-- ********************************************************************* -- CISCO-ZS-MIB.my: Zone Server Mib -- -- September 2002 H K Vivek -- -- Copyright (c) 2002-2003, 2004, 2005 by cisco Systems, Inc. -- All rights reserved. -- -- ********************************************************************* CISCO-ZS-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Counter32, Integer32, Unsigned32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF TEXTUAL-CONVENTION, RowStatus, TruthValue, TestAndIncr, TimeStamp FROM SNMPv2-TC InetAddressType, InetAddress FROM INET-ADDRESS-MIB ciscoMgmt FROM CISCO-SMI SnmpAdminString FROM SNMP-FRAMEWORK-MIB ifIndex, InterfaceIndexOrZero FROM IF-MIB vsanIndex FROM CISCO-VSAN-MIB VsanIndex, DomainIdOrZero, FcAddressId, FcNameId FROM CISCO-ST-TC FcGs3RejectReasonCode FROM CISCO-NS-MIB; ciscoZsMIB MODULE-IDENTITY LAST-UPDATED "200511100000Z" ORGANIZATION "Cisco Systems Inc." CONTACT-INFO " Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553 -NETS E-mail: cs-san@cisco.com" DESCRIPTION "The MIB module for the management of zoning within the framework of Cisco's Zoning Server (ZS) Archi- tecture which realizes the FC-GS3 requirements for Zone Server. This MIB enables managers to configure and monitor zoning server parameters. Additionally, Cisco's Zoning Server allows for configuration of Lun zoning, which is an extension to the Zoning Server standard specified by FC-GS3. Glossary of terms used ---------------------- VSAN - Virtual Storage Area Network. Zone Merge - When the ISL (Inter Switch Link) between 2 switches is brought up, the zoning databases on the 2 switches are compared by means of the Zone Merge protocol. If the 2 databases can be merged, the ISL is brought up. Otherwise, the link is isolated." REVISION "200511100000Z" DESCRIPTION "Added new enum 'ipAddrv6' to ZoneMemberType TC. Added description to the object zoneMemberID corresponding to this enum. Added zoneSetZoneListTable and zoneSetEnforcedZoneListTable to increase the number of zones that can be associated with a zoneset to 8192 from 2048. Changed the upper limit of zoneIndex and zoneMemberParentIndex objects to 8192 from 2048. Added zoneCompactTable and zoneCompactNotify. Added new enum 'deviceAlias' to ZoneMemberType TC. Deprecated zoneCopyActiveToFullOnVsan object. Added new objects zoneCopyActToFullSpinLock, zoneCopyActToFullMode and zoneCopyActToFullVsan. Enhanced zoneMergeFailure notification to include information regarding the details of merge failure." REVISION "200504070000Z" DESCRIPTION "Added zoneDbHardZoningEnabled to zoneDbTable. Added zoneSetClone, zoneClone and zoneAliasClone objects. Added zoneActivateNotify notification. Added zoneSwitchWwn object to be used in zoneActivateNotify notification." REVISION "200409010000Z" DESCRIPTION "Added objects zoneQos, zoneQosPriority, zoneBroadcast and zoneAttribObjIndex to zoneTable. Added objects zoneEnforcedZoneQos, zoneEnforcedZoneQosPriority and zoneEnforcedZoneBroadcast to zoneEnforcedZoneTable. Added zoneDefaultZoneQos, zoneDefaultZoneQosPriority and zoneDefaultZoneBroadcast to zoneDefaultZoneTable. Changed DESCRIPTION of zoneSetName and zoneAliasName objects to indicate that they support renaming." REVISION "200401270000Z" DESCRIPTION "Added zoneZoneSetDistributeVsan, zoneZoneSetDistributeResult and zoneZoneSetDistributeFailReason objects for supporting full zoneset distribution." REVISION "200312120000Z" DESCRIPTION "Added new notification zoneUnsuppMemInIntOpModeNotify and corresponding notification control object zoneUnsuppMemInIntOpNotifyEnable. Added object zoneVsanId to be used in the above notification." REVISION "200308250000Z" DESCRIPTION "Added zoneCopyTable. Added 2 new member types to ZoneMemberType TC - domainIntf and ipAddr." REVISION "200308010000Z" DESCRIPTION "Added zoneLunStatsTable and zoneRoZoneStatsTable. Changed the max size of zoneMemberID and zoneEnforcedMemberID to 255 from 256. Added zoneDefaultZoneReadOnly object to zoneDefaultZoneTable. Modified the DESCRIPTION of zoneName object in zoneTable so that it can be renamed. Added zoneAliasLastChange object to zoneAliasTable. Deprecated zoneEnforcedZoneAliasTable. Added 2 new member types (domainPort and intf) to ZoneMemberType TC." REVISION "200303260000Z" DESCRIPTION "Added TC FcChangeProtoFailCause and objects zoneSetFailCause and zoneSetFailDomId to the zoneSetActivateTable. Added objects zoneDbEnforcedEqualsLocal and zoneDbClearDb to new table zoneDbTable. Added zoneReadOnly object to zoneTable and zoneEnforcedZoneReadOnly object to zoneEnforcedZoneTable." REVISION "200301170000Z" DESCRIPTION "Added symNodeName, a new enumeration to the ZoneMemberType TC." REVISION "200211080000Z" DESCRIPTION "Added zoneCopyActiveToFullOnVsan object." REVISION "200210280000Z" DESCRIPTION "Added zoneSetPropagationTable." REVISION "200210030000Z" DESCRIPTION "Initial version of this MIB." ::= { ciscoMgmt 294 } ciscoZoningMIBObjects OBJECT IDENTIFIER ::= { ciscoZsMIB 1 } zoneServerMIBConformance OBJECT IDENTIFIER ::= { ciscoZsMIB 2 } zoneConfiguration OBJECT IDENTIFIER ::= { ciscoZoningMIBObjects 1 } zoneStats OBJECT IDENTIFIER ::= { ciscoZoningMIBObjects 2 } zoneInformation OBJECT IDENTIFIER ::= { ciscoZoningMIBObjects 3 } zoneNotification OBJECT IDENTIFIER ::= { ciscoZoningMIBObjects 4 } zoneNotifications OBJECT IDENTIFIER ::= { zoneNotification 0 } -- Textual Conventions ZoneMemberType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Represents the addressing mechanism by which a member is identified. wwn(1) - The Port World Wide Name (PWWN). domainPort(2) - Domain and Port number format. fcAddr(3) - FC-ID. fwwn(4) - Fabric Port World Wide Name. This is used for Port based zoning. symNodeName(5) - Symbolic Node Name used for iSCSI zoning. intf(6) - interface format. domainIntf(7) - Domain and Interface format. ipAddr(8) - IPv4 address format. ipAddrv6(9) - IPv6 address format. deviceAlias(10) - Device Alias. This is a human readable string used to alias a World Wide Name (WWN). It is defined in CISCO-FC-DEVICE-ALIAS-MIB." SYNTAX INTEGER { wwn(1), domainPort(2), fcAddr(3), fwwn(4), symNodeName(5), intf(6), domainIntf(7), ipAddr(8), ipAddrv6(9), deviceAlias(10) } FcZoneServerRejReasonExpl ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The reject reason code explanation for a zone server request. noAdditionalExplanation(1) - there is no additional explanation. zonesNotSupported(2) - zones are not supported. zoneSetNameUnknown(3) - zone set name is not known. noZoneSetActive(4) - no zone set is currently active. zoneNameUnknown(5) - zone name is unknown. zoneStateUnknown(6) - state of the zone is not known. incorrectPayloadLen(7) - payload len is not correct. tooLargeZoneSet(8) - zone set is larger than permitted size. deactivateZoneSetFailed(9) - deactivation of zone set failed. reqNotSupported(10) - request is not supported. capabilityNotSupported(11) - capability is not supported. zoneMemberIDTypeNotSupp(12)- type of zone member is not supported. invalidZoneSetDefinition(13) - zone set definition is invalid." SYNTAX INTEGER { noAdditionalExplanation(1), zonesNotSupported(2), zoneSetNameUnknown(3), noZoneSetActive(4), zoneNameUnknown(5), zoneStateUnknown(6), incorrectPayloadLen(7), tooLargeZoneSet(8), deactivateZoneSetFailed(9), reqNotSupported(10), capabilityNotSupported(11), zoneMemberIDTypeNotSupp(12), invalidZoneSetDefinition(13) } FcList ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Represents a list of entities. Each octet within the value of an object of this type, specifies a set of eight entities, with the first octet specifying entities 1 through 8, the second octet specifying entities 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered entity and the least significant bit represents the highest numbered entity. If the length of an object of this type is less than 256 bytes, then the entities which are not represented are not considered to be part of this list, i.e., effectively, the string is extended to be of length 256 bytes by appending bytes containing x'00'. Note that this means that the zero length string represents the 'list is empty' value." SYNTAX OCTET STRING (SIZE (0..256)) FcChangeProtoFailCause ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The reason for the failure of Change Protocol, which kicks in due to zone set activation/de-activation. none(1) - no error. rcvdSfcBusy(2) - the local Zone Server received a busy from one of the Zone Servers in the fabric in response to SFC. rcvdUfcBusy(3) - the local Zone Server received a busy from one of the Zone Servers in the fabric in response to UFC. acaRetryExceed(4) - the number of ACA retries by the local Zone Server has exceeded the retry count. sfcRetryExceed(5) - the number of SFC retries by the local Zone Server has exceeded the retry count. ufcRetryExceed(6) - the number of UFC retries by the local Zone Server has exceeded the retry count. unsuppCmd(7) - the local Zone Server has received response from one of the Zone Servers in the fabric that it does not support the particular command. notAuth(8) - the local Zone Server has received response from one of the Zone Servers in the fabric that the local Zone Server is not authorized to carry out the particular command. fabricChange(9) - the local Zone Server has received response from one of the Zone Servers that the fabric from it's viewpoint is changing. updateNotStaged(10) - the local Zone Server has received response from one of the Zone Servers in the fabric that it has received a UFC before an SFC. invalidZsetFormat(11) - the local Zone Server has received response from one of the Zone Servers in the fabric that the zone set format in the pdu sent to it is invalid. systemErr(12) - a system error has occured on the local Zone Server. vsanNotPresent(13) - the specified VSAN is not present on the local Zone Server. vsanInactive(14) - the specifed VSAN is not active on the local Zone Server. zsetNotPresent(15) - the specified zone set is not present on the local Zone Server. dbUpdateInProgress(16) - the local Zone Server's database is being updated. zsetNotActive(17) - the zone set specified for deactivation is not active on the local Zone Server. hwOperFailed(18) - the hardware update on the local Zone Server failed. fc2SeqSizeExceed(19) - the Change Protocol frame has exceeded the allowed maximum FC-2 sequence size on the local Zone Server. fc2SendFailed(20) - the FC-2 stack failed to send the frame on the local Zone Server. zsetUnchangedAndActive(21) - the zone set specified for activation is already active and unchanged since the last activation on the local Zone Server. fabricUnstable(22) - the fabric has become unstable as detected by the local Zone Server. nonInteropMember(23) - one or more of the members specified in the zone set(s) to be activated, are in non-interoperable format and the interop mode is turned on, on the local Zone Server. lcUpgradeInProgress(24) - line card upgrade is in progress on the local Zone Server." SYNTAX INTEGER { none(1), rcvdSfcBusy(2), rcvdUfcBusy(3), acaRetryExceed(4), sfcRetryExceed(5), ufcRetryExceed(6), unsuppCmd(7), notAuth(8), fabricChange(9), updateNotStaged(10), invalidZsetFormat(11), systemErr(12), vsanNotPresent(13), vsanInactive(14), zsetNotPresent(15), dbUpdateInProgress(16), zsetNotActive(17), hwOperFailed(18), fc2SeqSizeExceed(19), fc2SendFailed(20), zsetUnchangedAndActive(21), fabricUnstable(22), nonInteropMember(23), lcUpgradeInProgress(24) } ZoneCopyProtocol ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The protocol to be used for copying the active zoneset over the network. If the copy is to occur on the local device, then the method of transfer is left to the implementation and is not restricted to these protocols." SYNTAX INTEGER { tftp(1), ftp(2), sftp(3), scp(4) } ZoneFileType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The various types of files onto which the active zoneset can be copied. networkFile(1) - the active zoneset needs to be copied over the network. localFile(2) - the active zoneset needs to be copied to a file on the local device." SYNTAX INTEGER { networkFile(1), localFile(2) } ZoneQosPriorityLevel ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Specifies the priority level for qos attribute applied to a zone. none - not applicable. low - indicates low priority. medium - indicates medium priority. high - indicates high priority." SYNTAX INTEGER { none(1), low(2), medium(3), high(4) } ZoneMergeFailCause ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Specifies the reason for zone merge failure. When the Zone Merge takes place, the local database is compared with the database of the adjacent switch. The following errors/mismatches can take place: other - reason other than those specified below. zoningModeMismatch - mismatch in zoning modes between the 2 switches. qosNotEnabled - qos is not enabled on one of the switches and qos attribute is present in one of the zones. qosConflict - conflict between VSAN based Qos and zone attribute qos. bcastNotEnabled - broadcast service has not been enabled on one of the switches and broadcast attribute is present in one of the zones. mergeCtrlMismatch - there is a mismatch in the merge control flag value. defZoneMismatch - there is a mismatch in the default zone policy. qosAttrMissing - qos attribute is missing. bcastAttrMissing - broadcast attribute is missing. rdonlyAttrMissing - read only attribute is missing. memberMismatch - there is a mismatch in the members. invPayloadFormat - the payload format is invalid. sizeExceeded - the payload exceeded the maximum size. unlicensedMember - a member is unlicensed. nonInteropZoneset - a zone attribute/member which cannot be supported in the current interop mode of the switch." SYNTAX INTEGER { other(1), zoningModeMismatch(2), qosNotEnabled(3), qosConflict(4), bcastNotEnabled(5), mergeCtrlMismatch(6), defZoneMismatch(7), qosAttrMissing(8), bcastAttrMissing(9), rdonlyAttrMissing(10), memberMismatch(11), invPayloadFormat(12), sizeExceeded(13), unlicensedMember(14), nonInteropZoneset(15) } -- -- zoneDefaultZoneTable -- zoneDefaultZoneTable OBJECT-TYPE SYNTAX SEQUENCE OF ZoneDefaultZoneEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing information on all default zones on all VSANs on the local Zone Server." ::= { zoneConfiguration 1 } zoneDefaultZoneEntry OBJECT-TYPE SYNTAX ZoneDefaultZoneEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in this table." INDEX { vsanIndex } ::= { zoneDefaultZoneTable 1 } ZoneDefaultZoneEntry ::= SEQUENCE { zoneDefaultZoneBehaviour INTEGER, zoneDefaultZoneReadOnly TruthValue, zoneDefaultZoneQos TruthValue, zoneDefaultZoneQosPriority ZoneQosPriorityLevel, zoneDefaultZoneBroadcast TruthValue } zoneDefaultZoneBehaviour OBJECT-TYPE SYNTAX INTEGER { permit(1), -- allow communication deny(2) -- deny communication } MAX-ACCESS read-write STATUS current DESCRIPTION "This object controls the behaviour of the default zone on this VSAN. If this object is set to 'permit', then the members of the default zone on this VSAN can communicate with each other. If this object is set to 'deny', then the members of the default zone on this VSAN cannot communicate with each other." DEFVAL { deny } ::= { zoneDefaultZoneEntry 1 } zoneDefaultZoneReadOnly OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates if only SCSI read operations are allowed on members of the default zone which are SCSI targets, on this VSAN. If this object is set to 'true', then only SCSI read operations are permitted. So, this default zone becomes a read-only default zone on this VSAN. If this object is set to 'false', then both SCSI read and write operations are permitted." DEFVAL { false } ::= { zoneDefaultZoneEntry 2 } zoneDefaultZoneQos OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies if qos attribute for the default zone on this VSAN is enabled. If this object is set to 'true', then qos attribute for the default zone on this VSAN is enabled. If this object is set to 'false', then qos attribute for the default zone on this VSAN is disabled. If this attribute is enabled for this default zone, then only traffic with the configured priority level will be allowed between the members of this default zone. The priority can be specified by means of the corresponding instance of zoneDefaultZoneQosPriority object." ::= { zoneDefaultZoneEntry 3 } zoneDefaultZoneQosPriority OBJECT-TYPE SYNTAX ZoneQosPriorityLevel MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the qos priority value. The value of this object is relevant only if the corresponding instance of zoneDefaultZoneQos object is enabled by setting it to 'true'." DEFVAL { none } ::= { zoneDefaultZoneEntry 4 } zoneDefaultZoneBroadcast OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies if broadcast zoning is enabled on this default zone on this VSAN. If this object is set to 'true', then it is enabled. If this object is set to 'false', then it is disabled. If broadcast zoning is enabled on this default zone, then broadcast frames generated by a member in this default zone will be restricted to members in this default zone." ::= { zoneDefaultZoneEntry 5 } -- -- zoneSetPropagationTable -- zoneSetPropagationTable OBJECT-TYPE SYNTAX SEQUENCE OF ZoneSetPropagationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing information related to propagation of zone set information during Merge/Change protocols on all VSANs on the local Zone Server." ::= { zoneConfiguration 2 } zoneSetPropagationEntry OBJECT-TYPE SYNTAX ZoneSetPropagationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in this table." INDEX { vsanIndex } ::= { zoneSetPropagationTable 1 } ZoneSetPropagationEntry ::= SEQUENCE { zoneSetPropagationMode INTEGER } zoneSetPropagationMode OBJECT-TYPE SYNTAX INTEGER { fullZoneSet(1), activeZoneSet(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object controls the way zone set information is propagated during Merge/Change protocols on this VSAN. If this object is set to 'fullZoneSet', then the entire zone set database is sent during Change/Merge protocol exchanges on this VSAN. If this object is set to 'activeZoneSet', only the active zone set is sent during Change/Merge protocol exchanges on this VSAN." DEFVAL { activeZoneSet } ::= { zoneSetPropagationEntry 1 } zoneSetNumber OBJECT-TYPE SYNTAX Integer32 (0..8388608) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of entries currently present in the zoneSetTable." ::= { zoneConfiguration 3 } -- -- zoneSetTable -- zoneSetTable OBJECT-TYPE SYNTAX SEQUENCE OF ZoneSetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing information on each Zone Set which is configured and available on any VSAN known to the local Zone Server. The zoneSetTable lists all the zone sets configured on all the VSANs configured on the local zone server. There could be multiple zone sets configured on a VSAN. But only one zone set is allowed to be active at a time in each VSAN. A Zone Set is a collection of zones." ::= { zoneConfiguration 4 } zoneSetEntry OBJECT-TYPE SYNTAX ZoneSetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the zoneSetTable. The zone sets are defined with respect to a VSAN. Hence, this table is indexed by the vsanIndex, in addition to the zoneSetIndex. The sequence of operations to be performed in order to create a zone set is as follows: - create zone entries in the ZoneTable. - create an entry in this table and set the zoneSetZoneList bitmap object to contain the required zones. - Note that it is perfectly valid to create an empty zone set." INDEX { vsanIndex, zoneSetIndex } ::= { zoneSetTable 1 } ZoneSetEntry ::= SEQUENCE { zoneSetIndex Unsigned32, zoneSetName SnmpAdminString, zoneSetZoneList FcList, zoneSetLastChange TimeStamp, zoneSetRowStatus RowStatus, zoneSetClone SnmpAdminString } zoneSetIndex OBJECT-TYPE SYNTAX Unsigned32 (1..2048) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of a zone set. This object uniquely identifies a zone set on a particular VSAN." ::= { zoneSetEntry 1 } zoneSetName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..64)) MAX-ACCESS read-create STATUS current DESCRIPTION "The name of this zone set. The zoneSetName should be unique within a VSAN. The zone set can be renamed by setting this object to a new value. This object MUST be set before or concurrently with setting the corresponding instance of zoneSetRowStatus to 'active'." ::= { zoneSetEntry 2 } zoneSetZoneList OBJECT-TYPE SYNTAX FcList MAX-ACCESS read-create STATUS current DESCRIPTION "The set of zones which form this zone set on this VSAN. The zones are identified by zoneIndex object in the zoneTable. If a particular bit has a value of '1', then the corresponding zone is a part of this zone set. All other zones have '0' in their positions or not present in the string. The default value is the zero length string." DEFVAL { ''H } ::= { zoneSetEntry 3 } zoneSetLastChange OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time of the last change to this zone set entry. If the entry has not been modified since the last re-initialization of the local network management system, then this object will contain a zero value." ::= { zoneSetEntry 4 } zoneSetRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. This object can not be set to 'active' unless the corresponding value of zoneSetName is unique within the VSAN." ::= { zoneSetEntry 5 } zoneSetClone OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..64)) MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this object to a name will result in this zone set being cloned and the cloned zone set will be set to this name. When this object is read, the zero-length string is returned." ::= { zoneSetEntry 6 } -- -- zoneSetActivateTable -- zoneSetActivateTable OBJECT-TYPE SYNTAX SEQUENCE OF ZoneSetActivateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains atmost one entry for each VSAN that is configured. These entries reflect the state of the activation of a zone set on the corresponding VSAN. The management station needs to create an entry in this table on the desired VSAN before a zone set can be activated on that VSAN." ::= { zoneConfiguration 5 } zoneSetActivateEntry OBJECT-TYPE SYNTAX ZoneSetActivateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in this table." INDEX { vsanIndex } ::= { zoneSetActivateTable 1 } ZoneSetActivateEntry ::= SEQUENCE { zoneSetActivate Unsigned32, zoneSetActivateResult INTEGER, zoneSetDeActivate INTEGER, zoneSetActivateRowStatus RowStatus, zoneSetFailCause FcChangeProtoFailCause, zoneSetFailDomId DomainIdOrZero } zoneSetActivate OBJECT-TYPE SYNTAX Unsigned32 (1..2048) MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this object to a value is a request for a zone set to be activated on the particular VSAN, i.e., for the current configuration of that zone set to be cloned with the clone becoming the active zone set for the particular VSAN. Setting this object to a value (say, N) identifies the zone set to be cloned as the zone set identified by zoneSetIndex object having the same value N. Even though there could be multiple zone sets on a VSAN, only one can be active at a time. If a zone set is already active on a VSAN and a second zone set is activated on the same VSAN, then the first zone set is automatically deactivated and the second zone set is activated. The value of this object when read is always 0." ::= { zoneSetActivateEntry 1 } zoneSetActivateResult OBJECT-TYPE SYNTAX INTEGER { activateSuccess(1), -- activation success activateFailure(2), -- activation failure deactivateSuccess(3), -- deactivation success deactivateFailure(4), -- deactivation failure inProgress(5), -- in progress newEntry(6) -- entry just created } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the outcome of the most recent activation/deactivation. When the value of this object is 'inProgress', the values of the corresponding instances of zoneSetActivate, zoneSetDeActivate and zoneSetActivateRowStatus cannot be modified. The value 'newEntry' indicates that after the entry has been created, activation/de-activation has not yet been attempted on the entry." ::= { zoneSetActivateEntry 2 } zoneSetDeActivate OBJECT-TYPE SYNTAX INTEGER { deactivate(1), -- deactivate zone set noop(2) -- no operation } MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this object to 'deactivate' is a request to deactivate the currently active zone set on this VSAN. No action is taken if this object is set to 'noop'. The value of this object when read is always 'noop'." ::= { zoneSetActivateEntry 3 } zoneSetActivateRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row." ::= { zoneSetActivateEntry 4 } zoneSetFailCause OBJECT-TYPE SYNTAX FcChangeProtoFailCause MAX-ACCESS read-only STATUS current DESCRIPTION "The reason for the failure of the zone set activation/de-activation. The value of this object contains the reason for the failure only if the value of the corresponding instance of zoneSetActivateResult is either 'activateFailure' or 'deactivateFailure'." ::= { zoneSetActivateEntry 5 } zoneSetFailDomId OBJECT-TYPE SYNTAX DomainIdOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "The domain id of the device in the fabric that has caused the Change Protocol to fail. This object will contain a valid domain id if the activation/deactivation has failed and the corresponding instance of zoneSetFailCause has a value between rcvdSfcBusy(2) and invalidZsetFormat(11). These errors are flagged by Zone Server modules running on other devices in the entire fabric as part of the Change Protocol. The remaining errors are those that are detected on the local Zone Server. In that case, this object will contain the value 0." ::= { zoneSetActivateEntry 6 } zoneNumber OBJECT-TYPE SYNTAX Integer32 (0..8388608) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of entries currently present in the zoneTable." ::= { zoneConfiguration 6 } -- -- zoneTable -- zoneTable OBJECT-TYPE SYNTAX SEQUENCE OF ZoneEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table gives information on all the zones/aliases and lists all their members." ::= { zoneConfiguration 7 } zoneEntry OBJECT-TYPE SYNTAX ZoneEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the zoneTable. The sequence of operations to be performed in order to create a zone is as follows: - create an entry in this table. - create zone members in the zoneMemberTable that belong to this zone. - if aliases need to be created, create an alias entry in the zoneAliasTable, create alias members in the zoneMemberTable and associate the alias with the required zone entry by setting the zoneAliasList object in this table appropriately." INDEX { vsanIndex, zoneIndex } ::= { zoneTable 1 } ZoneEntry ::= SEQUENCE { zoneIndex Unsigned32, zoneName SnmpAdminString, zoneMemberList FcList, zoneAliasList FcList, zoneLastChange TimeStamp, zoneRowStatus RowStatus, zoneReadOnly TruthValue, zoneQos TruthValue, zoneQosPriority ZoneQosPriorityLevel, zoneBroadcast TruthValue, zoneClone SnmpAdminString } zoneIndex OBJECT-TYPE SYNTAX Unsigned32 (1..8192) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of a zone on this VSAN." ::= { zoneEntry 1 } zoneName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..64)) MAX-ACCESS read-create STATUS current DESCRIPTION "The name of this zone. The zoneName should be unique within a VSAN. The zone can be renamed by setting this object to a new value. This object MUST be set before or concurrently with setting the corresponding instance of zoneRowStatus to 'active'." ::= { zoneEntry 2 } zoneMemberList OBJECT-TYPE SYNTAX FcList MAX-ACCESS read-only STATUS current DESCRIPTION "The set of zone members that form this zone on this VSAN. The zone members are identified by zoneMemberIndex object in the zoneMemberTable. If a particular bit has a value