-- ***************************************************************** -- L A N O P T I C S - R I N G - M A N A G E R - M I B . m y -- -- March 1996, Keith Horil -- -- Copyright (c) 1996 by cisco Systems, Inc. -- All rights reserved. -- ***************************************************************** -- -- This mib was developed by LanOptics LANOPTICS-RING-MANAGER-MIB DEFINITIONS ::= BEGIN -- MIB II Definitions for Ring Manager Option IMPORTS OBJECT-TYPE FROM RFC-1212 enterprises, Counter, IpAddress FROM RFC1155-SMI DisplayString, PhysAddress FROM RFC1213-MIB; BITMAP ::= INTEGER RING-CONFIGURATION ::= OCTET STRING lanOptics OBJECT IDENTIFIER ::= { enterprises 224 } lanOpticsDot5Monitor OBJECT IDENTIFIER ::= { lanOptics 5 } -- This extension will implement some of RFC1231 for the -- Management module in the Hub if Token-Ring is installed. rmServerReportingTo OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "This gives the IP address for the reporting manager." ::= { lanOpticsDot5Monitor 1 } rmRingStatus OBJECT-TYPE SYNTAX INTEGER { -- normal (0) , beaconing (1) , single-station (2) , errors-increasing (3) , excessive-errors (4) } ACCESS read-only STATUS mandatory DESCRIPTION "This variable indicates the curent ring status." ::= { lanOpticsDot5Monitor 2 } rmServerHealthText OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable describes the status of the ring server in a textural manner." ::= { lanOpticsDot5Monitor 3 } rmServerHealth OBJECT-TYPE SYNTAX INTEGER { -- normal (0) , initial-State (1) , not-Active (2) } ACCESS read-only STATUS mandatory DESCRIPTION "This variable will describe the status of the ring server." ::= { lanOpticsDot5Monitor 4 } rmRingEventInLog OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of events currently in the internal event log." ::= { lanOpticsDot5Monitor 5 } rmRingEventTable OBJECT-TYPE SYNTAX SEQUENCE OF RmRingEventEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing the last events. The detailed structure is TBD." ::= { lanOpticsDot5Monitor 6 } rmRingEventEntry OBJECT-TYPE SYNTAX RmRingEventEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing one event. The index into the table is the event number (32 bits int), where each byte represented by an index digit." INDEX { INTEGER , INTEGER , INTEGER , INTEGER } ::= { rmRingEventTable 1 } RmRingEventEntry ::= SEQUENCE{ rmRingEvent OCTET STRING } rmRingEvent OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "This variable will give the data structure describing a ring event in an internal format" ::= { rmRingEventEntry 1 } rmRingBeaconingStatus OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "This variable will give the data structure describing the beaconing state of the ring." ::= { lanOpticsDot5Monitor 7 } rmRingIsoErrorStatus OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "This variable will give the data structure describing the isolating error state of the ring." ::= { lanOpticsDot5Monitor 8 } rmRingSingleStationStatus OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "This variable will give the data structure describing the single station state of the ring." ::= { lanOpticsDot5Monitor 9 } rmRingFullConfiguration OBJECT-TYPE SYNTAX RING-CONFIGURATION ACCESS read-only STATUS mandatory DESCRIPTION "This variable gives the ring configuration as known to the server. Each MAC address is represented by 6 bytes. The direction is up-stream." ::= { lanOpticsDot5Monitor 10 } rmRingConfigurationUpdate OBJECT-TYPE SYNTAX RING-CONFIGURATION ACCESS read-only STATUS mandatory DESCRIPTION "This variable will give a sequence of changes in the ring configuration for the monitored ring." ::= { lanOpticsDot5Monitor 11 } rmServerInitProcess OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This variable will initialize the server (reset the management module)." ::= { lanOpticsDot5Monitor 12 } rmServerAdminState OBJECT-TYPE SYNTAX BITMAP ACCESS read-write STATUS mandatory DESCRIPTION "This variable will indicate administrative status of the server. IDLE - 0 The bit # (LSB = 0): REM - bit 0 on CRS - bit 1 on RPS - bit 2 on LBS - bit 3 on" ::= { lanOpticsDot5Monitor 13 } rmServerOperatingState OBJECT-TYPE SYNTAX BITMAP ACCESS read-only STATUS mandatory DESCRIPTION "This variable will indicate operating status of the server: IDLE - all 0 The bit # (LSB = 0): REM - bit 0 on CRS - bit 1 on RPS - bit 2 on LBS - bit 3 on" ::= { lanOpticsDot5Monitor 14 } rmServerAdminParameters OBJECT-TYPE SYNTAX BITMAP ACCESS read-write STATUS mandatory DESCRIPTION "The required bit per event disabled/enabled. The