-- ***************************************************************** -- LLDP-MED-MIB.my: LLDP MED MIB file -- -- Copyright (c) 2009 by cisco Systems, Inc. -- All rights reserved. -- -- ***************************************************************** LLDP-EXT-MED-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Gauge32, Unsigned32, NOTIFICATION-TYPE FROM SNMPv2-SMI TEXTUAL-CONVENTION, TruthValue FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF lldpExtensions, lldpLocPortNum, lldpRemTimeMark, lldpRemLocalPortNum, lldpRemIndex, lldpPortConfigEntry, lldpRemChassisIdSubtype, lldpRemChassisId FROM LLDP-MIB Dscp FROM DIFFSERV-DSCP-TC SnmpAdminString FROM SNMP-FRAMEWORK-MIB; lldpXMedMIB MODULE-IDENTITY LAST-UPDATED "200507280000Z" -- July 28th, 2005 ORGANIZATION "TIA TR41.4 Working Group" CONTACT-INFO " WG-URL: http://www.tiaonline.org/standards/sfg/scope.cfm#TR-41.4 WG-EMail: tr41@tiacomm.org Contact: Chair, TIA TR-41 Postal: Telecommunications Industry Association 2500 Wilson Blvd., Suite 300 Arlington, VA 22201 USA Tel: (703) 907-7700 E-mail: tr41@tiacomm.org" DESCRIPTION "The LLDP Management Information Base extension module for TIA-TR41.4 media endpoint discovery information. In order to assure the uniqueness of the LLDP-MIB, lldpXMedMIB is branched from lldpExtensions using the TIA OUI value as the node. An OUI/'company_id' is a 24 bit globally unique assigned number referenced by various standards. Copyright (C) TIA (2005). This version of this MIB module is published as Section 13.3 of ANSI/TIA-1057. See the standard itself for full legal notices." REVISION "200507280000Z" -- July 28th, 2005 DESCRIPTION "Published as part of ANSI/TIA-1057." -- OUI for TIA is 4795 (00-12-BB) ::= { lldpExtensions 4795 } ------------------------------------------------------------------------------ ------------------------------------------------------------------------------ -- -- LLDP-MED Information -- ------------------------------------------------------------------------------ ------------------------------------------------------------------------------ lldpXMedNotifications OBJECT IDENTIFIER ::= { lldpXMedMIB 0 } lldpXMedObjects OBJECT IDENTIFIER ::= { lldpXMedMIB 1 } -- LLDP MED Extension Notifications -- Transmission of LLDP MED Extension Notification is controlled by the -- lldpNotificationInterval object in the LLDP MIB defined in -- IEEE 802.1AB-2005 lldpXMedTopologyChangeDetected NOTIFICATION-TYPE OBJECTS { lldpRemChassisIdSubtype, lldpRemChassisId, lldpXMedRemDeviceClass } STATUS current DESCRIPTION "A notification generated by the local device sensing a change in the topology that indicates that a new remote device attached to a local port, or a remote device disconnected or moved from one port to another." ::= { lldpXMedNotifications 1 } -- LLDP MED extension MIB groups lldpXMedConfig OBJECT IDENTIFIER ::= { lldpXMedObjects 1 } lldpXMedLocalData OBJECT IDENTIFIER ::= { lldpXMedObjects 2 } lldpXMedRemoteData OBJECT IDENTIFIER ::= { lldpXMedObjects 3 } -- textual conventions LldpXMedDeviceClass ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Device Class to which the device is a member. A value of notDefined(0) indicates that the device has capabilities not covered by any of the LLDP-MED classes. A value of endpointClass1(1) indicates that the device has endpoint class 1 capabilities. A value of endpointClass2(2) indicates that the device has endpoint class 2 capabilities. A value of endpointClass3(3) indicates that the device has endpoint class 3 capabilities. A value of networkConnectivity(4) indicates that the device has network connectivity device capabilities. " SYNTAX INTEGER { notDefined(0), endpointClass1(1), endpointClass2(2), endpointClass3(3), networkConnectivity(4) } -- LLDP-MED Capabilities TC LldpXMedCapabilities ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Bitmap that includes the MED organizationally defined set of LLDP TLVs the device is capable of and whose transmission is allowed on the local LLDP agent by network management. Each bit in the bitmap corresponds to an LLDP-MED subtype associated with a specific TIA TR41.4 MED TLV. Having the bit 'capabilities(0)' set indicates that the LLDP agent refers to the Capabilities TLVs. Having the bit 'networkPolicy(1)' set indicates that the LLDP agent refers to the Network Policy TLVs. Having the bit 'location(2)' set indicates that the LLDP agent refers to the Emergency Communications System Location TLVs. Having the bit 'extendedPSE(3)' set indicates that the LLDP agent refers to the Extended PoE TLVs with PSE capabilities. Having the bit 'extendedPD(4)' set indicates that the LLDP agent refers to the Extended PoE TLVs with PD capabilities. Having the bit 'inventory(5)' set indicates that the LLDP agent refers to the Hardware Revision, Firmware Revision, Software Revision, Serial Number, Manufacturer Name, Model Name, and Asset ID TLVs." SYNTAX BITS { capabilities(0), networkPolicy(1), location(2), extendedPSE(3), extendedPD(4), inventory(5) } -- Location Subtype Textual Convention LocationSubtype ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The location subtype advertised by the remote endpoint. A value coordinateBased(2) indicates that the location subtype advertised by the endpoint is defined to use the relevant sub- fields of the DHCP option for Coordinate LCI as specified in ANSI/TIA-1057, Section 10.2.4.3.1. A value civicAddress(3) indicates that the location subtype advertised by the endpoint is defined to use the relevant sub- fields of the DHCP option for Civic Address as specified in ANSI/TIA-1057, Section 10.2.4.3.2. A