-- ***************************************************************** -- CISCO-WAN-LAPD-TRUNK-MIB.my: CISCO WAN LAPD Trunk MIB file -- -- December 2003, George Ogagan -- -- Copyright (c) 2001-2003 by Cisco Systems, Inc. -- All rights reserved. -- -- ***************************************************************** CISCO-WAN-LAPD-TRUNK-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, Integer32, Counter32, OBJECT-TYPE FROM SNMPv2-SMI RowStatus FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF voice FROM BASIS-MIB ciscoWan FROM CISCOWAN-SMI; ciscoWanLapdTrunkMIB MODULE-IDENTITY LAST-UPDATED "200312110000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-vism@cisco.com" DESCRIPTION "The MIB module is defined for establishing a Trunk to transport PRI (Primary Rate Interface) signaling information over a RUDP (Reliable UDP) connection for CCS (Common Channel Signaling) VoIP(Voice Over IP) Trunking application." REVISION "200312110000Z" DESCRIPTION "Update descriptions in the MIB. " REVISION "200307170000Z" DESCRIPTION "-Added following tables: vismLapdTable vismLapdStatsTable vismLapdDlcTable These tables were defined in vismLapd.my earlier. and are now converted to SMIv2 and defined here. - Added UNITS clause wherever applicable." REVISION "200307110000Z" DESCRIPTION "Initial version of the MIB. The content of this MIB was originally available in SMIv1 version. The MIB has been converted to SMIv2 version and descriptions of some of the objects have been modified." ::= { ciscoWan 23 } vismLapdGrp OBJECT IDENTIFIER ::= { voice 12 } ciscoWanLapdTrunkMIBObjects OBJECT IDENTIFIER ::= { ciscoWanLapdTrunkMIB 1 } vismLapdTrunkGrp OBJECT IDENTIFIER ::= { ciscoWanLapdTrunkMIBObjects 1 } -- -- vismLapdTrunkGrpTable -- vismLapdTrunkGrpTable OBJECT-TYPE SYNTAX SEQUENCE OF VismLapdTrunkGrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table defines attributes used to set up a Trunked LAPD (Link Access Procedure on the D-channel) connection over RUDP between 2 VISM's to transport PRI D channel information. Such a Trunked connection over RUDP can only be created if the D-channel has already not been configured for PRI Backhaul. The object vismLapdTrunkType in vismLapdTable indicate PRI Backhaul or Trunking is configured, also an entry will be created for each D channel. PRI Backhaul and PRI Trunking can co-exist on the same card but not on the same line, a line (DS1) is associated with a LAPD RUDP through vismLapdTrunkRudpIndex. " ::= { vismLapdTrunkGrp 1 } vismLapdTrunkGrpEntry OBJECT-TYPE SYNTAX VismLapdTrunkGrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the vismLapdTrunkGrpTable. " INDEX { vismLapdTrunkNum } ::= { vismLapdTrunkGrpTable 1 } VismLapdTrunkGrpEntry ::= SEQUENCE { vismLapdTrunkNum Integer32, vismLapdTrunkState INTEGER, vismLapdTrunkRudpIndex Integer32, vismLapdTrunkRowStatus RowStatus } vismLapdTrunkNum OBJECT-TYPE SYNTAX Integer32(0..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is the index of vismLapdTrunkGrpTable. " ::= { vismLapdTrunkGrpEntry 1 } vismLapdTrunkState OBJECT-TYPE SYNTAX INTEGER { oos (1), is (2), unknown (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "'oos' - Out of service state. The LAPD Trunk state is independent of the RUDP session state in the sense that the LAPD state could be 'oos' while the RUDP session state is 'is' and vice versa. 'is' - In service state. 'unknown' - This is the state other than the above states. If the communication is lost between the 2 VISM's, the state of this connection becomes 'oos'. " ::= { vismLapdTrunkGrpEntry 2 } vismLapdTrunkRudpIndex OBJECT-TYPE SYNTAX Integer32(0..