of '1', then the corresponding zone member is a part of this zone. All other zone members have '0' in their positions or not present in the string. This object is read-only; changes to its value are made by the agent as and when associated entries are created/deleted in the zoneMemberTable. The default value is the zero length string." DEFVAL { ''H } ::= { zoneEntry 3 } zoneAliasList OBJECT-TYPE SYNTAX FcList MAX-ACCESS read-create STATUS current DESCRIPTION "The set of aliases that form this zone on this VSAN. The aliases are identified by the zoneAliasIndex object in the zoneAliasTable. If a particular bit has a value of '1', then the corresponding alias is a part of this zone. All other aliases have '0' in their positions or not present in the string. The default value is the zero length string." DEFVAL {''H} ::= { zoneEntry 4 } zoneLastChange OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time of the last change to this zone entry. If the entry has not been modified since the last re-initialization of the local network management system, then this object will contain a zero value." ::= { zoneEntry 5 } zoneRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. This object can not be set to 'active' unless the corresponding value of zoneName is unique within the VSAN." ::= { zoneEntry 6 } zoneReadOnly OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates if only SCSI read operations are allowed on the members of this zone which are SCSI targets. If the value of this object is set to 'true', then only SCSI read operations are permitted. So, this becomes a read-only zone. If the value of this object is set to 'false', then both SCSI read and write operations are permitted." DEFVAL { false } ::= { zoneEntry 7 } zoneQos OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies if qos attribute for this zone is enabled. If this object is set to 'true', then qos attribute for this zone is enabled. If this object is set to 'false', then qos attribute for this zone is disabled. If this attribute is enabled for this zone, then only traffic with the configured priority level will be allowed between the members of this zone. The priority can be specified by means of the corresponding instance of zoneQosPriority object." DEFVAL { false } ::= { zoneEntry 8 } zoneQosPriority OBJECT-TYPE SYNTAX ZoneQosPriorityLevel MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the qos priority value. The value of this object is relevant only if the corresponding instance of zoneQos object is enabled by setting it to 'true'." DEFVAL { none } ::= { zoneEntry 9 } zoneBroadcast OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies if broadcast zoning is enabled on this zone. If this object is set to 'true', then it is enabled. If this object is set to 'false', then it is disabled. If broadcast zoning is enabled on this zone, then broadcast frames generated by a member in this zone will be restricted to members in this zone." DEFVAL { false } ::= { zoneEntry 10 } zoneClone OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..64)) MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this object to a name will result in this zone being cloned and the cloned zone will be set to this name. When this object is read, the zero-length string is returned." ::= { zoneEntry 11 } -- -- zoneAliasTable -- zoneAliasNumber OBJECT-TYPE SYNTAX Integer32 (0..8388608) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of entries currently present in the zoneAliasTable." ::= { zoneConfiguration 8 } zoneAliasTable OBJECT-TYPE SYNTAX SEQUENCE OF ZoneAliasEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table gives information on all the aliases and their members." ::= { zoneConfiguration 9 } zoneAliasEntry OBJECT-TYPE SYNTAX ZoneAliasEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in this table." INDEX { vsanIndex, zoneAliasIndex } ::= { zoneAliasTable 1 } ZoneAliasEntry ::= SEQUENCE { zoneAliasIndex Unsigned32, zoneAliasName SnmpAdminString, zoneAliasMemberList FcList, zoneAliasRowStatus RowStatus, zoneAliasLastChange TimeStamp, zoneAliasClone SnmpAdminString } zoneAliasIndex OBJECT-TYPE SYNTAX Unsigned32 (1..2048) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of an alias entry on this VSAN." ::= { zoneAliasEntry 1 } zoneAliasName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..64)) MAX-ACCESS read-create STATUS current DESCRIPTION "The name of this alias. The name of the alias should be unique within a VSAN. The alias can be renamed by setting this object to a new value. This object MUST be set before or concurrently with setting the corresponding instance of zoneAliasRowStatus to 'active'." ::= { zoneAliasEntry 2 } zoneAliasMemberList OBJECT-TYPE SYNTAX FcList MAX-ACCESS read-only STATUS current DESCRIPTION "The set of zone members which form this alias on this VSAN. The members of an alias are identified by the zoneMemberIndex object in the zoneMemberTable. If a particular bit has a value of '1', then the corresponding zone member is a part of this alias. All other zone members have '0' in their positions or not present in the string. This object is read-only; changes to its value are made by the agent as and when associated entries are created/deleted in the zoneMemberTable. The default value is the zero length string." DEFVAL { ''H } ::= { zoneAliasEntry 3 } zoneAliasRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. This object can not be set to 'active' unless the corresponding value of zoneAliasName is unique within the VSAN." ::= { zoneAliasEntry 4 } zoneAliasLastChange OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time of the last change to this alias entry. If the entry has not been modified since the last re-initialization of the local network management system, then this object will contain a zero value." ::= { zoneAliasEntry 5 } zoneAliasClone OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..64)) MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this object to a name will result in this alias being cloned and the cloned alias will be set to this name. When this object is read, the zero-length string is returned." ::= { zoneAliasEntry 6 } -- -- zoneMemberTable -- zoneMemberNumber OBJECT-TYPE SYNTAX Integer32 (0..16777216) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of entries currently present in the zoneMemberTable." ::= { zoneConfiguration 10 } zoneMemberTable OBJECT-TYPE SYNTAX SEQUENCE OF ZoneMemberEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains all members of a zone/alias and information about those members." ::= { zoneConfiguration 11 } zoneMemberEntry OBJECT-TYPE SYNTAX ZoneMemberEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the zoneMemberTable. Each entry represents the relationship between a member and (one of) its 'parent(s)', i.e., a zone or alias to which the member belongs, within a particular VSAN." INDEX { vsanIndex, zoneMemberTypeIndex, zoneMemberParentIndex, zoneMemberIndex } ::= { zoneMemberTable 1 } ZoneMemberEntry ::= SEQUENCE { zoneMemberTypeIndex INTEGER, zoneMemberParentIndex Unsigned32, zoneMemberIndex Unsigned32, zoneMemberFormat ZoneMemberType, zoneMemberID OCTET STRING, zoneMemberLunID OCTET STRING, zoneMemberRowStatus RowStatus } zoneMemberTypeIndex OBJECT-TYPE SYNTAX INTEGER { zone(1), -- member belongs to a zone alias(2) -- member belongs to an alias } MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object determines whether this member belongs to a zone or an alias." ::= { zoneMemberEntry 1 } zoneMemberParentIndex OBJECT-TYPE SYNTAX Unsigned32 (1..8192) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object contains the value of the index of the zone or alias to which this member belongs to. If the value of the corresponding instance of zoneMemberTypeIndex is 'zone', then this object will contain the value of the zoneIndex object of the zone to which this member belongs to. If the value of the corresponding instance of zoneMemberTypeIndex is 'alias', then this object will contain the value of the zoneAliasIndex object of the alias to which this member belongs to." ::= { zoneMemberEntry 2 } zoneMemberIndex OBJECT-TYPE SYNTAX Unsigned32 (1..2048) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of this zone member on this VSAN on this zone/alias." ::= { zoneMemberEntry 3 } zoneMemberFormat OBJECT-TYPE SYNTAX ZoneMemberType MAX-ACCESS read-create STATUS current DESCRIPTION "This object identifies the format of the zone/alias member's identifier contained in zoneMemberID. This object cannot be modified while the corresponding value of zoneMemberRowStatus object is 'active'." ::= { zoneMemberEntry 4 } zoneMemberID OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..255)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the zone/alias member ID. The interpretation of this object depends on the zoneMemberFormat object. If the value of corresponding instance of zoneMemberFormat object is 'wwn', then this object holds an 8 octet long Port WWN. If the value of corresponding instance of zoneMemberFormat object is 'domainPort', then this object contains a 2 octet value. The first octet will represent the domain and the second octet will represent the port. If the value of the corresponding instance of zoneMemberFormat object is 'fcAddr', then this object contains the 3 octet N_Port FC-ID. If the value of the corresponding instance of zoneMemberFormat object is 'fwwn', then this object contains the 8 octet Fabric Port WWN. If the value of the corresponding instance of zoneMemberFormat object is 'symNodeName', then this object contains a symbolic node name which could be of length 1 to 255 bytes. If the value of corresponding instance of zoneMemberFormat object is 'intf', then this object will contain a 12 octet value which is a concatenation of 4 octets containing an interface index (ifIndex) encoded in network byte order, and 8 octets containing the WWN of a switch. If the value of corresponding instance of zoneMemberFormat object is 'domainIntf', then this object will contain a 5 octet value which is a concatenation of 1 octet representing the domain and 4 octets representing an interface index (ifIndex) encoded in network byte order. If the value of corresponding instance of zoneMemberFormat object is 'ipAddr', then this object will contain a 4 octet IP address value followed by an optional 4 octets of subnet mask. If the value of corresponding instance of zoneMemberFormat object is 'ipAddrv6', then this object will contain a 16 octet IPv6 address value followed by an optional 4 octets of prefix length encoded in network byte order. If the value of the corresponding instance of zoneMemberFormat object is 'deviceAlias', then this object contains a Device Alias which could be of length 1 to 64 bytes. This object cannot be modified while the corresponding value of zoneMemberRowStatus object is 'active'." ::= { zoneMemberEntry 5 } zoneMemberLunID OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0 | 8)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the Lun ID if Lun zoning is configured. If this object is the zero-length string, then Lun zoning is not configured. Lun zoning cannot be configured when the corresponding instance of zoneMemberFormat object has a value of 'fwwn', 'intf' or 'symNodeName'. This object cannot be modified while the corresponding value of zoneMemberRowStatus object is 'active'." DEFVAL { ''H } ::= { zoneMemberEntry 6 } zoneMemberRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. zoneMemberID and zoneMemberFormat objects MUST be set before or concurrently with setting the corresponding instance of zoneMemberRowStatus to 'active'. If Lun zoning needs to be configured, then zoneMemberLunID object also needs to be set before or concurrently with setting the corresponding instance of zoneMemberRowStatus to 'active'." ::= { zoneMemberEntry 7 } zoneEnforcedZoneSetNumber OBJECT-TYPE SYNTAX Integer32 (0..2048) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of entries currently present in the zoneEnforcedZoneSetTable." ::= { zoneConfiguration 12 } zoneEnforcedZoneSetTable OBJECT-TYPE SYNTAX SEQUENCE OF ZoneEnforcedZoneSetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing information on all currently enforced zone sets (active zone sets) on all VSANs. Only one zone set can be activated per VSAN. The active zone set is one which is copied from the zone set database (zoneSetTable) at the time it was activated. This active zone set is then enforced on the fabric. This active zone set cannot be modified. Note that this table will be empty when no zone set is activated." ::= { zoneConfiguration 13 } zoneEnforcedZoneSetEntry OBJECT-TYPE SYNTAX ZoneEnforcedZoneSetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the zoneEnforcedZoneSetTable." INDEX { vsanIndex } ::= { zoneEnforcedZoneSetTable 1 } ZoneEnforcedZoneSetEntry ::= SEQUENCE { zoneEnforcedZoneSetName SnmpAdminString, zoneEnforcedZoneSetZoneList FcList, zoneEnforcedZoneSetActivateTime TimeStamp } zoneEnforcedZoneSetName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "The name of this zone set on this VSAN." ::= { zoneEnforcedZoneSetEntry 1 } zoneEnforcedZoneSetZoneList OBJECT-TYPE SYNTAX FcList MAX-ACCESS read-only STATUS current DESCRIPTION "The set of zones which form this zone set on this VSAN. This object was copied from the zoneSetZoneList object in the zoneSetTable at the time when the currently active zone set was activated." ::= { zoneEnforcedZoneSetEntry 2 } zoneEnforcedZoneSetActivateTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The sysUpTime at which this entry was most recently activated. If this entry has been activated prior to the last re-initialization of the local network management system, then this object will contain a zero value." ::= { zoneEnforcedZoneSetEntry 3 } zoneEnforcedZoneNumber OBJECT-TYPE SYNTAX Integer32 (0..8388608) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of entries currently present in the zoneEnforcedZoneTable." ::= { zoneConfiguration 14 } zoneEnforcedZoneTable OBJECT-TYPE SYNTAX SEQUENCE OF ZoneEnforcedZoneEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains all the zones/aliases that are present in the active zone sets on all VSANs." ::= { zoneConfiguration 15 } zoneEnforcedZoneEntry OBJECT-TYPE SYNTAX ZoneEnforcedZoneEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in this table." INDEX { vsanIndex, zoneIndex } ::= { zoneEnforcedZoneTable 1 } ZoneEnforcedZoneEntry ::= SEQUENCE { zoneEnforcedZoneName SnmpAdminString, zoneEnforcedZoneMemberList FcList, zoneEnforcedZoneAliasList FcList, zoneEnforcedZoneActivateTime TimeStamp, zoneEnforcedZoneReadOnly TruthValue, zoneEnforcedZoneQos TruthValue, zoneEnforcedZoneQosPriority ZoneQosPriorityLevel, zoneEnforcedZoneBroadcast TruthValue } zoneEnforcedZoneName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "The name of this zone." ::= { zoneEnforcedZoneEntry 1 } zoneEnforcedZoneMemberList OBJECT-TYPE SYNTAX FcList MAX-ACCESS read-only STATUS current DESCRIPTION "The set of members that form this zone on this VSAN. This object was copied from the zoneMemberList object in the zoneTable at the time when the currently active zone set was activated." ::= { zoneEnforcedZoneEntry 2 } zoneEnforcedZoneAliasList OBJECT-TYPE SYNTAX FcList MAX-ACCESS read-only STATUS current DESCRIPTION "The set of aliases that form this zone on this VSAN. This object was copied from the zoneAliasList object in the zoneTable at the time when the currently active zone set was activated." ::= { zoneEnforcedZoneEntry 3 } zoneEnforcedZoneActivateTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The sysUpTime at which this entry was most recently activated. If this entry has been activated prior to the last re-initialization of the local network management system, then this object will contain a zero value." ::= { zoneEnforcedZoneEntry 4 } zoneEnforcedZoneReadOnly OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether this is a read-only zone. This object was copied from the zoneReadOnly object in the zoneTable at the time when the currently active zone set was activated." ::= { zoneEnforcedZoneEntry 5 } zoneEnforcedZoneQos OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether this is a qos enabled zone. This object was copied from the zoneQos object in the zoneTable at the time when the currently active zone set was activated." ::= { zoneEnforcedZoneEntry 6 } zoneEnforcedZoneQosPriority OBJECT-TYPE SYNTAX ZoneQosPriorityLevel MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the priority of qos if it is a qos enabled zone. This object was copied from the zoneQosPriority object in the zoneTable at the time when the currently active zone set was activated." ::= { zoneEnforcedZoneEntry 7 } zoneEnforcedZoneBroadcast OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether broadcast zoning is enabled. This object was copied from the zoneBroadcast object in the zoneTable at the time when the currently active zone set was activated." ::= { zoneEnforcedZoneEntry 8 } zoneEnforcedZoneAliasNumber OBJECT-TYPE SYNTAX Integer32 (0..8488608) MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of entries currently present in the zoneEnforcedZoneAliasTable." ::= { zoneConfiguration 16 } zoneEnforcedZoneAliasTable OBJECT-TYPE SYNTAX SEQUENCE OF ZoneEnforcedZoneAliasEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "This table contains all the aliases that are a part of active zone sets on all VSANs." ::= { zoneConfiguration 17 } zoneEnforcedZoneAliasEntry OBJECT-TYPE SYNTAX ZoneEnforcedZoneAliasEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "An entry (conceptual row) in this table." INDEX { vsanIndex, zoneAliasIndex } ::= { zoneEnforcedZoneAliasTable 1 } ZoneEnforcedZoneAliasEntry ::= SEQUENCE { zoneEnforcedZoneAliasName SnmpAdminString, zoneEnforcedZoneAliasMemberList FcList } zoneEnforcedZoneAliasName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..64)) MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The name of this alias." ::= { zoneEnforcedZoneAliasEntry 1 } zoneEnforcedZoneAliasMemberList OBJECT-TYPE SYNTAX FcList MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The set of members that form this alias on this VSAN. This object was copied from the zoneAliasMemberList object in the zoneAliasTable at the time when the currently active zone set was activated." ::= { zoneEnforcedZoneAliasEntry 2 } zoneEnforcedZoneMemberNumber OBJECT-TYPE SYNTAX Integer32 (0..16777216) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of entries currently present in the zoneEnforcedZoneMemberTable." ::= { zoneConfiguration 18 } zoneEnforcedZoneMemberTable OBJECT-TYPE SYNTAX SEQUENCE OF ZoneEnforcedZoneMemberEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains all members that are part of a zone/alias and are part of the active zone sets on all VSANs." ::= { zoneConfiguration 19 } zoneEnforcedZoneMemberEntry OBJECT-TYPE SYNTAX ZoneEnforcedZoneMemberEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in this table." INDEX { vsanIndex, zoneMemberTypeIndex, zoneMemberParentIndex, zoneMemberIndex } ::= { zoneEnforcedZoneMemberTable 1 } ZoneEnforcedZoneMemberEntry ::= SEQUENCE { zoneEnforcedZoneMemberFormat ZoneMemberType, zoneEnforcedZoneMemberID OCTET STRING, zoneEnforcedZoneMemberLunID OCTET STRING } zoneEnforcedZoneMemberFormat OBJECT-TYPE SYNTAX ZoneMemberType MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the address format of this member. The address is contained in the corresponding instance of zoneEnforcedZoneMemberID object." ::= { zoneEnforcedZoneMemberEntry 1 } zoneEnforcedZoneMemberID OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents this member's address. This object was copied from the zoneMemberID object in the zoneMemberTable at the time when the currently active zone set was activated." ::= { zoneEnforcedZoneMemberEntry 2 } zoneEnforcedZoneMemberLunID OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0 | 8)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the Lun ID if LUN zoning is configured. This object was copied from the zoneMemberLunID object in the zoneMemberTable at the time when the currently active zone set was activated." ::= { zoneEnforcedZoneMemberEntry 3 } zoneMergeFailRecoverSpinLock OBJECT-TYPE SYNTAX TestAndIncr MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to facilitate modification of zoneMergeFailRecoverInterface, zoneMergeFailRecoverVsan and zoneMergeFailRecoverOper by multiple managers. The procedure for modifying these objects is as follows: 1. Determine new values for zoneMergeFailRecoverInterface, zoneMergeFail- RecoverVsan and zoneMergeFailRecoverOper. 2. Retrieve the value of zoneMergeFailRecoverSpinLock. 3. Set the value of zoneMergeFailRecoverSpinLock to the retrieved value, and (in the same PDU) the value of zoneMergeFailRecoverInterface to the new value. If the set fails for zoneMergeFailRecoverSpinLock object, go back to step 2. 4. Set the value of zoneMergeFailRecoverSpinLock to the retrieved value plus one, and (in the same PDU) the value of zoneMergeFailRecoverVsan to the new value. If the set fails for zoneMergeFailRecoverSpinLock object, go back to step 2. 5. Set the value of zoneMergeFailRecoverSpinLock to the retrieved value plus two, and (in the same PDU) the value of zoneMergeFailRecoverOper to the new value. If the set fails for zoneMergeFailRecoverSpinLock object, go back to step 2. Note that if it's possible to include zoneMergeFailRecoverVsan and/or zoneMergeFailRecoverOper in the (Set Req) PDU of an earlier step, then steps 4 and/or 5 can be eliminated." ::= { zoneConfiguration 20 } zoneMergeFailRecoverInterface OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-write STATUS current DESCRIPTION "The interface on which the Merge Failure Recovery needs to be carried out. The value of this object before the first set operation will be zero." ::= { zoneConfiguration 21 } zoneMergeFailRecoverVsan OBJECT-TYPE SYNTAX VsanIndex MAX-ACCESS read-write STATUS current DESCRIPTION "The VSAN on which the Merge Failure Recovery needs to be carried out." DEFVAL { 1 } ::= { zoneConfiguration 22 } zoneMergeFailRecoverOper OBJECT-TYPE SYNTAX INTEGER { import(1), -- import the active zone set export(2), -- export the active zone set noop(3) -- no operation } MAX-ACCESS read-write STATUS current DESCRIPTION "The operation to be carried out. If this object is set to 'import', then the Active Zone Set from across the isolated link is imported. If this object is set to 'export', then the Active Zone Set on the local system is exported across the isolated link. No action is taken if this object is set to 'noop'. The value of this object when read is always 'noop'." ::= { zoneConfiguration 23 } zoneMergeFailRecoverResult OBJECT-TYPE SYNTAX INTEGER { success(1), -- merge fail recovery successful failure(2), -- merge fail recovery fail inProgress(3) -- recovery in progress } MAX-ACCESS read-only STATUS current DESCRIPTION "The result of the last Merge Failure Recovery operation that was attempted. If the value of this object is 'success', then the merge fail recovery operation was successful. If the value of this object is 'failure', then the merge fail recovery operation failed. If the value of this object is 'inProgress', then the merge fail recovery operation is still in progress." ::= { zoneConfiguration 24 } zoneCopyActiveToFullOnVsan OBJECT-TYPE SYNTAX VsanIndex MAX-ACCESS read-write STATUS deprecated -- This object has been deprecated because in -- addition to setting the VSAN on which the -- copy has to take place, a mode also has -- been introduced. The objects to be used -- are zoneCopyActToFullSpinLock, -- zoneCopyActToFullMode and zoneCopyActToFullVsan. DESCRIPTION "The VSAN on which the enforced zone set (active zone set) needs to be copied to the zone set database (full zone set). Setting this object to a valid VSAN will trigger a copy of the enforced zone set on that VSAN to the zone set database on the same VSAN. Setting this object to an invalid VSAN-id will result in an error and no copy will take place." ::= { zoneConfiguration 25 } -- Zone Server Statistics zoneTotalGS3Rejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of GS3 requests rejected by this Zone Server across all VSANs." ::= { zoneStats 1 } zoneStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF ZoneStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains statistic counters which are maintained by the Zone Server. These counters are maintained per VSAN." ::= { zoneStats 2 } zoneStatsEntry OBJECT-TYPE SYNTAX ZoneStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in this table." INDEX { vsanIndex } ::= { zoneStatsTable 1 } ZoneStatsEntry ::= SEQUENCE { zoneTxMergeReqs Counter32, zoneRxMergeAccepts Counter32, zoneRxMergeReqs Counter32, zoneTxMergeAccepts Counter32, zoneTxChangeReqs Counter32, zoneRxChangeAccepts Counter32, zoneRxChangeReqs Counter32, zoneTxChangeAccepts Counter32, zoneRxGS3Reqs Counter32, zoneTxGS3Rejects Counter32 } zoneTxMergeReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Merge Request Frames sent by this Zone Server to other Zone Servers in the fabric on this VSAN." ::= { zoneStatsEntry 1 } zoneRxMergeAccepts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Merge Accept Frames received by this Zone Server from other Zone Servers in the fabric on this VSAN." ::= { zoneStatsEntry 2 } zoneRxMergeReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Merge Request Frames received by this Zone Server from other Zone Servers in the fabric on this VSAN." ::= { zoneStatsEntry 3 } zoneTxMergeAccepts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Merge Accept Frames sent by this Zone Server to other Zone Servers in the fabric on this VSAN." ::= { zoneStatsEntry 4 } zoneTxChangeReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Change Requests sent by this Zone Server to other Zone Servers in the fabric on this VSAN. This includes Acquire Change Authorization requests, Stage Fabric Config Update requests, Update Fabric Config requests and Release Change Authorization requests." ::= { zoneStatsEntry 5 } zoneRxChangeAccepts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Change Responses received by this Zone Server from other Zone Servers in the fabric on this VSAN. This includes Acquire Change Authorization Accept, Stage Fabric Config Update Accept, Update Fabric Config Accept and Release Change Authorization Accept frames." ::= { zoneStatsEntry 6 } zoneRxChangeReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Change Requests received by this Zone Server from other Zone Servers in the fabric on this VSAN. This includes Acquire Change Authorization requests, Stage Fabric Config Update requests, Update Fabric Config requests and Release Change Authorization requests." ::= { zoneStatsEntry 7 } zoneTxChangeAccepts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Change Responses sent by this Zone Server to other Zone Servers in the fabric on this VSAN. This includes Acquire Change Authorization Accept, Stage Fabric Config Update Accept, Update Fabric Config Accept and Release Change Authorization Accept frames." ::= { zoneStatsEntry 8 } zoneRxGS3Reqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of GS3 requests received by this Zone Server on this VSAN." ::= { zoneStatsEntry 9 } zoneTxGS3Rejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of GS3 requests rejected by this Zone Server on this VSAN." ::= { zoneStatsEntry 10 } zoneLunStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF ZoneLunStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains statistic counters related to LUNs. These counters are populated by the local Zone Server based on SCSI frames that are forwarded to it because the LUNs being accessed have been