-- ***************************************************************** -- CISCO-WIRELESS-EXP-MIB.my: Cisco Wireless Radio Point to Point -- Experimental MIB. -- May 1999, Joseph L Raja -- Copyright (c) 1998-2005 by Cisco Systems, Inc. -- All rights reserved. -- ***************************************************************** CISCO-WIRELESS-EXP-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Unsigned32 FROM SNMPv2-SMI DateAndTime, DisplayString FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF ifIndex FROM IF-MIB entPhysicalIndex FROM ENTITY-MIB ciscoExperiment FROM CISCO-SMI; ciscoWirelessExpMIB MODULE-IDENTITY LAST-UPDATED "200512271003Z" ORGANIZATION "Cisco Systems Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: firestar-sw@cisco.com" DESCRIPTION "This is the MIB Module for the Cisco Wireless Radio Point to Point experimental components. Glossary The following terms are used in the MIB definitions below. Radio Card: The line card that provides the wireless communication features. Radio Link: The bi-directional wireless link that exists between two communicating radio cards. Radio PHY: Represents the transmission characteristics of the Radio Link. RF Unit: The Radio Frequency components and the associated antennas. Radio System: Radio card and RF unit(s). Cisco Wireless Radio Experimental MIB Organization The Cisco Wireless Radio Experimental MIB provides the following management groups : When the draft-ietf-entmib-v2-03.txt gets finalized the Radio Frequency Group will be moved into that MIB. When the CISCO-IMAGE-MIB.my gets updated to include the image capabilities, the Image Group will be migrated into that MIB. When the CISCO-LED-MIB.my becomes available and supports the functionality the LED group needs, the LED group will be migrated into that. o. Radio Frequency Resource Group This contains information about the Radio frequency transmission and reception resources available on the system. This group determines the portions of the radio spectrum at which the radio subsystem can operate. This group in conjunction with the radio PHY group determine the acutal spectrum that gets used for communications. o. Image Group This provides facilities to manage radio line card's firmware image file URL's in router's image repository. It also provides access to the image details. o. LED Group This group provides information about LEDs available on the line card. o. Duplexor Group This group provides information about the Duplexors installed in the RF resources." REVISION "200512271003Z" DESCRIPTION "Imported Unsigned32 from SNMPv2-SMI." REVISION "9905132010Z" DESCRIPTION "The initial version of this MIB module." ::= { ciscoExperiment 52 } -- The Cisco Wireless Radio MIB Tree cwrRadioExpMibObjects OBJECT IDENTIFIER ::= { ciscoWirelessExpMIB 1 } cwrRadioFreqEntityGroup OBJECT IDENTIFIER ::= { cwrRadioExpMibObjects 1 } cwrRadioImageGroup OBJECT IDENTIFIER ::= { cwrRadioExpMibObjects 2 } cwrRadioLedGroup OBJECT IDENTIFIER ::= { cwrRadioExpMibObjects 3 } cwrRadioDuplexorGroup OBJECT IDENTIFIER ::= { cwrRadioExpMibObjects 4 } -- The Radio Frequency Entity Group. -- The RF Table. This table contains information about the Radio frequency -- Entities available for use on the system. cwrRfEntityTable OBJECT-TYPE SYNTAX SEQUENCE OF CwrRfEntityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information about the radio frequency resources available for use on the system." ::= { cwrRadioFreqEntityGroup 1 } cwrRfEntityEntry OBJECT-TYPE SYNTAX CwrRfEntityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This represents one entry in the cwrRfEntityTable. This table is largely a read only table which provides details on the radio frequency resources available on the system. Physically each RF resource may be realized by one antenna and its associated control hardware. But a single antenna and its associated hardware may act as more than 1 RF resource. A Duplexor is a mechanical device, that acts as a band pass filter when installed in an RF resource. Normally a RF resource is capable of operating over a wide frequency range. To operate at restricted frequencies, the user has to own that part of the frequency spectrum. Since the user may not own parts of the frequency spectrum over which the RF resource may operate, a Duplexor is installed in the RF resource. This restricts the RF resource to operate in the passband defined by the Duplexor. In this table the Duplexor's are identified by an index into the cwrDuplexorTable. It is indexed by the ifIndex and cwrRfEntityIndex." INDEX { ifIndex, cwrRfEntityIndex } ::= { cwrRfEntityTable 1 } CwrRfEntityEntry ::= SEQUENCE { cwrRfEntityIndex Integer32, cwrRfSwRevision Unsigned32, cwrRfAssemblyPartNumberClass Unsigned32, cwrRfAssemblyPartNumberBase Unsigned32, cwrRfAssemblyPartNumberVersion Unsigned32, cwrRfBoardPartNumberClass Unsigned32, cwrRfBoardPartNumberBase Unsigned32, cwrRfBoardPartNumberVersion Unsigned32, cwrRfBoardRevision DisplayString, cwrRfSerialNumber DisplayString, cwrRfManfDate DateAndTime, cwrRfVendorId Integer32, cwrRfDuplexorIndex Integer32 } cwrRfEntityIndex OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents the index of this entry in the cwrRfEntityTable." ::= { cwrRfEntityEntry 1 } cwrRfSwRevision OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the software revision number of controlling the RF subsystem." ::= { cwrRfEntityEntry 2 } cwrRfAssemblyPartNumberClass OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the assembly part number class of the RF subsystem." ::= { cwrRfEntityEntry 3 } cwrRfAssemblyPartNumberBase OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the assembly part number base of the RF subsystem." ::= { cwrRfEntityEntry 4 } cwrRfAssemblyPartNumberVersion OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the assembly part number version of the RF subsystem." ::= { cwrRfEntityEntry 5 } cwrRfBoardPartNumberClass OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the board part number class of the RF subsystem." ::= { cwrRfEntityEntry 6 } cwrRfBoardPartNumberBase OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the board part number base of the RF subsystem." ::= { cwrRfEntityEntry 7 } cwrRfBoardPartNumberVersion OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the board part number version of the RF subsystem." ::= { cwrRfEntityEntry 8 } cwrRfBoardRevision OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the board revision of the RF subsystem." ::= { cwrRfEntityEntry 9 } cwrRfSerialNumber OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the serial number of the RF subsystem." ::= { cwrRfEntityEntry 10 } cwrRfManfDate OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the manufacturing date of the RF subsystem." ::= { cwrRfEntityEntry 11 } cwrRfVendorId OBJECT-TYPE SYNTAX Integer32 (1..256) MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the Radio frequency device vendor ID." ::= { cwrRfEntityEntry 12 } cwrRfDuplexorIndex OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the index into cwrDuplexorTable. This index identifies the Duplexor associated with this RF resource." ::= { cwrRfEntityEntry 13 } -- The Intermediate Frequency Entity table. This table contains -- information about the Intermediate Frequency subsystem on the radio -- card. cwrIntFreqEntityTable OBJECT-TYPE SYNTAX SEQUENCE OF CwrIntFreqEntityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information about the intermediate frequency subsystem on the radio card." ::= { cwrRadioFreqEntityGroup 2 } cwrIntFreqEntityEntry OBJECT-TYPE SYNTAX CwrIntFreqEntityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This represents one entry in the cwrIntFreqEntityTable. This table is largely a read only table which provides details on the intermediate frequency subsystem available on the radio card. It is indexed by the ifIndex." INDEX { ifIndex } ::= { cwrIntFreqEntityTable 1 } CwrIntFreqEntityEntry ::= SEQUENCE { cwrIfAssemblyPartNumberClass Unsigned32, cwrIfAssemblyPartNumberBase Unsigned32, cwrIfAssemblyPartNumberVersion Unsigned32, cwrIfBoardPartNumberClass Unsigned32, cwrIfBoardPartNumberBase Unsigned32, cwrIfBoardPartNumberVersion Unsigned32, cwrIfBoardRevision DisplayString, cwrIfSerialNumber DisplayString, cwrIfManfDate DateAndTime, cwrIfVendorId Integer32, cwrIfSwRevision Unsigned32 } cwrIfAssemblyPartNumberClass OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the assembly part number class of the IF subsystem." ::= { cwrIntFreqEntityEntry 1 } cwrIfAssemblyPartNumberBase OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the assembly part number base of the IF subsystem." ::= { cwrIntFreqEntityEntry 2 } cwrIfAssemblyPartNumberVersion OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the assembly part number version of the IF subsystem." ::= { cwrIntFreqEntityEntry 3 } cwrIfBoardPartNumberClass OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the board part number class of the IF subsystem." ::= { cwrIntFreqEntityEntry 4 } cwrIfBoardPartNumberBase OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the board part number base of the IF subsystem." ::= { cwrIntFreqEntityEntry 5 } cwrIfBoardPartNumberVersion OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the board part number version of the IF subsystem." ::= { cwrIntFreqEntityEntry 6 } cwrIfBoardRevision OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the board revision of the IF subsystem." ::= { cwrIntFreqEntityEntry 7 } cwrIfSerialNumber OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the serial number of the IF subsystem." ::= { cwrIntFreqEntityEntry 8 } cwrIfManfDate OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the manufacturing date of the IF subsystem." ::= { cwrIntFreqEntityEntry 9 } cwrIfVendorId OBJECT-TYPE SYNTAX Integer32 (1..256) MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the IF vendor ID." ::= { cwrIntFreqEntityEntry 10 } cwrIfSwRevision OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the IF software revision." ::= { cwrIntFreqEntityEntry 11 } -- The Image Group. -- The Firmware Image Table. This table provides facilities to manage -- the firmware images that the router will use for configuring the -- radio line cards. cwrImageTable OBJECT-TYPE SYNTAX SEQUENCE OF CwrImageEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides facilities to manage the firmware images that the router will use to configure the radio line cards. When images need to be downloaded, the software will search this list starting from the first, for an image whose capabilities match the configuration specified in the cwrRadioBaseTable and the cwrRadioPhyTable and download that image to the appropriate hardware component. Insertion into the table at arbitrary points is not supported. Any new image URL added to this table will be inserted at index 1 only. Also note that an image gets downloaded to the hardware only when when a radio link is administratively enabled." ::= { cwrRadioImageGroup 1 } cwrImageEntry OBJECT-TYPE SYNTAX CwrImageEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This represents one entry in the cwrImageTable." INDEX { cwrImageIndex } ::= { cwrImageTable 1 } CwrImageEntry ::= SEQUENCE { cwrImageIndex Integer32, cwrImageNameUrl DisplayString, cwrImageState INTEGER, cwrImageSize Unsigned32, cwrImageChipClass Unsigned32, cwrImageChipType Unsigned32, cwrImageCapability1 Unsigned32, cwrImageCapability2 Unsigned32, cwrImageVersion Unsigned32, cwrImageTag DisplayString, cwrImageOp INTEGER } cwrImageIndex OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This represents the one entry in this table. It also represents the search order. When images need to be downloaded to the hardware, the images are searched in the order of this index for an image that matches the hardware capabilities and uses it." ::= { cwrImageEntry 1 } cwrImageNameUrl OBJECT-TYPE SYNTAX DisplayString (SIZE (1..255)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is the name of the image in the Universal Resource Locator (URL) format. This URL will be used to access the image when needed." ::= { cwrImageEntry 2 } cwrImageState OBJECT-TYPE SYNTAX INTEGER { imageInvalid(1), imageValid(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This represents the state of the image. image_invalid(1): If the image could not be accessed for any reason. image_valid(2) : Image accessible and available for use." ::= { cwrImageEntry 3 } cwrImageSize OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This represents the size of the image in bytes." ::= { cwrImageEntry 4 } cwrImageChipClass OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This represents the class of chips onto which this image may be loaded." ::= { cwrImageEntry 5 } cwrImageChipType OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This represents the download method to use." ::= { cwrImageEntry 6 } cwrImageCapability1 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This represents a bitmask. The bit mask identifies the capabilities of this image. See also cwrImageCapability2." ::= { cwrImageEntry 7 } cwrImageCapability2 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This represents a bitmask. The bit mask identifies the capabilities of this image in addition to cwrImageCapability1." ::= { cwrImageEntry 8 } cwrImageVersion OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This represents the version number of this image." ::= { cwrImageEntry 9 } cwrImageTag OBJECT-TYPE SYNTAX DisplayString (SIZE (1..