-- ***************************************************************** -- -- February 2009. Frank Fang -- -- Copyright (c) 2007-2013 by cisco Systems Inc. -- All rights reserved. -- ***************************************************************** CISCO-WAN-3G-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Integer32, Unsigned32, Counter64, Counter32, Gauge32 FROM SNMPv2-SMI MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP FROM SNMPv2-CONF SnmpAdminString FROM SNMP-FRAMEWORK-MIB entPhysicalName, entPhysicalIndex FROM ENTITY-MIB ifIndex FROM IF-MIB InetAddress, InetAddressType FROM INET-ADDRESS-MIB RowStatus, DisplayString, TEXTUAL-CONVENTION, TruthValue FROM SNMPv2-TC ciscoMgmt FROM CISCO-SMI; ciscoWan3gMIB MODULE-IDENTITY LAST-UPDATED "201308120000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-3g@cisco.com cs-4g@cisco.com" DESCRIPTION "This MIB module provides network management support for Cisco cellular 3G and 4G LTE WAN products. *** ABBREVIATIONS, ACRONYMS, AND SYMBOLS *** 1xRTT - 1 times Radio Transmission Technology. 3G - Third generation of mobile phones standards and technologies. 4G - Fourth generation of mobile phones standards and technologies Azimuth - Angle of rotation of a satellite Dish. BER - Bit Error Ratio. BS - Base Station. CDMA - Code Division Multiple Access. dB - decibel. dBm - power ratio in decibels (dB) of the measured power referenced to one milliwatt (mW). CnS - Control and Status proprietary protocol for managing the control and status of the modem. Ec/Io - ratio of received pilot energy, Ec, to total received energy or the total power spectral density, Io. EDGE - Enhanced Data rate for GSM Evolution. EPS - Evolved Packet System EVDO - EVolution Data Optimized. FDD - Frequency Division Duplexing GPRS - General Packet Radio Service. GSM - Global System for Mobile communications. GPS - Global Positioning System. HSDPA - High Speed Downlink Packet Access. HSPA - High Speed Packet Access. HSUPA - High Speed Uplink Packet Access. LBS - Location Based Service. LTE - Long Term Evolution MT - Mobile Termination. PDP - Packet Data Protocol. PLMN - Public Land Mobile Network. QoS - Quality of Service. RSSI - Received Signal Strength Indication. SDU - Service Data Unit. SER - SDU Error Ratio. SIM - Subscriber Identity Module. SMS - Short Messaging Service. SNR - Signal to Noise Ratio. TDD - Time Division Duplexing UMTS - Universal Mobile Telecommunication System. WCDMA - Wideband Code Division Multiple Access." REVISION "201308120000Z" DESCRIPTION "Added new notifications c3gModemTemperOnsetRecoveryNotif, c3gModemTemperAbateRecoveryNotif." REVISION "201207250000Z" DESCRIPTION "Modified Description of the ciscoWan3gMIB module. Modified the description of c3gWanCommonTable, c3gWanLbsCommonTable, c3gSmsCommonTable and all its objects to emphazise that it is technology independent. Added enumerated value lte to objects C3gServiceCapability, c3gCurrentIdleDigitalMode, c3gGsmPacketService. Modified the descriptions of c3gGsmIdentityTable, and all its objects to emphazise that these objects are applicable to both 3G and 4G-LTE Technology. Added new object c3gGpsState to the table c3gWanCommonTable. Added enumerated value lteBand for c3gGsmCurrentBand. Modified ciscoWan3gMIBGsmObjectGroup, ciscoWan3gMIBSmsObjectGroup, ciscoWan3gMIBLbsObjectGroup, ciscoWan3gMIBGsmObjectGroup description in Module ciscoWan3gMIBCompliance, ciscoWan3gMIBCompliance1. Added c3gGpsState to the group ciscoWan3gMIBCommonObjectGroup." REVISION "201207100000Z" DESCRIPTION "Added enumerated values rate56kbps(12) to rate8dot4mbps(18) for C3gUmtsQosLinkBitRate." REVISION "201008110000Z" DESCRIPTION "Fixed spelling errors." REVISION "201008040000Z" DESCRIPTION "Added c3gWanLbs and c3gWanSms. Added ciscoWan3gMIBSmsObjectGroup and ciscoWan3gMIBSmsObjectGroup. Deprecated ciscoWan3gMIBCompliance and replaced by ciscoWan3gMIBCompliance1." REVISION "200902050000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 661 } C3gServiceCapability ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "3G service capability: oneXRtt(0) - 1xRTT evDoRel0(1) - EVDO Revision 0 evDoRelA(2) - EVDO Revision A evDoRelB(3) - EVDO Revision B gprs(4) - GPRS edge(5) - EDGE umtsWcdma(6) - UMTS/WCDMA hsdpa(7) - HSDPA hsupa(8) - HSUPA hspa(9) - HSPA hspaPlus(10) - HSPA Plus lteTdd(11) - LTE TDD lteFdd (12) - LTE FDD" SYNTAX BITS { oneXRtt(0), evDoRel0(1), evDoRelA(2), evDoRelB(3), gprs(4), edge(5), umtsWcdma(6), hsdpa(7), hsupa(8), hspa(9), hspaPlus(10), lteTdd(11), lteFdd(12) } C3gRssi ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Generic RSSI range." SYNTAX Integer32 (-150..0) C3gEcIo ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Generic EcIo range." SYNTAX Integer32 (-150..0) C3gTemperature ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Generic temperature range." SYNTAX Integer32 (-50..100) C3gPdpType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Generic PDP type." SYNTAX INTEGER { unknown(1), ipV4(2), ppp(3), ipV6(4), ipV4V6(5) } C3gUmtsQosTrafficClass ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "UMTS QoS traffic classes: subscription(1) - based on user's subscription conversational(2) - conversational streaming(3) - streaming interactive(4) - interactive background(5) - background" SYNTAX INTEGER { subscription(1), conversational(2), streaming(3), interactive(4), background(5) } C3gUmtsQosLinkBitRate ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "UMTS QoS link bit rate: subscription(1) - based on user's subscription rate16kbps(2) - 16 Kbps rate32kbps(3) - 32 Kbps rate64kbps(4) - 64 Kbps rate128kbps(5) - 128 Kbps rate256kbps(6) - 256 Kbps rate384kbps(7) - 384 Kbps rate1dot8mbps(8) - 1.8 Mbps rate3dot6mbps(9) - 3.6 Mbps rate7dot2mbps(10) - 7.2 Mbps rate14dot4mbps(11) - 14.4 Mbps rate56kbps(12) - 56 Kbps rate1dot15mbps(13) - 1.15 Mbps rate1dot6mbps(14) - 1.6 Mbps rate2dot1mbps(15) - 2.1 Mbps rate2dot8mbps(16) - 2.8 Mbps rate4dot2mbps(17) - 4.2 Mbps rate8dot4mbps(18) - 8.4 Mbps" SYNTAX INTEGER { subscription(1), rate16kbps(2), rate32kbps(3), rate64kbps(4), rate128kbps(5), rate256kbps(6), rate384kbps(7), rate1dot8mbps(8), rate3dot6mbps(9), rate7dot2mbps(10), rate14dot4mbps(11), rate56kbps(12), rate1dot15mbps(13), rate1dot6mbps(14), rate2dot1mbps(15), rate2dot8mbps(16), rate4dot2mbps(17), rate8dot4mbps(18) } C3gUmtsQosOrder ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "UMTS QoS delivery order: subscription(1) - based on user's subscription withDeliverOrder(2) - with delivery order withoutDeliverOrder(3) - without delivery order" SYNTAX INTEGER { subscription(1), withDeliverOrder(2), withoutDeliverOrder(3) } C3gUmtsQosErroneousSdu ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "UMTS QoS Delivery of Erroneous Service Data Unit(SDU): subscription(1) - based on user's subscription noDetect(2) - no detect errSduDeliver(3) - erroneous SDUs are delivered errSduNotDeliver(4) - erroneous SDUs are not delivered" SYNTAX INTEGER { subscription(1), noDetect(2), errSduDeliver(3), errSduNotDeliver(4) } C3gUmtsQosSer ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "UMTS QoS SDU error ratio: subscription(1) - based on user's subscription oneExpMinus2(2) - 1E-2 sevenExpMinus3(3) - 7E-3 oneExpMinus3(4) - 1E-3 oneExpMinus4(5) - 1E-4 oneExpMinus5(6) - 1E-5 oneExpMinus6(7) - 1E-6 oneExpMinus1(8) - 1E-1" SYNTAX INTEGER { subscription(1), oneExpMinus2(2), sevenExpMinus3(3), oneExpMinus3(4), oneExpMinus4(5), oneExpMinus5(6), oneExpMinus6(7), oneExpMinus1(8) } C3gUmtsQosBer ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "UMTS QoS residual bit error ratio (BER): subscription(1) - based on user's subscription fiveExpMinus2(2) - 5E-2 oneExpMinus2(3) - 1E-2 fiveExpMinus3(4) - 5E-3 fourExpMinus3(5) - 4E-3 oneExpMinus3(6) - 1E-3 oneExpMinus4(7) - 1E-4 oneExpMinus5(8) - 1E-5 oneExpMinus6(9) - 1E-6 sixExpMinus8(10) - 6E-8" SYNTAX INTEGER { subscription(1), fiveExpMinus2(2), oneExpMinus2(3), fiveExpMinus3(4), fourExpMinus3(5), oneExpMinus3(6), oneExpMinus4(7), oneExpMinus5(8), oneExpMinus6(9), sixExpMinus8(10) } C3gUmtsQosPriority ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "UMTS QoS traffic handling priority: subscription(1) - based on user's subscription level1(2) - priority level 1 level2(3) - priority level 2 level3(4) - priority level 3" SYNTAX INTEGER { subscription(1), level1(2), level2(3), level3(4) } C3gUmtsQosSrcStatDescriptor ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "UMTS QoS source statistics descriptor: unknown(1) - unknown speech(2) - speech" SYNTAX INTEGER { unknown(1), speech(2) } C3gUmtsQosSignalIndication ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "UMTS QoS signalling indication: notOptimized(1) - not optimized for signalling traffic optimized(2) - optimized for signalling traffic" SYNTAX INTEGER { notOptimized(1), optimized(2) } C3gGprsQosPrecedence ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "GPRS QoS precedence: subscription(1) - based on user's subscription highPriority(2) - high priority normalPriority(3) - normal priority lowPriority(4) - low priority" SYNTAX INTEGER { subscription(1), highPriority(2), normalPriority(3), lowPriority(4) } C3gGprsQosDelay ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "GPRS QoS delay classes: subscription(1) - based on user's subscription delayClass1(2) - delay class 1 delayClass2(3) - delay class 2 delayClass3(4) - delay class 3 delayClass4(5) - delay class 4" SYNTAX INTEGER { subscription(1), delayClass1(2), delayClass2(3), delayClass3(4), delayClass4(5) } C3gGprsQosReliability ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "GPRS QoS reliability: subscription(1) - based on user's subscription ackGtpLlcRlcProtData(2) - acknowledged GTP, LLC, and RLC; protected data unAckGtpAckLlcRlcProtData(3) - unacknowledged GTP, acknowledged LLC and RLC; protected data unAckGtpLlcAckRlcProtData(4) - unacknowledged GTP and LLC, acknowledged RLC; protected data unAckGtpLlcRlcProtData(5) - unacknowledged GTP, LLC, and RLC; protected data unAckGtpLlcRlcUnProtData(6) - unacknowledged GTP, LLC, and RLC; unprotected data" SYNTAX INTEGER { subscription(1), ackGtpLlcRlcProtData(2), unAckGtpAckLlcRlcProtData(3), unAckGtpLlcAckRlcProtData(4), unAckGtpLlcRlcProtData(5), unAckGtpLlcRlcUnProtData(6) } C3gGprsQosPeakRate ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "GPRS QoS peak rate: subscription(1) - based on user's subscription upTo1kops(2) - up to 1000 octet/second upTo2kops(3) - up to 2000 octet/second upTo4kops(4) - up to 4000 octet/second upTo8kops(5) - up to 8000 octet/second upTo16kops(6) - up to 16000 octet/second upTo32kops(7) - up to 32000 octet/second upTo64kops(8) - up to 64000 octet/second upTo128kops(9) - up to 128000 octet/second upTo256kops(10) - up to 256000 octet/second" SYNTAX INTEGER { subscription(1), upTo1kops(2), upTo2kops(3), upTo4kops(4), upTo8kops(5), upTo16kops(6), upTo32kops(7), upTo64kops(8), upTo128kops(9), upTo256kops(10) } C3gGprsQosMeanRate ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "GPRS QoS mean rate: subscription(1) - based on user's subscription rate100(2) - 100 octet/hour rate200(3) - 200 octet/hour rate500(4) - 500 octet/hour rate1k(5) - 1000 octet/hour rate2k(6) - 2000 octet/hour rate5k(7) - 5000 octet/hour rate10k(8) - 10000 octet/hour rate20k(9) - 20000 octet/hour rate50k(10) - 50000 octet/hour rate100k(11) - 100000 octet/hour rate200k(12) - 200000 octet/hour rate500k(13) - 500000 octet/hour rate1m(14) - 1000000 octet/hour rate2m(15) - 2000000 octet/hour rate5m(16) - 5000000 octet/hour rate10m(17) - 10000000 octet/hour rate20m(18) - 20000000 octet/hour rate50m(19) - 50000000 octet/hour resv1(20) - reserved 1 (for future use) resv2(21) - reserved 2 (for future use) resv3(22) - reserved 3 (for future use) resv4(23) - reserved 4 (for future use) resv5(24) - reserved 5 (for future use) resv6(25) - reserved 6 (for future use) resv7(26) - reserved 7 (for future use) resv8(27) - reserved 8 (for future use) resv9(28) - reserved 9 (for future use) resv10(29) - reserved 10 (for future use) resv11(30) - reserved 11 (for future use) resv12(31) - reserved 12 (for future use) bestEffort(32) - best effort" SYNTAX INTEGER { subscription(1), rate100(2), rate200(3), rate500(4), rate1k(5), rate2k(6), rate5k(7), rate10k(8), rate20k(9), rate50k(10), rate100k(11), rate200k(12), rate500k(13), rate1m(14), rate2m(15), rate5m(16), rate10m(17), rate20m(18), rate50m(19), resv1(20), resv2(21), resv3(22), resv4(23), resv5(24), resv6(25), resv7(26), resv8(27), resv9(28), resv10(29), resv11(30), resv12(31), bestEffort(32) } -- Textual Conventions definition will be defined before this objects ciscoWan3gMIBNotifs OBJECT IDENTIFIER ::= { ciscoWan3gMIB 0 } ciscoWan3gMIBObjects OBJECT IDENTIFIER ::= { ciscoWan3gMIB 1 } ciscoWan3gMIBConform OBJECT IDENTIFIER ::= { ciscoWan3gMIB 2 } c3gWanCommonTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gWanCommonEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Cellular common objects table which is technology independent." ::= { ciscoWan3gMIBObjects 1 } c3gWanCommonEntry OBJECT-TYPE SYNTAX C3gWanCommonEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the c3gWanCommonTable." INDEX { entPhysicalIndex } ::= { c3gWanCommonTable 1 } C3gWanCommonEntry ::= SEQUENCE { c3gStandard INTEGER, c3gCapability C3gServiceCapability, c3gModemState INTEGER, c3gPreviousServiceType C3gServiceCapability, c3gCurrentServiceType C3gServiceCapability, c3gRoamingStatus INTEGER, c3gCurrentSystemTime DisplayString, c3gConnectionStatus INTEGER, c3gNotifRadioService C3gServiceCapability, c3gNotifRssi C3gRssi, c3gNotifEcIo C3gEcIo, c3gModemTemperature C3gTemperature, c3gRssiOnsetNotifThreshold C3gRssi, c3gRssiAbateNotifThreshold C3gRssi, c3gEcIoOnsetNotifThreshold C3gEcIo, c3gEcIoAbateNotifThreshold C3gEcIo, c3gModemTemperOnsetNotifThreshold C3gTemperature, c3gModemTemperAbateNotifThreshold C3gTemperature, c3gModemReset INTEGER, c3gModemUpNotifEnabled TruthValue, c3gModemDownNotifEnabled TruthValue, c3gServiceChangedNotifEnabled TruthValue, c3gNetworkChangedNotifEnabled TruthValue, c3gConnectionStatusChangedNotifFlag BITS, c3gRssiOnsetNotifFlag C3gServiceCapability, c3gRssiAbateNotifFlag C3gServiceCapability, c3gEcIoOnsetNotifFlag C3gServiceCapability, c3gEcIoAbateNotifFlag C3gServiceCapability, c3gModemTemperOnsetNotifEnabled TruthValue, c3gModemTemperAbateNotifEnabled TruthValue, c3gGpsState TruthValue } c3gStandard OBJECT-TYPE SYNTAX INTEGER { cdma(1), gsm(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Cellular Standard: GSM (Global System for Mobile communications, 3GPP), CDMA (Code Division Multiple Access, 3GPP-2). GSM standard also include 4G-LTE technology mode" ::= { c3gWanCommonEntry 1 } c3gCapability OBJECT-TYPE SYNTAX C3gServiceCapability MAX-ACCESS read-only STATUS current DESCRIPTION "Cellular service capability. It currently includes the 2G, 3G and 4G-LTE standard." ::= { c3gWanCommonEntry 2 } c3gModemState OBJECT-TYPE SYNTAX INTEGER { unknown(1), up(2), down(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Cellular modem state, up(2) indicates modem can be detected and down(3) indicates modem can not be detected." DEFVAL { down } ::= { c3gWanCommonEntry 3 } c3gPreviousServiceType OBJECT-TYPE SYNTAX C3gServiceCapability MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the previous service type when service type changes." ::= { c3gWanCommonEntry 4 } c3gCurrentServiceType OBJECT-TYPE SYNTAX C3gServiceCapability MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the current service type when service type changes." ::= { c3gWanCommonEntry 5 } c3gRoamingStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), roaming(2), home(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Cellular current roaming status." ::= { c3gWanCommonEntry 6 } c3gCurrentSystemTime OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Cellular current system time received from base station." ::= { c3gWanCommonEntry 7 } c3gConnectionStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), error(2), connecting(3), dormant(4), connected(5), disconnected(6), idle(7), active(8), inactive(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the current connection status." ::= { c3gWanCommonEntry 8 } c3gNotifRadioService OBJECT-TYPE SYNTAX C3gServiceCapability MAX-ACCESS read-only STATUS current DESCRIPTION "This object is used as one of the var-bind object when notification for RSSI or Ec/Io is generated. This object indicates which service generates the notification." ::= { c3gWanCommonEntry 9 } c3gNotifRssi OBJECT-TYPE SYNTAX C3gRssi MAX-ACCESS read-only STATUS current DESCRIPTION "This object is used as one of the var-bind object when notification for RSSI is generated. The relevant RSSI will be copied into c3gNotifRssi which corresponds to the service indicated in c3gNotifRadioService object. This object will reflect the value of one of the following objects: c3gCurrent1xRttRssi, c3gCurrentEvDoRssi and c3gCurrentGsmRssi. User should not use this object to get the current RSSI value as this object is used to indicate the RSSI value that triggers c3gRssiOnsetNotif or c3gRssiAbateNotif notification." ::= { c3gWanCommonEntry 10 } c3gNotifEcIo OBJECT-TYPE SYNTAX C3gEcIo MAX-ACCESS read-only STATUS current