value elin(4) indicates that the location subtype advertised by the endpoint is defined to use the Emergency Location Information Number (ELIN) as specified in ANSI/TIA-1057, Section 10.2.4.3.3." SYNTAX INTEGER { unknown(1), coordinateBased(2), civicAddress(3), elin(4) } -- Policy Application Type Textual Convention PolicyAppType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The media type that defines the primary function of the application for the policy advertised by an endpoint. Having the bit voice(1) set indicates that the media type defining a primary function of the application for the policy advertised on the local port is voice. Having the bit voiceSignaling(3) set indicates that the media type defining a primary function of the application for the policy advertised on the local port is voice signaling. Having the bit guestVoice(4) set indicates that the media type Defining a primary function of the application for the policy advertised on the local port is guest voice. Having the bit guestVoiceSignaling(5) set indicates that the media type defining a primary function of the application for the policy advertised on the local port is guest voice signaling. Having the bit softPhoneVoice(6) set indicates that the media type Defining a primary function of the application for the policy advertised on the local port is softphone voice. Having the bit videoConferencing(7) set indicates that the media type defining a primary function of the application for the policy advertised on the local port is voice. Having the bit streamingVideo(8) set indicates that the media type defining a primary function of the application for the policy advertised on the local port is streaming video. Having the bit videoSignaling(2) set indicates that the media type defining a primary function of the application for the policy advertised on the local port is video signaling." SYNTAX BITS { unknown(0), voice(1), voiceSignaling(2), guestVoice(3), guestVoiceSignaling(4), softPhoneVoice(5), videoconferencing(6), streamingVideo(7), videoSignaling(8) } ------------------------------------------------------------------------------ -- MED - Configuration ------------------------------------------------------------------------------ lldpXMedLocDeviceClass OBJECT-TYPE SYNTAX LldpXMedDeviceClass MAX-ACCESS read-only STATUS current DESCRIPTION "Local Device Class." REFERENCE " ANSI/TIA-1057, Section 10.2.2.2" ::= { lldpXMedConfig 1 } lldpXMedPortConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXMedPortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that controls selection of LLDP TLVs to be transmitted on individual ports." ::= { lldpXMedConfig 2 } lldpXMedPortConfigEntry OBJECT-TYPE SYNTAX LldpXMedPortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "LLDP configuration information that controls the transmission of the MED organizationally defined TLVs on LLDP transmission capable ports. This configuration object augments the lldpPortConfigEntry of the LLDP-MIB, therefore it is only present along with the port configuration defined by the associated lldpPortConfigEntry entry. Each active lldpXMedPortConfigEntry must be stored and retrieved from non-volatile storage (along with the corresponding lldpPortConfigEntry) after a re-initialization of the management system." AUGMENTS { lldpPortConfigEntry } ::= { lldpXMedPortConfigTable 1 } LldpXMedPortConfigEntry ::= SEQUENCE { lldpXMedPortCapSupported LldpXMedCapabilities, lldpXMedPortConfigTLVsTxEnable LldpXMedCapabilities, lldpXMedPortConfigNotifEnable TruthValue } lldpXMedPortCapSupported OBJECT-TYPE SYNTAX LldpXMedCapabilities MAX-ACCESS read-only STATUS current DESCRIPTION "The bitmap includes the MED organizationally defined set of LLDP TLVs whose transmission is possible for the respective port on the LLDP agent of the device. Each bit in the bitmap corresponds to an LLDP-MED subtype associated with a specific TIA TR41.4 MED optional TLV. If the bit is set, the agent supports the corresponding TLV." REFERENCE "ANSI/TIA-1057, Section 10.2.2.3" ::= { lldpXMedPortConfigEntry 1 } lldpXMedPortConfigTLVsTxEnable OBJECT-TYPE SYNTAX LldpXMedCapabilities MAX-ACCESS read-write STATUS current DESCRIPTION "The lldpXMedPortConfigTLVsTxEnable, defined as a bitmap, includes the MED organizationally defined set of LLDP TLVs whose transmission is allowed on the local LLDP agent by the network management. Each bit in the bitmap corresponds to an LLDP-MED subtype associated with a specific TIA TR41.4 MED optional TLV. If the bit is set, the agent will send the corresponding TLV if the respective capability is supported per port. Setting a bit with in this object for a non-supported capability shall have no functional effect and will result in an inconsistent value error returned to the management application. There are other rules and restrictions that prevent arbitrary combinations of TLVs to be enabled on LLDP-MED devices according to the device classes. These rules are defined in Section 10.2.1, Tables 5 - 9 of ANSI/TIA-1057. In case a management application attempts to set this object to a value that does not follow the rules, the set operation shall have and will result in an inconsistent value error returned to the management application. Setting this object to an empty set is valid and effectively disables LLDP-MED on a per-port basis by disabling transmission of all MED organizational TLVs. In this case the remote tables objects in the LLDP-MED MIB corresponding to the respective port will not be populated. The default value for lldpXMedPortConfigTLVsTxEnable object is an empty set, which means