-- ***************************************************************** -- ciscoWanSvcMIB - SVC MIB -- -- April 2000, Wendy Cheng -- -- Copyright (c) 1999-2003 by Cisco Systems, Inc. -- All rights reserved. -- ***************************************************************** CISCO-WAN-SVC-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Counter32, Integer32 FROM SNMPv2-SMI DisplayString, RowStatus, TimeStamp, TruthValue, TEXTUAL-CONVENTION FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF ifIndex, InterfaceIndex FROM IF-MIB PnniNodeId, PnniPortId FROM PNNI-MIB AtmAddress, NetPrefix FROM ATM-FORUM-TC-MIB CiscoWanNsapAtmAddress FROM CISCO-WAN-ATM-CONN-MIB stratacom FROM CISCOWAN-SMI; ciscoWANSvcMIB MODULE-IDENTITY LAST-UPDATED "200303100000Z" ORGANIZATION "Cisco System, Inc" CONTACT-INFO "Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95143 USA Tel: +1 800 553-NETS E-mail: cs-wanatm@cisco.com" DESCRIPTION "The MIB modules describe an ATM network service on a BPX-SES or a MGX ATM switch. This MIB module provides configuring, provisioning, as well as status gathering for ATM services. Abbreviation used: ABR -- Available Bit Rate AINI -- ATM Inter-Network Interface ATM -- Asynchronous Transfer Mode BGN -- Begin BW -- Bandwidth CBR -- Constant Bit Rate ENNI -- Enhanced Network to Network Interface Note: The 'ENNI' term used here indicating 'enhanced' or 'friendly' NNI for linking two networks of CISCO AutoRoute or PNNI switches. The XPVCs and XPVPs are provisioned across them. Functionality includes changing segment OAM cell handling so that these cells flow over 'end-to-end OAM segment' loops for the provisioned length of the XPVC or XPVP, i.e. the 'segment' comprises the two or three segments between the user ports. Also implemented at ENNIs is an LMI functionality that enables auto-discovery of the ENNIs. ER -- Error Recovery GAT -- Generic Application Transport IE -- Information Element IISP -- Interim Inter-Switch Signaling Protocol ILMI -- Interim Local Management Interface MD -- Management Data PNNI -- Private Network-Network Interface RS -- Resynchronization REJ -- Rejection SD -- Sequence Data SDP -- Sequence Data with Poll SPVC -- Soft Permanent Virtual Circuit SSCOP -- Service Specific Connection Oriented Protocol SVC -- Switched Virtual Circuit UBR -- Unspecified Bit Rate UD -- Unit Data UNI -- User-Network Interface USTAT -- Unsolicited STAT VBR -- Variable Bit Rate" REVISION "200303100000Z" DESCRIPTION "a) Modified to have characters/line to be less than 72 and add range for Integer32. b) Modified to use cwspConfigGrp3 in ciscoWANSvcMIBCompliance3. " REVISION "200209160000Z" DESCRIPTION "a) Added 'cwspSpvcAddress' to cwspConfigTable." REVISION "200203010000Z" DESCRIPTION "a) Added 'cwspRoutingPriority' object in cwspConfigTable. b) The DEFVAL clause for 'cwspUniVersion' and 'cwspNniVersion' is changed to 'unsupported(7)' from 'uni31'. The DESCRIPTION is modified for these objects." REVISION "200107190000Z" DESCRIPTION "The change is to back out previous revision. The requirement was changed." REVISION "200107060000Z" DESCRIPTION "The change is to use 'unsupoerted(7)' as default for both 'cwspUniVersion' and 'cwspNniVersion'. DESCRIPTION modified for both variables as well." REVISION "200106060000Z" DESCRIPTION "The change is to add 'self(9)' enumeration to 'cwspUniVersion'. This value is used to indicate a voice port." REVISION "200105100000Z" DESCRIPTION "The changes are as follows: (1) Add one mib variable 'cwspConnTraceLastNode'. (2) Add 'unsupported(7)'to 'cwspNniVersion' variable. (3) Add additional comments in DESCRIPTION of 'cwspNniVersion' and 'cwspUniVersion' variables. (4) Corrected spelling error." REVISION "200010200000Z" DESCRIPTION "The changes are as follows: (1) Description for 'ENNI' is added. (2) cwspNniVersion -- enumeration enni(4) and aini(5) are added. (3) cwspOperNniSigVersion -- enumeration aini(5) is added." REVISION "200009010000Z" DESCRIPTION "The changes are as follows: (1) The default value of cwspMinSvccVci is changed to 35. (2) The lower range of cwspMaxSvccVci changed to 35." REVISION "200008030000Z" DESCRIPTION "Importing symbol stratacom from CISCOWAN-SMI instead from BASIS-MIB." REVISION "200006150000Z" DESCRIPTION "The changes are as follows. (1) The lower bound and upper bound of the following MIB objects has been changed from 0 to 1 and from 100 to 200 respectively. (i) cwspUtilFactorCbr (ii) cwspUtilFactorRtVbr (iii) cwspUtilFactorNrtVbr (iv) cwspUtilFactorAbr (v) cwspUtilFactorUbr (2) The lower bound of cwspMinSvccVci object has been changed from 32 to 0." REVISION "200004010000Z" DESCRIPTION "This is the initial version of this MIB module." ::= { stratacom 140 } ciscoWANSvcMIBObjects OBJECT IDENTIFIER ::= { ciscoWANSvcMIB 1 } ciscoWANSvcInfo OBJECT IDENTIFIER ::= { ciscoWANSvcMIBObjects 1 } ciscoWANSvcPort OBJECT IDENTIFIER ::= { ciscoWANSvcMIBObjects 2 } ciscoWANPnniRouting OBJECT IDENTIFIER ::= { ciscoWANSvcMIBObjects 3 } ciscoWANSpvc OBJECT IDENTIFIER ::= { ciscoWANSvcMIBObjects 4 } cwspConfig OBJECT IDENTIFIER ::= { ciscoWANSvcPort 1 } cwspCacConfig OBJECT IDENTIFIER ::= { ciscoWANSvcPort 2 } cwspSigConfig OBJECT IDENTIFIER ::= { ciscoWANSvcPort 3 } cwspSscopConfig OBJECT IDENTIFIER ::= { ciscoWANSvcPort 4 } cwspCallStats OBJECT IDENTIFIER ::= { ciscoWANSvcPort 5 } cwspSigStats OBJECT IDENTIFIER ::= { ciscoWANSvcPort 6 } cwspSscopStats OBJECT IDENTIFIER ::= { ciscoWANSvcPort 7 } cwspCall OBJECT IDENTIFIER ::= { ciscoWANSvcPort 8 } cwspAbrCall OBJECT IDENTIFIER ::= { ciscoWANSvcPort 9 } cwspPrefix OBJECT IDENTIFIER ::= { ciscoWANSvcPort 10 } cwspAddress OBJECT IDENTIFIER ::= { ciscoWANSvcPort 11 } cwspRegAddress OBJECT IDENTIFIER ::= { ciscoWANSvcPort 12 } cwspLoad OBJECT IDENTIFIER ::= { ciscoWANSvcPort 13 } cwspConnTrace OBJECT IDENTIFIER ::= { ciscoWANSvcPort 14 } cwspOperation OBJECT IDENTIFIER ::= { ciscoWANSvcPort 15 } -- TEXTUAL CONVENTIONS USED IN THIS MIB CwspSpvcState ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Defines possible failures at an endpoint. The following are implemented: genSpvcErr(1) -- General SPVC error, sRecvSetupConfmMismatch(12) -- Connection ATM Conformance type -- mismatch with master at slave endpoint. sRecvSetupServMismatch(13) -- Connection Service type mismatch with -- master at slave endpoint. sRecvSetupTrafParmMismatch(14), -- Traffic parameters mismatch with master -- at slave endpoint. masterSpvcAutoDelete(15) -- Controller auto deleting provisioned -- master SPVC. and slaveSpvcAutoDelete(16) -- Controller auto deleting provisioned -- slave SPVC." SYNTAX INTEGER { genSpvcErr(1), mPvcDelFail(2), sPvcDelFail(3), mRelPendHalfTmout(4), mInstlPvcFail(5), sInstlPvcFail(6), mRecmtPvcFail(7), sRecmtPvcFail(8), mCmtHalfFail(9), sCmtHalfFail(10), mInstlXconnFail(11), sRecvSetupConfmMismatch(12), sRecvSetupServMismatch(13), sRecvSetupTrafParmMismatch(14), masterSpvcAutoDelete(15), slaveSpvcAutoDelete(16) } CwspControllerState ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Defines possible state for the pnni controller." SYNTAX INTEGER { ready(1), unavilable(2) } -- the system group -- svc information group cwsSwRevision OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "PNNI network controller software revision number." ::= { ciscoWANSvcInfo 1 } cwsControllerStatus OBJECT-TYPE SYNTAX CwspControllerState MAX-ACCESS read-only STATUS current DESCRIPTION "The administrative status for the pnni active controller." ::= { ciscoWANSvcInfo 6 } cwspPnniStndbyControllerStatus OBJECT-TYPE SYNTAX CwspControllerState MAX-ACCESS read-only STATUS current DESCRIPTION "The administrative status for the standby controller." ::= { ciscoWANSvcInfo 7 } cwspPnniControllerStatus OBJECT-TYPE SYNTAX INTEGER { active(1), stndby(2), unavailable(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The administrative status of the pnni controller. Note: this object is only used in the trap varbind, snmp get operation is meaningless." ::= { ciscoWANSvcInfo 8 } cwspPnniControllerPhySlot OBJECT-TYPE SYNTAX Integer32(1..16) MAX-ACCESS read-only STATUS current DESCRIPTION "The pnni controller physical location for MGX or BPX-SES. Note: this object is only used in the trap varbind, snmp get operation is meaningless." ::= { ciscoWANSvcInfo 9 } -- the port SSCOP configuration table cwspSscopTable OBJECT-TYPE SYNTAX SEQUENCE OF CwspSscopEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies SSCOP (Layer 2) configuration parameters." ::= { cwspSscopConfig 1 } cwspSscopEntry OBJECT-TYPE SYNTAX CwspSscopEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the SSCOP configuration table. Each entry indexed by the ifIndex of a port." INDEX { ifIndex } ::= { cwspSscopTable 1 } CwspSscopEntry ::= SEQUENCE { cwspSscopTmrCC Integer32, cwspSscopTmrKeepAlive Integer32, cwspSscopTmrNoResp Integer32, cwspSscopTmrPoll Integer32, cwspSscopTmtIdle Integer32, cwspSscopMaxCC Integer32, cwspSscopMaxPD Integer32, cwspSscopMaxSTAT Integer32 } cwspSscopTmrCC OBJECT-TYPE SYNTAX Integer32 (0..2147483647) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object contains the value for Connection control timer." DEFVAL { 1 } ::= { cwspSscopEntry 1 } cwspSscopTmrKeepAlive OBJECT-TYPE SYNTAX Integer32 (0..2147483647) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object contains the value for keep alive timer " DEFVAL { 5 } ::= { cwspSscopEntry 2 } cwspSscopTmrNoResp OBJECT-TYPE SYNTAX Integer32 (0..2147483647) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object contains the value for no response timer." DEFVAL { 30 } ::= { cwspSscopEntry 3 } cwspSscopTmrPoll OBJECT-TYPE SYNTAX Integer32 (0..2147483647) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object contains the value for poll timer." DEFVAL { 1 } ::= { cwspSscopEntry 4 } cwspSscopTmtIdle OBJECT-TYPE SYNTAX Integer32 (0..2147483647) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object contains the value for idle timer." DEFVAL { 10 } ::= { cwspSscopEntry 5 } cwspSscopMaxCC OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "This object contains the upper limit for the number of transmissions of a BGN, END, ER or RS PDU." DEFVAL { 10 } ::= { cwspSscopEntry 6 } cwspSscopMaxPD OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "This object contains an upper limit for a counter which counts the number of SD PDUs transmitted between transmissions of POLL PDUs or the number of SD PDUs transmitted before the transmission of the first POLL PDU after POLL timer became active." DEFVAL { 10 } ::= { cwspSscopEntry 7 } cwspSscopMaxSTAT OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "This object contains an upper limit for the number of list elements placed in a STAT PDU." DEFVAL { 67 } ::= { cwspSscopEntry 8 } -- the port SSCOP statistics cwspSscopStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF CwspSscopStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains SSCOP (Layer 2) statistics counters." ::= { cwspSscopStats 1 } cwspSscopStatsEntry OBJECT-TYPE SYNTAX CwspSscopStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry contains SSCOP (Layer 2) statistics." INDEX { ifIndex } ::= { cwspSscopStatsTable 1 } CwspSscopStatsEntry ::= SEQUENCE { cwspSscopCounterReset INTEGER, cwspSscopIgnoredPduRcv Counter32, cwspSscopBgnRcv Counter32, cwspSscopBgakRcv Counter32, cwspSscopEndRcv Counter32, cwspSscopEndakRcv Counter32, cwspSscopRsRcv Counter32, cwspSscopRsakRcv Counter32, cwspSscopBgrejRcv Counter32, cwspSscopSdRcv Counter32, cwspSscopSdpRcv Counter32, cwspSscopPollRcv Counter32, cwspSscopStatRcv Counter32, cwspSscopUstatRcv Counter32, cwspSscopUdRcv Counter32, cwspSscopMdRcv Counter32, cwspSscopErakRcv Counter32, cwspSscopBgnXmt Counter32, cwspSscopBgakXmt Counter32, cwspSscopEndXmt Counter32, cwspSscopEndakXmt Counter32, cwspSscopRsXmt Counter32, cwspSscopRsakXmt Counter32, cwspSscopBgrejXmt Counter32, cwspSscopSdXmt Counter32, cwspSscopSdpXmt Counter32, cwspSscopPollXmt Counter32, cwspSscopStatXmt Counter32, cwspSscopUstatXmt Counter32, cwspSscopUdXmt Counter32, cwspSscopMdXmt Counter32, cwspSscopErakXmt Counter32 } cwspSscopCounterReset OBJECT-TYPE SYNTAX INTEGER { noop(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether the SSCOP statistics collected for this interface needs to be reset." DEFVAL { noop } ::= { cwspSscopStatsEntry 1 } cwspSscopIgnoredPduRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP PDUs that are received but ignored due to incorrect size, invalid PDU, unknown PDU type." ::= { cwspSscopStatsEntry 2 } cwspSscopBgnRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP BGN PDUs received at this interface." ::= { cwspSscopStatsEntry 3 } cwspSscopBgakRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP BGN ACK PDUs received at this interface." ::= { cwspSscopStatsEntry 4 } cwspSscopEndRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP END PDUs received at this interface." ::= { cwspSscopStatsEntry 5 } cwspSscopEndakRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP END ACK PDUs received at this interface." ::= { cwspSscopStatsEntry 6 } cwspSscopRsRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP RS(Resync) PDUs received at this interface." ::= { cwspSscopStatsEntry 7 } cwspSscopRsakRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP RS(Resync) ACK PDUs received at this interface." ::= { cwspSscopStatsEntry 8 } cwspSscopBgrejRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP BGN REJ PDUs received at this interface." ::= { cwspSscopStatsEntry 9 } cwspSscopSdRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP SD (Sequenced Data) PDUs received at this interface." ::= { cwspSscopStatsEntry 10 } cwspSscopSdpRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP SDP (Sequenced Data with Poll) PDUs received at this interface." ::= { cwspSscopStatsEntry 11 } cwspSscopPollRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP POLL PDUs received at this interface." ::= { cwspSscopStatsEntry 12 } cwspSscopStatRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP STAT PDUs received at this interface." ::= { cwspSscopStatsEntry 13 } cwspSscopUstatRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP USTAT (Unsolicited STAT) PDUs received at this interface." ::= { cwspSscopStatsEntry 14 } cwspSscopUdRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP UD (Unit data) PDUs received at this interface." ::= { cwspSscopStatsEntry 15 } cwspSscopMdRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP MD (Management data) PDUs received at this interface." ::= { cwspSscopStatsEntry 16 } cwspSscopErakRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP ER ACK (error recovery ack) PDUs received at this interface." ::= { cwspSscopStatsEntry 17 } cwspSscopBgnXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP BGN PDUs transmitted over this interface." ::= { cwspSscopStatsEntry 18 } cwspSscopBgakXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP BGN ACK PDUs transmitted on this interface." ::= { cwspSscopStatsEntry 19 } cwspSscopEndXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP END PDUs transmitted on this interface." ::= { cwspSscopStatsEntry 20 } cwspSscopEndakXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP END ACK PDUs transmitted on this interface." ::= { cwspSscopStatsEntry 21 } cwspSscopRsXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP RS (Resync) PDUs transmitted over this interface." ::= { cwspSscopStatsEntry 22 } cwspSscopRsakXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP RS (Resync) ACK PDUs transmitted over this interface." ::= { cwspSscopStatsEntry 23 } cwspSscopBgrejXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP BGN REJ PDUs transmitted over this interface." ::= { cwspSscopStatsEntry 24 } cwspSscopSdXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP SD transmitted over this interface." ::= { cwspSscopStatsEntry 25 } cwspSscopSdpXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP SDP PDUs transmitted over this interface." ::= { cwspSscopStatsEntry 26 } cwspSscopPollXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP POLL PDUs transmitted over this interface." ::= { cwspSscopStatsEntry 27 } cwspSscopStatXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP STAT PDUs transmitted over this interface." ::= { cwspSscopStatsEntry 28 } cwspSscopUstatXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP USTAT PDUs transmitted over this interface." ::= { cwspSscopStatsEntry 29 } cwspSscopUdXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP UD PDUs transmitted over this interface." ::= { cwspSscopStatsEntry 30 } cwspSscopMdXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP MD PDUs transmitted over this interface." ::= { cwspSscopStatsEntry 31 } cwspSscopErakXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object stores the number of SSCOP ER(error recovery) ACK PDUs transmitted over this interface." ::= { cwspSscopStatsEntry 32 } -- the port signaling configuration table cwspSigConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF CwspSigConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies signaling configuration parameters." ::= { cwspSigConfig 1 } cwspSigConfigEntry OBJECT-TYPE SYNTAX CwspSigConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the signaling configuration table. Each entry indexed by the ifIndex of a port." INDEX { ifIndex } ::= { cwspSigConfigTable 1 } CwspSigConfigEntry ::= SEQUENCE { cwspSigCfgT301 Integer32, cwspSigCfgT303 Integer32, cwspSigCfgT308 Integer32, cwspSigCfgT310 Integer32, cwspSigCfgT316 Integer32, cwspSigCfgT317 Integer32, cwspSigCfgT322 Integer32, cwspSigCfgT397 Integer32, cwspSigCfgT398 Integer32, cwspSigCfgT399 Integer32 } cwspSigCfgT301 OBJECT-TYPE SYNTAX Integer32 (150..240) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Timer started when ALERT message received at Call Received State. Normally, timer is stopped when CONNECT message is received. Clear call at first expiry." DEFVAL { 180 } ::= { cwspSigConfigEntry 1 } cwspSigCfgT303 OBJECT-TYPE SYNTAX Integer32 (4..8) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Timer started when SETUP message sent at Call Present State. Normally, timer is stopped when ALERT, CONNECT, RELEASE COMPLETE or CALL PROCEEDING message is received. Resend SETUP message and restart the timer at first expiry; Clear network connection and enter NULL state at second expiry." DEFVAL { 4 } ::= { cwspSigConfigEntry 2 } cwspSigCfgT308 OBJECT-TYPE SYNTAX Integer32 (20..45) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Timer started when RELEASE message sent at Release Indication State. Normally, timer is stopped when RELEASE COMPLETE or RELEASE message is received. Resend RELEASE and restart the timer at first expiry; Release call reference and enter NULL state at second expiry." DEFVAL { 30 } ::= { cwspSigConfigEntry 3 } cwspSigCfgT310 OBJECT-TYPE SYNTAX Integer32(10..120) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Timer started when CALL PROCEEDING message received at Incoming Call Proceeding State. Normally, timer is stopped when ALERT, CONNECT or RELEASE message is received. Clear call at first expiry. Range from 10 to 20 seconds for UNI 3.0/3.1 with default of 10; 30 to 120 seconds for UNI 4.0 with default of 30, default number can be 10 or 30, 10 is used." DEFVAL { 10 } ::= { cwspSigConfigEntry 4 } cwspSigCfgT316 OBJECT-TYPE SYNTAX Integer32 (90..300) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Timer started when RESTART message sent Restart Request State. Normally, timer is stopped when RESTART ACK message is received. RESTART may be sent multiple times in both first or second expiry." DEFVAL { 90 } ::= { cwspSigConfigEntry 5 } cwspSigCfgT317 OBJECT-TYPE SYNTAX Integer32 (60..300) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Timer started when RESTART message received at Restart State. Normally, timer is stopped when Internal clearing of call references happen. Maintenance notification at first expiry. The value of this timer should be less than T316." DEFVAL { 60 } ::= { cwspSigConfigEntry 6 } cwspSigCfgT322 OBJECT-TYPE SYNTAX Integer32 (4..20) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Timer started when STATUS ENQUIRY message sent at any call state. Normally, timer is stopped when STATUS RELEASE or RELEASE COMPLETE message is received. STATUS ENQUIREY message may be resent several times in both first or second expiry." DEFVAL { 4 } ::= { cwspSigConfigEntry 7 } cwspSigCfgT397 OBJECT-TYPE SYNTAX Integer32 (180..240) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Timer started when ALERTING or PARTY ALERTING message received in point-to-multipoint call. Normally timer is stopped when ADD PARTY ACK message is received. Clear party at first expiry." DEFVAL { 180 } ::= { cwspSigConfigEntry 8 } cwspSigCfgT398 OBJECT-TYPE SYNTAX Integer32 (4..20) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Timer is started when DROP PARTY message sent at Drop Party Initiated State. Normally, timer is stopped when DROP PARTY ACK or RELEASE message is received. Send DROP PARTY ACK or RELEASE at first expiry." DEFVAL { 4 } ::= { cwspSigConfigEntry 9 } cwspSigCfgT399 OBJECT-TYPE SYNTAX Integer32(14..124) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Timer is started when ADD PARTY message sent at Add Party Initiated State. Normally, timer is stopped when ADD PARTY ACK, ADD PARTY REJ or RELEASE message is received. Clear the party and enter NULL Party State at first expiry. Range from 14 to 28 seconds for UNI 3.0/3.1 with default of 14; 34 to 124 seconds for UNI 4.0 with default of 34, default can be 14 or 34, 14 is used." DEFVAL { 14 } ::= { cwspSigConfigEntry 10 } -- the port signaling statistics cwspSigStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF CwspSigStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains signaling statistics counters" ::= { cwspSigStats 1 } cwspSigStatsEntry OBJECT-TYPE SYNTAX CwspSigStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry contains signaling statistics." INDEX { ifIndex } ::= { cwspSigStatsTable 1 } CwspSigStatsEntry ::= SEQUENCE { cwspSigCounterReset INTEGER, cwspCallProcRcv Counter32, cwspConnectRcv Counter32, cwspConnectAckRcv Counter32, cwspSetupRcv Counter32, cwspReleaseRcv Counter32, cwspReleaseComplRcv Counter32, cwspRestartRcv Counter32, cwspRestartAckRcv Counter32, cwspStatusRcv Counter32, cwspStatusEnqRcv Counter32, cwspNotifyRcv Counter32, cwspAlertRcv Counter32, cwspProgressRcv Counter32, cwspAddPtyRcv Counter32, cwspAddPtyAckRcv Counter32, cwspAddPtyRejRcv Counter32, cwspDropPtyRcv Counter32, cwspIncorrectMsgRcv Counter32, cwspTimerExpiries Counter32, cwspLastCause Counter32, cwspLastDiagnostic Integer32, cwspCallProcXmt Counter32, cwspConnectXmt Counter32, cwspConnectAckXmt Counter32, cwspSetupXmt Counter32, cwspReleaseXmt Counter32, cwspReleaseComplXmt Counter32, cwspRestartXmt Counter32, cwspRestartAckXmt Counter32, cwspStatusXmt Counter32, cwspStatusEnqXmt Counter32, cwspNotifyXmt Counter32, cwspAlertXmt Counter32, cwspProgressXmt Counter32, cwspAddPtyXmt Counter32, cwspAddPtyAckXmt Counter32, cwspAddPtyRejXmt Counter32, cwspDropPtyXmt Counter32, cwspSscopStatus INTEGER } cwspSigCounterReset OBJECT-TYPE SYNTAX INTEGER { noop(1), -- none of following reset(2) -- resetting } MAX-ACCESS read-write STATUS current DESCRIPTION "Writing a 2 to this object resets the all Sig counters." DEFVAL { noop } ::= { cwspSigStatsEntry 1 } cwspCallProcRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of CALL PROCEEDING messages received on this interface." ::= { cwspSigStatsEntry 2 } cwspConnectRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of CONNECT messages received on this interface." ::= { cwspSigStatsEntry 3 } cwspConnectAckRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of CONNECT ACK messages received on this interface." ::= { cwspSigStatsEntry 4 } cwspSetupRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of SETUP messages received on this interface." ::= { cwspSigStatsEntry 5 } cwspReleaseRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of RELEASE messages received on this interface." ::= { cwspSigStatsEntry 6 } cwspReleaseComplRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of RELEASE COMPLETE messages received on this interface." ::= { cwspSigStatsEntry 7 } cwspRestartRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of RESTART messages received on this interface." ::= { cwspSigStatsEntry 8 } cwspRestartAckRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of RESTART ACK messages received on this interface." ::= { cwspSigStatsEntry 9 } cwspStatusRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of STATUS messages received on this interface." ::= { cwspSigStatsEntry 10 } cwspStatusEnqRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of STATUS ENQUIRY messages received on this interface." ::= { cwspSigStatsEntry 11 } cwspNotifyRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of NOTIFY messages received on this interface." ::= { cwspSigStatsEntry 12 } cwspAlertRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of ALERT messages received on this interface." ::= { cwspSigStatsEntry 13 } cwspProgressRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of PROGRESS messages received on this interface." ::= { cwspSigStatsEntry 14 } cwspAddPtyRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of ADD PARTY messages received on this interface." ::= { cwspSigStatsEntry 15 } cwspAddPtyAckRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of ADD PARTY ACK messages received on this interface." ::= { cwspSigStatsEntry 16 } cwspAddPtyRejRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of ADD PARTY REJECT messages received on this interface." ::= { cwspSigStatsEntry 17 } cwspDropPtyRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of DROP PARTY messages received on this interface." ::= { cwspSigStatsEntry 18 } cwspIncorrectMsgRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of Incorrect messages received on this interface." ::= { cwspSigStatsEntry 20 } cwspTimerExpiries OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of timeouts occurred on this interface." ::= { cwspSigStatsEntry 21 } cwspLastCause OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "to indicate the last cause of release or cranckback." ::= { cwspSigStatsEntry 22 } cwspLastDiagnostic OBJECT-TYPE SYNTAX Integer32(-2147483648..214743647) MAX-ACCESS read-only STATUS current DESCRIPTION "to indicate the last diagnostic of release or cranckback." ::= { cwspSigStatsEntry 23 } cwspCallProcXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of CALL PROCEEDING messages transmitted from this interface." ::= { cwspSigStatsEntry 24 } cwspConnectXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of CONNECT messages transmitted from this interface." ::= { cwspSigStatsEntry 25 } cwspConnectAckXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of CONNECT ACK messages transmitted from this interface." ::= { cwspSigStatsEntry 26 } cwspSetupXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of SETUP messages transmitted from this interface." ::= { cwspSigStatsEntry 27 } cwspReleaseXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of RELEASE messages transmitted from this interface." ::= { cwspSigStatsEntry 28 } cwspReleaseComplXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of RELEASE COMPLETE messages transmitted from this interface." ::= { cwspSigStatsEntry 29 } cwspRestartXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of RESTART messages transmitted from this interface." ::= { cwspSigStatsEntry 30 } cwspRestartAckXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of RESTART ACK messages transmitted from this interface." ::= { cwspSigStatsEntry 31 } cwspStatusXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of STATUS messages transmitted from this interface." ::= { cwspSigStatsEntry 32 } cwspStatusEnqXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of STATUS ENQUIRY messages transmitted from this interface." ::= { cwspSigStatsEntry 33 } cwspNotifyXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of NOTIFY messages transmitted from this interface." ::= { cwspSigStatsEntry 34 } cwspAlertXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of ALERT messages transmitted from this interface." ::= { cwspSigStatsEntry 35 } cwspProgressXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of PROGRESS messages transmitted from this interface." ::= { cwspSigStatsEntry 36 } cwspAddPtyXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of ADD PARTY messages transmitted from this interface." ::= { cwspSigStatsEntry 37 } cwspAddPtyAckXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of ADD PARTY ACK messages transmitted from this interface." ::= { cwspSigStatsEntry 38 } cwspAddPtyRejXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of ADD PARTY REJECT messages transmitted from this interface." ::= { cwspSigStatsEntry 39 } cwspDropPtyXmt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of DROP PARTY messages transmitted from this interface." ::= { cwspSigStatsEntry 40 } cwspSscopStatus OBJECT-TYPE SYNTAX INTEGER { up(1), -- sscop link is established down(2) -- sscop link is tailed } MAX-ACCESS read-only STATUS current DESCRIPTION "Sscop link status on an NNI interface, object is meaningful along with ciscoWANSscopLinkChange trap." ::= { cwspSigStatsEntry 42 } -- the interface configuration table cwspConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF CwspConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Interface configuration table collects attributes that affect the operation of the controller interface. There is a single row for each interface that the managed system is expected to be added or managed." ::= { cwspConfig 1 } cwspConfigEntry OBJECT-TYPE SYNTAX CwspConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " An entry in the interface configuration table containing information about an interface" INDEX { ifIndex } ::= { cwspConfigTable 1 } CwspConfigEntry ::= SEQUENCE { cwspAdminStatus INTEGER, cwspOperStatus INTEGER, cwspSvcBlocked TruthValue, cwspSpvcBlocked TruthValue, cwspIlmiAddrRegEnable TruthValue, cwspIlmiAutoConfEnable TruthValue, cwspIlmiServRegEnable TruthValue, cwspPhyIdentifier DisplayString, cwspSignallingVpi Integer32, cwspSignallingVci Integer32, cwspRoutingVpi Integer32, cwspRoutingVci Integer32, cwspMaxVpiBits Integer32, cwspMaxVciBits Integer32, cwspUniVersion INTEGER, cwspNniVersion INTEGER, cwspUniType INTEGER, cwspSide INTEGER, cwspMaxP2pCalls Integer32, cwspMaxP2mpRoots Integer32, cwspMaxP2mpLeafs Integer32, cwspMinSvccVpi Integer32, cwspMaxSvccVpi Integer32, cwspMinSvccVci Integer32, cwspMaxSvccVci Integer32, cwspMinSvpcVpi Integer32, cwspMaxSvpcVpi Integer32, cwspEnhancedIisp TruthValue, cwspConfigTableRowStatus RowStatus, cwspAddrPlanSupported INTEGER, cwspIlmiSecureLink TruthValue, cwspIlmiAttachmentPoint TruthValue, cwspIlmiLocalAttrStd TruthValue, cwspIlmiUCSMEnable TruthValue, cwspRoutingPriority Integer32, cwspSpvcAddress CiscoWanNsapAtmAddress } cwspAdminStatus OBJECT-TYPE SYNTAX INTEGER { inService(1), outService(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The administrative status of the interface. inService (1) means that the interface is operational while outService (2) indicates that the interface is put out of service by the administrator." DEFVAL { outService } ::= { cwspConfigEntry 1 } cwspOperStatus OBJECT-TYPE SYNTAX INTEGER { ok(1), failed(2), other(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The operational state of the interface. This status is derived from the physical state of the interface. failed (2) indicates that the interface has failed. ok (1) indicates that the interface is in operational status, while other (3) denotes that the interface is in an unknown state." ::= { cwspConfigEntry 2 } cwspSvcBlocked OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether Switches virtual connections are allowed through this interface." DEFVAL { false } ::= { cwspConfigEntry 3 } cwspSpvcBlocked OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether soft permanent virtual connections are allowed through this interface." DEFVAL { false } ::= { cwspConfigEntry 4 } cwspIlmiAddrRegEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether ILMI address registration is enabled or disabled." DEFVAL { true } ::= { cwspConfigEntry 5 } cwspIlmiAutoConfEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether auto-configuration of the interface is turned on or off. If auto-configuration is enabled, then the interface comes up using the ILMI auto-configuration." DEFVAL { true } ::= { cwspConfigEntry 6 } cwspIlmiServRegEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether service registry is enabled or disabled on the interface." DEFVAL { true } ::= { cwspConfigEntry 7 } cwspPhyIdentifier OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the physical identification of the interface. Mandatory when the port is provisioned for the first time through SNMP." ::= { cwspConfigEntry 8 } cwspSignallingVpi OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-create STATUS current DESCRIPTION "Denotes the Signaling VPI used on the interface." DEFVAL { 0 } ::= { cwspConfigEntry 9 } cwspSignallingVci OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the signaling VCI used on the interface, acceptable value is 32-65535, and 5 being the default." DEFVAL { 5 } ::= { cwspConfigEntry 10 } cwspRoutingVpi OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the VPI used for PNNI lowest level RCC." DEFVAL { 0 } ::= { cwspConfigEntry 11 } cwspRoutingVci OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the VCI used for the PNNI lowest level RCC, acceptable value is 32-65535, and 18 being the default." DEFVAL { 18 } ::= { cwspConfigEntry 12 } cwspMaxVpiBits OBJECT-TYPE SYNTAX Integer32 (0..12) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of active VPI bits on this ATM Interface. For virtual interfaces (i.e. Virtual Path Connections used by PNNI), this value has no meaning and is set to zero." ::= { cwspConfigEntry 13 } cwspMaxVciBits OBJECT-TYPE SYNTAX Integer32 (0..16) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of active VCI bits on this ATM Interface." ::= { cwspConfigEntry 14 } cwspUniVersion OBJECT-TYPE SYNTAX INTEGER { uni20(1), uni30(2), uni31(3), uni40(4), ituDss2(5), frf4(6), unsupported(7), ip(8), self(9) } MAX-ACCESS read-create STATUS current DESCRIPTION "An indication of the latest version of the ATM Forum UNI Signaling Specification that is supported on this ATM Interface. If this value is not present, a version of the UNI earlier than 3.1 is supported. The value of 'self(9)' indicates this entry is a voice port. If the peer IME's value of this object is the same as, or later than the local IME's value, then the version corresponding to the local IME's value should be attempted. Otherwise, if the peer IME's value of this object is earlier, and supported locally, then the local IME should attempt the version corresponding to the peer IME's value. Otherwise, compatibility of the two IMEs cannot be assumed." DEFVAL { unsupported } ::= { cwspConfigEntry 15 } cwspNniVersion OBJECT-TYPE SYNTAX INTEGER { iisp30(1), iisp31(2), pnni10(3), enni(4), aini(5), unsupported(7) } MAX-ACCESS read-create STATUS current DESCRIPTION "An indication of the latest version of the ATM Forum PNNI Signaling Specification that is supported on this ATM Interface. Note that the PNNI routing version is not determined through ILMI. If the peer IME's value of this object is the same as, or later than the local IME's value, then the version corresponding to the local IME's value should be attempted. Otherwise, if the peer IME's value of this object is earlier, and supported locally, then the local IME should attempt the version corresponding to the peer IME's value. Otherwise, compatibility of the two IMEs cannot be assumed." DEFVAL { unsupported } ::= { cwspConfigEntry 16 } cwspUniType OBJECT-TYPE SYNTAX INTEGER { public(1), private(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of the ATM device, either public or private." DEFVAL { private } ::= { cwspConfigEntry 17 } cwspSide OBJECT-TYPE SYNTAX INTEGER { user(1), network(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object determines the type of the ATM device. This object is used in automatic ATM Interface-Type determination procedure such that a correct operational ATM Interface-type can be determined. An ATM End System shall take the value of user(1), and an ATM network node shall take the value of node(2)." DEFVAL { network } ::= { cwspConfigEntry 18 } cwspMaxP2pCalls OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the maximum number of point to point calls (including VCs and VPs allowed on the interface." DEFVAL { 10000 } ::= { cwspConfigEntry 19 } cwspMaxP2mpRoots OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the maximum number of root VCs (for point-to-multipoint) allowed on the interface." DEFVAL { 1000 } ::= { cwspConfigEntry 20 } cwspMaxP2mpLeafs OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the maximum number of leaf VCs (for point-to-multipoint) allowed on the interface." DEFVAL { 4095 } ::= { cwspConfigEntry 21 } cwspMinSvccVpi OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the minimum SVCC VPI configured on the interface." DEFVAL { 0 } ::= { cwspConfigEntry 22 } cwspMaxSvccVpi OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the maximum SVCC VPI configured on the interface." DEFVAL { 4095 } ::= { cwspConfigEntry 23 } cwspMinSvccVci OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the minimum SVCC VCI configured on the interface." DEFVAL { 35 } ::= { cwspConfigEntry 24 } cwspMaxSvccVci OBJECT-TYPE SYNTAX Integer32 (35..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the maximum SVCC VCI configured on the interface." DEFVAL { 65535 } ::= { cwspConfigEntry 25 } cwspMinSvpcVpi OBJECT-TYPE SYNTAX Integer32 (1..4095) MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the minimum SVPC VPI configured on the interface." DEFVAL { 1 } ::= { cwspConfigEntry 26 } cwspMaxSvpcVpi OBJECT-TYPE SYNTAX Integer32 (1..4095) MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the maximum SVPC VPI configured on the interface." DEFVAL { 4095 } ::= { cwspConfigEntry 27 } cwspEnhancedIisp OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the enhanced features for IISP are enabled or disabled." DEFVAL { false } ::= { cwspConfigEntry 28 } cwspConfigTableRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Used to create and delete the Interface. However, only createAndGo, destroy, active and notInService are supported. NMS should only use createAndGo to create a row and destroy to delete a row. The managed device will either return active or notInService for a row status." ::= { cwspConfigEntry 29 } cwspAddrPlanSupported OBJECT-TYPE SYNTAX INTEGER { both(1), aesa(2), e164(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The ATM address plan supported on an interface. This can only be modified if interface is public UNI. For all other interfaces, the value is aesa." DEFVAL { aesa } ::= { cwspConfigEntry 30 } cwspIlmiSecureLink OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether ILMI Secure Link Protocol is enabled or disabled. When secure link protocol is enabled, loss in ILMI connectivity is treated as loss of attachment point which results in all SVCs/SVPs being released on the interface." DEFVAL { true } ::= { cwspConfigEntry 31 } cwspIlmiAttachmentPoint OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether detection of loss of attachment procedures are enabled on this interface. When set to true, then standard ILMI procedures are employed to detect loss of attachment point. If set to false, then ILMI protocol on the interface does not detect the loss of attachment." DEFVAL { true } ::= { cwspConfigEntry 32 } cwspIlmiLocalAttrStd OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether on modification of local attributes, procedures as recommended by ILMI 4.0 specification are followed or cisco proprietery procedures are followed. When set to true, the standard ILMI procedures are followed." DEFVAL { true } ::= { cwspConfigEntry 33 } cwspIlmiUCSMEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether ILMI user connection status monitoring is enabled or disabled." DEFVAL { true } ::= { cwspConfigEntry 34 } cwspRoutingPriority OBJECT-TYPE SYNTAX Integer32(1..15) MAX-ACCESS read-create STATUS current DESCRIPTION "This object is the routing priority to be assigned to connections which enter the network from this ingress interface, but does not carry the routing priority signaling in the SETUP message. SETUP message. A default routing priority of 8 is used if this object is not configured. A routing priority 1 is the highest priority for a user connection. A connection tagged with a routing priority of 1 is derouted ahead of connections tagged with other priority values." DEFVAL { 8 } ::= { cwspConfigEntry 35 } cwspSpvcAddress OBJECT-TYPE SYNTAX CiscoWanNsapAtmAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the internal NSAP assigned to a port by the switch. a) The format is that of 13-byte node prefix and 7-byte port number. b) When the switch's node prefix is modified, the node prefix part of this variable is also changed accordingly. Note: the switch's node prefix cannot be changed if there are connections on the switch. c) The port number can be physical port identifier or the ifIndex of this port." ::= { cwspConfigEntry 36 } -- the port call statistics table cwspCallStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF CwspCallStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This Table contains objects showing the Statistics for SVC/SPVC calls on a given interface." ::= { cwspCallStats 1 } cwspCallStatsEntry OBJECT-TYPE SYNTAX CwspCallStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry contains SVC/SPVC call statistics" INDEX { ifIndex } ::= { cwspCallStatsTable 1 } CwspCallStatsEntry ::= SEQUENCE { cwspCountReset INTEGER, cwspInCallAttempts Counter32, cwspInCallEstabs Counter32, cwspInCallFailures Counter32, cwspInFilterFailures Counter32, cwspInRouteFailures Counter32, cwspInResrcFailures Counter32, cwspInTimerFailures Counter32, cwspInCrankbacks Counter32, cwspOutCallAttempts Counter32, cwspOutCallEstabs Counter32, cwspOutCallFailures Counter32, cwspOutFilterFailures Counter32, cwspOutRouteFailures Counter32, cwspOutResrcFailures Counter32, cwspOutTimerFailures Counter32, cwspOutCrankbacks Counter32 } cwspCountReset OBJECT-TYPE SYNTAX INTEGER { noop(1), -- none of following reset(2) -- resetting } MAX-ACCESS read-write STATUS current DESCRIPTION "Writing a 2 to this object resets all counters." DEFVAL { noop } ::= { cwspCallStatsEntry 1 } cwspInCallAttempts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the number of incoming Signaling messages (Setup and Add Party) received by the switching node on this interface for Call establishment." ::= { cwspCallStatsEntry 2 } cwspInCallEstabs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the number of incoming Signaling Messages (Connect and Add Party Ack) received by the switching node on this interface which marks that a call has been successfully established." ::= { cwspCallStatsEntry 3 } cwspInCallFailures OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the total number of incoming Point-to-Point (p2p) and Point-to-MultiPoint(p2mp) SVC/SPVC call attempts failed on this interface." ::= { cwspCallStatsEntry 4 } cwspInFilterFailures OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the number of incoming Point-to-Point(p2p) and Point-to-MultiPoint(p2mp) SVC/SPVC call attempts which failed due to address filtering on this interface." ::= { cwspCallStatsEntry 5 } cwspInRouteFailures OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the number of incoming Point-to-Point(p2p) and Point-to-MulitPoint(p2mp) SVC/SPVC call attempts on this interface which failed because there was no route to the destination available." ::= { cwspCallStatsEntry 6 } cwspInResrcFailures OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the number of incoming Point-to-Point(p2p) and Point-to-MulitPoint(p2mp) SVC/SPVC call attempts on this interface which failed because there were not enough resources as requested in the parameters of the call." ::= { cwspCallStatsEntry 7 } cwspInTimerFailures OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the number of signaling timers timed out for incoming Point-to-Point(p2p) and Point-to-MultiPoint(p2mp) SVC/SPVC calls on this interface." ::= { cwspCallStatsEntry 8 } cwspInCrankbacks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the number of Crankback IEs received on this interface for incoming Point-to-Point(p2p) and Point-to-MultiPoint (p2mp) SVC/SPVC call attempts." ::= { cwspCallStatsEntry 9 } cwspOutCallAttempts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the number of outgoing Signaling messages (Setup and Add Party) on this interface for Call establishment." ::= { cwspCallStatsEntry 10 } cwspOutCallEstabs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the number of outgoing Signaling messages (Connect and Add Party Ack) which mark the call being established on this interface" ::= { cwspCallStatsEntry 11 } cwspOutCallFailures OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the total number of outgoing Signaling messages for Point-to-Point and Point-to-MultiPoint call establishment on this interface which failed." ::= { cwspCallStatsEntry 12 } cwspOutFilterFailures OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the number of outgoing Signaling messages for call establishment on this interface which failed the address filtering." ::= { cwspCallStatsEntry 13 } cwspOutRouteFailures OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the number of outgoing Signaling messages for call establishment on this interface which failed because the route was not available." ::= { cwspCallStatsEntry 14 } cwspOutResrcFailures OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the number of outgoing Signaling messages for call establishment on this interface which failed because the resource requested was not available." ::= { cwspCallStatsEntry 15 } cwspOutTimerFailures OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the number of Signaling timers timed-out on this interface for outgoing signaling messages." ::= { cwspCallStatsEntry 16 } cwspOutCrankbacks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the number of Crankback IEs being sent on this interface for outgoing signaling Release messages. This is generated on the node which generates the Crankback IEs." ::= { cwspCallStatsEntry 17 } -- the port prefix table cwspPrefixTable OBJECT-TYPE SYNTAX SEQUENCE OF CwspPrefixEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table specifying the network prefix(es) used for ILMI address registration." ::= { cwspPrefix 1 } cwspPrefixEntry OBJECT-TYPE SYNTAX CwspPrefixEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a single network prefix contained in the prefix table." INDEX { ifIndex, cwspNetPrefix } ::= { cwspPrefixTable 1 } CwspPrefixEntry ::= SEQUENCE { cwspNetPrefix NetPrefix, cwspPrefixRowStatus RowStatus } cwspNetPrefix OBJECT-TYPE SYNTAX NetPrefix MAX-ACCESS not-accessible STATUS current DESCRIPTION "The network prefix specified for use in ILMI address registration." ::= { cwspPrefixEntry 1 } cwspPrefixRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Used to create, delete, activate and de-activate network prefixes used in ILMI address registration." ::= { cwspPrefixEntry 2 } -- the port address table cwspAddressTable OBJECT-TYPE SYNTAX SEQUENCE OF CwspAddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Interface ATM Address Table. This table contains all the attributes necessary to determine what the PNNI entity believes is reachable in terms of ATM End System Addresses and to determine which nodes are advertising this reachability. This table is also used to configure static routes to reachable addresses. Entries in this table can be created/deleted by setting the intfAddressRowStatus object to appropriate values. Existing entries in this table cannot be modified. Entries in this table can also be created/deleted through the command provided by the CLI." ::= { cwspAddress 1 } cwspAddressEntry OBJECT-TYPE SYNTAX CwspAddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table, containing information about a reachable address." INDEX { ifIndex, cwspAtmAddress, cwspAddrLen } ::= { cwspAddressTable 1 } CwspAddressEntry ::= SEQUENCE { cwspAtmAddress AtmAddress, cwspAddrLen INTEGER, cwspAddrType INTEGER, cwspAddrProto INTEGER, cwspAddrPlan INTEGER, cwspAddrScope INTEGER, cwspAddrRedistribute TruthValue, cwspAddressRowStatus RowStatus } cwspAtmAddress OBJECT-TYPE SYNTAX AtmAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of the ATM End System Address." ::= { cwspAddressEntry 1 } cwspAddrLen OBJECT-TYPE SYNTAX INTEGER (0..160) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address length in bits to be applied to the ATM End System Address." ::= { cwspAddressEntry 2 } cwspAddrType OBJECT-TYPE SYNTAX INTEGER { internal(1), exterior(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of reachability from the advertising node to the address. This variable indicates either this ATM address ('internal') is a reachable ATM destination that is directly attached to the logical node advertising this address or an ATM address('exterior') that can be reached through a PNNI routing domain but which is not located in that routing domain." REFERENCE "ATM Forum PNNI 1.0 Section 5.8.1.3" DEFVAL { exterior } ::= { cwspAddressEntry 3 } cwspAddrProto OBJECT-TYPE SYNTAX INTEGER { local(1), static(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The routing mechanism via which the connectivity from the advertising node to the reachable address was learned. A 'local' address indicates this address is automatically advertised. A 'static' address is not automatically advertised. By setting 'cwspAddrRedistribute' variable (see below) to 'true' will force a 'static' address to be advertised." DEFVAL { local } ::= { cwspAddressEntry 4 } cwspAddrPlan OBJECT-TYPE SYNTAX INTEGER { e164(1), nsap(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The address plan. For NSAP address, the first byte of the address automatically implies one of the three NSAP address plans: NSAP E.164, NSAP DCC or NSAP ICD." DEFVAL { nsap } ::= { cwspAddressEntry 5 } cwspAddrScope OBJECT-TYPE SYNTAX INTEGER (0..104) MAX-ACCESS read-create STATUS current DESCRIPTION "The PNNI scope of advertisement (i.e. level of PNNI hierarchy) of the reachability from the advertising node to the address." DEFVAL { 0 } ::= { cwspAddressEntry 6 } cwspAddrRedistribute OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Whether or not the reachable address specified by this entry is to be advertised by the local node into its PNNI routing domain. This object is only meaningful if the routing mechanism (cwspAddrProto) is static." DEFVAL { false } ::= { cwspAddressEntry 7 } cwspAddressRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "To create or delete a reachable address. Note that NMS should use CreateAndGo to create a row and Destroy to delete a row. The managed device will return active or notInService as row status." ::= { cwspAddressEntry 8 } -- the UNI port registered address cwspRegAddressTable OBJECT-TYPE SYNTAX SEQUENCE OF CwspRegAddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains a list of ATM addresses that can be used for calls to and from a given interface by a switch or service. The ATM addresses are registered by the endsystem via ILMI. ILMI registered addresses cannot be deleted using this table. This table only applies to switches and network services." ::= { cwspRegAddress 1 } cwspRegAddressEntry OBJECT-TYPE SYNTAX CwspRegAddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the ATM Interface Registered Address table." INDEX { ifIndex, cwspRegAtmAddress } ::= { cwspRegAddressTable 1 } CwspRegAddressEntry ::= SEQUENCE { cwspRegAtmAddress AtmAddress, cwspRegAddressOrgSscope INTEGER } cwspRegAtmAddress OBJECT-TYPE SYNTAX AtmAddress MAX-ACCESS read-only STATUS current DESCRIPTION "An address registered for a given switch or service interface." ::= { cwspRegAddressEntry 1 } cwspRegAddressOrgSscope OBJECT-TYPE SYNTAX INTEGER { localNetwork(1), global(15) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the organizational scope for the referenced address. The information of the referenced address shall not be distributed outside the indicated scope. The default values for organizational scope are localNetwork(1) for ATM group addresses, and global(15) for individual addresses." DEFVAL { global } ::= { cwspRegAddressEntry 2 } -- the port CAC configuration Table cwspCacConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF CwspCacConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table specifying the CAC(Connection Admission Control) information for each interface." ::= { cwspCacConfig 1 } cwspCacConfigEntry OBJECT-TYPE SYNTAX CwspCacConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry contains CAC information." INDEX { ifIndex } ::= { cwspCacConfigTable 1 } CwspCacConfigEntry ::= SEQUENCE { cwspUtilFactorCbr Integer32, cwspUtilFactorRtVbr Integer32, cwspUtilFactorNrtVbr Integer32, cwspUtilFactorAbr Integer32, cwspUtilFactorUbr Integer32, cwspMaxBwCbr Integer32, cwspMaxBwRtVbr Integer32, cwspMaxBwNrtVbr Integer32, cwspMaxBwAbr Integer32, cwspMaxBwUbr Integer32, cwspMinBwCbr Integer32, cwspMinBwRtVbr Integer32, cwspMinBwNrtVbr Integer32, cwspMinBwAbr Integer32, cwspMinBwUbr Integer32, cwspMaxVcCbr Integer32, cwspMaxVcRtVbr Integer32, cwspMaxVcNrtVbr Integer32, cwspMaxVcAbr Integer32, cwspMaxVcUbr Integer32, cwspMinVcCbr Integer32, cwspMinVcRtVbr Integer32, cwspMinVcNrtVbr Integer32, cwspMinVcAbr Integer32, cwspMinVcUbr Integer32, cwspMaxVcBwCbr Integer32, cwspMaxVcBwRtVbr Integer32, cwspMaxVcBwNrtVbr Integer32, cwspMaxVcBwAbr Integer32, cwspMaxVcBwUbr Integer32, cwspDefaultCdvtCbr Integer32, cwspDefaultCdvtRtVbr Integer32, cwspDefaultCdvtNrtVbr Integer32, cwspDefaultCdvtAbr Integer32, cwspDefaultCdvtUbr Integer32, cwspDefaultMbsRtVbr Integer32, cwspDefaultMbsNrtVbr Integer32 } cwspUtilFactorCbr OBJECT-TYPE SYNTAX Integer32 (1..200) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the booking factor for CBR service." DEFVAL { 100 } ::= { cwspCacConfigEntry 1 } cwspUtilFactorRtVbr OBJECT-TYPE SYNTAX Integer32 (1..200) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the booking factor for real time VBR service" DEFVAL { 100 } ::= { cwspCacConfigEntry 2 } cwspUtilFactorNrtVbr OBJECT-TYPE SYNTAX Integer32 (1..200) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the booking factor for non-real time VBR service " DEFVAL { 100 } ::= { cwspCacConfigEntry 3 } cwspUtilFactorAbr OBJECT-TYPE SYNTAX Integer32 (1..200) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the booking factor for ABR service" DEFVAL { 100 } ::= { cwspCacConfigEntry 4 } cwspUtilFactorUbr OBJECT-TYPE SYNTAX Integer32 (1..200) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the booking factor for UBR service." DEFVAL { 100 } ::= { cwspCacConfigEntry 5 } cwspMaxBwCbr OBJECT-TYPE SYNTAX Integer32 (0..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the maximum bandwidth for CBR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%." DEFVAL { 1000000 } ::= { cwspCacConfigEntry 6 } cwspMaxBwRtVbr OBJECT-TYPE SYNTAX Integer32 (0..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the maximum bandwidth for real time VBR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%." DEFVAL { 1000000 } ::= { cwspCacConfigEntry 7 } cwspMaxBwNrtVbr OBJECT-TYPE SYNTAX Integer32 (0..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the maximum bandwidth for non-real time VBR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%." DEFVAL { 1000000 } ::= { cwspCacConfigEntry 8 } cwspMaxBwAbr OBJECT-TYPE SYNTAX Integer32 (0..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the maximum bandwidth for ABR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%." DEFVAL { 1000000 } ::= { cwspCacConfigEntry 9 } cwspMaxBwUbr OBJECT-TYPE SYNTAX Integer32 (0..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the maximum bandwidth for UBR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%." DEFVAL { 1000000 } ::= { cwspCacConfigEntry 10 } cwspMinBwCbr OBJECT-TYPE SYNTAX Integer32 (0..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the minimum bandwidth for CBR service in percentage. The total values of cwspMinBwCbr, cwspMinBwRtVbr, cwspMinBwNrtVbr, cwspMinBwAbr and cwspMinBwUbr can not exceed 1000000, i.e. 100%. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%." DEFVAL { 0 } ::= { cwspCacConfigEntry 11 } cwspMinBwRtVbr OBJECT-TYPE SYNTAX Integer32 (0..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the minimum bandwidth for real time VBR service in percentage. The total values of cwspMinBwCbr, cwspMinBwRtVbr, cwspMinBwNrtVbr, cwspMinBwAbr and cwspMinBwUbr can not exceed 1000000, i.e. 100%. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%." DEFVAL { 0 } ::= { cwspCacConfigEntry 12 } cwspMinBwNrtVbr OBJECT-TYPE SYNTAX Integer32 (0..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the minimum bandwidth for non-real time VBR service in percentage. The total values of cwspMinBwCbr, cwspMinBwRtVbr, cwspMinBwNrtVbr, cwspMinBwAbr and cwspMinBwUbr can not exceed 1000000, i.e. 100%. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%." DEFVAL { 0 } ::= { cwspCacConfigEntry 13 } cwspMinBwAbr OBJECT-TYPE SYNTAX Integer32 (0..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the minimum bandwidth for ABR service in percentage. The total values of cwspMinBwCbr, cwspMinBwRtVbr, cwspMinBwNrtVbr, cwspMinBwAbr and cwspMinBwUbr can not exceed 1000000, i.e. 100%. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%." DEFVAL { 0 } ::= { cwspCacConfigEntry 14 } cwspMinBwUbr OBJECT-TYPE SYNTAX Integer32(0..1000000) MAX-ACCESS read-only STATUS current DESCRIPTION "This is the minimum bandwidth for UBR service in percentage. The value for this variable is always 0." ::= { cwspCacConfigEntry 15 } cwspMaxVcCbr OBJECT-TYPE SYNTAX Integer32 (0..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the maximum number of VCs for CBR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%. " DEFVAL { 1000000 } ::= { cwspCacConfigEntry 16 } cwspMaxVcRtVbr OBJECT-TYPE SYNTAX Integer32 (0..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the maximum number of VCs for real time VBR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%." DEFVAL { 1000000 } ::= { cwspCacConfigEntry 17 } cwspMaxVcNrtVbr OBJECT-TYPE SYNTAX Integer32 (0..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the maximum number of VCs for non-real time VBR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%." DEFVAL { 1000000 } ::= { cwspCacConfigEntry 18 } cwspMaxVcAbr OBJECT-TYPE SYNTAX Integer32 (0..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the maximum number of VCs for ABR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%. " DEFVAL { 1000000 } ::= { cwspCacConfigEntry 19 } cwspMaxVcUbr OBJECT-TYPE SYNTAX Integer32 (0..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the maximum number of VCs for UBR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%." DEFVAL { 1000000 } ::= { cwspCacConfigEntry 20 } cwspMinVcCbr OBJECT-TYPE SYNTAX Integer32 (0..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the minimum number of VCs for CBR service in percentage. The values of cwspMinVcCbr, cwspMinVcRtVbr, cwspMinVcNrtVbr, cwspMinVcAbr and cwspMinVcUbr can not exceed 1000000, i.e. 100%. This variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%." DEFVAL { 0 } ::= { cwspCacConfigEntry 21 } cwspMinVcRtVbr OBJECT-TYPE SYNTAX Integer32 (0..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the minimum number of VCs for real time VBR service in percentage. The values of cwspMinVcCbr, cwspMinVcRtVbr, cwspMinVcNrtVbr, cwspMinVcAbr and cwspMinVcUbr can not exceed 1000000, i.e. 100%. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%." DEFVAL { 0 } ::= { cwspCacConfigEntry 22 } cwspMinVcNrtVbr OBJECT-TYPE SYNTAX Integer32 (0..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the minimum number of VCs for non-real time VBR service in percentage. The values of cwspMinVcCbr, cwspMinVcRtVbr, cwspMinVcNrtVbr,cwspMinVcAbr and cwspMinVcUbr can not exceed 1000000, i.e. 100%. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%." DEFVAL { 0 } ::= { cwspCacConfigEntry 23 } cwspMinVcAbr OBJECT-TYPE SYNTAX Integer32 (0..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the minimum number of VCs for ABR service in percentage. The values of cwspMinVcCbr, cwspMinVcRtVbr, cwspMinVcNrtVbr, cwspMinVcAbr and cwspMinVcUbr can not exceed 1000000, i.e. 100%. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%." DEFVAL { 0 } ::= { cwspCacConfigEntry 24 } cwspMinVcUbr OBJECT-TYPE SYNTAX Integer32 (0..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the minimum number of VCs for UBR service in percentage. The values of cwspMinVcCbr, cwspMinVcRtVbr, cwspMinVcNrtVbr, cwspMinVcAbr and cwspMinVcUbr can not exceed 1000000, i.e. 100%. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%." DEFVAL { 0 } ::= { cwspCacConfigEntry 25 } cwspMaxVcBwCbr OBJECT-TYPE SYNTAX Integer32 (0..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the maximum bandwidth allowed for a VC for real time CBR service. The value is in the unit of cells per second." DEFVAL { 0 } ::= { cwspCacConfigEntry 26 } cwspMaxVcBwRtVbr OBJECT-TYPE SYNTAX Integer32 (0..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the maximum bandwidth allowed for a VC for real time VBR service. The value is in the unit of cells per second." DEFVAL { 0 } ::= { cwspCacConfigEntry 27 } cwspMaxVcBwNrtVbr OBJECT-TYPE SYNTAX Integer32 (0..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the maximum bandwidth allowed for a VC for non-real time VBR service. The value is in the unit of cells per second." DEFVAL { 0 } ::= { cwspCacConfigEntry 28 } cwspMaxVcBwAbr OBJECT-TYPE SYNTAX Integer32 (0..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the maximum bandwidth allowed for a VC for ABR service. The value is in the unit of cells per second. " DEFVAL { 0 } ::= { cwspCacConfigEntry 29 } cwspMaxVcBwUbr OBJECT-TYPE SYNTAX Integer32 (0..