bit # (LSB = 0): Nullevent(0), Nodenoresponseevent(1), Pollprocessfailevent(2), Criticnodejoinedringevent(3), Noderemovedevent(4), Activemonitorerrorevent(5), Newactivemonitorevent(6), Naunchangeevent(7), Claimtokenevent(8), Ringpurgeevent(9), Activemonitorpresentevent(10), Standbymonitorpresentevent(11), Softerrorreportevent(12), Ringstatusevent(13), Congestthresholdexccededevent(14), Congestthresholdendedevent(15), Nonisolatingthresholdexccededevent(16), Impendthresholdexccededevent(17), Excessivethresholdexcededevent(18), Errorratedecayevent(19), Adaptererrorevent(20), Responseevent(21), Pollprocessevent(22), Beaconevent(23), Nodeleftringevent(24), Nodejoinedringevent(25), Criticnodeleftringevent(26)" ::= { lanOpticsDot5Monitor 15 } rmServerOperatingParameters OBJECT-TYPE SYNTAX BITMAP ACCESS read-only STATUS mandatory DESCRIPTION "The required bit per event disabled/enabled. The bit # (LSB = 0): Nullevent(0), Nodenoresponseevent(1), Pollprocessfailevent(2), Criticnodejoinedringevent(3), Noderemovedevent(4), Activemonitorerrorevent(5), Newactivemonitorevent(6), Naunchangeevent(7), Claimtokenevent(8), Ringpurgeevent(9), Activemonitorpresentevent(10), Standbymonitorpresentevent(11), Softerrorreportevent(12), Ringstatusevent(13), Congestthresholdexccededevent(14), Congestthresholdendedevent(15), Nonisolatingthresholdexccededevent(16), Impendthresholdexccededevent(17), Excessivethresholdexcededevent(18), Errorratedecayevent(19), Adaptererrorevent(20), Responseevent(21), Pollprocessevent(22), Beaconevent(23), Nodeleftringevent(24), Nodejoinedringevent(25), Criticnodeleftringevent(26)" ::= { lanOpticsDot5Monitor 16 } rmDeviceStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF RmDeviceEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing device parameters and configuration." ::= { lanOpticsDot5Monitor 17 } rmDeviceEntry OBJECT-TYPE SYNTAX RmDeviceEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing device parameters and configuration. The index to the table is the MAC address of the device." INDEX { rmDeviceMacAddress } ::= { rmDeviceStatusTable 1 } RmDeviceEntry ::= SEQUENCE{ rmDeviceMacAddress PhysAddress, rmDeviceUpstream PhysAddress, rmDeviceAdminState INTEGER, rmDeviceOperateState INTEGER, rmDevicePhysLocation INTEGER, rmDeviceGroupAddress INTEGER, rmDeviceFunctionAddress INTEGER, rmDeviceProductID OCTET STRING, rmDeviceStationID INTEGER, rmDeviceStationStatus OCTET STRING, rmDeviceFunctionClass INTEGER, rmDeviceAccessPriority INTEGER, rmDeviceMicroLevel OCTET STRING, rmDeviceMonitored INTEGER, rmDeviceDaysAllowed INTEGER, rmDeviceHoursAllowed INTEGER } rmDeviceMacAddress OBJECT-TYPE SYNTAX PhysAddress ACCESS read-only STATUS mandatory ::= { rmDeviceEntry 1 } rmDeviceUpstream OBJECT-TYPE SYNTAX PhysAddress ACCESS read-only STATUS mandatory ::= { rmDeviceEntry 2 } rmDeviceAdminState OBJECT-TYPE SYNTAX INTEGER { removed (4) } ACCESS read-write STATUS mandatory DESCRIPTION "The required state of the adapter. - only removed is supported." ::= { rmDeviceEntry 3 } rmDeviceOperateState OBJECT-TYPE SYNTAX INTEGER { open (1), closed (2), removed (4), neverInserted (8) } ACCESS read-only STATUS mandatory DESCRIPTION " The operating state of the adapter." ::= { rmDeviceEntry 4 } rmDevicePhysLocation OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { rmDeviceEntry 5 } rmDeviceGroupAddress OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { rmDeviceEntry 6 } rmDeviceFunctionAddress OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { rmDeviceEntry 7 } rmDeviceProductID OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory ::= { rmDeviceEntry 8 } rmDeviceStationID OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { rmDeviceEntry 9 } rmDeviceStationStatus OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory ::= { rmDeviceEntry 10 } rmDeviceFunctionClass OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { rmDeviceEntry 11 } rmDeviceAccessPriority OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { rmDeviceEntry 12 } rmDeviceMicroLevel OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory ::= { rmDeviceEntry 13 } rmDeviceMonitored OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { rmDeviceEntry 14 } rmDeviceDaysAllowed OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { rmDeviceEntry 15 } rmDeviceHoursAllowed OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { rmDeviceEntry 16 } rmRingPollProcessStatus OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "This variable will give the data structure describing the poll process status of the