zoned out from a initiator's list of accessible LUNs. These counters are maintained per VSAN, per SCSI initiator-target pair, per LUN." ::= { zoneStats 3 } zoneLunStatsEntry OBJECT-TYPE SYNTAX ZoneLunStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry provides SCSI statistics, at the local Zone Server, for the host identified by zoneLunSrcFcId trying to access the LUN identified by zoneLunNum, that has been zoned out from zoneLunSrcFcId's list of accessible LUNs, on the disk identified by zoneLunDstFcId on the VSAN identified by vsanIndex." INDEX { vsanIndex, zoneLunSrcFcId, zoneLunDstFcId, zoneLunNum } ::= { zoneLunStatsTable 1 } ZoneLunStatsEntry ::= SEQUENCE { zoneLunSrcFcId FcAddressId, zoneLunDstFcId FcAddressId, zoneLunNum OCTET STRING, zoneLunRxInqReqs Counter32, zoneLunRxRepLunReqs Counter32, zoneLunRxSenseReqs Counter32, zoneLunRxOtherCmds Counter32, zoneLunTxInqDataNoLus Counter32, zoneLunTxIllegalReqs Counter32 } zoneLunSrcFcId OBJECT-TYPE SYNTAX FcAddressId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The FC-ID of a SCSI initiator that is accessing a LUN identified by zoneLunNum." ::= { zoneLunStatsEntry 1 } zoneLunDstFcId OBJECT-TYPE SYNTAX FcAddressId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The FC-ID of a SCSI target containing the LUN identified by zoneLunNum." ::= { zoneLunStatsEntry 2 } zoneLunNum OBJECT-TYPE SYNTAX OCTET STRING (SIZE(8)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The LUN that is being accessed." ::= { zoneLunStatsEntry 3 } zoneLunRxInqReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of SCSI INQUIRY commands that have been received by the local Zone Server from the SCSI initiator zoneLunSrcFcId to the SCSI target zoneLunDstFcId for the LUN zoneLunNum, on the VSAN vsanIndex." REFERENCE "Section 7.4 INQUIRY command. SCSI Primary Commands- 3 (SPC-3)" ::= { zoneLunStatsEntry 4 } zoneLunRxRepLunReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of SCSI Report LUNs commands that have been received by the local Zone Server from the SCSI initiator zoneLunSrcFcId to the SCSI target zoneLunDstFcId for the LUN zoneLunNum, on the VSAN vsanIndex. Typically the Report LUNs command is sent only for LUN 0." REFERENCE "Section 7.22 REPORT LUNS command. SCSI Primary Commands- 3 (SPC-3)" ::= { zoneLunStatsEntry 5 } zoneLunRxSenseReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of SCSI SENSE commands that have been received by the local Zone Server from the SCSI initiator zoneLunSrcFcId to the SCSI target zoneLunDstFcId for the LUN zoneLunNum, on the VSAN vsanIndex." REFERENCE "Section 7.25 REQUEST SENSE command. SCSI Primary Commands- 3 (SPC-3)" ::= { zoneLunStatsEntry 6 } zoneLunRxOtherCmds OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of SCSI Read, Write, Seek etc. commands received by the local Zone Server from the SCSI initiator zoneLunSrcFcId to the SCSI target zoneLunDstFcId for the LUN zoneLunNum, on the VSAN vsanIndex, during changes to the zoning configuration." ::= { zoneLunStatsEntry 7 } zoneLunTxInqDataNoLus OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of 'No LU' error responses sent by the local Zone Server in response to SCSI INQUIRY commands from the SCSI initiator zoneLunSrcFcId to the SCSI target zoneLunDstFcId for the LUN zoneLunNum, on the VSAN vsanIndex." REFERENCE "Section 5.9.3 Incorrect Logical Unit Selection SCSI Architectural Model- 2 (SAM-2)" ::= { zoneLunStatsEntry 8 } zoneLunTxIllegalReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of 'Illegal Request Check Condition' responses sent by the local Zone Server in response to SCSI commands from the SCSI initiator zoneLunSrcFcId to the SCSI target zoneLunDstFcId for the LUN zoneLunNum, on the VSAN vsanIndex." REFERENCE "Section 5.9.3 Incorrect Logical Unit Selection SCSI Architectural Model- 2 (SAM-2)" ::= { zoneLunStatsEntry 9 } zoneRoZoneStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF ZoneRoZoneStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains statistic counter(s) related to read-only zones which are maintained by the Zone Server. These counters are maintained per VSAN, per SCSI initiator target pair, per LUN." ::= { zoneStats 4 } zoneRoZoneStatsEntry OBJECT-TYPE SYNTAX ZoneRoZoneStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry provides statistics for the host identified by zoneRoZoneSrcFcId accessing the LUN identified by zoneRoZoneLunNum on the disk identified by zoneRoZoneDstFcId on the VSAN identified by vsanIndex." INDEX { vsanIndex, zoneRoZoneSrcFcId, zoneRoZoneDstFcId, zoneRoZoneLunNum } ::= { zoneRoZoneStatsTable 1 } ZoneRoZoneStatsEntry ::= SEQUENCE { zoneRoZoneSrcFcId FcAddressId, zoneRoZoneDstFcId FcAddressId, zoneRoZoneLunNum OCTET STRING, zoneRoZoneTxDataProts Counter32 } zoneRoZoneSrcFcId OBJECT-TYPE SYNTAX FcAddressId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The FC-ID of a SCSI initiator that is accessing a LUN identified by zoneRoZoneLunNum." ::= { zoneRoZoneStatsEntry 1 } zoneRoZoneDstFcId OBJECT-TYPE SYNTAX FcAddressId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The FC-ID of a SCSI target containing the LUN identified by zoneRoZoneLunNum." ::= { zoneRoZoneStatsEntry 2 } zoneRoZoneLunNum OBJECT-TYPE SYNTAX OCTET STRING (SIZE(8)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The LUN that is being accessed." ::= { zoneRoZoneStatsEntry 3 } zoneRoZoneTxDataProts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of 'Data protected Check Condition' error responses sent by the local Zone Server, when the SCSI initiator identified by zoneRoZoneSrcFcId tries to modify a LUN identified by zoneRoZoneLunNum on the SCSI target zoneRoZoneDstFcId." REFERENCE "Section 5.1.13 Error Reporting, SCSI-3 Block Commands (SBC)" ::= { zoneRoZoneStatsEntry 4 } -- Notification information zoneServiceRejReasonCode OBJECT-TYPE SYNTAX FcGs3RejectReasonCode MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the reason code corresponding to the latest Zone Server request rejection." ::= { zoneInformation 1 } zoneServiceRejReasonCodeExp OBJECT-TYPE SYNTAX FcZoneServerRejReasonExpl MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the reason code explanation if the reason code is 'Unable to perform command req'. This object also corresponds to the latest Zone Server request rejection." ::= { zoneInformation 2 } zoneMergeFailureVSANNum OBJECT-TYPE SYNTAX Unsigned32 (0..4096) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the number of the VSAN on an interface on which the last zone merge failed. If the zone merge has failed on all VSANs, then this object will contain the value of 0." ::= { zoneInformation 3 } zoneMergeSuccessVSANNum OBJECT-TYPE SYNTAX Unsigned32 (0..4096) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the number of the VSAN on an interface on which the last zone merge succeeded. If the zone merge has succeeded on all VSANs, then this object will contain the value of 0." ::= { zoneInformation 4 } zoneMergeFailureObject OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object contains the name of the zoning database object which was the cause of the merge failure. In cases where it is not applicable, this object will contain the null string." ::= { zoneInformation 5 } zoneMergeFailureReason OBJECT-TYPE SYNTAX ZoneMergeFailCause MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object contains the reason for the the merge failure." ::= { zoneInformation 6 } -- Notification control objects zoneServiceReqRejNotifyEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies if the Zone Server should issue a 'zoneServiceReqRejNotify' notification. If the value of this object is 'true', then the notification is issued. If the value of this object is 'false', then the notification is not issued." ::= { zoneConfiguration 26 } zoneMergeFailureNotifyEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies if the zone server should issue a zoneMergeFailureNotify notification. If the value of this object is 'true', then the notification is issued. If the value of this object is 'false', then the notification is not issued." ::= { zoneConfiguration 27 } zoneMergeSuccessNotifyEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies if the zone server should issue a zoneMergeSuccessNotify notification. If the value of this object is 'true', then the notification is issued. If the value of this object is 'false', then the notification is not issued." ::= { zoneConfiguration 28 } zoneDefZoneBehvrChngNotifyEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies if the zone server should issue a zoneDefZoneBehaviourChngNotify notification. If the value of this object is 'true', then the notification is issued. If the value of this object is 'false', then the notification is not issued." ::= { zoneConfiguration 29 } -- Objects to perform Zone Server DB operations zoneDbTable OBJECT-TYPE SYNTAX SEQUENCE OF ZoneDbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one entry for each VSAN that is configured. These entries provide the capability to perform operations on the local zone server database on a VSAN." ::= { zoneConfiguration 30 } zoneDbEntry OBJECT-TYPE SYNTAX ZoneDbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in this table." INDEX { vsanIndex } ::= { zoneDbTable 1 } ZoneDbEntry ::= SEQUENCE { zoneDbClearDb INTEGER, zoneDbEnforcedEqualsLocal TruthValue, zoneDbHardZoningEnabled TruthValue } zoneDbClearDb OBJECT-TYPE SYNTAX INTEGER { clear(1), noop(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to 'clear(1)', will result in the local zone server database being deleted on this VSAN. Setting this object to 'noop(2)', results in no action. When read, the value of this object is always 'noop(2)'." ::= { zoneDbEntry 1 } zoneDbEnforcedEqualsLocal OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates if the enforced database is the same as the local database on this VSAN. If the value of this object is 'true', then they are the same. If the value of this object is 'false', then they are not the same." ::= { zoneDbEntry 2 } zoneDbHardZoningEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates if hard zoning is enabled on this VSAN. Hard Zoning is a mechanism by which zoning is enforced in hardware. If the value of this object is 'true', then hard zoning is enabled on this VSAN. If the value of this object is 'false', then hard zoning is not enabled on this VSAN." ::= { zoneDbEntry 3 } zoneCopyTable OBJECT-TYPE SYNTAX SEQUENCE OF ZoneCopyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "In this table, for each VSAN that is configured, atmost one entry can be created. These entries provide the capability to copy the active zone set on a VSAN to a file on the local device and/or to a remote device over the network. At any point of time, only one copy operation can be active for all the VSANs. If a second copy is attempted, it will result in error." ::= { zoneConfiguration 31 } zoneCopyEntry OBJECT-TYPE SYNTAX ZoneCopyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in this table." INDEX { vsanIndex } ::= { zoneCopyTable 1 } ZoneCopyEntry ::= SEQUENCE { zoneCopyProto ZoneCopyProtocol, zoneCopyDestFileType ZoneFileType, zoneCopyServerAddrType InetAddressType, zoneCopyServerAddr InetAddress, zoneCopyDestFileName SnmpAdminString, zoneCopyUserName SnmpAdminString, zoneCopyUserPassword SnmpAdminString, zoneCopyStartCopy INTEGER, zoneCopyState INTEGER, zoneCopyRowStatus RowStatus } zoneCopyProto OBJECT-TYPE SYNTAX ZoneCopyProtocol MAX-ACCESS read-create STATUS current DESCRIPTION "The protocol to be used for the copy of the active zone set on this VSAN. If the copy needs to take place on the local device, then the value of this object will be ignored." DEFVAL { tftp } ::= { zoneCopyEntry 1 } zoneCopyDestFileType OBJECT-TYPE SYNTAX ZoneFileType MAX-ACCESS read-create STATUS current DESCRIPTION "The type of file to which the active zoneset needs to be copied. If the value of this object is set to 'networkFile(1)', then values must be set for the corresponding instances of zoneCopyServerAddr and zoneCopyDestFileName objects. If the value of this object is set to 'localFile(2)', then the corresponding instance of zoneCopyDestFileName must be set." DEFVAL { localFile } ::= { zoneCopyEntry 2 } zoneCopyServerAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "The type of address of the remote device as specified by the corresponding instance of zoneCopyServerAddr object." DEFVAL { ipv4 } ::= { zoneCopyEntry 3 } zoneCopyServerAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The ip address of the remote device to which the active zoneset on this VSAN needs to be copied. This object must be set to a valid value when the corresponding instance of zoneCopyDestFileType is set to 'networkFile' before the copy can be initiated by means of the zoneCopyStartCopy object. The protocol to be used for the copy operation is specified by the value of the corresponding instance of zoneCopyProto object." ::= { zoneCopyEntry 4 } zoneCopyDestFileName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..255)) MAX-ACCESS read-create STATUS current DESCRIPTION "The file-name, including the full path, of the file to which the active zoneset on this VSAN needs to be copied. This object must be set to a valid value before the copy can be initiated by means of the zoneCopyStartCopy object." ::= { zoneCopyEntry 5 } zoneCopyUserName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The user name on the remote device onto which the active zoneset on this VSAN needs to be copied. This object needs to be set only if the value of the corresponding instance of zoneCopyDestFileType object is 'networkFile'." ::= { zoneCopyEntry 6 } zoneCopyUserPassword OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The password corresponding to the user name specified by zoneCopyUserName object on the remote device. This object is meaningful only if the corresponding instance