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the maximum bandwidth allowed for UBR service. The value is in the unit of cells per second." DEFVAL { 0 } ::= { cwspCacConfigEntry 30 } cwspDefaultCdvtCbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the default CDVT for CBR service." DEFVAL { 1024 } ::= { cwspCacConfigEntry 31 } cwspDefaultCdvtRtVbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the default CDVT real time VBR service." DEFVAL { 1024 } ::= { cwspCacConfigEntry 32 } cwspDefaultCdvtNrtVbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the default CDVT non-real time VBR service." DEFVAL { 1024 } ::= { cwspCacConfigEntry 33 } cwspDefaultCdvtAbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the default CDVT for ABR service." DEFVAL { 1024 } ::= { cwspCacConfigEntry 34 } cwspDefaultCdvtUbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the default CDVT for UBR service." DEFVAL { 1024 } ::= { cwspCacConfigEntry 35 } cwspDefaultMbsRtVbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the default MBS real time VBR service." DEFVAL { 1024 } ::= { cwspCacConfigEntry 36 } cwspDefaultMbsNrtVbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the default MBS non-real time VBR service." DEFVAL { 1024 } ::= { cwspCacConfigEntry 37 } -- the port loading table cwspLoadTable OBJECT-TYPE SYNTAX SEQUENCE OF CwspLoadEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table specifying the load information for each interface." ::= { cwspLoad 1 } cwspLoadEntry OBJECT-TYPE SYNTAX CwspLoadEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry contains the load information." INDEX { ifIndex } ::= { cwspLoadTable 1 } CwspLoadEntry ::= SEQUENCE { cwspLoadBwTotal Integer32, cwspLoadMaxBwCbr Integer32, cwspLoadMaxBwRtVbr Integer32, cwspLoadMaxBwNrtVbr Integer32, cwspLoadMaxBwAbr Integer32, cwspLoadMaxBwUbr Integer32, cwspLoadBwAvail Integer32, cwspLoadAvlBwCbr Integer32, cwspLoadAvlBwRtVbr Integer32, cwspLoadAvlBwNrtVbr Integer32, cwspLoadAvlBwAbr Integer32, cwspLoadAvlBwUbr Integer32, cwspLoadVcAvail Integer32, cwspLoadAvlVcCbr Integer32, cwspLoadAvlVcRtVbr Integer32, cwspLoadAvlVcNrtVbr Integer32, cwspLoadAvlVcAbr Integer32, cwspLoadAvlVcUbr Integer32, cwspLoadCtdCbr Integer32, cwspLoadCtdRtVbr Integer32, cwspLoadCtdNrtVbr Integer32, cwspLoadCtdAbr Integer32, cwspLoadCtdUbr Integer32, cwspLoadCdvCbr Integer32, cwspLoadCdvRtVbr Integer32, cwspLoadCdvNrtVbr Integer32, cwspLoadCdvAbr Integer32, cwspLoadCdvUbr Integer32, cwspLoadClr0Cbr Integer32, cwspLoadClr0RtVbr Integer32, cwspLoadClr0NrtVbr Integer32, cwspLoadClr0Abr Integer32, cwspLoadClr0Ubr Integer32, cwspLoadClr01Cbr Integer32, cwspLoadClr01RtVbr Integer32, cwspLoadClr01NrtVbr Integer32, cwspLoadClr01Abr Integer32, cwspLoadClr01Ubr Integer32, cwspLoadMinGurCrCbr Integer32, cwspLoadMinGurCrRtVbr Integer32, cwspLoadMinGurCrNrtVbr Integer32, cwspLoadMinGurCrAbr Integer32, cwspLoadMinGurCrUbr Integer32 } cwspLoadBwTotal OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The total bandwidth of the interface." ::= { cwspLoadEntry 1 } cwspLoadMaxBwCbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The Maximum bandwith for CBR service." ::= { cwspLoadEntry 2 } cwspLoadMaxBwRtVbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum bandwith for real time VBR service." ::= { cwspLoadEntry 3 } cwspLoadMaxBwNrtVbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum bandwith for non-real time VBR service." ::= { cwspLoadEntry 4 } cwspLoadMaxBwAbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum bandwith for ABR service." ::= { cwspLoadEntry 5 } cwspLoadMaxBwUbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION " The maximum bandwith for UBR service." ::= { cwspLoadEntry 6 } cwspLoadBwAvail OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The total available bandwidth of the interface." ::= { cwspLoadEntry 7 } cwspLoadAvlBwCbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The available bandwith for CBR service." ::= { cwspLoadEntry 8 } cwspLoadAvlBwRtVbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The available bandwith for real time VBR service." ::= { cwspLoadEntry 9 } cwspLoadAvlBwNrtVbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The available bandwith for non-real time VBR service." ::= { cwspLoadEntry 10 } cwspLoadAvlBwAbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The available bandwith for ABR service." ::= { cwspLoadEntry 11 } cwspLoadAvlBwUbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION " The available bandwith for UBR service." ::= { cwspLoadEntry 12 } cwspLoadVcAvail OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of available VCs of the interface." ::= { cwspLoadEntry 13 } cwspLoadAvlVcCbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION " The number of VCs used by CBR service." ::= { cwspLoadEntry 14 } cwspLoadAvlVcRtVbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of VCs used by real time VBR service." ::= { cwspLoadEntry 15 } cwspLoadAvlVcNrtVbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of VCs used by non-real time VBR service." ::= { cwspLoadEntry 16 } cwspLoadAvlVcAbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of VCs used by ABR service." ::= { cwspLoadEntry 17 } cwspLoadAvlVcUbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION " The number of VCs used by UBR service." ::= { cwspLoadEntry 18 } cwspLoadCtdCbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION " The cell transfer delay of CBR service." ::= { cwspLoadEntry 19 } cwspLoadCtdRtVbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The cell transfer delay of real time VBR service." ::= { cwspLoadEntry 20 } cwspLoadCtdNrtVbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The cell transfer delay of non-real time VBR service." ::= { cwspLoadEntry 21 } cwspLoadCtdAbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The cell transfer delay of ABR service." ::= { cwspLoadEntry 22 } cwspLoadCtdUbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION " The cell transfer delay of UBR service." ::= { cwspLoadEntry 23 } cwspLoadCdvCbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION " The cell delay variation of CBR service." ::= { cwspLoadEntry 24 } cwspLoadCdvRtVbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The cell delay variation of real time VBR service." ::= { cwspLoadEntry 25 } cwspLoadCdvNrtVbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The cell delay variation of non-real time VBR service." ::= { cwspLoadEntry 26 } cwspLoadCdvAbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The cell delay variation of ABR service." ::= { cwspLoadEntry 27 } cwspLoadCdvUbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION " The cell delay variation of UBR service." ::= { cwspLoadEntry 28 } cwspLoadClr0Cbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION " The cell loss ratio-0 of CBR service, -1 implies N/A." ::= { cwspLoadEntry 29 } cwspLoadClr0RtVbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The cell loss ratio-0 of real time VBR service, -1 implies N/A." ::= { cwspLoadEntry 30 } cwspLoadClr0NrtVbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The cell loss ratio-0 of non-real time VBR service, -1 implies N/A." ::= { cwspLoadEntry 31 } cwspLoadClr0Abr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The cell loss ratio-0 of ABR service, -1 implies N/A." ::= { cwspLoadEntry 32 } cwspLoadClr0Ubr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION " The cell loss ratio-0 of UBR service, -1 implies N/A." ::= { cwspLoadEntry 33 } cwspLoadClr01Cbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION " The cell loss ratio-1 of CBR service, -1 implies N/A." ::= { cwspLoadEntry 34 } cwspLoadClr01RtVbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The cell loss ratio-1 of real time VBR service, -1 implies N/A." ::= { cwspLoadEntry 35 } cwspLoadClr01NrtVbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The cell loss ratio-1 of non-real time VBR service, -1 implies N/A." ::= { cwspLoadEntry 36 } cwspLoadClr01Abr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The cell loss ratio-1 of ABR service, -1 implies N/A." ::= { cwspLoadEntry 37 } cwspLoadClr01Ubr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION " The cell loss ratio-1 of UBR service, -1 implies N/A." ::= { cwspLoadEntry 38 } cwspLoadMinGurCrCbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION " The minimum guaranteed cell rate capacity of CBR service." ::= { cwspLoadEntry 39 } cwspLoadMinGurCrRtVbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum guaranteed cell rate capacity of real time VBR service." ::= { cwspLoadEntry 40 } cwspLoadMinGurCrNrtVbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum guaranteed cell rate capacity of non-real time VBR service." ::= { cwspLoadEntry 41 } cwspLoadMinGurCrAbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum guaranteed cell rate capacity of ABR service." ::= { cwspLoadEntry 42 } cwspLoadMinGurCrUbr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum guaranteed cell rate capacity of UBR service." ::= { cwspLoadEntry 43 } -- the port call table cwspCallTable OBJECT-TYPE SYNTAX SEQUENCE OF CwspCallEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This Table contains the objects which show parameters associated with a Point-to-Point(p2p) or Point-to-MultiPoint (p2mp) SVC/SPVC call." ::= { cwspCall 1 } cwspCallEntry OBJECT-TYPE SYNTAX CwspCallEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object shows the multiple key index to get the Call record information. The key comprise of Interface Index, VPI/VCI value and Call Reference Value for the call." INDEX { ifIndex, cwspCallVpi, cwspCallVci, cwspCallLeafReference } ::= { cwspCallTable 1 } CwspCallEntry ::= SEQUENCE { cwspCallVpi Integer32, cwspCallVci Integer32, cwspCallLeafReference Integer32, cwspCallCallRef Integer32, cwspCallCallingAddress AtmAddress, cwspCallCalledAddress AtmAddress, cwspCallCallingSubAddr AtmAddress, cwspCallCalledSubAddr AtmAddress, cwspCallOtherIntfIndex Integer32, cwspCallOtherIntfVpi Integer32, cwspCallOtherIntfVci Integer32, cwspCallOtherIntfCallRef Integer32, cwspCallType INTEGER, cwspCallStartTime TimeStamp, cwspCallBearerClass INTEGER, cwspCallServiceCategory INTEGER, cwspCallCastType INTEGER, cwspCallClipSusceptibility INTEGER, cwspCallFwdConformance INTEGER, cwspCallFwdPcr Integer32, cwspCallFwdScr Integer32, cwspCallFwdMbs Integer32, cwspCallFwdCdvt Integer32, cwspCallFwdFrameDiscard INTEGER, cwspCallBwdConformance INTEGER, cwspCallBwdPcr Integer32, cwspCallBwdScr Integer32, cwspCallBwdMbs Integer32, cwspCallBwdCdvt Integer32, cwspCallBwdFrameDiscard INTEGER, cwspCallMaxCtd Integer32, cwspCallMaxFwdCdv Integer32, cwspCallMaxFwdClr Integer32, cwspCallMaxBwdCdv Integer32, cwspCallMaxBwdClr Integer32 } cwspCallVpi OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object shows the VPI value of the call on this interface." ::= { cwspCallEntry 1 } cwspCallVci OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object shows The VCI value of the call on this interface. The value should be in the range of 32-65535 (0=SPVP)." ::= { cwspCallEntry 2 } cwspCallLeafReference OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object shows the value of the Leaf Reference (EndPointReference) of the Call on this interface." ::= { cwspCallEntry 3 } cwspCallCallRef OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the Call Reference value of the call on this interface." ::= { cwspCallEntry 4 } cwspCallCallingAddress OBJECT-TYPE SYNTAX AtmAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the Calling Party Address of the call." ::= { cwspCallEntry 5 } cwspCallCalledAddress OBJECT-TYPE SYNTAX AtmAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the Called Party Address of the call." ::= { cwspCallEntry 6 } cwspCallCallingSubAddr OBJECT-TYPE SYNTAX AtmAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the Calling Party Subaddress of the call." ::= { cwspCallEntry 7 } cwspCallCalledSubAddr OBJECT-TYPE SYNTAX AtmAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the Called Party Subaddress of the call." ::= { cwspCallEntry 8 } cwspCallOtherIntfIndex OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the Other Interface of the call. Generally, this would be the outgoing/egress interface for the call." ::= { cwspCallEntry 9 } cwspCallOtherIntfVpi OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the VPI of the call on the partner interface." ::= { cwspCallEntry 10 } cwspCallOtherIntfVci OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows The VCI of the call on the partner o interface. The value should be in the range of 32-65535 (0=SPVP)." ::= { cwspCallEntry 11 } cwspCallOtherIntfCallRef OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the Call Reference of the call on the partner interface." ::= { cwspCallEntry 12 } cwspCallType OBJECT-TYPE SYNTAX INTEGER { svc(1), spvc(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the Call Type for the call on this interface. The call type could be SVC or SPVC." ::= { cwspCallEntry 13 } cwspCallStartTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the start time of the call. This is the timestamp when the Setup Message (or Add Party Message) was first received on this interface." ::= { cwspCallEntry 14 } cwspCallBearerClass OBJECT-TYPE SYNTAX INTEGER { bcobA(1), bcobC(2), bcobX(3), vp(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the Bearer Class of the Call. It could be BcobA, BcobC, BcobX or VP Service" ::= { cwspCallEntry 15 } cwspCallServiceCategory OBJECT-TYPE SYNTAX INTEGER { cbr(1), rtVbr(2), nrtVbr(3), abr(4), ubr(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the service category of the call, which can be CBR, rtVBR, nrtVBR, ABR or UBR" ::= { cwspCallEntry 16 } cwspCallCastType OBJECT-TYPE SYNTAX INTEGER { p2p(1), p2mp(2), mp2p(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the Cast Type of the call, which can be a Point-to-Point (p2p), Point-to-MultiPoint (p2mp) or MultiPoint-to-Point (mp2p) call." ::= { cwspCallEntry 17 } cwspCallClipSusceptibility OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows Susceptibility to Clipping. It can be susceptible or not susceptible." ::= { cwspCallEntry 18 } cwspCallFwdConformance OBJECT-TYPE SYNTAX INTEGER { cbr1(1), cbr2(2), cbr3(3), vbr1(4), vbr2(5), vbr3(6), abr(7), ubr1(8), ubr2(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the conformance of the call to the traffic sets in the forward direction. It can be CBR.1, CBR.2, CBR.3, VBR.1 VBR.2, VBR.3, ABR, UBR.1 or UBR.2. This is as defined in ATMF Traffic Management 4.0 specification." ::= { cwspCallEntry 19 } cwspCallFwdPcr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the Peak Cell Rate(pcr) in the forward direction of the call." ::= { cwspCallEntry 20 } cwspCallFwdScr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the Sustainable Cell Rate(scr) in the forward direction of the call." ::= { cwspCallEntry 21 } cwspCallFwdMbs OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the Maximum Burst Size(mbs) of the call in the forward direction." ::= { cwspCallEntry 22 } cwspCallFwdCdvt OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the Cell Delay Variation Tolerance(cdvt) in the forward direction for the call, for PCR and SCR." ::= { cwspCallEntry 23 } cwspCallFwdFrameDiscard OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows if the Frame Discard is enabled or disabled in the forward direction for the call" ::= { cwspCallEntry 24 } cwspCallBwdConformance OBJECT-TYPE SYNTAX INTEGER { cbr1(1), cbr2(2), cbr3(3), vbr1(4), vbr2(5), vbr3(6), abr(7), ubr1(8), ubr2(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the conformance of the call to the traffic sets in the backward direction. It can be CBR.1, CBR.2, CBR.3, VBR.1 VBR.2, VBR.3, ABR, UBR.1 or UBR.2. This is as defined in ATMF Traffic Management 4.0 specification." ::= { cwspCallEntry 25 } cwspCallBwdPcr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the Peak Cell Rate in the backward direction of the call." ::= { cwspCallEntry 26 } cwspCallBwdScr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the Sustainable Cell Rate in the backward direction of the call." ::= { cwspCallEntry 27 } cwspCallBwdMbs OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the Maximum Burst Size of the call in the backward direction." ::= { cwspCallEntry 28 } cwspCallBwdCdvt OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the Cell Delay Variation Tolerance in the backward direction for the call, for PCR and SCR." ::= { cwspCallEntry 29 } cwspCallBwdFrameDiscard OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows if the Frame Discard is enabled or disabled in the backward direction for the call." ::= { cwspCallEntry 30 } cwspCallMaxCtd OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the Maximum Cell Transfer Delay for the call on this interface." ::= { cwspCallEntry 31 } cwspCallMaxFwdCdv OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the Maximum Cell Delay Variation in the forward direction for this call on this interface." ::= { cwspCallEntry 32 } cwspCallMaxFwdClr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the Maximum Cell Loss Ratio in the forward direction for this call on this interface." ::= { cwspCallEntry 33 } cwspCallMaxBwdCdv OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the Maximum Cell Delay Variation in the backward direction for this call on this interface." ::= { cwspCallEntry 34 } cwspCallMaxBwdClr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the Maximum Cell Loss Ratio in the backward direction for this call on this interface." ::= { cwspCallEntry 35 } -- the port ABR call table cwspAbrCallTable OBJECT-TYPE SYNTAX SEQUENCE OF CwspAbrCallEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information for ABR calls on an interface." ::= { cwspAbrCall 1 } cwspAbrCallEntry OBJECT-TYPE SYNTAX CwspAbrCallEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table, containing information about an ABR call." INDEX { ifIndex, cwspAbrCallVpi, cwspAbrCallVci } ::= { cwspAbrCallTable 1 } CwspAbrCallEntry ::= SEQUENCE { cwspAbrCallVpi Integer32, cwspAbrCallVci Integer32, cwspAbrCallCallRef Integer32, cwspAbrCallClgAddress AtmAddress, cwspAbrCallCldAddress AtmAddress, cwspAbrCallClgSubAddr AtmAddress, cwspAbrCallCldSubAddr