no enumerated values are set. The value of this object must be restored from non-volatile storage after a re-initialization of the management system." REFERENCE "ANSI/TIA-1057, Section 10.2.2.3" DEFVAL { { } } ::= { lldpXMedPortConfigEntry 2 } lldpXMedPortConfigNotifEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A value of 'true(1)' enables sending the topology change traps on this port. A value of 'false(2)' disables sending the topology change traps on this port." REFERENCE " ANSI/TIA-1057, Section 12.3" DEFVAL { false } ::= { lldpXMedPortConfigEntry 3 } lldpXMedFastStartRepeatCount OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of times the fast start LLDPDU are being sent during the activation of the fast start mechanism defined by LLDP-MED." REFERENCE " ANSI/TIA-1057, Section 11.2.1" DEFVAL { 3 } ::= { lldpXMedConfig 3 } ------------------------------------------------------------------------------ -- LLDP-MED - Local Device Information ------------------------------------------------------------------------------ --- --- lldpXMedLocMediaPolicyTable: Local Media Policy --- Information Table --- --- lldpXMedLocMediaPolicyTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXMedLocMediaPolicyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one row per policy type per port of media policy information (as a part of the MED organizational extension) on the local system known to this agent." ::= { lldpXMedLocalData 1 } lldpXMedLocMediaPolicyEntry OBJECT-TYPE SYNTAX LldpXMedLocMediaPolicyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular policy on a specific port component." INDEX { lldpLocPortNum, lldpXMedLocMediaPolicyAppType } ::= { lldpXMedLocMediaPolicyTable 1 } LldpXMedLocMediaPolicyEntry ::= SEQUENCE { lldpXMedLocMediaPolicyAppType PolicyAppType, lldpXMedLocMediaPolicyVlanID Integer32, lldpXMedLocMediaPolicyPriority Integer32, lldpXMedLocMediaPolicyDscp Dscp, lldpXMedLocMediaPolicyUnknown TruthValue, lldpXMedLocMediaPolicyTagged TruthValue } lldpXMedLocMediaPolicyAppType OBJECT-TYPE SYNTAX PolicyAppType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The media type that defines the primary function of the application for the policy advertised by an endpoint." REFERENCE "ANSI/TIA-1057, Section 10.2.3.1" ::= { lldpXMedLocMediaPolicyEntry 1 } lldpXMedLocMediaPolicyVlanID OBJECT-TYPE SYNTAX Integer32 (0|1..4094|4095) MAX-ACCESS read-only STATUS current DESCRIPTION "An extension of the VLAN Identifier for the port, as defined in IEEE 802.1P-1998. A value of 1 through 4094 is used to define a valid PVID. A value of 0 shall be used if the device is using priority tagged frames, meaning that only the 802.1p priority level is significant and the default VID of the ingress port is being used instead. A value of 4095 is reserved for implementation use." REFERENCE " ANSI/TIA-1057, Section 10.2.3.5" ::= { lldpXMedLocMediaPolicyEntry 2 } lldpXMedLocMediaPolicyPriority OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the value of the 802.1p priority which is associated with the given port on the local system." REFERENCE " ANSI/TIA-1057, Section 10.2.3.6 " ::= { lldpXMedLocMediaPolicyEntry 3 } lldpXMedLocMediaPolicyDscp OBJECT-TYPE SYNTAX Dscp MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the value of the Differentiated Service Code Point (DSCP) as defined in IETF RFC 2474 and RFC 2475 which is associated with the given port on the local system." REFERENCE " ANSI/TIA-1057, Section 10.2.3.7" ::= { lldpXMedLocMediaPolicyEntry 4 } lldpXMedLocMediaPolicyUnknown OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A value of 'true' indicates that the network policy for the specified application type is currently unknown. In this case, the VLAN ID, the layer 2 priority and the DSCP value fields are ignored. A value of 'false' indicates that this network policy is defined " REFERENCE " ANSI/TIA-1057, Section 10.2.3.2" ::= { lldpXMedLocMediaPolicyEntry 5 } lldpXMedLocMediaPolicyTagged OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A value of 'true' indicates that the application is using a tagged VLAN. A value of 'false' indicates that for the specific application the device either is using an untagged VLAN or does not support port based VLAN operation. In this case, both the VLAN ID and the Layer 2 priority fields are ignored and only the DSCP value has relevance " REFERENCE " ANSI/TIA-1057, Section 10.2.3.3" ::= { lldpXMedLocMediaPolicyEntry 6 } --- Inventory Information --- Local Inventory Information transmitted by an endpoint lldpXMedLocHardwareRev OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor-specific hardware revision string as advertised by the endpoint." REFERENCE " ANSI/TIA-1057, Section 10.2.6.1" ::= { lldpXMedLocalData 2 } lldpXMedLocFirmwareRev OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor-specific firmware revision string as advertised by the endpoint." REFERENCE " ANSI/TIA-1057, Section 10.2.6.2" ::= { lldpXMedLocalData 3 } lldpXMedLocSoftwareRev OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor-specific software revision string as advertised by the endpoint." REFERENCE " ANSI/TIA-1057, Section 10.2.6.3" ::= { lldpXMedLocalData 4 } lldpXMedLocSerialNum OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor-specific serial number as advertised by the endpoint." REFERENCE " ANSI/TIA-1057, Section 10.2.6.4" ::= { lldpXMedLocalData 5 } lldpXMedLocMfgName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor-specific manufacturer name as advertised by the endpoint." REFERENCE " ANSI/TIA-1057, Section 10.2.6.5" ::= { lldpXMedLocalData 6 } lldpXMedLocModelName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor-specific model name as advertised by the endpoint." REFERENCE " ANSI/TIA-1057, Section 10.2.6.6" ::= { lldpXMedLocalData 7 } lldpXMedLocAssetID OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor-specific asset tracking identifier as advertised by the endpoint." REFERENCE " ANSI/TIA-1057, Section 10.2.6.7" ::= { lldpXMedLocalData 8 } --- Location Information --- Local Location Information transmitted by an endpoint --- lldpXMedLocLocationTable - Location Information --- lldpXMedLocLocationTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXMedLocLocationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains Location information as advertised by the local system. The information may be configured per port by a Location Information Server (LIS) or other management application. Multiple Location TLVs of different subtypes may be transmitted in the same PDU. The information in this table MUST be stored in non-volatile-memory and persist over restart/reboot sequences." ::= { lldpXMedLocalData 9 } lldpXMedLocLocationEntry OBJECT-TYPE SYNTAX LldpXMedLocLocationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about Location information for the local device." INDEX { lldpLocPortNum, lldpXMedLocLocationSubtype} ::= { lldpXMedLocLocationTable 1 } LldpXMedLocLocationEntry ::= SEQUENCE { lldpXMedLocLocationSubtype LocationSubtype, lldpXMedLocLocationInfo OCTET STRING } lldpXMedLocLocationSubtype OBJECT-TYPE SYNTAX LocationSubtype MAX-ACCESS not-accessible STATUS current DESCRIPTION "The location subtype advertised by the local device." REFERENCE "ANSI/TIA-1057, Section 10.2.4.2" ::= { lldpXMedLocLocationEntry 1 } lldpXMedLocLocationInfo OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..256)) MAX-ACCESS read-write STATUS current DESCRIPTION "The location information. Parsing of this information is dependent upon the location subtype, as defined by the value of the lldpXMedLocLocationSubtype object. " REFERENCE "ANSI/TIA-1057, Section 10.2.4.3" DEFVAL { "" } ::= { lldpXMedLocLocationEntry 2 } --- Extended Power over Ethernet objects --- lldpXMedLocXPoEDeviceType OBJECT-TYPE SYNTAX INTEGER { unknown(1), pseDevice(2), pdDevice(3), none(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Defines the type of Power-via-MDI (Power over Ethernet) advertised by the local device. A value pseDevice(2) indicates that the device is advertised as a Power Sourcing Entity (PSE). A value pdDevice(3) indicates that the device is advertised as a Powered Device (PD). A value of none(4) indicates that the device does not support PoE." REFERENCE "ANSI/TIA-1057, Section 10.2.5.1" ::= { lldpXMedLocalData 10 } --- Extended PoE - PSE objects --- PSE Port Table lldpXMedLocXPoEPSEPortTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXMedLocXPoEPSEPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one row per port of PSE PoE information on the local system known to this agent." ::= { lldpXMedLocalData 11 } lldpXMedLocXPoEPSEPortEntry OBJECT-TYPE SYNTAX LldpXMedLocXPoEPSEPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular port PoE information." INDEX { lldpLocPortNum } ::= { lldpXMedLocXPoEPSEPortTable 1 } LldpXMedLocXPoEPSEPortEntry ::= SEQUENCE { lldpXMedLocXPoEPSEPortPowerAv Gauge32, lldpXMedLocXPoEPSEPortPDPriority INTEGER } lldpXMedLocXPoEPSEPortPowerAv OBJECT-TYPE SYNTAX Gauge32 (0..1023) UNITS "tenth of watt" MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the value of the power available from the PSE via this port expressed in units of 0.1 watts." REFERENCE " ANSI/TIA-1057, Section 10.2.5.4 " ::= { lldpXMedLocXPoEPSEPortEntry 1 } lldpXMedLocXPoEPSEPortPDPriority OBJECT-TYPE SYNTAX INTEGER { unknown(1), critical(2), high(3), low(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Reflects the PD power priority that is being advertised on this PSE port. If both locally configure priority and ldpXMedRemXPoEPDPowerPriority are available on this port, it is a matter of local policy which one takes precedence. This object reflects the active value on this port. If the priority is not configured or known by the PD, the value unknown(1) will be returned. A value critical(2) indicates that the device advertises its power Priority as critical, as per RFC 3621. A value high(3) indicates that the device advertises its power Priority as high, as per RFC 3621. A value low(4) indicates that the device advertises its power Priority as low, as per RFC 3621." REFERENCE "ANSI/TIA-1057, Section 10.2.5.3" ::= { lldpXMedLocXPoEPSEPortEntry 2 } lldpXMedLocXPoEPSEPowerSource OBJECT-TYPE SYNTAX INTEGER { unknown(1), primary(2), backup(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Defines the type of PSE Power Source advertised by the local device. A value primary(2) indicates that the device advertises its power source as primary. A value backup(3) indicates that the device advertises its power Source as backup." REFERENCE "ANSI/TIA-1057, Section 10.2.5.2" ::= { lldpXMedLocalData 12 } --- Extended PoE - PD objects lldpXMedLocXPoEPDPowerReq OBJECT-TYPE SYNTAX Gauge32 (0..1023) UNITS "tenth of watt" MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the value of the power required by a PD expressed in units of 0.1 watts." REFERENCE " ANSI/TIA-1057, Section 10.2.4.3 " ::= { lldpXMedLocalData 13 } lldpXMedLocXPoEPDPowerSource OBJECT-TYPE SYNTAX INTEGER { unknown(1), fromPSE(2), local(3), localAndPSE(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Defines the type of Power Source advertised as being used by the local device. A value fromPSE(2) indicates that the device