ring." ::= { lanOpticsDot5Monitor 18 } -- variables 18 to 34 are currently not supported -- -- rmRingIsoImpendingThreshold OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-write -- STATUS mandatory -- DESCRIPTION --This variable will give the isolating soft error --mpending threshold." -- ::= { lanOpticsDot5Monitor 19 } -- -- rmRingIsoExcessiveThreshold OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-write -- STATUS mandatory -- DESCRIPTION --This variable will give the isolating soft error --xcessive threshold." -- ::= { lanOpticsDot5Monitor 20 } -- -- rmRingIsoDecrementValue OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-write -- STATUS mandatory -- DESCRIPTION --This variable will give the isolating soft error --ecrement value." -- ::= { lanOpticsDot5Monitor 21 } -- -- rmRingIsoDecrementInterval OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-write -- STATUS mandatory -- DESCRIPTION --This variable will give the isolating soft error --ecrement time interval." -- ::= { lanOpticsDot5Monitor 22 } -- -- rmRingCongestionTabThreshold OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-write -- STATUS mandatory -- DESCRIPTION --This variable will give the Congestion --hreshold." -- ::= { lanOpticsDot5Monitor 23 } -- -- rmRingLostFramesThreshold OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-write -- STATUS mandatory -- DESCRIPTION --This variable will give the non isolating --ost frames soft error threshold." -- ::= { lanOpticsDot5Monitor 24 } -- -- rmRingReceiveCongestThreshold OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-write -- STATUS mandatory -- DESCRIPTION --This variable will give the non isolating --eceiver congestion soft error threshold." -- ::= { lanOpticsDot5Monitor 25 } -- -- rmRingFrameCopiedErrorThreshold OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-write -- STATUS mandatory -- DESCRIPTION --This variable will give the non isolating --rame copied error soft error threshold." -- ::= { lanOpticsDot5Monitor 26 } -- -- rmRingFrequencyErrorThreshold OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-write -- STATUS mandatory -- DESCRIPTION --This variable will give the non isolating --requency error soft error threshold." -- ::= { lanOpticsDot5Monitor 27 } -- -- rmRingTokenErrorThreshold OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-write -- STATUS mandatory -- DESCRIPTION --This variable will give the non isolating --oken error soft error threshold." -- ::= { lanOpticsDot5Monitor 28 } -- -- rmRingIsoTabFullThreshold OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-write -- STATUS mandatory -- DESCRIPTION --This variable will give the non isolating --so table full error threshold." -- ::= { lanOpticsDot5Monitor 29 } -- -- rmRingMinDecrementThreshold OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-write -- STATUS mandatory -- DESCRIPTION --This variable will give the non isolating --inimum decrement error soft error threshold." -- ::= { lanOpticsDot5Monitor 30 } -- -- rmRingCongestTabFullThreshold OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-write -- STATUS mandatory -- DESCRIPTION --This variable will give the non isolating --ongestion table full error threshold." -- ::= { lanOpticsDot5Monitor 31 } -- -- rmServerMacBufFullThreshold OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-write -- STATUS mandatory -- DESCRIPTION --This variable will give the non isolating --AC addresses buffer full error threshold." -- ::= { lanOpticsDot5Monitor 32 } -- -- rmRingStatusBufFullThreshold OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-write -- STATUS mandatory -- DESCRIPTION --This variable will give the status change --uffer full threshold." -- ::= { lanOpticsDot5Monitor 33 } -- -- rmServerSoftwareVersion OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION --This variable will give the software version --f the server." -- ::= { lanOpticsDot5Monitor 34 } -- rmRingNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This variable will give the local ring number." ::= { lanOpticsDot5Monitor 35 } rmRingSoftErrorTimer OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This variable will give the ring soft error timer (in units of 10 milliseconds)." ::= { lanOpticsDot5Monitor 36 } rmRingIsolatingTab OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "This variable will give the ring isolating table." ::= { lanOpticsDot5Monitor 37 } rmRingCongestTab OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "This variable will give the ring congestion table." ::= { lanOpticsDot5Monitor 38 } rmRingNonIsolatingTab OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "This variable will give the ring non isolating table." ::= { lanOpticsDot5Monitor 39 } -- variables 40 - 41 currently not supported -- rmRingExcToNormal OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-write -- STATUS mandatory -- DESCRIPTION --This variable will give the ring excessive to --ormal threshold." -- ::= { lanOpticsDot5Monitor 40 } -- -- rmRingImpToNormal OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-write -- STATUS mandatory -- DESCRIPTION --This variable will give the ring impending to --ormal threshold." -- ::= { lanOpticsDot5Monitor 41 } rmRingAutoRemove OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This variable will enable/disable auto removal of a node when the isolating threshold is exceeded or the congestion threshold is exceeded." ::= { lanOpticsDot5Monitor 42 } rmRingAllowedDaysPartition1 OBJECT-TYPE SYNTAX INTEGER (1..7) ACCESS read-write STATUS mandatory DESCRIPTION "This variable is the first partition in the days time exis. The partitions define ranges in units of days in which some device are allowed to enter the ring and some are not." ::= { lanOpticsDot5Monitor 43 } rmRingAllowedDaysPartition2 OBJECT-TYPE SYNTAX INTEGER (1..7) ACCESS read-write STATUS mandatory DESCRIPTION "This variable is the second partition in the days time exis. The partitions define ranges in units of days in which some devices are allowed to enter the ring and some are not. The value should be higher than Partition1" ::= { lanOpticsDot5Monitor 44 } rmRingAllowedHoursPartition1 OBJECT-TYPE SYNTAX INTEGER (1..24) ACCESS read-write STATUS mandatory DESCRIPTION "This variable is the first partition in the hours time exis. The partitions define ranges in units of hours (1-24 hours) in which some devices are allowed to enter the ring and some are not." ::= { lanOpticsDot5Monitor 45 } rmRingAllowedHoursPartition2 OBJECT-TYPE SYNTAX INTEGER (1..24) ACCESS read-write STATUS mandatory DESCRIPTION "This variable is the second partition in the hours time exis. The partitions define ranges in units of hours (1-24 hours) in which some devices are allowed to enter the ring and some are not. The value should be higher than Partition1." ::= { lanOpticsDot5Monitor 46 } rmServerPowerOn OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This variable indicates if the server is powered on since the last poll." ::= { lanOpticsDot5Monitor 47 } -- Token-ring related alerts data rmTRLastErrorClass OBJECT-TYPE SYNTAX INTEGER{ -- no-error(0), adapter-error(1), beaconing(2), iso-increasing (3), iso-excessive (4), iso-decay (5), congestion (6) } ACCESS read-only STATUS mandatory DESCRIPTION "This var contains the error class of the last Token-Ring error reported by the agent." ::= { lanOpticsDot5Monitor 48 } rmTRLastErrorType OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This var contains the error type of the last Token-Ring error, depending on the error class" ::= { lanOpticsDot5Monitor 49 } rmTRFaultDomainNode1 OBJECT-TYPE SYNTAX PhysAddress ACCESS read-only STATUS mandatory DESCRIPTION "This var contains the MAC address of the first node in the last error fault domain." ::= { lanOpticsDot5Monitor 50 } rmTRFaultDomainNode2 OBJECT-TYPE SYNTAX PhysAddress ACCESS read-only STATUS mandatory DESCRIPTION "This var contains the MAC address of the second node in the last error fault domain." ::= { lanOpticsDot5Monitor 51 } -- Token ring events counters rmIsoTresholdExceededCount OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This var counts the total number that Isloating Treshold has been exceeded (exessive error status of the ring) since the agent is up or reset." ::= { lanOpticsDot5Monitor 52 } rmNonIsoTresholdExceededCount OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This var counts the total number that Non Isloating Treshold has been exceeded since the agent is up." ::= { lanOpticsDot5Monitor 53 } rmCongestionTresholdExceededCount OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This var counts the total number that Congestion Treshold has been exceeded since the agent is up." ::= { lanOpticsDot5Monitor 54 } rmBeaconCounter OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This var counts the total number of Beacons for the whole ring since the agent is up." ::= { lanOpticsDot5Monitor 55 } rmSpareCounter OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Spare Counter for future use" ::= { lanOpticsDot5Monitor 56 } rmPurgeCounter OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This var