AtmAddress, cwspAbrCallOtherIntfIndex Integer32, cwspAbrCallOtherIntfVpi Integer32, cwspAbrCallOtherIntfVci Integer32, cwspAbrCallOtherIntfCallRef Integer32, cwspAbrCallType INTEGER, cwspAbrCallStartTime TimeStamp, cwspAbrCallBearerClass INTEGER, cwspAbrCallServiceCategory INTEGER, cwspAbrCallCastType INTEGER, cwspAbrCallClipSusceptibility INTEGER, cwspAbrCallFwdConformance INTEGER, cwspAbrCallFwdPcr Integer32, cwspAbrCallFwdMcr Integer32, cwspAbrCallFwdIcr Integer32, cwspAbrCallFwdRif INTEGER, cwspAbrCallFwdRdf INTEGER, cwspAbrCallFwdTbe Integer32, cwspAbrCallFwdNrm INTEGER, cwspAbrCallFwdTrm INTEGER, cwspAbrCallFwdAdtf Integer32, cwspAbrCallFwdCdf INTEGER, cwspAbrCallFwdFrameDiscard INTEGER, cwspAbrCallBwdPcr Integer32, cwspAbrCallBwdMcr Integer32, cwspAbrCallBwdIcr Integer32, cwspAbrCallBwdRif INTEGER, cwspAbrCallBwdRdf INTEGER, cwspAbrCallBwdTbe Integer32, cwspAbrCallBwdNrm INTEGER, cwspAbrCallBwdTrm INTEGER, cwspAbrCallBwdAdtf Integer32, cwspAbrCallBwdCdf INTEGER, cwspAbrCallBwdFrameDiscard INTEGER, cwspAbrCallFrtt Integer32, cwspAbrCallMaxCtd Integer32, cwspAbrCallMaxFwdCdv Integer32, cwspAbrCallMaxFwdClr Integer32, cwspAbrCallMaxBwdCdv Integer32, cwspAbrCallMaxBwdClr Integer32 } cwspAbrCallVpi OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VPI value of the ABR call on this interface." ::= { cwspAbrCallEntry 1 } cwspAbrCallVci OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VCI value of the ABR call on this interface. The value should be in the range of 32-65535 (0=SPVP)." ::= { cwspAbrCallEntry 2 } cwspAbrCallCallRef OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The Call Reference value of the ABR call on this interface." ::= { cwspAbrCallEntry 3 } cwspAbrCallClgAddress OBJECT-TYPE SYNTAX AtmAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Calling Party Address of the ABR call." ::= { cwspAbrCallEntry 4 } cwspAbrCallCldAddress OBJECT-TYPE SYNTAX AtmAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Called Party Address of the ABR call." ::= { cwspAbrCallEntry 5 } cwspAbrCallClgSubAddr OBJECT-TYPE SYNTAX AtmAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Calling Party Subaddress of the ABR call." ::= { cwspAbrCallEntry 6 } cwspAbrCallCldSubAddr OBJECT-TYPE SYNTAX AtmAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Called Party Subaddress of the ABR call." ::= { cwspAbrCallEntry 7 } cwspAbrCallOtherIntfIndex OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The Other Interface ID of the ABR call. Generally this would be the outgoing/egress interface for the call." ::= { cwspAbrCallEntry 8 } cwspAbrCallOtherIntfVpi OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-only STATUS current DESCRIPTION "The VPI value of the ABR call on the partner interface." ::= { cwspAbrCallEntry 9 } cwspAbrCallOtherIntfVci OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The VCI value of the ABR call on the partner interface. The value should be in the range of 32-65535 (0=SPVP)." ::= { cwspAbrCallEntry 10 } cwspAbrCallOtherIntfCallRef OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The Call Reference of the ABR call on the partner interface." ::= { cwspAbrCallEntry 11 } cwspAbrCallType OBJECT-TYPE SYNTAX INTEGER { svc(1), spvc(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Call Type for the ABR call on this interface. The call type could be SVC or SPVC." ::= { cwspAbrCallEntry 12 } cwspAbrCallStartTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The start time of the ABR call. This is the timestamp when the Setup Message (or Add Party Message) was first received on this interface." ::= { cwspAbrCallEntry 13 } cwspAbrCallBearerClass OBJECT-TYPE SYNTAX INTEGER { bcobA(1), bcobC(2), bcobX(3), vp(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Bearer Class of the ABR call. It could be BCOB-A, BCOB-C, BCOB-X or VP Service." ::= { cwspAbrCallEntry 14 } cwspAbrCallServiceCategory OBJECT-TYPE SYNTAX INTEGER { abr(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Service Category of the ABR call, which is ABR." ::= { cwspAbrCallEntry 15 } cwspAbrCallCastType OBJECT-TYPE SYNTAX INTEGER { p2p(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Cast Type of the ABR call, which can only be Point-to-Point(p2p) call." ::= { cwspAbrCallEntry 16 } cwspAbrCallClipSusceptibility OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Susceptibility to Clipping. It can be susceptible or not susceptible." ::= { cwspAbrCallEntry 17 } cwspAbrCallFwdConformance OBJECT-TYPE SYNTAX INTEGER { abr(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Conformance of the ABR call to the traffic sets in the forward direction. It can only be ABR as defined in ATMF Traffic Management 4.0 specification." ::= { cwspAbrCallEntry 18 } cwspAbrCallFwdPcr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The Peak Cell Rate for the ABR call in the forward direction." ::= { cwspAbrCallEntry 19 } cwspAbrCallFwdMcr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The Minimum Cell Rate for the ABR call in the forward direction." ::= { cwspAbrCallEntry 20 } cwspAbrCallFwdIcr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The Initial Cell Rate for the ABR call in the forward direction. This is the rate at which the source starts, both initially and after an idle period. The value must not be larger than PCR, and is usually lower." ::= { cwspAbrCallEntry 21 } cwspAbrCallFwdRif OBJECT-TYPE SYNTAX INTEGER { rifOneOver32768(1), rifOneOver16384(2), rifOneOver8192(3), rifOneOver4096(4), rifOneOver2048(5), rifOneOver1024(6), rifOneOver512(7), rifOneOver256(8), rifOneOver128(9), rifOneOver64(10), rifOneOver32(11), rifOneOver16(12), rifOneOver8(13), rifOneOver4(14), rifOneOver2(15), rifOne(16) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Rate Increase Factor for the ABR call in the forward direction. This controls the rate at which the rate increases, when a backward RM-cell is received with CI=0 and NI=0. Larger values lead to faster rate increase. The default value is rifOneOver16(12)." ::= { cwspAbrCallEntry 22 } cwspAbrCallFwdRdf OBJECT-TYPE SYNTAX INTEGER { rdfOneOver32768(1), rdfOneOver16384(2), rdfOneOver8192(3), rdfOneOver4096(4), rdfOneOver2048(5), rdfOneOver1024(6), rdfOneOver512(7), rdfOneOver256(8), rdfOneOver128(9), rdfOneOver64(10), rdfOneOver32(11), rdfOneOver16(12), rdfOneOver8(13), rdfOneOver4(14), rdfOneOver2(15), rdfOne(16) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Rate Decrease Factor for the ABR call in the forward direction. This controls the rate decrease which occurs when backward RM-cells with CI=1, are received. Larger values lead to faster rate decrease. The default value is rdfOneOver16(12)." ::= { cwspAbrCallEntry 23 } cwspAbrCallFwdTbe OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The Transient Buffer Exposure for the ABR call in the forward direction. This is the negotiated number of cells that the network would like to limit the source to sending during setup periods, before the first RM-cell returns." ::= { cwspAbrCallEntry 24 } cwspAbrCallFwdNrm OBJECT-TYPE SYNTAX INTEGER { nrm2(1), nrm4(2), nrm8(3), nrm16(4), nrm32(5), nrm64(6), nrm128(7), nrm256(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Maximum Number of Cells a source may send for each forward RM-cell in the forward direction for the ABR call. The default value is nrm32(5)." ::= { cwspAbrCallEntry 25 } cwspAbrCallFwdTrm OBJECT-TYPE SYNTAX INTEGER { trm0point78125(1), trm1point5625(2), trm3point125(3), trm6point25(4), trm12point5(5), trm25(6), trm50(7), trm100(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Upper Bound on the time between forward RM-cells in the forward direction for the ABR call." ::= { cwspAbrCallEntry 26 } cwspAbrCallFwdAdtf OBJECT-TYPE SYNTAX Integer32 (1..1023) MAX-ACCESS read-only STATUS current DESCRIPTION "The Allowed Cell Rate (ACR) Decrease Time Factor for the ABR call in the forward direction. This is the time permitted between sending RM-cells before the rate is decreased to ICR. Range is 10 ms to 10.23 seconds. The unit is 10 msecs. For example, the default value of 50 corresponds to a time factor of 500 ms. Larger values allow a source to retain its current rate longer, during periods of relative inactivity. The default is 50 (0.5 seconds)." ::= { cwspAbrCallEntry 27 } cwspAbrCallFwdCdf OBJECT-TYPE SYNTAX INTEGER { cdf0(1), cdfOneOver64(2), cdfOneOver32(3), cdfOneOver16(4), cdfOneOver8(5), cdfOneOver4(6), cdfOneOver2(7), cdfOne(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Cutoff Decrease Factor for the ABR call in the forward direction. This controls the decrease in Allowed Cell Rate (ACR) associated with missing RM-cell count (CRM). Larger values result in faster rate decrease. The default value is cdfOneOver16(4)." ::= { cwspAbrCallEntry 28 } cwspAbrCallFwdFrameDiscard OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Whether Frame Discard is enabled or disabled in the forward direction for the ABR call." ::= { cwspAbrCallEntry 29 } cwspAbrCallBwdPcr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The Peak Cell Rate for the ABR call in the backward direction." ::= { cwspAbrCallEntry 30 } cwspAbrCallBwdMcr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The Minimum Cell Rate for the ABR call in the backward direction." ::= { cwspAbrCallEntry 31 } cwspAbrCallBwdIcr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The Initial Cell Rate for the ABR call in the backward direction. This is the rate at which the source starts, both initially and after an idle period. The value must not be larger than PCR, and is usually lower." ::= { cwspAbrCallEntry 32 } cwspAbrCallBwdRif OBJECT-TYPE SYNTAX INTEGER { rifOneOver32768(1), rifOneOver16384(2), rifOneOver8192(3), rifOneOver4096(4), rifOneOver2048(5), rifOneOver1024(6), rifOneOver512(7), rifOneOver256(8), rifOneOver128(9), rifOneOver64(10), rifOneOver32(11), rifOneOver16(12), rifOneOver8(13), rifOneOver4(14), rifOneOver2(15), rifOne(16) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Rate Increase Factor for the ABR call in the backward direction. This controls the rate at which the rate increases, when a forward RM-cell is received with CI=0 and NI=0. Larger values lead to faster rate increase. The default value is rifOneOver16(12)." ::= { cwspAbrCallEntry 33 } cwspAbrCallBwdRdf OBJECT-TYPE SYNTAX INTEGER { rdfOneOver32768(1), rdfOneOver16384(2), rdfOneOver8192(3), rdfOneOver4096(4), rdfOneOver2048(5), rdfOneOver1024(6), rdfOneOver512(7), rdfOneOver256(8), rdfOneOver128(9), rdfOneOver64(10), rdfOneOver32(11), rdfOneOver16(12), rdfOneOver8(13), rdfOneOver4(14), rdfOneOver2(15), rdfOne(16) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Rate Decrease Factor for the ABR call in the backward direction. This controls the rate decrease which occurs when forward RM-cells with CI=1, are received. Larger values lead to faster rate decrease. The default value is rdfOneOver16(12)." ::= { cwspAbrCallEntry 34 } cwspAbrCallBwdTbe OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The Transient Buffer Exposure for the ABR call in the backward direction. This is the negotiated number of cells that the network would like to limit the source to sending during setup periods, before the first RM-cell returns." ::= { cwspAbrCallEntry 35 } cwspAbrCallBwdNrm OBJECT-TYPE SYNTAX INTEGER { nrm2(1), nrm4(2), nrm8(3), nrm16(4), nrm32(5), nrm64(6), nrm128(7), nrm256(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Maximum Number of Cells a source may send for each forward RM-cell in the backward direction for the ABR call. The default value is nrm32(5)." ::= { cwspAbrCallEntry 36 } cwspAbrCallBwdTrm OBJECT-TYPE SYNTAX INTEGER { trm0point78125(1), trm1point5625(2), trm3point125(3), trm6point25(4), trm12point5(5), trm25(6), trm50(7), trm100(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Upper Bound on the time between forward RM-cells in the backward direction for the ABR call." ::= { cwspAbrCallEntry 37 } cwspAbrCallBwdAdtf OBJECT-TYPE SYNTAX Integer32 (1..1023) MAX-ACCESS read-only STATUS current DESCRIPTION "The Allowed Cell Rate (ACR) Decrease Time Factor for the ABR call in the backward direction. This is the time permitted between sending RM-cells before the rate is decreased to ICR. Range is 10 ms to 10.23 seconds. The unit is 10 msecs. For example, the default value of 50 corresponds to a time factor of 500 ms. Larger values allow a source to retain its current rate longer, during periods of relative inactivity. The default is 50 (0.5 seconds)." ::= { cwspAbrCallEntry 38 } cwspAbrCallBwdCdf OBJECT-TYPE SYNTAX INTEGER { cdf0(1), cdfOneOver64(2), cdfOneOver32(3), cdfOneOver16(4), cdfOneOver8(5), cdfOneOver4(6), cdfOneOver2(7), cdfOne(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Cutoff Decrease Factor for the ABR call in the backward direction. This controls the decrease in Allowed Cell Rate (ACR) associated with missing RM-cell count (CRM). Larger values result in faster rate decrease. The default value is cdfOneOver16(4)." ::= { cwspAbrCallEntry 39 } cwspAbrCallBwdFrameDiscard OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Whether Frame Discard is enabled or disabled in the backward direction for the ABR call." ::= { cwspAbrCallEntry 40 } cwspAbrCallFrtt OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The Fixed Round-Trip Time for the ABR call. This is the sum of the fixed and propagation delays from the source to the furthest destination and back." ::= { cwspAbrCallEntry 41 } cwspAbrCallMaxCtd OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The Maximum Cell Transfer Delay for the ABR call on this interface." ::= { cwspAbrCallEntry 42 } cwspAbrCallMaxFwdCdv OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The Maximum Cell Delay Variation in the forward direction for the ABR call on this interface." ::= { cwspAbrCallEntry 43 } cwspAbrCallMaxFwdClr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The Maximum Cell Loss Ratio in the forward direction for the ABR call on this interface." ::= { cwspAbrCallEntry 44 } cwspAbrCallMaxBwdCdv OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The Maximum Cell Delay Variation in the backward direction for the ABR call on this interface." ::= { cwspAbrCallEntry 45 } cwspAbrCallMaxBwdClr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The Maximum Cell Loss Ratio in the backward direction for the ABR call on this interface." ::= { cwspAbrCallEntry 46 } -- the following cswpConnTrace group is used to trace SVC -- connection in the pnni network. The NMS can fire up the -- action providing that the connection is active. -- the port connection trace group cwspConnTraceAvail OBJECT-TYPE SYNTAX Integer32(1..100) MAX-ACCESS read-only STATUS current DESCRIPTION "This object tells the number of calls can be traced concurrently. Depending on the system resource, this object may vary sometime to time. NMS should query this object to ensure there is system resource available before creating a row in the cwspConnTraceCntlTable." ::= { cwspConnTrace 1 } cwspConnTraceNextIndex OBJECT-TYPE SYNTAX Integer32(1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "When creating a row in the cwspConnTraceCntlTable, NMS should query this object to obtain the index value to be used for row creation." ::= { cwspConnTrace 2 } -- the port connection trace control table cwspConnTraceCntlTable OBJECT-TYPE SYNTAX SEQUENCE OF CwspConnTraceCntlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This Table contains the objects which control the creation of connection trace for the existing SVC call. " ::= { cwspConnTrace 3 } cwspConnTraceCntlEntry OBJECT-TYPE SYNTAX CwspConnTraceCntlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object controls the connection trace creation. NMS needs to acquire the next index available to create a row. In addition, NMS needs to provide all read-create objects in the same pdu with RowStatus to be CreateAndGo." INDEX { cwspConnTraceIndex } ::= { cwspConnTraceCntlTable 1 } CwspConnTraceCntlEntry ::= SEQUENCE { cwspConnTraceIndex Integer32, cwspConnTraceifIndex InterfaceIndex, cwspConnTraceSrcVpi Integer32, cwspConnTraceSrcVci Integer32, cwspConnTraceType INTEGER, cwspConnTraceCallRef