advertises its power source as received from a PSE. A value local(3) indicates that the device advertises its power source as local. A value localAndPSE(4) indicates that the device advertises its power source as using both local and PSE power." REFERENCE "ANSI/TIA-1057, Section 10.2.5.2" ::= { lldpXMedLocalData 14 } lldpXMedLocXPoEPDPowerPriority OBJECT-TYPE SYNTAX INTEGER { unknown(1), critical(2), high(3), low(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Defines the priority advertised as being required by this PD. A value critical(2) indicates that the device advertises its power Priority as critical, as per RFC 3621. A value high(3) indicates that the device advertises its power Priority as high, as per RFC 3621. A value low(4) indicates that the device advertises its power Priority as low, as per RFC 3621." REFERENCE "ANSI/TIA-1057, Section 10.2.5.3" ::= { lldpXMedLocalData 15 } ------------------------------------------------------------------------------ -- LLDP-MED - Remote Devices Information ------------------------------------------------------------------------------ -- LLdpXMedRemCapabilitiesTable -- this table is read by a manager to determine what capabilities -- exists and are enabled on the remote system connected to the port -- The information in this table is based upon the information advertised -- by the remote device and received on each port in the capabilities TLV lldpXMedRemCapabilitiesTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXMedRemCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that displays LLDP-MED capabilities of remote devices connected to individual ports." ::= { lldpXMedRemoteData 1 } lldpXMedRemCapabilitiesEntry OBJECT-TYPE SYNTAX LldpXMedRemCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "LLDP-MED capabilities of remote devices connected to the device ports and communicating via LLDP-MED. The remote tables in the LLDP-MED MIB excepting this table may be sparsely populate. An entry in one of these table is meaningful and shall be populated by the agent only if the corresponding bits for the respective function are set in the objects in this table. " INDEX { lldpRemTimeMark, lldpRemLocalPortNum, lldpRemIndex } ::= { lldpXMedRemCapabilitiesTable 1 } LldpXMedRemCapabilitiesEntry ::= SEQUENCE { lldpXMedRemCapSupported LldpXMedCapabilities, lldpXMedRemCapCurrent LldpXMedCapabilities, lldpXMedRemDeviceClass LldpXMedDeviceClass } lldpXMedRemCapSupported OBJECT-TYPE SYNTAX LldpXMedCapabilities MAX-ACCESS read-only STATUS current DESCRIPTION "The bitmap includes the MED organizationally defined set of LLDP TLVs whose transmission is possible on the LLDP agent of the remote device connected to this port. Each bit in the bitmap corresponds to an LLDP-MED subtype associated with a specific TIA TR41.4 MED optional TLV. If the bit is set, the agent has the capability to support the corresponding TLV." REFERENCE "ANSI/TIA-1057, Sections 10.2.2.1" ::= { lldpXMedRemCapabilitiesEntry 1 } lldpXMedRemCapCurrent OBJECT-TYPE SYNTAX LldpXMedCapabilities MAX-ACCESS read-only STATUS current DESCRIPTION "The bitmap includes the MED organizationally defined set of LLDP TLVs whose transmission is possible on the LLDP agent of the remote device connected to this port. Each bit in the bitmap corresponds to an LLDP-MED subtype associated with a specific TIA TR41.4 MED optional TLV. If the bit is set, the agent currently supports the corresponding TLV." REFERENCE "ANSI/TIA-1057, Sections 10.2.2.1" ::= { lldpXMedRemCapabilitiesEntry 2 } lldpXMedRemDeviceClass OBJECT-TYPE SYNTAX LldpXMedDeviceClass MAX-ACCESS read-only STATUS current DESCRIPTION "Device Class as advertised by the device remotely connected to the port." REFERENCE " ANSI/TIA-1057, Section 10.2.2.2" ::= { lldpXMedRemCapabilitiesEntry 3 } --- --- --- lldpXMedRemMediaPolicyTable: Media Policy Table --- --- lldpXMedRemMediaPolicyTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXMedRemMediaPolicyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains media policy information as advertised by the remote system. This table may be sparsely populated. Entries in this table are relevant only if the networkPolicy(0) bits in the lldpXMedRemCapSupported and lldpXMedRemCapCurrent objects of the corresponding ports are set." ::= { lldpXMedRemoteData 2 } lldpXMedRemMediaPolicyEntry OBJECT-TYPE SYNTAX LldpXMedRemMediaPolicyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about the per port per policy type policy information for a particular physical network connection." INDEX { lldpRemTimeMark, lldpRemLocalPortNum, lldpRemIndex, lldpXMedRemMediaPolicyAppType } ::= { lldpXMedRemMediaPolicyTable 1 } LldpXMedRemMediaPolicyEntry ::= SEQUENCE { lldpXMedRemMediaPolicyAppType PolicyAppType, lldpXMedRemMediaPolicyVlanID Integer32, lldpXMedRemMediaPolicyPriority Integer32, lldpXMedRemMediaPolicyDscp Dscp, lldpXMedRemMediaPolicyUnknown TruthValue, lldpXMedRemMediaPolicyTagged TruthValue } lldpXMedRemMediaPolicyAppType OBJECT-TYPE SYNTAX PolicyAppType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The media type that defines the primary function of the application for the policy advertised by the endpoint connected remotely to this port." REFERENCE "ANSI/TIA-1057, Section 10.2.3.1" ::= { lldpXMedRemMediaPolicyEntry 1 } lldpXMedRemMediaPolicyVlanID OBJECT-TYPE SYNTAX Integer32 (0|1..4094|4095) MAX-ACCESS read-only STATUS current DESCRIPTION "An extension of the VLAN Identifier for the remote system connected to this port, as defined in IEEE 802.1P-1998. A value of 1 through 4094 is used to define a valid PVID. A value of 0 shall be used