-- **************************************************************************** -- -- Compaq Fibre Channel Array -- Management Information Base for SNMP Network Management -- -- -- Copyright 1997-2002, Compaq Computer Corporation. -- All Rights Reserved. -- -- The information in this document is subject to change without notice. -- -- COMPAQ COMPUTER CORPORATION SHALL NOT BE LIABLE FOR TECHNICAL -- OR EDITORIAL ERRORS OR OMISSIONS CONATINED HEREIN; NOR FOR INCIDENTAL -- OR CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING, PERFORMANCE, -- OR USE OF THIS MATERIAL. -- -- Refer to the READMIB.RDM file for more information about the -- organization of the information in the Compaq Enterprise. -- -- The Compaq Enterprise number is 232. -- The ASN.1 prefix to, and including the Compaq Enterprise is: -- 1.3.6.1.4.1.232 -- -- **************************************************************************** CPQFCA-MIB DEFINITIONS ::= BEGIN IMPORTS compaq FROM CPQHOST-MIB enterprises FROM RFC1155-SMI Counter FROM RFC1155-SMI Gauge FROM RFC1155-SMI DisplayString FROM RFC1213-MIB OBJECT-TYPE FROM RFC-1212 TRAP-TYPE FROM RFC-1215 sysName FROM RFC1213-MIB cpqHoTrapFlags FROM CPQHOST-MIB cpqSsChassisName FROM CPQSTSYS-MIB cpqSsChassisTime FROM CPQSTSYS-MIB; -- compaq OBJECT IDENTIFIER ::= { enterprises 232 } cpqFibreArray OBJECT IDENTIFIER ::= { compaq 16 } cpqFcaMibRev OBJECT IDENTIFIER ::= { cpqFibreArray 1 } cpqFcaComponent OBJECT IDENTIFIER ::= { cpqFibreArray 2 } cpqFcTapeComponent OBJECT IDENTIFIER ::= { cpqFibreArray 3 } cpqFcSwitchComponent OBJECT IDENTIFIER ::= { cpqFibreArray 4 } cpqFcaInterface OBJECT IDENTIFIER ::= { cpqFcaComponent 1 } cpqFcaCntlr OBJECT IDENTIFIER ::= { cpqFcaComponent 2 } cpqFcaLogDrv OBJECT IDENTIFIER ::= { cpqFcaComponent 3 } cpqFcaSpareDrv OBJECT IDENTIFIER ::= { cpqFcaComponent 4 } cpqFcaPhyDrv OBJECT IDENTIFIER ::= { cpqFcaComponent 5 } cpqFcaPhyDrvThr OBJECT IDENTIFIER ::= { cpqFcaComponent 6 } cpqFcaHostCntlr OBJECT IDENTIFIER ::= { cpqFcaComponent 7 } cpqFcaOsCommon OBJECT IDENTIFIER ::= { cpqFcaInterface 4 } cpqFcTapeCntlr OBJECT IDENTIFIER ::= { cpqFcTapeComponent 1 } cpqFcTapeLibrary OBJECT IDENTIFIER ::= { cpqFcTapeComponent 2 } cpqFcTapeDrive OBJECT IDENTIFIER ::= { cpqFcTapeComponent 3 } cpqFcTapeCounters OBJECT IDENTIFIER ::= { cpqFcTapeComponent 4 } cpqFcSwitch OBJECT IDENTIFIER ::= { cpqFcSwitchComponent 1 } -- **************************************************************************** -- Fibre Channel Array MIB Revision -- ========================= -- -- The compaq enterprise (1.3.6.1.4.1.232) -- cpqFibreArray Group (1.3.6.1.4.1.232.16) -- cpqFcaMibRev Group (1.3.6.1.4.1.232.16.1) -- -- An SNMP agent conforming to this document will return a -- cpqFcaMibRevMajor of one (1) and a cpqFcaMibRevMinor of twelve (12). -- -- Implementation of the cpqFcaMibRev group is mandatory for all agents -- supporting the Compaq Fibre Channel Array MIB. -- -- NOTE: The Compaq Fibre Channel Array MIB also supports SCSI attached -- external arrays, such as Compaq Smart Array Cluster Storage. -- -- **************************************************************************** cpqFcaMibRevMajor OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-only STATUS mandatory DESCRIPTION "The Major Revision level. A change in the major revision level represents a major change in the architecture of the MIB. A change in the major revision level may indicate a significant change in the information supported and/or the meaning of the supported information, correct interpretation of data may require a MIB document with the same major revision level." ::= { cpqFcaMibRev 1 } cpqFcaMibRevMinor OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "The Minor Revision level. A change in the minor revision level may represent some minor additional support, no changes to any pre-existing information has occurred." ::= { cpqFcaMibRev 2 } cpqFcaMibCondition OBJECT-TYPE SYNTAX INTEGER { other(1), ok(2), degraded(3), failed(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The overall condition (status) of the system represented by this MIB." ::= { cpqFcaMibRev 3 } -- **************************************************************************** -- Fibre Channel Array Common Group -- ================================ -- -- The compaq enterprise (1.3.6.1.4.1.232) -- cpqFibreArray Group (1.3.6.1.4.1.232.16) -- cpqFcaComponent Group (1.3.6.1.4.1.232.16.2) -- cpqFcaInterface Group (1.3.6.1.4.1.232.16.2.1) -- cpqFcaOsCommon Group (1.3.6.1.4.1.232.16.2.1.4) -- -- The cpqFcaOsCommon group describes the interface to the Fibre Channel -- Array components. This information describes the interface modules -- and general OS interface architectural information. -- -- Implementation of the cpqFcaOsCommon group is mandatory for all -- agents that support the Fibre Channel Array MIB. -- -- **************************************************************************** cpqFcaOsCommonPollFreq OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-write STATUS mandatory DESCRIPTION "The Insight Agent's polling frequency. The frequency, in seconds, at which the Insight Agent requests information from the device driver. A frequency of zero (0) indicates that the Insight Agent retrieves the information upon request of a management station, it does not poll the device driver at a specific interval. If the poll frequency is zero (0) all attempts to write to this object will fail. If the poll frequency is non-zero, setting this value will change the polling frequency of the Insight Agent. Setting the poll frequency to zero (0) will always fail, an agent may also choose to fail any request to change the poll frequency to a value that would severely impact system performance." ::= { cpqFcaOsCommon 1 } -- **************************************************************************** -- Fibre Channel Array Common Module -- ================================= -- -- The compaq enterprise (1.3.6.1.4.1.232) -- cpqFibreArray Group (1.3.6.1.4.1.232.16) -- cpqFcaComponent Group (1.3.6.1.4.1.232.16.2) -- cpqFcaInterface Group (1.3.6.1.4.1.232.16.2.1) -- cpqFcaOsCommon Group (1.3.6.1.4.1.232.16.2.1.4) -- cpqFcaOsCommonModuleTable (1.3.6.1.4.1.232.16.2.1.4.2) deprecated -- -- **************************************************************************** cpqFcaOsCommonModuleTable OBJECT-TYPE SYNTAX SEQUENCE OF CpqFcaOsCommonModuleEntry ACCESS not-accessible STATUS deprecated DESCRIPTION "A table of software modules that provide an interface to the device this MIB describes." ::= { cpqFcaOsCommon 2 } cpqFcaOsCommonModuleEntry OBJECT-TYPE SYNTAX CpqFcaOsCommonModuleEntry ACCESS not-accessible STATUS deprecated DESCRIPTION "A description of a software module that provides an interface to the device this MIB describes." INDEX { cpqFcaOsCommonModuleIndex } ::= { cpqFcaOsCommonModuleTable 1 } CpqFcaOsCommonModuleEntry ::= SEQUENCE { cpqFcaOsCommonModuleIndex INTEGER, cpqFcaOsCommonModuleName DisplayString, cpqFcaOsCommonModuleVersion DisplayString, cpqFcaOsCommonModuleDate OCTET STRING, cpqFcaOsCommonModulePurpose DisplayString } cpqFcaOsCommonModuleIndex OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS deprecated DESCRIPTION "A unique index for this module description." ::= { cpqFcaOsCommonModuleEntry 1 } cpqFcaOsCommonModuleName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) ACCESS read-only STATUS deprecated DESCRIPTION "The module name." ::= { cpqFcaOsCommonModuleEntry 2 } cpqFcaOsCommonModuleVersion OBJECT-TYPE SYNTAX DisplayString (SIZE (0..5)) ACCESS read-only STATUS deprecated DESCRIPTION "The module version in XX.YY format. Where XX is the major version number and YY is the minor version number. This field will be a null (size 0) string if the agent cannot provide the module version." ::= { cpqFcaOsCommonModuleEntry 3 } cpqFcaOsCommonModuleDate OBJECT-TYPE SYNTAX OCTET STRING (SIZE (7)) ACCESS read-only STATUS deprecated DESCRIPTION "The module date. field octets contents range ===== ====== ======= ===== 1 1-2 year 0..65536 2 3 month 1..12 3 4 day 1..31 4 5 hour 0..23 5 6 minute 0..59 6 7 second 0..60 (use 60 for leap-second) This field will be set to year = 0 if the agent cannot provide the module date. The hour, minute, and second field will be set to zero (0) if they are not relevant. The year field is set with the most significant octect first." ::= { cpqFcaOsCommonModuleEntry 4 } cpqFcaOsCommonModulePurpose OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) ACCESS read-only STATUS deprecated DESCRIPTION "The purpose of the module described in this entry." ::= { cpqFcaOsCommonModuleEntry 5 } -- **************************************************************************** -- Fibre Channel Array Controller Group -- ==================================== -- -- The compaq enterprise (1.3.6.1.4.1.232) -- cpqFibreArray Group (1.3.6.1.4.1.232.16) -- cpqFcaComponent Group (1.3.6.1.4.1.232.16.2) -- cpqFcaCntlr Group (1.3.6.1.4.1.232.16.2.2) -- cpqFcaCntlrTable (1.3.6.1.4.1.232.16.2.2.1) -- -- The Cntlr group contains the configuration and statistical -- information of the Fibre Channel Array controllers and -- controller accelerator daughter boards. -- -- Implementation of the cpqFcaCntlr group is mandatory for all -- agents that support the Compaq Fibre Channel Array MIB. -- -- **************************************************************************** cpqFcaCntlrTable OBJECT-TYPE SYNTAX SEQUENCE OF CpqFcaCntlrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Compaq Fibre Channel Array Controller Table." ::= { cpqFcaCntlr 1 } cpqFcaCntlrEntry OBJECT-TYPE SYNTAX CpqFcaCntlrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Compaq Array Controller Entry." INDEX { cpqFcaCntlrBoxIndex, cpqFcaCntlrBoxIoSlot } ::= { cpqFcaCntlrTable 1 } CpqFcaCntlrEntry ::= SEQUENCE { cpqFcaCntlrBoxIndex INTEGER, cpqFcaCntlrBoxIoSlot INTEGER, cpqFcaCntlrModel INTEGER, cpqFcaCntlrFWRev DisplayString, cpqFcaCntlrStatus INTEGER, cpqFcaCntlrCondition INTEGER, cpqFcaCntlrProductRev DisplayString, cpqFcaCntlrWorldWideName DisplayString, cpqFcaCntlrSerialNumber DisplayString, cpqFcaCntlrCurrentRole INTEGER, cpqFcaCntlrRedundancyType INTEGER, cpqFcaCntlrRedundancyError INTEGER, cpqFcaCntlrBlinkTime Counter } cpqFcaCntlrBoxIndex OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Array Controller Storage Box Index. The storage box index indicates which storage box this controller is in." ::= { cpqFcaCntlrEntry 1 } cpqFcaCntlrBoxIoSlot OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Array Controller Box I/O Slot. This identifies the physical I/O slot where this controller resides in the storage box." ::= { cpqFcaCntlrEntry 2 } cpqFcaCntlrModel OBJECT-TYPE SYNTAX INTEGER { other(1), fibreArray(2), msa1000(3), smartArrayClusterStorage(4), hsg80(5), hsv110(6) } ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Array Controller Model. The type of controller card. The valid types are: Other (1) You may need to upgrade your driver software and\or instrument agent(s). You have an array controller in the storage box that the instrument agent does not recognize. fibreArray (2) Compaq StorageWorks RAID Array 4000 Controller. msa1000 (3) Compaq StorageWorks Modular SAN Array 1000 Controller. smartArrayClusterStorage (4) Compaq Smart Array Cluster Storage Controller. hsg80 (5) Compaq StorageWorks HSG80 RAID Array Controller. hsv110 (6) Compaq StorageWorks HSV110 Virtual Array Controller." ::= { cpqFcaCntlrEntry 3 } cpqFcaCntlrFWRev OBJECT-TYPE SYNTAX DisplayString (SIZE (0..5)) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Array Controller Firmware Revision. This value can be used to help identify a particular revision of the controller." ::= { cpqFcaCntlrEntry 4 } cpqFcaCntlrStatus OBJECT-TYPE SYNTAX INTEGER { other(1), ok(2), failed(3), offline(4) } ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Array Controller Status. This value represents the status of the Compaq Fibre Channel Array Controller." ::= { cpqFcaCntlrEntry 5 } cpqFcaCntlrCondition OBJECT-TYPE SYNTAX INTEGER { other(1), ok(2), degraded(3), failed(4) } ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Array Controller Condition. This value represents the overall condition of this controller and any array accelerators." ::= { cpqFcaCntlrEntry 6 } cpqFcaCntlrProductRev OBJECT-TYPE SYNTAX DisplayString (SIZE (0..1)) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Array Controller Product Revision. The Product Revision of the controller. This value can be used to further identify a particular revision of the controller model. This will be one character ASCII value that is zero terminated. If the controller model or the firmware does not support the product revision, the agents will return a NULL string." ::= { cpqFcaCntlrEntry 7 } cpqFcaCntlrWorldWideName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..16)) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Controller World Wide Name. This value can be used to further identify a particular controller. If the world wide name is not supported, the agent will return a NULL string." ::= { cpqFcaCntlrEntry 8 } cpqFcaCntlrSerialNumber OBJECT-TYPE SYNTAX DisplayString (SIZE (0..32)) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Controller Serial Number. This value can be used to further identify a particular controller. If the serial number is not supported, the agent will return a NULL string." ::= { cpqFcaCntlrEntry 9 } cpqFcaCntlrCurrentRole OBJECT-TYPE SYNTAX INTEGER { other(1), notDuplexed(2), active(3), backup(4) } ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Controller Current Role. For duplexed controllers, this is the controllers current role. The following values are valid: other (1) Indicates that the instrument agent does not recognize the role of the controller. You may need to upgrade the instrument agent. notDuplexed (2) This controller is not duplexed. active (3) This duplexed controller is the active controller. backup (4) This duplexed controller is the backup controller." ::= { cpqFcaCntlrEntry 10 } cpqFcaCntlrRedundancyType OBJECT-TYPE SYNTAX INTEGER { other(1), notRedundant(2), fwActiveStandby(3), fwPrimarySecondary(4) } ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Controller Redundancy Type. The following values are valid: other (1) Indicates that the instrument agent does not recognize the redundancy type of the controller. You may need to upgrade the instrument agent. notRedundant (2) The array controller is not in a redundant configuration. fwActiveStandby (3) The array controller is using an active/standby algorithm implemented in the controller firmware and the operating system driver. fwPrimarySecondary (4) The array controller is using a primary/secondary algorithm implemented in the controller firmware and the operating system driver." ::= { cpqFcaCntlrEntry 11 } cpqFcaCntlrRedundancyError OBJECT-TYPE SYNTAX INTEGER { other(1), noFailure(2), noRedundantController(3), differentHardware(4), noLink(5), differentFirmware(6), differentCache(7), otherCacheFailure(8), noDrives(9), otherNoDrives(10), unsupportedDrives(11), expandInProgress(12) } ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Controller Redundancy Error. The following values are valid: other (1) Indicates that the instrument agent does not recognize the redundancy error of the controller. You may need to upgrade the instrument agent. noFailure (2) No failures have been detected. noRedundantController (3) No redundant controller is installed. differentHardware (4) The other controller indicates a different hardware model. noLink (5) An inter-controller link to the other controller could not be established. differentFirmware (6) The other controller indicates a different firmware version. differentCache (7) The other controller indicates a different cache size. otherCacheFailure (8) The other controller indicates a cache failure. noDrives (9) This controller cannot see any attached drives, but the other controller can. otherNoDrives (10) This controller can see the attached drives, but the other controller cannot. unsupportedDrives (11) One or more attached drives has been determined to be incapable of properly supporting redundant controller operation. expandInProgress (12) Expand operation in progress. Redundant operation not supported until expand operation is complete." ::= { cpqFcaCntlrEntry 12 } cpqFcaCntlrBlinkTime OBJECT-TYPE SYNTAX Counter ACCESS read-write STATUS mandatory DESCRIPTION "External Array Controller Physical Drive Blink Time Count. The controller blink time variable allows the drive tray LEDs of all physical drives attached to this controller to blink. This value indicates the amount of time, in tenths of a second, that the physical drive LEDs will continue to blink. A value of zero indicates the drive LEDs are not blinking. If the value cannot be determined or no drive on this controller is in a hot plug tray, 4,294,967,295 is returned. To blink the drive LEDs on all physical drives attached to this controller, set this value to the time to blink in tenths of seconds. To stop the drive LEDs from blinking, set this value to 0." ::= { cpqFcaCntlrEntry 13 } -- **************************************************************************** -- Fibre Channel Array Accelerator Module Table -- ============================================ -- -- The compaq enterprise (1.3.6.1.4.1.232) -- cpqFibreArray Group (1.3.6.1.4.1.232.16) -- cpqFcaComponent Group (1.3.6.1.4.1.232.16.2) -- cpqFcaCntlr Group (1.3.6.1.4.1.232.16.2.2) -- cpqFcaAccelTable (1.3.6.1.4.1.232.16.2.2.2) -- -- **************************************************************************** cpqFcaAccelTable OBJECT-TYPE SYNTAX SEQUENCE OF CpqFcaAccelEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Array Accelerator Board