DESCRIPTION "This object is used as one of the var-bind object when notification for Ec/Io is generated. The relevant Ec/Io will be copied into c3gNotifEcIo which corresponds to the service indicated in c3gNotifRadioService object. This object will reflect the value of one of the following objects: c3gCurrent1xRttEcIo, c3gCurrentEvDoEcIo and c3gCurrentGsmEcIo. User should not use this object to get the current Ec/Io value as this object is used to indicate the Ec/Io value that triggers c3gEcIoOnsetNotif or c3gEcIoAbateNotif notification." ::= { c3gWanCommonEntry 11 } c3gModemTemperature OBJECT-TYPE SYNTAX C3gTemperature UNITS "degrees Celsius" MAX-ACCESS read-only STATUS current DESCRIPTION "The modem temperature." ::= { c3gWanCommonEntry 12 } c3gRssiOnsetNotifThreshold OBJECT-TYPE SYNTAX C3gRssi UNITS "dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "The RSSI onset threshold value. If RSSI goes below the threshold and the service bit in c3gRssiOnsetNotifFlag is set, the c3gRssiOnsetNotif notification for that service will be sent. The absolute value of c3gRssiAbateNotifThreshold should be less than or equal to the absolute value of c3gRssiOnsetNotifThreshold (|c3gRssiAbateNotifThreshold| <= |c3gRssiOnsetNotifThreshold|). e.g. setting c3gRssiAbateNotifThreshold to -115 dBm and then setting c3gRssiOnsetNotifThreshold to -110 dBm is not allowed and will be rejected." DEFVAL { -150 } ::= { c3gWanCommonEntry 13 } c3gRssiAbateNotifThreshold OBJECT-TYPE SYNTAX C3gRssi UNITS "dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "The RSSI abate threshold value. If RSSI goes above the threshold and the service bit in c3gRssiAbateNotifFlag is set, the c3gRssiAbateNotif notification for that service will be sent. The absolute value of c3gRssiAbateNotifThreshold should be less than or equal to the absolute value of c3gRssiOnsetNotifThreshold (|c3gRssiAbateNotifThreshold| <= |c3gRssiOnsetNotifThreshold|). e.g. setting c3gRssiAbateNotifThreshold to -115 dBm and then setting c3gRssiOnsetNotifThreshold to -110 dBm is not allowed and will be rejected." DEFVAL { 0 } ::= { c3gWanCommonEntry 14 } c3gEcIoOnsetNotifThreshold OBJECT-TYPE SYNTAX C3gEcIo UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "The EcIo onset threshold value. If EcIo goes below the threshold and the service bit in c3gEcIoOnsetNotifFlag is set, the c3gEcIoOnsetNotif notification for that service will be sent. The absolute value of c3gEcIoAbateNotifThreshold should be less than or equal to the absolute value of c3gEcIoOnsetNotifThreshold (|c3gEcIoAbateNotifThreshold| <= |c3gEcIoOnsetNotifThreshold|). e.g. setting c3gEcIoAbateNotifThreshold to -15 dB and then setting c3gEcIoOnsetNotifThreshold to -10 dB is not allowed and will be rejected." DEFVAL { -150 } ::= { c3gWanCommonEntry 15 } c3gEcIoAbateNotifThreshold OBJECT-TYPE SYNTAX C3gEcIo UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "The threshold value that if EcIo goes above the threshold and the service bit in c3gEcIoAbateNotifFlag is set, the c3gEcIoAbateNotif notification for that service will be sent. The absolute value of c3gEcIoAbateNotifThreshold should be less than or equal to the absolute value of c3gEcIoOnsetNotifThreshold (|c3gEcIoAbateNotifThreshold| <= |c3gEcIoOnsetNotifThreshold|). e.g. setting c3gEcIoOnsetNotifThreshold to -15 dB and then setting c3gEcIoAbateNotifThreshold to -10 dB is not allowed and will be rejected." DEFVAL { 0 } ::= { c3gWanCommonEntry 16 } c3gModemTemperOnsetNotifThreshold OBJECT-TYPE SYNTAX C3gTemperature UNITS "degrees Celsius" MAX-ACCESS read-write STATUS current DESCRIPTION "The modem temperature onset threshold value. If modem temperature goes above the threshold and the value of c3gModemTemperOnsetNotifEnabled is 'true', the c3gModemTemperOnsetNotif notification will be sent. The value of c3gModemTemperAbateNotifThreshold should be less than or equal to the value of c3gModemTemperOnsetNotifThreshold. e.g. setting c3gModemTemperAbateNotifThreshold to 50 degree Celsius and then setting c3gModemTemperOnsetNotifThreshold to 40 degree Celsius is not allowed and will be rejected." DEFVAL { 100 } ::= { c3gWanCommonEntry 17 } c3gModemTemperAbateNotifThreshold OBJECT-TYPE SYNTAX C3gTemperature UNITS "degrees Celsius" MAX-ACCESS read-write STATUS current DESCRIPTION "The modem temperature abate threshold value. If modem temperature goes below the threshold and the value of c3gModemTemperAbateNotifEnabled is 'true', the c3gModemTemperAbateNotif notification will be sent. The value of c3gModemTemperAbateNotifThreshold should be less than or equal to the value of c3gModemTemperOnsetNotifThreshold. e.g. setting c3gModemTemperAbateNotifThreshold to 50 degree Celsius and then setting c3gModemTemperOnsetNotifThreshold to 40 degree Celsius is not allowed and will be rejected." DEFVAL { -50 } ::= { c3gWanCommonEntry 18 } c3gModemReset OBJECT-TYPE SYNTAX INTEGER { reset(1), powerCycle(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to reset or power-cycle the modem." ::= { c3gWanCommonEntry 19 } c3gModemUpNotifEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to enable/disable the generation of modem up notification c3gModemUpNotif." DEFVAL { false } ::= { c3gWanCommonEntry 20 } c3gModemDownNotifEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to enable/disable the generation of modem down notification c3gModemDownNotif." DEFVAL { false } ::= { c3gWanCommonEntry 21 } c3gServiceChangedNotifEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to enable/disable the generation of service changed notification c3gServiceChangedNotif." DEFVAL { false } ::= { c3gWanCommonEntry 22 } c3gNetworkChangedNotifEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to enable/disable the generation of network changed notification c3gNetworkChangedNotif." DEFVAL { false } ::= { c3gWanCommonEntry 23 } c3gConnectionStatusChangedNotifFlag OBJECT-TYPE SYNTAX BITS { unknown(0), error(1), connecting(2), dormant(3), connected(4), disconnected(5), idle(6), active(7), inactive(8) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is the flag bitmap to control the generation of notification c3gConnectionStatusChangedNotif. e.g. setting bit 0 (error(0)) to 1 and bit 4 (disconnected(4)) to 1 will cause the notification c3gConnectionStatusChangedNotif to be generated when object c3gConnetionStatus changes the status to error or disconnected. The default value of this object is '00'H." ::= { c3gWanCommonEntry 24 } c3gRssiOnsetNotifFlag OBJECT-TYPE SYNTAX C3gServiceCapability MAX-ACCESS read-write STATUS current DESCRIPTION "This object is the flag bitmap to control the generation of notification c3gRssiOnsetNotif. Each bit represents a service as defined in C3gServiceCapability, set the bit value to 1 to enable (and 0 to disable) the generation of notification c3gRssiOnsetNotif for that service. The default value of this object is all bits are 0." ::= { c3gWanCommonEntry 25 } c3gRssiAbateNotifFlag OBJECT-TYPE SYNTAX C3gServiceCapability MAX-ACCESS read-write STATUS current DESCRIPTION "This object is the flag bitmap to control the generation of notification c3gRssiAbateNotif. Each bit represents a service as defined in C3gServiceCapability, set the bit value to 1 to enable (and 0 to disable) the generation of notification c3gRssiAbateNotif for that service. The default value of this object is all bits are 0." ::= { c3gWanCommonEntry 26 } c3gEcIoOnsetNotifFlag OBJECT-TYPE SYNTAX C3gServiceCapability MAX-ACCESS read-write STATUS current DESCRIPTION "This object is the flag bitmap to control the generation of notification c3gEcIoOnsetNotif. Each bit represents a service as defined in C3gServiceCapability, set the bit value to 1 to enable (and 0 to disable) the generation of notification c3gEcIoOnsetNotif for that service. The default value of this object is all bits are 0." ::= { c3gWanCommonEntry 27 } c3gEcIoAbateNotifFlag OBJECT-TYPE SYNTAX C3gServiceCapability MAX-ACCESS read-write STATUS current DESCRIPTION "This object is the flag bitmap to control the generation of notification c3gEcIoAbateNotif. Each bit represents a service as defined in C3gServiceCapability, set the bit value to 1 to enable (and 0 to disable) the generation of notification c3gEcIoAbateNotif for that service. The default value of this object is all bits are 0." ::= { c3gWanCommonEntry 28 } c3gModemTemperOnsetNotifEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to enable/disable the generation of c3gModemTemperOnsetNotif notification." DEFVAL { false } ::= { c3gWanCommonEntry 29 } c3gModemTemperAbateNotifEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to enable/disable the generation of c3gModemTemperAbateNotif notification." DEFVAL { false } ::= { c3gWanCommonEntry 30 } c3gGpsState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to determine or enable/disable the GPS state." DEFVAL { false } ::= { c3gWanCommonEntry 31 } c3gWanCdma OBJECT IDENTIFIER ::= { ciscoWan3gMIBObjects 2 } c3gWanGsm OBJECT IDENTIFIER ::= { ciscoWan3gMIBObjects 3 } c3gWanLbs OBJECT IDENTIFIER ::= { ciscoWan3gMIBObjects 4 } c3gWanSmsCommon OBJECT IDENTIFIER ::= { ciscoWan3gMIBObjects 5 } c3gCdmaSessionTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gCdmaSessionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes wireless session (link) created when a modem connects to a particular cellular network. One or more logical calls can be placed over wireless session(link). These logical calls are represented in the c3gCdmaConnectionTable." ::= { c3gWanCdma 1 } c3gCdmaSessionEntry OBJECT-TYPE SYNTAX C3gCdmaSessionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the c3gCdmaSessionTable." INDEX { entPhysicalIndex } ::= { c3gCdmaSessionTable 1 } C3gCdmaSessionEntry ::= SEQUENCE { c3gCdmaTotalCallDuration Counter64, c3gCdmaTotalTransmitted Counter64, c3gCdmaTotalReceived Counter64, c3gHdrDdtmPreference INTEGER } c3gCdmaTotalCallDuration OBJECT-TYPE SYNTAX Counter64 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Total duration of all calls." ::= { c3gCdmaSessionEntry 1 } c3gCdmaTotalTransmitted OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Total data transmitted for all calls. It is the total amount of data transmitted by modem, not to be confused with the number of bytes transmitted through the interface." ::= { c3gCdmaSessionEntry 2 } c3gCdmaTotalReceived OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Total data received for all calls. It is the total amount of data received by modem, not to be confused with the number of bytes received from the interface." ::= { c3gCdmaSessionEntry 3 } c3gHdrDdtmPreference OBJECT-TYPE SYNTAX INTEGER { unknown(1), off(2), on(3), noChange(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "HDR Data Dedicated Transmission Mode (DDTM) preference: unknown(1) - DDTM preference is unknown off(2) - DDTM preference set to OFF on(3) - DDTM preference set to ON noChange(4) - DDTM preference is no change" DEFVAL { unknown } ::= { c3gCdmaSessionEntry 4 } c3gCdmaConnectionTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gCdmaConnectionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Cellular 3G CDMA connection table. This table describes logical connections/calls over wireless link, the wireless link is described in c3gCdmaSessionTable." ::= { c3gWanCdma 2 } c3gCdmaConnectionEntry OBJECT-TYPE SYNTAX C3gCdmaConnectionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the c3gCdmaConnectionTable." INDEX { ifIndex } ::= { c3gCdmaConnectionTable 1 } C3gCdmaConnectionEntry ::= SEQUENCE { c3gOutgoingCallNumber DisplayString, c3gHdrAtState INTEGER, c3gHdrSessionState INTEGER, c3gUati DisplayString, c3gColorCode Unsigned32, c3gRati Unsigned32, c3gHdrSessionDuration Unsigned32, c3gHdrSessionStart Unsigned32, c3gHdrSessionEnd Unsigned32, c3gAuthStatus INTEGER, c3gHdrDrc Unsigned32, c3gHdrDrcCover Unsigned32, c3gHdrRri INTEGER, c3gMobileIpErrorCode Integer32, c3gCdmaCurrentTransmitted Counter64, c3gCdmaCurrentReceived Counter64, c3gCdmaCurrentCallStatus INTEGER, c3gCdmaCurrentCallDuration Unsigned32, c3gCdmaCurrentCallType INTEGER, c3gCdmaLastCallDisconnReason INTEGER, c3gCdmaLastConnError INTEGER } c3gOutgoingCallNumber OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Phone number of outgoing call." ::= { c3gCdmaConnectionEntry 1 } c3gHdrAtState OBJECT-TYPE SYNTAX INTEGER { unknown(1), inactive(2), acquisition(3), sync(4), idle(5), access(6), connected(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "High Data Rate (HDR) Access Terminal (AT) state." DEFVAL { unknown } ::= { c3gCdmaConnectionEntry 2 } c3gHdrSessionState OBJECT-TYPE SYNTAX INTEGER { unknown(1), open(2), close(3), addressManagementProtocolSetup(4), atInitiated(5), anInitiated(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "High Data Rate (HDR) session state." ::= { c3gCdmaConnectionEntry 3 } c3gUati OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Unicast Access Terminal Identifier (UATI), AT seeking access to the 1 times EV-DO system receives a UATI allocated from the system after setting up a radio traffic channel with a base station." ::= { c3gCdmaConnectionEntry 4 } c3gColorCode OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Color code. A sync channel may be used by the base station to communicate administrative information to a mobile station. For example, a base station may transmit a base station ID to a user, a color code and administrative information identifying system status." ::= { c3gCdmaConnectionEntry 5 } c3gRati OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Random Access Terminal Identifier (RATI). AT transmits a UATI request message to the ANC using the RATI to make a UATI allocation request." ::= { c3gCdmaConnectionEntry 6 } c3gHdrSessionDuration OBJECT-TYPE SYNTAX Unsigned32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "HDR connection session duration. It is the duration between c3gHdrSessionStart and c3gHdrSessionEnd." DEFVAL { 0 } ::= { c3gCdmaConnectionEntry 7 } c3gHdrSessionStart OBJECT-TYPE SYNTAX Unsigned32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "HDR connection session starting time." DEFVAL { 0 } ::= { c3gCdmaConnectionEntry 8 } c3gHdrSessionEnd OBJECT-TYPE SYNTAX Unsigned32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "HDR connection session ending time." DEFVAL { 0 } ::= { c3gCdmaConnectionEntry 9 } c3gAuthStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), notAuthenticated(2), authenticated(3), failed(4), authenticationDisabled(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Connection authentication status: unknown(1) - authentication status is unknown notAuthenticated(2) - not yet authenticated. authenticated(3) - authenticated. failed(4) - authentication failed. authenticationDisabled(5) - authentication disabled" DEFVAL { unknown } ::= { c3gCdmaConnectionEntry 10 } c3gHdrDrc OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "High Data Rate (HDR) Data Rate Control (DRC). AT provides requests for data transmissions by sending a Data Rate Control, DRC, message via a specific channel referred to as the DRC channel." DEFVAL { 0 } ::= { c3gCdmaConnectionEntry 11 } c3gHdrDrcCover OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "HDR DRC cover. The DRC cover is a coding applied to identify the sector from which the data is to be transmitted. In one embodiment, the DRC cover is a Walsh code applied to the DRC value, wherein a unique code corresponds to each sector in the Active Set of the AT." DEFVAL { 0 } ::= { c3gCdmaConnectionEntry 12 } c3gHdrRri OBJECT-TYPE SYNTAX INTEGER { unknown(1), pilotOnly(2), rri9dot6kbps(3), rri19dot2kbps(4), rri38dot4kbps(5), rri76dot8kbps(6), rri153dot6kbps(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "HDR Rate Request Indicator (RRI). RRI provides the structure of a frame currently being transmitted when frames are transmitted at different rates. Services at different rates are reliably provided by the RRI: unknown(1) - RRI unknown pilotOnly(2) - pilot channel only rri9dot6kbps(3) - RRI is 9.6 Kbit/s rri19dot2kbps(4) - RRI is 19.2 Kbit/s rri38dot4kbps(5) - RRI is 38.4 Kbit/s rri76dot8kbps(6) - RRI is 76.8 Kbit/s rri153dot6kbps(7) - RRI is 153.6 Kbit/s" DEFVAL { unknown } ::= { c3gCdmaConnectionEntry 13 } c3gMobileIpErrorCode OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Mobile IP error code (please refer to RFC 2002)." ::= { c3gCdmaConnectionEntry 14 } c3gCdmaCurrentTransmitted OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Current number of bytes transmitted by modem for current connection." ::= { c3gCdmaConnectionEntry 15 } c3gCdmaCurrentReceived OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Current number of bytes received by modem for current connection." ::= { c3gCdmaConnectionEntry 16 } c3gCdmaCurrentCallStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), error(2), connecting(3), dormant(4), connected(5), disconnected(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current call status." ::= { c3gCdmaConnectionEntry 17 } c3gCdmaCurrentCallDuration OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Current call duration." DEFVAL { 0 } ::= { c3gCdmaConnectionEntry 18 } c3gCdmaCurrentCallType OBJECT-TYPE SYNTAX INTEGER { unknown(1), asyncData(2), voiceCall(3), packet1xRttCall(4), atAsyncDataCall(5), atVoiceCall(6), atPacketCall(7), faxCall(8), smsCall(9), otaCall(10), testCall(11), callWaiting(12), positionDetermination(13), dormant(14), e911Call(15) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current call type." ::= { c3gCdmaConnectionEntry 19 } c3gCdmaLastCallDisconnReason OBJECT-TYPE SYNTAX INTEGER { unknown(1), modemOffline(2), modemCdmaLocTilPowCyc(3), noService(4), abnormalCallEnd(5), baseStatIntercept(6), baseStatRelease(7), baseStatReleaseNoReas(8), baseStatReleaseSoRej(9), incomingCall(10), baseStatAlertStop(11), clientEndedCall(12), activationEndedOtasp(13), ndssFailure(14), maxAccesProbTransmit(15), persistTestFailure(16), ruimNotPresent(17), accessAttemptInProg(18), reasonUnspecified(19), recdRetryOrder(20), modemLocked(21), gpsCallEnded(22), smsCallEnded(23), noConcurrentService(24), noResponseFromBs(25), rejectedByBs(26), notCompatConcurServ(27), accessBlockedByBs(28), alreadyOnTraffChann(29), emergencyCall(30), dataCallEnded(31), busyHdr(32), billingOrAuthErrHdr(33), sysChangeDueToPrlHdr(34), hdrExitDueToPrl(35), noSessionHdr(36), callEndedHdr(37) } MAX-ACCESS read-only STATUS current DESCRIPTION "Last call disconnect reason: unknown(1) - Unknown modemOffline(2) - Modem offline modemCdmaLocTilPowCyc(3) - Modem CDMA locked till power cycle noService(4) - No service abnormalCallEnd(5) - Abnormal call end baseStatIntercept(6) - Base station intercept baseStatRelease(7) - Base station release baseStatReleaseNoReas(8) - Base station release (No reason) baseStatReleaseSoRej(9) - Base station release (SO reject) incomingCall(10) - Incoming call baseStatAlertStop(11) - Base station alert stop clientEndedCall(12) - Client ended call activationEndedOtasp(13) - Activation ended OTASP (Over- The-Air Service Provisioning) ndssFailure(14) - NDSS (Network and Distributed System Security) failure maxAccesProbTransmit(15) - Max access probes transmitted persistTestFailure(16) - Persistence test failure ruimNotPresent(17) - RUIM (Removable User Identity Module) not present accessAttemptInProg(18) - Access attempt in progress reasonUnspecified(19) - Reason unspecified recdRetryOrder(20) - Recd retry order modemLocked(21) - Modem Locked gpsCallEnded(22) - GPS call ended smsCallEnded(23) - SMS (Short Message Service) call ended noConcurrentService(24) - No concurrent service noResponseFromBs(25) - No response from BS (Base station) rejectedByBs(26) - Rejected by BS notCompatConcurServ(27) - Not compatible concurrent service accessBlockedByBs(28) - Access blocked by BS alreadyOnTraffChann(29) - Already on Traffic channel emergencyCall(30) - Emergency call dataCallEnded(31) - Data call ended busyHdr(32) - Busy (HDR) billingOrAuthErrHdr(33) - Billing or Auth error (HDR) sysChangeDueToPrlHdr(34) - System change due to PRL (HDR) hdrExitDueToPrl(35) - HDR exit due to PRL (HDR) noSessionHdr(36) - No Session (HDR) callEndedHdr(37) - Call ended (HDR)" ::= { c3gCdmaConnectionEntry 20 } c3gCdmaLastConnError OBJECT-TYPE SYNTAX INTEGER { none(1), invalidClientId(2), badCallType(3), badServiceType(4), expectingNumber(5), nullNumberBuffer(6), invalidDigits(7), outOfRangeNumber(8), nullAalphaBuffer(9), outOfRangeAlphaNumber(10), invalidOtaspActivatCode(11), modemOffline(12), modemLocked(13), unsupportedFlash(14), dialedNumberProhibited(15), onlyE911Calls(16), modemInUse(17), unsupportedServiceType(18), wrongCallType(19), invalidCommandCallState(20), invalidCommandModemState(21), noValidService(22), cannotAnswerIncomingCall(23), badPrivacySetting(24), noCommandBuffers(25), communicationProblem(26), unspecifiedError(27), invalidLastActiveNetwork(28), noCollocatedHdr(29), uimNotPresent(30) } MAX-ACCESS read-only STATUS current DESCRIPTION "Last connect error: none(1) - None invalidClientId(2) - Invalid client ID badCallType(3) - Bad call type badServiceType(4) - Bad service type expectingNumber(5) - Expecting number nullNumberBuffer(6) - Null number buffer invalidDigits(7) - Invalid digits outOfRangeNumber(8) - Out of range number nullAalphaBuffer(9) - Null alpha buffer outOfRangeAlphaNumber(10) - Out of range alpha number invalidOtaspActivatCode(11) - Invalid OTASP activation code modemOffline(12) - Modem offline modemLocked(13) - Modem locked unsupportedFlash(14) - Unsupported flash dialedNumberProhibited(15) - Dialed number prohibited onlyE911Calls(16) - Only E911 calls modemInUse(17) - Modem in use unsupportedServiceType(18) - Unsupported service type wrongCallType(19) - Wrong call type invalidCommandCallState(20) - Invalid command (call state) invalidCommandModemState(21) - Invalid command (modem state) noValidService(22) - No valid service cannotAnswerIncomingCall(23) - Cannot answer incoming call badPrivacySetting(24) - Bad privacy setting noCommandBuffers(25) - No command buffers communicationProblem(26) - Communication problem unspecifiedError(27) - Unspecified error invalidLastActiveNetwork(28) - Invalid last active network noCollocatedHdr(29) - No collocated HDR uimNotPresent(30) - UIM (User Identity Module) not present" ::= { c3gCdmaConnectionEntry 21 } c3gCdmaIdentityTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gCdmaIdentityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Cellular 3G CDMA identity table." ::= { c3gWanCdma 3 } c3gCdmaIdentityEntry OBJECT-TYPE SYNTAX C3gCdmaIdentityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the c3gCdmaIdentityTable." INDEX { entPhysicalIndex } ::= { c3gCdmaIdentityTable 1 } C3gCdmaIdentityEntry ::= SEQUENCE { c3gEsn DisplayString, c3gModemActivationStatus INTEGER, c3gAccountActivationDate DisplayString, c3gCdmaRoamingPreference INTEGER, c3gPrlVersion Unsigned32, c3gMdn DisplayString, c3gMsid DisplayString, c3gMsl DisplayString } c3gEsn OBJECT-TYPE SYNTAX DisplayString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates Electronic Serial Number (ESN)." ::= { c3gCdmaIdentityEntry 1 } c3gModemActivationStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), activated(2), notActivated(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Modem activation status." DEFVAL { unknown } ::= { c3gCdmaIdentityEntry 2 } c3gAccountActivationDate OBJECT-TYPE SYNTAX DisplayString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "Modem account activation date." ::= { c3gCdmaIdentityEntry 3 } c3gCdmaRoamingPreference OBJECT-TYPE SYNTAX INTEGER { unknown(1), home(2), affiliated(3), any(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the roaming preference: unknown(1) - preference unknown home(2) - home networks only affiliated(3) - roaming on affiliated networks any(4) - roaming on any network" DEFVAL { any } ::= { c3gCdmaIdentityEntry 4 } c3gPrlVersion OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Preferred Roaming List (PRL) version." DEFVAL { 0 } ::= { c3gCdmaIdentityEntry 5 } c3gMdn OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "Mobile Directory Number (MDN), a dialable number assigned to a wireless phone." ::= { c3gCdmaIdentityEntry 6 } c3gMsid OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "Mobile Station Identifier (MSID), MSID is utilized to distinguish the mobile station being programmed from other mobile stations during messaging and paging processes, including the downloading of programming information to the mobile station." ::= { c3gCdmaIdentityEntry 7 } c3gMsl OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "Mobile Subscriber Lock (MSL)." ::= { c3gCdmaIdentityEntry 8 } c3gCdmaNetworkTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gCdmaNetworkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Cellular 3G CDMA network table." ::= { c3gWanCdma 4 } c3gCdmaNetworkEntry OBJECT-TYPE SYNTAX C3gCdmaNetworkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the c3gCdmaNetworkTable." INDEX { entPhysicalIndex } ::= { c3gCdmaNetworkTable 1 } C3gCdmaNetworkEntry ::= SEQUENCE { c3gCdmaCurrentServiceStatus DisplayString, c3gCdmaHybridModePreference INTEGER, c3gCdmaCurrentRoamingStatus INTEGER, c3gCurrentIdleDigitalMode INTEGER, c3gCurrentSid Integer32, c3gCurrentNid Integer32, c3gCurrentCallSetupMode INTEGER, c3gSipUsername DisplayString, c3gSipPassword DisplayString, c3gServingBaseStationLongitude DisplayString, c3gServingBaseStationLatitude DisplayString } c3gCdmaCurrentServiceStatus OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Current service status." ::= { c3gCdmaNetworkEntry 1 } c3gCdmaHybridModePreference OBJECT-TYPE SYNTAX INTEGER { unknown(1), hybrid(2), evDoOnly(3), oneXRttOnly(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the hybrid mode preference: unknown(1) - preference unknown hybrid(2) - connect to EV-DO/1xRTT services evDoOnly(3) - connect to only EV-DO service oneXRttOnly(4) - connect to only 1xRTT service" DEFVAL { unknown } ::= { c3gCdmaNetworkEntry 2 } c3gCdmaCurrentRoamingStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), home(2), roamingWithSid(3), roamingWithoutSid(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current 1xRTT roaming status, roaming is a general term in wireless telecommunications that refers to the extending of connectivity service in a location that is different from the home location where the service was registered: unknown(1) - roaming status is unknown. home(2) - connectivity service in home location. roamingWithSid(3) - roaming with SID. roamingWithoutSid(4) - roaming without SID" DEFVAL { unknown } ::= { c3gCdmaNetworkEntry 3 } c3gCurrentIdleDigitalMode OBJECT-TYPE SYNTAX INTEGER { unknown(1), noService(2), amps(3), cdma(4), gsm(5), hdr(6), wcdma(7), gps(8), lte(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current idle digital mode: unknown(1) - service is unknown noService(2) - no service amps(3) - Advanced Mobile Phone Service (AMPS) cdma(4) - Code Division Multiple Access (CDMA) gsm(5) - Global System for Mobile communications (GSM) hdr(6) - High Data Rate (HDR) wcdma(7) - Wideband Code-Division Multiple-Access (WCDMA) gps(8) - Global Positioning System (GPS) lte(9) - Long Term Evolution (LTE)" DEFVAL { noService } ::= { c3gCdmaNetworkEntry 4 } c3gCurrentSid OBJECT-TYPE SYNTAX Integer32 (-1..32767) MAX-ACCESS read-write STATUS current DESCRIPTION "Current System Identifier (SID), SID is a 15-bit numeric identifiers used by cellular systems to identify the home system of a cellular telephone and by the cellular telephone to determine its roaming status. Value of '-1' indicates SID is 'Not Applicable'." ::= { c3gCdmaNetworkEntry 5 } c3gCurrentNid OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Current Network Identification (NID), NID is a 16-bit numeric identifiers used by cellular systems. Value of '-1' indicates NID is 'Not Applicable'." ::= { c3gCdmaNetworkEntry 6 } c3gCurrentCallSetupMode OBJECT-TYPE SYNTAX INTEGER { unknown(1), simpleIpOnly(2), mobileIpPreferWithSipFallback(3), mobileIpOnly(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Current call setup mode. The 1xEV-DO system supports packet data connections to a public or private data network using either mobile IP or simple IP protocol. For simple IP protocol, moving from the coverage area of one PDSN to another PDSN constitutes a change in packet data session. For mobile IP protocol, a packet data session can span several PDSNs as long as the user continuously maintains mobility bindings at the Home Agent (the IP address is persistent). The modes are: unknown(1) - mode is unknown simpleIpOnly(2) - simple IP only mobileIpPreferWithSipFallback(3) - prefer mobile IP with simple IP as fallback mode mobileIpOnly(4) - mobile IP only" DEFVAL { unknown } ::= { c3gCdmaNetworkEntry 7 } c3gSipUsername OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "Simple IP (SIP) user name." ::= { c3gCdmaNetworkEntry 8 } c3gSipPassword OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "Simple IP (SIP) password." ::= { c3gCdmaNetworkEntry 9 } c3gServingBaseStationLongitude OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Longitude of the serving base station." ::= { c3gCdmaNetworkEntry 10 } c3gServingBaseStationLatitude OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Latitude of the serving base station." ::= { c3gCdmaNetworkEntry 11 } c3gCdmaProfile OBJECT IDENTIFIER ::= { c3gWanCdma 5 } c3gCdmaProfileCommonTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gCdmaProfileCommonEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Cellular 3G CDMA profile common table." ::= { c3gCdmaProfile 1 } c3gCdmaProfileCommonEntry OBJECT-TYPE SYNTAX C3gCdmaProfileCommonEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the c3gCdmaProfileCommonTable." INDEX { entPhysicalIndex } ::= { c3gCdmaProfileCommonTable 1 } C3gCdmaProfileCommonEntry ::= SEQUENCE { c3gNumberOfDataProfileConfigurable Unsigned32, c3gCurrentActiveDataProfile Unsigned32 } c3gNumberOfDataProfileConfigurable OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "The number of data profiles configurable." DEFVAL { 0 } ::= { c3gCdmaProfileCommonEntry 1 } c3gCurrentActiveDataProfile OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "The current active data profile." ::= { c3gCdmaProfileCommonEntry 2 } c3gCdmaProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gCdmaProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Cellular 3G CDMA profile table." ::= { c3gCdmaProfile 2 } c3gCdmaProfileEntry OBJECT-TYPE SYNTAX C3gCdmaProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the c3gCdmaProfileTable." INDEX { entPhysicalIndex, c3gCdmaProfileIndex } ::= { c3gCdmaProfileTable 1 } C3gCdmaProfileEntry ::= SEQUENCE { c3gCdmaProfileIndex Integer32, c3gNai DisplayString, c3gAaaPassword DisplayString, c3gMnHaSs INTEGER, c3gMnHaSpi Unsigned32, c3gMnAaaSs INTEGER, c3gMnAaaSpi Unsigned32, c3gReverseTunnelPreference INTEGER, c3gHomeAddrType InetAddressType, c3gHomeAddr InetAddress, c3gPriHaAddrType InetAddressType, c3gPriHaAddr InetAddress, c3gSecHaAddrType InetAddressType, c3gSecHaAddr InetAddress } c3gCdmaProfileIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Profile index, combined with entPhysicalIndex to access the profile table c3gCdmaProfileTable." ::= { c3gCdmaProfileEntry 1 } c3gNai OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "Network Access Identifier (NAI). NAI is required to identify the mobile user and the network the mobile user intended to access. The NAI is provided by the mobile node to the dialed ISP during PPP authentication." ::= { c3gCdmaProfileEntry 2 } c3gAaaPassword OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the password for AAA." ::= { c3gCdmaProfileEntry 3 } c3gMnHaSs OBJECT-TYPE SYNTAX INTEGER { set(1), notSet(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Mobile Node (MN) Home Agent (HA) Shared Secret (SS) setting: set(1) - shared secret is set notSet(2) - shared secret is not set" DEFVAL { notSet } ::= { c3gCdmaProfileEntry 4 } c3gMnHaSpi OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Mobile Node (MN) Home Agent (HA) Security Parameter Index (SPI)." ::= { c3gCdmaProfileEntry 5 } c3gMnAaaSs OBJECT-TYPE SYNTAX INTEGER { set(1), notSet(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Mobile Node (MN) Authentication Authorization Accounting (AAA) Shared Secret (SS) setting: set(1) - shared secret is set notSet(2) - shared secret is not set" DEFVAL { notSet } ::= { c3gCdmaProfileEntry 6 } c3gMnAaaSpi OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Mobile Node (MN) Authentication Authorization Accounting (AAA) Security Parameter Index (SPI)." ::= { c3gCdmaProfileEntry 7 } c3gReverseTunnelPreference OBJECT-TYPE SYNTAX INTEGER { set(1), notSet(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Reverse tunnel preference." ::= { c3gCdmaProfileEntry 8 } c3gHomeAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "A value that represents the type of the IP Address stored in the object c3gHomeAddr." ::= { c3gCdmaProfileEntry 9 } c3gHomeAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "A unicast routable address assigned to a Mobile Node, used as the permanent address of the Mobile Node." ::= { c3gCdmaProfileEntry 10 } c3gPriHaAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "A value that represents the type of the IP Address stored in the object c3gPriHaAddr." ::= { c3gCdmaProfileEntry 11 } c3gPriHaAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The primary home agent address." ::= { c3gCdmaProfileEntry 12 } c3gSecHaAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "A value that represents the type of the IP Address stored in the object c3gSecHaAddr." ::= { c3gCdmaProfileEntry 13 } c3gSecHaAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The secondary home agent address." ::= { c3gCdmaProfileEntry 14 } c3gCdmaRadio OBJECT IDENTIFIER ::= { c3gWanCdma 6 } c3gCdma1xRttRadioTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gCdma1xRttRadioEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Cellular 3G CDMA 1xRTT radio table." ::= { c3gCdmaRadio 1 } c3gCdma1xRttRadioEntry OBJECT-TYPE SYNTAX C3gCdma1xRttRadioEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the c3gCdma1xRttRadioTable." INDEX { entPhysicalIndex } ::= { c3gCdma1xRttRadioTable 1 } C3gCdma1xRttRadioEntry ::= SEQUENCE { c3gCurrent1xRttRssi C3gRssi, c3gCurrent1xRttEcIo C3gEcIo, c3gCurrent1xRttChannelNumber Integer32, c3gCurrent1xRttChannelState INTEGER } c3gCurrent1xRttRssi OBJECT-TYPE SYNTAX C3gRssi MAX-ACCESS read-only STATUS current DESCRIPTION "Current 1xRTT RSSI value." ::= { c3gCdma1xRttRadioEntry 1 } c3gCurrent1xRttEcIo OBJECT-TYPE SYNTAX C3gEcIo MAX-ACCESS read-only STATUS current DESCRIPTION "Current 1xRTT Ec/Io value." ::= { c3gCdma1xRttRadioEntry 2 } c3gCurrent1xRttChannelNumber OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current 1xRTT channel number. Current channel number to which the modem is attached to the base station. Value of '-1' indicates 'No Service'." ::= { c3gCdma1xRttRadioEntry 3 } c3gCurrent1xRttChannelState OBJECT-TYPE SYNTAX INTEGER { unknown(1), notAcquired(2), acquired(3), scanning(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current 1xRTT channel state. Indicates whether the modem is scanning or has acquired the channel." DEFVAL { notAcquired } ::= { c3gCdma1xRttRadioEntry 4 } c3gCdma1xRttBandClassTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gCdma1xRttBandClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Cellular 3G CDMA 1xRTT band class table. This table contains band class information for each available band." ::= { c3gCdmaRadio 2 } c3gCdma1xRttBandClassEntry OBJECT-TYPE SYNTAX C3gCdma1xRttBandClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the c3gCdma1xRttBandClassTable." INDEX { entPhysicalIndex, c3gBandClassIndex } ::= { c3gCdma1xRttBandClassTable 1 } C3gCdma1xRttBandClassEntry ::= SEQUENCE { c3gBandClassIndex Integer32, c3g1xRttBandClass Unsigned32 } c3gBandClassIndex OBJECT-TYPE SYNTAX Integer32 (1..32) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Band class index, combined with entPhysicalIndex to access the band class table." ::= { c3gCdma1xRttBandClassEntry 1 } c3g1xRttBandClass OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains 1xRTT band class." ::= { c3gCdma1xRttBandClassEntry 2 } c3gCdmaEvDoRadioTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gCdmaEvDoRadioEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Cellular 3G CDMA EV-DO radio table." ::= { c3gCdmaRadio 3 } c3gCdmaEvDoRadioEntry OBJECT-TYPE SYNTAX C3gCdmaEvDoRadioEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the c3gCdmaEvDoRadioTable." INDEX { entPhysicalIndex } ::= { c3gCdmaEvDoRadioTable 1 } C3gCdmaEvDoRadioEntry ::= SEQUENCE { c3gCurrentEvDoRssi C3gRssi, c3gCurrentEvDoEcIo C3gEcIo, c3gCurrentEvDoChannelNumber Integer32, c3gSectorId DisplayString, c3gSubnetMask Unsigned32, c3gHdrColorCode Unsigned32, c3gPnOffset Unsigned32, c3gRxMainGainControl Integer32, c3gRxDiversityGainControl Integer32, c3gTxTotalPower Integer32, c3gTxGainAdjust Integer32, c3gCarrierToInterferenceRatio Unsigned32 } c3gCurrentEvDoRssi OBJECT-TYPE SYNTAX C3gRssi MAX-ACCESS read-only STATUS current DESCRIPTION "Current EV-DO RSSI value." ::= { c3gCdmaEvDoRadioEntry 1 } c3gCurrentEvDoEcIo OBJECT-TYPE SYNTAX C3gEcIo MAX-ACCESS read-only STATUS current DESCRIPTION "Current EV-DO Ec/Io value." ::= { c3gCdmaEvDoRadioEntry 2 } c3gCurrentEvDoChannelNumber OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current EV-DO channel number. Current channel number to which the modem is attached to the base station. Value of '-1' indicates 'No Service'." ::= { c3gCdmaEvDoRadioEntry 3 } c3gSectorId OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Sector ID of the base station to which the modem is attached." ::= { c3gCdmaEvDoRadioEntry 4 } c3gSubnetMask OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Subnet mask of the sector, not to be confused with the IP subnet mask." REFERENCE "3GPP2 C.S0024-B v1.0" ::= { c3gCdmaEvDoRadioEntry 5 } c3gHdrColorCode OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Color code of the sector." REFERENCE "3GPP2 C.S0024-B v1.0" ::= { c3gCdmaEvDoRadioEntry 6 } c3gPnOffset OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "PN offset. PN offset is a time offset from the beginning of the well-known pseudo-random noise sequence that is used to spread the signal from the base station." REFERENCE "3GPP2 C.S0024-B v1.0" ::= { c3gCdmaEvDoRadioEntry 7 } c3gRxMainGainControl OBJECT-TYPE SYNTAX Integer32 UNITS "dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Received main gain control for the modem. value of '-1' indicates the received main gain control is unavailable." ::= { c3gCdmaEvDoRadioEntry 8 } c3gRxDiversityGainControl OBJECT-TYPE SYNTAX Integer32 UNITS "dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Received diversity for the modem. value of '-1' indicates the received diversity is unavailable." ::= { c3gCdmaEvDoRadioEntry 9 } c3gTxTotalPower OBJECT-TYPE SYNTAX Integer32 UNITS "dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Transmit total power." ::= { c3gCdmaEvDoRadioEntry 10 } c3gTxGainAdjust OBJECT-TYPE SYNTAX Integer32 UNITS "dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Transmit gain adjust." ::= { c3gCdmaEvDoRadioEntry 11 } c3gCarrierToInterferenceRatio OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Carrier to interference ratio. Carrier-to-Interference ratio (C/I) is the ratio of power in an RF carrier to the interference power in the channel." ::= { c3gCdmaEvDoRadioEntry 12 } c3gCdmaEvDoBandClassTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gCdmaEvDoBandClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Cellular 3G CDMA EV-DO band class table. This table contains band class information for each available band." ::= { c3gCdmaRadio 4 } c3gCdmaEvDoBandClassEntry OBJECT-TYPE SYNTAX C3gCdmaEvDoBandClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the c3gCdmaEvDoBandClassTable." INDEX { entPhysicalIndex, c3gBandClassIndex } ::= { c3gCdmaEvDoBandClassTable 1 } C3gCdmaEvDoBandClassEntry ::= SEQUENCE { c3gEvDoBandClass Unsigned32 } c3gEvDoBandClass OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains EV-DO band class." ::= { c3gCdmaEvDoBandClassEntry 1 } c3gCdmaHistoryTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gCdmaHistoryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Cellular 3G CDMA history table. The history of RSSI are carried in an octet of string. Each octet in the octet string has a value from 0 to 150 and the 255 value is reserved to indicate an uninitialized (Invalid) value. The format of the octet string with n octets is as following: [ octet 0 is latest, octet 1 is latest-1, . . octet n-2 is oldest-1, octet n-1 is oldest ] To convert the provided value into dBm the following formula should be used: dBm = (-1)*value;" ::= { c3gCdmaRadio 5 } c3gCdmaHistoryEntry OBJECT-TYPE SYNTAX C3gCdmaHistoryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the c3gCdmaHistoryTable." INDEX { entPhysicalIndex } ::= { c3gCdmaHistoryTable 1 } C3gCdmaHistoryEntry ::= SEQUENCE { c3gCdmaHistory1xRttRssiPerSecond OCTET STRING, c3gCdmaHistory1xRttRssiPerMinute OCTET STRING, c3gCdmaHistory1xRttRssiPerHour OCTET STRING, c3gCdmaHistoryEvDoRssiPerSecond OCTET STRING, c3gCdmaHistoryEvDoRssiPerMinute OCTET STRING, c3gCdmaHistoryEvDoRssiPerHour OCTET STRING } c3gCdmaHistory1xRttRssiPerSecond OBJECT-TYPE SYNTAX OCTET STRING (SIZE (60)) UNITS "-dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Per-second 1xRTT RSSI history. This object contains a per-second history of 1xRTT RSSI values for the last 60 seconds." ::= { c3gCdmaHistoryEntry 1 } c3gCdmaHistory1xRttRssiPerMinute OBJECT-TYPE SYNTAX OCTET STRING (SIZE (60)) UNITS "-dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Per-minute 1xRTT weakest RSSI value history. This object contains a per-minute history of 1xRTT weakest RSSI values for the last 60 minutes. The octet in the string is the weakest RSSI value measured in a minute interval." ::= { c3gCdmaHistoryEntry 2 } c3gCdmaHistory1xRttRssiPerHour OBJECT-TYPE SYNTAX OCTET STRING (SIZE (72)) UNITS "-dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Per-hour 1xRTT weakest RSSI value history. This object contains a per-hour history of 1xRTT weakest RSSI values for the last 72 hours. The octet in the string is the weakest RSSI value measured in an hour interval." ::= { c3gCdmaHistoryEntry 3 } c3gCdmaHistoryEvDoRssiPerSecond OBJECT-TYPE SYNTAX OCTET STRING (SIZE (60)) UNITS "-dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Per-second EV-DO RSSI history. This object contains a per-second history of EV-DO RSSI values for the last 60 seconds." ::= { c3gCdmaHistoryEntry 4 } c3gCdmaHistoryEvDoRssiPerMinute OBJECT-TYPE SYNTAX OCTET STRING (SIZE (60)) UNITS "-dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Per-minute EV-DO weakest RSSI value history. This object contains a per-minute history of EV-DO weakest RSSI values for the last 60 minutes. The octet in the string is the weakest RSSI value measured in a minute interval." ::= { c3gCdmaHistoryEntry 5 } c3gCdmaHistoryEvDoRssiPerHour OBJECT-TYPE SYNTAX OCTET STRING (SIZE (72)) UNITS "-dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Per-hour EV-DO weakest RSSI value history. This object contains a per-hour history of EV-DO weakest RSSI values for the last 72 hours. The octet in the string is the weakest RSSI value measured in an hour interval." ::= { c3gCdmaHistoryEntry 6 } c3gCdmaSecurity OBJECT IDENTIFIER ::= { c3gWanCdma 7 } c3gCdmaSecurityTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gCdmaSecurityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Cellular 3G CDMA security table." ::= { c3gCdmaSecurity 1 } c3gCdmaSecurityEntry OBJECT-TYPE SYNTAX C3gCdmaSecurityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the c3gCdmaSecurityTable." INDEX { entPhysicalIndex } ::= { c3gCdmaSecurityTable 1 } C3gCdmaSecurityEntry ::= SEQUENCE { c3gCdmaPinSecurityStatus INTEGER, c3gCdmaPowerUpLockStatus INTEGER } c3gCdmaPinSecurityStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), locked(2), unlocked(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "CDMA Personal Identification Number (PIN) security: unknown(1) - PIN security unknown locked(2) - PIN security is locked unlocked(3) - PIN security is unlocked" DEFVAL { unlocked } ::= { c3gCdmaSecurityEntry 1 } c3gCdmaPowerUpLockStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), enabled(2), disabled(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "CDMA power up lock: unknown(1) - power up lock unknown enabled(2) - power up lock enabled disabled(3) - power up lock disabled" DEFVAL { disabled } ::= { c3gCdmaSecurityEntry 2 } c3gGsmIdentityTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gGsmIdentityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "." ::= { c3gWanGsm 1 } c3gGsmIdentityEntry OBJECT-TYPE SYNTAX C3gGsmIdentityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the c3gGsmIdentityTable." INDEX { entPhysicalIndex } ::= { c3gGsmIdentityTable 1 } C3gGsmIdentityEntry ::= SEQUENCE { c3gImsi DisplayString, c3gImei DisplayString, c3gIccId DisplayString, c3gMsisdn DisplayString, c3gFsn DisplayString, c3gModemStatus INTEGER, c3gGsmRoamingPreference INTEGER } c3gImsi OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "International Mobile Subscriber Identifier (IMSI), a unique 15-digit code used to identify an individual user on a GSM/LTE network." ::= { c3gGsmIdentityEntry 1 } c3gImei OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "International Mobile Equipment Identifier (IMEI), a unique 15 or 17 digit code used to identify an individual mobile station to a GSM, UMTS or LTE network." ::= { c3gGsmIdentityEntry 2 } c3gIccId OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the Integrated Circuit Card ID (ICCID). The ICCID is defined by the ITU-T recommendation E.118. ICCIDs are stored in the SIM cards and are also engraved or printed on the SIM card body during a process called personalization." ::= { c3gGsmIdentityEntry 3 } c3gMsisdn OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the Mobile Subscriber Integrated Services Digital Network Number (MSISDN). It is a number uniquely identifying a subscription in a GSM, UMTS or LTE mobile network. It represents the telephone number to the SIM card in a mobile/cellular phone." ::= { c3gGsmIdentityEntry 4 } c3gFsn OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Forward Sequence Number (FSN), a message acknowledgement method using sequence number in the forward direction." ::= { c3gGsmIdentityEntry 5 } c3gModemStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), offLine(2), onLine(3), lowPowerMode(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Modem status: unknown(1) - modem status is unknown offLine(2) - modem is off line onLine(3) - modem is on line lowPowerMode(4) - modem is in the low power mode" DEFVAL { unknown } ::= { c3gGsmIdentityEntry 6 } c3gGsmRoamingPreference OBJECT-TYPE SYNTAX INTEGER { unknown(1), home(2), roaming(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the roaming preference." ::= { c3gGsmIdentityEntry 7 } c3gGsmNetworkTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gGsmNetworkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Cellular GSM Network table. This table is applicable in both 3G and 4G-LTE technology mode" ::= { c3gWanGsm 2 } c3gGsmNetworkEntry OBJECT-TYPE SYNTAX C3gGsmNetworkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the c3gGsmNetworkTable." INDEX { entPhysicalIndex } ::= { c3gGsmNetworkTable 1 } C3gGsmNetworkEntry ::= SEQUENCE { c3gGsmLac Unsigned32, c3gGsmCurrentServiceStatus INTEGER, c3gGsmCurrentServiceError INTEGER, c3gGsmCurrentService INTEGER, c3gGsmPacketService INTEGER, c3gGsmCurrentRoamingStatus INTEGER, c3gGsmNetworkSelectionMode INTEGER, c3gGsmCountry DisplayString, c3gGsmNetwork DisplayString, c3gGsmMcc Integer32, c3gGsmMnc Integer32, c3gGsmRac Unsigned32, c3gGsmCurrentCellId Unsigned32, c3gGsmCurrentPrimaryScramblingCode Unsigned32, c3gGsmPlmnSelection INTEGER, c3gGsmRegPlmn DisplayString, c3gGsmPlmnAbbr DisplayString, c3gGsmServiceProvider DisplayString, c3gGsmTotalByteTransmitted Counter64, c3gGsmTotalByteReceived Counter64 } c3gGsmLac OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Location Area Code (LAC), also called as Tracking Area Code (TAC) in LTE standard. LAC/TAC is given by the base station." DEFVAL { 0 } ::= { c3gGsmNetworkEntry 1 } c3gGsmCurrentServiceStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), noService(2), normal(3), emergencyOnly(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current Service Status: unknown(1) - current service status is unknown noService(2) - no service normal(3) - service status is normal emergencyOnly(4) - emergency service only" DEFVAL { unknown } ::= { c3gGsmNetworkEntry 2 } c3gGsmCurrentServiceError OBJECT-TYPE SYNTAX INTEGER { unknown(1), none(2), imsiUnknownInHlr(3), illegalMs(4), imsiUnknownInVlr(5), imeiNotAccepted(6), illegalMe(7), gprsServNotAllowed(8), gprsNonGprsServNotAllow(9), msIdentUnknown(10), implicitlyDetached(11), plmnNotAllowed(12), lacNotAllowed(13), roamingNotAllowed(14), gprsServNotAllowInPlmn(15), noSuitableCellInLa(16), mscTempNotReachable(17), networkFailure(18), macFailure(19), synchFailure(20), congestion(21), gsmAuthenNotAccept(22), servOptionNotSupport(23), reqServOptionNotSub(24), servOptionOutOfOrder(25), callCannotIdentified(26), noPdpContextActivated(27), invalidMandatInfo(28), unpsecProtErr(29) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current service error: unknown(1) - Unknown none(2) - None imsiUnknownInHlr(3) - IMSI unknown in HLR (Home Location Register) illegalMs(4) - Illegal MS (Mobile Station) imsiUnknownInVlr(5) - IMSI unknown in VLR (Visitor Location Register) imeiNotAccepted(6) - IMEI not accepted illegalMe(7) - Illegal ME (Mobile Entity) gprsServNotAllowed(8) - GPRS services not allowed gprsNonGprsServNotAllow(9) - GPRS and non-GPRS services not allowed msIdentUnknown(10) - MS identity unknown implicitlyDetached(11) - Implicitly detached plmnNotAllowed(12) - PLMN not allowed lacNotAllowed(13) - LAC not allowed roamingNotAllowed(14) - Roaming not allowed gprsServNotAllowInPlmn(15) - GPRS services not allowed in this PLMN noSuitableCellInLa(16) - No suitable cells in LA (Location Area) mscTempNotReachable(17) - MSC (Mobile Switching Center) temporarily not reachable networkFailure(18) - Network failure macFailure(19) - MAC failure synchFailure(20) - Synch failure congestion(21) - Congestion gsmAuthenNotAccept(22) - GSM/LTE Authentication not accepted servOptionNotSupport(23) - Service option not supported reqServOptionNotSub(24) - Requested service option not subscribed servOptionOutOfOrder(25) - Service option out of order callCannotIdentified(26) - Call cannot be identified noPdpContextActivated(27) - No PDP context activated invalidMandatInfo(28) - Invalid mandatory info unpsecProtErr(29) - Unspecified protocol error" ::= { c3gGsmNetworkEntry 3 } c3gGsmCurrentService OBJECT-TYPE SYNTAX INTEGER { unknown(1), invalid(2), circuitSwitched(3), packetSwitched(4), combined(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current service type: unknown(1) - service type is unknown invalid(2) - no service circuitSwitched(3) - circuit switched service packetSwitched(4) - packet switched service combined(5) - combination of circuit and packet switched service" DEFVAL { unknown } ::= { c3gGsmNetworkEntry 4 } c3gGsmPacketService OBJECT-TYPE SYNTAX INTEGER { unknown(1), none(2), gprs(3), edge(4), umtsWcdma(5), hsdpa(6), hsupa(7), hspa(8), hspaPlus(9), lte(10) } MAX-ACCESS