of zoneCopyDestFileType object is 'networkFile' and the protocol to be used as specified by zoneCopyProto is 'ftp' or 'sftp' or 'scp'. The value of this object when read is always the zero length string for security reasons." ::= { zoneCopyEntry 7 } zoneCopyStartCopy OBJECT-TYPE SYNTAX INTEGER { copy(1), noop(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object provides the capability to start the copy operation of the active zoneset on this VSAN to the desired destination. When set to 'copy(1)', the copy of the active zoneset on this VSAN is started. No action is taken if this object is set to 'noop(2)'. The value of this object when read is always 'noop'." ::= { zoneCopyEntry 8 } zoneCopyState OBJECT-TYPE SYNTAX INTEGER { success(1), timeout(2), badFileName(3), inProgress(4), badUserNamePasswd(5), incompleteConfig(6), unknown(7), sysErr(8), anotherCopyInProgress(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "The result of the most recent copy operation on this VSAN. success(1) - indicates that the copy operation was successful. timeout(2) - indicates that the copy operation failed due to a timeout. badFileName(3) - indicates that the file name/ path/permissions are incorrect. inProgress(4) - indicates that this copy operation is currently in progress. badUserNamePasswd(5) - indicates that the user name/password of the remote device is incorrect. incompleteConfig(6) - configuration is incomplete. unknown(7) - error is unknown. sysErr(8) - system error anotherCopyInProgress(9) - indicates that a copy operation on the same VSAN or another VSAN is already in progress." ::= { zoneCopyEntry 9 } zoneCopyRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row." ::= { zoneCopyEntry 10 } -- Notification control object (continued) zoneUnsuppMemInIntOpNotifyEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies if the zone server should issue a zoneUnsuppMemInIntOpModeNotify notification. If the value of this object is 'true', then the notification is issued. If the value of this object is 'false', then the notification is not issued." DEFVAL { false } ::= { zoneConfiguration 32 } zoneVsanId OBJECT-TYPE SYNTAX VsanIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the VSAN id on which a mismatch between the operating mode of the local switch and the type of zone members has been detected." ::= { zoneConfiguration 33 } zoneZoneSetDistributeVsan OBJECT-TYPE SYNTAX VsanIndex MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the VSAN on which the full zoneset information needs to be distributed throughout the fabric. Setting this object to a valid VSAN will trigger such an operation. Setting this object to an invalid VSAN will result in an error and no action will be taken. It is to be noted that this operation of full zoneset distribution on this VSAN is done immediately and this is independent of activation/deactivation. This is supported only in 'interop' modes 2 and 3. When a full zoneset distribute operation is in process on a VSAN, any attempt to start the same on another VSAN will result in error." ::= { zoneConfiguration 34 } zoneZoneSetDistributeResult OBJECT-TYPE SYNTAX INTEGER { success(1), failure(2), inProgress(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The outcome of the full zoneset distribute operation on the VSAN indicated by zoneZoneSetDistributeVsan object." ::= { zoneConfiguration 35 } zoneZoneSetDistributeFailReason OBJECT-TYPE SYNTAX FcChangeProtoFailCause MAX-ACCESS read-only STATUS current DESCRIPTION "If the outcome of distributing the full zoneset on a VSAN is failure, then this object will contain the reason for the failure. In other cases, the value of this object does not make sense." ::= { zoneConfiguration 36 } zoneSwitchWwn OBJECT-TYPE SYNTAX FcNameId MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the WWN of the local device. It is used in the notification zoneActivateNotify." ::= { zoneConfiguration 37 } zoneSetZoneListTable OBJECT-TYPE SYNTAX SEQUENCE OF ZoneSetZoneListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is an extension to the zoneSetTable defined above. The object zoneSetZoneList in zoneSetTable represents the set of zones that form a zoneset. However, this object has the limitation of being able to represent only 2048 zones. This table which extends the zoneSetTable overcomes this limitation and the number of zones that form a zoneset is increased to 8192." ::= { zoneConfiguration 38 } zoneSetZoneListEntry OBJECT-TYPE SYNTAX ZoneSetZoneListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in this table represents a set of 6144 zones that can be associated with the zoneset represented by zoneSetIndex on VSAN represented by vsanIndex." AUGMENTS { zoneSetEntry } ::= { zoneSetZoneListTable 1 } ZoneSetZoneListEntry ::= SEQUENCE { zoneSetZoneListBmap4k FcList, zoneSetZoneListBmap6k FcList, zoneSetZoneListBmap8k FcList } zoneSetZoneListBmap4k OBJECT-TYPE SYNTAX FcList MAX-ACCESS read-create STATUS current DESCRIPTION "The set of zones from ids 2049 to 4096 which form this zone set on this VSAN. The zones are identified by zoneIndex object in the zoneTable. If a particular bit has a value of '1', then the corresponding zone is a part of this zone set. All other zones have '0' in their positions or not present in the string. The default value is the zero length string." DEFVAL { ''H } ::= { zoneSetZoneListEntry 1 } zoneSetZoneListBmap6k OBJECT-TYPE SYNTAX FcList MAX-ACCESS read-create STATUS current DESCRIPTION "The set of zones from ids 4097 to 6144 which form this zone set on this VSAN. The zones are identified by zoneIndex object in the zoneTable. If a particular bit has a value of '1', then the corresponding zone is a part of this zone set. All other zones have '0' in their positions or not present in the string. The default value is the zero length string." DEFVAL { ''H } ::= { zoneSetZoneListEntry 2 } zoneSetZoneListBmap8k OBJECT-TYPE SYNTAX FcList MAX-ACCESS read-create STATUS current DESCRIPTION "The set of zones from ids 6145 to 8192 which form this zone set on this VSAN. The zones are identified by zoneIndex object in the zoneTable. If a particular bit has a value of '1', then the corresponding zone is a part of this zone set. All other zones have '0' in their positions or not present in the string. The default value is the zero length string." DEFVAL { ''H } ::= { zoneSetZoneListEntry 3 } zoneSetEnforcedZoneListTable OBJECT-TYPE SYNTAX SEQUENCE OF ZoneSetEnforcedZoneListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is an extension to the zoneEnforcedZoneSetTable defined above. The object zoneEnforcedZoneSetZoneList in zoneEnforcedZoneSetTable represents the set of enforced zones that form an enforced zoneset. However, this object has the limitation of being able to represent only 2048 zones. This table which extends the zoneEnforcedZoneSetTable overcomes this limitation and the number of enforced zones that form an enforced zoneset is increased to 8192." ::= { zoneConfiguration 39 } zoneSetEnforcedZoneListEntry OBJECT-TYPE SYNTAX ZoneSetEnforcedZoneListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in this table represents a set of upto 6144 enforced zones that can be associated with the enforced zoneset on VSAN represented by vsanIndex." AUGMENTS { zoneEnforcedZoneSetEntry } ::= { zoneSetEnforcedZoneListTable 1 } ZoneSetEnforcedZoneListEntry ::= SEQUENCE { zoneSetEnforcedZoneListBmap4k FcList, zoneSetEnforcedZoneListBmap6k FcList, zoneSetEnforcedZoneListBmap8k FcList } zoneSetEnforcedZoneListBmap4k OBJECT-TYPE SYNTAX FcList MAX-ACCESS read-only STATUS current DESCRIPTION "The set of zones from ids 2049 to 4096 which form the enforced zone set on this VSAN. The enforced zones are identified by zoneIndex object in the zoneEnforcedZoneTable. If a particular bit has a value of '1', then the corresponding zone is a part of this zone set. All other zones have '0' in their positions or not present in the string." ::= { zoneSetEnforcedZoneListEntry 1 } zoneSetEnforcedZoneListBmap6k OBJECT-TYPE SYNTAX FcList MAX-ACCESS read-only STATUS current DESCRIPTION "The set of zones from ids 4097 to 6144 which form the enforced zone set on this VSAN. The enforced zones are identified by zoneIndex object in the zoneEnforcedZoneTable. If a particular bit has a value of '1', then the corresponding zone is a part of this zone set. All other zones have '0' in their positions or not present in the string." ::= { zoneSetEnforcedZoneListEntry 2 } zoneSetEnforcedZoneListBmap8k OBJECT-TYPE SYNTAX FcList MAX-ACCESS read-only STATUS current DESCRIPTION "The set of zones from ids 6145 to 8192 which form the enforced zone set on this VSAN. The enforced zones are identified by zoneIndex object in the zoneEnforcedZoneTable. If a particular bit has a value of '1', then the corresponding zone is a part of this zone set. All other zones have '0' in their positions or not present in the string." ::= { zoneSetEnforcedZoneListEntry 3 } zoneCompactTable OBJECT-TYPE SYNTAX SEQUENCE OF ZoneCompactEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The zoneSetZoneList object and the zoneSetZoneListTable allow upto 8192 zones to be associated with a zoneset. This is done with the help of 4 bitmaps each of which represent 2048 zones. There may exist a situation where the 'lowest' bitmap may not be fully populated but 'higher' bitmaps may have bits set in them. Semantically what this means is: the lowest 2048 zones have not been fully associated, but zones with higher ids have been associated. This kind of a situation causes problems for management stations which are only aware of older versions of this MIB. They are only aware of zoneSetZoneList object and hence only the 'lowest' 2048 zones that are associated with a zoneset. In the above situation, the total number of zones associated with the zoneset could be less than 2048. But by virtue of being distributed in the 'higher' bitmaps, those zones will not be seen by those management stations as they are not aware of the new objects in zoneSetZoneListTable. In such a situation, a management station which is aware of this version of the MIB, can choose to compact the zones associated with zonesets on a VSAN, so that the holes in the lowest 2048 zones are filled. Note that this table facilitates compaction of only the first 2048 zones and not zones belonging to 'higher' bitmaps." ::= { zoneConfiguration 40 } zoneCompactEntry OBJECT-TYPE SYNTAX ZoneCompactEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry allows compaction to be carried out on a VSAN." INDEX { vsanIndex } ::= { zoneCompactTable 1 } ZoneCompactEntry ::= SEQUENCE { zoneCompactFirst2k INTEGER } zoneCompactFirst2k OBJECT-TYPE SYNTAX INTEGER { compact(1), noop(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to 'compact' will result in compaction of the lowest 2048 zones that are associated to zonesets on this VSAN. Zones present in higher bitmaps will be moved down so that the holes in the lowest 2048 zones are filled. As a result of this, the ids of the corresponding zones are changed and a management station should re-read the zoneTable. If such a compaction is not possible or the lowest 2048 zones are already compacted, the SET operation will result in error. If a compaction operation goes through successfully, then the notification zoneCompactNotify is generated. Setting this object to 'noop', will result in no action being taken. The value of this object when read is always 'noop'." ::= { zoneCompactEntry 1 } zoneCompactVsan OBJECT-TYPE SYNTAX VsanIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the VSAN on which a successful zone compaction has taken place. It is used in the notification zoneCompactNotify." ::= { zoneConfiguration 41 } zoneCopyActToFullSpinLock OBJECT-TYPE SYNTAX TestAndIncr MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to facilitate modification of zoneCopyActToFullMode and zoneCopyActToFullOnVsan by multiple managers. The procedure for modifying these objects is as follows: 1. Determine new values for zoneCopyActToFullMode, zoneCopyActToFullOnVsan. 2. Retrieve the value of zoneCopyActToFullSpinLock. 3. Set the value of zoneCopyActToFullSpinLock to the retrieved value, and (in the same PDU) the value of zoneCopyActToFullMode to the new value. If the set fails for zoneCopyActToFullSpinLock, go back to step 2. 