counts the total number of ring Purges since the agent is up." ::= { lanOpticsDot5Monitor 57 } rmClaimCounter OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This var counts the total number of Token Claims since the agent is up." ::= { lanOpticsDot5Monitor 58 } rmAdapterResetCounter OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This var counts the total number of times the agent adapter has to reset itself since the agent is up." ::= { lanOpticsDot5Monitor 59 } rmLostFramesCounter OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This var counts the total number of Lost Frames events for the whole ring since the agent is up." ::= { lanOpticsDot5Monitor 60 } rmCongestionCounter OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This var counts the total number of Congestion events for the whole ring since the agent is up." ::= { lanOpticsDot5Monitor 61 } rmFrameCopyCounter OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This var counts the total number of Frame Copy events for the whole ring since the agent is up." ::= { lanOpticsDot5Monitor 62 } rmFrequencyErrorCounter OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This var counts the total number of Frequency Error events for the whole ring since the agent is up." ::= { lanOpticsDot5Monitor 63 } rmTokenCounter OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This var counts the total number of Token error events for the whole ring since the agent is up." ::= { lanOpticsDot5Monitor 64 } rmLineCounter OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This var counts the total number of Line error events for the whole ring since the agent is up." ::= { lanOpticsDot5Monitor 65 } rmInternalCounter OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This var counts the total number of Internal error events for the whole ring since the agent is up." ::= { lanOpticsDot5Monitor 66 } rmBurstCounter OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This var counts the total number of Burst error events for the whole ring since the agent is up." ::= { lanOpticsDot5Monitor 67 } rmARIFCICounter OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This var counts the total number of ARI/FCI events for the whole ring since the agent is up." ::= { lanOpticsDot5Monitor 68 } rmAbortCounter OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This var counts the total number of Abort events for the whole ring since the agent is up." ::= { lanOpticsDot5Monitor 69 } rmPollFailCounter OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This var counts the total number of Poll Failed events for the whole ring since the agent is up." ::= { lanOpticsDot5Monitor 70 } rmNoResponseCounter OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This var counts the total number of No Response events for the whole ring since the agent is up." ::= { lanOpticsDot5Monitor 71 } rmWholeRingCounters OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "This var counts a list of all the above counters (52-71) for convenience. Each counter occupies 32 bits of this structure in the order of the related variables. For internal use only." ::= { lanOpticsDot5Monitor 72 } rmResetOldDevicesSetup OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This var resets existing agent setup for all devices, e.g: monitored, not-allowed, etc." ::= { lanOpticsDot5Monitor 73 } rmResetErrorCounters OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This var resets existing agent error counters." ::= { lanOpticsDot5Monitor 74 } rmSetCurrentTime OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This var sets the current time (for security settings). The time is the number of seconds elapsed since midnight, December 31, 1899. " ::= { lanOpticsDot5Monitor 75 } rmRingFirstSplitConfiguration OBJECT-TYPE SYNTAX RING-CONFIGURATION ACCESS read-only STATUS mandatory DESCRIPTION "This variable will give the first part of the ring configuration upto 256 bytes including header (for agents with limited buffer for a single octet). Retrieving this variable and several 'nexts' enables to compose the whole ring configuration." ::= { lanOpticsDot5Monitor 76 } rmRingNextSplitConfiguration OBJECT-TYPE SYNTAX RING-CONFIGURATION ACCESS read-only STATUS mandatory DESCRIPTION "This variable will give the next part of the ring configuration relating to rmRingFirstSplitConfiguration or previous variable of this type. Upto 256 bytes are given (for agents with limited buffer for a single octet). See previous variable for more details." ::= { lanOpticsDot5Monitor 77 } END