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object is the tag string associated with the image. Normally used to trace the source code used to generate this image." ::= { cwrImageEntry 10 } cwrImageOp OBJECT-TYPE SYNTAX INTEGER { nop(0), add(1), delete(2), move(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the operation to be performed on the identified image. nop(0) - This value will be returned when this object is read. add(1) - Will add the image URL, as the first entry in the image table. delete(2) - Will delete the specified ULR from the image table. move(3) - Will make the image specified by the URL the first entry in the imageTable." ::= { cwrImageEntry 11 } -- The LED Group. cwrLedTable OBJECT-TYPE SYNTAX SEQUENCE OF CwrLedEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entity (Light emitting diode) LED information. For each LED on the entity, an entry will exist in this table, describing the location and current status of that LED." ::= { cwrRadioLedGroup 1 } cwrLedEntry OBJECT-TYPE SYNTAX CwrLedEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table, containing the LED information about the entity. The entPhysicalIndex identifies the entity on which the Led's are present." INDEX { entPhysicalIndex, cwrLedIndex } ::= { cwrLedTable 1 } CwrLedEntry ::= SEQUENCE { cwrLedIndex INTEGER, cwrLedName DisplayString, cwrLedVerticalPosition Integer32, cwrLedHorizontalPosition Integer32, cwrLedMode INTEGER, cwrLedCurrentColor INTEGER } cwrLedIndex OBJECT-TYPE SYNTAX INTEGER (1..16) MAX-ACCESS not-accessible STATUS current DESCRIPTION "For a given entPhysicalIndex, this index value uniquely identifies an entry in the cwrLedTable." ::= { cwrLedEntry 1 } cwrLedName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The label of the LED on the physical entity or a textual description to identify the usage of the LED." ::= { cwrLedEntry 2 } cwrLedVerticalPosition OBJECT-TYPE SYNTAX Integer32 (1..16) MAX-ACCESS read-only STATUS current DESCRIPTION "The position of the LED in the entity. It is counted from top to bottom." ::= { cwrLedEntry 3 } cwrLedHorizontalPosition OBJECT-TYPE SYNTAX Integer32 (1..16) MAX-ACCESS read-only STATUS current DESCRIPTION "The position of the LED in the entity. It is counted from from left to right." ::= { cwrLedEntry 4 } cwrLedMode OBJECT-TYPE SYNTAX INTEGER { automatic(1), latched(2), forceOff(3), forceSolidGreen(4), forceSolidYellow(5), forceBlinkGreen(6), forceBlinkYellow(7), forceBlinkBoth(8) } MAX-ACCESS read-write STATUS current DESCRIPTION "This objects specifies the desired mode of LED updates. automatic(1) and latched(2) are settings used by the software to determine how the LED should be updated. The others are for diagnostic purposes. The LED will be turned on or off as specified by the other (3-8) settings. The modes mean the following: automatic(1): The system updates the LED according to the default settings for that entity. latched(2): Once the LED is turned on, user has to turn it off. This applies only to alarm LEDs. forceOff(3): Force the LED off. forceSolidGreen(4): Force the LED to be solid green in on state. forceSolidYellow(5):Force the LED to be solid Yellow in on state forceBlinkGreen(6): Force the LED to blink in Green. forceBlinkYellow(7):Force the LED to blink in Yellow. forceBlinkBoth(8): Force the LED to blink Yellow and Green alternatively." ::= { cwrLedEntry 5 } cwrLedCurrentColor OBJECT-TYPE SYNTAX INTEGER { green(1), yellow(2), blinkGreen(3), blinkYellow(4), blinkGreenYellow(5), off(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the current color of the LED." ::= { cwrLedEntry 6 } -- The Duplexor Group. -- The Duplexor Table. This table contains information about the -- Duplexor Entities available for use on the system. -- A Duplexor is a mechanical device, that acts as a bandpass filter -- when installed in an RF resource. cwrDuplexorTable OBJECT-TYPE SYNTAX SEQUENCE OF CwrDuplexorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information about the Duplexors available for use on the system." ::= { cwrRadioDuplexorGroup 1 } cwrDuplexorEntry OBJECT-TYPE SYNTAX CwrDuplexorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This represents one entry in the cwrDuplexorTable. This table provides details on the Duplexors available on the system. It is indexed by the ifIndex and cwrDuplexorIndex." INDEX { ifIndex, cwrDuplexorIndex } ::= { cwrDuplexorTable 1 } CwrDuplexorEntry ::= SEQUENCE { cwrDuplexorIndex Integer32, cwrDuplexorCiscoPartNumber DisplayString, cwrDuplexorLoPassbandRange DisplayString, cwrDuplexorHiPassbandRange DisplayString, cwrDuplexorReceivePassband INTEGER, cwrDuplexorCLEICode DisplayString, cwrDuplexorVendorName DisplayString, cwrDuplexorSerialNumber DisplayString } cwrDuplexorIndex OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents the index of this entry in the