Table." ::= { cpqFcaCntlr 2 } cpqFcaAccelEntry OBJECT-TYPE SYNTAX CpqFcaAccelEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Array Accelerator Board Entry." INDEX { cpqFcaAccelBoxIndex, cpqFcaAccelBoxIoSlot } ::= { cpqFcaAccelTable 1 } CpqFcaAccelEntry ::= SEQUENCE { cpqFcaAccelBoxIndex INTEGER, cpqFcaAccelBoxIoSlot INTEGER, cpqFcaAccelStatus INTEGER, cpqFcaAccelBadData INTEGER, cpqFcaAccelErrCode INTEGER, cpqFcaAccelBatteryStatus INTEGER, cpqFcaAccelReadErrs Counter, cpqFcaAccelWriteErrs Counter, cpqFcaAccelCondition INTEGER, cpqFcaAccelWriteCache INTEGER, cpqFcaAccelReadCache INTEGER, cpqFcaAccelSerialNumber DisplayString, cpqFcaAccelTotalMemory INTEGER } cpqFcaAccelBoxIndex OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Array Controller Storage Box Index. The storage box index indicates which storage box this accelerator is in." ::= { cpqFcaAccelEntry 1 } cpqFcaAccelBoxIoSlot OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Array Controller Box I/O Slot. This identifies the physical I/O slot where this accelerator resides in the storage box." ::= { cpqFcaAccelEntry 2 } cpqFcaAccelStatus OBJECT-TYPE SYNTAX INTEGER { other(1), invalid(2), enabled(3), tmpDisabled(4), permDisabled(5) } ACCESS read-only STATUS mandatory DESCRIPTION "Array Accelerator Board Status. This describes the status of the Compaq 4MB Array Accelerator Write Cache. The status can be: Other (1) Indicates that the instrument agent does not recognize the status of the Array Accelerator. You may need to upgrade the instrument agent. Invalid (2) Indicates that an Array Accelerator board has not been installed in this system. Enabled (3) Indicates that write cache operations are currently configured and enabled for at least one logical drive. Temporarily Disabled (4) Indicates that write cache operations have been temporarily disabled. View the Array Accelerator Board Error Code object to determine why the write cache operations have been temporarily disabled. Permanently Disabled (5) Indicates that write cache operations have been permanently disabled. View the Array Accelerator Board Error Code object to determine why the write cache operations have been disabled." ::= { cpqFcaAccelEntry 3 } cpqFcaAccelBadData OBJECT-TYPE SYNTAX INTEGER { other(1), none(2), possible(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Array Accelerator Board Bad Data. The following values are valid: None (2) Indicates that no data loss occurred. The battery packs were properly charged when the system was initialized. Possible (3) Indicates that at power up, the battery packs were not sufficiently charged. Because the batteries did not retain sufficient charge when the system resumed power, the board has not retained any data that may have been stored. If no data was on the board, no data was lost. Several things may have caused this condition: * If the system was without power for eight days, and the battery packs were on (battery packs only activate if system looses power unexpectedly), any data that may have been stored in the cache was lost. * There may be a problem with the battery pack. See the Battery Status for more information. * This status will also appear if the Array Accelerator board is replaced with a new board that has discharged batteries. No data has been lost in this case, and posted writes will automatically be enabled when the batteries reach full charge." ::= { cpqFcaAccelEntry 4 } cpqFcaAccelErrCode OBJECT-TYPE SYNTAX INTEGER { other(1), invalid(2), badConfig(3), lowBattery(4), disableCmd(5), noResources(6), notConnected(7), badMirrorData(8), readErr(9), writeErr(10), configCmd(11), expandInProgress(12), snapshotInProgress(13), redundantLowBattery(14), redundantSizeMismatch(15), redundantCacheFailure(16), excessiveEccErrors(17), postEccErrors(19) } ACCESS read-only STATUS mandatory DESCRIPTION "Array Accelerator Board Error Code. Use this to determine the status of the write cache operations. The status can be: Other (1) Indicates that the instrument agent does not recognize the error code. You may need to update your software. Invalid (2) Indicates that write cache operations are currently configured and enabled for at least one logical drive. No write cache errors have occurred. Bad Configuration (3) Indicates that write cache operations are temporarily disabled. The Array Accelerator board was configured for a different controller. This error could be caused if boards were switched from one system to another. Rerun the Compaq EISA Configuration Utility and ensure that the board has been properly configured for this system. Note: If data from another system was stored on the board, rerunning EISA Configuration will cause the data to be lost. Low Battery Power (4) Indicates that write cache operations are temporarily disabled due to insufficient battery power. Please view the Battery Status object instance for more information. Disable Command Issued (5) Indicates that write cache operations are temporarily disabled. The device driver issues this command when the server is taken down. This condition should not exist when the system regains power. No Resources Available (6) Indicates that write cache operations are temporarily disabled. The controller does not have sufficient resources to perform write cache operations. For example, when a replaced drive is being rebuilt, there will not be sufficient resources. Once the operation that requires the resources has completed, this condition will clear and write cache operations will resume. Board Not Connected (7) Indicates that write cache operations are temporarily disabled. The Array Accelerator board has been configured but is not currently attached to the controller. Check the alignment of the board and connections. Bad Mirror Data (8) Indicates that write cache operations have been permanently disabled. The Array Accelerator board stores mirrored copies of all data. If data exists on the board when the system is first powered up, the board performs a data compare test between the mirrored copies. If the data does not match, an error has occurred. Data may have been lost. Your board may need servicing. Read Failure (9) Indicates that write cache operations have been permanently disabled. The Array Accelerator board stores mirror copies of all data. While reading the data from the board, memory parity errors have occurred. Both copies were corrupted and cannot be retrieved. Data has been lost, and you should service the board. Write Failure (10) Indicates that write cache operations have been permanently disabled. This error occurs when an unsuccessful attempt was made to write data to the Array Accelerator board. Data could not be written to write cache memory in duplicate due to the detection of parity errors. This error does not indicate data loss. You should service the Array Accelerator board. Config Command (11) Indicates that write cache operations have been permanently disabled. The configuration of the logical drives has changed. You need to reconfigure the Array Accelerator board. Expand In Progress (12) Indicates that cache operations are temporarily disabled due to an expand of a logical drive. When the expand operation completes, the accelerator will be enabled. Snapshot In Progress (13) Indicates that cache operations are temporarily disabled due to a snapshot operation that is queued up or in progress. When the snapshot operation completes, the accelerator will be enabled. Redundant Low Battery (14) Indicates that cache operations are temporarily disabled. The redundant controller has insufficient cache battery power. Redundant Size Mismatch (15) Indicates that cache operations are temporarily disabled. The cache sizes on the redundant controllers do not match. Redundant Cache Failure (16) Indicates that cache operations are temporarily disabled. The cache on the redundant controller has failed. Excessive ECC Errors (17) Indicates that write cache operations have been permanently disabled. The number of cache lines experiencing excessive ECC errors has reached a preset limit. Power On Self Test (Post) ECC Errors (19) Indicates that write cache operations have been permanently disabled. The cache has been disabled due to a large number of ECC errors detected while testing the cache during Power On Self Test (Post)." ::= { cpqFcaAccelEntry 5 } cpqFcaAccelBatteryStatus OBJECT-TYPE SYNTAX INTEGER { other(1), ok(2), recharging(3), failed(4), degraded(5), notPresent(6) } ACCESS read-only STATUS mandatory DESCRIPTION "Array Accelerator Board Battery Status. This monitors the status of each battery pack on the board. The batteries can only recharge when the system has power applied. The following values are valid: Other (1) Indicates that the instrument agent does not recognize battery status. You may need to update your software. Ok (2) Indicates that a particular battery pack is fully charged. Charging (3) The battery power is less than 75%. The array controller is attempting to recharge the battery. A battery can take as long as 36 hours to fully recharge. After 36 hours, if the battery has not recharged, it is considered failed. Failed (4) The battery pack is below the sufficient voltage level and has not recharged in 36 hours. Your Array Accelerator board needs to be serviced. Degraded (5) The battery is still operating, however, one of the batteries in the pack has failed to recharge properly. Your Array Accelerator board should be serviced as soon as possible. NotPresent (6) There are no batteries associated with this controller." ::= { cpqFcaAccelEntry 6 } cpqFcaAccelReadErrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Array Accelerator Board Read Errors. This shows the total number of read memory parity errors that were detected while reading from the Array Accelerator board. The mirrored copy of data on the board can be accessed to obtain correct data if a memory parity errors occurs. Memory parity errors occur when the system detects that information has not been transferred correctly. A parity bit is included for each byte of information stored in memory. When the microprocessor reads or writes data, the system counts the value of the bits in each byte. If a total does not match the system's expectations, a parity error has occurred. A bad memory chip, memory corruption, or lack of refresh may cause memory parity errors." ::= { cpqFcaAccelEntry 7 } cpqFcaAccelWriteErrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Array Accelerator Board Write Errors. This shows the total number of write memory parity errors that were detected while writing to the Array Accelerator board. Write parity errors occur when the system detects that information has not been transferred to the Array Accelerator board correctly. A parity bit is included for each byte of information stored in memory. When the microprocessor reads or writes data, the system counts the value of the bits in each byte. If the total does not match the system's expectations, a parity error has occurred." ::= { cpqFcaAccelEntry 8 } cpqFcaAccelCondition OBJECT-TYPE SYNTAX INTEGER { other(1), ok(2), degraded(3), failed(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The condition of the device. This value represents the overall condition of this array accelerator." ::= { cpqFcaAccelEntry 9 } cpqFcaAccelWriteCache OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Write Cache Memory. This shows the amount of memory allocated for the write cache in megabytes. Because data is kept in duplicate (mirrored), the actual amount of usable memory is half the amount shown." ::= { cpqFcaAccelEntry 10 } cpqFcaAccelReadCache OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Read Cache Memory. This shows the amount of memory allocated for the read cache in megabytes." ::= { cpqFcaAccelEntry 11 } cpqFcaAccelSerialNumber OBJECT-TYPE SYNTAX DisplayString (SIZE (0..32)) ACCESS read-only STATUS mandatory DESCRIPTION "Array Accelerator Board Serial Number. This value can be used to further identify the cache controller. If the serial number is not supported, the agent will return a NULL string." ::= { cpqFcaAccelEntry 12 } cpqFcaAccelTotalMemory OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Array Accelerator Total Memory. This value is the total amount of accelerator memory in megabytes, including both battery-backed and non-battery-backed memory." ::= { cpqFcaAccelEntry 13 } -- **************************************************************************** -- Fibre Channel Array Logical Drive Table -- ======================================= -- -- The compaq enterprise (1.3.6.1.4.1.232) -- cpqFibreArray Group (1.3.6.1.4.1.232.16) -- cpqFcaComponent Group (1.3.6.1.4.1.232.16.2) -- cpqFcaLogDrv Group (1.3.6.1.4.1.232.16.2.3) -- cpqFcaLogDrvTable (1.3.6.1.4.1.232.16.2.3.1) -- -- The cpqFcaLogDrv group contains configuration and statistical -- information about the logical drives associated with Compaq Fibre -- Channel Array controllers. -- -- Implementation of the cpqFcaLogDrv group is mandatory for all agents -- that support the Compaq Fibre Channel Array MIB. -- -- **************************************************************************** cpqFcaLogDrvTable OBJECT-TYPE SYNTAX SEQUENCE OF CpqFcaLogDrvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Fibre Channel Array Logical Drive Table. A table of logical drive entries." ::= { cpqFcaLogDrv 1 } cpqFcaLogDrvEntry OBJECT-TYPE SYNTAX CpqFcaLogDrvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Fibre Channel Array Logical Drive Entry. A logical drive entry." INDEX { cpqFcaLogDrvBoxIndex, cpqFcaLogDrvIndex } ::= { cpqFcaLogDrvTable 1 } CpqFcaLogDrvEntry ::= SEQUENCE { cpqFcaLogDrvBoxIndex INTEGER, cpqFcaLogDrvIndex INTEGER, cpqFcaLogDrvFaultTol INTEGER, cpqFcaLogDrvStatus INTEGER, cpqFcaLogDrvAutoRel INTEGER, cpqFcaLogDrvPercentRebuild Gauge, cpqFcaLogDrvHasAccel INTEGER, cpqFcaLogDrvAvailSpares OCTET STRING, cpqFcaLogDrvSize INTEGER, cpqFcaLogDrvPhyDrvIDs OCTET STRING, cpqFcaLogDrvCondition INTEGER, cpqFcaLogDrvStripeSize INTEGER, cpqFcaLogDrvOsName DisplayString, cpqFcaLogDrvBlinkTime Counter } cpqFcaLogDrvBoxIndex OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Array Logical Drive Storage Box Index. The storage box index indicates which storage box this logical drive is in." ::= { cpqFcaLogDrvEntry 1 } cpqFcaLogDrvIndex OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Fibre Channel Array Logical Drive Index. This logical drive number keeps track of multiple instances of logical drives which are in the same storage box. For each storage box index value, the logical drive index starts at 1 and increments for each logical drive. ???" ::= { cpqFcaLogDrvEntry 2 } cpqFcaLogDrvFaultTol OBJECT-TYPE SYNTAX INTEGER { other(1), none(2), mirroring(3), dataGuard(4), distribDataGuard(5), advancedDataGuard(7) } ACCESS read-only STATUS mandatory DESCRIPTION "Logical Drive Fault Tolerance. This shows the fault tolerance mode of the logical drive. To change the fault tolerance mode, run the Compaq EISA Configuration Utility. The following values are valid for the Logical Drive Fault Tolerance: None (2) Fault tolerance is not enabled. If a physical drive reports an error, the data cannot be recovered by the Compaq Drive Array Controller. Mirroring (3) For each physical drive, there is a second physical drive containing identical data. If a drive fails, the data can be retrieved from the mirror drive. Data Guard (4) One of the physical drives is used as a data guard drive and contains the exclusive OR of the data on the remaining drives. If a failure is detected, the Compaq Fibre Channel Array Controller rebuilds the data using the data guard information plus information from the other drives. Distributed Data Guard (5) Distributed Data Guarding, sometimes referred to as RAID 5, is similar to Data Guarding, but instead of storing the parity information on one drive, the information is distributed across all of the drives. If a failure is detected, the Compaq Drive Array Controller rebuilds the data using the data guard information from all the drives. Advanced Data Guarding (7) Advanced Data Guarding (RAID ADG) is the fault tolerance method that provides the highest level of data protection. It 'stripes' data and parity across all the physical drives in the configuration to ensure the uninterrupted availability of uncorrupted data. This fault-tolerance method is similar to distributed data guard (RAID 5) in that parity data is distributed across all drives in the array, except in RAID ADG the capacity of multiple drives is used to store parity data. Assuming the capacity of 2 drives is used for parity data, this allows continued operation despite simultaneous failure of any 2 drives in the array, whereas RAID 4 and RAID 5 can only sustain failure of a single drive." ::= { cpqFcaLogDrvEntry 3 } cpqFcaLogDrvStatus OBJECT-TYPE SYNTAX INTEGER { other(1), ok(2), failed(3), unconfigured(4), recovering(5), readyForRebuild(6), rebuilding(7), wrongDrive(8), badConnect(9), overheating(10), shutdown(11), expanding(12), notAvailable(13), queuedForExpansion(14), hardError(15) } ACCESS read-only STATUS mandatory DESCRIPTION "Logical Drive Status. The logical drive can be in one of the following states: Ok (2) Indicates that the logical drive is in normal operation mode. Failed (3) Indicates that more physical drives have failed than the fault tolerance mode of the logical drive can handle without data loss. Unconfigured (4) Indicates that the logical drive is not configured. Recovering (5) Indicates that the logical drive is using Interim Recovery Mode. In Interim Recovery Mode, at least one physical drive has failed, but the logical drive's fault tolerance mode lets the drive continue to operate with no data loss. Ready Rebuild (6) Indicates that the logical drive is ready for Automatic Data Recovery. The physical drive that failed has been replaced, but the logical drive is still operating in Interim Recovery Mode. Rebuilding (7) Indicates that the logical drive is currently doing Automatic Data Recovery. During Automatic Data Recovery, fault tolerance algorithms restore data to the replacement drive. Wrong Drive (8) Indicates that the wrong physical drive was replaced after a physical drive failure. Bad Connect (9) Indicates that a physical drive is not responding. Overheating (10) Indicates that the storage box that contains the logical drive is overheating. The array is still functioning, but should be shutdown. Shutdown (11) Indicates that the storage box that contains the logical drive has overheated. The logical drive is no longer functioning. Expanding (12) Indicates that the logical drive is currently doing Automatic Data Expansion. During Automatic Data Expansion, fault tolerance algorithms redistribute logical drive data to the newly added physical drive. Not Available (13) Indicates that the logical drive is currently unavailable. If a logical drive is expanding and the new configuration frees additional disk space, this free space can be configured into another logical volume. If this is done, the new volume will be set to not available. Queued For Expansion (14) Indicates that the logical drive is ready for Automatic Data Expansion. The logical drive is in the queue for expansion. Hard Error (15) Indicates that a hard error occurred for this LUN." ::= { cpqFcaLogDrvEntry 4 } cpqFcaLogDrvAutoRel OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Array Controller Logical Drive Auto-Reliability Delay. This value indicates how many seconds the logical drive will wait with no requests before beginning Auto-Reliability monitoring. For example, the default value is five, so the logical drive will begin Auto-Reliability monitoring if it receives no requests for five seconds. If the value is zero, the logical drive will not perform Auto-Reliability monitoring. Auto-Reliability only operates if the logical drive is configured in one of the fault tolerance modes. If the logical drive receives a request while performing Auto-Reliability monitoring, the drive will stop monitoring to process the request. Once it has satisfied all incoming requests, the drive will wait for the Auto-Reliability delay to expire before returning to Auto-Reliability monitoring. Auto-Reliability monitoring is a process to insure the highest level of data reliability. In this process each disk is scanned to verify that all of the sectors in the array are readable. If the Auto-Reliability monitoring process detects any bad sectors on the drives, it automatically remaps these bad sectors where possible. If the value cannot be determined or is not applicable, the value is set to -1." ::= { cpqFcaLogDrvEntry 5 } cpqFcaLogDrvPercentRebuild OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Logical Drive Percent Rebuild. After a failed physical drive has been replaced, the physical drive must have its data rebuilt. This value the percent complete of the rebuild. When the value reaches 100, the rebuilding process is complete. The drive array continues to operate in interim recovery mode while a drive is rebuilding. When a logical volume is Expanding, the drive must redistribute the logical volume data across the physical drives. This value shows how many blocks of data still need to be redistributed. When the value reaches one hundred (100), the expand process is complete. The array continues to operate normally while the drive is expanding. This value is only valid if the Logical Drive Status is rebuilding (7) or expanding (12). If the value cannot be determined or a rebuild is not active, the value is set to 4,294,967,295." ::= { cpqFcaLogDrvEntry 6 } cpqFcaLogDrvHasAccel OBJECT-TYPE SYNTAX INTEGER { other(1), unavailable(2), enabled(3), disabled(4) } ACCESS read-only STATUS mandatory DESCRIPTION "Logical Drive Has Array Accelerator Board. This indicates whether the logical drive has an Array Accelerator board configured and enabled. The following values are valid: Other (1) Indicates that the instrument agent does not recognize the Array Accelerator board. You may need to upgrade your software. Unavailable (2) Indicates that there is no Array Accelerator board configured for this logical drive. Enabled (3) Indicates that the Array Accelerator board is configured and enabled for this logical drive. Run the Compaq EISA Configuration Utility to change this value. Disabled (4) Indicates that the Array Accelerator board is configured but not enabled for this logical drive. Run the Compaq EISA Configuration Utility to change this value." ::= { cpqFcaLogDrvEntry 7 } cpqFcaLogDrvAvailSpares OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..255)) ACCESS read-only STATUS mandatory DESCRIPTION "Fibre Channel Array Logical Drive Available Spares. This indicates if this logical drive has one or more spares designated for it that are not currently in use by another drive. Each octet present will be a physical drive ID that is an available spare for this logical drive. These are the same ID's which can be used as indexes into the physical drive table. An octet string of length zero indicates that there are no available spares for this logical drive." ::= { cpqFcaLogDrvEntry 8 } cpqFcaLogDrvSize OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Fibre Channel Array Logical Drive Size. This is the size of the logical drive in megabytes. This value is calculated using the value 1,048,576 (2^20) as a megabyte. Drive manufacturers sometimes use the number 1,000,000 as a megabyte when giving drive capacities so this value may differ from the advertised size of a drive." ::= { cpqFcaLogDrvEntry 9 } cpqFcaLogDrvPhyDrvIDs OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..255)) ACCESS read-only STATUS mandatory DESCRIPTION "Fibre Channel Array Logical Drive Physical Drive IDs. This lists the physical drive IDs which are associated with this logical drive. These are the same IDs which can be used as indices into the physical drive table. Each byte of the string is an index." ::= { cpqFcaLogDrvEntry 10 } cpqFcaLogDrvCondition OBJECT-TYPE SYNTAX INTEGER { other(1), ok(2), degraded(3), failed(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The Logical Drive condition. This value represents the overall condition of this logical drive and any associated physical drives." ::= { cpqFcaLogDrvEntry 11 } cpqFcaLogDrvStripeSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Fibre Channel Array Logical Drive Stripe Size. This is the size of a logical drive stripe in kilobytes." ::= { cpqFcaLogDrvEntry 12 } cpqFcaLogDrvOsName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) ACCESS read-only STATUS mandatory DESCRIPTION "Fibre Channel Array Logical Drive OS Name. The OS name for this array logical drive. This field will be a null (size 0) string if the agent does not support OS name." ::= { cpqFcaLogDrvEntry 13 } cpqFcaLogDrvBlinkTime OBJECT-TYPE SYNTAX Counter ACCESS read-write STATUS mandatory DESCRIPTION "External Array Logical Drive Physical Drive Blink Time Count. The logical drive blink time variable allows the drive tray LEDs of all physical drives in a logical drive to blink. This value indicates the amount of time, in tenths of a second, that the physical drive LEDs will continue to blink. A value of zero indicates the drive LEDs are not blinking. If the value cannot be determined or no drive in this logical drive is in a hot plug tray, 4,294,967,295 is returned. To blink the drive LEDs on all physical drives in this logical drive (including any configured spare drives), set this value to the time to blink in tenths of seconds. To stop the drive LEDs from blinking, set this value to 0." ::= { cpqFcaLogDrvEntry 14 } -- **************************************************************************** -- Fibre Channel Array Spare Drive Table -- ===================================== -- -- The compaq enterprise (1.3.6.1.4.1.232) -- cpqFibreArray Group (1.3.6.1.4.1.232.16) -- cpqFcaComponent Group (1.3.6.1.4.1.232.16.2) -- cpqFcaSpareDrv Group (1.3.6.1.4.1.232.16.2.4) -- cpqFcaSpareTable (1.3.6.1.4.1.232.16.2.4.1) -- -- The cpqFcaSpareDrv group contains configuration and statistical -- information about the spare drives associated with Compaq Fibre -- Channel Array controllers. -- -- Implementation of the cpqFcaSpareDrv group is mandatory for all -- agents that support the Compaq Fibre Channel Array MIB that have -- a spare configured. -- -- **************************************************************************** cpqFcaSpareTable OBJECT-TYPE SYNTAX SEQUENCE OF CpqFcaSpareEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Fibre Channel Array Spare Table. A table of spare entries." ::= { cpqFcaSpareDrv 1 } cpqFcaSpareEntry OBJECT-TYPE SYNTAX CpqFcaSpareEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Fibre Channel Array Spare Entry. An entry in the spare table." INDEX { cpqFcaSpareBoxIndex, cpqFcaSparePhyDrvIndex } ::= { cpqFcaSpareTable 1 } CpqFcaSpareEntry ::= SEQUENCE { cpqFcaSpareBoxIndex INTEGER, cpqFcaSparePhyDrvIndex INTEGER, cpqFcaSpareStatus INTEGER, cpqFcaSpareReplacedDrvBay INTEGER, cpqFcaSparePercentRebuild Gauge, cpqFcaSpareCondition INTEGER, cpqFcaSpareBusNumber INTEGER, cpqFcaSpareBay INTEGER, cpqFcaSpareReplacedDrvBusNumber INTEGER } cpqFcaSpareBoxIndex OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Array Spare Drive Storage Box Index. The storage box index indicates which storage box this spare drive is in." ::= { cpqFcaSpareEntry 1 } cpqFcaSparePhyDrvIndex OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Fibre Channel Array Spare Physical Drive Index. This index maps the spare to the physical drive it represents. The value of this index is the same as the one used with the physical drive table." ::= { cpqFcaSpareEntry 2 } cpqFcaSpareStatus OBJECT-TYPE SYNTAX INTEGER { other(1), inactive(2), failed(3), building(4), active(5) } ACCESS read-only STATUS mandatory DESCRIPTION "Spare Status. This shows the status of the on-line spare drive. The following values are valid for the spare status: Inactive (2) The monitored system has an on-line spare configured, but is not currently in use. Failed (3) The on-line spare has failed and is no longer available for use. Building (4) A physical drive has failed. Automatic Data Recovery is in progress to recover data to the on-line spare. Active (5) A physical drive has failed. Automatic Data Recovery is complete. The system is using the on-line spare as a replacement for the failed drive." ::= { cpqFcaSpareEntry 3 } cpqFcaSpareReplacedDrvBay OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Spare Replaced Drive Bay. If the spare status is active(6) or building(5), then this has the physical drive bay number of the replaced drive. If the value cannot be determined or is not applicable, the value is set to -1." ::= { cpqFcaSpareEntry 4 } cpqFcaSparePercentRebuild OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Fibre Channel Array Spare Percent Rebuild. If the spare status is building(5), then this is percent complete of of the rebuild. The data contained on the failed physical drive must be reconstructed from the fault tolerance data and copied to the spare so that the spare can function in place of the failed drive. When the number reaches one hundred (100), the building process is complete and the spare has replaced the physical drive. If the value cannot be determined or a rebuild is not active, the value is set to 4,294,967,295." ::= { cpqFcaSpareEntry 5 } cpqFcaSpareCondition OBJECT-TYPE SYNTAX INTEGER { other(1), ok(2), degraded(3), failed(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The Spare Drive condition. This value represents the overall condition of this spare drive and any associated physical drives." ::= { cpqFcaSpareEntry 6 } cpqFcaSpareBusNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Spare Drive SCSI Bus Number. The bus number indicates to which SCSI bus this spare drive is attached. The first instance is one and increments for each SCSI bus on a controller." ::= { cpqFcaSpareEntry 7 } cpqFcaSpareBay OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Fibre Channel Array Spare Drive Bay Location. This value matches the bay location where the physical drive has been installed. Each bay is labeled with a separate number so that you can identify the location of the drive." ::= { cpqFcaSpareEntry 8 } cpqFcaSpareReplacedDrvBusNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Spare Replaced Drive Bus Number. If the spare status is active(6) or building(5), then this has the physical drive bus number of the replaced drive. If the value cannot be determined or is not applicable, the value is set to -1." ::= { cpqFcaSpareEntry 9 } -- **************************************************************************** -- Fibre Channel Array Physical Drive Group -- ======================================== -- -- The compaq enterprise (1.3.6.1.4.1.232) -- cpqFibreArray Group (1.3.6.1.4.1.232.16) -- cpqFcaComponent Group (1.3.6.1.4.1.232.16.2) -- cpqFcaPhyDrv Group (1.3.6.1.4.1.232.16.2.5) -- cpqFcaPhyDrvTable (1.3.6.1.4.1.232.16.2.5.1) -- -- The cpqFcaPhyDrv group contains configuration and statistical -- information about the physical drives associated with Compaq Drive -- Array controllers. -- -- Implementation of the cpqFcaPhyDrv group is mandatory for all agents -- that support the Compaq Fibre Channel Array MIB. -- -- **************************************************************************** cpqFcaPhyDrvTable OBJECT-TYPE SYNTAX SEQUENCE OF CpqFcaPhyDrvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Fibre Channel Array Physical Drive Table. A table of physical drive entries." ::= { cpqFcaPhyDrv 1 } cpqFcaPhyDrvEntry OBJECT-TYPE SYNTAX CpqFcaPhyDrvEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Fibre Channel Array Physical Drive Entry. A physical drive entry." INDEX { cpqFcaPhyDrvBoxIndex, cpqFcaPhyDrvIndex } ::= { cpqFcaPhyDrvTable 1 } CpqFcaPhyDrvEntry ::= SEQUENCE { cpqFcaPhyDrvBoxIndex INTEGER, cpqFcaPhyDrvIndex INTEGER, cpqFcaPhyDrvModel DisplayString, cpqFcaPhyDrvFWRev DisplayString, cpqFcaPhyDrvBay INTEGER, cpqFcaPhyDrvStatus INTEGER, cpqFcaPhyDrvUsedReallocs Counter, cpqFcaPhyDrvRefHours Counter, cpqFcaPhyDrvHReads Counter, cpqFcaPhyDrvReads Counter, cpqFcaPhyDrvHWrites Counter, cpqFcaPhyDrvWrites Counter, cpqFcaPhyDrvHSeeks Counter, cpqFcaPhyDrvSeeks Counter, cpqFcaPhyDrvHardReadErrs Counter, cpqFcaPhyDrvRecvReadErrs Counter, cpqFcaPhyDrvHardWriteErrs Counter, cpqFcaPhyDrvRecvWriteErrs Counter, cpqFcaPhyDrvHSeekErrs Counter, cpqFcaPhyDrvSeekErrs Counter, cpqFcaPhyDrvSpinupTime INTEGER, cpqFcaPhyDrvFunctTest1 Gauge, cpqFcaPhyDrvFunctTest2 Gauge, cpqFcaPhyDrvFunctTest3 Gauge, cpqFcaPhyDrvOtherTimeouts Counter, cpqFcaPhyDrvBadRecvReads Counter, cpqFcaPhyDrvBadRecvWrites Counter, cpqFcaPhyDrvFormatErrs Counter, cpqFcaPhyDrvNotReadyErrs Counter, cpqFcaPhyDrvHasMonInfo INTEGER, cpqFcaPhyDrvCondition INTEGER, cpqFcaPhyDrvHotPlugs Counter, cpqFcaPhyDrvMediaErrs Counter, cpqFcaPhyDrvHardwareErrs Counter, cpqFcaPhyDrvAbortedCmds Counter, cpqFcaPhyDrvSpinUpErrs Counter, cpqFcaPhyDrvBadTargetErrs Counter, cpqFcaPhyDrvSize INTEGER, cpqFcaPhyDrvBusFaults Counter, cpqFcaPhyDrvHotPlug INTEGER, cpqFcaPhyDrvPlacement INTEGER, cpqFcaPhyDrvBusNumber INTEGER, cpqFcaPhyDrvSerialNum DisplayString, cpqFcaPhyDrvPreFailMonitoring INTEGER, cpqFcaPhyDrvCurrentWidth INTEGER, cpqFcaPhyDrvCurrentSpeed INTEGER, cpqFcaPhyDrvFailureCode INTEGER, cpqFcaPhyDrvBlinkTime Counter, cpqFcaPhyDrvSmartStatus INTEGER } cpqFcaPhyDrvBoxIndex OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Fibre Channel Array Physical Drive Storage Box Index. The storage box index indicates which storage box this physical drive is in." ::= { cpqFcaPhyDrvEntry 1 } cpqFcaPhyDrvIndex OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Fibre Channel Array Physical Drive Index. This index is used for selecting the physical drive table entry. This number, along with the cpqFcaPhyDrvBoxIndex uniquely identify a specific physical drive." ::= { cpqFcaPhyDrvEntry 2 } cpqFcaPhyDrvModel OBJECT-TYPE SYNTAX DisplayString (SIZE (0..41)) ACCESS read-only STATUS mandatory DESCRIPTION "Fibre Channel Array Physical Drive Model. This is a text description of the physical drive. The text that appears depends upon who manufactured the drive and the drive type. For example, you might see: COMPAQ 210MB CP3201. If a drive fails, note the model to identify the type of drive necessary for replacement." ::= { cpqFcaPhyDrvEntry 3 } cpqFcaPhyDrvFWRev OBJECT-TYPE SYNTAX DisplayString (SIZE (0..8)) ACCESS read-only STATUS mandatory DESCRIPTION "Fibre Channel Array Physical Drive Firmware Revision. This shows the physical drive firmware revision number." ::= { cpqFcaPhyDrvEntry 4 } cpqFcaPhyDrvBay OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Fibre Channel Array Physical Drive Bay Location. This value matches the bay location where the physical drive has been installed. Each bay is labeled with a separate number so that you can identify the location of the drive." ::= { cpqFcaPhyDrvEntry 5 } cpqFcaPhyDrvStatus OBJECT-TYPE SYNTAX INTEGER { other(1), unconfigured(2), ok(3), threshExceeded(4), predictiveFailure(5), failed(6) } ACCESS read-only STATUS mandatory DESCRIPTION "Fibre Channel Array Physical Drive Status. This shows the status of the physical drive. The following values are valid for the physical drive status: other (1) Indicates that the instrument agent does not recognize the drive. You may need to upgrade your instrument agent and/or driver software. unconfigured (2) Indicates the