4. Set the value of zoneCopyActToFullSpinLock to the retrieved value plus one, and (in the same PDU) the value of zoneCopyActToFullOnVsan to the new value. If the set fails for zoneCopyActToFullSpinLock object, go back to step 2. Note that if it's possible to include zoneCopyActToFullOnVsan in the (Set Req) PDU of the earlier step, then step 4 can be eliminated." ::= { zoneConfiguration 42 } zoneCopyActToFullMode OBJECT-TYPE SYNTAX INTEGER { includeAutoZones(1), excludeAutoZones(2), noop(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to 'includeAutoZones', results in certain internal zones created by Zone Server being copied along with the enforced database to the full zoneset database. Setting this object to 'excludeAutoZones', does not copy those zones. Setting this object to 'noop' results in no action being taken. The value of this object when read is always 'noop'." ::= { zoneConfiguration 43 } zoneCopyActToFullVsan OBJECT-TYPE SYNTAX VsanIndex MAX-ACCESS read-write STATUS current DESCRIPTION "The VSAN on which the enforced zone set (active zone set) needs to be copied to the zone set database (full zone set). Setting this object to a valid VSAN will trigger a copy of the enforced zone set on that VSAN to the zone set database on the same VSAN. Setting this object to an invalid VSAN-id will result in an error and no copy will take place." ::= { zoneConfiguration 44 } -- Notifications zoneServiceReqRejNotify NOTIFICATION-TYPE OBJECTS { zoneMemberFormat, zoneMemberID, zoneServiceRejReasonCode, zoneServiceRejReasonCodeExp } STATUS current DESCRIPTION "This notification is generated whenever the local Zone Server rejects a registration request. The Zone Server should update the zoneServiceRejReasonCode and zoneServiceRejReason- CodeExp objects with the corresponding reason code and reason code explanation before sending the notification. The zoneMemberType and zoneMemberID identify the source of the request." ::= { zoneNotifications 1 } zoneMergeFailureNotify NOTIFICATION-TYPE OBJECTS { ifIndex, zoneMergeFailureVSANNum, zoneMergeFailureObject, zoneMergeFailureReason } STATUS current DESCRIPTION "This notification is generated whenever there is a zone merge failure. If all VSANs on a link have a zone-merge failure at the same time, then just one notification is generated in which zoneMergeFailureVSANNum object has a zero value. The zoneMergeFailureObject and zoneMergeFailureReason assist in providing information regarding the point of merge failure." ::= { zoneNotifications 2 } zoneMergeSuccessNotify NOTIFICATION-TYPE OBJECTS { ifIndex, zoneMergeSuccessVSANNum } STATUS current DESCRIPTION "This notification is generated whenever a zone merge happens successfully. If all VSANs on a link have a zone-merge success at the same time, then just one notification is generated in which zoneMergeSuccessVSANNum object has a zero value." ::= { zoneNotifications 3 } zoneDefZoneBehaviourChngNotify NOTIFICATION-TYPE OBJECTS { zoneDefaultZoneBehaviour } STATUS current DESCRIPTION "This notification is generated whenever the value of zoneDefaultZoneBehaviour changes." ::= { zoneNotifications 4 } zoneUnsuppMemInIntOpModeNotify NOTIFICATION-TYPE OBJECTS { zoneVsanId } STATUS current DESCRIPTION "This notification is generated whenever one or more zone members are not supported in the mode in which the local switch is currently configured to function. The switch can be configured to operate in certain 'interoperable' modes on a VSAN basis to enable it to work with switches from other vendors. The zoneVsanId object identifies the VSAN on which the mismatch has been identified." ::= { zoneNotifications 5 } zoneActivateNotify NOTIFICATION-TYPE OBJECTS { zoneSetActivateResult, zoneSwitchWwn } STATUS current DESCRIPTION "This notification is generated whenever a zone set is activated/deactivated on a VSAN. The zoneSetActivateResult object denotes the outcome of the activation/deactivation. The zoneSwitchWwn object represents the WWN of the local device." ::= { zoneNotifications 6 } zoneCompactNotify NOTIFICATION-TYPE OBJECTS { zoneCompactVsan } STATUS current DESCRIPTION "This notification is generated whenever a zone compaction on the VSAN specified by zoneCompactVsan happens successfully." ::= { zoneNotifications 7 } -- Conformance zoneServerMIBCompliances OBJECT IDENTIFIER ::= { zoneServerMIBConformance 1 } zoneServerMIBGroups OBJECT IDENTIFIER ::= { zoneServerMIBConformance 2 } zoneServerMIBCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for entities which implement the Zone Server." MODULE MANDATORY-GROUPS {zoneConfigurationGroup, zoneStatisticsGroup, zoneNotificationControlGroup, zoneNotificationGroup} OBJECT zoneSetRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneSetActivateRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneAliasRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneMemberRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." ::= { zoneServerMIBCompliances 1 } zoneServerMIBCompliance1 MODULE-COMPLIANCE STATUS deprecated -- superceded by zoneServerMIBComplianceRev2 DESCRIPTION "The compliance statement for entities which implement the Zone Server." MODULE MANDATORY-GROUPS {zoneConfigurationGroup1, zoneStatisticsGroup, zoneNotificationControlGroup, zoneNotificationGroup} OBJECT zoneSetRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneSetActivateRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneAliasRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneMemberRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." ::= { zoneServerMIBCompliances 2 } zoneServerMIBComplianceRev2 MODULE-COMPLIANCE STATUS deprecated -- superceded by zoneServerMIBComplianceRev3 DESCRIPTION "The compliance statement for entities which implement the Zone Server." MODULE MANDATORY-GROUPS {zoneConfigurationGroup2, zoneStatisticsGroup, zoneNotificationControlGroup, zoneNotificationGroup} GROUP zoneLunStatsGroup DESCRIPTION "Only entities that support LUN zoning need to support this group." OBJECT zoneSetRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneSetActivateRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneAliasRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneMemberRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." ::= { zoneServerMIBCompliances 3 } zoneServerMIBComplianceRev3 MODULE-COMPLIANCE STATUS deprecated -- superceded by zoneServerMIBComplianceRev4 DESCRIPTION "The compliance statement for entities which implement the Zone Server." MODULE MANDATORY-GROUPS {zoneConfigurationGroup3, zoneStatisticsGroup, zoneNotificationControlGroup, zoneNotificationGroup} GROUP zoneLunStatsGroup DESCRIPTION "Only entities that support LUN zoning need to support this group." OBJECT zoneSetRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneSetActivateRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneAliasRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneMemberRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneCopyRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneCopyServerAddrType SYNTAX INTEGER { ipv4(1) } DESCRIPTION "Only IPv4 support is required." ::= { zoneServerMIBCompliances 4 } zoneServerMIBComplianceRev4 MODULE-COMPLIANCE STATUS deprecated -- deprecated by zoneServerMIBComplianceRev5 DESCRIPTION "The compliance statement for entities which implement the Zone Server." MODULE MANDATORY-GROUPS {zoneConfigurationGroup3, zoneStatisticsGroup, zoneNotificationControlGroup1, zoneNotificationGroup1} GROUP zoneLunStatsGroup DESCRIPTION "Only entities that support LUN zoning need to support this group." OBJECT zoneSetRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneSetActivateRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneAliasRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneMemberRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneCopyRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneCopyServerAddrType SYNTAX INTEGER { ipv4(1) } DESCRIPTION "Only IPv4 support is required." ::= { zoneServerMIBCompliances 5 } zoneServerMIBComplianceRev5 MODULE-COMPLIANCE STATUS deprecated -- superceded by zoneServerMIBComplianceRev6 DESCRIPTION "The compliance statement for entities which implement the Zone Server." MODULE MANDATORY-GROUPS {zoneConfigurationGroup4, zoneStatisticsGroup, zoneNotificationControlGroup1, zoneNotificationGroup1} GROUP zoneLunStatsGroup DESCRIPTION "Only entities that support LUN zoning need to support this group." OBJECT zoneSetRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneSetActivateRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneAliasRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneMemberRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneCopyRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneCopyServerAddrType SYNTAX INTEGER { ipv4(1) } DESCRIPTION "Only IPv4 support is required." ::= { zoneServerMIBCompliances 6 } zoneServerMIBComplianceRev6 MODULE-COMPLIANCE STATUS deprecated -- superceded by zoneServerMIBComplianceRev7 DESCRIPTION "The compliance statement for entities which implement the Zone Server." MODULE MANDATORY-GROUPS {zoneConfigurationGroup5, zoneStatisticsGroup, zoneNotificationControlGroup1, zoneNotificationGroup1} GROUP zoneLunStatsGroup DESCRIPTION "Only entities that support LUN zoning need to support this group." OBJECT zoneSetRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneSetActivateRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneAliasRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneMemberRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneCopyRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneCopyServerAddrType SYNTAX INTEGER { ipv4(1) } DESCRIPTION "Only IPv4 support is required." ::= { zoneServerMIBCompliances 7 } zoneServerMIBComplianceRev7 MODULE-COMPLIANCE STATUS deprecated -- superceded by zoneServerMIBComplianceRev8 DESCRIPTION "The compliance statement for entities which implement the Zone Server." MODULE MANDATORY-GROUPS {zoneConfigurationGroup6, zoneStatisticsGroup, zoneNotificationControlGroup1, zoneNotificationGroup2, zoneNotificationControlGroup1Sup1} GROUP zoneLunStatsGroup DESCRIPTION "Only entities that support LUN zoning need to support this group." OBJECT zoneSetRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneSetActivateRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneAliasRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneMemberRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneCopyRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneCopyServerAddrType SYNTAX INTEGER { ipv4(1) } DESCRIPTION "Only IPv4 support is required." ::= { zoneServerMIBCompliances 8 } zoneServerMIBComplianceRev8 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement the Zone Server." MODULE MANDATORY-GROUPS {zoneConfigurationGroup7, zoneStatisticsGroup, zoneNotificationControlGroup1, zoneNotificationGroup2, zoneNotificationControlGroup1Sup1, zoneConfigGroupSup2} GROUP zoneLunStatsGroup DESCRIPTION "Only entities that support LUN zoning need to support this group." GROUP zoneConfigGroupSup1 DESCRIPTION "Only entities that need to associate more than 2048 zones per zoneset need to support this group." GROUP zoneNotificationControlGroup1Sup2 DESCRIPTION "Only entities that support more than 2048 zones per zoneset need to support this group." GROUP zoneNotificationGroup2Sup1 DESCRIPTION "Only entities that support more than 2048 zones per zoneset need to support this group." OBJECT zoneSetRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneSetActivateRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneAliasRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneMemberRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneCopyRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT zoneCopyServerAddrType SYNTAX INTEGER { ipv4(1) } DESCRIPTION "Only IPv4 support is required." ::= { zoneServerMIBCompliances 9 } -- Units of Conformance zoneConfigurationGroup OBJECT-GROUP OBJECTS {zoneSetPropagationMode, zoneDefaultZoneBehaviour, zoneSetNumber, zoneSetName, zoneSetZoneList, zoneSetLastChange, zoneSetRowStatus, zoneSetActivate, zoneSetActivateResult, zoneSetDeActivate, zoneSetActivateRowStatus, zoneNumber, zoneName, zoneMemberList, zoneAliasList, zoneLastChange, zoneRowStatus, zoneAliasNumber, zoneAliasName, zoneAliasMemberList, zoneAliasRowStatus, zoneMemberNumber, zoneMemberFormat, zoneMemberID, zoneMemberLunID, zoneMemberRowStatus, zoneEnforcedZoneSetNumber, zoneEnforcedZoneSetName, zoneEnforcedZoneSetZoneList, zoneEnforcedZoneSetActivateTime, zoneEnforcedZoneNumber, zoneEnforcedZoneName, zoneEnforcedZoneMemberList, zoneEnforcedZoneAliasList, zoneEnforcedZoneActivateTime, zoneEnforcedZoneAliasNumber, zoneEnforcedZoneAliasName, zoneEnforcedZoneAliasMemberList, zoneEnforcedZoneMemberNumber, zoneEnforcedZoneMemberFormat, zoneEnforcedZoneMemberID, zoneEnforcedZoneMemberLunID, zoneMergeFailRecoverSpinLock, zoneMergeFailRecoverInterface, zoneMergeFailRecoverVsan, zoneMergeFailRecoverOper, zoneMergeFailRecoverResult, zoneCopyActiveToFullOnVsan} STATUS deprecated DESCRIPTION "A collection of objects for displaying and configuring Zone Membership." ::= { zoneServerMIBGroups 1 } zoneStatisticsGroup OBJECT-GROUP OBJECTS {zoneTotalGS3Rejects, zoneTxMergeReqs, zoneRxMergeAccepts, zoneRxMergeReqs, zoneTxMergeAccepts, zoneTxChangeReqs, zoneRxChangeAccepts, zoneRxChangeReqs, zoneTxChangeAccepts, zoneRxGS3Reqs, zoneTxGS3Rejects} STATUS current DESCRIPTION "A collection of objects for displaying the Zone Server statistics information." ::= { zoneServerMIBGroups 2 } zoneNotificationControlGroup OBJECT-GROUP OBJECTS {zoneServiceReqRejNotifyEnable, zoneMergeFailureNotifyEnable, zoneMergeSuccessNotifyEnable, zoneDefZoneBehvrChngNotifyEnable, zoneServiceRejReasonCode, zoneServiceRejReasonCodeExp, zoneMergeFailureVSANNum, zoneMergeSuccessVSANNum} STATUS deprecated DESCRIPTION "A collection of notification control and notification information objects for monitoring Zone Server request rejection and zone merge failures." ::= { zoneServerMIBGroups 3 } zoneNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS {zoneServiceReqRejNotify, zoneMergeFailureNotify, zoneMergeSuccessNotify, zoneDefZoneBehaviourChngNotify} STATUS deprecated DESCRIPTION "A collection of notification(s) for monitoring Zone Server request rejection, zone merge failures and successes and default zoning behavioural changes." ::= { zoneServerMIBGroups 4 } zoneConfigurationGroup1 OBJECT-GROUP OBJECTS {zoneSetPropagationMode, zoneDefaultZoneBehaviour, zoneSetNumber, zoneSetName, zoneSetZoneList, zoneSetLastChange, zoneSetRowStatus, zoneSetActivate, zoneSetActivateResult, zoneSetDeActivate, zoneSetActivateRowStatus, zoneSetFailCause, zoneSetFailDomId, zoneNumber, zoneName, zoneMemberList, zoneAliasList, zoneLastChange, zoneRowStatus, zoneReadOnly, zoneAliasNumber, zoneAliasName, zoneAliasMemberList, zoneAliasRowStatus, zoneMemberNumber, zoneMemberFormat, zoneMemberID, zoneMemberLunID, zoneMemberRowStatus, zoneEnforcedZoneSetNumber, zoneEnforcedZoneSetName, zoneEnforcedZoneSetZoneList, zoneEnforcedZoneSetActivateTime, zoneEnforcedZoneNumber, zoneEnforcedZoneName, zoneEnforcedZoneMemberList, zoneEnforcedZoneAliasList, zoneEnforcedZoneActivateTime, zoneEnforcedZoneReadOnly, zoneEnforcedZoneAliasNumber, zoneEnforcedZoneAliasName, zoneEnforcedZoneAliasMemberList, zoneEnforcedZoneMemberNumber, zoneEnforcedZoneMemberFormat, zoneEnforcedZoneMemberID, zoneEnforcedZoneMemberLunID, zoneMergeFailRecoverSpinLock, zoneMergeFailRecoverInterface, zoneMergeFailRecoverVsan, zoneMergeFailRecoverOper, zoneMergeFailRecoverResult, zoneCopyActiveToFullOnVsan, zoneDbClearDb, zoneDbEnforcedEqualsLocal} STATUS