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "All LAPD Trunk connections are over RUDP. Each RUDP connection is characterized by a set of negotiable and non-negotiable parameters. These parameters are in vismRudpSessionCnfEntry(defined in CISCO-VISM-SESSION-MIB MIB) table. This object is an index into that table. Before creating an entry in this table the corresponding RUDP session entry must be created in the vismRudpSessionCnfEntry table with the vismRudpSessionType(defined in the same MIB) as LAPD Trunking. The RUDP session cannot be deleted if the corresponding LAPD Trunk still exist. The LAPD Trunk needs to be deleted before deleting RUDP session as specified in CISCO-VISM-SESSION-MIB. " ::= { vismLapdTrunkGrpEntry 3 } vismLapdTrunkRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable allows the user to add or delete the entry for this table. 'createAndGo': Use this to add a LAPD Trunk connection in this table. The vismLapdTrunkRudpIndex for this corresponding entry has to be specified also. 'active': This value is returned, once the row is created. 'destroy': Use this to delete a LAPD Trunk connection from this table. " ::= { vismLapdTrunkGrpEntry 4 } -- LAPD configuration table. vismLapdTable OBJECT-TYPE SYNTAX SEQUENCE OF VismLapdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used for maintaining the configuration of the LAPD channel on VISM. " ::= { vismLapdGrp 1 } vismLapdEntry OBJECT-TYPE SYNTAX VismLapdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry for vismLapdTable." INDEX { vismLapdIndex } ::= { vismLapdTable 1 } VismLapdEntry ::= SEQUENCE { vismLapdIndex Integer32, vismLapdAppType INTEGER, vismLapdWinSize Integer32, vismLapdN200 Integer32, vismLapdT200 Integer32, vismLapdT203 Integer32, vismLapdType INTEGER, vismLapdRowStatus RowStatus, vismLapdSide INTEGER, vismLapdTrunkType INTEGER } vismLapdIndex OBJECT-TYPE SYNTAX Integer32(1..248) MAX-ACCESS read-only STATUS current DESCRIPTION "This is an index to vismLapdTable. This is derived from the following formula: index = 31 * (DS1# - 1) + DS0# where : DS1# - The T1/E1 line number in the range 1 - 8. DS0# - The DS0 channel number ranging from 1 to 24 for T1 and 1 to 31 for E1. " ::= { vismLapdEntry 1 } vismLapdAppType OBJECT-TYPE SYNTAX INTEGER { pri(1), gr-303(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the type of the LAPD interface. When the user creates a LAPD entry this object need to be specified. After creation it cannot be modified. 'pri' - level of service provided by ISDN(Integrated Services Digital Network) that carries voice, data, other services with control and signaling information in D-channel. 'gr-303' - standard interfaces for integrated digital loop carrier systems. " DEFVAL { pri } ::= { vismLapdEntry 2 } vismLapdWinSize OBJECT-TYPE SYNTAX Integer32 (1..127) MAX-ACCESS read-create STATUS current DESCRIPTION "The window size - maximum number of sequentially numbered I-frames that may be outstanding. " DEFVAL { 7 } ::= { vismLapdEntry 3 } vismLapdN200 OBJECT-TYPE SYNTAX Integer32 (1..10) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of retransmissions of a frame. " DEFVAL { 3 } ::= { vismLapdEntry 4 } vismLapdT200 OBJECT-TYPE SYNTAX Integer32 (100..1023000) UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of time in milliseconds to wait for acknowledgement for a transmit frame. This value should be less than vismLapdT203. For PRI, the range is 1000 ms to 1023000 ms. The default is 1000 ms. For GR-303, the range is 100 ms to 350 ms in increments of 50 ms. The default value is 150 ms. " ::= { vismLapdEntry 5 } vismLapdT203 OBJECT-TYPE SYNTAX Integer32 (1000..1023000) UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum time (in milliseconds) allowed without frames being exchanged. This value should be greater than vismLapdT200. For PRI, the range is 1000 to 1023000 and the default is 10000 ms. For GR-303, the range is 10000 to 300000 ms in increments of 10000 ms. The default is 30000 ms. " ::= { vismLapdEntry 6 } vismLapdType OBJECT-TYPE SYNTAX INTEGER { ccitt(1), att5EssPRA(3), att4Ess(4), ntDMS100PRA(6), vn2or3(7), insNet(8), tr6MPC(9), tr6PBX(10), ausp(12), ni1(13), etsi(14), bc303TMC(15), bc303CSC(16), ntDMS250(17), bellcore(18), ni2(19) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies what type of interface the LAPD stack will be used with. ccitt(1) : CCITT att5EssPRA(3) : AT&T 5ESS PRA att4Ess(4) : AT&T 4ESS ntDMS100PRA(6) : NT dms100 PRA vn2or3(7) : VN 2 or VN 3 insNet(8) : INS Net tr6MPC(9) : tr6 MPC tr6PBX(10) : tr6 PBX ausp(12) : Austel Primary ni1(13) : National ISDN-1 etsi(14) : ETSI bc303TMC(15) : Bellcorp tr303 tmc bc303CSC(16) : Bellcorp tr303 csc ntDMS250(17) : NT dms250 bellcore(18) : Bellcore ni2(19) : National ISDN-2 " DEFVAL { ni2 } ::= { vismLapdEntry 7 } vismLapdRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Row status allows users to create or delete a LAPD entry. 