cwrDuplexorTable." ::= { cwrDuplexorEntry 1 } cwrDuplexorCiscoPartNumber OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the Cisco part number for this Duplexor." ::= { cwrDuplexorEntry 2 } cwrDuplexorLoPassbandRange OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the low frequency range that this Duplexor will pass through without any attenuation. All low frequencies outside this range will be attenuated to a level such that an RF resource that uses this Duplexor will be unable to transmit or receive those frequencies." ::= { cwrDuplexorEntry 3 } cwrDuplexorHiPassbandRange OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the high frequency range that this Duplexor will pass through without any attenuation. All high frequencies outside this range will be attenuated to a level such that an RF resource that uses this Duplexor will be unable to transmit or receive those frequencies." ::= { cwrDuplexorEntry 4 } cwrDuplexorReceivePassband OBJECT-TYPE SYNTAX INTEGER { loPassband(1), hiPassband(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates which of the two passbands are being used to receive transmissions. The RF Resource can receive on either of the duplexor passbands. loPassband(1) - The RF Resource is receiving on a frequency within the range identified by cwrDuplexorLoPassbandRange. hiPassband(2) - The RF Resource is receiving on a frequency within the range identified by cwrDuplexorHiPassbandRange." ::= { cwrDuplexorEntry 5 } cwrDuplexorCLEICode OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The CLEI code for this Duplexor." ::= { cwrDuplexorEntry 6 } cwrDuplexorVendorName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The Vendor Name for this Duplexor." ::= { cwrDuplexorEntry 7 } cwrDuplexorSerialNumber OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The Serial number of this Duplexor." ::= { cwrDuplexorEntry 8 } -- ============================================================================ -- Compliance Statements cwrRadioExpConformance OBJECT IDENTIFIER ::= { ciscoWirelessExpMIB 2 } cwrRadioExpCompliances OBJECT IDENTIFIER ::= { cwrRadioExpConformance 1 } cwrRadioExpGroups OBJECT IDENTIFIER ::= { cwrRadioExpConformance 2 } cwrRadioExpCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for Point to Point wireless interface devices compliant to Cisco Systems Inc. specification." MODULE -- this module MANDATORY-GROUPS { cwrComplianceRadioRFGroup, cwrComplianceRadioImageGroup, cwrComplianceRadioLEDGroup, cwrComplianceRadioDuplexorGroup } ::= { cwrRadioExpCompliances 1 } -- Required Radio frequency resource Group. cwrComplianceRadioRFGroup OBJECT-GROUP OBJECTS { cwrRfSwRevision, cwrRfAssemblyPartNumberClass, cwrRfAssemblyPartNumberBase, cwrRfAssemblyPartNumberVersion, cwrRfBoardPartNumberClass, cwrRfBoardPartNumberBase, cwrRfBoardPartNumberVersion, cwrRfBoardRevision, cwrRfSerialNumber, cwrRfManfDate, cwrRfVendorId, cwrRfDuplexorIndex, cwrIfAssemblyPartNumberClass, cwrIfAssemblyPartNumberBase, cwrIfAssemblyPartNumberVersion, cwrIfBoardPartNumberClass, cwrIfBoardPartNumberBase, cwrIfBoardPartNumberVersion, cwrIfBoardRevision, cwrIfSerialNumber, cwrIfManfDate, cwrIfVendorId, cwrIfSwRevision } STATUS current DESCRIPTION "Group of objects implemented in the point to point wireless system for managing the Radio Frequency resources on the link." ::= { cwrRadioExpGroups 1 } -- Required Image Group. cwrComplianceRadioImageGroup OBJECT-GROUP OBJECTS { cwrImageNameUrl, cwrImageState, cwrImageSize, cwrImageChipType, cwrImageChipClass, cwrImageCapability1, cwrImageCapability2, cwrImageVersion, cwrImageTag, cwrImageOp } STATUS current DESCRIPTION "Group of objects implemented in the point to point wireless system for managing images related to the point-to-point wireless firmware." ::= { cwrRadioExpGroups 2 } -- Required LED group. cwrComplianceRadioLEDGroup OBJECT-GROUP OBJECTS { cwrLedName, cwrLedVerticalPosition, cwrLedHorizontalPosition, cwrLedMode, cwrLedCurrentColor } STATUS current DESCRIPTION "Group of objects implemented in the point to point wireless card to provide information about the LEDs on the card." ::= { cwrRadioExpGroups 3 } -- Required Duplexor group. cwrComplianceRadioDuplexorGroup OBJECT-GROUP OBJECTS { cwrDuplexorCiscoPartNumber, cwrDuplexorLoPassbandRange, cwrDuplexorHiPassbandRange, cwrDuplexorReceivePassband, cwrDuplexorCLEICode, cwrDuplexorVendorName, cwrDuplexorSerialNumber } STATUS current DESCRIPTION "Group of objects implemented in the point to point wireless card to provide information about the duplexor's in the system." ::= { cwrRadioExpGroups 4 } END