if the device is using priority tagged frames, meaning that only the 802.1p priority level is significant and the default VID of the ingress port is being used instead. A value of 4095 is reserved for implementation use." REFERENCE " ANSI/TIA-1057, Section 10.2.3.5" ::= { lldpXMedRemMediaPolicyEntry 2 } lldpXMedRemMediaPolicyPriority OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the value of the 802.1p priority which is associated with the remote system connected at given port." REFERENCE " ANSI/TIA-1057, Section 10.2.3.6" ::= { lldpXMedRemMediaPolicyEntry 3 } lldpXMedRemMediaPolicyDscp OBJECT-TYPE SYNTAX Dscp MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the value of the Differentiated Service Code Point (DSCP) as defined in IETF RFC 2474 and RFC 2475 which is associated with remote system connected at the port." REFERENCE " ANSI/TIA-1057, Section 10.2.3.7" ::= { lldpXMedRemMediaPolicyEntry 4 } lldpXMedRemMediaPolicyUnknown OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A value of 'true' indicates that the network policy for the specified application type is currently unknown. In this case, the VLAN ID, the layer 2 priority and the DSCP value fields are ignored. A value of 'false' indicates that this network policy is defined." REFERENCE " ANSI/TIA-1057, Section 10.2.3.2" ::= { lldpXMedRemMediaPolicyEntry 5 } lldpXMedRemMediaPolicyTagged OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A value of 'true' indicates that the application is using a tagged VLAN. A value of 'false' indicates that for the specific application the device either is using an untagged VLAN or does not support port based VLAN operation. In this case, both the VLAN ID and the Layer 2 priority fields are ignored and only the DSCP value has relevance " REFERENCE " ANSI/TIA-1057, Section 10.2.3.3" ::= { lldpXMedRemMediaPolicyEntry 6 } --- lldpXMedRemInventoryTable - Remote Inventory Information --- lldpXMedRemInventoryTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXMedRemInventoryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains inventory information as advertised by the remote system. This table may be sparsely populated. Entries in this table are relevant only if the inventory(2) bits in the lldpXMedRemCapSupported and lldpXMedRemCapCurrent objects of the corresponding ports are set " ::= { lldpXMedRemoteData 3 } lldpXMedRemInventoryEntry OBJECT-TYPE SYNTAX LldpXMedRemInventoryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about inventory information for the remote devices connected to the ports." INDEX { lldpRemTimeMark, lldpRemLocalPortNum, lldpRemIndex } ::= { lldpXMedRemInventoryTable 1 } LldpXMedRemInventoryEntry ::= SEQUENCE { lldpXMedRemHardwareRev SnmpAdminString, lldpXMedRemFirmwareRev SnmpAdminString, lldpXMedRemSoftwareRev SnmpAdminString, lldpXMedRemSerialNum SnmpAdminString, lldpXMedRemMfgName SnmpAdminString, lldpXMedRemModelName SnmpAdminString, lldpXMedRemAssetID SnmpAdminString } lldpXMedRemHardwareRev OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor-specific hardware revision string as advertised by the remote endpoint." REFERENCE " ANSI/TIA-1057, Section 10.2.6.1" ::= { lldpXMedRemInventoryEntry 1 } lldpXMedRemFirmwareRev OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor-specific firmware revision string as advertised by the remote endpoint." REFERENCE " ANSI/TIA-1057, Section 10.2.6.2" ::= { lldpXMedRemInventoryEntry 2 } lldpXMedRemSoftwareRev OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor-specific software revision string as advertised by the remote endpoint." REFERENCE " ANSI/TIA-1057, Section 10.2.6.3" ::= { lldpXMedRemInventoryEntry 3 } lldpXMedRemSerialNum OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor-specific serial number as advertised by the remote endpoint." REFERENCE " ANSI/TIA-1057, Section 10.2.6.4" ::= { lldpXMedRemInventoryEntry 4 } lldpXMedRemMfgName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor-specific manufacturer name as advertised by the remote endpoint." REFERENCE " ANSI/TIA-1057, Section 10.2.6.5" ::= { lldpXMedRemInventoryEntry 5 } lldpXMedRemModelName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor-specific model name as advertised by the remote endpoint." REFERENCE " ANSI/TIA-1057, Section 10.2.6.6" ::= { lldpXMedRemInventoryEntry 6 } lldpXMedRemAssetID OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor-specific asset tracking identifier as advertised by the remote endpoint." REFERENCE " ANSI/TIA-1057, Section 10.2.6.7" ::= { lldpXMedRemInventoryEntry 7 } --- lldpXMedRemLocationTable - Remote Location Information --- lldpXMedRemLocationTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXMedRemLocationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains Location information as advertised by the remote system. This table may be sparsely populated. Entries in this table are relevant only if the Location(3) bits in the lldpXMedRemCapSupported and lldpXMedRemCapCurrent objects of the corresponding ports are set " ::= { lldpXMedRemoteData 4 } lldpXMedRemLocationEntry OBJECT-TYPE SYNTAX LldpXMedRemLocationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about Location information for the remote devices connected to the ports." INDEX { lldpRemTimeMark, lldpRemLocalPortNum, lldpRemIndex, lldpXMedRemLocationSubtype} ::= { lldpXMedRemLocationTable 1 } LldpXMedRemLocationEntry ::= SEQUENCE { lldpXMedRemLocationSubtype LocationSubtype, lldpXMedRemLocationInfo OCTET STRING } lldpXMedRemLocationSubtype OBJECT-TYPE SYNTAX LocationSubtype MAX-ACCESS not-accessible STATUS current DESCRIPTION "The location