'createAndGo' - this option is use to create an entry in the table. Before a LAPD entry is created, the session manager should be set up(add a PRI backhaul session set, and session group between VISM and the call agent). Before creating a LAPD entry the entry in HDLC table will implicitly created first. If the DS0 has already been used then the request of creating a LAPD channel on the same DS0 on the same line will be rejected. After creating the LAPD entry the corresponding entry in vismLapdStatsTable will be implicitly created. 'active' - When an entry is created it becomes active. 'destroy' - Use this to delete an entry in this table. After implicitly deleting all the entries(if there is any) in vismLapdDlcEntry table for the specific D channel the entry in vismLapdEntry will be deleted, then the entry in vismLapdStatsTable will be implicitly deleted, followed by the deletion of the HDLC entry. " ::= { vismLapdEntry 8 } vismLapdSide OBJECT-TYPE SYNTAX INTEGER { network(1), user(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies whether LAPD stack is on the user side or network side. This object can be set when the row is created. It cannot be modified for an existing row. " DEFVAL { network } ::= { vismLapdEntry 9 } vismLapdTrunkType OBJECT-TYPE SYNTAX INTEGER { backhaul (1), lapdTrunking (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates if the line is configured for Trunking or PRI Backhaul. This object is set to the appropriate type when the vismRudpSessionType (defined in CISCO-VISM-SESSION-MIB MIB) parameter in the vismRudpSessionCnfEntry(specify in the same MIB) table is set. The motivation to have similar such objects at two places is for convenience. " ::= { vismLapdEntry 10 } -- vismLapdStatsTable vismLapdStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF VismLapdStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains statistics information for all LAPD (D channel Data Link) interfaces on VISM. " ::= { vismLapdGrp 2 } vismLapdStatsEntry OBJECT-TYPE SYNTAX VismLapdStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the LAPD Table." INDEX { vismLapdStatsIndex } ::= { vismLapdStatsTable 1 } VismLapdStatsEntry ::= SEQUENCE { vismLapdStatsIndex Integer32, vismLapdRxInfoFrames Counter32, vismLapdTxInfoFrames Counter32, vismLapdRxReadyFrames Counter32, vismLapdTxReadyFrames Counter32, vismLapdRxNotReadyFrames Counter32, vismLapdTxNotReadyFrames Counter32, vismLapdRxSABMFrames Counter32, vismLapdTxSABMFrames Counter32, vismLapdRxDisconFrames Counter32, vismLapdTxDisconFrames Counter32, vismLapdRxUAFrames Counter32, vismLapdTxUAFrames Counter32, vismLapdRxDiscModeFrames Counter32, vismLapdTxDiscModeFrames Counter32, vismLapdRxFrmRejectFrames Counter32, vismLapdTxFrmRejectFrames Counter32, vismLapdRxExchIdFrames Counter32, vismLapdTxExchIdFrames Counter32, vismLapdRxUnumInfoFrames Counter32, vismLapdTxUnumInfoFrames Counter32, vismLapdRxRejectFrames Counter32, vismLapdTxRejectFrames Counter32, vismLapdRxInvalidFrames Counter32 } vismLapdStatsIndex OBJECT-TYPE SYNTAX Integer32(1..248) MAX-ACCESS read-only STATUS current DESCRIPTION "This is the index for this table. It is the same as vismLapdIndex. An entry of this table will be implicitly created when a LAPD entry is added. " ::= { vismLapdStatsEntry 1 } vismLapdRxInfoFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter contains received information frames on a LAPD. " ::= { vismLapdStatsEntry 2 } vismLapdTxInfoFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter contains information frames transmitted on a LAPD. " ::= { vismLapdStatsEntry 3 } vismLapdRxReadyFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter contains Receiver Ready frames received on a LAPD. " ::= { vismLapdStatsEntry 4 } vismLapdTxReadyFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter contains Receiver Ready frames transmitted on LAPD. " ::= { vismLapdStatsEntry 5 } vismLapdRxNotReadyFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter contains Receiver Not Ready frames received on LAPD. " ::= { vismLapdStatsEntry 6 } vismLapdTxNotReadyFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter contains Receiver Not Ready frames transmitted on a LAPD. " ::= { vismLapdStatsEntry 7 } vismLapdRxSABMFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter contains Set Asynchronous Balanced Mode frames received on a LAPD. " ::= { vismLapdStatsEntry 8 } vismLapdTxSABMFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter contains Set Asynchronous Balanced Mode frames transmitted on LAPD. " ::= { vismLapdStatsEntry 9 } vismLapdRxDisconFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter contains Disconnect frames received on LAPD. " ::= { vismLapdStatsEntry 10 } vismLapdTxDisconFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter contains Disconnect frames transmitted on LAPD. " ::= { vismLapdStatsEntry 11 } vismLapdRxUAFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter contains Unnumbered Acknowledge frames received on a LAPD. " ::= { vismLapdStatsEntry 12 } vismLapdTxUAFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter contains Unnumbered Acknowledge frames transmitted on a LAPD. " ::= { vismLapdStatsEntry 13 } vismLapdRxDiscModeFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter contains Disconnect Mode frames received on a LAPD. " ::= { vismLapdStatsEntry 14 } vismLapdTxDiscModeFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter contains Disconnect Mode frames transmitted on a LAPD. " ::= { vismLapdStatsEntry 15 } vismLapdRxFrmRejectFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter contains Frame Reject frames received on a LAPD. " ::= { vismLapdStatsEntry 16 } vismLapdTxFrmRejectFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter contains Frame Reject frames transmitted on a LAPD. " ::= { vismLapdStatsEntry 17 } vismLapdRxExchIdFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter contains Exchange Id frames received on a LAPD. " ::= { vismLapdStatsEntry 18 } vismLapdTxExchIdFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter contains Exchange Id frames transmitted on a LAPD. " ::= { vismLapdStatsEntry 19 } vismLapdRxUnumInfoFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter contains Unnumbered Information frames received on a LAPD. " ::= { vismLapdStatsEntry 20 } vismLapdTxUnumInfoFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter contains Unnumbered Information frames transmitted on a LAPD. " ::= { vismLapdStatsEntry 21 } vismLapdRxRejectFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter contains Received Reject Frames on a LAPD. " ::= { vismLapdStatsEntry 22 } vismLapdTxRejectFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter contains Reject frames transmitted on LAPD. " ::= { vismLapdStatsEntry 23 } vismLapdRxInvalidFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter contains Invalid frames received on a LAPD. " ::= { vismLapdStatsEntry 24 } -- vismLapdDlcTable vismLapdDlcTable OBJECT-TYPE SYNTAX SEQUENCE OF VismLapdDlcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used for maintaining the link state of different DLCs on a LAPD channel. An entry of this table will be implicitly created when a LAPD entry is added. " ::= { vismLapdGrp 3 } vismLapdDlcEntry OBJECT-TYPE SYNTAX VismLapdDlcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry for vismLapdDlcTable." INDEX { vismLapdDlcIndex, vismLapdDlcSapi, vismLapdDlcTei } ::= { vismLapdDlcTable 