read-only STATUS current DESCRIPTION "Packet Service type: unknown(1) - service type is unknown. none(2) - no service. gprs(3) - General Packet Radio Service (GPRS). edge(4) - Enhanced Data rates for GSM Evolution (EDGE). umtsWcdma(5) - Universal Mobile Telecommunications System (UMTS) / Wideband Code-Division Multiple-Access (W-CDMA). hsdpa(6) - High-Speed Downlink Packet Access (HSDPA) hsdpa(7) - High-Speed Uplink Packet Access (HSUPA) hspa(8) - High-Speed Packet Access (HSPA) hspaPlus(9) - High-Speed Packet Access (HSPA) Plus lte(10) - Long Term Evolution" DEFVAL { unknown } ::= { c3gGsmNetworkEntry 5 } c3gGsmCurrentRoamingStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), roaming(2), home(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether the modem is in the home network or is roaming." DEFVAL { home } ::= { c3gGsmNetworkEntry 6 } c3gGsmNetworkSelectionMode OBJECT-TYPE SYNTAX INTEGER { unknown(1), automatic(2), manual(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Network selection mode. Can be manual selection mode or automatic selection mode. Set to automatic by default." DEFVAL { automatic } ::= { c3gGsmNetworkEntry 7 } c3gGsmCountry OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Country code. Country code string is given by the base station." ::= { c3gGsmNetworkEntry 8 } c3gGsmNetwork OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Network code. Network Code string is given by the base station." ::= { c3gGsmNetworkEntry 9 } c3gGsmMcc OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Mobile Country Code (MCC). Value of '-1' indicates MCC is 'Not Applicable'." DEFVAL { 0 } ::= { c3gGsmNetworkEntry 10 } c3gGsmMnc OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Mobile Network Code (MNC). Value of '-1' indicates MNC is 'Not Applicable'." DEFVAL { 0 } ::= { c3gGsmNetworkEntry 11 } c3gGsmRac OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Routing Area Code (RAC). RAC is given by the base station." DEFVAL { 0 } ::= { c3gGsmNetworkEntry 12 } c3gGsmCurrentCellId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Cell Identifier of current cell. Cell ID is given by the base station." DEFVAL { 0 } ::= { c3gGsmNetworkEntry 13 } c3gGsmCurrentPrimaryScramblingCode OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Primary scrambling code of current cell. The primary scrambling code is typically identified through symbol-by-symbol correlation over the CPICH (Common Pilot Channel) with all codes within the code group, after the primary scrambling code has been identified, the Primary CCPCH can be detected and the system and cell specific BCH information can be read." DEFVAL { 0 } ::= { c3gGsmNetworkEntry 14 } c3gGsmPlmnSelection OBJECT-TYPE SYNTAX INTEGER { unknown(1), manual(2), automatic(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Public Land Mobile Network (PLMN) selection. Can be manual selection mode or automatic selection mode. Set to automatic by default." DEFVAL { automatic } ::= { c3gGsmNetworkEntry 15 } c3gGsmRegPlmn OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Registered PLMN." ::= { c3gGsmNetworkEntry 16 } c3gGsmPlmnAbbr OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "PLMN abbreviated number." ::= { c3gGsmNetworkEntry 17 } c3gGsmServiceProvider OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Service provider." ::= { c3gGsmNetworkEntry 18 } c3gGsmTotalByteTransmitted OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of bytes transmitted for all calls. It is the total number of bytes transmitted by modem, not to be confused with the number of bytes transmitted through the interface." ::= { c3gGsmNetworkEntry 19 } c3gGsmTotalByteReceived OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of bytes received for all calls. It is the total number of bytes received by modem, not to be confused with the number of bytes received from the interface." ::= { c3gGsmNetworkEntry 20 } c3gGsmPdpProfile OBJECT IDENTIFIER ::= { c3gWanGsm 3 } c3gGsmPdpProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gGsmPdpProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Cellular GSM PDP profiles table. Cellular device contains multiple profile entries which can be used to establish cellular data connections (PDP contexts). Users can choose any of available PDP profiles to establish data connections. Data connections are described in c3gGsmPacketSessionTable. This table is applicable in only 3G technology mode. Refer CISCO-WAN-CELL-EXT-MIB when in 4G-LTE mode." ::= { c3gGsmPdpProfile 1 } c3gGsmPdpProfileEntry OBJECT-TYPE SYNTAX C3gGsmPdpProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the c3gGsmPdpProfileTable." INDEX { entPhysicalIndex, c3gGsmPdpProfileIndex } ::= { c3gGsmPdpProfileTable 1 } C3gGsmPdpProfileEntry ::= SEQUENCE { c3gGsmPdpProfileIndex Integer32, c3gGsmPdpProfileType C3gPdpType, c3gGsmPdpProfileAddr DisplayString, c3gGsmPdpProfileApn DisplayString, c3gGsmPdpProfileAuthenType INTEGER, c3gGsmPdpProfileUsername DisplayString, c3gGsmPdpProfilePassword DisplayString, c3gGsmPdpProfileRowStatus RowStatus } c3gGsmPdpProfileIndex OBJECT-TYPE SYNTAX Integer32 (1..1000) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Profile index, combined with entPhysicalIndex to access profile table." ::= { c3gGsmPdpProfileEntry 1 } c3gGsmPdpProfileType OBJECT-TYPE SYNTAX C3gPdpType MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates configured Packet Data Protocol (PDP) type." DEFVAL { unknown } ::= { c3gGsmPdpProfileEntry 2 } c3gGsmPdpProfileAddr OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-create STATUS current DESCRIPTION "Configured PDP/EPS Bearer address. PDP type is defined in c3gGsmPdpProfileType." ::= { c3gGsmPdpProfileEntry 3 } c3gGsmPdpProfileApn OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates profile Access Point Name (APN). This information is provided by the service provider." ::= { c3gGsmPdpProfileEntry 4 } c3gGsmPdpProfileAuthenType OBJECT-TYPE SYNTAX INTEGER { unknown(1), none(2), chap(3), pap(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates PDP authentication type supported. CHAP and PAP are supported in GSM. The type of authentication to be used is provided by the service provider." DEFVAL { unknown } ::= { c3gGsmPdpProfileEntry 5 } c3gGsmPdpProfileUsername OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the username to be used for PDP authentication. This information is provided by the service provider." ::= { c3gGsmPdpProfileEntry 6 } c3gGsmPdpProfilePassword OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the password to be used for PDP authentication. This information is provided by the service provider." ::= { c3gGsmPdpProfileEntry 7 } c3gGsmPdpProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. This object is used to manage creation, modification and deletion of rows in this table." ::= { c3gGsmPdpProfileEntry 8 } c3gGsmPacketSessionTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gGsmPacketSessionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Cellular 3G GSM packet session table. This table is applicable in only 3G technology mode. Refer CISCO-WAN-CELL-EXT-MIB when in 4G-LTE mode." ::= { c3gGsmPdpProfile 2 } c3gGsmPacketSessionEntry OBJECT-TYPE SYNTAX C3gGsmPacketSessionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the c3gGsmPacketSessionTable." INDEX { entPhysicalIndex, c3gGsmPdpProfileIndex } ::= { c3gGsmPacketSessionTable 1 } C3gGsmPacketSessionEntry ::= SEQUENCE { c3gGsmPacketSessionStatus INTEGER, c3gGsmPdpType C3gPdpType, c3gGsmPdpAddress DisplayString } c3gGsmPacketSessionStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), active(2), inactive(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates PDP session status of the profile. This is active when the call is established and PDP contextr has become active." DEFVAL { inactive } ::= { c3gGsmPacketSessionEntry 1 } c3gGsmPdpType OBJECT-TYPE SYNTAX C3gPdpType MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates current session PDP type." ::= { c3gGsmPacketSessionEntry 2 } c3gGsmPdpAddress OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Current session PDP context/EPS Bearer address. PDP type is obtained from c3gGsmPdpType." ::= { c3gGsmPacketSessionEntry 3 } c3gGsmReqUmtsQosTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gGsmReqUmtsQosEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Requested UMTS QoS parameters table. This table contains UMTS QoS parameters requested by modem to the cellular network via PDP Context Activation Request message. The requested UMTS QoS profile is optional. This table is applicable only in 3G technology mode." ::= { c3gGsmPdpProfile 3 } c3gGsmReqUmtsQosEntry OBJECT-TYPE SYNTAX C3gGsmReqUmtsQosEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the c3gGsmReqUmtsQosTable." INDEX { entPhysicalIndex, c3gGsmPdpProfileIndex } ::= { c3gGsmReqUmtsQosTable 1 } C3gGsmReqUmtsQosEntry ::= SEQUENCE { c3gGsmReqUmtsQosTrafficClass C3gUmtsQosTrafficClass, c3gGsmReqUmtsQosMaxUpLinkBitRate C3gUmtsQosLinkBitRate, c3gGsmReqUmtsQosMaxDownLinkBitRate C3gUmtsQosLinkBitRate, c3gGsmReqUmtsQosGuaUpLinkBitRate C3gUmtsQosLinkBitRate, c3gGsmReqUmtsQosGuaDownLinkBitRate C3gUmtsQosLinkBitRate, c3gGsmReqUmtsQosOrder C3gUmtsQosOrder, c3gGsmReqUmtsQosErroneousSdu C3gUmtsQosErroneousSdu, c3gGsmReqUmtsQosMaxSduSize Unsigned32, c3gGsmReqUmtsQosSer C3gUmtsQosSer, c3gGsmReqUmtsQosBer C3gUmtsQosBer, c3gGsmReqUmtsQosDelay Unsigned32, c3gGsmReqUmtsQosPriority C3gUmtsQosPriority, c3gGsmReqUmtsQosSrcStatDescriptor C3gUmtsQosSrcStatDescriptor, c3gGsmReqUmtsQosSignalIndication C3gUmtsQosSignalIndication, c3gGsmReqUmtsQosRowStatus RowStatus } c3gGsmReqUmtsQosTrafficClass OBJECT-TYPE SYNTAX C3gUmtsQosTrafficClass MAX-ACCESS read-create STATUS current DESCRIPTION "Request UMTS QoS traffic classes." ::= { c3gGsmReqUmtsQosEntry 2 } c3gGsmReqUmtsQosMaxUpLinkBitRate OBJECT-TYPE SYNTAX C3gUmtsQosLinkBitRate MAX-ACCESS read-create STATUS current DESCRIPTION "Request UMTS QoS maximum uplink bit rate." ::= { c3gGsmReqUmtsQosEntry 3 } c3gGsmReqUmtsQosMaxDownLinkBitRate OBJECT-TYPE SYNTAX C3gUmtsQosLinkBitRate MAX-ACCESS read-create STATUS current DESCRIPTION "Request UMTS QoS maximum downlink bit rate." ::= { c3gGsmReqUmtsQosEntry 4 } c3gGsmReqUmtsQosGuaUpLinkBitRate OBJECT-TYPE SYNTAX C3gUmtsQosLinkBitRate MAX-ACCESS read-create STATUS current DESCRIPTION "Request UMTS QoS guaranteed uplink bit rate." ::= { c3gGsmReqUmtsQosEntry 5 } c3gGsmReqUmtsQosGuaDownLinkBitRate OBJECT-TYPE SYNTAX C3gUmtsQosLinkBitRate MAX-ACCESS read-create STATUS current DESCRIPTION "Request UMTS QoS guaranteed downlink bit rate." ::= { c3gGsmReqUmtsQosEntry 6 } c3gGsmReqUmtsQosOrder OBJECT-TYPE SYNTAX C3gUmtsQosOrder MAX-ACCESS read-create STATUS current DESCRIPTION "Request UMTS QoS deliver order." ::= { c3gGsmReqUmtsQosEntry 7 } c3gGsmReqUmtsQosErroneousSdu OBJECT-TYPE SYNTAX C3gUmtsQosErroneousSdu MAX-ACCESS read-create STATUS current DESCRIPTION "Request UMTS QoS Delivery of Erroneous SDU." ::= { c3gGsmReqUmtsQosEntry 8 } c3gGsmReqUmtsQosMaxSduSize OBJECT-TYPE SYNTAX Unsigned32 (0..1520) UNITS "bytes" MAX-ACCESS read-create STATUS current DESCRIPTION "Request UMTS QoS maximum SDU size, the valid range is between 1 and 1520 bytes. Value of '0' indicates the maximum SDU size is unspecified." ::= { c3gGsmReqUmtsQosEntry 9 } c3gGsmReqUmtsQosSer OBJECT-TYPE SYNTAX C3gUmtsQosSer MAX-ACCESS read-create STATUS current DESCRIPTION "Request UMTS QoS SDU error ratio." ::= { c3gGsmReqUmtsQosEntry 10 } c3gGsmReqUmtsQosBer OBJECT-TYPE SYNTAX C3gUmtsQosBer MAX-ACCESS read-create STATUS current DESCRIPTION "Request UMTS QoS residual bit error ratio." ::= { c3gGsmReqUmtsQosEntry 11 } c3gGsmReqUmtsQosDelay OBJECT-TYPE SYNTAX Unsigned32 (0..4000) UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Request UMTS QoS transfer delay in ms, the valid range is between 1 and 4000 ms. Value of '0' indicates the QoS delay is unspecified." ::= { c3gGsmReqUmtsQosEntry 12 } c3gGsmReqUmtsQosPriority OBJECT-TYPE SYNTAX C3gUmtsQosPriority MAX-ACCESS read-create STATUS current DESCRIPTION "Request UMTS QoS traffic handling priority." ::= { c3gGsmReqUmtsQosEntry 13 } c3gGsmReqUmtsQosSrcStatDescriptor OBJECT-TYPE SYNTAX C3gUmtsQosSrcStatDescriptor MAX-ACCESS read-create STATUS current DESCRIPTION "Request UMTS QoS source statistics descriptor." ::= { c3gGsmReqUmtsQosEntry 14 } c3gGsmReqUmtsQosSignalIndication OBJECT-TYPE SYNTAX C3gUmtsQosSignalIndication MAX-ACCESS read-create STATUS current DESCRIPTION "Request UMTS QoS signalling indication." ::= { c3gGsmReqUmtsQosEntry 15 } c3gGsmReqUmtsQosRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. This object is used to manage creation, modification and deletion of rows in this table." ::= { c3gGsmReqUmtsQosEntry 16 } c3gGsmMinUmtsQosTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gGsmMinUmtsQosEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Minimum acceptable UMTS QoS table. This table contains minimum acceptable UMTS QoS parameters which is checked by the MT (Mobile Termination) against the negotiated profile returned in the Activate PDP Context Accept message. The minimum acceptable UMTS QoS profile is optional. This table is applicable only in 3G technology mode." ::= { c3gGsmPdpProfile 4 } c3gGsmMinUmtsQosEntry OBJECT-TYPE SYNTAX C3gGsmMinUmtsQosEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the c3gGsmMinUmtsQosTable." INDEX { entPhysicalIndex, c3gGsmPdpProfileIndex } ::= { c3gGsmMinUmtsQosTable 1 } C3gGsmMinUmtsQosEntry ::= SEQUENCE { c3gGsmMinUmtsQosTrafficClass C3gUmtsQosTrafficClass, c3gGsmMinUmtsQosMaxUpLinkBitRate C3gUmtsQosLinkBitRate, c3gGsmMinUmtsQosMaxDownLinkBitRate C3gUmtsQosLinkBitRate, c3gGsmMinUmtsQosGuaUpLinkBitRate C3gUmtsQosLinkBitRate, c3gGsmMinUmtsQosGuaDownLinkBitRate C3gUmtsQosLinkBitRate, c3gGsmMinUmtsQosOrder C3gUmtsQosOrder, c3gGsmMinUmtsQosErroneousSdu C3gUmtsQosErroneousSdu, c3gGsmMinUmtsQosMaxSduSize Unsigned32, c3gGsmMinUmtsQosSer C3gUmtsQosSer, c3gGsmMinUmtsQosBer C3gUmtsQosBer, c3gGsmMinUmtsQosDelay Unsigned32, c3gGsmMinUmtsQosPriority C3gUmtsQosPriority, c3gGsmMinUmtsQosSrcStatDescriptor C3gUmtsQosSrcStatDescriptor, c3gGsmMinUmtsQosSignalIndication C3gUmtsQosSignalIndication, c3gGsmMinUmtsQosRowStatus RowStatus } c3gGsmMinUmtsQosTrafficClass OBJECT-TYPE SYNTAX C3gUmtsQosTrafficClass MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum UMTS QoS traffic classes." ::= { c3gGsmMinUmtsQosEntry 1 } c3gGsmMinUmtsQosMaxUpLinkBitRate OBJECT-TYPE SYNTAX C3gUmtsQosLinkBitRate MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum UMTS QoS maximum uplink bit rate." ::= { c3gGsmMinUmtsQosEntry 2 } c3gGsmMinUmtsQosMaxDownLinkBitRate OBJECT-TYPE SYNTAX C3gUmtsQosLinkBitRate MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum UMTS QoS maximum downlink bit rate." ::= { c3gGsmMinUmtsQosEntry 3 } c3gGsmMinUmtsQosGuaUpLinkBitRate OBJECT-TYPE SYNTAX C3gUmtsQosLinkBitRate MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum UMTS QoS guaranteed uplink bit rate." ::= { c3gGsmMinUmtsQosEntry 4 } c3gGsmMinUmtsQosGuaDownLinkBitRate OBJECT-TYPE SYNTAX C3gUmtsQosLinkBitRate MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum UMTS QoS guaranteed downlink bit rate." ::= { c3gGsmMinUmtsQosEntry 5 } c3gGsmMinUmtsQosOrder OBJECT-TYPE SYNTAX C3gUmtsQosOrder MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum UMTS QoS deliver order." ::= { c3gGsmMinUmtsQosEntry 6 } c3gGsmMinUmtsQosErroneousSdu OBJECT-TYPE SYNTAX C3gUmtsQosErroneousSdu MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum UMTS QoS Delivery of Erroneous SDU." ::= { c3gGsmMinUmtsQosEntry 7 } c3gGsmMinUmtsQosMaxSduSize OBJECT-TYPE SYNTAX Unsigned32 (0..1520) UNITS "bytes" MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum UMTS maximum SDU size, the valid range is between 1 and 1520 bytes. Value of '0' indicates the maximum SDU size is unspecified." ::= { c3gGsmMinUmtsQosEntry 8 } c3gGsmMinUmtsQosSer OBJECT-TYPE SYNTAX C3gUmtsQosSer MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum UMTS QoS SDU error ratio." ::= { c3gGsmMinUmtsQosEntry 9 } c3gGsmMinUmtsQosBer OBJECT-TYPE SYNTAX C3gUmtsQosBer MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum UMTS residual bit error ratio." ::= { c3gGsmMinUmtsQosEntry 10 } c3gGsmMinUmtsQosDelay OBJECT-TYPE SYNTAX Unsigned32 (0..4000) UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum UMTS transfer delay in ms, the valid range is between 1 and 4000 ms. Value of '0' indicates the QoS delay is unspecified." ::= { c3gGsmMinUmtsQosEntry 11 } c3gGsmMinUmtsQosPriority OBJECT-TYPE SYNTAX C3gUmtsQosPriority MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum UMTS QoS traffic handling priority." ::= { c3gGsmMinUmtsQosEntry 12 } c3gGsmMinUmtsQosSrcStatDescriptor OBJECT-TYPE SYNTAX C3gUmtsQosSrcStatDescriptor MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum UMTS QoS source statistics descriptor." ::= { c3gGsmMinUmtsQosEntry 13 } c3gGsmMinUmtsQosSignalIndication OBJECT-TYPE SYNTAX C3gUmtsQosSignalIndication MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum UMTS QoS signalling indication." ::= { c3gGsmMinUmtsQosEntry 14 } c3gGsmMinUmtsQosRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. This object is used