drive is present, but is not part of any logical drive configuration. ok (3) Indicates the drive is functioning properly. thresholdExceeded (4) Indicates that the drive has a threshold exceeded error and should be replaced. predictiveFailure (5) Indicates that the drive has a predictive failure error and should be replaced. failed (6) Indicates that the drive is no longer operating and should be replaced." ::= { cpqFcaPhyDrvEntry 6 } cpqFcaPhyDrvUsedReallocs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Fibre Channel Array Physical Drive Used Reallocated Sectors. This shows the number of sectors of the reallocation area that have been used by the physical drive. To see how many sectors were originally available for use in the reallocation area, refer to the factory reallocation information if it exists. Not all drives support factory reallocation. Because of the nature of magnetic disks, certain sectors on a drive may have media defects. The reallocation area is part of the disk drive that the drive manufacturer sets aside to compensate for these defects. The drive array controller writes information addressed from these unusable sectors to available sectors in the reallocation area. If too many sectors have been reallocated, there may be a problem with the drive. If the value cannot be determined, 4,294,967,295 is returned." ::= { cpqFcaPhyDrvEntry 7 } cpqFcaPhyDrvRefHours OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Fibre Channel Array Reference Time in hours. This shows the total number of hours that a physical drive has been spinning since the drive was stamped. The drive will have either been stamped when it left the factory or when you ran Compaq Diagnostics on your new drive. You can use the reference time to calculate rates for other physical drive events." ::= { cpqFcaPhyDrvEntry 8 } cpqFcaPhyDrvHReads OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Fibre Channel Array Physical Drive Sectors Read (high). The phyDrvHReads and the phyDrvReads together shows the total number of sectors read from the physical disk drive during the reference time (phyDrvRefHours). The actual number of sectors read equals the phyDrvHReads times 2^32 plus the phyDrvReads. This information may be useful for determining rates. For instance, if you wanted to calculate the average number of reads per hour of operation, divide this number by the reference hours. If the value cannot be determined, 4,294,967,295 is returned." ::= { cpqFcaPhyDrvEntry 9 } cpqFcaPhyDrvReads OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Fibre Channel Array Physical Drive Sectors Read (low). The phyDrvHReads and the phyDrvReads together shows the total number of sectors read from the physical disk drive during the reference time (phyDrvRefHours). The actual number of sectors read equals the phyDrvHReads times 2^32 plus the phyDrvReads. This information may be useful for determining rates. For instance, if you wanted to calculate the average number of reads per hour of operation, divide this number by the reference hours. If the value cannot be determined, 4,294,967,295 is returned." ::= { cpqFcaPhyDrvEntry 10 } cpqFcaPhyDrvHWrites OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Sectors Written (high). The phyDrvHWrites and the phyDrvWrites together shows the total number of sectors written to the physical disk drive during the reference hours (phyDrvRefHours). The actual number of sectors written equals the phyDrvHWrites times 2^32 plus the phyDrvWrites. This information may be useful for determining rates. For instance, if you wanted to calculate the average number of writes per hour of operation, divide this number by the reference hours. If the value cannot be determined, 4,294,967,295 is returned." ::= { cpqFcaPhyDrvEntry 11 } cpqFcaPhyDrvWrites OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Sectors Written (low). The phyDrvHWrites and the phyDrvWrites together shows the total number of sectors written to the physical disk drive during the reference hours (phyDrvRefHours). The actual number of sectors written equals the phyDrvHWrites times 2^32 plus the phyDrvWrites. This information may be useful for determining rates. For instance, if you wanted to calculate the average number of writes per hour of operation, divide this number by the reference hours. If the value cannot be determined, 4,294,967,295 is returned." ::= { cpqFcaPhyDrvEntry 12 } cpqFcaPhyDrvHSeeks OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total Seeks (high). The phyDrvHSeeks and the phyDrvSeeks together shows the total number of seek operations performed by the physical disk drive during the reference hours (phyDrvRefHours). The actual number of seeks equals the phyDrvHSeeks times 2^32 plus the phyDrvWriteSeeks. If the value cannot be determined, 4,294,967,295 is returned." ::= { cpqFcaPhyDrvEntry 13 } cpqFcaPhyDrvSeeks OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total Seeks (low). The phyDrvHSeeks and the phyDrvSeeks together shows the total number of seek operations performed by the physical disk drive during the reference hours (phyDrvRefHours). The actual number of seeks equals the phyDrvHSeeks times 2^32 plus the phyDrvWriteSeeks. If the value cannot be determined, 4,294,967,295 is returned." ::= { cpqFcaPhyDrvEntry 14 } cpqFcaPhyDrvHardReadErrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Hard Read Errors. This shows the number of read errors that have occurred on a drive that could not be recovered by a physical drive's Error Correction Code (ECC) algorithm or through retries during the reference time (phyDrvRefTime). Over time, a disk drive may produce these errors. If you receive these errors, a problem may exist with your drive. The value increases every time the physical drive detects another error. The severity of these errors depends on whether the monitored system is running in a fault tolerant mode. With fault tolerance, the controller can remap data to eliminate the problems caused by these errors. In either case, if you see an increase in these errors, schedule server down time to run Compaq Diagnostics to verify that a problem exists. If the value cannot be determined, 4,294,967,295 is returned." ::= { cpqFcaPhyDrvEntry 15 } cpqFcaPhyDrvRecvReadErrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Recovered Read Errors. This shows the number of read errors corrected through physical drive retries during the reference time (phyDrvRefTime). Over time, all disk drives produce these errors. If you notice a rapid increase in the value for Recovered Read Errors (or Hard Read Errors), a problem may exist with the drive. The value increases every time the physical drive detects and corrects another error. Expect more Recovered Read Errors than Hard Read Errors. If you suspect that a problem may exist with the drive, schedule server down time to run Compaq Diagnostics. If the value cannot be determined, 4,294,967,295 is returned." ::= { cpqFcaPhyDrvEntry 16 } cpqFcaPhyDrvHardWriteErrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Hard Write Errors. This shows the number of write errors that could not be recovered by a physical drive during the reference time (phyDrvRefTime). Over time a disk drive may detect these errors. If you notice an increase in the value shown for Hard Write Errors or Recovered Write Errors, a problem may exist with the drive. The value increases every time the physical drive detects another error. On average, these errors should occur less frequently than read errors. If you see an increase in these errors, schedule server down time to run Compaq Diagnostics to verify that a problem exists. If the value cannot be determined, 4,294,967,295 is returned." ::= { cpqFcaPhyDrvEntry 17 } cpqFcaPhyDrvRecvWriteErrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Recovered Write Errors. This shows the number of write errors corrected through physical drive retries or recovered by a physical drive during the reference time (phyDrvRefTime). Over time a disk drive may produce these errors. If you notice an increase in the value shown for Hard Write Errors or Recovered Write Errors, a problem may exist with the drive. The value increases every time the physical drive detects and corrects an error. Only an unusually rapid increase in these errors indicates a problem. On average, these errors should occur less frequently than hard read errors. If you suspect that a problem may exist with the drive, schedule server down time to run Compaq Diagnostics. If the value cannot be determined, 4,294,967,295 is returned." ::= { cpqFcaPhyDrvEntry 18 } cpqFcaPhyDrvHSeekErrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Seek Errors (High). The phyDrvHSeekErrs and the phyDrvSeekErrs together shows the total number of times that the physical disk drive detected a seek error during the reference hours (phyDrvRefHours). The actual number of seek errors equals the phyDrvHSeekErrs times 2^32 plus the phyDrvWriteSeekErrs. Over time, a disk drive usually produces these errors. If you notice a rapid increase in the value shown for Seek Errors, this physical drive may be failing. The value increases every time the physical drive produces another error. Only an unusually rapid increase in these errors indicates a problem. If you suspect that a problem exists, schedule server down time to run Compaq Diagnostics. If the value cannot be determined, 4,294,967,295 is returned." ::= { cpqFcaPhyDrvEntry 19 } cpqFcaPhyDrvSeekErrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Seek Errors (low). The phyDrvHSeekErrs and the phyDrvSeekErrs together shows the total number of times that the physical disk drive detected a seek error during the reference hours (phyDrvRefHours). The actual number of seek errors equals the phyDrvHSeekErrs times 2^32 plus the phyDrvWriteSeekErrs. Over time, a disk drive usually produces these errors. If you notice a rapid increase in the value shown for Seek Errors, this physical drive may be failing. The value increases every time the physical drive produces another error. Only an unusually rapid increase in these errors indicates a problem. If you suspect that a problem exists, schedule server down time to run Compaq Diagnostics. If the value cannot be determined, 4,294,967,295 is returned." ::= { cpqFcaPhyDrvEntry 20 } cpqFcaPhyDrvSpinupTime OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Spin up Time in tenths of seconds. This is the time it takes for a physical drive to spin up to full speed. Disks require time to gain momentum and reach operating speed. As cars are tested to go from 0 mph to 60 mph in x number of seconds, drive manufacturers have preset expectations for the time it takes the drive to spin to full speed. Drives that do not meet these expectations may have problems. The value may be zero (0) under one of the following conditions: * If you are monitoring a physical drive that is part of the monitored system's internal drive array storage, and you use a warm boot to reset the monitored system. During a warm boot, the drives continue to spin. * If you have a Compaq Drive Array but have a version of the physical controller ROM that is less than version 1.00. If you have used an upgrade utility on versions less than 1.00, the value may still be zero. * If you are monitoring a physical drive in an Intelligent Array Expansion System and you reset the monitored system but not the Intelligent Array Expansion System. If you suspect a problem, schedule server down time to run Compaq Diagnostics and select the Drive Monitoring Diagnostics option to verify that a problem exists. If the value cannot be determined, -1 is returned." ::= { cpqFcaPhyDrvEntry 21 } cpqFcaPhyDrvFunctTest1 OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS deprecated DESCRIPTION "Functional Test 1. This provides information about a series of tests that indicate how well a physical drive works. These tests compare the way the physical drive currently operates when performing various tasks with the way it worked when it was new. A percent value is displayed that represents how the drive works currently when compared to how the drive worked when new. New drives operate at the 100 percent level. By default, if the current value is less than or equal to 80 percent, a problem may exist. If you suspect a problem, schedule server down time to run Compaq Diagnostics and select the Drive Monitoring Diagnostics option to verify that a problem exists. If the value cannot be determined, 4,294,967,295 is returned." ::= { cpqFcaPhyDrvEntry 22 } cpqFcaPhyDrvFunctTest2 OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS deprecated DESCRIPTION "Functional Test 2. This provides information about a series of tests that indicate how well a physical drive works. These tests compare the way the physical drive currently operates when performing various tasks with the way it worked when it was new. A percent value is displayed that represents how the drive works currently when compared to how the drive worked when new. New drives operate at the 100 percent level. By default, if the current value is less than or equal to 80 percent, a problem may exist. If you suspect a problem, schedule server down time to run Compaq Diagnostics and select the Drive Monitoring Diagnostics option to verify that a problem exists. If the value cannot be determined, 4,294,967,295 is returned." ::= { cpqFcaPhyDrvEntry 23 } cpqFcaPhyDrvFunctTest3 OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS deprecated DESCRIPTION "Functional Test 3. This provides information about a series of tests that indicate how well a physical drive works. These tests compare the way the physical drive currently operates when performing various tasks with the way it worked when it was new. A percent value is displayed that represents how the drive works currently when compared to how the drive worked when new. New drives operate at the 100 percent level. By default, if the current value is less than or equal to 80 percent, a problem may exist. If you suspect a problem, schedule server down time to run Compaq Diagnostics and select the Drive Monitoring Diagnostics option to verify that a problem exists. If the value cannot be determined, 4,294,967,295 is returned." ::= { cpqFcaPhyDrvEntry 24 } cpqFcaPhyDrvOtherTimeouts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Other Timeouts. The number of times that a physical drive did not respond with an interrupt within a controller-defined period of time after a command had been issued during the reference time (phyDrvRefTime). This does not include DRQ timeouts. If you suspect a problem, complete the following steps for the monitored system: 1. Check the cables connecting the drive to ensure that they are intact. 2. If the cables are properly connected, schedule server down time to run Compaq Diagnostics to verify that a problem exists. If the value cannot be determined, 4,294,967,295 is returned." ::= { cpqFcaPhyDrvEntry 25 } cpqFcaPhyDrvBadRecvReads OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Recovery Failed (Bad) Read Error. The number of times a read error occurred while performing Automatic Data Recovery from this physical drive to another drive during the reference time (phyDrvRefTime). If a read error occurs, Automatic Data Recovery stops. These errors indicate that the physical drive has failed. If you suspect a problem, schedule server down time to run Compaq Diagnostics and select the Drive Monitoring Diagnostics option to verify that a problem exists. If the value cannot be determined, 4,294,967,295 is returned." ::= { cpqFcaPhyDrvEntry 26 } cpqFcaPhyDrvBadRecvWrites OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Recovery Failed (Bad) Write Error. The number of times a write error occurred while performing Automatic Data Recovery from another drive to this physical drive during the reference time (phyDrvRefTime). If a write error occurs, Automatic Data Recovery stops. These errors indicate that the physical drive has failed. If you suspect a problem, schedule server down time to run Compaq Diagnostics and select the Drive Monitoring Diagnostics option to verify that a problem exists. If the value cannot be determined, 4,294,967,295 is returned." ::= { cpqFcaPhyDrvEntry 27 } cpqFcaPhyDrvFormatErrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Format Error. The number of times a format operation failed when the controller attempted to remap a bad sector during the reference time (phyDrvRefTime). Zero indicates that no format errors have occurred. The value increases each time a format error occurs. A failed format operation may cause the controller to mark a drive failed. If you suspect a problem, schedule server down time to run Compaq Diagnostics and select the Drive Monitoring Diagnostics option to verify a problem exists. If the value cannot be determined, 4,294,967,295 is returned." ::= { cpqFcaPhyDrvEntry 28 } cpqFcaPhyDrvNotReadyErrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Drive Not Ready Errors. The number of times the physical drive failed after the spin up command was issued during the reference time (phyDrvRefTime). When the spin up command was issued, the drive failed to reach its ready state. If the current value is zero, the drive has not failed. If the current value is greater than zero, at least one failure occurred. This error could be caused because the physical drive has failed to spin. If you suspect a problem: 1. Check the cables connecting the drive to ensure that they are intact. 