subtype advertised by the remote endpoint." REFERENCE "ANSI/TIA-1057, Section 10.2.4.2 " ::= { lldpXMedRemLocationEntry 1 } lldpXMedRemLocationInfo OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..256)) MAX-ACCESS read-only STATUS current DESCRIPTION "The location information advertised by the remote endpoint. Parsing of this information is dependent upon the location subtype, as defined by the value of the corresponding lldpXMedRemLocationSubType object. " REFERENCE "ANSI/TIA-1057, Section 10.2.4.3 " ::= { lldpXMedRemLocationEntry 2 } --- lldpXMedRemXPoETable - Information about Remote PoE Device Type --- lldpXMedRemXPoETable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXMedRemXPoEEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information about the PoE device type as advertised by the remote system. This table is densely populated." ::= { lldpXMedRemoteData 5 } lldpXMedRemXPoEEntry OBJECT-TYPE SYNTAX LldpXMedRemXPoEEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about PoE type of the remote devices connected to the ports." INDEX { lldpRemTimeMark, lldpRemLocalPortNum, lldpRemIndex } ::= { lldpXMedRemXPoETable 1 } LldpXMedRemXPoEEntry ::= SEQUENCE { lldpXMedRemXPoEDeviceType INTEGER } lldpXMedRemXPoEDeviceType OBJECT-TYPE SYNTAX INTEGER { unknown(1), pseDevice(2), pdDevice(3), none(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Defines the type of Power-via-MDI (Power over Ethernet) advertised by the remote device. A value pseDevice(2) indicates that the device is advertised as a Power Sourcing Entity (PSE). A value pdDevice(3) indicates that the device is advertised as a Powered Device (PD). A value none(4) indicates that the device does not support PoE." REFERENCE "ANSI/TIA-1057, Section 10.2.5.1" ::= { lldpXMedRemXPoEEntry 1 } --- lldpXMedRemXPoEPDTable - Extended PoE PSE Information from the remote device --- lldpXMedRemXPoEPSETable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXMedRemXPoEPSEEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains extended PoE information as advertised by the remote devices of PSE type. This table may be sparsely populated. Entries in this table are relevant only if the extendedPSE(4) bits in the lldpXMedRemCapSupported and lldpXMedRemCapCurrent objects of the corresponding ports are set " ::= { lldpXMedRemoteData 6 } lldpXMedRemXPoEPSEEntry OBJECT-TYPE SYNTAX LldpXMedRemXPoEPSEEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about Extended PoE PSE information for the remote devices connected to the ports." INDEX { lldpRemTimeMark, lldpRemLocalPortNum, lldpRemIndex } ::= { lldpXMedRemXPoEPSETable 1 } LldpXMedRemXPoEPSEEntry ::= SEQUENCE { lldpXMedRemXPoEPSEPowerAv Gauge32, lldpXMedRemXPoEPSEPowerSource INTEGER, lldpXMedRemXPoEPSEPowerPriority INTEGER } lldpXMedRemXPoEPSEPowerAv OBJECT-TYPE SYNTAX Gauge32 (0..1023) UNITS "tenth of watt" MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the value of the power available from the PSE via this port expressed in units of 0.1 watts on the remote device." REFERENCE " ANSI/TIA-1057, Section 10.2.5.4" ::= { lldpXMedRemXPoEPSEEntry 1 } lldpXMedRemXPoEPSEPowerSource OBJECT-TYPE SYNTAX INTEGER { unknown(1), primary(2), backup(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Defines the type of PSE Power Source advertised by the remote device. A value primary(2) indicates that the device advertises its power source as primary. A value backup(3) indicates that the device advertises its power Source as backup." REFERENCE "ANSI/TIA-1057, Section 10.2.5.2" ::= { lldpXMedRemXPoEPSEEntry 2 } lldpXMedRemXPoEPSEPowerPriority OBJECT-TYPE SYNTAX INTEGER { unknown(1), critical(2), high(3), low(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the value of the PSE power priority advertised by the remote device. A value critical(2) indicates that the device advertises its power priority as critical, as per RFC 3621. A value high(3) indicates that the device advertises its power priority as high, as per RFC 3621. A value low(4) indicates that the device advertises its power priority as low, as per RFC 3621." REFERENCE "ANSI/TIA-1057, Section 10.2.5.3" ::= { lldpXMedRemXPoEPSEEntry 3 } --- lldpXMedRemXPoEPDTable - Extended PoE PD Information from the remote device --- lldpXMedRemXPoEPDTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXMedRemXPoEPDEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains extended PoE information as advertised by the remote devices of PD type. This table may be sparsely populated. Entries in this table are relevant only if the extendedPD(5) bits in the lldpXMedRemCapSupported and lldpXMedRemCapCurrent objects of the corresponding ports are set " ::= { lldpXMedRemoteData 7 } lldpXMedRemXPoEPDEntry OBJECT-TYPE SYNTAX LldpXMedRemXPoEPDEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about XPoEPD information for the remote devices connected to the ports." INDEX { lldpRemTimeMark, lldpRemLocalPortNum, lldpRemIndex } ::= { lldpXMedRemXPoEPDTable 1 } LldpXMedRemXPoEPDEntry ::= SEQUENCE { lldpXMedRemXPoEPDPowerReq Gauge32, lldpXMedRemXPoEPDPowerSource INTEGER, lldpXMedRemXPoEPDPowerPriority INTEGER } lldpXMedRemXPoEPDPowerReq OBJECT-TYPE SYNTAX Gauge32 (0..1023) UNITS "tenth of watt" MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the value of the power required by a PD connected remotely to the port expressed in units of 0.1 watts." REFERENCE " ANSI/TIA-1057, Section 10.2.5.4 " ::= { lldpXMedRemXPoEPDEntry 1 } lldpXMedRemXPoEPDPowerSource OBJECT-TYPE SYNTAX INTEGER { unknown(1), fromPSE(2), local(3), localAndPSE(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Defines