned32, TimeTicks, Counter32 FROM SNMPv2-SMI TEXTUAL-CONVENTION, RowStatus, RowPointer, MacAddress, StorageType, TruthValue FROM SNMPv2-TC DisplayString, PhysAddress FROM RFC1213-MIB ng7000Switch FROM NETGEAR-REF-MIB; agentDHCPServerPrivate MODULE-IDENTITY LAST-UPDATED "200502231200Z" -- 23 Feb 2005 12:00:00 GMT ORGANIZATION "Netgear" CONTACT-INFO "" DESCRIPTION "The NETGEAR Private MIB for DHCP Server" -- revision history REVISION "200502231200Z" -- 23 Feb 2005 12:00:00 GMT DESCRIPTION "Initial revision." ::= { ng7000Switch 12 } --************************************************************************************** -- agentDhcpServerGroup -> contains MIB objects displaying various properties of a DHCP server -- --************************************************************************************** agentDhcpServerGroup OBJECT IDENTIFIER ::= { agentDHCPServerPrivate 1 } agentDhcpServerAdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION " Admin-mode of the DHCP Server." DEFVAL { disable } ::= { agentDhcpServerGroup 1 } agentDhcpServerPingPktNos OBJECT-TYPE SYNTAX INTEGER (0 | 2..10) MAX-ACCESS read-write STATUS current DESCRIPTION " The no. of packets a DHCP Server sends to a pool address as part of a ping operation.Setting the value of ping-packets to zero turns off DHCP Server ping operation ." DEFVAL { 2 } ::= { agentDhcpServerGroup 2 } agentDhcpServerAutomaticBindingsNos OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of IP addresses that have been assigned automatically." ::= { agentDhcpServerGroup 3 } agentDhcpServerExpiredBindingsNos OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of expired leases." ::= { agentDhcpServerGroup 4 } agentDhcpServerMalformedMessagesReceived OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of malformed(truncated or corrupt) messages that have been received by the DHCP server." ::= { agentDhcpServerGroup 5 } agentDhcpServerDISCOVERMessagesReceived OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of DHCP messages of type DHCPDISCOVER that have been received by the DHCP server." ::= { agentDhcpServerGroup 6 } agentDhcpServerREQUESTMessagesReceived OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of DHCP messages of type DHCPREQUEST that have been received by the DHCP server." ::= { agentDhcpServerGroup 7 } agentDhcpServerDECLINEMessagesReceived OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of DHCP messages of type DHCPDECLINE that have been received by the DHCP server." ::= { agentDhcpServerGroup 8 } agentDhcpServerRELEASEMessagesReceived OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of DHCP messages of type DHCPRELEASE that have been received by the DHCP server." ::= { agentDhcpServerGroup 9 } agentDhcpServerINFORMMessagesReceived OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of DHCP messages of type DHCPINFORM that have been received by the DHCP server." ::= { agentDhcpServerGroup 10 } agentDhcpServerOFFERMessagesSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of DHCP messages of type DHCPOFFER that have been sent by the DHCP server." ::= { agentDhcpServerGroup 11 } agentDhcpServerACKMessagesSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of DHCP messages of type DHCPACK that have been sent by the DHCP server." ::= { agentDhcpServerGroup 12 } agentDhcpServerNAKMessagesSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of DHCP messages of type DHCPNAK that have been sent by the DHCP server." ::= { agentDhcpServerGroup 13 } agentDhcpServerClearStatistics OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION " Clears the DHCP server statistics." DEFVAL { disable } ::= { agentDhcpServerGroup 14 } agentDhcpServerBootpAutomatic OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Used to enable or disable autmatic address allocation to bootp clients from dynamic address pools." DEFVAL { disable } ::= { agentDhcpServerGroup 15 } --********************************************************************************** -- agentDhcpServerPoolConfigGroup -- This group contains three tables : agentDhcpServerPoolConfigTable, -- agentDhcpServerBindingTable, -- -- agentDhcpServerPoolConfigTable -> This table is used to configure a -- new DHCP address pool on a DHCP server. This table -- is also used to delete a configured DHCP address pool. -- -- agentDhcpServerPoolAllocationTable -> This table is used to configure a DHCP address -- pool for dynamic and manual allocations. -- -- agentDhcpServerExcludedAddressRangeTable -> This table lists the excluded-address ranges -- for a DHCP Server -- -- agentDhcpServerPoolOptionTable -> Table for DHCP Server options --********************************************************************************** agentDhcpServerPoolConfigGroup OBJECT IDENTIFIER ::= { agentDHCPServerPrivate 2 } agentDhcpServerPoolNameCreate OBJECT-TYPE SYNTAX DisplayString (SIZE(0|1..31)) MAX-ACCESS read-write STATUS current DESCRIPTION "A pool is created by applying write operation on this MIB object and providing a new pool-name. Get operation on this MIB object returns a null-value, as for the purpose of viewing the pool name, the user should perform the traversal of agentDhcpServerPoolConfigTable. For this reason the get operation on object agentDhcpServerPoolNameCreate becomes insignificant." ::= { agentDhcpServerPoolConfigGroup 1 } agentDhcpServerPoolConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentDhcpServerPoolConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the DHCP Server Pool configuration entries." ::= { agentDhcpServerPoolConfigGroup 2 } agentDhcpServerPoolConfigEntry OBJECT-TYPE SYNTAX AgentDhcpServerPoolConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents entry for a Dhcp server pool." INDEX { agentDhcpServerPoolIndex } ::= { agentDhcpServerPoolConfigTable 1 } AgentDhcpServerPoolConfigEntry ::= SEQUENCE { agentDhcpServerPoolIndex Unsigned32, agentDhcpServerPoolName DisplayString, agentDhcpServerPoolDefRouter DisplayString, agentDhcpServerPoolDNSServer DisplayString, agentDhcpServerPoolLeaseTime Integer32, agentDhcpServerPoolType INTEGER, agentDhcpServerPoolNetbiosNameServer DisplayString, agentDhcpServerPoolNetbiosNodeType INTEGER, agentDhcpServerPoolNextServer IpAddress, agentDhcpServerPoolDomainName DisplayString, agentDhcpServerPoolBootfile DisplayString, agentDhcpServerPoolRowStatus RowStatus } agentDhcpServerPoolIndex OBJECT-TYPE SYNTAX Unsigned32 (1..512) MAX-ACCESS read-only STATUS current DESCRIPTION "The Pool Index, which 'll be used as index for the PoolConfig Table." ::= { agentDhcpServerPoolConfigEntry 1 } agentDhcpServerPoolName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..31)) MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the DHCP Address pool. This value cannot be modified" ::= { agentDhcpServerPoolConfigEntry 2 } agentDhcpServerPoolDefRouter OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies the default-router list(each default-router is separated by comma and the list is terminated by semi-colon) for a DHCP client, an example would be 10.10.1.1,192.168.36.1,157.227.44.1;(no spaces in between).User should enter a 'null' or 'NULL' string to remove current default-router list." ::= { agentDhcpServerPoolConfigEntry 3 } agentDhcpServerPoolDNSServer OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies the DNS IP servers(each DNS IP server is separated by comma and the list is terminated by semi-colon) for a DHCP client, an example would be 10.10.1.1,192.168.36.1,157.227.44.1;(no spaces in between).User should enter a 'null' or 'NULL' string to remove current default-router list." ::= { agentDhcpServerPoolConfigEntry 4 } agentDhcpServerPoolLeaseTime OBJECT-TYPE SYNTAX Integer32 (1..86400) MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies the duration of the lease(in minutes) for an IP address that is assigened from a DHCP server to a DHCP client. For infinite leases, lease-time value will be set to 86400." ::= { agentDhcpServerPoolConfigEntry 5 } agentDhcpServerPoolType OBJECT-TYPE SYNTAX INTEGER{ un-allocated(0), dynamic(1), manual(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This specifies the type of the binding that is associated with this pool." ::= { agentDhcpServerPoolConfigEntry 6 } agentDhcpServerPoolNetbiosNameServer OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies the IP address-list of Net BIOS name-servers that are available to DHCP clients (each IP address in this list is separated by comma and the list is terminated by semi-colon), an example would be 10.10.1.1,192.168.36.1,157.227.44.1;(no spaces in between).User should enter a 'null' or 'NULL' string to remove current Net BIOS name-server list." ::= { agentDhcpServerPoolConfigEntry 7 } agentDhcpServerPoolNetbiosNodeType OBJECT-TYPE SYNTAX INTEGER { none(0), b-node(1), p-node(2), m-node(4), h-node(8) } MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies the NetBIOS node-type for DHCP clients. 'none' is shown if node-type is not set to any of the four values." ::= { agentDhcpServerPoolConfigEntry 8 } agentDhcpServerPoolNextServer OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This configures the next server in the boot-process of a DHCP clients.User should enter zero(0.0.0.0) to remove the current Next-server address" ::= { agentDhcpServerPoolConfigEntry 9 } agentDhcpServerPoolDomainName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..255)) MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies the domain-name for a DHCP client. User should enter a 'null' or 'NULL' string to remove specified domain-name." ::= { agentDhcpServerPoolConfigEntry 10 } agentDhcpServerPoolBootfile OBJECT-TYPE SYNTAX DisplayString (SIZE(1..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies the name of the default boot image for a DHCP client.User should enter a 'null' or 'NULL' string to remove specified bootfile name." ::= { agentDhcpServerPoolConfigEntry 11 } agentDhcpServerPoolRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The row status variable is used according to installation and removal conventions for conceptual rows. When a pool is created by applying write operation on 'agentDhcpServerPoolCreateName',row-status becomes 'active'. If row-status for a poolEntry is set to 'destroy', the corresponding pool gets deleted. " ::= { agentDhcpServerPoolConfigEntry 12 } --********************************************************************************** agentDhcpServerPoolAllocationTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentDhcpServerPoolAllocationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the DHCP Server's pool entries, showing the binding(dynamic/manual) specific parameters." ::= { agentDhcpServerPoolConfigGroup 3 } agentDhcpServerPoolAllocationEntry OBJECT-TYPE SYNTAX AgentDhcpServerPoolAllocationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents entry for a Dhcp server's allocation pool." AUGMENTS { agentDhcpServerPoolConfigEntry } ::= { agentDhcpServerPoolAllocationTable 1 } -- All objects are of type read-write AgentDhcpServerPoolAllocationEntry ::= SEQUENCE { agentDhcpServerPoolAllocationName DisplayString, agentDhcpServerDynamicPoolIpAddress IpAddress, agentDhcpServerDynamicPoolIpMask IpAddress, agentDhcpServerDynamicPoolIpPrefixLength Unsigned32, agentDhcpServerPoolAllocationType INTEGER, agentDhcpServerManualPoolClientIdentifier DisplayString, agentDhcpServerManualPoolClientName DisplayString, agentDhcpServerManualPoolClientHWAddr MacAddress, agentDhcpServerManualPoolClientHWType INTEGER, agentDhcpServerManualPoolIpAddress IpAddress, agentDhcpServerManualPoolIpMask IpAddress, agentDhcpServerManualPoolIpPrefixLength Unsigned32 } agentDhcpServerPoolAllocationName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..30)) MAX-ACCESS read-only STATUS current DESCRIPTION "This specifies name of the DHCP Address pool having dynamic binding. This value is same as agentDhcpServerPoolName of the agentDhcpServerPoolConfigTable." ::= { agentDhcpServerPoolAllocationEntry 1 } agentDhcpServerDynamicPoolIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of the DHCP Address pool. The IP address must be set before setting the IP Mask or IP Prefix Length. After setting IP address, network -mask, or IP Prefix length must be set in order to change the pool type to dynamic. This value shows 0.0.0.0, if the binding type is 'un-allocated',or,'manual'." ::= { agentDhcpServerPoolAllocationEntry 2 } agentDhcpServerDynamicPoolIpMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The bit-combination that renders which portion of the address of the DHCP address pool refers to the network or subnet and which part refers to the host.The IP address must have been set before. This value shows 0.0.0.0, if the binding type is 'un-allocated',or,'manual'." ::= { agentDhcpServerPoolAllocationEntry 3 } agentDhcpServerDynamicPoolIpPrefixLength OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies the no. of bits that comprise the address-prefix. The prefix is an alternative way of specifying the network-mask of the client.The IP address must have been set before. This value shows 0, if the binding type is 'un-allocated',or,'mnaual'." ::= { agentDhcpServerPoolAllocationEntry 4 } agentDhcpServerPoolAllocationType OBJECT-TYPE SYNTAX INTEGER{ un-allocated(0), dynamic(1), manual(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This specifies the type of the binding that is associated with this pool." ::= { agentDhcpServerPoolAllocationEntry 5 } agentDhcpServerManualPoolClientIdentifier OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "It specifies the unique identifier (in colon separated hexadecimal format) of a DHCP client. It is valid for manual bindings only. It displays 'unconfigured',if the binding type is 'un-allocated',or,'dynamic'. To set this object, input should be 7 octets long with the hardware type in the first octet." ::= { agentDhcpServerPoolAllocationEntry 6 } agentDhcpServerManualPoolClientName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..30)) MAX-ACCESS read-write STATUS current DESCRIPTION "It specifies the name of a DHCP client. Client name should't include domain-name. It displays 'unconfigured',if the binding type is 'un-allocated',or,'dynamic'. " ::= { agentDhcpServerPoolAllocationEntry 7 } agentDhcpServerManualPoolClientHWAddr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "It specifies the hardware-address of a DHCP client. It is valid for manual bindings only. It displays 'unconfigured',if the binding type is 'un-allocated',or,'dynamic'. After hardware-address, hardware-type will be configured." ::= { agentDhcpServerPoolAllocationEntry 8 } agentDhcpServerManualPoolClientHWType OBJECT-TYPE SYNTAX INTEGER{ ethernet(1), ieee802(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "It specifies the hardware-type of a DHCP client. It is valid for manual bindings only. It displays 'unconfigured',if the binding type is 'un-allocated',or,'dynamic'. Before this, hardware-address must be configured." DEFVAL { ethernet } ::= { agentDhcpServerPoolAllocationEntry 9 } agentDhcpServerManualPoolIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of the DHCP Address pool for manual binding. The IP address must be set before setting the IP Mask or IP Prefix Length.After setting IP address, network -mask, or IP Prefix length must be set in order to change the pool type to dynamic. This value shows 0.0.0.0, if the binding type is 'un-allocated',or,'dynamic'." ::= { agentDhcpServerPoolAllocationEntry 10 } agentDhcpServerManualPoolIpMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The bit-combination that renders which portion of the address of the DHCP address pool for a manual binding refers to the network or subnet and which part refers to the host. The IP address must have been set before. This value shows 0.0.0.0, if the binding type is 'un-allocated',or,'dynamic'." ::= { agentDhcpServerPoolAllocationEntry 11 } agentDhcpServerManualPoolIpPrefixLength OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies the no. of bits that comprise the address-prefix. The prefix is an alternative way of specifying the network-mask of the client.The IP address must have been set before. This value shows 0, if the binding type is 'un-allocated',or,'dynamic'." ::= { agentDhcpServerPoolAllocationEntry 12 } --*********************************************************************************************** agentDhcpServerExcludedAddressRangeCreate OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "It sets the IP address-ranges(from low to high) that a DHCP server should not assign to