-- ***************************************************************** -- SRM-MIB : MIB For SRM(Service Resource Module) in MGX82xx -- series products. -- -- August 2002, Subra Hegde -- -- Copyright (c) 2002 by cisco Systems, Inc. -- All rights reserved. -- ***************************************************************** CISCO-WAN-SRM-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF cardSpecific FROM BASIS-MIB ciscoWan FROM CISCOWAN-SMI; ciscoWanSrmMIB MODULE-IDENTITY LAST-UPDATED "200208260000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-wanatm@cisco.com" DESCRIPTION "The MIB module for configuration of bulk distribution (de-multiplexing of traffic from higher-bandwidth to lower-bandwidth interfaces). This is used for configuring bulk distribution of T3 interfaces on T1 modules supported in MGX82xx series. Some of the T1 modules are AUSM, FRSM,CESM. This MIB module also contains info. on configuring bulk distribution of SONET interfaces(VT interfaces) on T1 Modules. SRM - Service Resource Module SRME - Service Resource Module Enhanced." REVISION "200208260000Z" DESCRIPTION "Initial version of the MIB. The content of this MIB was originally available in CISCO-WAN-AXIPOP-MIB defined using SMIv1. The applicable objects from CISCO-WAN-AXIPOP-MIB are defined using SMIv2 in this MIB. Also the descriptions of some of the objects have been modified." ::= { ciscoWan 30 } srm3T3CnfGrp OBJECT IDENTIFIER ::= {cardSpecific 10} srmeCnfGrp OBJECT IDENTIFIER ::= {cardSpecific 22} -- ******************************************************************* -- -- srm3T3CnfGrpTable: -- This table contains DS1 mapping configuration for SRM-3T3 card. -- This group is card specific for SRM-3T3 card. -- -- ******************************************************************* srm3T3CnfGrpTable OBJECT-TYPE SYNTAX SEQUENCE OF Srm3T3CnfGrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SRM 3T3 configuration table, it is the distribution of a T3 line. " ::= { srm3T3CnfGrp 1 } srm3T3CnfGrpEntry OBJECT-TYPE SYNTAX Srm3T3CnfGrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "an entry in the T3 configuration table " INDEX { srmT3LineNum, srmStartT1LineNum } ::= { srm3T3CnfGrpTable 1 } Srm3T3CnfGrpEntry ::= SEQUENCE { srmT3LineNum Integer32, srmStartT1LineNum Integer32, srmT1RowStatus INTEGER, srmTargetSlotNum Integer32, srmTargetSlotLineNum Integer32 } srmT3LineNum OBJECT-TYPE SYNTAX Integer32 (1..3) MAX-ACCESS read-only STATUS current DESCRIPTION "Select T3 line number. There is no default value for this object." ::= { srm3T3CnfGrpEntry 1 } srmStartT1LineNum OBJECT-TYPE SYNTAX Integer32 (1..28) MAX-ACCESS read-only STATUS current DESCRIPTION "The start T1 number to be affected. There is no default value for this object." ::= { srm3T3CnfGrpEntry 2 } srmT1RowStatus OBJECT-TYPE SYNTAX INTEGER { add (1), delete (2), modify (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "a command is used to add, delete, or modify one or more DS1 mapping. Default value is delete." ::= { srm3T3CnfGrpEntry 3 } srmTargetSlotNum OBJECT-TYPE SYNTAX Integer32 (1..32) MAX-ACCESS read-write STATUS current DESCRIPTION " specify the target slot number to be linked. There is no default value for this object. For MGX8850: SRM01 services slots 1 - 6 and 9 - 14, SRM02 services slots 17 - 22 and 25 - 30 For MGX8220: SYNTAX Integer32 (5 ..14) " ::= { srm3T3CnfGrpEntry 4 } srmTargetSlotLineNum OBJECT-TYPE SYNTAX Integer32 (0..8) MAX-ACCESS read-write STATUS current DESCRIPTION "0 means not assigned. There is no default value for this object." ::= { srm3T3CnfGrpEntry 5 } -- ******************************************************************* -- -- srmeCnfGrpTable: -- This table contains DS1 and E1 mapping configuration for SRME card. -- This group is card specific for SRME card. -- -- ******************************************************************* srmeCnfGrpTable OBJECT-TYPE SYNTAX SEQUENCE OF SrmeCnfGrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SRME configuration table for bulk distribution of SRME lines." ::= { srmeCnfGrp 1 } srmeCnfGrpEntry OBJECT-TYPE SYNTAX SrmeCnfGrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "an entry in the SRME Distribution configuration table" INDEX { srmeLineNum, srmeStartVtNum } ::= { srmeCnfGrpTable 1 } SrmeCnfGrpEntry ::= SEQUENCE { srmeLineNum Integer32, srmeStartVtNum Integer32, srmeRowStatus INTEGER, srmeTargetSlotNum Integer32, srmeTargetSlotLineNum Integer32, srmeVtFramingType INTEGER } srmeLineNum OBJECT-TYPE SYNTAX Integer32 (1..3) MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the SRME line number. For OC3/STM1: SYNTAX Integer32 1 There is no default value for this object." ::= { srmeCnfGrpEntry 1 } srmeStartVtNum OBJECT-TYPE SYNTAX Integer32 (1..84) MAX-ACCESS read-only STATUS current DESCRIPTION "The start T1 or E1 number (virtual tributary) to be affected. For OC3 with T1 tributaries: SYNTAX Integer32 (1 .. 84) For STM1 with E1 tributaries: SYNTAX Integer32 (1 .. 63) There is no default value for this object." ::= { srmeCnfGrpEntry 2 } srmeRowStatus OBJECT-TYPE SYNTAX INTEGER { add (1), delete (2), modify (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Command used to add, delete, or modify one or more T1 or E1 mappings. Only the srmeVtFramingType object can be modified once the distribution link is added. To modify all other objects, user should first delete the link and add it again. Default value is modify(3)." ::= { srmeCnfGrpEntry 3 } srmeTargetSlotNum OBJECT-TYPE SYNTAX Integer32 (1..32) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the target slot number to be linked. There is no default value for this object. For MGX8x50: SRM01 services slots 1 - 6 and 9 - 14, SRM02 services slots 17 - 22 and 25 - 30 For MGX8x30: service slots 3-6 and 10-13." ::= { srmeCnfGrpEntry 4 } srmeTargetSlotLineNum OBJECT-TYPE SYNTAX Integer32 (0..8) MAX-ACCESS read-write STATUS current DESCRIPTION "Specify the target slot's line to be linked. The value zero means, the target line number is not assigned. There is no default value for this object." ::= { srmeCnfGrpEntry 5 } srmeVtFramingType OBJECT-TYPE SYNTAX INTEGER { notApplicable (1), sf (2), esf (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the Framing Type of the target slot line. This is applicable only if the target module is a T1 Service Module and byte sync mapping is used on SRME. Not applicable to E1 Service Modules. sf: Superframe or D4 esf: Extended Superframe. Default is 'esf' if SRME lines are configured for byte-synchronous mapping, Else, the default is notApplicable." ::= { srmeCnfGrpEntry 6 } -- conformance information ciscoWanSrmMIBConformance OBJECT IDENTIFIER ::= { ciscoWanSrmMIB 2 } ciscoWanSrmMIBGroups OBJECT IDENTIFIER ::= { ciscoWanSrmMIBConformance 1 } ciscoWanSrmMIBCompliances OBJECT IDENTIFIER ::= { ciscoWanSrmMIBConformance 2 } -- compliance statements ciscoWanSrmCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for objects related to SRM MIB." MODULE -- this module GROUP ciscoWanSrmConfGroup DESCRIPTION "This group is mandatory for those products where SRM is used for bulk distribution." GROUP ciscoWanSrmeConfGroup DESCRIPTION "This group is mandatory for those products where SRM-E is used for bulk distribution." ::= { ciscoWanSrmMIBCompliances 1 } ciscoWanSrmConfGroup OBJECT-GROUP OBJECTS { srmT3LineNum, srmStartT1LineNum, srmT1RowStatus, srmTargetSlotNum, srmTargetSlotLineNum } STATUS current DESCRIPTION "The collection of objects which are used for configuring bulk distribution for SRM module." ::= { ciscoWanSrmMIBGroups 1 } ciscoWanSrmeConfGroup OBJECT-GROUP OBJECTS { srmeLineNum, srmeStartVtNum, srmeRowStatus, srmeTargetSlotNum, srmeTargetSlotLineNum, srmeVtFramingType } STATUS current DESCRIPTION "The collection of objects which are used for configuring bulk distribution for SRM-E module." ::= { ciscoWanSrmMIBGroups 2 } END