to manage creation, modification and deletion of rows in this table." ::= { c3gGsmMinUmtsQosEntry 15 } c3gGsmNegoUmtsQosTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gGsmNegoUmtsQosEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Negotiated UMTS QoS table. This table contains negotiated UMTS QoS parameters returned in the Activate PDP Context Accept message. The objects in this table are valid only if the value of object c3gGsmPacketSessionStatus defined in c3gGsmPacketSessionTable is 'active'. This table is applicable only in 3G technology mode." ::= { c3gGsmPdpProfile 5 } c3gGsmNegoUmtsQosEntry OBJECT-TYPE SYNTAX C3gGsmNegoUmtsQosEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the c3gGsmNegoUmtsQosTable." INDEX { entPhysicalIndex, c3gGsmPdpProfileIndex } ::= { c3gGsmNegoUmtsQosTable 1 } C3gGsmNegoUmtsQosEntry ::= SEQUENCE { c3gGsmNegoUmtsQosTrafficClass C3gUmtsQosTrafficClass, c3gGsmNegoUmtsQosMaxUpLinkBitRate C3gUmtsQosLinkBitRate, c3gGsmNegoUmtsQosMaxDownLinkBitRate C3gUmtsQosLinkBitRate, c3gGsmNegoUmtsQosGuaUpLinkBitRate C3gUmtsQosLinkBitRate, c3gGsmNegoUmtsQosGuaDownLinkBitRate C3gUmtsQosLinkBitRate, c3gGsmNegoUmtsQosOrder C3gUmtsQosOrder, c3gGsmNegoUmtsQosErroneousSdu C3gUmtsQosErroneousSdu, c3gGsmNegoUmtsQosMaxSduSize Unsigned32, c3gGsmNegoUmtsQosSer C3gUmtsQosSer, c3gGsmNegoUmtsQosBer C3gUmtsQosBer, c3gGsmNegoUmtsQosDelay Unsigned32, c3gGsmNegoUmtsQosPriority C3gUmtsQosPriority, c3gGsmNegoUmtsQosSrcStatDescriptor C3gUmtsQosSrcStatDescriptor, c3gGsmNegoUmtsQosSignalIndication C3gUmtsQosSignalIndication } c3gGsmNegoUmtsQosTrafficClass OBJECT-TYPE SYNTAX C3gUmtsQosTrafficClass MAX-ACCESS read-only STATUS current DESCRIPTION "Negotiated UMTS QoS traffic classes." ::= { c3gGsmNegoUmtsQosEntry 1 } c3gGsmNegoUmtsQosMaxUpLinkBitRate OBJECT-TYPE SYNTAX C3gUmtsQosLinkBitRate MAX-ACCESS read-only STATUS current DESCRIPTION "Negotiated UMTS QoS maximum uplink bit rate." ::= { c3gGsmNegoUmtsQosEntry 2 } c3gGsmNegoUmtsQosMaxDownLinkBitRate OBJECT-TYPE SYNTAX C3gUmtsQosLinkBitRate MAX-ACCESS read-only STATUS current DESCRIPTION "Negotiated UMTS QoS maximum downlink bit rate." ::= { c3gGsmNegoUmtsQosEntry 3 } c3gGsmNegoUmtsQosGuaUpLinkBitRate OBJECT-TYPE SYNTAX C3gUmtsQosLinkBitRate MAX-ACCESS read-only STATUS current DESCRIPTION "Negotiated UMTS QoS guaranteed uplink bit rate." ::= { c3gGsmNegoUmtsQosEntry 4 } c3gGsmNegoUmtsQosGuaDownLinkBitRate OBJECT-TYPE SYNTAX C3gUmtsQosLinkBitRate MAX-ACCESS read-only STATUS current DESCRIPTION "Negotiated UMTS QoS guaranteed downlink bit rate." ::= { c3gGsmNegoUmtsQosEntry 5 } c3gGsmNegoUmtsQosOrder OBJECT-TYPE SYNTAX C3gUmtsQosOrder MAX-ACCESS read-only STATUS current DESCRIPTION "Negotiated UMTS QoS deliver order." ::= { c3gGsmNegoUmtsQosEntry 6 } c3gGsmNegoUmtsQosErroneousSdu OBJECT-TYPE SYNTAX C3gUmtsQosErroneousSdu MAX-ACCESS read-only STATUS current DESCRIPTION "Negotiated UMTS QoS Delivery of Erroneous SDU." ::= { c3gGsmNegoUmtsQosEntry 7 } c3gGsmNegoUmtsQosMaxSduSize OBJECT-TYPE SYNTAX Unsigned32 (0..1520) UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Negotiated UMTS QoS maximum SDU size, the valid range is between 1 and 1520 bytes. Value of '0' indicates the maximum SDU size is subscribed." ::= { c3gGsmNegoUmtsQosEntry 8 } c3gGsmNegoUmtsQosSer OBJECT-TYPE SYNTAX C3gUmtsQosSer MAX-ACCESS read-only STATUS current DESCRIPTION "Negotiated UMTS QoS SDU error ratio." ::= { c3gGsmNegoUmtsQosEntry 9 } c3gGsmNegoUmtsQosBer OBJECT-TYPE SYNTAX C3gUmtsQosBer MAX-ACCESS read-only STATUS current DESCRIPTION "Negotiated UMTS QoS residual bit error ratio." ::= { c3gGsmNegoUmtsQosEntry 10 } c3gGsmNegoUmtsQosDelay OBJECT-TYPE SYNTAX Unsigned32 (0..4000) UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Negotiated UMTS QoS transfer delay in ms, the valid range is between 1 and 4000 ms. Value of '0' indicates the QoS delay is subscribed." ::= { c3gGsmNegoUmtsQosEntry 11 } c3gGsmNegoUmtsQosPriority OBJECT-TYPE SYNTAX C3gUmtsQosPriority MAX-ACCESS read-only STATUS current DESCRIPTION "Negotiated UMTS QoS traffic handling priority." ::= { c3gGsmNegoUmtsQosEntry 12 } c3gGsmNegoUmtsQosSrcStatDescriptor OBJECT-TYPE SYNTAX C3gUmtsQosSrcStatDescriptor MAX-ACCESS read-only STATUS current DESCRIPTION "Negotiated UMTS QoS source statistics descriptor." ::= { c3gGsmNegoUmtsQosEntry 13 } c3gGsmNegoUmtsQosSignalIndication OBJECT-TYPE SYNTAX C3gUmtsQosSignalIndication MAX-ACCESS read-only STATUS current DESCRIPTION "Negotiated UMTS QoS signalling indication." ::= { c3gGsmNegoUmtsQosEntry 14 } c3gGsmReqGprsQosTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gGsmReqGprsQosEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Requested GPRS QoS parameters table. This table contains GPRS QoS parameters requested by modem to the cellular network via PDP Context Request message. The requested GPRS QoS profile is optional. This table is applicable only in 3G technology mode." ::= { c3gGsmPdpProfile 6 } c3gGsmReqGprsQosEntry OBJECT-TYPE SYNTAX C3gGsmReqGprsQosEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the c3gGsmReqGprsQosTable." INDEX { entPhysicalIndex, c3gGsmPdpProfileIndex } ::= { c3gGsmReqGprsQosTable 1 } C3gGsmReqGprsQosEntry ::= SEQUENCE { c3gGsmReqGprsQosPrecedence C3gGprsQosPrecedence, c3gGsmReqGprsQosDelay C3gGprsQosDelay, c3gGsmReqGprsQosReliability C3gGprsQosReliability, c3gGsmReqGprsQosPeakRate C3gGprsQosPeakRate, c3gGsmReqGprsQosMeanRate C3gGprsQosMeanRate, c3gGsmReqGprsQosRowStatus RowStatus } c3gGsmReqGprsQosPrecedence OBJECT-TYPE SYNTAX C3gGprsQosPrecedence MAX-ACCESS read-create STATUS current DESCRIPTION "Request GPRS QoS precedence." ::= { c3gGsmReqGprsQosEntry 1 } c3gGsmReqGprsQosDelay OBJECT-TYPE SYNTAX C3gGprsQosDelay MAX-ACCESS read-create STATUS current DESCRIPTION "Request GPRS QoS delay classes." ::= { c3gGsmReqGprsQosEntry 2 } c3gGsmReqGprsQosReliability OBJECT-TYPE SYNTAX C3gGprsQosReliability MAX-ACCESS read-create STATUS current DESCRIPTION "Request GPRS QoS reliability." ::= { c3gGsmReqGprsQosEntry 3 } c3gGsmReqGprsQosPeakRate OBJECT-TYPE SYNTAX C3gGprsQosPeakRate MAX-ACCESS read-create STATUS current DESCRIPTION "Request GPRS QoS peak rate." ::= { c3gGsmReqGprsQosEntry 4 } c3gGsmReqGprsQosMeanRate OBJECT-TYPE SYNTAX C3gGprsQosMeanRate UNITS "octet-per-hour" MAX-ACCESS read-create STATUS current DESCRIPTION "Request GPRS QoS mean rate." ::= { c3gGsmReqGprsQosEntry 5 } c3gGsmReqGprsQosRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. This object is used to manage creation, modification and deletion of rows in this table." ::= { c3gGsmReqGprsQosEntry 6 } c3gGsmMinGprsQosTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gGsmMinGprsQosEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Minimum acceptable GPRS QoS table. This table contains minimum acceptable GPRS QoS parameters which is checked by the MT (Mobile Termination) against the negotiated profile returned in the Activate PDP Context Accept message. The minimum acceptable GPRS QoS profile is optional. This table is applicable only in 3G technology mode." ::= { c3gGsmPdpProfile 7 } c3gGsmMinGprsQosEntry OBJECT-TYPE SYNTAX C3gGsmMinGprsQosEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the c3gGsmMinGprsQosTable." INDEX { entPhysicalIndex, c3gGsmPdpProfileIndex } ::= { c3gGsmMinGprsQosTable 1 } C3gGsmMinGprsQosEntry ::= SEQUENCE { c3gGsmMinGprsQosPrecedence C3gGprsQosPrecedence, c3gGsmMinGprsQosDelay C3gGprsQosDelay, c3gGsmMinGprsQosReliability C3gGprsQosReliability, c3gGsmMinGprsQosPeakRate C3gGprsQosPeakRate, c3gGsmMinGprsQosMeanRate C3gGprsQosMeanRate, c3gGsmMinGprsQosRowStatus RowStatus } c3gGsmMinGprsQosPrecedence OBJECT-TYPE SYNTAX C3gGprsQosPrecedence MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum GPRS QoS precedence." ::= { c3gGsmMinGprsQosEntry 1 } c3gGsmMinGprsQosDelay OBJECT-TYPE SYNTAX C3gGprsQosDelay MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum GPRS QoS delay classes." ::= { c3gGsmMinGprsQosEntry 2 } c3gGsmMinGprsQosReliability OBJECT-TYPE SYNTAX C3gGprsQosReliability MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum GPRS QoS reliability." ::= { c3gGsmMinGprsQosEntry 3 } c3gGsmMinGprsQosPeakRate OBJECT-TYPE SYNTAX C3gGprsQosPeakRate MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum GPRS QoS peak rate." ::= { c3gGsmMinGprsQosEntry 4 } c3gGsmMinGprsQosMeanRate OBJECT-TYPE SYNTAX C3gGprsQosMeanRate UNITS "octet-per-hour" MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum GPRS QoS mean rate." ::= { c3gGsmMinGprsQosEntry 5 } c3gGsmMinGprsQosRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. This object is used to manage creation, modification and deletion of rows in this table." ::= { c3gGsmMinGprsQosEntry 6 } c3gGsmNegoGprsQosTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gGsmNegoGprsQosEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Negotiated GPRS QoS table. This table contains negotiated GPRS QoS parameters returned in the Activate PDP Context Accept message. The objects in this table are valid only if the value of object c3gGsmPacketSessionStatus defined in c3gGsmPacketSessionTable is 'active'. This table is applicable only in 3G technology mode." ::= { c3gGsmPdpProfile 8 } c3gGsmNegoGprsQosEntry OBJECT-TYPE SYNTAX C3gGsmNegoGprsQosEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the c3gGsmNegoGprsQosTable." INDEX { entPhysicalIndex, c3gGsmPdpProfileIndex } ::= { c3gGsmNegoGprsQosTable 1 } C3gGsmNegoGprsQosEntry ::= SEQUENCE { c3gGsmNegoGprsQosPrecedence C3gGprsQosPrecedence, c3gGsmNegoGprsQosDelay C3gGprsQosDelay, c3gGsmNegoGprsQosReliability C3gGprsQosReliability, c3gGsmNegoGprsQosPeakRate C3gGprsQosPeakRate, c3gGsmNegoGprsQosMeanRate C3gGprsQosMeanRate } c3gGsmNegoGprsQosPrecedence OBJECT-TYPE SYNTAX C3gGprsQosPrecedence MAX-ACCESS read-only STATUS current DESCRIPTION "Negotiated GPRS QoS precedence." ::= { c3gGsmNegoGprsQosEntry 1 } c3gGsmNegoGprsQosDelay OBJECT-TYPE SYNTAX C3gGprsQosDelay MAX-ACCESS read-only STATUS current DESCRIPTION "Negotiated GPRS QoS delay classes." ::= { c3gGsmNegoGprsQosEntry 2 } c3gGsmNegoGprsQosReliability OBJECT-TYPE SYNTAX C3gGprsQosReliability MAX-ACCESS read-only STATUS current DESCRIPTION "Negotiated GPRS QoS reliability." ::= { c3gGsmNegoGprsQosEntry 3 } c3gGsmNegoGprsQosPeakRate OBJECT-TYPE SYNTAX C3gGprsQosPeakRate MAX-ACCESS read-only STATUS current DESCRIPTION "Negotiated GPRS QoS peak rate." ::= { c3gGsmNegoGprsQosEntry 4 } c3gGsmNegoGprsQosMeanRate OBJECT-TYPE SYNTAX C3gGprsQosMeanRate UNITS "octet-per-hour" MAX-ACCESS read-only STATUS current DESCRIPTION "Negotiated GPRS QoS mean rate." ::= { c3gGsmNegoGprsQosEntry 5 } c3gGsmRadio OBJECT IDENTIFIER ::= { c3gWanGsm 4 } c3gGsmRadioTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gGsmRadioEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Cellular 3G GSM/4G-LTE radio table." ::= { c3gGsmRadio 1 } c3gGsmRadioEntry OBJECT-TYPE SYNTAX C3gGsmRadioEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the c3gGsmRadioTable." INDEX { entPhysicalIndex } ::= { c3gGsmRadioTable 1 } C3gGsmRadioEntry ::= SEQUENCE { c3gCurrentGsmRssi C3gRssi, c3gCurrentGsmEcIo C3gEcIo, c3gGsmCurrentBand INTEGER, c3gGsmChannelNumber Unsigned32, c3gGsmNumberOfNearbyCell Unsigned32 } c3gCurrentGsmRssi OBJECT-TYPE SYNTAX C3gRssi MAX-ACCESS read-only STATUS current DESCRIPTION "The GPRS/UMTS/LTE RSSI value." ::= { c3gGsmRadioEntry 1 } c3gCurrentGsmEcIo OBJECT-TYPE SYNTAX C3gEcIo MAX-ACCESS read-only STATUS current DESCRIPTION "The GPRS, UMTS or LTE Ec/Io value." ::= { c3gGsmRadioEntry 2 } c3gGsmCurrentBand OBJECT-TYPE SYNTAX INTEGER { unknown(1), invalid(2), none(3), gsm850(4), gsm900(5), gsm1800(6), gsm1900(7), wcdma800(8), wcdma850(9), wcdma1900(10), wcdma2100(11), lteBand(12) } MAX-ACCESS read-only STATUS current DESCRIPTION "GPRS/UMTS/LTE band to which the modem is attached. Refer CISCO-WAN-CELL-EXT-MIB for LTE band number when in LTE mode." DEFVAL { unknown } ::= { c3gGsmRadioEntry 3 } c3gGsmChannelNumber OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Channel number to which the modem is attached. This is only applicable in 3G technology mode. Refer CISCO-WAN-CELL-EXT-MIB for the LTE uplink and downlink channel values" DEFVAL { 0 } ::= { c3gGsmRadioEntry 4 } c3gGsmNumberOfNearbyCell OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the current total number of nearby cell in the c3gGsmNearbyCellTable. User can poll this object to get the total number of nearby cell before polling c3gGsmNearbyCellTable." DEFVAL { 0 } ::= { c3gGsmRadioEntry 5 } c3gGsmNearbyCellTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gGsmNearbyCellEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Cellular GSM/4G-LTE nearby cell table. Object c3gGsmNumberOfNearbyCell indicates the total number of nearby cell in this table." ::= { c3gGsmRadio 2 } c3gGsmNearbyCellEntry OBJECT-TYPE SYNTAX C3gGsmNearbyCellEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the c3gGsmNearbyCellTable." INDEX { entPhysicalIndex, c3gGsmNearbyCellIndex } ::= { c3gGsmNearbyCellTable 1 } C3gGsmNearbyCellEntry ::= SEQUENCE { c3gGsmNearbyCellIndex Integer32, c3gGsmNearbyCellPrimaryScramblingCode Unsigned32, c3gGsmNearbyCellRscp Integer32, c3gGsmNearbyCellEcIoMeasurement C3gEcIo } c3gGsmNearbyCellIndex OBJECT-TYPE SYNTAX Integer32 (1..100) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Nearby cell index, combined with entPhysicalIndex to access the Nearby cell table c3gGsmNearbyCellTable." ::= { c3gGsmNearbyCellEntry 1 } c3gGsmNearbyCellPrimaryScramblingCode OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Nearby cell primary scrambling code." ::= { c3gGsmNearbyCellEntry 2 } c3gGsmNearbyCellRscp OBJECT-TYPE SYNTAX Integer32 (-150..0) UNITS "dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Nearby cell Received Signal Code Power (RSCP)." ::= { c3gGsmNearbyCellEntry 3 } c3gGsmNearbyCellEcIoMeasurement OBJECT-TYPE SYNTAX C3gEcIo UNITS "dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Nearby cell Ec/Io measurement." ::= { c3gGsmNearbyCellEntry 4 } c3gGsmHistoryTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gGsmHistoryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Cellular 3G GSM/4G-LTE RSSI history table. The history of RSSI are carried in an octet of string. Each octet in the octet string has a value from 0 to 150 and the 255 value is reserved to indicate an uninitialized (Invalid) value. The format of the octet string with n octets is as following: [ octet 0 is latest, octet 1 is latest-1, . . octet n-2 is oldest-1, octet n-1 is oldest ] To convert the provided value into dBm the following formula should be used: dBm = (-1)*value;" ::= { c3gGsmRadio 3 } c3gGsmHistoryEntry OBJECT-TYPE SYNTAX C3gGsmHistoryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the c3gGsmHistoryTable." INDEX { entPhysicalIndex } ::= { c3gGsmHistoryTable 1 } C3gGsmHistoryEntry ::= SEQUENCE { c3gGsmHistoryRssiPerSecond OCTET STRING, c3gGsmHistoryRssiPerMinute OCTET STRING, c3gGsmHistoryRssiPerHour OCTET STRING } c3gGsmHistoryRssiPerSecond OBJECT-TYPE SYNTAX OCTET STRING (SIZE (60)) UNITS "-dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Per-second RSSI history. This object contains a per-second history of RSSI values for the last 60 seconds." ::= { c3gGsmHistoryEntry 1 } c3gGsmHistoryRssiPerMinute OBJECT-TYPE SYNTAX OCTET STRING (SIZE (60)) UNITS "-dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Per-minute weakest RSSI value history. This object contains a per-minute history of weakest RSSI values for the last 60 minutes. The octet in the string is the weakest RSSI value measured in a minute interval." ::= { c3gGsmHistoryEntry 2 } c3gGsmHistoryRssiPerHour OBJECT-TYPE SYNTAX OCTET STRING (SIZE (72)) UNITS "-dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Per-hour weakest RSSI value history. This object contains a per-hour history of weakest RSSI values for the last 72 hours. The octet in the string is the weakest RSSI value measured in an hour interval." ::= { c3gGsmHistoryEntry 3 } c3gGsmSecurity OBJECT IDENTIFIER ::= { c3gWanGsm 5 } c3gGsmSecurityTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gGsmSecurityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Cellular 3G GSM/4G-LTE security table." ::= { c3gGsmSecurity 1 } c3gGsmSecurityEntry OBJECT-TYPE SYNTAX C3gGsmSecurityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the c3gGsmSecurityTable." INDEX { entPhysicalIndex } ::= { c3gGsmSecurityTable 1 } C3gGsmSecurityEntry ::= SEQUENCE { c3gGsmChv1 INTEGER, c3gGsmSimStatus INTEGER, c3gGsmSimUserOperationRequired INTEGER, c3gGsmNumberOfRetriesRemaining Unsigned32 } c3gGsmChv1 OBJECT-TYPE SYNTAX INTEGER { unknown(1), disabled(2), enabled(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Card Holder Verification 1 (CHV1), if enabled, the PIN will be verified, if disabled, the PIN will not be verified." DEFVAL { disabled } ::= { c3gGsmSecurityEntry 1 } c3gGsmSimStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), ok(2), notInserted(3), removed(4), initFailure(5), generalFailure(6), locked(7), chv1Blocked(8), chv2Blocked(9), chv1Rejected(10), chv2Rejected(11), mepLocked(12), networkRejected(13) } MAX-ACCESS read-only STATUS current DESCRIPTION "SIM status. Indicates whether the SIM is present or removed from the SIM socket, and its current