-- ***************************************************************** -- BERT MIB: Bit Error Rate Testing MIB for MGX82xx series products. -- -- August 2002, Subra Hegde -- -- Copyright (c) 2002 by cisco Systems, Inc. -- All rights reserved. -- ***************************************************************** CISCO-WAN-SRM-BERT-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF DisplayString FROM SNMPv2-TC axisDiagnostics FROM BASIS-MIB ciscoWan FROM CISCOWAN-SMI; ciscoWanSrmBertMIB MODULE-IDENTITY LAST-UPDATED "200208260000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-wanatm@cisco.com" DESCRIPTION "The MIB Module for BERT(Bit Error Rate Testing) using Service Resource Module(SRM). This MIB module is used for BERT on FRSM, AUSM, CESM, VISM modules. This module contains information on results from BERT tests using DDS(Digital Data Service) pattern." REVISION "200208260000Z" DESCRIPTION "Initial version of the MIB. The content of this MIB was originally available in CISCO-WAN-AXIPOP-MIB defined using SMIv1. The applicable objects from CISCO-WAN-AXIPOP-MIB are defined using SMIv2 in this MIB. Also the descriptions of some of the objects have been modified." ::= { ciscoWan 31 } bert OBJECT IDENTIFIER ::= { axisDiagnostics 1 } bertControl OBJECT-TYPE SYNTAX INTEGER { acquireBert (1), releaseBert (2), cnfBert (3), startBert (4), modBert (5), delBert (6) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object controls all the SET operations on this MIB group. acquireBert : Acquire BERT resources. cnfBert : Configure the required BERT test. startBert : The configured test has to be started. modBert : Modify parameters for the ongoing BERT test. delBert : Running BERT test has to be stopped. The above list shows the sequence in which the SET operations on this group need to be done, ideally. Bert can be operated upon only with bertUserId and bertSlotNumber. The default value is 0, means no action." ::= { bert 1 } bertResourceStatus OBJECT-TYPE SYNTAX INTEGER { free (1), inUse (2), cleanupPending (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "All of bert resources can be used by only one user at a time. This gives the status of the resources." DEFVAL { free } ::= { bert 2 } bertOwner OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This refers to the user who owns the BERT resources. If the user is a CLI user, then this is username. If it is SNMP Manager(For example Cisco Wan Manager), then this would be the IP address. For example, this value can be, 192.9.209.157 within quotes." ::= { bert 3 } bertUserId OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "This identifies the user who wants to do a SET operation on this group. This will be compared against bertOwner and access will be given only if it matches. Hence, for every SET request, this object should have a valid value. If the user is a CLI user, then this is username. If it is SNMP Manager, then this would be the IP address. For example, this value can be, 192.9.209.157 within quotes. Required for bert operations." ::= { bert 4 } bertStatus OBJECT-TYPE SYNTAX INTEGER{ inactive (1), bertInSync (2), bertOutOfSync (3), searchingDDSCommands (4), farEndInLoop (5), facilityInLoop (6), portFacilityFifoFault (7), portFacilityFifoOutOfSync (8), metallicInLoop (9), bertFailed (10) } MAX-ACCESS read-only STATUS current DESCRIPTION "This variable provides the status of BERT in the shelf." DEFVAL { inactive } ::= { bert 5 } bertSlotNumber OBJECT-TYPE SYNTAX Integer32 (1..30) MAX-ACCESS read-write STATUS current DESCRIPTION "specifies the physical slot number of the Service Module which is to run BERT For MGX 8220, the range is 5-14. For MGX 8850, the range is 1-6, 9-14, 17-22, 25-30. Required for bert operations." ::= { bert 6 } bertTestMedium OBJECT-TYPE SYNTAX INTEGER { port(1), line(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "specifies whether the bert is to test a port or an entire T1/E1 line. No default value for this, it has to be set if bert is configured." ::= { bert 7 } bertPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "specifies the port number for BERT." ::= { bert 8 } bertLine OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "specifies the line number for BERT. If the test medium is port, this represents the line to which the port belongs." ::= { bert 9 } bertMode OBJECT-TYPE SYNTAX INTEGER { bertPatternTest (1), ddsSeek (2), loopback (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "specifies the mode, the BERT module is to be configured for." ::= { bert 10 } bertDeviceToLoop OBJECT-TYPE SYNTAX INTEGER { noLatchOCUwith1 (1), noLatchOCUwitout1 (2), noLatchCSU (3), noLatchDSU (4), latchDS0Drop (5), latchDS0Line (6), latchOCU (7), latchCSU (8), latchDSU (9), latchHL96 (10), v54Polynomial (11), inband (12), esf (13), metallic (14), noDevice (15), smartJackInband (16) } MAX-ACCESS read-write STATUS current DESCRIPTION "This shows the type of the end device and the type of the loopback used (latching/nonlatching/polynomial)." ::= { bert 11 } bertDS0DPIterationCount OBJECT-TYPE SYNTAX Integer32 (1..32) MAX-ACCESS read-write STATUS current DESCRIPTION "The Iteration Register needs to be programmed in SRM when DSO drop loop option is selected in bertDeviceToLoop. The value to be programmed there is minus one of this object value, since the register is 0 based. DSP-OP devices can be cross connected in the centeral office. By this, the user has capablitiy to put any of the devices in the chain in loopback mode. This is done by repeating the latching activation code in a specific manner. The binary number in the iterataion register determines how many times the first portion of a latching loop activation code needs to be repeated as per user request and according to the Bellcore spec. A value of 0 results in no iteration and will cause the very first device in chain to go into loop back. A value of 1 will result into one iteration and will cause the second device to go into loopback and so on. The range of this count is 1 to 32, and it would translate to a range of 0 to 31 for the iteration register." ::= { bert 12 } bertPattern OBJECT-TYPE SYNTAX INTEGER { allZeros (1), allOnes (2), alternateONeZero (3), doubleOneZero (4), fifteenBit (5), twentyBit (6), twentyBitQRSS (7), twentythreeBit (8), oneInEight (9), threeIntwentyfour (10), dds-1 (11), dds-2 (12), dds-3 (13), dds-4 (14), dds-5 (15), nineBit (16), elevenBit (17) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable determines BERT pattern to be transmitted." ::= { bert 13 } bertLoopback OBJECT-TYPE SYNTAX INTEGER { farEndLoopback (1), facilityLoopback (2), metallicLoopback (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "specifies the type of loopback to be (d)established." ::= { bert 14 } bertLoopbackOperation OBJECT-TYPE SYNTAX INTEGER{ loopUp (1), loopDown (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "specifies the operation of loopback (up or down)." ::= { bert 15 } bertDS0Speed OBJECT-TYPE SYNTAX INTEGER { speed56k (1), speed64k (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "represents the ds0 speed of the test running." ::= { bert 16 } bertTimeSlots OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "represents the number of ds0s in the test medium chosen." ::= { bert 17 } bertStartTime OBJECT-TYPE SYNTAX DisplayString (SIZE (8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The syntax is hh:mm:ss The time zone is as configured in the shelf." ::= { bert 18 } bertStartDate OBJECT-TYPE SYNTAX DisplayString (SIZE (10)) MAX-ACCESS read-only STATUS current DESCRIPTION "On MGX 8220, the syntax is mm/dd/yy On MGX 8850, the syntax is mm/dd/yyyy." ::= { bert 19 } bertBitCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This shows the number of bits transmitted." ::= { bert 20 } bertBitErrorCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This shows the number of bits received in error." ::= { bert 21 } bertErrorInjectCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This shows the number of times error was injected." ::= { bert 22 } bertCleanupAction OBJECT-TYPE SYNTAX INTEGER { noAction (1), smCleanup (2), latchDS0DropLoopdown (3), latchDS0LineLoopdown (4), latchOCULoopdown (5), latchCSULoopdown (6), latchDSULoopdown (7), latchHL96Loopdown (8), v54PolynomialLoopdown (9), inbandLoopdown (10), esfLoopdown (11), facilityLoopdown (12), metallicLoopdown (13), smartJackInbandLoopdown (14) } MAX-ACCESS read-only STATUS current DESCRIPTION "When the BERT has to be stopped or aborted (due to card state changes), this object would give the exact action to take. The bert related changes to the shelf, then, can be cleaned up. When its value is a Loopdown, it implies smCleanup plus the corresponding Loopdown." DEFVAL { noAction } ::= { bert 23 } bertAbortReason OBJECT-TYPE SYNTAX INTEGER { ascStateChange (1), smStateChange (2), srmStateChange (3), coreCardSwitch (4), smRedundancySwitch (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "when the BERT is aborted, this object would give the reason for that." ::= { bert 24 } -- ---------------------------------------------------------------------- -- -- This table consists of the last 20 DDS codes that were detected during -- DDS seek. -- ---------------------------------------------------------------------- -- ---------------------------------------------------------------------- -- -- If one of the indices to the table is 0, it means that there are no -- entries in the table. This table is a circular one and the first and -- last indices refer to the beginning and the end of the circular list -- respectively. If