1 } VismLapdDlcEntry ::= SEQUENCE { vismLapdDlcIndex Integer32, vismLapdDlcSapi Integer32, vismLapdDlcTei Integer32, vismLapdDlcLinkState INTEGER } vismLapdDlcIndex OBJECT-TYPE SYNTAX Integer32(1..248) MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the corresponding LAPD index. It is the same as vismLapdIndex. " ::= { vismLapdDlcEntry 1 } vismLapdDlcSapi OBJECT-TYPE SYNTAX Integer32(0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This is the SAPI(Service Access Point Identifier) of a specific DLC(Data Link Control). " ::= { vismLapdDlcEntry 2 } vismLapdDlcTei OBJECT-TYPE SYNTAX Integer32(0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This is the TEI(Terminal Endpoint Identifier) of a specific DLC. " ::= { vismLapdDlcEntry 3 } vismLapdDlcLinkState OBJECT-TYPE SYNTAX INTEGER { up (1), down (2), unknown(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicate the linking state on a given DLC. " ::= { vismLapdDlcEntry 4 } -- ***************************************************************** -- LAPD Trunk group notification -- ***************************************************************** vismLapdTrunkNotificationPrefix OBJECT IDENTIFIER ::= { ciscoWanLapdTrunkMIB 2 } vismLapdTrunkNotifications OBJECT IDENTIFIER ::= { vismLapdTrunkNotificationPrefix 0 } -- ********************************************************************** -- Conformance -- ********************************************************************** -- -- conformance information -- vismLapdTrunkMIBConformance OBJECT IDENTIFIER ::= { ciscoWanLapdTrunkMIB 3 } vismLapdTrunkMIBCompliances OBJECT IDENTIFIER ::= { vismLapdTrunkMIBConformance 1 } vismLapdTrunkMIBGroups OBJECT IDENTIFIER ::= { vismLapdTrunkMIBConformance 2 } -- -- Conformance and compliance statements statements -- vismLapdTrunkMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION " The complaince statement for LAPD Trunk group which implements vismLapdTrunkGrp MIB." MODULE -- this module MANDATORY-GROUPS { vismLapdTrunkGroup, ciscoVismLapdGroup, ciscoVismLapdStatsGroup, ciscoVismLapdDlcTable } OBJECT vismLapdRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6) } MIN-ACCESS read-create DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported. " ::= { vismLapdTrunkMIBCompliances 1 } -- -- units of conformance -- -- MIB Groups -- vismLapdTrunkGroup OBJECT-GROUP OBJECTS { vismLapdTrunkState, vismLapdTrunkRudpIndex, vismLapdTrunkRowStatus } STATUS current DESCRIPTION "This group contains objects related to configuration of LAPD Trunk connections over RUDP. " ::= { vismLapdTrunkMIBGroups 1 } ciscoVismLapdGroup OBJECT-GROUP OBJECTS { vismLapdIndex, vismLapdAppType, vismLapdWinSize, vismLapdN200, vismLapdT200, vismLapdT203, vismLapdType, vismLapdRowStatus, vismLapdSide, vismLapdTrunkType } STATUS current DESCRIPTION "The collection of objects which are used to represent VISM LAPD information." ::= { vismLapdTrunkMIBGroups 2 } ciscoVismLapdStatsGroup OBJECT-GROUP OBJECTS { vismLapdStatsIndex, vismLapdRxInfoFrames, vismLapdTxInfoFrames, vismLapdRxReadyFrames, vismLapdTxReadyFrames, vismLapdRxNotReadyFrames, vismLapdTxNotReadyFrames, vismLapdRxSABMFrames, vismLapdTxSABMFrames, vismLapdRxDisconFrames, vismLapdTxDisconFrames, vismLapdRxUAFrames, vismLapdTxUAFrames, vismLapdRxDiscModeFrames, vismLapdTxDiscModeFrames, vismLapdRxFrmRejectFrames, vismLapdTxFrmRejectFrames, vismLapdRxExchIdFrames, vismLapdTxExchIdFrames, vismLapdRxUnumInfoFrames, vismLapdTxUnumInfoFrames, vismLapdRxRejectFrames, vismLapdTxRejectFrames, vismLapdRxInvalidFrames } STATUS current DESCRIPTION "The collection of objects which are used to represent VISM LAPD Statistics information." ::= { vismLapdTrunkMIBGroups 3 } ciscoVismLapdDlcTable OBJECT-GROUP OBJECTS { vismLapdDlcIndex, vismLapdDlcSapi, vismLapdDlcTei, vismLapdDlcLinkState } STATUS current DESCRIPTION "The collection of objects which are used to represent VISM LAPD link State of different DLCs on a LAPD channel." ::= { vismLapdTrunkMIBGroups 4 } END