Integer32, cwspConnTraceLeafRef Integer32, cwspConnTraceDestVpi Integer32, cwspConnTraceDestVci Integer32, cwspConnTraceDestCallRef Integer32, cwspConnTraceResultStatus INTEGER, cwspConnTraceQueryStatus RowStatus } cwspConnTraceIndex OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index to a row of connection trace." ::= { cwspConnTraceCntlEntry 1 } cwspConnTraceifIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-create STATUS current DESCRIPTION "The 'ifIndex' indicates the port to a trace connection." ::= { cwspConnTraceCntlEntry 2 } cwspConnTraceSrcVpi OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-create STATUS current DESCRIPTION "This object shows the VPI value of the starting point on this interface." ::= { cwspConnTraceCntlEntry 3 } cwspConnTraceSrcVci OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "This object shows The VCI value of the starting point on this interface. The value should be in the range of 32-65535 (0=SPVP)." ::= { cwspConnTraceCntlEntry 4 } cwspConnTraceType OBJECT-TYPE SYNTAX INTEGER { p2p(1), p2mp(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this object to either p2p or p2mp to specify tracing a p2p or p2mp connection." ::= { cwspConnTraceCntlEntry 5 } cwspConnTraceCallRef OBJECT-TYPE SYNTAX Integer32(0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the Call Reference value of the call on this interface." ::= { cwspConnTraceCntlEntry 6 } cwspConnTraceLeafRef OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "This object shows the value of the Leaf Reference (EndPointReference) of the Call on this interface, this value is used to support p2mp call trace. For p2p call, this value should be set as 0 by NMS." ::= { cwspConnTraceCntlEntry 7 } cwspConnTraceDestVpi OBJECT-TYPE SYNTAX Integer32(0..4095) MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the endpoint VPI value of the call on this interface." ::= { cwspConnTraceCntlEntry 8 } cwspConnTraceDestVci OBJECT-TYPE SYNTAX Integer32(0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the endpoint VCI value of the call on this interface." ::= { cwspConnTraceCntlEntry 9 } cwspConnTraceDestCallRef OBJECT-TYPE SYNTAX Integer32(0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the endpoint call reference on this interface." ::= { cwspConnTraceCntlEntry 10 } cwspConnTraceResultStatus OBJECT-TYPE SYNTAX INTEGER { traceInProgress(1), traceCompleted(2), traceIncompleted(3), traceExceededLength(4), traceContRefused(5), traceLackResource(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the result of tracing the call. NMS should get positive result (i.e. traceCompleted) for this attribute before query the cwspConnTraceTable." ::= { cwspConnTraceCntlEntry 11 } cwspConnTraceQueryStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object used to manage rows in this table. However, only CreateAndGo, NotInService, Active, and Destroy are start up the trace. To remove a row, NMS set this value to Destroy. The managed device will either return Active or NotInService." ::= { cwspConnTraceCntlEntry 12 } -- the port connection data table cwspConnTraceTable OBJECT-TYPE SYNTAX SEQUENCE OF CwspConnTraceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the objects which show the traversed node information in the existing SVC call. " ::= { cwspConnTrace 4 } cwspConnTraceEntry OBJECT-TYPE SYNTAX CwspConnTraceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of the cwspConnTraceTable used to return information about all the nodes belongs to the connection which search criteria is corresponding to instance of the cwspConnTraceCntlTable. " INDEX { cwspConnTraceIndex, cwspConnTraceDataIndex } ::= { cwspConnTraceTable 1 } CwspConnTraceEntry ::= SEQUENCE { cwspConnTraceDataIndex Integer32, cwspConnTraceNodeId PnniNodeId, cwspConnTraceEgressPortId PnniPortId, cwspConnTraceEgressVpi Integer32, cwspConnTraceEgressVci Integer32, cwspConnTraceEgressCallRef Integer32, cwspConnTraceEgressPhyPortId OCTET STRING, cwspConnTraceLastNode TruthValue } cwspConnTraceDataIndex OBJECT-TYPE SYNTAX Integer32(1..100) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Along with cwspConnTraceIndex, this object specified an unique entry in the cwspConnTraceTable." ::= { cwspConnTraceEntry 1 } cwspConnTraceNodeId OBJECT-TYPE SYNTAX PnniNodeId MAX-ACCESS read-only STATUS current DESCRIPTION "This octet string represents 22 bytes nodeId in the traced connection." ::= { cwspConnTraceEntry 2 } cwspConnTraceEgressPortId OBJECT-TYPE SYNTAX PnniPortId MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents 4 bytes logical port ID of the traversed node. When 0 is specified, the destination node for the trace is reached." ::= { cwspConnTraceEntry 3 } cwspConnTraceEgressVpi OBJECT-TYPE SYNTAX Integer32(0..4095) MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the Egress port's VPI value for the traced connection." ::= { cwspConnTraceEntry 4 } cwspConnTraceEgressVci OBJECT-TYPE SYNTAX Integer32(0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the Egress port's VCI value for the traced connection" ::= { cwspConnTraceEntry 5 } cwspConnTraceEgressCallRef OBJECT-TYPE SYNTAX Integer32(0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the Egress port's call reference." ::= { cwspConnTraceEntry 6 } cwspConnTraceEgressPhyPortId OBJECT-TYPE SYNTAX OCTET STRING (SIZE(8)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the Egress port's physical port Identifier for the traversed node; if this object is 0 meaning that the destination node for the traced connection has been reached. the meaning for the bytes are: first byte -- flag (used by CLI to decode the rest of bytes ) 2nd byte -- shelf 3rd & 4th bytes -- slot 5th byte -- subslot 6th & 7th bytes -- port 8th byte -- subport " ::= { cwspConnTraceEntry 7 } cwspConnTraceLastNode OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This value indicates if this entry contains the information about the last node where this trace ends. If it is the last node, this value is 'true(1)' or it is 'false(2)'. " ::= { cwspConnTraceEntry 8 } -- the PNNI routing group -- This group is created for PNNI notifications (traps) to use ciscoWANPnniLinkStatus OBJECT-TYPE SYNTAX INTEGER { in2win(1), -- in 2-Way Inside state out2win(2), -- out of 2-Way Inside in2wout(3), -- in 2-Way Outside state out2wout(4), -- out of 2-Way Outside inCout(5), -- in Common Outside state outCout(6) } -- out of Common Outside MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the status of a link has changed: 1 - the link entered the 2-Way Inside state, 2 - the link exit the 2-Way Inside state, 3 - the link entered the 2-Way Outside state, 4 - the link exit the 2-Way Outside state. 5 - the link entered the Common Outside state, or 6 - the link exit the Common Outside state and entered the 1-Way Outside state." ::= { ciscoWANPnniRouting 1 } ciscoWANPnniPglStatus OBJECT-TYPE SYNTAX INTEGER { ok(1), hung(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the status of PGL process has changed: 1 - the PGL exit the hung-election state, or 2 - the PGL entered the hung-election state." ::= { ciscoWANPnniRouting 2 } ciscoWANPnniReachability OBJECT-TYPE SYNTAX INTEGER { ok(1), fail(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object is used in conjunction with ciscoWANPnniRemoteNodeId to indicate the reachability of the RemoteNode has changed: 1 - RemoteNode became reachable, or 2 - RemoteNode became unreachable." ::= { ciscoWANPnniRouting 3 } ciscoWANPnniRemoteNodeId OBJECT-TYPE SYNTAX PnniNodeId MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the node identifier of a remote node. If the remote node ID is unknown, this attribute is set to all zeros." ::= { ciscoWANPnniRouting 4 } ciscoWANPnniPortId OBJECT-TYPE SYNTAX PnniPortId MAX-ACCESS read-only STATUS current DESCRIPTION "The port identifier of the port." ::= { ciscoWANPnniRouting 5 } -- the interface operation table cwspOperationTable OBJECT-TYPE SYNTAX SEQUENCE OF CwspOperationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Interface operation table contains the runtime negotiated values between platform, PNNI controller and peer on an interface" ::= { cwspOperation 1 } cwspOperationEntry OBJECT-TYPE SYNTAX CwspOperationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the interface operation table containing negotiated values of an interface" INDEX { ifIndex } ::= { cwspOperationTable 1 } CwspOperationEntry ::= SEQUENCE { cwspOperIlmiEnable TruthValue, cwspOperIfcType INTEGER, cwspOperIfcSide INTEGER, cwspOperMaxVPCs Integer32, cwspOperMaxVCCs Integer32, cwspOperMaxVpiBits Integer32, cwspOperMaxVciBits Integer32, cwspOperUniType INTEGER, cwspOperUniVersion INTEGER, cwspOperDeviceType INTEGER, cwspOperIlmiVersion INTEGER, cwspOperNniSigVersion INTEGER, cwspOperMaxSvpcVpi Integer32, cwspOperMinSvpcVpi Integer32, cwspOperMaxSvccVpi Integer32, cwspOperMinSvccVpi Integer32, cwspOperMaxSvccVci Integer32, cwspOperMinSvccVci Integer32, cwspOperAddrPlanSupported INTEGER } cwspOperIlmiEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The operational state of ILMI." ::= { cwspOperationEntry 1 } cwspOperIfcType OBJECT-TYPE SYNTAX INTEGER { publicUni(1), privateUni(2), iisp(3), pnni(4), aini(5), enni(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The interface type of an interface publicUni -- Public User-Network Interface privateUni -- Private User-Network Interface iisp -- Interim Inter-Switch Signaling Protocol pnni -- Private Network-Network Interface aini -- ATM Inter-Network Interface enni -- Enhanced Network-Network Interface, a cisco proprietary interfac type." ::= { cwspOperationEntry 2 } cwspOperIfcSide OBJECT-TYPE SYNTAX INTEGER { userSide(1), networkSide(2), symmetric(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The IME type of the ATM device which is concluded from automatic interface type determination procedure." REFERENCE "ATM Forum ILMI 4.0 Section 8.3.4.1" ::= { cwspOperationEntry 3 } cwspOperMaxVPCs OBJECT-TYPE SYNTAX Integer32(0..4096) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of switched and permanent VPCs supported on this ATM interface" ::= { cwspOperationEntry 4 } cwspOperMaxVCCs OBJECT-TYPE SYNTAX Integer32(0..65536) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of switched and permanent VCCs supported on this ATM interface" ::= { cwspOperationEntry 5 } cwspOperMaxVpiBits OBJECT-TYPE SYNTAX Integer32(0..12) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of active VPI bits on this ATM interface." ::= { cwspOperationEntry 6 } cwspOperMaxVciBits OBJECT-TYPE SYNTAX Integer32(0..16) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of active VCI bits on this ATM interface." ::= { cwspOperationEntry 7 } cwspOperUniType OBJECT-TYPE SYNTAX INTEGER { public(1), private(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the ATM device, either public or private." ::= { cwspOperationEntry 8 } cwspOperUniVersion OBJECT-TYPE SYNTAX INTEGER { version2point0(1), version3poing0(2), version3poing1(3), version4poing0(4), unsupported(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "An indication of the latest version of the ATM Forum UNI Signaling Specification that is supported on this ATM Interface. If this value is not present, a version of the UNI earlier than 3.1 is supported. If the peer IME's value of this object is the same as, or later than the local IME's value, then the version corresponding to the local IME's value should be attempted. Otherwise, if the peer IME's value of this object is earlier, and supported locally, then the local IME should attempt the version corresponding to the peer IME's value. Otherwise, compatibility of the two IMEs cannot be assumed." ::= { cwspOperationEntry 9 } cwspOperDeviceType OBJECT-TYPE SYNTAX INTEGER { user(1), node(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object determines the type of the ATM device. This object is used in automatic ATM Interface-Type determination procedure such that a correct operational ATM Interface-type can be determined. An ATM End System shall take the value of user(1), and an ATM network node shall take the value of node(2)." ::= { cwspOperationEntry 10 } cwspOperIlmiVersion OBJECT-TYPE SYNTAX INTEGER { unsupported(1), version4point0(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "An indication of the latest version of the ATM Forum ILMI Specification that is supported on this ATM Interface. If the peer IME's value of this object is the same as, or later than the local IME's value, then the version corresponding to the local IME's value should be attempted. Otherwise, if the peer IME's value of this object is earlier, and supported locally, then the local IME should attempt the version corresponding to the peer IME's value. Otherwise, compatibility of the two IMEs cannot be assumed. If this object is not present, a version of the ILMI earlier than 4.0 is supported." ::= { cwspOperationEntry 11 } cwspOperNniSigVersion OBJECT-TYPE SYNTAX INTEGER { unsupported(1), iisp(2), pnniVersion1point0(3), enni(4), aini(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "An indication of the latest version of the ATM Forum PNNI Signaling Specification that is supported on this ATM Interface. Note that the PNNI routing version is not determined through ILMI. If the peer IME's value of this object is the same as, or later than the local IME's value, then the version corresponding to the local IME's value should be attempted. Otherwise, if the peer IME's value of this object is earlier, and supported locally, then the local IME should attempt the version corresponding to the peer IME's value. Otherwise, compatibility of the two IMEs cannot be assumed. Note that 'enni' is not a signaling protocol." ::= { cwspOperationEntry 12 } cwspOperMaxSvpcVpi OBJECT-TYPE SYNTAX Integer32(1..4095) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum switched VPC VPI." ::= { cwspOperationEntry 13 } cwspOperMinSvpcVpi OBJECT-TYPE SYNTAX Integer32(1..4095) MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum switched VPC VPI." ::= { cwspOperationEntry 14 } cwspOperMaxSvccVpi OBJECT-TYPE SYNTAX Integer32(0..4095) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum switched VCC VPI." ::= { cwspOperationEntry 15 } cwspOperMinSvccVpi OBJECT-TYPE SYNTAX Integer32(0..4095) MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum switched VCC VPI." ::= { cwspOperationEntry 16 } cwspOperMaxSvccVci OBJECT-TYPE SYNTAX Integer32(35..