there are more than 20 codes detected, the table -- enrties will be overwritten to keep only the last 20 codes detected. -- -- ---------------------------------------------------------------------- bertDDSSeekResultsTableFirstIndex OBJECT-TYPE SYNTAX Integer32 (0..20) MAX-ACCESS read-only STATUS current DESCRIPTION "Denotes the index of the oldest entry in the table. A value of zero means that there are no entries in the table." ::= { bert 25 } bertDDSSeekResultsTableLastIndex OBJECT-TYPE SYNTAX Integer32 (0..20) MAX-ACCESS read-only STATUS current DESCRIPTION "Denotes the index of the latest entry in the table. A value of zero means that there are no entries in the table." ::= { bert 26 } bertDDSSeekResultsTable OBJECT-TYPE SYNTAX SEQUENCE OF BertDDSSeekResultsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains all available DDS patterns detected and latched by an interaface(lines,ports etc) configured to detect DDS patterns." ::= { bert 27 } bertDDSSeekResultsTableEntry OBJECT-TYPE SYNTAX BertDDSSeekResultsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the detected DDS codes table." INDEX { bertDDSSeekResultsTableIndex } ::= { bertDDSSeekResultsTable 1 } BertDDSSeekResultsTableEntry ::= SEQUENCE { bertDDSSeekResultsTableIndex Integer32, bertDDSCode INTEGER } bertDDSSeekResultsTableIndex OBJECT-TYPE SYNTAX Integer32 (1..20) MAX-ACCESS read-only STATUS current DESCRIPTION "Denotes the serial number of the entry in the table." ::= { bertDDSSeekResultsTableEntry 1 } bertDDSCode OBJECT-TYPE SYNTAX INTEGER { abnormalStationCondition (30), -- ('1E'h), block (10), -- ('0A'h), channelLoopback (40), -- ('28'h), dsuLoopback (44), -- ('2C'h), farEndVoice (90), -- ('5A'h), idle (126), -- ('7E'h), loopbackEnable (86), -- ('56'h), mjuAlert (114), -- ('72'h), muxOutOfSync (26), -- ('1A'h), ocuLoopback (42), -- ('2A'h), release (120), -- ('78'h), test (28), -- ('1C'h), testAlert (108), -- ('6C'h), transitionInProgress (58), -- ('3A'h), unassignedMuxChannel (24), -- ('18'h), unnamed (50) -- ('32'h) } MAX-ACCESS read-only STATUS current DESCRIPTION "Denotes the type of DDS code detected." ::= { bertDDSSeekResultsTableEntry 2 } -- -------------------------------------------------------------------- -- -- This table contains the list of supported tests for each SM in -- the shelf. -- -- -------------------------------------------------------------------- bertSupportedTestsTable OBJECT-TYPE SYNTAX SEQUENCE OF BertSupportedTestsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of supported tests for a given SM." ::= { bert 28 } bertSupportedTestsTableEntry OBJECT-TYPE SYNTAX BertSupportedTestsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A general supported tests entry." INDEX { bertSupportedTestsTableIndex } ::= { bertSupportedTestsTable 1 } BertSupportedTestsTableEntry ::= SEQUENCE { bertSupportedTestsTableIndex Integer32, bertSupportFlag INTEGER, bertTestMediumMask Integer32, bertModeMask Integer32, bertDeviceToLoopMask Integer32, bertPatternMask Integer32, bertLoopbackMask Integer32, bertCardT1E1Type INTEGER } bertSupportedTestsTableIndex OBJECT-TYPE SYNTAX Integer32 (1..30) MAX-ACCESS read-only STATUS current DESCRIPTION "This index is the physical slot number of the Service Module whose entry it represents in the table. For MGX 8220, the range is 5-14. For MGX 8850, the range is 1-6, 9-14, 17-22, 25-30." ::= { bertSupportedTestsTableEntry 1 } bertSupportFlag OBJECT-TYPE SYNTAX INTEGER { yes (1), no (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "'yes' if the table entry correctly represents the supported tests for the SM on the corresponding slot. 'no' if no tests at all are supported." ::= { bertSupportedTestsTableEntry 2 } bertTestMediumMask OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Every test medium is represented by a bit of mask. Bits 0-1 are valid in this integer. The meaning of the mask can be understood from the example below: -------------------------- TestMedium | SM | support -------------------------- port | 1 line | 1 -------------------------- (Table contents applicable to FRSM-4T1) bertTestMediumMask = 11 binary The column titles represent the variables bertTestMedium depends on. The mask is represented in column major order." ::= { bertSupportedTestsTableEntry 3 } bertModeMask OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Every mode is represented by 2 bits of mask. Bits 0-5 are valid in this integer. The meaning of the mask can be understood from the example below: ----------------------------------------------------------- Mode | SM support | Test Medium: | | Multiple | | T1 time slots ----------------------------------------------------------- Pattern test | 1 | 1 DDS seek | 1 | 0 Loopback | 1 | 1 ----------------------------------------------------------- (Table