DHCP clients. Each time this MIB object is set successfully, one excluded range of IP address will be set. It is given in format - start and end IP address separated by '-' and terminated by ';'. One example would be - 192.168.36.1-200.1.1.1; . This sets one excluded range of IP address,which starts at 192.168.36.1 and ends at 200.1.1.1. If only start IP address is given, end IP address is assumed to be equal to the start IP address. Get operation on this MIB object returns a null-value, as for the purpose of viewing the exclude-address ranges, the user should perform the traversal of agentDhcpServerExcludedAddressRangeTable. For this reason the get operation on object agentDhcpServerExcludedAddressRangeCreate becomes insignificant." ::= { agentDhcpServerPoolConfigGroup 4 } agentDhcpServerExcludedAddressRangeTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentDhcpServerExcludedAddressRangeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the DHCP Server Pool configuration entries." ::= { agentDhcpServerPoolConfigGroup 5 } agentDhcpServerExcludedAddressRangeEntry OBJECT-TYPE SYNTAX AgentDhcpServerExcludedAddressRangeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents entry for a Dhcp server excluded address range table." INDEX { agentDhcpServerExcludedRangeIndex } ::= { agentDhcpServerExcludedAddressRangeTable 1 } -- All objects are of type read-only, except agentDhcpServerExcludedAddressRangeStatus, -- which is of type read-write AgentDhcpServerExcludedAddressRangeEntry ::= SEQUENCE { agentDhcpServerExcludedRangeIndex Unsigned32, agentDhcpServerExcludedStartIpAddress IpAddress, agentDhcpServerExcludedEndIpAddress IpAddress, agentDhcpServerExcludedAddressRangeStatus RowStatus } agentDhcpServerExcludedRangeIndex OBJECT-TYPE SYNTAX Unsigned32 (1..256) MAX-ACCESS read-only STATUS current DESCRIPTION "This specifies the index of the excluded IP address-range table." ::= { agentDhcpServerExcludedAddressRangeEntry 1 } agentDhcpServerExcludedStartIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This specifies the starting IP address of the excluded address-range." ::= { agentDhcpServerExcludedAddressRangeEntry 2 } agentDhcpServerExcludedEndIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This specifies the ending IP address of the excluded address-range." ::= { agentDhcpServerExcludedAddressRangeEntry 3 } agentDhcpServerExcludedAddressRangeStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies the row-status of the excluded address-range. Implemented values are - active(1) and destroy(6). For a valid range, the row-satus will return active(1). When it is set to destroy(6), the corresponding address-range is deleted." ::= { agentDhcpServerExcludedAddressRangeEntry 4 } --*********************************************************************************************** agentDhcpServerPoolOptionCreate OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "This sets the option for an existing DHCP Server pool. Here, it is required to enter the pool-index, for which option is to be set and the value of the DHCP option code in string-format : pool-index and option code separated by '-' and terminated by ';', one example would be -> 1-19; , 1 is the pool-index and 19 is the option code. " ::= { agentDhcpServerPoolConfigGroup 6 } agentDhcpServerPoolOptionTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentDhcpServerPoolOptionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table for configuring DHCP Server options." ::= { agentDhcpServerPoolConfigGroup 7 } agentDhcpServerPoolOptionEntry OBJECT-TYPE SYNTAX AgentDhcpServerPoolOptionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents entry for a Dhcp server option table." INDEX { agentDhcpServerPoolOptionIndex, agentDhcpServerPoolOptionCode } ::= { agentDhcpServerPoolOptionTable 1 } -- All objects are of type read-write, except the indexes agentDhcpServerPoolOptionIndex and -- agentDhcpServerPoolOptionCode -- For a particular poolOption entry, option data ( ASCII, HEX and IP Address) can be -- entered multiple times provided data-format is same each time. AgentDhcpServerPoolOptionEntry ::= SEQUENCE { agentDhcpServerPoolOptionIndex Unsigned32, agentDhcpServerPoolOptionCode Unsigned32, agentDhcpServerOptionPoolName DisplayString, agentDhcpServerPoolOptionAsciiData DisplayString, agentDhcpServerPoolOptionHexData OCTET STRING, agentDhcpServerPoolOptionIpAddressData DisplayString, agentDhcpServerPoolOptionStatus RowStatus } agentDhcpServerPoolOptionIndex OBJECT-TYPE SYNTAX Unsigned32 (1..512) MAX-ACCESS read-only STATUS current DESCRIPTION "The Pool Index alongwith option-code, acts as index for the DHCP Server Option table. " ::= { agentDhcpServerPoolOptionEntry 1 } agentDhcpServerPoolOptionCode OBJECT-TYPE SYNTAX Unsigned32 (1..254) MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies the DHCP option code. This alongwith pool-index acts as the index of the DHCP Server Option table." ::= { agentDhcpServerPoolOptionEntry 2 } agentDhcpServerOptionPoolName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..31)) MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the DHCP Address pool. This value cannot be modified" ::= { agentDhcpServerPoolOptionEntry 3 } agentDhcpServerPoolOptionAsciiData OBJECT-TYPE SYNTAX DisplayString (SIZE(1..441)) MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies an NVT ASCII character string. ASCII character strings that contain white space must be delimited by quotation marks. If an ascii optiondata is entered again, it gets concatenated with the previous ascii data." ::= { agentDhcpServerPoolOptionEntry 4 } agentDhcpServerPoolOptionHexData OBJECT-TYPE SYNTAX DisplayString (SIZE(1..1324)) MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies semi-colon separated hexadecimal data. Two hexadecimal digits in hexadecimal character string represents one byte . Hexadecimal strings can be entered in the following formats : 1) continuous hexadecimal digits like -- 0123456789abcdef 2) hexadecimal digits separated by space ' ' -- 01 23 45 67 de 0f 3) Two hexadecimal digits separated by delimeter ':' -- 01:02:a0 de:0f 78:5e 4) Four hexadecimal digits separated by delimeter '.' -- 01ab.c0de.7865 If a Hex optiondata is entered again, it gets concatenated with the previous Hex data." ::= { agentDhcpServerPoolOptionEntry 5 } agentDhcpServerPoolOptionIpAddressData OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies the IP-address list(each IP-address is separated by comma and the list is terminated by semi-colon) for a DHCP client, an example would be 10.10.1.1,192.168.36.1,157.227.44.1;(no spaces in between). If a IP option is entered again, it gets concatenated with the previous IP data. Maximum no. of IP addresses that can be entered at one time is 8. " ::= { agentDhcpServerPoolOptionEntry 6 } agentDhcpServerPoolOptionStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies the row-status of the DHCP Server Pool option." ::= { agentDhcpServerPoolOptionEntry 7 } --************************************************************************************** -- agentDhcpServerLeaseGroup -> contains MIB objects displaying and clearing leases of a DHCP server -- --************************************************************************************** agentDhcpServerLeaseGroup OBJECT IDENTIFIER ::= { agentDHCPServerPrivate 3 } agentDhcpServerLeaseClearAllBindings OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Clears All the DHCP server bindings." DEFVAL { disable } ::= { agentDhcpServerLeaseGroup 1} agentDhcpServerLeaseTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentDhcpServerLeaseEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the DHCP Server's Lease entries." ::= { agentDhcpServerLeaseGroup 2 } agentDhcpServerLeaseEntry OBJECT-TYPE SYNTAX AgentDhcpServerLeaseEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents entry for a Dhcp server's leases." INDEX { agentDhcpServerLeaseIPAddress } ::= { agentDhcpServerLeaseTable 1 } -- All objects are of type read-only AgentDhcpServerLeaseEntry ::= SEQUENCE { agentDhcpServerLeaseIPAddress IpAddress, agentDhcpServerLeaseIPMask IpAddress, agentDhcpServerLeaseHWAddress MacAddress, agentDhcpServerLeaseRemainingTime TimeTicks, agentDhcpServerLeaseType INTEGER, agentDhcpServerLeaseStatus RowStatus } agentDhcpServerLeaseIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This specifies the IP address leased to the client." ::= { agentDhcpServerLeaseEntry 1 } agentDhcpServerLeaseIPMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This specifies the IP mask of the address leased to the client." ::= { agentDhcpServerLeaseEntry 2 } agentDhcpServerLeaseHWAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This specifies the hardware address of the client." ::= { agentDhcpServerLeaseEntry 3 } agentDhcpServerLeaseRemainingTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "This specifies the period for which the lease is valid. It is displayed in days, hours, minutes, and seconds." ::= { agentDhcpServerLeaseEntry 4 } agentDhcpServerLeaseType OBJECT-TYPE SYNTAX INTEGER{ automatic(1), manual(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This specifies the type of address lease as Automatic or Manual." ::= { agentDhcpServerLeaseEntry 5 } agentDhcpServerLeaseStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies the row-status of the address-lease. Implemented values are - active(1) and destroy(6). For a valid range, the row-satus will return active(1). When it is set to destroy(6), the corresponding address-lease is cleared." ::= { agentDhcpServerLeaseEntry 6 } --************************************************************************************** -- agentDhcpServerAddressConflictGroup -> contains MIB objects displaying and clearing -- address conflicts found by a DHCP server, when addresses are offered to the client. -- --************************************************************************************** agentDhcpServerAddressConflictGroup OBJECT IDENTIFIER ::= { agentDHCPServerPrivate 4 } agentDhcpServerClearAllAddressConflicts OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Clears all the address-conflicts found by DHCP server,when set to enable." DEFVAL { disable } ::= { agentDhcpServerAddressConflictGroup 1} agentDhcpServerAddressConflictLogging OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION " It is used to enable, or disables the logging of address-conflicts on a DHCP Server." DEFVAL { enable } ::= { agentDhcpServerAddressConflictGroup 2} agentDhcpServerAddressConflictTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentDhcpServerAddressConflictEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the conflicting-address entries." ::= { agentDhcpServerAddressConflictGroup 3 } agentDhcpServerAddressConflictEntry OBJECT-TYPE SYNTAX AgentDhcpServerAddressConflictEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents a conflicting-address entry." INDEX { agentDhcpServerAddressConflictIP } ::= { agentDhcpServerAddressConflictTable 1 } -- All objects are of type read-only, except agentDhcpServerAddressConflictStatus which is -- of type read-write AgentDhcpServerAddressConflictEntry ::= SEQUENCE { agentDhcpServerAddressConflictIP IpAddress, agentDhcpServerAddressConflictDetectionType INTEGER, agentDhcpServerAddressConflictDetectionTime TimeTicks, agentDhcpServerAddressConflictStatus RowStatus } agentDhcpServerAddressConflictIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This specifies the conflicting IP address assigned to the client by DHCP server." ::= { agentDhcpServerAddressConflictEntry 1 } agentDhcpServerAddressConflictDetectionType OBJECT-TYPE SYNTAX INTEGER{ ping(1), gratuitousArp(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This specifies the address-conflict detection-method." ::= { agentDhcpServerAddressConflictEntry 2 } agentDhcpServerAddressConflictDetectionTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "This specifies the sysUpTime at which the address-conflict was detected." ::= { agentDhcpServerAddressConflictEntry 3 } agentDhcpServerAddressConflictStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies the row-status of the conflicting-address entry. Implemented values are - active(1) and destroy(6). For a valid range, the row-satus will return active(1). When it is set to destroy(6), the corresponding conflicting-address entry is cleared." ::= { agentDhcpServerAddressConflictEntry 4 } END