2. If the cables are properly connected, schedule server down time to run Compaq Diagnostics to verify that a problem exists. If the value cannot be determined, 4,294,967,295 is returned." ::= { cpqFcaPhyDrvEntry 29 } cpqFcaPhyDrvHasMonInfo OBJECT-TYPE SYNTAX INTEGER { false(1), true(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Physical Drive Has Monitor Information. All of the physical disk table fields except for the physical disk status (phyDrvStatus) and the bay location (phyDrvBayLocation) are invalid unless this field has a value of true(2). If the value is false(1), you must run Compaq Diagnostics and select the Physical Drive Test option. This will enable the physical disk monitoring information." ::= { cpqFcaPhyDrvEntry 30 } cpqFcaPhyDrvCondition OBJECT-TYPE SYNTAX INTEGER { other(1), ok(2), degraded(3), failed(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The condition of the device. This value represents the overall condition of this physical drive." ::= { cpqFcaPhyDrvEntry 31 } cpqFcaPhyDrvHotPlugs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Physical Drive Hot Plug Count. This value indicates the number of times this physical drive was hot-plugged (removed) from a Compaq ProLiant Storage System. This is not supported by the IDA, IDA Expansion, or IDA-2 controllers. If the value cannot be determined, 4,294,967,295 is returned." ::= { cpqFcaPhyDrvEntry 32 } cpqFcaPhyDrvMediaErrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Physical Drive Media Failure Count. This value indicates the number of times this physical drive was failed due to unrecoverable media errors. If the value cannot be determined, 4,294,967,295 is returned." ::= { cpqFcaPhyDrvEntry 33 } cpqFcaPhyDrvHardwareErrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Physical Drive Hardware Error Count. This value indicates the number of times this physical drive returned a bad hardware status. The drive may be failed if retries do not work. If the value cannot be determined, 4,294,967,295 is returned." ::= { cpqFcaPhyDrvEntry 34 } cpqFcaPhyDrvAbortedCmds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Physical Drive Aborted Command Failures. This value indicates the number of times this physical drive was failed due to aborted commands that could not be retried successfully. If the value cannot be determined, 4,294,967,295 is returned." ::= { cpqFcaPhyDrvEntry 35 } cpqFcaPhyDrvSpinUpErrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Physical Drive Spin-Up Failure Count. This value indicates the number of times this physical drive was failed due to a failure of a spin-up command. If the value cannot be determined, 4,294,967,295 is returned." ::= { cpqFcaPhyDrvEntry 36 } cpqFcaPhyDrvBadTargetErrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Physical Drive Bad Target Count. This value indicates the number of times this physical drive performed some action that did not conform to the SCSI-2 bus protocol. These actions will cause the SCSI bus to be reset. If the value cannot be determined, 4,294,967,295 is returned." ::= { cpqFcaPhyDrvEntry 37 } cpqFcaPhyDrvSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Physical Drive Size in MB. This is the size of the physical drive in megabytes. This value is calculated using the value 1,048,576 (2^20) as a megabyte. Drive manufacturers sometimes use the number 1,000,000 as a megabyte when giving drive capacities so this value may differ from the advertised size of a drive." ::= { cpqFcaPhyDrvEntry 38 } cpqFcaPhyDrvBusFaults OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Physical Drive Bus Fault Count. This value indicates the number of times that a bus fault was detected for the drive by the controller. If the value cannot be determined, 4,294,967,295 is returned." ::= { cpqFcaPhyDrvEntry 39 } cpqFcaPhyDrvHotPlug OBJECT-TYPE SYNTAX INTEGER { other(1), hotPlug(2), nonHotPlug(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Physical Drive Hot Plug Support Status. The following values are defined: other(1) The Insight Agent is unable to determine if this drive supports hot plug replacement. hotPlug(2) The drive supports hot plug replacement. nonhotPlug(3) The drive does not support hot plug replacement." ::= { cpqFcaPhyDrvEntry 40 } cpqFcaPhyDrvPlacement OBJECT-TYPE SYNTAX INTEGER { other(1), internal(2), external(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Physical Drive Placement. The following values are defined: other(1) The agent is unable to determine if the drive is internal or external to the system chassis. internal(2) The drive is located in the system chassis. external(3) The drive is located outside the system chassis in an expansion box." ::= { cpqFcaPhyDrvEntry 41 } cpqFcaPhyDrvBusNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Physical Drive SCSI Bus Number. The bus number indicates to which SCSI bus this physical drive is attached. The first instance is one and increments for each SCSI bus on a controller." ::= { cpqFcaPhyDrvEntry 42 } cpqFcaPhyDrvSerialNum OBJECT-TYPE SYNTAX DisplayString (SIZE (0..40)) ACCESS read-only STATUS mandatory DESCRIPTION "Physical Drive Serial Number. This is the serial number assigned to the physical drive. This value is based upon the serial number as returned by the SCSI inquiry command but may have been modified due to space limitations. This can be used for identification purposes." ::= { cpqFcaPhyDrvEntry 43 } cpqFcaPhyDrvPreFailMonitoring OBJECT-TYPE SYNTAX INTEGER { other(1), notAvailable(2), available(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Drive Array Physical Drive Predictive Failure Monitoring. The following values are defined: other(1) The agent is unable to determine if the drive supports predictive failure monitoring. notAvailable(2) This drive does not support predictive failure monitoring. available(3) This drive supports predictive failure monitoring." ::= { cpqFcaPhyDrvEntry 44 } cpqFcaPhyDrvCurrentWidth OBJECT-TYPE SYNTAX INTEGER { other(1), narrow(2), wide16(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Physical Drive Current Width. The following values are defined: other(1) The agent is unable to determine the current negotiated data transfer width for this drive. narrow(2) The negotiated data transfer width for this drive is narrow (8 data bits). wide16(3) The negotiated data transfer width for this drive is wide (16 data bits)." ::= { cpqFcaPhyDrvEntry 45 } cpqFcaPhyDrvCurrentSpeed OBJECT-TYPE SYNTAX INTEGER { other(1), asynchronous(2), fast(3), ultra(4), ultra2(5), ultra3(6) } ACCESS read-only STATUS mandatory DESCRIPTION "Physical Drive Current Data Transfer Speed. The following values are defined: other(1) The agent is unable to determine the current negotiated data transfer speed for this drive. asynchronous(2) The negotiated data transfer speed for this drive is asynchronous. fast(3) The negotiated data transfer speed for this drive is 10 million transfers per second). ultra(4) The negotiated data transfer speed for this drive is 20 million transfers per second. ultra2(5) The negotiated data transfer speed for this drive is 40 million transfers per second. ultra3(6) The negotiated data transfer speed for this drive is 80 million transfers per second." ::= { cpqFcaPhyDrvEntry 46 } cpqFcaPhyDrvFailureCode OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Physical Drive Failure Code. This value is the drive failure reason code returned by the array firmware. It is valid only when the drive is failed. If the drive is not failed, 0 is returned." ::= { cpqFcaPhyDrvEntry 47 } cpqFcaPhyDrvBlinkTime OBJECT-TYPE SYNTAX Counter ACCESS read-write STATUS mandatory DESCRIPTION "Physical Drive LED Blink Time. This value is the amount of time remaining for the drive LEDs to blink in tenths of seconds. A value of zero means the drive LEDs are not blinking. If the value cannot be determined or the drive is not in a hot plug tray, 4,294,967,295 is returned. To blink the drive LEDs, set this value to the time to blink in tenths of seconds. To stop the drive LEDs from blinking, set this value to 0." ::= { cpqFcaPhyDrvEntry 48 } cpqFcaPhyDrvSmartStatus OBJECT-TYPE SYNTAX INTEGER { other(1), ok(2), replaceDrive(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Physical Drive S.M.A.R.T Status. The following values are defined: other(1) The agent is unable to determine if the status of S.M.A.R.T predictive failure monitoring for this drive. ok(2) Indicates the drive is functioning properly. replaceDrive(3) Indicates that the drive has a S.M.A.R.T predictive failure error and should be replaced." ::= { cpqFcaPhyDrvEntry 49 } -- **************************************************************************** -- Drive Array Physical Drive Threshold Table -- ========================================== -- -- The compaq enterprise (1.3.6.1.4.1.232) -- cpqFibreArray Group (1.3.6.1.4.1.232.16) -- cpqFcaComponent Group (1.3.6.1.4.1.232.16.2) -- cpqFcaPhyDrvThr Group (1.3.6.1.4.1.232.16.2.6) -- cpqFcaPhyDrvThrTable (1.3.6.1.4.1.232.16.2.6.1) -- -- **************************************************************************** cpqFcaPhyDrvThrTable OBJECT-TYPE SYNTAX SEQUENCE OF CpqFcaPhyDrvThrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Drive Array Physical Drive Threshold Table. A table of physical drive threshold entries." ::= { cpqFcaPhyDrvThr 1 } cpqFcaPhyDrvThrEntry OBJECT-TYPE SYNTAX CpqFcaPhyDrvThrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Drive Array Physical Drive Threshold Entry. A physical drive threshold entry." INDEX { cpqFcaPhyDrvThrBoxIndex, cpqFcaPhyDrvThrIndex } ::= { cpqFcaPhyDrvThrTable 1 } CpqFcaPhyDrvThrEntry ::= SEQUENCE { cpqFcaPhyDrvThrBoxIndex INTEGER, cpqFcaPhyDrvThrIndex INTEGER, cpqFcaPhyDrvThrUsedReallocs INTEGER, cpqFcaPhyDrvThrSpinupTime INTEGER, cpqFcaPhyDrvThrFunctTest1 INTEGER, cpqFcaPhyDrvThrFunctTest2 INTEGER, cpqFcaPhyDrvThrFunctTest3 INTEGER, cpqFcaPhyDrvThrViUsedReallocs INTEGER, cpqFcaPhyDrvThrViSpinupTime INTEGER, cpqFcaPhyDrvThrViFunctTest1 INTEGER, cpqFcaPhyDrvThrViFunctTest2 INTEGER, cpqFcaPhyDrvThrViFunctTest3 INTEGER } cpqFcaPhyDrvThrBoxIndex OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Fibre Channel Array Physical Drive Threshold Storage Box Index. The storage box index indicates which storage box this physical drive is in." ::= { cpqFcaPhyDrvThrEntry 1 } cpqFcaPhyDrvThrIndex OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Drive Array Physical Drive Threshold Index. This index maps the thresholds to a physical drive. The value of this index is the same as the one used with the physical drive table." ::= { cpqFcaPhyDrvThrEntry 2 } cpqFcaPhyDrvThrUsedReallocs OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Used Reallocated Sectors Maximum Threshold. This shows the maximum threshold of the reallocation area that has been used by the physical drive. This threshold is associated with the cpqFcaPhyDrvUsedReallocs object in the Physical Drive Table. If the value cannot be determined, -1 is returned." ::= { cpqFcaPhyDrvThrEntry 3 } cpqFcaPhyDrvThrSpinupTime OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Spin up Time Maximum Threshold in tenths of seconds. This shows the maximum of time it takes for a physical drive to spin up to full speed. This threshold is associated with the cpqFcaPhyDrvSpinupTime object in the Physical Drive Table. If the value cannot be determined, -1 is returned." ::= { cpqFcaPhyDrvThrEntry 4 } cpqFcaPhyDrvThrFunctTest1 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS deprecated DESCRIPTION "Functional Test 1 Minimum Threshold. This provides the minimum threshold for information about a series of tests that indicate how well a physical drive works. These tests compare the way the physical drive currently operate when performing various tasks with the way it worked when it was new. This threshold is associated with the cpqFcaPhyDrvFunctTest1 object in the Physical Drive Table. If the value cannot be determined, -1 is returned." ::= { cpqFcaPhyDrvThrEntry 5 } cpqFcaPhyDrvThrFunctTest2 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS deprecated DESCRIPTION "Functional Test 2 Minimum Threshold. This provides the minimum threshold for information about a series of tests that indicate how well a physical drive works. These tests compare the way the physical drive currently operates when performing various tasks with the way it worked when it was new. This threshold is associated with the cpqFcaPhyDrvFunctTest2 object in the Physical Drive Table. If the value cannot be determined, -1 is returned." ::= { cpqFcaPhyDrvThrEntry 6 } cpqFcaPhyDrvThrFunctTest3 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS deprecated DESCRIPTION "Functional Test 3 Minimum Threshold. This provides the minimum threshold for information about a series of tests that indicate how well a physical drive works. These tests compare the way the physical drive currently operates when performing various tasks with the way it worked when it was new. This threshold is associated with the cpqFcaPhyDrvFunctTest3 object in the Physical Drive Table. If the value cannot be determined, -1 is returned." ::= { cpqFcaPhyDrvThrEntry 7 } cpqFcaPhyDrvThrViUsedReallocs OBJECT-TYPE SYNTAX INTEGER { false(1), true(2), unknown(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Used Reallocated Sectors Threshold Has Been Violated. This is used to indicate whether the number of used sectors of the reallocation area for a physical drive has ever exceeded the maximum allowable threshold. The valid values are: false (1) Indicates that the Used Reallocated Sectors object (cpqFcaPhyDrvUsedReallocs) value has not exceeded the maximum threshold (cpqFcaPhyDrvThrUsedReallocs). true (2) Indicates that the Used Reallocated Sectors object (cpqFcaPhyDrvUsedReallocs) value has exceeded the maximum threshold (cpqFcaPhyDrvThrUsedReallocs). unknown (3) The agent is unable to determine if the drive has a threshold violation." ::= { cpqFcaPhyDrvThrEntry 8 } cpqFcaPhyDrvThrViSpinupTime OBJECT-TYPE SYNTAX INTEGER { false(1), true(2), unknown(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Spin up Time in tenths of seconds Threshold Has Been Violated. This is used to indicate whether the time it took for a physical drive to spin up to full speed has ever exceeded the maximum allowable threshold. The valid values are: false (1) Indicates that the Spin up Time object (cpqFcaPhyDrvSpinupTime) value has not exceeded the maximum threshold (cpqFcaPhyDrvThrSpinupTime). true (2) Indicates that the Spin up Time object (cpqFcaPhyDrvSpinupTime) value has exceeded the maximum threshold (cpqFcaPhyDrvThrSpinupTime). unknown (3) The agent is unable to determine if the drive has a threshold violation." ::= { cpqFcaPhyDrvThrEntry 9 } cpqFcaPhyDrvThrViFunctTest1 OBJECT-TYPE SYNTAX INTEGER { false(1), true(2), unknown(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Functional Test 1 Threshold Has Been Violated. This is used to indicate whether the percentage value returned from Functional Test 1 has every dropped below the allowable threshold for that test. The valid values are: false (1) Indicates that the Functional Test 1 object (cpqFcaPhyDrvFunctTest1) value has not fallen below the minimum threshold (cpqFcaPhyDrvThrFunctTest1). true (2) Indicates that the Functional Test 1 object (cpqFcaPhyDrvFunctTest1) value has fallen below the minimum threshold (cpqFcaPhyDrvThrFunctTest1). unknown (3) The agent is unable to determine if the drive has a threshold violation." ::= { cpqFcaPhyDrvThrEntry 10 } cpqFcaPhyDrvThrViFunctTest2 OBJECT-TYPE SYNTAX INTEGER { false(1), true(2), unknown(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Functional Test 2 Threshold Has Been Violated. This is used to indicate whether the percentage value returned from Functional Test 2 has every dropped below the allowable threshold for that test. The valid values are: false (1) Indicates that the Functional Test 2 object (cpqFcaPhyDrvFunctTest2) value has not fallen below the minimum threshold (cpqFcaPhyDrvThrFunctTest2). true (2) Indicates that the Functional Test 2 object (cpqFcaPhyDrvFunctTest2) value has fallen below the minimum threshold (cpqFcaPhyDrvThrFunctTest2). unknown (3) The agent is unable to determine if the drive has a threshold violation." ::= { cpqFcaPhyDrvThrEntry 11 } cpqFcaPhyDrvThrViFunctTest3 OBJECT-TYPE SYNTAX INTEGER { false(1), true(2), unknown(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Functional Test 3 Threshold Has Been Violated. This is used to indicate whether the percentage value returned from Functional Test 3 has every dropped below the allowable threshold for that test. The valid values are: false (1) Indicates that the Functional Test 3 object (cpqFcaPhyDrvFunctTest3) value has not fallen below the minimum threshold (cpqFcaPhyDrvThrFunctTest3). true (2) Indicates that the Functional Test 3 object (cpqFcaPhyDrvFunctTest3) value has fallen below the minimum threshold (cpqFcaPhyDrvThrFunctTest3). unknown (3) The agent is unable to determine if the drive has a threshold violation." ::= { cpqFcaPhyDrvThrEntry 12 } -- **************************************************************************** -- Fibre Channel Host Controller Group -- =================================== -- -- The compaq enterprise (1.3.6.1.4.1.232) -- cpqFibreArray Group (1.3.6.1.4.1.232.16) -- cpqFcaComponent Group (1.3.6.1.4.1.232.16.2) -- cpqFcaHostCntlr Group (1.3.6.1.4.1.232.16.2.7) -- cpqFcaHostCntlrTable (1.3.6.1.4.1.232.16.2.7.1) -- -- The Host Controller group contains the configuration and statistical -- information of the Fibre Channel Host Controller. -- -- Implementation of the cpqFcaHostCntlr group is mandatory for all -- agents that support the Compaq Fibre Channel MIB. -- -- **************************************************************************** cpqFcaHostCntlrTable OBJECT-TYPE SYNTAX SEQUENCE OF CpqFcaHostCntlrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Compaq Fibre Channel Host Controller Table." ::= { cpqFcaHostCntlr 1 } cpqFcaHostCntlrEntry OBJECT-TYPE SYNTAX CpqFcaHostCntlrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Compaq Array Controller Entry." INDEX { cpqFcaHostCntlrIndex } ::= { cpqFcaHostCntlrTable 1 } CpqFcaHostCntlrEntry ::= SEQUENCE { cpqFcaHostCntlrIndex INTEGER, cpqFcaHostCntlrSlot INTEGER, cpqFcaHostCntlrModel INTEGER, cpqFcaHostCntlrStatus INTEGER, cpqFcaHostCntlrCondition INTEGER, cpqFcaHostCntlrWorldWideName DisplayString, cpqFcaHostCntlrStorBoxList OCTET STRING, cpqFcaHostCntlrOverallCondition INTEGER, cpqFcaHostCntlrTapeCntlrList OCTET STRING, cpqFcaHostCntlrSerialNumber DisplayString, cpqFcaHostCntlrHwLocation DisplayString } cpqFcaHostCntlrIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Host Controller Index. This value is a logical number whose meaning is OS dependent. Each physical controller has one unique controller number associated with it." ::= { cpqFcaHostCntlrEntry 1 } cpqFcaHostCntlrSlot OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Host Controller Slot. This identifies the physical slot where the Compaq Fibre Channel Host Controller resides in the system. For example, if this value is three, the controller is located in slot three of your computer. If the slot cannot be determined, the value is set to 255." ::= { cpqFcaHostCntlrEntry 2 } cpqFcaHostCntlrModel OBJECT-TYPE SYNTAX INTEGER { other(1), fchc-p(2), fchc-e(3), fchc64(4), sa-sam(5), fca-2101(6) } ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Host Controller Model. The type of controller card. The valid types are: Other (1) You may need to upgrade your driver software and\or instrument agent(s). You have a drive array controller in the system that the instrument agent does not recognize. fchc-p (2) Compaq StorageWorks Fibre Channel Host Bus Adapter/P. fchc-e (3) Compaq StorageWorks Fibre Channel Host Bus Adapter/E. fchc64 (4) Compaq StorageWorks 64-Bit/66-Mhz Fibre Host Bus Adapter. sa-sam(5) Compaq Smart Array, SAN Access Module. fca-2101(6) FCA-2101" ::= { cpqFcaHostCntlrEntry 3 } cpqFcaHostCntlrStatus OBJECT-TYPE SYNTAX INTEGER { other(1), ok(2), failed(3), shutdown(4), loopDegraded(5), loopFailed(6) } ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Host Controller Status. The host controller can be in one of the following states: Other (1) The agent is unable to determine the status of the host controller. Ok (2) Indicates that the host controller is in normal operation mode. Failed (3) Indicates that the host controller has failed and should be replaced. Shutdown (4) Indicates that the host controller has been shutdown. LoopDegraded (5) Indicates that the fibre channel connection is degraded. LoopFailed (6) Indicates that the fibre channel connection is failed." ::= { cpqFcaHostCntlrEntry 4 } cpqFcaHostCntlrCondition OBJECT-TYPE SYNTAX INTEGER { other(1), ok(2), degraded(3), failed(4) } ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Host Controller Condition. This value represents the condition of this controller." ::= { cpqFcaHostCntlrEntry 5 } cpqFcaHostCntlrWorldWideName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..16)) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Host Controller World Wide Name. This value can be used to further identify a particular controller. If the world wide name is not supported, the agent will return a NULL string." ::= { cpqFcaHostCntlrEntry 6 } cpqFcaHostCntlrStorBoxList OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Host Controller Storage Box List. This lists the storage boxes which are associated with this host controller. These are the same IDs which can be used as indices into the storage box table. Each 2 bytes of the string is an index." ::= { cpqFcaHostCntlrEntry 7} cpqFcaHostCntlrOverallCondition OBJECT-TYPE SYNTAX INTEGER { other(1), ok(2), degraded(3), failed(4) } ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Host Controller Overall Condition. This value represents the overall condition of this controller, and any associated storage boxes." ::= { cpqFcaHostCntlrEntry 8 } cpqFcaHostCntlrTapeCntlrList OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Host Controller Tape Controller List. This lists the tape controllers which are associated with this host controller. These are the same IDs which can be used as indices into the tape controller table. Each 2 bytes of the string is an index." ::= { cpqFcaHostCntlrEntry 9} cpqFcaHostCntlrSerialNumber OBJECT-TYPE SYNTAX DisplayString (SIZE (0..128)) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Host Controller Serial Number. This value can be used to further identify a particular controller. If the serial number is not supported, the agent will return a NULL string." ::= { cpqFcaHostCntlrEntry 10 } cpqFcaHostCntlrHwLocation OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) ACCESS read-only STATUS optional DESCRIPTION "A text description of the hardware location, on complex multi SBB hardware only, for the controller. A NULL string indicates that the hardware location could not be determined or is irrelevant." ::= { cpqFcaHostCntlrEntry 11 } -- **************************************************************************** -- Fibre Channel Tape Controller Group -- =================================== -- -- The compaq enterprise (1.3.6.1.4.1.232) -- cpqFibreArray Group (1.3.6.1.4.1.232.16) -- cpqFcTapeComponent Group (1.3.6.1.4.1.232.16.3) -- cpqFcTapeCntlr Group (1.3.6.1.4.1.232.16.3.1) -- cpqFcTapeCntlrTable (1.3.6.1.4.1.232.16.3.1.1) -- -- The tape controller group contains the configuration and statistical -- information of the Fibre Channel Tape Controller. -- -- Implementation of the cpqFcTapeCntlr group is mandatory for all -- agents that support the Compaq Fibre Channel MIB. -- -- **************************************************************************** cpqFcTapeCntlrTable OBJECT-TYPE SYNTAX SEQUENCE OF CpqFcTapeCntlrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Controller Table." ::= { cpqFcTapeCntlr 1 } cpqFcTapeCntlrEntry OBJECT-TYPE SYNTAX CpqFcTapeCntlrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Controller Entry." INDEX { cpqFcTapeCntlrIndex } ::= { cpqFcTapeCntlrTable 1 } CpqFcTapeCntlrEntry ::= SEQUENCE { cpqFcTapeCntlrIndex INTEGER, cpqFcTapeCntlrStatus INTEGER, cpqFcTapeCntlrCondition INTEGER, cpqFcTapeCntlrOverallCondition INTEGER, cpqFcTapeCntlrWWN DisplayString, cpqFcTapeCntlrFWRev DisplayString, cpqFcTapeCntlrType INTEGER } cpqFcTapeCntlrIndex OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Controller Index. This value is a logical number whose meaning is OS dependent. Each tape controller has one unique controller number associated with it." ::= { cpqFcTapeCntlrEntry 1 } cpqFcTapeCntlrStatus OBJECT-TYPE SYNTAX INTEGER { other(1), ok(2), offline(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Controller Status. The following values are defined: other(1) The agent is unable to determine the status of the tape controller. ok(2) The tape controller is OK. offline(3) The tape controller is offline. The tape controller may be powered off or there may be a cabling problem." ::= { cpqFcTapeCntlrEntry 2 } cpqFcTapeCntlrCondition OBJECT-TYPE SYNTAX INTEGER { other(1), ok(2), degraded(3), failed(4) } ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Controller Condition. This value represents the condition of the tape controller." ::= { cpqFcTapeCntlrEntry 3 } cpqFcTapeCntlrOverallCondition OBJECT-TYPE SYNTAX INTEGER { other(1), ok(2), degraded(3), failed(4) } ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Controller Index. This value represents the overall condition of the tape controller and any associated tape libraries." ::= { cpqFcTapeCntlrEntry 4 } cpqFcTapeCntlrWWN OBJECT-TYPE SYNTAX DisplayString (SIZE (0..16)) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Controller World Wide Name. This value can be used to further identify a particular tape controller. If the world wide name is not supported, the agent will return a NULL string." ::= { cpqFcTapeCntlrEntry 5 } cpqFcTapeCntlrFWRev OBJECT-TYPE SYNTAX DisplayString (SIZE (0..8)) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Controller Firmware Revision. This shows the tape controller firmware revision number. If the world wide name is not supported, the agent will return a NULL string." ::= { cpqFcTapeCntlrEntry 6 } cpqFcTapeCntlrType OBJECT-TYPE SYNTAX INTEGER { other(1), fiberTape(2), modularDataRouter(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Controller Type. The following values are defined: other(1) The agent is unable to determine if the type of the tape controller. fiberTape(2) The original Fibre Channel Tape Controller. modularDataRouter(3) The Compaq Modular Data Router." ::= { cpqFcTapeCntlrEntry 7 } -- **************************************************************************** -- Fibre Channel Tape Library Group -- ================================ -- -- The compaq enterprise (1.3.6.1.4.1.232) -- cpqFibreArray Group (1.3.6.1.4.1.232.16) -- cpqFcTapeComponent Group (1.3.6.1.4.1.232.16.3) -- cpqFcTapeLibrary Group (1.3.6.1.4.1.232.16.3.2) -- cpqFcTapelibraryTable (1.3.6.1.4.1.232.16.3.2.1) -- -- The tape library group contains the configuration and statistical -- information of the Compaq Fibre Channel Tape Library. -- -- Implementation of the cpqFcTapeLibrary group is mandatory for all -- agents that support the Compaq Fibre Channel MIB. -- -- **************************************************************************** cpqFcTapeLibraryTable OBJECT-TYPE SYNTAX SEQUENCE OF CpqFcTapeLibraryEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Library Table." ::= { cpqFcTapeLibrary 1 } cpqFcTapeLibraryEntry OBJECT-TYPE SYNTAX CpqFcTapeLibraryEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Library Entry." INDEX { cpqFcTapeLibraryCntlrIndex, cpqFcTapeLibraryScsiBus, cpqFcTapeLibraryScsiTarget, cpqFcTapeLibraryScsiLun } ::= { cpqFcTapeLibraryTable 1 } CpqFcTapeLibraryEntry ::= SEQUENCE { cpqFcTapeLibraryCntlrIndex INTEGER, cpqFcTapeLibraryScsiBus INTEGER, cpqFcTapeLibraryScsiTarget INTEGER, cpqFcTapeLibraryScsiLun INTEGER, cpqFcTapeLibrarySerialNumber DisplayString, cpqFcTapeLibraryModel DisplayString, cpqFcTapeLibraryFWRev DisplayString, cpqFcTapeLibraryStatus INTEGER, cpqFcTapeLibraryDoorStatus INTEGER, cpqFcTapeLibraryCondition INTEGER, cpqFcTapeLibraryOverallCondition INTEGER, cpqFcTapeLibraryLastError INTEGER, cpqFcTapeLibraryStatHours Counter, cpqFcTapeLibraryStatMoves Counter, cpqFcTapeLibraryDriveList OCTET STRING } cpqFcTapeLibraryCntlrIndex OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Library Controller Index. This value is a logical number whose meaning is OS dependent. Each tape controller has one unique controller number associated with it." ::= { cpqFcTapeLibraryEntry 1 } cpqFcTapeLibraryScsiBus OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Library Scsi Bus. The bus index indicates to which SCSI bus instance on a tape controller this table entry belongs." ::= { cpqFcTapeLibraryEntry 2 } cpqFcTapeLibraryScsiTarget OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Library Scsi Target. The target index indicates to which SCSI ID on a tape controller SCSI bus this table entry belongs." ::= { cpqFcTapeLibraryEntry 3 } cpqFcTapeLibraryScsiLun OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Library Scsi Lun. The Lun index indicates to which logical unit on a SCSI ID on a tape controller SCSI bus this table entry belongs." ::= { cpqFcTapeLibraryEntry 4 } cpqFcTapeLibrarySerialNumber OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Library Serial Number. This is the unit serial number for the tape library. It can be used for identification purposes." ::= { cpqFcTapeLibraryEntry 5 } cpqFcTapeLibraryModel OBJECT-TYPE SYNTAX DisplayString (SIZE (0..128)) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Library Model. This is the model name of the tape library. It can be used for identification purposes." ::= { cpqFcTapeLibraryEntry 6 } cpqFcTapeLibraryFWRev OBJECT-TYPE SYNTAX DisplayString (SIZE (0..8)) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Library Serial Number. This is firmware revision level of the tape library. It can be used for identification purposes." ::= { cpqFcTapeLibraryEntry 7 } cpqFcTapeLibraryStatus OBJECT-TYPE SYNTAX INTEGER { other(1), ok(2), degraded(3), failed(4), offline(5) } ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Library Status. The library can be in one of the following states: other(1) The library is in a state other than one of those listed below. ok(2) Indicates that the library is in normal operation mode. No user action is necessary. degraded(3) Indicates that the library has degraded in some manner. failed(4) Indicates that the library has failed and can no longer return data. The library may need to be replaced. offline(5) Indicates that the Insight Agents can no longer communicate with the library. This could be caused by a cabling problem or the library may be powered off." ::= { cpqFcTapeLibraryEntry 8 } cpqFcTapeLibraryDoorStatus OBJECT-TYPE SYNTAX INTEGER { other(1), notSupported(2), closed(3), open(4) } ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Library Door Status. The door can be in one of the following states: other(1) The door is in a state other than one of those listed below. notSupported(2) The door status is not supported by the device. closed(3) The door is closed. open(4) The door is open." ::= { cpqFcTapeLibraryEntry 9 } cpqFcTapeLibraryCondition OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Library Condition. This value represents the overall condition of the tape library." ::= { cpqFcTapeLibraryEntry 10 } cpqFcTapeLibraryOverallCondition OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Library Overall Condition. This value represents the overall condition of the tape library and any associated tape drives." ::= { cpqFcTapeLibraryEntry 11 } cpqFcTapeLibraryLastError OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Library Last Error. This is the last error returned by the tape library." ::= { cpqFcTapeLibraryEntry 12 } cpqFcTapeLibraryStatHours OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Library Stat Hours. This is the number of hours of operation for the library." ::= { cpqFcTapeLibraryEntry 13 } cpqFcTapeLibraryStatMoves OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Library Stat Moves. This is the number of tape moves for the library loader arm." ::= { cpqFcTapeLibraryEntry 14 } cpqFcTapeLibraryDriveList OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..60)) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Library Tape Drive List. This is a data structure containing the list of tape drive ids that are present in this library. The format is: field octets contents ===== ====== ======== 1 1-2 Tape controller index 2 3 Tape drive SCSI bus 3 4 Tape drive SCSI target 4 5 Tape drive SCSI logical unit number These 5 octets are repeated for each drive in the library. For n tape drives in a library, the string is 5 * n octets long." ::= { cpqFcTapeLibraryEntry 15 } -- **************************************************************************** -- Fibre Channel Tape Drive Group -- ============================== -- -- The compaq enterprise (1.3.6.1.4.1.232) -- cpqFibreArray Group (1.3.6.1.4.1.232.16) -- cpqFcTapeComponent Group (1.3.6.1.4.1.232.16.3) -- cpqFcTapeDrive Group (1.3.6.1.4.1.232.16.3.3) -- cpqFcTapeDriveTable (1.3.6.1.4.1.232.16.3.3.1) -- -- The tape drive group contains the configuration and statistical -- information of the Compaq Fibre Channel Physical Tape Drive. -- -- Implementation of the cpqFcTapeDrive group is mandatory for all -- agents that support the Compaq Fibre Channel MIB. -- -- **************************************************************************** cpqFcTapeDriveTable OBJECT-TYPE SYNTAX SEQUENCE OF CpqFcTapeDriveEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Drive Table." ::= { cpqFcTapeDrive 1 } cpqFcTapeDriveEntry OBJECT-TYPE SYNTAX CpqFcTapeDriveEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Drive Entry." INDEX { cpqFcTapeDriveCntlrIndex, cpqFcTapeDriveScsiBus, cpqFcTapeDriveScsiTarget, cpqFcTapeDriveScsiLun } ::= { cpqFcTapeDriveTable 1 } CpqFcTapeDriveEntry ::= SEQUENCE { cpqFcTapeDriveCntlrIndex INTEGER, cpqFcTapeDriveScsiBus INTEGER, cpqFcTapeDriveScsiTarget INTEGER, cpqFcTapeDriveScsiLun INTEGER, cpqFcTapeDriveSerialNumber DisplayString, cpqFcTapeDriveModel DisplayString, cpqFcTapeDriveFWRev DisplayString, cpqFcTapeDriveType INTEGER, cpqFcTapeDriveFWSubtype INTEGER, cpqFcTapeDriveStatus INTEGER, cpqFcTapeDriveCleanReq INTEGER, cpqFcTapeDriveCleanTapeRepl INTEGER, cpqFcTapeDriveCondition INTEGER, cpqFcTapeDriveCleanTapeCount INTEGER, cpqFcTapeDriveLibraryDrive INTEGER, cpqFcTapeDriveLocation DisplayString, cpqFcTapeDriveHotPlug INTEGER } cpqFcTapeDriveCntlrIndex OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq External Tape Drive Controller Index. This value is a logical number whose meaning is OS dependent. For tape controller has one unique controller number associated with it." ::= { cpqFcTapeDriveEntry 1 } cpqFcTapeDriveScsiBus OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq External Tape Drive Scsi Bus. The bus index indicates to which SCSI bus instance on a tape controller this table entry belongs." ::= { cpqFcTapeDriveEntry 2 } cpqFcTapeDriveScsiTarget OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq External Tape Drive Scsi Target. The target index indicates to which SCSI ID on a tape controller SCSI bus this table entry belongs." ::= { cpqFcTapeDriveEntry 3 } cpqFcTapeDriveScsiLun OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq External Tape Drive Scsi Lun. The Lun index indicates to which logical unit on a SCSI ID on a tape controller SCSI bus this table