status." DEFVAL { unknown } ::= { c3gGsmSecurityEntry 2 } c3gGsmSimUserOperationRequired OBJECT-TYPE SYNTAX INTEGER { unknown(1), none(2), enterChv1(3), enterChv2(4), enterUnblockChv1(5), enterUnblockChv2(6), enterMepCode(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "If the SIM is protected (for example, because of CHV1 enabled), it will indicate the type of user operation required." DEFVAL { unknown } ::= { c3gGsmSecurityEntry 3 } c3gGsmNumberOfRetriesRemaining OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the number of attempts remaining in case the SIM is locked. If the number of retries becomes zero, the SIM is blocked and becomes unusable." DEFVAL { 0 } ::= { c3gGsmSecurityEntry 4 } c3gWanLbsCommon OBJECT IDENTIFIER ::= { c3gWanLbs 1 } c3gWanLbsCommonTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gWanLbsCommonEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information about the Cellular Location Based service feature. This GPS data is provided by the wireless modem upon GPS configuration." ::= { c3gWanLbsCommon 1 } c3gWanLbsCommonEntry OBJECT-TYPE SYNTAX C3gWanLbsCommonEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry contains information about the Cellular Location Based service variables returned by the wireless modem." INDEX { entPhysicalIndex } ::= { c3gWanLbsCommonTable 1 } C3gWanLbsCommonEntry ::= SEQUENCE { c3gLbsModeSelected INTEGER, c3gLbsState INTEGER, c3gLbsLocFixError INTEGER, c3gLbsLatitude SnmpAdminString, c3gLbsLongitude SnmpAdminString, c3gLbsTimeStamp SnmpAdminString, c3gLbsLocUncertaintyAngle Unsigned32, c3gLbsLocUncertaintyA Unsigned32, c3gLbsLocUncertaintyPos Unsigned32, c3gLbsFixtype INTEGER, c3gLbsHeightValid TruthValue, c3gLbsHeight Integer32, c3gLbsLocUncertaintyVertical Unsigned32, c3gLbsVelocityValid TruthValue, c3gLbsHeading Unsigned32, c3gLbsVelocityHorizontal Unsigned32, c3gLbsVelocityVertical Unsigned32, c3gLbsHepe Unsigned32, c3gLbsNumSatellites Gauge32 } c3gLbsModeSelected OBJECT-TYPE SYNTAX INTEGER { unKnown(1), standAlone(2), msBased(3), msAssist(4), reserved(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Mode of Location base service selected. unKnown - mode selection unkown standAlone - Standalone mode msBased - MS-Based mode msAssist - MS-Assist mode reserved - reserved for future use" DEFVAL { unKnown } ::= { c3gWanLbsCommonEntry 1 } c3gLbsState OBJECT-TYPE SYNTAX INTEGER { gpsDisabled(1), gpsAcquiring(2), gpsEnabled(3), gpsLocError(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Location base service state. gpsDisabled - GPS is disabled gpsEnabled - GPS is enabled gpsLocError - GPS encounters error gpsAcquiring - GPS is acquiring fix" DEFVAL { gpsDisabled } ::= { c3gWanLbsCommonEntry 2 } c3gLbsLocFixError OBJECT-TYPE SYNTAX INTEGER { offline(1), noService(2), noConnection(3), noData(4), sessionBusy(5), reserved(6), gpsDisabled(7), connectionFailed(8), errorState(9), clientEnded(10), uiEnded(11), networkEnded(12), timeout(13), privacyLevel(14), networkAccessError(15), fixError(16), pdeRejected(17), trafficChannelExited(18), e911(19), serverError(20), staleBSinformation(21), resourceContention(22), authenticationParameterFailed(23), authenticationFailedLocal(24), authenticationFailedNetwork(25), vxLcsAgentAuthFail(26), unknownSystemError(27), unsupportedService(28), subscriptionViolation(29), desiredFixMethodFailed(30), antennaSwitch(31), noTxConfirmationReceived(32), normalEndOfSession(33), noErrorFromNetwork(34), noResourcesLeftOnNetwork(35), positionServerNotAvailable(36), unsupportedProtocolVersion(37), ssmolrErrorSystemFailure(38), ssmolrErrorUnexpectedDataValue(39), ssmolrErrorDataMissing(40), ssmolrErrorFacilityNotSupported(41), ssmolrErrorSsSubscriptionViolation(42), ssmolrErrorPositionMethodFailure(43), ssmolrErrorUndefined(44), smlcTimeout(45), mtGguardTimeExpired(46), additionalAssistanceNeeded(47), noFixError(48) } MAX-ACCESS read-only STATUS current DESCRIPTION "Location base service fix error code." REFERENCE "Refer to the following documents for the error code's full definitions. Sierra Wireless CDMA EVDO CnS Reference_1.2.pdf under Location Based Services section." DEFVAL { noFixError } ::= { c3gWanLbsCommonEntry 3 } c3gLbsLatitude OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Location base service Latitude." ::= { c3gWanLbsCommonEntry 4 } c3gLbsLongitude OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Location base service longitude." ::= { c3gWanLbsCommonEntry 5 } c3gLbsTimeStamp OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Location base service timestamp." ::= { c3gWanLbsCommonEntry 6 } c3gLbsLocUncertaintyAngle OBJECT-TYPE SYNTAX Unsigned32 UNITS "degrees" MAX-ACCESS read-only STATUS current DESCRIPTION "GPS Uncertainty parameter Angle, in degrees for the Uncertainty info returned by the GPS device while doing a location fix." DEFVAL { 0 } ::= { c3gWanLbsCommonEntry 7 } c3gLbsLocUncertaintyA OBJECT-TYPE SYNTAX Unsigned32 UNITS "meters" MAX-ACCESS read-only STATUS current DESCRIPTION "GPS Uncertainty parameter A, value in meters for the Uncertainty info returned by the GPS device while doing a location fix." DEFVAL { 0 } ::= { c3gWanLbsCommonEntry 8 } c3gLbsLocUncertaintyPos OBJECT-TYPE SYNTAX Unsigned32 UNITS "meters" MAX-ACCESS read-only STATUS current DESCRIPTION "GPS Uncertainty parameter position, value in meters for the Uncertainty info returned by the GPS device while doing a location fix." DEFVAL { 0 } ::= { c3gWanLbsCommonEntry 9 } c3gLbsFixtype OBJECT-TYPE SYNTAX INTEGER { none(1), twoDimension(2), threeDimension(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of location fix in Location Base service. none - default case, while LBS is not enabled. twoDimension - 2D location fix. threeDimension - 3D location fix." DEFVAL { none } ::= { c3gWanLbsCommonEntry 10 } c3gLbsHeightValid OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether the height returned by the GPS device is valid during location fix." DEFVAL { false } ::= { c3gWanLbsCommonEntry 11 } c3gLbsHeight OBJECT-TYPE SYNTAX Integer32 (-500..500) UNITS "meters" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the GPS height parameter returned by the GPS device while performing location fix." DEFVAL { 0 } ::= { c3gWanLbsCommonEntry 12 } c3gLbsLocUncertaintyVertical OBJECT-TYPE SYNTAX Unsigned32 UNITS "meters" MAX-ACCESS read-only STATUS current DESCRIPTION "GPS parameter vertical velocity parameter returned by the GPS device while performing location fix." DEFVAL { 0 } ::= { c3gWanLbsCommonEntry 13 } c3gLbsVelocityValid OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether the Velocity value returned by the GPS device is valid." DEFVAL { false } ::= { c3gWanLbsCommonEntry 14 } c3gLbsHeading OBJECT-TYPE SYNTAX Unsigned32 UNITS "degrees" MAX-ACCESS read-only STATUS current DESCRIPTION "The compass direction toward which the GPS receiver is (or should be) moving." DEFVAL { 0 } ::= { c3gWanLbsCommonEntry 15 } c3gLbsVelocityHorizontal OBJECT-TYPE SYNTAX Unsigned32 UNITS "meters per second" MAX-ACCESS read-only STATUS current DESCRIPTION "Horizontal Velocity in meters per second the GPS device is heading. This is the value returned by the GPS satellite relative to the last horizontal location of the GPS device. If at Time X satellite sees the location of GPS device is L1 and then at Time Y satellite sees the location is L2 then speed is (L2 - L1) / ( Y - X)." DEFVAL { 0 } ::= { c3gWanLbsCommonEntry 16 } c3gLbsVelocityVertical OBJECT-TYPE SYNTAX Unsigned32 UNITS "meters per second" MAX-ACCESS read-only STATUS current DESCRIPTION "Vertical Velocity in meters per second the GPS device is heading. This is the value returned by the GPS satellite relative to the last vertical location of the GPS device. If at Time X satellite sees the location of GPS device is L1 and then at Time Y satellite sees the location is L2 then speed is (L2 - L1) / ( Y - X)." DEFVAL { 0 } ::= { c3gWanLbsCommonEntry 17 } c3gLbsHepe OBJECT-TYPE SYNTAX Unsigned32 UNITS "centimeters" MAX-ACCESS read-only STATUS current DESCRIPTION "Horizontal Estimated Position Error returned by the GPS satellite for current position of the GPS device." DEFVAL { 0 } ::= { c3gWanLbsCommonEntry 18 } c3gLbsNumSatellites OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of GPS satellites in vision to the modem while GPS tracking is on." DEFVAL { 0 } ::= { c3gWanLbsCommonEntry 19 } c3gWanLbsSatelliteInfo OBJECT IDENTIFIER ::= { c3gWanLbs 2 } c3gWanLbsSatelliteInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gWanLbsSatelliteInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides information on each satellite that is visible to the modem during the location fix. These satellites guide the device to acquire a 2D or 3D location fix." ::= { c3gWanLbsSatelliteInfo 1 } c3gWanLbsSatelliteInfoEntry OBJECT-TYPE SYNTAX C3gWanLbsSatelliteInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides information about each satellite's elevation, azimuth, Signal to Noise ratio (SNR) and its reference number local to the router." INDEX { entPhysicalIndex, c3gWanLbsSatelliteInfoIndex } ::= { c3gWanLbsSatelliteInfoTable 1 } C3gWanLbsSatelliteInfoEntry ::= SEQUENCE { c3gWanLbsSatelliteInfoIndex Integer32, c3gWanLbsSatelliteNumber Integer32, c3gWanLbsSatelliteElevation Integer32, c3gWanLbsSatelliteAzimuth Integer32, c3gWanLbsSatelliteInfoSignalNoiseRatio Integer32, c3gWanLbsSatelliteUsed TruthValue, c3gWanLbsSatelliteInfoRowStatus RowStatus } c3gWanLbsSatelliteInfoIndex OBJECT-TYPE SYNTAX Integer32 (1..1000) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index that is assigned to each satellite under a modem and in combination with entPhysicalIndex uniquely identify it. This index is assigned arbitrarily by the engine and is not saved over reboots." ::= { c3gWanLbsSatelliteInfoEntry 1 } c3gWanLbsSatelliteNumber OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Each Satellite is assigned a unique number within this device.This object can be used to locate a particular satellite under a modem." REFERENCE "Refer to the following documents for detailed information of Satellites. Sierra Wireless CDMA EVDO CnS Reference_1.2.pdf under Location Based Services section" ::= { c3gWanLbsSatelliteInfoEntry 2 } c3gWanLbsSatelliteElevation OBJECT-TYPE SYNTAX Integer32 UNITS "degrees" MAX-ACCESS read-only STATUS current DESCRIPTION "Angle of Elevation between the GPS antenna pointing direction, directly towards the satellite, and the local horizontal plane. It is the up-down angle" REFERENCE "Refer to the following documents for detailed information of Satellites elevation. Sierra Wireless CDMA EVDO CnS Reference_1.2.pdf under Location Based Services section" ::= { c3gWanLbsSatelliteInfoEntry 3 } c3gWanLbsSatelliteAzimuth OBJECT-TYPE SYNTAX Integer32 UNITS "degrees" MAX-ACCESS read-only STATUS current DESCRIPTION "Azimuth of the current satellite in context referenced by the Satellite InfoIndex. Azimuth is the degree of rotation of the satellites dish on its vertical plane." REFERENCE "Refer to the following documents for detailed information of Satellites Azimuth. Sierra Wireless CDMA EVDO CnS Reference_1.2.pdf under Location Based Services section" ::= { c3gWanLbsSatelliteInfoEntry 4 } c3gWanLbsSatelliteInfoSignalNoiseRatio OBJECT-TYPE SYNTAX Integer32 UNITS "db" MAX-ACCESS read-only STATUS current DESCRIPTION "Signal to Noise Ratio(SNR) of received GPS signal. SNR is refered to as the signal strength in GPS standards." REFERENCE "Refer to the following documents for detailed information of signal to noise ration in LBS. Sierra Wireless CDMA EVDO CnS Reference_1.2.pdf under Location Based Services section" ::= { c3gWanLbsSatelliteInfoEntry 5 } c3gWanLbsSatelliteUsed OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Is this satellite in line of sight to the modem used in calculating the GPS location?" DEFVAL { false } ::= { c3gWanLbsSatelliteInfoEntry 6 } c3gWanLbsSatelliteInfoRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. This object is used to manage creation, modification and deletion of rows in this table." ::= { c3gWanLbsSatelliteInfoEntry 7 } c3gWanSms OBJECT IDENTIFIER ::= { c3gWanSmsCommon 1 } c3gSmsCommonTable OBJECT-TYPE SYNTAX SEQUENCE OF C3gSmsCommonEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains Cellular SMS management MIB objects." ::= { c3gWanSms 1 } c3gSmsCommonEntry OBJECT-TYPE SYNTAX C3gSmsCommonEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry contains counters for the SMS messages received, placed, errored and archived on CDMA, GSM or LTE based modems." INDEX { entPhysicalIndex } ::= { c3gSmsCommonTable 1 } C3gSmsCommonEntry ::= SEQUENCE { c3gSmsServiceAvailable TruthValue, c3gSmsOutSmsCount Counter32, c3gSmsOutSmsErrorCount Counter32, c3gSmsInSmsStorageUsed Gauge32, c3gSmsInSmsStorageUnused Gauge32, c3gSmsInSmsArchiveCount Gauge32, c3gSmsInSmsArchiveErrorCount Gauge32, c3gSmsArchiveUrl SnmpAdminString, c3gSmsOutSmsStatus INTEGER, c3gSmsInSmsCount Counter32, c3gSmsInSmsDeleted Counter32, c3gSmsInSmsStorageMax Counter64, c3gSmsInSmsCallBack Counter32, c3gSmsOutSmsPendingCount Gauge32, c3gSmsOutSmsArchiveCount Gauge32, c3gSmsOutSmsArchiveErrorCount Gauge32, c3gSmsInSmsArchived Gauge32 } c3gSmsServiceAvailable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the availability of SMS Service." DEFVAL { false } ::= { c3gSmsCommonEntry 1 } c3gSmsOutSmsCount OBJECT-TYPE SYNTAX Counter32 UNITS "msgs" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of SMS messages which have been sent successfully." ::= { c3gSmsCommonEntry 2 } c3gSmsOutSmsErrorCount OBJECT-TYPE SYNTAX Counter32 UNITS "msgs" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of SMS message that could not be sent." ::= { c3gSmsCommonEntry 3 } c3gSmsInSmsStorageUsed OBJECT-TYPE SYNTAX Gauge32 UNITS "msgs" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of SMS message records space used in the Incoming SMS message storage. One standard SMS message (cdma or gsm) occupies 1 unit of record storage space. A big SMS message can span 'n' sms record space but still be called as 1 SMS message. Storage used can be greater than or equal to total number of Incoming SMS received." ::= { c3gSmsCommonEntry 4 } c3gSmsInSmsStorageUnused OBJECT-TYPE SYNTAX Gauge32 UNITS "msgs" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of SMS messages record space left unused in the Incoming SMS message storage. This is equal to c3gSmsInSmsStorageMax - c3gSmsInSmsStorageUsed." ::= { c3gSmsCommonEntry 5 } c3gSmsInSmsArchiveCount OBJECT-TYPE SYNTAX Gauge32 UNITS "msgs" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of successful archive of Incoming SMS messages since router reload. Each SMS message occupies x bytes of space. So if the incoming message is huge, then it is archived as multiple of x bytes but still called as one SMS message. This is the difference between c3gSmsInSmsArchiveCount and c3gSmsInSmsArchived." ::= { c3gSmsCommonEntry 6 } c3gSmsInSmsArchiveErrorCount OBJECT-TYPE SYNTAX Gauge32 UNITS "msgs" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Incoming SMS messages that could not be archived since device was reloaded." ::= { c3gSmsCommonEntry 7 } c3gSmsArchiveUrl OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "URL of the sms archive directory on the ftp server. The url will be of this format ftp://x.y.z.k/user/dirname" ::= { c3gSmsCommonEntry 8 } c3gSmsOutSmsStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), success(2), copySmsHeader(3), copySmsBody(4), sent(5), receivedSentNotification(6), receivedOutMsgNumber(7), receivedOutMsgStatus(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "Status of the last send operation of outgoing SMS message to the network." ::= { c3gSmsCommonEntry 9 } c3gSmsInSmsCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of SMS messages which have been received successfully and stored in router. These SMS's are a mirror copy of SMS stored in Modem or SIM" ::= { c3gSmsCommonEntry 10 } c3gSmsInSmsDeleted OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of SMS messages which have been deleted since router boot up. This does not include SMS messages that are already archived." ::= { c3gSmsCommonEntry 11 } c3gSmsInSmsStorageMax OBJECT-TYPE SYNTAX Counter64 UNITS "msgs" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of SMS message records space allocated in the router's DRAM to store Incoming SMS messages." ::= { c3gSmsCommonEntry 12 } c3gSmsInSmsCallBack OBJECT-TYPE SYNTAX Counter32 UNITS "msgs" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of incoming SMS messages that triggered callback." ::= { c3gSmsCommonEntry 13 } c3gSmsOutSmsPendingCount OBJECT-TYPE SYNTAX Gauge32 UNITS "msgs" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of outgoing SMS messages that are in pending queue of the router." ::= { c3gSmsCommonEntry 14 } c3gSmsOutSmsArchiveCount OBJECT-TYPE SYNTAX Gauge32 UNITS "msgs" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of successfull archive of outgoing SMS messages since router reload." ::= { c3gSmsCommonEntry 15 } c3gSmsOutSmsArchiveErrorCount OBJECT-TYPE SYNTAX Gauge32 UNITS "msgs" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of failed archive of outgoing SMS messages since router reload." ::= { c3gSmsCommonEntry 