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum switched VCC VCI." ::= { cwspOperationEntry 17 } cwspOperMinSvccVci OBJECT-TYPE SYNTAX Integer32(0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum switched VCC VCI." ::= { cwspOperationEntry 18 } cwspOperAddrPlanSupported OBJECT-TYPE SYNTAX INTEGER { both(1), aesa(2), e164(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The ATM address plan supported on a public UNI. For all other interfaces, the value is aesa." ::= { cwspOperationEntry 19 } -- cwspOperFailReason is used in Notifications cwspOperFailReason OBJECT-TYPE SYNTAX INTEGER { ilmiDown(1), portDown(2), vsiOperDown(3), vccfailure(4), neighIpChanged(5), vsiRemove(6), vsiAdminDown(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "Defined SVC port failures. Note: this object is used as trap varbind only. The NMS applications should not issue SNMP get, get-next for this object." ::= { cwspOperation 2 } ciscoWANSpvcFailReason OBJECT-TYPE SYNTAX CwspSpvcState MAX-ACCESS read-only STATUS current DESCRIPTION "Defines SPVC manager failures. Refer description in the textual convention. Note: this object is for Supporting Varbinds used only in trap definitions. The NMS applications should not depend on the implementation of this object. The SNMP Requests(GET,GET-NEXT) is not valid for this object." ::= { ciscoWANSpvc 1 } -- scalar object for spvc. cwspSpvcNodePrefix OBJECT-TYPE SYNTAX OCTET STRING(SIZE(13)) MAX-ACCESS read-write STATUS current DESCRIPTION "Spvc node prefix for the pnni controller. This node prefix identifies an SPVC node in the network." ::= { ciscoWANSpvc 2 } -- Conformance ciscoWANSvcMIBConformance OBJECT IDENTIFIER ::= { ciscoWANSvcMIB 3 } ciscoWANSvcMIBCompliances OBJECT IDENTIFIER ::= { ciscoWANSvcMIBConformance 1 } ciscoWANSvcMIBGroups OBJECT IDENTIFIER ::= { ciscoWANSvcMIBConformance 2 } -- Compliance ciscoWANSvcMIBCompliance MODULE-COMPLIANCE STATUS deprecated -- replaced by ciscoWANSvcMIBCompliance2 DESCRIPTION "The compliance statement for entities that support the Cisco SVC MIB. " MODULE -- compliance to this module MANDATORY-GROUPS { cwsInfoGrp, cwspConfigGrp, cwspCacConfigGrp, cwspCallStatsGrp, cwspSigStatsGrp, cwspCallGrp, cwspAbrCallGrp, cwspPrefixGrp, cwspLoadGrp, cwspAddressGrp, cwspConnTraceGrp, cwspOperationGrp } GROUP cwspSigConfigGrp DESCRIPTION "The signaling config group is optional." GROUP cwspSscopConfigGrp DESCRIPTION "The sscop config group is optional." GROUP cwspSscopStatsGrp DESCRIPTION "The sscop stat group is optional." GROUP cwspRegAddressGrp DESCRIPTION "The registered atm address group is optional." GROUP cwspRoutingGrp DESCRIPTION "The PNNI routing group is optional." GROUP cwspSpvcGrp DESCRIPTION "The Spvc group is optional." OBJECT cwspSpvcNodePrefix MIN-ACCESS read-only DESCRIPTION "Write Access is not permitted now until future release." OBJECT cwspMaxP2pCalls MIN-ACCESS read-only DESCRIPTION "Write Access is not permitted now until future release." ::= { ciscoWANSvcMIBCompliances 1 } ciscoWANSvcMIBCompliance2 MODULE-COMPLIANCE STATUS deprecated -- replaced by ciscoWANSvcMIBCompliance3 DESCRIPTION "The compliance statement for entities that support the Cisco SVC MIB. " MODULE -- compliance to this module MANDATORY-GROUPS { cwsInfoGrp, cwspConfigGrp, cwspCacConfigGrp, cwspCallStatsGrp, cwspSigStatsGrp, cwspCallGrp, cwspAbrCallGrp, cwspPrefixGrp, cwspLoadGrp, cwspAddressGrp, cwspConnTraceGrp2, cwspOperationGrp } GROUP cwspSigConfigGrp DESCRIPTION "The signaling config group is optional." GROUP cwspSscopConfigGrp DESCRIPTION "The sscop config group is optional." GROUP cwspSscopStatsGrp DESCRIPTION "The sscop stat group is optional." GROUP cwspRegAddressGrp DESCRIPTION "The registered atm address group is optional." GROUP cwspRoutingGrp DESCRIPTION "The PNNI routing group is optional." GROUP cwspSpvcGrp DESCRIPTION "The Spvc group is optional." OBJECT cwspSpvcNodePrefix MIN-ACCESS read-only DESCRIPTION "Write Access is not permitted now until future release." OBJECT cwspMaxP2pCalls MIN-ACCESS read-only DESCRIPTION "Write Access is not permitted now until future release." ::= { ciscoWANSvcMIBCompliances 2 } ciscoWANSvcMIBCompliance3 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities that support the Cisco SVC MIB. " MODULE -- compliance to this module MANDATORY-GROUPS { cwsInfoGrp, cwspConfigGrp3, cwspCacConfigGrp, cwspCallStatsGrp, cwspSigStatsGrp, cwspCallGrp, cwspAbrCallGrp, cwspPrefixGrp, cwspLoadGrp, cwspAddressGrp, cwspConnTraceGrp2, cwspOperationGrp } GROUP cwspSigConfigGrp DESCRIPTION "The signaling config group is optional." GROUP cwspSscopConfigGrp DESCRIPTION "The sscop config group is optional." GROUP cwspSscopStatsGrp DESCRIPTION "The sscop stat group is optional." GROUP cwspRegAddressGrp DESCRIPTION "The registered atm address group is optional." GROUP cwspRoutingGrp DESCRIPTION "The PNNI routing group is optional." GROUP cwspSpvcGrp DESCRIPTION "The Spvc group is optional." OBJECT cwspSpvcNodePrefix MIN-ACCESS read-only DESCRIPTION "Write Access is not permitted now until future release" OBJECT cwspMaxP2pCalls MIN-ACCESS read-only DESCRIPTION "Write Access is not permitted now until future release" ::= { ciscoWANSvcMIBCompliances 3 } -- Units of Conformance cwsInfoGrp OBJECT-GROUP OBJECTS { cwsSwRevision, cwsControllerStatus, cwspPnniStndbyControllerStatus, cwspPnniControllerStatus, cwspPnniControllerPhySlot } STATUS current DESCRIPTION "A collection of objects providing device level information." ::= { ciscoWANSvcMIBGroups 1 } cwspConfigGrp OBJECT-GROUP OBJECTS { cwspAdminStatus, cwspOperStatus, cwspSvcBlocked, cwspSpvcBlocked, cwspIlmiAddrRegEnable, cwspIlmiAutoConfEnable, cwspIlmiServRegEnable, cwspPhyIdentifier, cwspSignallingVpi, cwspSignallingVci, cwspRoutingVpi, cwspRoutingVci, cwspMaxVpiBits, cwspMaxVciBits, cwspUniVersion, cwspNniVersion, cwspUniType, cwspSide, cwspMaxP2pCalls, cwspMaxP2mpRoots, cwspMaxP2mpLeafs, cwspMinSvccVpi, cwspMaxSvccVpi, cwspMinSvccVci, cwspMaxSvccVci, cwspMinSvpcVpi, cwspMaxSvpcVpi, cwspEnhancedIisp, cwspConfigTableRowStatus, cwspAddrPlanSupported } STATUS deprecated -- replace by cwspConfigGrp2 DESCRIPTION "A collection of objects providing information about the controller interface operation and associated parameters." ::= { ciscoWANSvcMIBGroups 2 } cwspCacConfigGrp OBJECT-GROUP OBJECTS { cwspUtilFactorCbr, cwspUtilFactorRtVbr, cwspUtilFactorNrtVbr, cwspUtilFactorAbr, cwspUtilFactorUbr, cwspMaxBwCbr, cwspMaxBwRtVbr, cwspMaxBwNrtVbr, cwspMaxBwAbr, cwspMaxBwUbr, cwspMinBwCbr, cwspMinBwRtVbr, cwspMinBwNrtVbr, cwspMinBwAbr, cwspMinBwUbr, cwspMaxVcCbr, cwspMaxVcRtVbr, cwspMaxVcNrtVbr, cwspMaxVcAbr, cwspMaxVcUbr, cwspMinVcCbr, cwspMinVcRtVbr, cwspMinVcNrtVbr, cwspMinVcAbr, cwspMinVcUbr, cwspMaxVcBwCbr, cwspMaxVcBwRtVbr, cwspMaxVcBwNrtVbr, cwspMaxVcBwAbr, cwspMaxVcBwUbr, cwspDefaultCdvtCbr, cwspDefaultCdvtRtVbr, cwspDefaultCdvtNrtVbr, cwspDefaultCdvtAbr, cwspDefaultCdvtUbr, cwspDefaultMbsRtVbr, cwspDefaultMbsNrtVbr } STATUS current DESCRIPTION "A collection of objects providing information about CAC information of a interface." ::= { ciscoWANSvcMIBGroups 3 } cwspCallStatsGrp OBJECT-GROUP OBJECTS { cwspCountReset, cwspInCallAttempts, cwspInCallEstabs, cwspInCallFailures, cwspInFilterFailures, cwspInRouteFailures, cwspInResrcFailures, cwspInTimerFailures, cwspInCrankbacks, cwspOutCallAttempts, cwspOutCallEstabs, cwspOutCallFailures, cwspOutFilterFailures, cwspOutRouteFailures, cwspOutResrcFailures, cwspOutTimerFailures, cwspOutCrankbacks } STATUS current DESCRIPTION "A collection of objects providing information about call statistics of a interface." ::= { ciscoWANSvcMIBGroups 4 } cwspSigStatsGrp OBJECT-GROUP OBJECTS { cwspSigCounterReset, cwspCallProcRcv, cwspConnectRcv, cwspConnectAckRcv, cwspSetupRcv, cwspReleaseRcv, cwspReleaseComplRcv, cwspRestartRcv, cwspRestartAckRcv, cwspStatusRcv, cwspStatusEnqRcv, cwspNotifyRcv, cwspAlertRcv, cwspProgressRcv, cwspAddPtyRcv, cwspAddPtyAckRcv, cwspAddPtyRejRcv, cwspDropPtyRcv, cwspIncorrectMsgRcv, cwspTimerExpiries, cwspLastCause, cwspLastDiagnostic, cwspCallProcXmt, cwspConnectXmt, cwspConnectAckXmt, cwspSetupXmt, cwspReleaseXmt, cwspReleaseComplXmt, cwspRestartXmt, cwspRestartAckXmt, cwspStatusXmt, cwspStatusEnqXmt, cwspNotifyXmt, cwspAlertXmt, cwspProgressXmt, cwspAddPtyXmt, cwspAddPtyAckXmt, cwspAddPtyRejXmt, cwspDropPtyXmt, cwspSscopStatus } STATUS current DESCRIPTION "A collection of objects providing information about signaling statistics." ::= { ciscoWANSvcMIBGroups 5 } cwspCallGrp OBJECT-GROUP OBJECTS { cwspCallCallRef, cwspCallCallingAddress, cwspCallCalledAddress, cwspCallCallingSubAddr, cwspCallCalledSubAddr, cwspCallOtherIntfIndex, cwspCallOtherIntfVpi, cwspCallOtherIntfVci, cwspCallOtherIntfCallRef, cwspCallType, cwspCallStartTime, cwspCallBearerClass, cwspCallServiceCategory, cwspCallCastType, cwspCallClipSusceptibility, cwspCallFwdConformance, cwspCallFwdPcr, cwspCallFwdScr, cwspCallFwdMbs, cwspCallFwdCdvt, cwspCallFwdFrameDiscard, cwspCallBwdConformance, cwspCallBwdPcr, cwspCallBwdScr, cwspCallBwdMbs, cwspCallBwdCdvt, cwspCallBwdFrameDiscard, cwspCallMaxCtd, cwspCallMaxFwdCdv, cwspCallMaxFwdClr, cwspCallMaxBwdCdv, cwspCallMaxBwdClr } STATUS current DESCRIPTION "A collection of objects providing information about the p2p or p2mp SVC/SPVC calls and associated parameters." ::= { ciscoWANSvcMIBGroups 6 } cwspAbrCallGrp OBJECT-GROUP OBJECTS { cwspAbrCallCallRef, cwspAbrCallClgAddress, cwspAbrCallCldAddress, cwspAbrCallClgSubAddr, cwspAbrCallCldSubAddr, cwspAbrCallOtherIntfIndex, cwspAbrCallOtherIntfVpi, cwspAbrCallOtherIntfVci, cwspAbrCallOtherIntfCallRef, cwspAbrCallType, cwspAbrCallStartTime, cwspAbrCallBearerClass, cwspAbrCallServiceCategory, cwspAbrCallCastType, cwspAbrCallClipSusceptibility, cwspAbrCallFwdConformance, cwspAbrCallFwdPcr, cwspAbrCallFwdMcr, cwspAbrCallFwdIcr, cwspAbrCallFwdRif, cwspAbrCallFwdRdf, cwspAbrCallFwdTbe, cwspAbrCallFwdNrm, cwspAbrCallFwdTrm, cwspAbrCallFwdAdtf, cwspAbrCallFwdCdf, cwspAbrCallFwdFrameDiscard, cwspAbrCallBwdPcr, cwspAbrCallBwdMcr, cwspAbrCallBwdIcr, cwspAbrCallBwdRif, cwspAbrCallBwdRdf, cwspAbrCallBwdTbe, cwspAbrCallBwdNrm, cwspAbrCallBwdTrm, cwspAbrCallBwdAdtf, cwspAbrCallBwdCdf, cwspAbrCallBwdFrameDiscard, cwspAbrCallFrtt, cwspAbrCallMaxCtd, cwspAbrCallMaxFwdCdv, cwspAbrCallMaxFwdClr, cwspAbrCallMaxBwdCdv, cwspAbrCallMaxBwdClr } STATUS current DESCRIPTION "A collection of objects providing information about ABR calls and associated parameters of a interface." ::= { ciscoWANSvcMIBGroups 7 } cwspPrefixGrp OBJECT-GROUP OBJECTS { cwspPrefixRowStatus } STATUS current DESCRIPTION "A table specifying the network prefix(es) used for ILMI address registration." ::= { ciscoWANSvcMIBGroups 8 } cwspLoadGrp OBJECT-GROUP OBJECTS { cwspLoadBwTotal, cwspLoadMaxBwCbr, cwspLoadMaxBwRtVbr, cwspLoadMaxBwNrtVbr, cwspLoadMaxBwAbr, cwspLoadMaxBwUbr, cwspLoadBwAvail, cwspLoadAvlBwCbr, cwspLoadAvlBwRtVbr, cwspLoadAvlBwNrtVbr, cwspLoadAvlBwAbr, cwspLoadAvlBwUbr, cwspLoadVcAvail, cwspLoadAvlVcCbr, cwspLoadAvlVcRtVbr, cwspLoadAvlVcNrtVbr, cwspLoadAvlVcAbr, cwspLoadAvlVcUbr, cwspLoadCtdCbr, cwspLoadCtdRtVbr, cwspLoadCtdNrtVbr, cwspLoadCtdAbr, cwspLoadCtdUbr, cwspLoadCdvCbr, cwspLoadCdvRtVbr, cwspLoadCdvNrtVbr, cwspLoadCdvAbr, cwspLoadCdvUbr, cwspLoadClr0Cbr, cwspLoadClr0RtVbr, cwspLoadClr0NrtVbr, cwspLoadClr0Abr, cwspLoadClr0Ubr, cwspLoadClr01Cbr, cwspLoadClr01RtVbr, cwspLoadClr01NrtVbr, cwspLoadClr01Abr, cwspLoadClr01Ubr, cwspLoadMinGurCrCbr, cwspLoadMinGurCrRtVbr, cwspLoadMinGurCrNrtVbr, cwspLoadMinGurCrAbr, cwspLoadMinGurCrUbr } STATUS current DESCRIPTION "A collection of objects providing information about load information and associated parameters of a interface." ::= { ciscoWANSvcMIBGroups 9 } cwspAddressGrp OBJECT-GROUP OBJECTS { cwspAddrType, cwspAddrProto, cwspAddrPlan, cwspAddrScope, cwspAddrRedistribute, cwspAddressRowStatus } STATUS current DESCRIPTION "A collection of objects providing information about ATM End System Addresses." ::= { ciscoWANSvcMIBGroups 10 } cwspSigConfigGrp OBJECT-GROUP OBJECTS { cwspSigCfgT301, cwspSigCfgT303, cwspSigCfgT308, cwspSigCfgT310, cwspSigCfgT316, cwspSigCfgT317, cwspSigCfgT322, cwspSigCfgT397, cwspSigCfgT398, cwspSigCfgT399 } STATUS current DESCRIPTION "A collection of objects providing information about signaling configuration and associated parameters." ::= { ciscoWANSvcMIBGroups 11 } cwspSscopConfigGrp OBJECT-GROUP OBJECTS { cwspSscopTmrCC, cwspSscopTmrKeepAlive, cwspSscopTmrNoResp, cwspSscopTmrPoll, cwspSscopTmtIdle, cwspSscopMaxCC, cwspSscopMaxPD, cwspSscopMaxSTAT } STATUS current DESCRIPTION "A collection of objects providing information about SSCOP configuration and associated parameters." ::= { ciscoWANSvcMIBGroups 12 } cwspSscopStatsGrp OBJECT-GROUP OBJECTS { cwspSscopCounterReset, cwspSscopIgnoredPduRcv, cwspSscopBgnRcv, cwspSscopBgakRcv, cwspSscopEndRcv, cwspSscopEndakRcv, cwspSscopRsRcv, cwspSscopRsakRcv, cwspSscopBgrejRcv, cwspSscopSdRcv, cwspSscopSdpRcv, cwspSscopPollRcv, cwspSscopStatRcv, cwspSscopUstatRcv, cwspSscopUdRcv, cwspSscopMdRcv, cwspSscopErakRcv, cwspSscopBgnXmt, cwspSscopBgakXmt, cwspSscopEndXmt, cwspSscopEndakXmt, cwspSscopRsXmt, cwspSscopRsakXmt, cwspSscopBgrejXmt, cwspSscopSdXmt, cwspSscopSdpXmt, cwspSscopPollXmt, cwspSscopStatXmt, cwspSscopUstatXmt, cwspSscopUdXmt, cwspSscopMdXmt, cwspSscopErakXmt } STATUS current DESCRIPTION "A collection of objects providing information about SSCOP statistics." ::= { ciscoWANSvcMIBGroups 13 } cwspRegAddressGrp OBJECT-GROUP OBJECTS { cwspRegAtmAddress, cwspRegAddressOrgSscope } STATUS current DESCRIPTION "A collection of objects providing information about registed ATM address." ::= { ciscoWANSvcMIBGroups 14 } cwspRoutingGrp OBJECT-GROUP OBJECTS { ciscoWANPnniLinkStatus, ciscoWANPnniPglStatus, ciscoWANPnniReachability, ciscoWANPnniRemoteNodeId, ciscoWANPnniPortId } STATUS current DESCRIPTION "A collection of objects providing information about PNNI topology." ::= { ciscoWANSvcMIBGroups 15 } cwspConnTraceGrp OBJECT-GROUP OBJECTS { cwspConnTraceAvail, cwspConnTraceNextIndex, cwspConnTraceifIndex, cwspConnTraceSrcVpi, cwspConnTraceSrcVci, cwspConnTraceType, cwspConnTraceCallRef, cwspConnTraceLeafRef, cwspConnTraceDestVpi, cwspConnTraceDestVci, cwspConnTraceDestCallRef, cwspConnTraceResultStatus, cwspConnTraceQueryStatus, cwspConnTraceNodeId, cwspConnTraceEgressPortId, cwspConnTraceEgressVpi, cwspConnTraceEgressVci, cwspConnTraceEgressCallRef, cwspConnTraceEgressPhyPortId } STATUS deprecated -- replaced by cwspConnTraceGrp2 DESCRIPTION "A collection of objects providing trace information about SVC/PNNI connnection." ::= { ciscoWANSvcMIBGroups 16 } cwspOperationGrp OBJECT-GROUP OBJECTS { cwspOperIlmiEnable, cwspOperIfcType, cwspOperIfcSide, cwspOperMaxVPCs, cwspOperMaxVCCs, cwspOperMaxVpiBits, cwspOperMaxVciBits, cwspOperUniType, cwspOperUniVersion, cwspOperDeviceType, cwspOperIlmiVersion, cwspOperNniSigVersion, cwspOperMaxSvpcVpi, cwspOperMinSvpcVpi, cwspOperMaxSvccVpi, cwspOperMinSvccVpi, cwspOperMaxSvccVci, cwspOperMinSvccVci, cwspOperFailReason, cwspOperAddrPlanSupported, cwspIlmiSecureLink, cwspIlmiAttachmentPoint, cwspIlmiLocalAttrStd, cwspIlmiUCSMEnable } STATUS current DESCRIPTION "A collection of objects providing information about runtime negotiated values between platform, PNNI controller and peer on an interface." ::= { ciscoWANSvcMIBGroups 17 } cwspSpvcGrp OBJECT-GROUP OBJECTS { ciscoWANSpvcFailReason, cwspSpvcNodePrefix } STATUS current DESCRIPTION "A collection of objects providing spvc related information in pnni controller." ::= { ciscoWANSvcMIBGroups 18 } cwspConnTraceGrp2 OBJECT-GROUP OBJECTS { cwspConnTraceAvail, cwspConnTraceNextIndex, cwspConnTraceifIndex, cwspConnTraceSrcVpi, cwspConnTraceSrcVci, cwspConnTraceType, cwspConnTraceCallRef, cwspConnTraceLeafRef, cwspConnTraceDestVpi, cwspConnTraceDestVci, cwspConnTraceDestCallRef, cwspConnTraceResultStatus, cwspConnTraceQueryStatus, cwspConnTraceNodeId, cwspConnTraceEgressPortId, cwspConnTraceEgressVpi, cwspConnTraceEgressVci, cwspConnTraceEgressCallRef, cwspConnTraceEgressPhyPortId, cwspConnTraceLastNode } STATUS current DESCRIPTION "A collection of objects providing trace information about SVC/PNNI connnection." ::= { ciscoWANSvcMIBGroups 19 } cwspConfigGrp2 OBJECT-GROUP OBJECTS { cwspAdminStatus, cwspOperStatus, cwspSvcBlocked, cwspSpvcBlocked, cwspIlmiAddrRegEnable, cwspIlmiAutoConfEnable, cwspIlmiServRegEnable, cwspPhyIdentifier, cwspSignallingVpi, cwspSignallingVci, cwspRoutingVpi, cwspRoutingVci, cwspMaxVpiBits, cwspMaxVciBits, cwspUniVersion, cwspNniVersion, cwspUniType, cwspSide, cwspMaxP2pCalls, cwspMaxP2mpRoots, cwspMaxP2mpLeafs, cwspMinSvccVpi, cwspMaxSvccVpi, cwspMinSvccVci, cwspMaxSvccVci, cwspMinSvpcVpi, cwspMaxSvpcVpi, cwspEnhancedIisp, cwspConfigTableRowStatus, cwspAddrPlanSupported, cwspIlmiSecureLink, cwspIlmiAttachmentPoint, cwspIlmiLocalAttrStd, cwspIlmiUCSMEnable, cwspRoutingPriority } STATUS deprecated -- replaced by cwspConfigGrp3 DESCRIPTION "A collection of objects providing information about the controller interface operation and associated parameters." ::= { ciscoWANSvcMIBGroups 20 } cwspConfigGrp3 OBJECT-GROUP OBJECTS { cwspAdminStatus, cwspOperStatus, cwspSvcBlocked, cwspSpvcBlocked, cwspIlmiAddrRegEnable, cwspIlmiAutoConfEnable, cwspIlmiServRegEnable, cwspPhyIdentifier, cwspSignallingVpi, cwspSignallingVci, cwspRoutingVpi, cwspRoutingVci, cwspMaxVpiBits, cwspMaxVciBits, cwspUniVersion, cwspNniVersion, cwspUniType, cwspSide, cwspMaxP2pCalls, cwspMaxP2mpRoots, cwspMaxP2mpLeafs, cwspMinSvccVpi, cwspMaxSvccVpi, cwspMinSvccVci, cwspMaxSvccVci, cwspMinSvpcVpi, cwspMaxSvpcVpi, cwspEnhancedIisp, cwspConfigTableRowStatus, cwspAddrPlanSupported, cwspIlmiSecureLink, cwspIlmiAttachmentPoint, cwspIlmiLocalAttrStd, cwspIlmiUCSMEnable, cwspRoutingPriority, cwspSpvcAddress } STATUS current DESCRIPTION "A collection of objects providing information about the controller interface operation and associated parameters." ::= { ciscoWANSvcMIBGroups 21 } END