entry belongs." ::= { cpqFcTapeDriveEntry 4 } cpqFcTapeDriveSerialNumber OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq External Tape Drive Serial Number. This is the unit serial number for the tape drive. It can be used for identification purposes." ::= { cpqFcTapeDriveEntry 5 } cpqFcTapeDriveModel OBJECT-TYPE SYNTAX DisplayString (SIZE (0..128)) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq External Tape Drive Model. This is the model name of the tape drive. It can be used for identification purposes." ::= { cpqFcTapeDriveEntry 6 } cpqFcTapeDriveFWRev OBJECT-TYPE SYNTAX DisplayString (SIZE (0..8)) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq External Tape Drive Firmware Revision. This is firmware revision level of the tape drive. It can be used for identification purposes." ::= { cpqFcTapeDriveEntry 7 } cpqFcTapeDriveType OBJECT-TYPE SYNTAX INTEGER { other(1), cpqDlt35-70(2) } ACCESS read-only STATUS deprecated DESCRIPTION "Compaq External Tape Drive Type. This is the drive type. It can be used for identification purposes. The following values are defined: other(1) The management agent does not recognize this model. You may need to upgrade your software. cpqDlt35-70(2) Compaq 35/70-Gigabyte DLT Tape Drive." ::= { cpqFcTapeDriveEntry 8 } cpqFcTapeDriveFWSubtype OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq External Tape Drive Firmware Subtype. This is used to differentiate the firmware versions which have the same tape drive type (as specified by cpqFcTapeDriveType). Tape drives will contain a value of 1 for this variable when they first ship, and this value will be incremented if future versions are shipped which are not firmware compatible with the predecessor. If the tape drive does not support this capability, a value of 0 will be returned." ::= { cpqFcTapeDriveEntry 9 } cpqFcTapeDriveStatus OBJECT-TYPE SYNTAX INTEGER { other(1), ok(2), degraded(3), failed(4), offline(5), missingWasOk(6), missingWasOffline(7) } ACCESS read-only STATUS mandatory DESCRIPTION "Compaq External Tape Drive Status. The tape drive can be in one of the following states: other(1) The tape drive is in a state other than one of those listed below. ok(2) Indicates that the tape drive is in normal operation mode. No user action is necessary. degraded(3) Indicates that the tape drive has degraded in some manner. failed(4) Indicates that the tape drive has failed and can no longer return data. The tape drive may need to be replaced. offline(5) Indicates that the agent can no longer communicate with the tape drive. This could be caused by a cabling problem or the tape drive may be powered off. missingWasOk(6) Indicates that a tape drive had a status of OK and is no longer present. The drive has been removed. missingWasOffline(7) Indicates that a tape drive had a status of OFFLINE and is no longer present. The drive has been removed." ::= { cpqFcTapeDriveEntry 10 } cpqFcTapeDriveCleanReq OBJECT-TYPE SYNTAX INTEGER { other(1), true(2), false(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Compaq External Tape Drive Cleaning Required. This is an indication of whether the tape drive heads require a cleaning session to occur. If this variable indicates a need to clean the tape heads, then a cleaning tape will need to be inserted and run through a cleaning cycle. This variable can be in one of the following states: other(1) The tape drive does not support monitoring of the cleaning required status. true(2) The tape drive requires a cleaning tape session in order to clean the heads. false(3) The tape drive does not require any cleaning tape session." ::= { cpqFcTapeDriveEntry 11 } cpqFcTapeDriveCleanTapeRepl OBJECT-TYPE SYNTAX INTEGER { other(1), true(2), false(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Compaq External Tape Drive Cleaning Tape Replacement. This variable is only applicable to autoloader tape drives. This variable indicates whether the cleaning tape which is inserted in an autoloader needs to be replaced because its cleaning capability is exhausted (it is at end of tape). This variable can be in one of the following states: other(1) The tape drive does not support monitoring of the cleaning tape replacement status. true(2) The autoloader tape drive requires a new cleaning tape to be inserted. false(3) The tape drive does not require a new cleaning tape." ::= { cpqFcTapeDriveEntry 12 } cpqFcTapeDriveCondition OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Compaq External Tape Drive Condition. This value represents the overall condition of the tape drive." ::= { cpqFcTapeDriveEntry 13 } cpqFcTapeDriveCleanTapeCount OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Compaq External Tape Drive Cleaning Tape Count. This variable is a count from a tape drive of the number of cleanings done by the tape cleaner last in the drive." ::= { cpqFcTapeDriveEntry 14 } cpqFcTapeDriveLibraryDrive OBJECT-TYPE SYNTAX INTEGER { other(1), true(2), false(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Compaq External Tape Drive Library Drive. This variable indicates whether or not the tape drive is part of a tape library. It can be in one of the following states: other(1) Indicates that the storage agent cannot determine if the tape drive is part of a tape library. true(2) The tape drive is part of a tape library. false(3) The tape drive is not part of a tape library." ::= { cpqFcTapeDriveEntry 15 } cpqFcTapeDriveLocation OBJECT-TYPE SYNTAX DisplayString (SIZE (0..128)) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq External Tape Drive Location. This is the location of the tape drive." ::= { cpqFcTapeDriveEntry 16 } cpqFcTapeDriveHotPlug OBJECT-TYPE SYNTAX INTEGER { other(1), hotPlug(2), nonHotPlug(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Compaq External Tape Drive Hot Plug Support Status. The following values are defined: other(1) The agent is unable to determine if this drive supports hot plug replacement. hotPlug(2) The drive supports hot plug replacement. nonhotPlug(3) The drive does not support hot plug replacement." ::= { cpqFcTapeDriveEntry 17 } -- **************************************************************************** -- Fibre Channel Tape Counters Group -- ================================ -- -- The compaq enterprise (1.3.6.1.4.1.232) -- cpqFibreArray Group (1.3.6.1.4.1.232.16) -- cpqFcTapeComponent Group (1.3.6.1.4.1.232.16.3) -- cpqFcTapeCounters Group (1.3.6.1.4.1.232.16.3.4) -- cpqFcTapeCountersTable (1.3.6.1.4.1.232.16.3.4.1) -- -- The tape counters group contains the statistical information of -- the Compaq Fibre Channel Tape Drives. -- -- Implementation of the cpqFcTapeCounters group is mandatory for all -- agents that support the Compaq Fibre Channel MIB. -- -- **************************************************************************** cpqFcTapeCountersTable OBJECT-TYPE SYNTAX SEQUENCE OF CpqFcTapeCountersEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Counters Table." ::= { cpqFcTapeCounters 1 } cpqFcTapeCountersEntry OBJECT-TYPE SYNTAX CpqFcTapeCountersEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Counters Entry." INDEX { cpqFcTapeCountersCntlrIndex, cpqFcTapeCountersScsiBus, cpqFcTapeCountersScsiTarget, cpqFcTapeCountersScsiLun } ::= { cpqFcTapeCountersTable 1 } CpqFcTapeCountersEntry ::= SEQUENCE { cpqFcTapeCountersCntlrIndex INTEGER, cpqFcTapeCountersScsiBus INTEGER, cpqFcTapeCountersScsiTarget INTEGER, cpqFcTapeCountersScsiLun INTEGER, cpqFcTapeCountersReWrites Counter, cpqFcTapeCountersReReads Counter, cpqFcTapeCountersTotalErrors Counter, cpqFcTapeCountersTotalUncorrectable Counter, cpqFcTapeCountersTotalBytes Counter } cpqFcTapeCountersCntlrIndex OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Counters Controller Index. This value is a logical number whose meaning is OS dependent. Each tape controller has one unique controller number associated with it." ::= { cpqFcTapeCountersEntry 1 } cpqFcTapeCountersScsiBus OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Counters Scsi Bus. The bus index indicates to which SCSI bus instance on a tape controller this table entry belongs." ::= { cpqFcTapeCountersEntry 2 } cpqFcTapeCountersScsiTarget OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Counters Scsi Target. The target index indicates to which SCSI ID on a tape controller SCSI bus this table entry belongs." ::= { cpqFcTapeCountersEntry 3 } cpqFcTapeCountersScsiLun OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Tape Counters Scsi Lun. The Lun index indicates to which logical unit on a SCSI ID on a tape controller SCSI bus this table entry belongs." ::= { cpqFcTapeCountersEntry 4 } cpqFcTapeCountersReWrites OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Tape Device Re-write count. This is the number of times blocks had to be re-written to the device. This value is maintained since the Tape Hardware Interface driver was loaded. Re-write errors may occasionally occur. If this value should rise dramatically, you may need to clean the device. If you continue to have re-writes, you may have a problem. Some common causes include radio frequency interference (RFI) on the bus cables, bad or missing terminating resisters on the drives or having more than one device with the same SCSI ID. Insure the bus cable is free of obstructions and that the devices on the bus are properly configured." ::= { cpqFcTapeCountersEntry 5 } cpqFcTapeCountersReReads OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Tape Device Re-read count. This is the number of times blocks had to be re-read from the device. This value is maintained since the Tape Hardware Interface driver was loaded. Re-read errors may occasionally occur. If this value should rise dramatically, you may need to clean the device. If you continue to have re-reads, you may have a problem. Some common causes include radio frequency interference (RFI) on the bus cables, bad or missing terminating resisters on the drives or having more than one device with the same SCSI ID. Insure the bus cable is free of obstructions and that the devices on the bus are properly configured." ::= { cpqFcTapeCountersEntry 6 } cpqFcTapeCountersTotalErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Tape Device Total Errors. This is the total number of read/write errors encountered. This value is maintained since the Tape Hardware Interface driver was loaded. Errors may occasionally occur. If this value should rise dramatically, you may need to clean the device. If you continue to have errors, you may have a problem. Some common causes include radio frequency interference (RFI) on the bus cables, bad or missing terminating resisters on the drives or having more than one device with the same SCSI ID. Insure the bus cable is free of obstructions and that the devices on the bus are properly configured." ::= { cpqFcTapeCountersEntry 7 } cpqFcTapeCountersTotalUncorrectable OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Tape Device Total Uncorrectable Errors. This is the total number of read and write errors which could not be corrected. This value is maintained since the Tape Hardware Interface driver was loaded. Errors may occasionally occur. If this value should rise dramatically, you may need to clean the device. If you continue to have errors, you may have a problem. Some common causes include radio frequency interference (RFI) on the bus cables, bad or missing terminating resisters on the drives or having more than one device with the same SCSI ID. Insure the bus cable is free of obstructions and that the devices on the bus are properly configured." ::= { cpqFcTapeCountersEntry 8 } cpqFcTapeCountersTotalBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Tape Device Total Bytes. This is the number total number of bytes read/written to the tape currently installed in the device. This value is reset whenever a new tape is inserted into the device." ::= { cpqFcTapeCountersEntry 9 } -- **************************************************************************** -- Fibre Channel Switch Group -- ========================== -- -- The compaq enterprise (1.3.6.1.4.1.232) -- cpqFibreArray Group (1.3.6.1.4.1.232.16) -- cpqFcSwitchComponent Group (1.3.6.1.4.1.232.16.4) -- cpqFcSwitch Group (1.3.6.1.4.1.232.16.4.1) -- cpqFcSwitchTable (1.3.6.1.4.1.232.16.4.1.1) -- -- The Fibre channel switch group contains the configuration -- information for Fibre channel switches. -- -- Implementation of the cpqFcSwitch group is mandatory for all agents -- that support the Compaq Fibre Channel MIB. -- -- **************************************************************************** cpqFcSwitchTable OBJECT-TYPE SYNTAX SEQUENCE OF CpqFcSwitchEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Compaq Fibre Channel Switch Table." ::= { cpqFcSwitch 1 } cpqFcSwitchEntry OBJECT-TYPE SYNTAX CpqFcSwitchEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Compaq Fibre Channel Switch Entry." INDEX { cpqFcSwitchIndex } ::= { cpqFcSwitchTable 1 } CpqFcSwitchEntry ::= SEQUENCE { cpqFcSwitchIndex INTEGER, cpqFcSwitchLocation INTEGER, cpqFcSwitchChassisIndex INTEGER, cpqFcSwitchChassisSlot INTEGER, cpqFcSwitchWorldWideNodeName DisplayString, cpqFcSwitchWorldWidePortName DisplayString, cpqFcSwitchIpAddress DisplayString, cpqFcSwitchIpGateway DisplayString, cpqFcSwitchIpSubnet DisplayString, cpqFcSwitchName DisplayString, cpqFcSwitchNetworkLinkStatus INTEGER, cpqFcSwitchFibreConnectStatus INTEGER } cpqFcSwitchIndex OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Switch Index. This value is a logical number whose meaning is OS dependent. Each switch has one unique controller number associated with it." ::= { cpqFcSwitchEntry 1 } cpqFcSwitchLocation OBJECT-TYPE SYNTAX INTEGER { other(1), internal(2), external(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Switch Location. The following values are defined: other(1) The agent is unable to determine if the switch is internal or external to the storage system chassis. internal(2) The switch is located in the storage system chassis. external(3) The switch is located outside the storage system chassis." ::= { cpqFcSwitchEntry 2 } cpqFcSwitchChassisIndex OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Switch Chassis Index. The chassis index indicates the storage system in which this switch resides. If the switch does not reside in a storage system chassis, then this field is invalid and a value of 65535 will be returned." ::= { cpqFcSwitchEntry 3 } cpqFcSwitchChassisSlot OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Switch Chassis Slot. The chassis slot identifies the physical slot of the storage system in which this switch resides. If the switch does not reside in a storage system chassis, then this field is invalid and a value of 255 will be returned." ::= { cpqFcSwitchEntry 4 } cpqFcSwitchWorldWideNodeName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..16)) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Switch World Wide Node Name. This value can be used to further identify a particular controller. If the world wide node name is not supported, the agent will return a NULL string." ::= { cpqFcSwitchEntry 5 } cpqFcSwitchWorldWidePortName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..16)) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Switch World Wide Port Name. This value can be used to further identify a particular controller. If the world wide port name is not supported, the agent will return a NULL string." ::= { cpqFcSwitchEntry 6 } cpqFcSwitchIpAddress OBJECT-TYPE SYNTAX DisplayString (SIZE (0..15)) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Switch IP Address. This is the IP address of the switch. If the IP address is not supported, the agent will return a NULL string." ::= { cpqFcSwitchEntry 7 } cpqFcSwitchIpGateway OBJECT-TYPE SYNTAX DisplayString (SIZE (0..15)) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Switch IP Gateway. This is the IP gateway of the switch. If the IP gateway is not supported, the agent will return a NULL string." ::= { cpqFcSwitchEntry 8 } cpqFcSwitchIpSubnet OBJECT-TYPE SYNTAX DisplayString (SIZE (0..15)) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Switch IP Subnet. This is the IP subnet of the switch. If the IP subnet is not supported, the agent will return a NULL string." ::= { cpqFcSwitchEntry 9 } cpqFcSwitchName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Switch Name. This is the name of the switch. If the name is not supported, the agent will return a NULL string." ::= { cpqFcSwitchEntry 10 } cpqFcSwitchNetworkLinkStatus OBJECT-TYPE SYNTAX INTEGER { other(1), active(2), notActive(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Switch Network Link Status. The following values are defined: other(1) The agent is unable to determine the status of the switch network link. active(2) The switch network link is active. notActive(3) The switch network link is not active." ::= { cpqFcSwitchEntry 11 } cpqFcSwitchFibreConnectStatus OBJECT-TYPE SYNTAX INTEGER { other(1), ok(2), offline(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Compaq Fibre Channel Switch Fibre Channel Connection Status. The following values are defined: other(1) The agent is unable to determine the status of the switch fibre channel connection. ok(2) The switch Fibre Channel connection is OK. offline(3) The switch Fibre Channel connection is offline." ::= { cpqFcSwitchEntry 12 } -- ************************************************************************** -- Compaq Fibre Channel Array Trap Definitions -- =========================================== -- -- The compaq enterprise (1.3.6.1.4.1.232) -- -- The SNMP trap messages must not be bigger than 484 octets (bytes). -- -- Trap support in an SNMP agent implementation is optional. An SNMP -- agent