contents applicable to FRSM-4T1) bertModeMask = 101111 binary The column titles represent the variables bertMode depends on. The mask is represented in column major order." ::= { bertSupportedTestsTableEntry 4 } bertDeviceToLoopMask OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Every class of devices to loop is represented by 6 bits of mask. Bits 0-29 are valid in this integer. The meaning of the mask can be understood from the example below: ----------------------------------------------------------- | | | Test Medium Class of | SM | MODE |________________________________ devices |supp | Loopback|Line |multiple T1 | 64k | 56k | | | | time slots | | ----------------------------------------------------------- noLatch | 1 0 0 0 0 1 latch | 1 1 0 0 1 1 v54 | 1 1 0 1 1 1 inband/esf| 1 1 1 0 0 0 metallic | 1 0 1 0 0 0 ----------------------------------------------------------- (Table contents applicable to FRSM-4T1) bertDeviceToLoopMask = 001110011000100110000111011111 binary The column titles represent the variables bertDeviceToLoop depends on. The mask is represented in column major order. Due to the limitation on the length of the mask, 'noDevice' option is not represented in this mask. But, the mask for it, is assumed to be a row of ones except for a zero on 'MODE Loopback' column." ::= { bertSupportedTestsTableEntry 5 } bertPatternMask OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Every class of patterns is represented by 2 bits of mask. Bits 0-3 are valid in this integer. The meaning of the mask can be understood from the example below: ---------------------------------------------- Class of | SM | Non latching patterns | support |device to loop ---------------------------------------------- Other patterns | 1 | 0 ---------------------------------------------- Patterns | 1 | 1 power 9 and 11 | | ---------------------------------------------- (Table contents applicable to FRSM-4T1) bertPatternMask = 1011 binary The column titles represent the variables bertPattern depends on. The mask is represented in column major order." ::= { bertSupportedTestsTableEntry 6 } bertLoopbackMask OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Every loopback is represented by 2 bits of mask. Bits 0-5 are valid in this integer. The meaning of the mask can be understood from the example below: ---------------------------------------------- Loopback | SM | Test Medium | support | Port ---------------------------------------------- Far End Loopback | 1 | 1 Facility Loopback | 1 | 1 Metallic Loopback | 1 | 0 ---------------------------------------------- (Table contents applicable to FRSM-4T1) bertLoopbackMask = 011111 binary The column titles represent the variables bertLoopback depends on. The mask is represented in column major order." ::= { bertSupportedTestsTableEntry 7 } bertCardT1E1Type OBJECT-TYPE SYNTAX INTEGER { t1(1), e1(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies whether a t1 or e1 card." ::= { bertSupportedTestsTableEntry 8 } -- conformance information ciscoWanSrmBertMIBConformance OBJECT IDENTIFIER ::= { ciscoWanSrmBertMIB 2 } ciscoWanSrmBertMIBGroups OBJECT IDENTIFIER ::= { ciscoWanSrmBertMIBConformance 1 } ciscoWanSrmBertMIBCompliances OBJECT IDENTIFIER ::= { ciscoWanSrmBertMIBConformance 2 } -- compliance statements ciscoWanSrmBertCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for objects related to Bert MIB." MODULE -- this module MANDATORY-GROUPS { ciscoWanSrmBertConfGroup } ::= { ciscoWanSrmBertMIBCompliances 1 } ciscoWanSrmBertConfGroup OBJECT-GROUP OBJECTS { bertControl, bertResourceStatus, bertOwner, bertUserId, bertStatus, bertSlotNumber, bertTestMedium, bertPort, bertLine, bertMode, bertDeviceToLoop, bertDS0DPIterationCount, bertPattern, bertLoopback, bertLoopbackOperation, bertDS0Speed, bertTimeSlots, bertStartTime, bertStartDate, bertBitCount, bertBitErrorCount, bertErrorInjectCount, bertCleanupAction, bertAbortReason } STATUS current DESCRIPTION "The collection of objects which are used for configuring/running BERT on Service modules using SRM module." ::= { ciscoWanSrmBertMIBGroups 1 } ciscoWanSrmBertTestResultsGroup OBJECT-GROUP OBJECTS { bertSupportedTestsTableIndex, bertSupportFlag, bertTestMediumMask, bertModeMask, bertDeviceToLoopMask, bertPatternMask, bertLoopbackMask, bertCardT1E1Type } STATUS current DESCRIPTION "The collection of objects which are used for finding the results of running BERT tests." ::= { ciscoWanSrmBertMIBGroups 2 } ciscoWanSrmBertDDSResultsGroup OBJECT-GROUP OBJECTS { bertDDSSeekResultsTableFirstIndex, bertDDSSeekResultsTableLastIndex, bertDDSSeekResultsTableIndex, bertDDSCode } STATUS current DESCRIPTION "The collection of objects which are used for finding the results of running BERT tests using DDS pattern." ::= { ciscoWanSrmBertMIBGroups 3 } END