deprecated -- replaced by zoneConfigurationGroup2 DESCRIPTION "A collection of objects for displaying and configuring Zone Membership and deleting the local zone server database." ::= { zoneServerMIBGroups 5 } zoneConfigurationGroup2 OBJECT-GROUP OBJECTS {zoneSetPropagationMode, zoneDefaultZoneBehaviour, zoneDefaultZoneReadOnly, zoneSetNumber, zoneSetName, zoneSetZoneList, zoneSetLastChange, zoneSetRowStatus, zoneSetActivate, zoneSetActivateResult, zoneSetDeActivate, zoneSetActivateRowStatus, zoneSetFailCause, zoneSetFailDomId, zoneNumber, zoneName, zoneMemberList, zoneAliasList, zoneLastChange, zoneRowStatus, zoneReadOnly, zoneAliasNumber, zoneAliasName, zoneAliasMemberList, zoneAliasRowStatus, zoneAliasLastChange, zoneMemberNumber, zoneMemberFormat, zoneMemberID, zoneMemberLunID, zoneMemberRowStatus, zoneEnforcedZoneSetNumber, zoneEnforcedZoneSetName, zoneEnforcedZoneSetZoneList, zoneEnforcedZoneSetActivateTime, zoneEnforcedZoneNumber, zoneEnforcedZoneName, zoneEnforcedZoneMemberList, zoneEnforcedZoneAliasList, zoneEnforcedZoneActivateTime, zoneEnforcedZoneReadOnly, zoneEnforcedZoneMemberNumber, zoneEnforcedZoneMemberFormat, zoneEnforcedZoneMemberID, zoneEnforcedZoneMemberLunID, zoneMergeFailRecoverSpinLock, zoneMergeFailRecoverInterface, zoneMergeFailRecoverVsan, zoneMergeFailRecoverOper, zoneMergeFailRecoverResult, zoneCopyActiveToFullOnVsan, zoneDbClearDb, zoneDbEnforcedEqualsLocal} STATUS deprecated -- replaced by zoneConfigurationGroup3 DESCRIPTION "A collection of objects for displaying and configuring Zone Membership and deleting the local zone server database." ::= { zoneServerMIBGroups 6 } zoneLunStatsGroup OBJECT-GROUP OBJECTS {zoneLunRxInqReqs, zoneLunRxRepLunReqs, zoneLunRxSenseReqs, zoneLunRxOtherCmds, zoneLunTxInqDataNoLus, zoneLunTxIllegalReqs, zoneRoZoneTxDataProts} STATUS current DESCRIPTION "A collection of objects for displaying the Zone Server LUN statistics information." ::= { zoneServerMIBGroups 7 } zoneConfigurationGroup3 OBJECT-GROUP OBJECTS {zoneSetPropagationMode, zoneDefaultZoneBehaviour, zoneDefaultZoneReadOnly, zoneSetNumber, zoneSetName, zoneSetZoneList, zoneSetLastChange, zoneSetRowStatus, zoneSetActivate, zoneSetActivateResult, zoneSetDeActivate, zoneSetActivateRowStatus, zoneSetFailCause, zoneSetFailDomId, zoneNumber, zoneName, zoneMemberList, zoneAliasList, zoneLastChange, zoneRowStatus, zoneReadOnly, zoneAliasNumber, zoneAliasName, zoneAliasMemberList, zoneAliasRowStatus, zoneAliasLastChange, zoneMemberNumber, zoneMemberFormat, zoneMemberID, zoneMemberLunID, zoneMemberRowStatus, zoneEnforcedZoneSetNumber, zoneEnforcedZoneSetName, zoneEnforcedZoneSetZoneList, zoneEnforcedZoneSetActivateTime, zoneEnforcedZoneNumber, zoneEnforcedZoneName, zoneEnforcedZoneMemberList, zoneEnforcedZoneAliasList, zoneEnforcedZoneActivateTime, zoneEnforcedZoneReadOnly, zoneEnforcedZoneMemberNumber, zoneEnforcedZoneMemberFormat, zoneEnforcedZoneMemberID, zoneEnforcedZoneMemberLunID, zoneMergeFailRecoverSpinLock, zoneMergeFailRecoverInterface, zoneMergeFailRecoverVsan, zoneMergeFailRecoverOper, zoneMergeFailRecoverResult, zoneCopyActiveToFullOnVsan, zoneDbClearDb, zoneDbEnforcedEqualsLocal, zoneCopyProto, zoneCopyDestFileType, zoneCopyServerAddrType, zoneCopyServerAddr, zoneCopyDestFileName, zoneCopyUserName, zoneCopyUserPassword, zoneCopyStartCopy, zoneCopyState, zoneCopyRowStatus} STATUS deprecated DESCRIPTION "A collection of objects for displaying and configuring Zone Membership and deleting the local zone server database." ::= { zoneServerMIBGroups 8 } zoneNotificationControlGroup1 OBJECT-GROUP OBJECTS {zoneServiceReqRejNotifyEnable, zoneMergeFailureNotifyEnable, zoneMergeSuccessNotifyEnable, zoneDefZoneBehvrChngNotifyEnable, zoneUnsuppMemInIntOpNotifyEnable, zoneServiceRejReasonCode, zoneServiceRejReasonCodeExp, zoneMergeFailureVSANNum, zoneMergeSuccessVSANNum, zoneVsanId} STATUS current DESCRIPTION "A collection of notification control and notification information objects for monitoring Zone Server request rejection and zone merge failures." ::= { zoneServerMIBGroups 9 } zoneNotificationGroup1 NOTIFICATION-GROUP NOTIFICATIONS {zoneServiceReqRejNotify, zoneMergeFailureNotify, zoneMergeSuccessNotify, zoneDefZoneBehaviourChngNotify, zoneUnsuppMemInIntOpModeNotify} STATUS deprecated -- superceded by zoneNotificationGroup2 DESCRIPTION "A collection of notification(s) for monitoring Zone Server request rejection, zone merge failures and successes and default zoning behavioural changes." ::= { zoneServerMIBGroups 10 } zoneConfigurationGroup4 OBJECT-GROUP OBJECTS {zoneSetPropagationMode, zoneDefaultZoneBehaviour, zoneDefaultZoneReadOnly, zoneSetNumber, zoneSetName, zoneSetZoneList, zoneSetLastChange, zoneSetRowStatus, zoneSetActivate, zoneSetActivateResult, zoneSetDeActivate, zoneSetActivateRowStatus, zoneSetFailCause, zoneSetFailDomId, zoneNumber, zoneName, zoneMemberList, zoneAliasList, zoneLastChange, zoneRowStatus, zoneReadOnly, zoneAliasNumber, zoneAliasName, zoneAliasMemberList, zoneAliasRowStatus, zoneAliasLastChange, zoneMemberNumber, zoneMemberFormat, zoneMemberID, zoneMemberLunID, zoneMemberRowStatus, zoneEnforcedZoneSetNumber, zoneEnforcedZoneSetName, zoneEnforcedZoneSetZoneList, zoneEnforcedZoneSetActivateTime, zoneEnforcedZoneNumber, zoneEnforcedZoneName, zoneEnforcedZoneMemberList, zoneEnforcedZoneAliasList, zoneEnforcedZoneActivateTime, zoneEnforcedZoneReadOnly, zoneEnforcedZoneMemberNumber, zoneEnforcedZoneMemberFormat, zoneEnforcedZoneMemberID, zoneEnforcedZoneMemberLunID, zoneMergeFailRecoverSpinLock, zoneMergeFailRecoverInterface, zoneMergeFailRecoverVsan, zoneMergeFailRecoverOper, zoneMergeFailRecoverResult, zoneCopyActiveToFullOnVsan, zoneDbClearDb, zoneDbEnforcedEqualsLocal, zoneCopyProto, zoneCopyDestFileType, zoneCopyServerAddrType, zoneCopyServerAddr, zoneCopyDestFileName, zoneCopyUserName, zoneCopyUserPassword, zoneCopyStartCopy, zoneCopyState, zoneCopyRowStatus, zoneZoneSetDistributeVsan, zoneZoneSetDistributeResult, zoneZoneSetDistributeFailReason} STATUS deprecated DESCRIPTION "A collection of objects for displaying and configuring Zone Membership and deleting the local zone server database." ::= { zoneServerMIBGroups 11 } zoneConfigurationGroup5 OBJECT-GROUP OBJECTS {zoneSetPropagationMode, zoneDefaultZoneBehaviour, zoneDefaultZoneReadOnly, zoneDefaultZoneQos, zoneDefaultZoneQosPriority, zoneDefaultZoneBroadcast, zoneSetNumber, zoneSetName, zoneSetZoneList, zoneSetLastChange, zoneSetRowStatus, zoneSetActivate, zoneSetActivateResult, zoneSetDeActivate, zoneSetActivateRowStatus, zoneSetFailCause, zoneSetFailDomId, zoneNumber, zoneName, zoneMemberList, zoneAliasList, zoneLastChange, zoneRowStatus, zoneReadOnly, zoneQos, zoneQosPriority, zoneBroadcast, zoneAliasNumber, zoneAliasName, zoneAliasMemberList, zoneAliasRowStatus, zoneAliasLastChange, zoneMemberNumber, zoneMemberFormat, zoneMemberID, zoneMemberLunID, zoneMemberRowStatus, zoneEnforcedZoneSetNumber, zoneEnforcedZoneSetName, zoneEnforcedZoneSetZoneList, zoneEnforcedZoneSetActivateTime, zoneEnforcedZoneNumber, zoneEnforcedZoneName, zoneEnforcedZoneMemberList, zoneEnforcedZoneAliasList, zoneEnforcedZoneActivateTime, zoneEnforcedZoneReadOnly, zoneEnforcedZoneQos, zoneEnforcedZoneQosPriority, zoneEnforcedZoneBroadcast, zoneEnforcedZoneMemberNumber, zoneEnforcedZoneMemberFormat, zoneEnforcedZoneMemberID, zoneEnforcedZoneMemberLunID, zoneMergeFailRecoverSpinLock, zoneMergeFailRecoverInterface, zoneMergeFailRecoverVsan, zoneMergeFailRecoverOper, zoneMergeFailRecoverResult, zoneCopyActiveToFullOnVsan, zoneDbClearDb, zoneDbEnforcedEqualsLocal, zoneCopyProto, zoneCopyDestFileType, zoneCopyServerAddrType, zoneCopyServerAddr, zoneCopyDestFileName, zoneCopyUserName, zoneCopyUserPassword, zoneCopyStartCopy, zoneCopyState, zoneCopyRowStatus, zoneZoneSetDistributeVsan, zoneZoneSetDistributeResult, zoneZoneSetDistributeFailReason} STATUS deprecated DESCRIPTION "A collection of objects for displaying and configuring Zone Membership and deleting the local zone server database." ::= { zoneServerMIBGroups 12 } zoneConfigurationGroup6 OBJECT-GROUP OBJECTS {zoneSetPropagationMode, zoneDefaultZoneBehaviour, zoneDefaultZoneReadOnly, zoneDefaultZoneQos, zoneDefaultZoneQosPriority, zoneDefaultZoneBroadcast, zoneSetNumber, zoneSetName, zoneSetZoneList, zoneSetLastChange, zoneSetRowStatus, zoneSetClone, zoneSetActivate, zoneSetActivateResult, zoneSetDeActivate, zoneSetActivateRowStatus, zoneSetFailCause, zoneSetFailDomId, zoneNumber, zoneName, zoneMemberList, zoneAliasList, zoneLastChange, zoneRowStatus, zoneReadOnly, zoneQos, zoneQosPriority, zoneBroadcast, zoneClone, zoneAliasNumber, zoneAliasName, zoneAliasMemberList, zoneAliasRowStatus, zoneAliasLastChange, zoneAliasClone, zoneMemberNumber, zoneMemberFormat, zoneMemberID, zoneMemberLunID, zoneMemberRowStatus, zoneEnforcedZoneSetNumber, zoneEnforcedZoneSetName, zoneEnforcedZoneSetZoneList, zoneEnforcedZoneSetActivateTime, zoneEnforcedZoneNumber, zoneEnforcedZoneName, zoneEnforcedZoneMemberList, zoneEnforcedZoneAliasList, zoneEnforcedZoneActivateTime, zoneEnforcedZoneReadOnly, zoneEnforcedZoneQos, zoneEnforcedZoneQosPriority, zoneEnforcedZoneBroadcast, zoneEnforcedZoneMemberNumber, zoneEnforcedZoneMemberFormat, zoneEnforcedZoneMemberID, zoneEnforcedZoneMemberLunID, zoneMergeFailRecoverSpinLock, zoneMergeFailRecoverInterface, zoneMergeFailRecoverVsan, zoneMergeFailRecoverOper, zoneMergeFailRecoverResult, zoneCopyActiveToFullOnVsan, zoneDbClearDb, zoneDbEnforcedEqualsLocal, zoneDbHardZoningEnabled, zoneCopyProto, zoneCopyDestFileType, zoneCopyServerAddrType, zoneCopyServerAddr, zoneCopyDestFileName, zoneCopyUserName, zoneCopyUserPassword, zoneCopyStartCopy, zoneCopyState, zoneCopyRowStatus, zoneZoneSetDistributeVsan, zoneZoneSetDistributeResult, zoneZoneSetDistributeFailReason} STATUS deprecated -- superceded by zoneConfigurationGroup7 DESCRIPTION "A collection of objects for displaying and configuring Zone Membership and deleting the local zone server database." ::= { zoneServerMIBGroups 13 } zoneNotificationGroup2 NOTIFICATION-GROUP NOTIFICATIONS {zoneServiceReqRejNotify, zoneMergeFailureNotify, zoneMergeSuccessNotify, zoneDefZoneBehaviourChngNotify, zoneUnsuppMemInIntOpModeNotify, zoneActivateNotify} STATUS current DESCRIPTION "A collection of notification(s) for monitoring Zone Server request rejection, zone merge failures and successes and default zoning behavioural changes." ::= { zoneServerMIBGroups 14 } zoneNotificationControlGroup1Sup1 OBJECT-GROUP OBJECTS { zoneSwitchWwn } STATUS current DESCRIPTION "A group that supplements zoneNotificationControlGroup1 with additional object(s)." ::= { zoneServerMIBGroups 15 } zoneConfigGroupSup1 OBJECT-GROUP OBJECTS { zoneSetZoneListBmap4k, zoneSetZoneListBmap6k, zoneSetZoneListBmap8k, zoneSetEnforcedZoneListBmap4k, zoneSetEnforcedZoneListBmap6k, zoneSetEnforcedZoneListBmap8k, zoneCompactFirst2k } STATUS current DESCRIPTION "A collection of objects to associate zones to zonesets and facilitate compaction of first 2k zones associated with zonesets." ::= { zoneServerMIBGroups 16 } zoneNotificationControlGroup1Sup2 OBJECT-GROUP OBJECTS { zoneCompactVsan, zoneMergeFailureObject, zoneMergeFailureReason } STATUS current DESCRIPTION "A group that supplements zoneNotificationControlGroup1 with additional notification information object(s)." ::= { zoneServerMIBGroups 17 } zoneNotificationGroup2Sup1 NOTIFICATION-GROUP NOTIFICATIONS { zoneCompactNotify } STATUS current DESCRIPTION "A group that supplements zoneNotificationGroup2 with additional notification(s)." ::= { zoneServerMIBGroups 18 } zoneConfigGroupSup2 OBJECT-GROUP OBJECTS { zoneCopyActToFullSpinLock, zoneCopyActToFullMode, zoneCopyActToFullVsan } STATUS current DESCRIPTION "A collection of objects to copy active zonesets to full zonesets on a VSAN." ::= { zoneServerMIBGroups 19 } zoneConfigurationGroup7 OBJECT-GROUP OBJECTS {zoneSetPropagationMode, zoneDefaultZoneBehaviour, zoneDefaultZoneReadOnly, zoneDefaultZoneQos, zoneDefaultZoneQosPriority, zoneDefaultZoneBroadcast, zoneSetNumber, zoneSetName, zoneSetZoneList, zoneSetLastChange, zoneSetRowStatus, zoneSetClone, zoneSetActivate, zoneSetActivateResult, zoneSetDeActivate, zoneSetActivateRowStatus, zoneSetFailCause, zoneSetFailDomId, zoneNumber, zoneName, zoneMemberList, zoneAliasList, zoneLastChange, zoneRowStatus, zoneReadOnly, zoneQos, zoneQosPriority, zoneBroadcast, zoneClone, zoneAliasNumber, zoneAliasName, zoneAliasMemberList, zoneAliasRowStatus, zoneAliasLastChange, zoneAliasClone, zoneMemberNumber, zoneMemberFormat, zoneMemberID, zoneMemberLunID, zoneMemberRowStatus, zoneEnforcedZoneSetNumber, zoneEnforcedZoneSetName, zoneEnforcedZoneSetZoneList, zoneEnforcedZoneSetActivateTime, zoneEnforcedZoneNumber, zoneEnforcedZoneName, zoneEnforcedZoneMemberList, zoneEnforcedZoneAliasList, zoneEnforcedZoneActivateTime, zoneEnforcedZoneReadOnly, zoneEnforcedZoneQos, zoneEnforcedZoneQosPriority, zoneEnforcedZoneBroadcast, zoneEnforcedZoneMemberNumber, zoneEnforcedZoneMemberFormat, zoneEnforcedZoneMemberID, zoneEnforcedZoneMemberLunID, zoneMergeFailRecoverSpinLock, zoneMergeFailRecoverInterface, zoneMergeFailRecoverVsan, zoneMergeFailRecoverOper, zoneMergeFailRecoverResult, zoneDbClearDb, zoneDbEnforcedEqualsLocal, zoneDbHardZoningEnabled, zoneCopyProto, zoneCopyDestFileType, zoneCopyServerAddrType, zoneCopyServerAddr, zoneCopyDestFileName, zoneCopyUserName, zoneCopyUserPassword, zoneCopyStartCopy, zoneCopyState, zoneCopyRowStatus, zoneZoneSetDistributeVsan, zoneZoneSetDistributeResult, zoneZoneSetDistributeFailReason} STATUS current DESCRIPTION "A collection of objects for displaying and configuring Zone Membership and deleting the local zone server database." ::= { zoneServerMIBGroups 20 } END