implementation may support all, some, or none of the traps. -- If traps are supported, the user should be provided with the option of -- disabling traps. -- -- ************************************************************************** cpqFcaLogDrvStatusChange TRAP-TYPE ENTERPRISE compaq VARIABLES { sysName, cpqHoTrapFlags, cpqSsChassisName, cpqSsChassisTime, cpqFcaLogDrvIndex, cpqFcaLogDrvStatus } DESCRIPTION "Fibre Channel Array Logical Drive Status Change. This trap signifies that the agent has detected a change in the status of a Compaq Fibre Channel Array logical drive. The variable cpqFcaLogDrvStatus indicates the current logical drive status. User Action: If the logical drive status is failed, examine the array for failed drives that need replacement." --#TYPE "Logical Drive Status Change" --#SUMMARY "Status is now %d." --#ARGUMENTS {5} --#SEVERITY CRITICAL --#TIMEINDEX 99 ::= 16001 cpqFcaSpareStatusChange TRAP-TYPE ENTERPRISE compaq VARIABLES { sysName, cpqHoTrapFlags, cpqSsChassisName, cpqSsChassisTime, cpqFcaSpareBusNumber, cpqFcaSpareBay, cpqFcaSpareStatus } DESCRIPTION "Fibre Channel Array Spare Drive Status Change. This trap signifies that the agent has detected a change in the status of a Compaq Fibre Channel Array spare drive. The variable cpqFcaSpareStatus indicates the current spare drive status. The variable cpqFcaSpareBusNumber indicates the SCSI bus number associated with this drive. User Action: If the spare drive status is failed, replace the drive." --#TYPE "Spare Drive Status Change" --#SUMMARY "Spare Status is now %d on bus %d." --#ARGUMENTS {6,4} --#SEVERITY CRITICAL --#TIMEINDEX 99 ::= 16002 cpqFcaPhyDrvStatusChange TRAP-TYPE ENTERPRISE compaq VARIABLES { sysName, cpqHoTrapFlags, cpqSsChassisName, cpqSsChassisTime, cpqFcaPhyDrvBusNumber, cpqFcaPhyDrvBay, cpqFcaPhyDrvStatus } DESCRIPTION "Fibre Channel Array Physical Drive Status Change. This trap signifies that the agent has detected a change in the status of a Compaq Drive Array physical drive. The variable cpaFcaPhyDrvStatus indicates the current physical drive status. The variable cpqFcaPhyDrvBusNumber indicates the SCSI bus number associated with this drive. User Action: If the physical drive status is threshExceeded(4), predictiveFailure(5) or failed(6), replace the drive." --#TYPE "Physical Drive Status Change" --#SUMMARY "Status is now %d for a physical drive on bus %d." --#ARGUMENTS {6,4} --#SEVERITY CRITICAL --#TIMEINDEX 99 ::= 16003 cpqFcaAccelStatusChange TRAP-TYPE ENTERPRISE compaq VARIABLES { sysName, cpqHoTrapFlags, cpqSsChassisName, cpqSsChassisTime, cpqFcaAccelBoxIoSlot, cpqFcaAccelStatus } DESCRIPTION "Fibre Channel Array Accelerator Board Status Change. This trap signifies that the agent has detected a change in the cpqFcaAccelStatus of a Compaq Array Accelerator Cache Board. The current status is represented by the variable cpqFcaAccelStatus. User Action: None." --#TYPE "Accelerator Board Status Change" --#SUMMARY "Status is now %d." --#ARGUMENTS {5} --#SEVERITY CRITICAL --#TIMEINDEX 99 ::= 16004 cpqFcaAccelBadDataTrap TRAP-TYPE ENTERPRISE compaq VARIABLES { sysName, cpqHoTrapFlags, cpqSsChassisName, cpqSsChassisTime, cpqFcaAccelBoxIoSlot } DESCRIPTION "Fibre Channel Array Accelerator Board Bad Data. This trap signifies that the agent has detected a Compaq Array Accelerator Cache Board that has lost battery power. If data was being stored in the accelerator memory when the system lost power, that data has been lost. User Action: Verify that no data has been lost." --#TYPE "Accelerator Board Bad Data" --#SUMMARY "Accelerator lost battery power. Data Loss possible." --#ARGUMENTS {} --#SEVERITY CRITICAL --#TIMEINDEX 99 ::= 16005 cpqFcaAccelBatteryFailed TRAP-TYPE ENTERPRISE compaq VARIABLES { sysName, cpqHoTrapFlags, cpqSsChassisName, cpqSsChassisTime, cpqFcaAccelBoxIoSlot } DESCRIPTION "Fibre Channel Array Accelerator Board Battery Failed. This trap signifies that the agent has detected a battery failure associated with the Compaq Array Accelerator Cache Board. User Action: Replace the Accelerator Cache Board." --#TYPE "Accelerator Board Battery Failed" --#SUMMARY "Battery status is failed." --#ARGUMENTS {} --#SEVERITY CRITICAL --#TIMEINDEX 99 ::= 16006 cpqFcaCntlrStatusChange TRAP-TYPE ENTERPRISE compaq VARIABLES { sysName, cpqHoTrapFlags, cpqSsChassisName, cpqSsChassisTime, cpqFcaCntlrBoxIoSlot, cpqFcaCntlrStatus } DESCRIPTION "Fibre Channel Array Array Controller Status Change. This trap signifies that the agent has detected a change in the status of a Compaq Fibre Channel Array Controller. The variable cpqFcaCntlrStatus indicates the current controller status. User Action: If the controller status is offline, access to the storage box has been lost. Check the storage box and all fibre fhannel connections for problems." --#TYPE "Array Controller Status Change" --#SUMMARY "Status is now %d." --#ARGUMENTS {5} --#SEVERITY CRITICAL --#TIMEINDEX 99 ::= 16007 cpqFcTapeCntlrStatusChange TRAP-TYPE ENTERPRISE compaq VARIABLES { sysName, cpqHoTrapFlags, cpqFcTapeCntlrWWN, cpqFcTapeCntlrStatus } DESCRIPTION "Fibre Channel Tape Controller Status Change. This trap signifies that the agent has detected a change in the status of a Compaq Fiber Channel Tape Controller. The variable cpqFcTapeCntlrStatus indicates the current tape controller status. The variable cpqFcTapeCntlrWWN indicates the unique tape controller world wide name associated with this controller. User Action: If the tape controller status is offline, access to the tape library and tapes has been lost. Check the tape library and all Fibre connections for problems." --#TYPE "Tape Controller Status Change" --#SUMMARY "Status is now %d for tape controller %s." --#ARGUMENTS {3,2} --#SEVERITY CRITICAL --#TIMEINDEX 99 ::= 16008 cpqFcTapeLibraryStatusChange TRAP-TYPE ENTERPRISE compaq VARIABLES { sysName, cpqHoTrapFlags, cpqFcTapeCntlrWWN, cpqFcTapeLibraryScsiBus, cpqFcTapeLibraryScsiTarget, cpqFcTapeLibraryScsiLun, cpqFcTapeLibraryStatus} DESCRIPTION "Fibre Channel Tape Library Status Change. This trap signifies that the agent has detected a change in the status of a Compaq Fiber Channel Tape library. The variable cpqFcTapeLibraryStatus indicates the current tape library status. The variable cpqFcTapeLibraryScsiTarget indicates the SCSI ID of the tape library. User Action: If the tape library is failed or offline, check the tape library front panel and all fibre channel connections." --#TYPE "Tape Library Status Change" --#SUMMARY "Status is now %d for the tape library." --#ARGUMENTS {6} --#SEVERITY CRITICAL --#TIMEINDEX 99 ::= 16009 cpqFcTapeLibraryDoorStatusChange TRAP-TYPE ENTERPRISE compaq VARIABLES { sysName, cpqHoTrapFlags, cpqFcTapeCntlrWWN, cpqFcTapeLibraryScsiBus, cpqFcTapeLibraryScsiTarget, cpqFcTapeLibraryScsiLun, cpqFcTapeLibraryDoorStatus} DESCRIPTION "Fibre Channel Tape Library Door Status Change. This trap signifies that the agent has detected a change in the door status of a Compaq Fiber Channel Tape library. The variable cpqFcTapeLibraryDoorStatus indicates the current tape library door status. The variable cpqFcTapeLibraryScsiTarget indicates the the SCSI ID of the tape library. User Action: If the tape library door is open, close the tape library door." --#TYPE "Tape Library Door Status Change" --#SUMMARY "The door is %d for tape library." --#ARGUMENTS {6} --#SEVERITY CRITICAL --#TIMEINDEX 99 ::= 16010 cpqFcTapeDriveStatusChange TRAP-TYPE ENTERPRISE compaq VARIABLES { sysName, cpqHoTrapFlags, cpqFcTapeCntlrWWN, cpqFcTapeDriveScsiBus, cpqFcTapeDriveScsiTarget, cpqFcTapeDriveScsiLun, cpqFcTapeDriveStatus} DESCRIPTION "Fibre Channel Tape Drive Status Change. This trap signifies that the agent has detected a change in the status of a Compaq Fiber Channel Tape Drive. The variable cpqFcTapeDriveStatus indicates the current tape status. The variable cpqFcTapeDriveScsiTarget indicates the the SCSI ID of the tape drive. User Action: If the tape is failed or offline, check the tape and all fibre channel connections." --#TYPE "Tape Drive Status Change" --#SUMMARY "Status is now %d for a tape drive." --#ARGUMENTS {6} --#SEVERITY CRITICAL --#TIMEINDEX 99 ::= 16011 cpqFcTapeDriveCleaningRequired TRAP-TYPE ENTERPRISE compaq VARIABLES { sysName, cpqHoTrapFlags, cpqFcTapeCntlrWWN, cpqFcTapeDriveScsiBus, cpqFcTapeDriveScsiTarget, cpqFcTapeDriveScsiLun} DESCRIPTION "Fibre Channel Tape Drive Cleaning Required trap. The agent has detected a tape drive that needs to have a cleaning tape inserted and run. This will cause the tape drive heads to be cleaned." --#TYPE "Tape Drive Cleaning Required" --#SUMMARY "Cleaning is needed for tape drive." --#ARGUMENTS {} --#SEVERITY MAJOR --#TIMEINDEX 99 ::= 16012 cpqFcTapeDriveCleanTapeReplace TRAP-TYPE ENTERPRISE compaq VARIABLES { sysName, cpqHoTrapFlags, cpqFcTapeCntlrWWN, cpqFcTapeDriveScsiBus, cpqFcTapeDriveScsiTarget, cpqFcTapeDriveScsiLun} DESCRIPTION "Fibre Channel Tape Drive Cleaning Tape Needs Replacing. The agent has detected that an autoloader tape unit has a cleaning tape that has been fully used and therefore needs to be replaced with a new cleaning tape." --#TYPE "Tape Drive Cleaning Tape Needs Replacing" --#SUMMARY "Cleaning tape needs replacing" --#ARGUMENTS {} --#SEVERITY MAJOR --#TIMEINDEX 99 ::= 16013 cpqFcaCntlrActive TRAP-TYPE ENTERPRISE compaq VARIABLES { sysName, cpqHoTrapFlags, cpqSsChassisName, cpqSsChassisTime, cpqFcaCntlrBoxIoSlot } DESCRIPTION "Fibre Array Controller Active. This trap signifies that the Storage Agent has detected that a backup array controller in a duplexed pair has switched over to the active role. The variable cpqFcaCntlrBoxIoSlot indicates the new active controller index. User Action: Check the partner controller for problems. If this was the result of a user initiated switch over, no action is required." --#TYPE "Redundant Controller Active" --#SUMMARY "Controller in i/o slot %d is now active on chassis %s." --#ARGUMENTS {4,2} --#SEVERITY INFORMATIONAL --#TIMEINDEX 99 ::= 16014 cpqFcaHostCntlrStatusChange TRAP-TYPE ENTERPRISE compaq VARIABLES { sysName, cpqHoTrapFlags, cpqFcaHostCntlrSlot, cpqFcaHostCntlrStatus } DESCRIPTION "Fibre Channel Host Controller Status Change. This trap signifies that the Insight Agent has detected a change in the status of a Compaq Fibre Channel Host Controller. The variable cpqFcaHostCntlrStatus indicates the current controller status. User Action: If the controller status is failed, replace the controller." --#TYPE "Fibre Channel Host Controller Status Change" --#SUMMARY "Host controller in slot %d has a new status of %d." --#ARGUMENTS {2,3} --#SEVERITY CRITICAL --#TIMEINDEX 99 ::= 16015 cpqFca2PhyDrvStatusChange TRAP-TYPE ENTERPRISE compaq VARIABLES { sysName, cpqHoTrapFlags, cpqSsChassisName, cpqSsChassisTime, cpqFcaPhyDrvBusNumber, cpqFcaPhyDrvBay, cpqFcaPhyDrvStatus, cpqFcaPhyDrvModel, cpqFcaPhyDrvSerialNum, cpqFcaPhyDrvFWRev, cpqFcaPhyDrvFailureCode } DESCRIPTION "Fibre Channel Array Physical Drive Status Change. This trap signifies that the agent has detected a change in the status of a Compaq Drive Array physical drive. The variable cpaFcaPhyDrvStatus indicates the current physical drive status. User Action: If the physical drive status is threshExceeded(4), predictiveFailure(5) or failed(6), replace the drive." --#TYPE "Physical Drive Status Change" --#SUMMARY "Status is now %d for a physical drive on bus %d, bay %d." --#ARGUMENTS {6,4,5} --#SEVERITY CRITICAL --#TIMEINDEX 99 ::= 16016 cpqFca2AccelStatusChange TRAP-TYPE ENTERPRISE compaq VARIABLES { sysName, cpqHoTrapFlags, cpqSsChassisName, cpqSsChassisTime, cpqFcaAccelBoxIoSlot, cpqFcaAccelStatus, cpqFcaCntlrModel, cpqFcaAccelSerialNumber, cpqFcaAccelTotalMemory, cpqFcaAccelErrCode } DESCRIPTION "Fibre Channel Array Accelerator Board Status Change. This trap signifies that the agent has detected a change in the status of a Compaq Array Accelerator Cache Board. The current status is represented by the variable cpqFcaAccelStatus. User Action: If the accelerator board status is permDisabled(5), you may need to replace the accelerator board." --#TYPE "Accelerator Board Status Change" --#SUMMARY "Status is now %d." --#ARGUMENTS {5} --#SEVERITY CRITICAL --#TIMEINDEX 99 ::= 16017 cpqFca2AccelBadDataTrap TRAP-TYPE ENTERPRISE compaq VARIABLES { sysName, cpqHoTrapFlags, cpqSsChassisName, cpqSsChassisTime, cpqFcaAccelBoxIoSlot, cpqFcaCntlrModel, cpqFcaAccelSerialNumber, cpqFcaAccelTotalMemory } DESCRIPTION "Fibre Channel Array Accelerator Board Bad Data. This trap signifies that the agent has detected a Compaq Array Accelerator Cache Board that has lost battery power. If data was being stored in the accelerator memory when the system lost power, that data has been lost. User Action: Verify that no data has been lost." --#TYPE "Accelerator Board Bad Data" --#SUMMARY "Accelerator lost battery power. Data Loss possible." --#ARGUMENTS {} --#SEVERITY CRITICAL --#TIMEINDEX 99 ::= 16018 cpqFca2AccelBatteryFailed TRAP-TYPE ENTERPRISE compaq VARIABLES { sysName, cpqHoTrapFlags, cpqSsChassisName, cpqSsChassisTime, cpqFcaAccelBoxIoSlot, cpqFcaCntlrModel, cpqFcaAccelSerialNumber, cpqFcaAccelTotalMemory } DESCRIPTION "Fibre Channel Array Accelerator Board Battery Failed. This trap signifies that the agent has detected a battery failure associated with the Compaq Array Accelerator Cache Board. User Action: Replace the Accelerator Cache Board." --#TYPE "Accelerator Board Battery Failed" --#SUMMARY "Battery status is failed." --#ARGUMENTS {} --#SEVERITY CRITICAL --#TIMEINDEX 99 ::= 16019 cpqFca2CntlrStatusChange TRAP-TYPE ENTERPRISE compaq VARIABLES { sysName, cpqHoTrapFlags, cpqSsChassisName, cpqSsChassisTime, cpqFcaCntlrBoxIoSlot, cpqFcaCntlrStatus, cpqFcaCntlrModel, cpqFcaCntlrSerialNumber, cpqFcaAccelTotalMemory } DESCRIPTION "Fibre Channel Array Array Controller Status Change. This trap signifies that the agent has detected a change in the status of a Compaq Fibre Channel Array Controller. The variable cpqFcaCntlrStatus indicates the current controller status. User Action: If the controller status is offline(4), access to the storage box has been lost. Check the storage box and all fibre channel connections for problems." --#TYPE "Array Controller Status Change" --#SUMMARY "Status is now %d." --#ARGUMENTS {5} --#SEVERITY CRITICAL --#TIMEINDEX 99 ::= 16020 cpqFca2HostCntlrStatusChange TRAP-TYPE ENTERPRISE compaq VARIABLES { sysName, cpqHoTrapFlags, cpqFcaHostCntlrSlot, cpqFcaHostCntlrStatus, cpqFcaHostCntlrModel, cpqFcaHostCntlrWorldWideName } DESCRIPTION "Fibre Channel Host Controller Status Change. This trap signifies that the agent has detected a change in the status of a Compaq Fibre Channel Host Controller. The variable cpqFcaHostCntlrStatus indicates the current controller status. User Action: If the controller status is failed, replace the controller." --#TYPE "Fibre Channel Host Controller Status Change" --#SUMMARY "Host controller in slot %d has a new status of %d." --#ARGUMENTS {2,3} --#SEVERITY CRITICAL --#TIMEINDEX 99 ::= 16021 cpqExtArrayLogDrvStatusChange TRAP-TYPE ENTERPRISE compaq VARIABLES { sysName, cpqHoTrapFlags, cpqSsChassisName, cpqSsChassisTime, cpqFcaLogDrvBoxIndex, cpqFcaLogDrvIndex, cpqFcaLogDrvStatus, cpqFcaLogDrvOsName, cpqFcaLogDrvFaultTol, cpqFcaLogDrvSize } DESCRIPTION "External Array Logical Drive Status Change. This trap signifies that the agent has detected a change in the status of a Compaq External Array logical drive. The variable cpqFcaLogDrvStatus indicates the current logical drive status. User Action: If the logical drive status is failed, examine the array for failed drives that need replacement." --#TYPE "Logical Drive Status Change" --#SUMMARY "Status is now %d." --#ARGUMENTS {6} --#SEVERITY CRITICAL --#TIMEINDEX 99 ::= 16022 cpqExtTapeDriveStatusChange TRAP-TYPE ENTERPRISE compaq VARIABLES { sysName, cpqHoTrapFlags, cpqFcTapeDriveCntlrIndex, cpqFcTapeDriveScsiBus, cpqFcTapeDriveScsiTarget, cpqFcTapeDriveScsiLun, cpqFcTapeDriveModel, cpqFcTapeDriveFWRev, cpqFcTapeDriveSerialNumber, cpqFcTapeDriveLocation, cpqFcTapeDriveStatus} DESCRIPTION "External Tape Drive Status Change. This trap signifies that the agent has detected a change in the status of a Compaq External Tape Drive. The variable cpqFcTapeDriveStatus indicates the current tape status. User Action: If the tape is failed or offline, check the tape and all connections." --#TYPE "Tape Drive Status Change" --#SUMMARY "Status is now %d for a tape drive." --#ARGUMENTS {10} --#SEVERITY CRITICAL --#TIMEINDEX 99 ::= 16023 cpqExtTapeDriveCleaningRequired TRAP-TYPE ENTERPRISE compaq VARIABLES { sysName, cpqHoTrapFlags, cpqFcTapeDriveCntlrIndex, cpqFcTapeDriveScsiBus, cpqFcTapeDriveScsiTarget, cpqFcTapeDriveScsiLun, cpqFcTapeDriveModel, cpqFcTapeDriveFWRev, cpqFcTapeDriveSerialNumber, cpqFcTapeDriveLocation} DESCRIPTION "External Tape Drive Cleaning Required trap. The agent has detected a tape drive that needs to have a cleaning tape inserted and run. This will cause the tape drive heads to be cleaned." --#TYPE "Tape Drive Cleaning Required" --#SUMMARY "Cleaning is needed for tape drive." --#ARGUMENTS {} --#SEVERITY MAJOR --#TIMEINDEX 99 ::= 16024 cpqExtTapeDriveCleanTapeReplace TRAP-TYPE ENTERPRISE compaq VARIABLES { sysName, cpqHoTrapFlags, cpqFcTapeDriveCntlrIndex, cpqFcTapeDriveScsiBus, cpqFcTapeDriveScsiTarget, cpqFcTapeDriveScsiLun, cpqFcTapeDriveModel, cpqFcTapeDriveFWRev, cpqFcTapeDriveSerialNumber, cpqFcTapeDriveLocation} DESCRIPTION "External Tape Drive Cleaning Tape Needs Replacing. The agent has detected that an autoloader tape unit has a cleaning tape that has been fully used and therefore needs to be replaced with a new cleaning tape." --#TYPE "Tape Drive Cleaning Tape Needs Replacing" --#SUMMARY "Cleaning tape needs replacing" --#ARGUMENTS {} --#SEVERITY MAJOR --#TIMEINDEX 99 ::= 16025 END