the type of Power Source advertised as being used by the device connected remotely to the port. A value fromPSE(2) indicates that the device advertises its power source as received from a PSE. A value local(3) indicates that the device advertises its power source as local. A value localAndPSE(4) indicates that the device advertises its power source as using both local and PSE power." REFERENCE "ANSI/TIA-1057, Section 10.2.5.2" ::= { lldpXMedRemXPoEPDEntry 2 } lldpXMedRemXPoEPDPowerPriority OBJECT-TYPE SYNTAX INTEGER { unknown(1), critical(2), high(3), low(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Defines the priority advertised as being required by the PD connected remotely to the port. A value critical(2) indicates that the device advertises its power Priority as critical, as per RFC 3621. A value high(3) indicates that the device advertises its power Priority as high, as per RFC 3621. A value low(4) indicates that the device advertises its power Priority as low, as per RFC 3621." REFERENCE "ANSI/TIA-1057, Section 10.2.5.3" ::= { lldpXMedRemXPoEPDEntry 3 } --- -- conformance information lldpXMedConformance OBJECT IDENTIFIER ::= { lldpXMedMIB 2 } lldpXMedCompliances OBJECT IDENTIFIER ::= { lldpXMedConformance 1 } lldpXMedGroups OBJECT IDENTIFIER ::= { lldpXMedConformance 2 } -- compliance statements lldpXMedCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities which implement the LLDP MED extension MIB." MODULE -- this module MANDATORY-GROUPS { lldpXMedConfigGroup, lldpXMedRemSysGroup, lldpXMedNotificationsGroup } GROUP lldpXMedOptMediaPolicyGroup DESCRIPTION "This group represents the information associated with the LLDP-MED optional Media Policy TLVs, therefore the agent may not implement them." GROUP lldpXMedOptInventoryGroup DESCRIPTION "This group represents the information associated with the LLDP-MED optional inventory TLVs, therefore the agent may not implement them." GROUP lldpXMedOptLocationGroup DESCRIPTION "This group represents the information associated with the LLDP-MED optional Location TLVs, therefore the agent may not implement them." GROUP lldpXMedOptPoEPSEGroup DESCRIPTION "This group represents the information associated with the LLDP-MED optional extended PoE PolicyTLVs, carrying PSE information, therefore the agent may not implement them." GROUP lldpXMedOptPoEPDGroup DESCRIPTION " This group represents the information associated with the LLDP-MED optional extended PoE Policy TLVs, carrying PD information, therefore the agent may not implement them." ::= { lldpXMedCompliances 1 } -- MIB groupings lldpXMedConfigGroup OBJECT-GROUP OBJECTS { lldpXMedPortCapSupported, lldpXMedPortConfigTLVsTxEnable, lldpXMedPortConfigNotifEnable, lldpXMedFastStartRepeatCount, lldpXMedLocXPoEDeviceType, lldpXMedLocDeviceClass } STATUS current DESCRIPTION "The collection of objects which are used to configure or describe the configuration or behavior of the LLDP-MED organizational extension implementation." ::= { lldpXMedGroups 1 } lldpXMedOptMediaPolicyGroup OBJECT-GROUP OBJECTS { lldpXMedLocMediaPolicyVlanID, lldpXMedLocMediaPolicyPriority, lldpXMedLocMediaPolicyDscp, lldpXMedLocMediaPolicyUnknown, lldpXMedLocMediaPolicyTagged } STATUS current DESCRIPTION "The collection of objects which are used to represent LLDP MED organizational extensions for Media Policy Information." ::= { lldpXMedGroups 2 } lldpXMedOptInventoryGroup OBJECT-GROUP OBJECTS { lldpXMedLocHardwareRev, lldpXMedLocFirmwareRev, lldpXMedLocSoftwareRev, lldpXMedLocSerialNum, lldpXMedLocMfgName, lldpXMedLocModelName, lldpXMedLocAssetID } STATUS current DESCRIPTION "The collection of objects which are used to represent LLDP MED organizational extension for inventory Information." ::= { lldpXMedGroups 3 } lldpXMedOptLocationGroup OBJECT-GROUP OBJECTS { lldpXMedLocLocationInfo } STATUS current DESCRIPTION "The collection of objects which are used to represent LLDP MED organizational extension for Location Information." ::= { lldpXMedGroups 4 } lldpXMedOptPoEPSEGroup OBJECT-GROUP OBJECTS { lldpXMedLocXPoEPSEPortPowerAv, lldpXMedLocXPoEPSEPortPDPriority, lldpXMedLocXPoEPSEPowerSource } STATUS current DESCRIPTION "The collection of objects which are used to represent LLDP MED organizational extensions for PoE PSE Information." ::= { lldpXMedGroups 5 } lldpXMedOptPoEPDGroup OBJECT-GROUP OBJECTS { lldpXMedLocXPoEPDPowerReq, lldpXMedLocXPoEPDPowerSource, lldpXMedLocXPoEPDPowerPriority } STATUS current DESCRIPTION "The collection of objects which are used to represent LLDP MED organizational extensions for PoE PD Information." ::= { lldpXMedGroups 6 } lldpXMedRemSysGroup OBJECT-GROUP OBJECTS { lldpXMedRemCapSupported, lldpXMedRemCapCurrent, lldpXMedRemDeviceClass, lldpXMedRemMediaPolicyVlanID, lldpXMedRemMediaPolicyPriority, lldpXMedRemMediaPolicyDscp, lldpXMedRemMediaPolicyUnknown, lldpXMedRemMediaPolicyTagged, lldpXMedRemHardwareRev, lldpXMedRemFirmwareRev, lldpXMedRemSoftwareRev, lldpXMedRemSerialNum, lldpXMedRemMfgName, lldpXMedRemModelName, lldpXMedRemAssetID, lldpXMedRemLocationInfo, lldpXMedRemXPoEDeviceType, lldpXMedRemXPoEPSEPowerAv, lldpXMedRemXPoEPSEPowerSource, lldpXMedRemXPoEPSEPowerPriority, lldpXMedRemXPoEPDPowerReq, lldpXMedRemXPoEPDPowerSource, lldpXMedRemXPoEPDPowerPriority } STATUS current DESCRIPTION "The collection of objects which are used to represent LLDP- MED organizational extension Remote Device Information." ::= { lldpXMedGroups 7 } lldpXMedNotificationsGroup NOTIFICATION-GROUP NOTIFICATIONS { lldpXMedTopologyChangeDetected } STATUS current DESCRIPTION "Notifications sent by an LLDP-MED agent." ::= { lldpXMedGroups 8 } END