16 } c3gSmsInSmsArchived OBJECT-TYPE SYNTAX Gauge32 UNITS "msgs" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of Incoming SMS messages that are successfully archived since router reload." ::= { c3gSmsCommonEntry 17 } -- Default Notification Type c3gModemUpNotif NOTIFICATION-TYPE OBJECTS { entPhysicalName } STATUS current DESCRIPTION "This is the notification that the modem has been detected by host interface. Users can enable or disable the generation of this notification by using object c3gModemUpNotifEnabled." ::= { ciscoWan3gMIBNotifs 1 } c3gModemDownNotif NOTIFICATION-TYPE OBJECTS { entPhysicalName } STATUS current DESCRIPTION "This is the notification that the modem has not been detected by host interface, or has been disconnected from host interface. Users can enable or disable the generation of this notification by using object c3gModemDownNotifEnabled." ::= { ciscoWan3gMIBNotifs 2 } c3gServiceChangedNotif NOTIFICATION-TYPE OBJECTS { c3gPreviousServiceType, c3gCurrentServiceType } STATUS current DESCRIPTION "Notification for service change event. Objects c3gPreviousServiceType and c3gCurrentServiceType will be included in the notification. Users can enable or disable the generation of this notification by using object c3gServiceChangedNotifEnabled." ::= { ciscoWan3gMIBNotifs 3 } c3gNetworkChangedNotif NOTIFICATION-TYPE OBJECTS { c3gCurrentSid, c3gCurrentNid, c3gGsmMcc, c3gGsmMnc, c3gRoamingStatus } STATUS current DESCRIPTION "Notification for network change event. Objects c3gCurrentSid, c3gCurrentNid, c3gGsmMcc, c3gGsmMnc and c3gRoamingStatus will be included in the notification. Users can enable or disable the generation of this notification by using object c3gNetworkChangedNotifEnabled." ::= { ciscoWan3gMIBNotifs 4 } c3gConnectionStatusChangedNotif NOTIFICATION-TYPE OBJECTS { c3gConnectionStatus, c3gCurrentServiceType } STATUS current DESCRIPTION "Notification for connection status change event. Objects c3gConnectionStatus and c3gCurrentServiceType will be included in the notification. Users can use object c3gConnectionStatusChangedNotifFlag to control what connection status changes will cause the generation of this notification." ::= { ciscoWan3gMIBNotifs 5 } c3gRssiOnsetNotif NOTIFICATION-TYPE OBJECTS { c3gNotifRadioService, c3gNotifRssi } STATUS current DESCRIPTION "If RSSI goes below c3gRssiOnsetNotifThreshold and the service bit in c3gRssiOnsetNotifFlag is set, this notification will be generated. Object c3gNotifRadioService will indicate which service generates this notification and the associated RSSI will be reported in c3gNotifRssi. Please note that c3gNotifRssi is used to indicate the RSSI value that triggers the notification, user should go to the corresponding radio table to get the current RSSI value." ::= { ciscoWan3gMIBNotifs 6 } c3gRssiAbateNotif NOTIFICATION-TYPE OBJECTS { c3gNotifRadioService, c3gNotifRssi } STATUS current DESCRIPTION "If RSSI goes above c3gRssiAbateNotifThreshold and the service bit in c3gRssiAbateNotifFlag is set, this notification will be generated. Object c3gNotifRadioService will indicate which service generates this notification and the associated RSSI will be reported in c3gNotifRssi. Please note that c3gNotifRssi is used to indicate the RSSI value that triggers the notification, user should go to the corresponding radio table to get the current RSSI value." ::= { ciscoWan3gMIBNotifs 7 } c3gEcIoOnsetNotif NOTIFICATION-TYPE OBJECTS { c3gNotifRadioService, c3gNotifEcIo } STATUS current DESCRIPTION "If Ec/Io goes below c3gEcIoOnsetNotifThreshold and the service bit in c3gEcIoOnsetNotifFlag is set, this notification will be generated. Object c3gNotifRadioService will indicate which service generates this notification and the associated Ec/Io will be reported in c3gNotifEcIo. Please note that c3gNotifEcIo is used to indicate the Ec/Io value that triggers the notification, user should go to the corresponding radio table to get the current Ec/Io value." ::= { ciscoWan3gMIBNotifs 8 } c3gEcIoAbateNotif NOTIFICATION-TYPE OBJECTS { c3gNotifRadioService, c3gNotifEcIo } STATUS current DESCRIPTION "If Ec/Io goes above c3gEcIoAbateNotifThreshold and the service bit in c3gEcIoAbateNotifFlag is set, this notification will be generated. Object c3gNotifRadioService will indicate which service generates this notification and the associated Ec/Io will be reported in c3gNotifEcIo. Please note that c3gNotifEcIo is used to indicate the Ec/Io value that triggers the notification, user should go to the corresponding radio table to get the current Ec/Io value." ::= { ciscoWan3gMIBNotifs 9 } c3gModemTemperOnsetNotif NOTIFICATION-TYPE OBJECTS { c3gModemTemperature } STATUS current DESCRIPTION "If modem temperature goes above c3gModemTemperOnsetNotifThreshold and the value of c3gModemTemperOnsetNotifEnabled is 'true', this notification will be generated and the current value of c3gModemTemperature will be included in this notification." ::= { ciscoWan3gMIBNotifs 10 } c3gModemTemperAbateNotif NOTIFICATION-TYPE OBJECTS { c3gModemTemperature } STATUS current DESCRIPTION "If modem temperature goes below c3gModemTemperAbateNotifThreshold and the value of c3gModemTemperAbateNotifEnabled is 'true', this notification will be generated and the current value of c3gModemTemperature will be included in this notification." ::= { ciscoWan3gMIBNotifs 11 } c3gModemTemperOnsetRecoveryNotif NOTIFICATION-TYPE OBJECTS { c3gModemTemperature } STATUS current DESCRIPTION "This trap is generated as a recovery notification for c3gModemTemperOnsetNotif.This trap is generated when the current value of c3gModemTemperature goes below c3gModemTemperOnsetNotifThreshold once it has generated the c3gModemTemperOnsetNotif and the value of c3gModemTemperOnsetNotifEnabled is 'true'. c3gModemTemperature contains the current value of modem temperature." ::= { ciscoWan3gMIBNotifs 12 } c3gModemTemperAbateRecoveryNotif NOTIFICATION-TYPE OBJECTS { c3gModemTemperature } STATUS current DESCRIPTION "This trap is generated as a recovery notification for c3gModemTemperAbateNotif.This trap is generated when the current value of c3gModemTemperature goes above c3gModemTemperAbateNotifThreshold once it has generated the c3gModemTemperAbateNotif and the value of c3gModemTemperAbateNotifEnabled is 'true' c3gModemTemperature contains the current value of modem temperature" ::= { ciscoWan3gMIBNotifs 13 } -- Conformance ciscoWan3gMIBCompliances OBJECT IDENTIFIER ::= { ciscoWan3gMIBConform 1 } ciscoWan3gMIBGroups OBJECT IDENTIFIER ::= { ciscoWan3gMIBConform 2 } ciscoWan3gMIBCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "This is a default module-compliance containing default object groups." MODULE -- this module MANDATORY-GROUPS { ciscoWan3gMIBNotificationGroup, ciscoWan3gMIBCommonObjectGroup } GROUP ciscoWan3gMIBCdmaObjectGroup DESCRIPTION "This object group should be included for CDMA standard." GROUP ciscoWan3gMIBGsmObjectGroup DESCRIPTION "This object group should be included for GSM/LTE standard." GROUP ciscoWan3gMIBSmsObjectGroup DESCRIPTION "This object group should be included for SMS service on CDMA, GSM and LTE standard." GROUP ciscoWan3gMIBLbsObjectGroup DESCRIPTION "This object group should be included for Location based service on CDMA, GSM and LTE standard." ::= { ciscoWan3gMIBCompliances 1 } ciscoWan3gMIBCompliance1 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the CISCO-WAN-3G-MIB." MODULE -- this module MANDATORY-GROUPS { ciscoWan3gMIBNotificationGroup, ciscoWan3gMIBCommonObjectGroup } GROUP ciscoWan3gMIBCdmaObjectGroup DESCRIPTION "This object group should be included for CDMA standard." GROUP ciscoWan3gMIBGsmObjectGroup DESCRIPTION "This object group should be included for GSM and LTE standard." GROUP ciscoWan3gMIBSmsObjectGroup DESCRIPTION "This object group should be included for SMS service on CDMA, GSM and LTE standard." GROUP ciscoWan3gMIBLbsObjectGroup DESCRIPTION "This object group should be included for Location based service on CDMA, GSM and LTE standard." ::= { ciscoWan3gMIBCompliances 2 } ciscoWan3gMIBComplianceRev1 MODULE-COMPLIANCE STATUS current DESCRIPTION "This is a default module-compliance containing default object groups." MODULE -- this module MANDATORY-GROUPS { ciscoWan3gMIBNotificationGroupRev1, ciscoWan3gMIBCommonObjectGroup } GROUP ciscoWan3gMIBCdmaObjectGroup DESCRIPTION "This object group should be included for CDMA standard." GROUP ciscoWan3gMIBGsmObjectGroup DESCRIPTION "This object group should be included for GSM/LTE standard." GROUP ciscoWan3gMIBSmsObjectGroup DESCRIPTION "This object group should be included for SMS service on CDMA, GSM and LTE standard." GROUP ciscoWan3gMIBLbsObjectGroup DESCRIPTION "This object group should be included for Location based service on CDMA, GSM and LTE standard." ::= { ciscoWan3gMIBCompliances 3 } ciscoWan3gMIBCompliance1Rev1 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for the CISCO-WAN-3G-MIB." MODULE -- this module MANDATORY-GROUPS { ciscoWan3gMIBNotificationGroupRev1, ciscoWan3gMIBCommonObjectGroup } GROUP ciscoWan3gMIBCdmaObjectGroup DESCRIPTION "This object group should be included for CDMA standard." GROUP ciscoWan3gMIBGsmObjectGroup DESCRIPTION "This object group should be included for GSM and LTE standard." GROUP ciscoWan3gMIBSmsObjectGroup DESCRIPTION "This object group should be included for SMS service on CDMA, GSM and LTE standard." GROUP ciscoWan3gMIBLbsObjectGroup DESCRIPTION "This object group should be included for Location based service on CDMA, GSM and LTE standard." ::= { ciscoWan3gMIBCompliances 4 } -- Units of Conformance ciscoWan3gMIBCommonObjectGroup OBJECT-GROUP OBJECTS { c3gStandard, c3gCapability, c3gModemState, c3gPreviousServiceType, c3gCurrentServiceType, c3gRoamingStatus, c3gCurrentSystemTime, c3gConnectionStatus, c3gNotifRadioService, c3gNotifRssi, c3gNotifEcIo, c3gModemTemperature, c3gRssiOnsetNotifThreshold, c3gRssiAbateNotifThreshold, c3gEcIoOnsetNotifThreshold, c3gEcIoAbateNotifThreshold, c3gModemTemperOnsetNotifThreshold, c3gModemTemperAbateNotifThreshold, c3gModemReset, c3gModemUpNotifEnabled, c3gModemDownNotifEnabled, c3gServiceChangedNotifEnabled, c3gNetworkChangedNotifEnabled, c3gConnectionStatusChangedNotifFlag, c3gRssiOnsetNotifFlag, c3gRssiAbateNotifFlag, c3gEcIoOnsetNotifFlag, c3gEcIoAbateNotifFlag, c3gModemTemperOnsetNotifEnabled, c3gModemTemperAbateNotifEnabled, c3gGpsState } STATUS current DESCRIPTION "A collection of common objects for Cellular interface." ::= { ciscoWan3gMIBGroups 1 } ciscoWan3gMIBCdmaObjectGroup OBJECT-GROUP OBJECTS { c3gCdmaTotalCallDuration, c3gCdmaTotalTransmitted, c3gCdmaTotalReceived, c3gHdrDdtmPreference, c3gOutgoingCallNumber, c3gHdrAtState, c3gHdrSessionState, c3gUati, c3gColorCode, c3gRati, c3gHdrSessionDuration, c3gHdrSessionStart, c3gHdrSessionEnd, c3gAuthStatus, c3gHdrDrc, c3gHdrDrcCover, c3gHdrRri, c3gCdmaCurrentTransmitted, c3gCdmaCurrentReceived, c3gCdmaCurrentCallStatus, c3gCdmaCurrentCallDuration, c3gCdmaCurrentCallType, c3gCdmaLastCallDisconnReason, c3gCdmaLastConnError, c3gMobileIpErrorCode, c3gEsn, c3gModemActivationStatus, c3gAccountActivationDate, c3gCdmaRoamingPreference, c3gPrlVersion, c3gMdn, c3gMsid, c3gMsl, c3gCdmaCurrentServiceStatus, c3gCdmaHybridModePreference, c3gCdmaCurrentRoamingStatus, c3gCurrentIdleDigitalMode, c3gCurrentSid, c3gCurrentNid, c3gCurrentCallSetupMode, c3gSipUsername, c3gSipPassword, c3gServingBaseStationLongitude, c3gServingBaseStationLatitude, c3gNumberOfDataProfileConfigurable, c3gCurrentActiveDataProfile, c3gNai, c3gAaaPassword, c3gMnHaSs, c3gMnHaSpi, c3gMnAaaSs, c3gMnAaaSpi, c3gReverseTunnelPreference, c3gHomeAddrType, c3gHomeAddr, c3gPriHaAddrType, c3gPriHaAddr, c3gSecHaAddrType, c3gSecHaAddr, c3gCurrent1xRttRssi, c3gCurrent1xRttEcIo, c3gCurrent1xRttChannelNumber, c3gCurrent1xRttChannelState, c3gCurrentEvDoRssi, c3gCurrentEvDoEcIo, c3gCurrentEvDoChannelNumber, c3gSectorId, c3gSubnetMask, c3gHdrColorCode, c3gPnOffset, c3gRxMainGainControl, c3gRxDiversityGainControl, c3gTxTotalPower, c3gTxGainAdjust, c3gCarrierToInterferenceRatio, c3g1xRttBandClass, c3gEvDoBandClass, c3gCdmaHistory1xRttRssiPerSecond, c3gCdmaHistory1xRttRssiPerMinute, c3gCdmaHistory1xRttRssiPerHour, c3gCdmaHistoryEvDoRssiPerSecond, c3gCdmaHistoryEvDoRssiPerMinute, c3gCdmaHistoryEvDoRssiPerHour, c3gCdmaPinSecurityStatus, c3gCdmaPowerUpLockStatus } STATUS current DESCRIPTION "A collection of objects for Cellular 3G CDMA." ::= { ciscoWan3gMIBGroups 2 } ciscoWan3gMIBGsmObjectGroup OBJECT-GROUP OBJECTS { c3gGsmTotalByteTransmitted, c3gGsmTotalByteReceived, c3gGsmPacketSessionStatus, c3gGsmPdpType, c3gGsmPdpAddress, c3gGsmNegoUmtsQosTrafficClass, c3gGsmNegoUmtsQosMaxUpLinkBitRate, c3gGsmNegoUmtsQosMaxDownLinkBitRate, c3gGsmNegoUmtsQosGuaUpLinkBitRate, c3gGsmNegoUmtsQosGuaDownLinkBitRate, c3gGsmNegoUmtsQosOrder, c3gGsmNegoUmtsQosErroneousSdu, c3gGsmNegoUmtsQosMaxSduSize, c3gGsmNegoUmtsQosSer, c3gGsmNegoUmtsQosBer, c3gGsmNegoUmtsQosDelay, c3gGsmNegoUmtsQosPriority, c3gGsmNegoUmtsQosSrcStatDescriptor, c3gGsmNegoUmtsQosSignalIndication, c3gGsmNegoGprsQosPrecedence, c3gGsmNegoGprsQosDelay, c3gGsmNegoGprsQosReliability, c3gGsmNegoGprsQosPeakRate, c3gGsmNegoGprsQosMeanRate, c3gImsi, c3gImei, c3gIccId, c3gMsisdn, c3gFsn, c3gModemStatus, c3gGsmRoamingPreference, c3gGsmLac, c3gGsmCurrentServiceStatus, c3gGsmCurrentServiceError, c3gGsmCurrentService, c3gGsmPacketService, c3gGsmCurrentRoamingStatus, c3gGsmNetworkSelectionMode, c3gGsmCountry, c3gGsmNetwork, c3gGsmMcc, c3gGsmMnc, c3gGsmRac, c3gGsmCurrentCellId, c3gGsmCurrentPrimaryScramblingCode, c3gGsmPlmnSelection, c3gGsmRegPlmn, c3gGsmPlmnAbbr, c3gGsmServiceProvider, c3gGsmPdpProfileType, c3gGsmPdpProfileAddr, c3gGsmPdpProfileApn, c3gGsmPdpProfileAuthenType, c3gGsmPdpProfileUsername, c3gGsmPdpProfilePassword, c3gGsmPdpProfileRowStatus, c3gGsmReqUmtsQosTrafficClass, c3gGsmReqUmtsQosMaxUpLinkBitRate, c3gGsmReqUmtsQosMaxDownLinkBitRate, c3gGsmReqUmtsQosGuaUpLinkBitRate, c3gGsmReqUmtsQosGuaDownLinkBitRate, c3gGsmReqUmtsQosOrder, c3gGsmReqUmtsQosErroneousSdu, c3gGsmReqUmtsQosMaxSduSize, c3gGsmReqUmtsQosSer, c3gGsmReqUmtsQosBer, c3gGsmReqUmtsQosDelay, c3gGsmReqUmtsQosPriority, c3gGsmReqUmtsQosSrcStatDescriptor, c3gGsmReqUmtsQosSignalIndication, c3gGsmReqUmtsQosRowStatus, c3gGsmMinUmtsQosTrafficClass, c3gGsmMinUmtsQosMaxUpLinkBitRate, c3gGsmMinUmtsQosMaxDownLinkBitRate, c3gGsmMinUmtsQosGuaUpLinkBitRate, c3gGsmMinUmtsQosGuaDownLinkBitRate, c3gGsmMinUmtsQosOrder, c3gGsmMinUmtsQosErroneousSdu, c3gGsmMinUmtsQosMaxSduSize, c3gGsmMinUmtsQosSer, c3gGsmMinUmtsQosBer, c3gGsmMinUmtsQosDelay, c3gGsmMinUmtsQosPriority, c3gGsmMinUmtsQosSrcStatDescriptor, c3gGsmMinUmtsQosSignalIndication, c3gGsmMinUmtsQosRowStatus, c3gGsmReqGprsQosPrecedence, c3gGsmReqGprsQosDelay, c3gGsmReqGprsQosReliability, c3gGsmReqGprsQosPeakRate, c3gGsmReqGprsQosMeanRate, c3gGsmReqGprsQosRowStatus, c3gGsmMinGprsQosPrecedence, c3gGsmMinGprsQosDelay, c3gGsmMinGprsQosReliability, c3gGsmMinGprsQosPeakRate, c3gGsmMinGprsQosMeanRate, c3gGsmMinGprsQosRowStatus, c3gCurrentGsmRssi, c3gCurrentGsmEcIo, c3gGsmCurrentBand, c3gGsmChannelNumber, c3gGsmNumberOfNearbyCell, c3gGsmNearbyCellPrimaryScramblingCode, c3gGsmNearbyCellRscp, c3gGsmNearbyCellEcIoMeasurement, c3gGsmHistoryRssiPerSecond, c3gGsmHistoryRssiPerMinute, c3gGsmHistoryRssiPerHour, c3gGsmChv1, c3gGsmSimStatus, c3gGsmSimUserOperationRequired, c3gGsmNumberOfRetriesRemaining } STATUS current DESCRIPTION "A collection of objects for Cellular 3G GSM and LTE." ::= { ciscoWan3gMIBGroups 3 } ciscoWan3gMIBNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { c3gModemUpNotif, c3gModemDownNotif, c3gServiceChangedNotif, c3gNetworkChangedNotif, c3gConnectionStatusChangedNotif, c3gRssiOnsetNotif, c3gEcIoOnsetNotif, c3gRssiAbateNotif, c3gEcIoAbateNotif, c3gModemTemperOnsetNotif, c3gModemTemperAbateNotif } STATUS deprecated DESCRIPTION "A collection of objects for Cellular WAN notifications. ciscoWan3gMIBNotificationGroup object is superseded by ciscoWan3gMIBNotificationGroupRev1." ::= { ciscoWan3gMIBGroups 4 } ciscoWan3gMIBLbsObjectGroup OBJECT-GROUP OBJECTS { c3gLbsModeSelected, c3gLbsState, c3gLbsLocFixError, c3gLbsLatitude, c3gLbsLongitude, c3gLbsTimeStamp, c3gLbsLocUncertaintyAngle, c3gLbsLocUncertaintyA, c3gLbsLocUncertaintyPos, c3gLbsFixtype, c3gLbsHeightValid, c3gLbsHeight, c3gLbsLocUncertaintyVertical, c3gLbsVelocityValid, c3gLbsHeading, c3gLbsVelocityHorizontal, c3gLbsVelocityVertical, c3gLbsHepe, c3gLbsNumSatellites, c3gWanLbsSatelliteNumber, c3gWanLbsSatelliteElevation, c3gWanLbsSatelliteAzimuth, c3gWanLbsSatelliteUsed, c3gWanLbsSatelliteInfoSignalNoiseRatio, c3gWanLbsSatelliteInfoRowStatus } STATUS current DESCRIPTION "A collection of common objects for Cellular Location Based Service." ::= { ciscoWan3gMIBGroups 5 } ciscoWan3gMIBSmsObjectGroup OBJECT-GROUP OBJECTS { c3gSmsServiceAvailable, c3gSmsOutSmsCount, c3gSmsOutSmsErrorCount, c3gSmsInSmsStorageUsed, c3gSmsInSmsStorageUnused, c3gSmsInSmsArchiveCount, c3gSmsInSmsArchiveErrorCount, c3gSmsInSmsArchived, c3gSmsArchiveUrl, c3gSmsOutSmsStatus, c3gSmsInSmsCount, c3gSmsInSmsDeleted, c3gSmsInSmsStorageMax, c3gSmsInSmsCallBack, c3gSmsOutSmsPendingCount, c3gSmsOutSmsArchiveCount, c3gSmsOutSmsArchiveErrorCount } STATUS current DESCRIPTION "A collection of common objects for Cellular Short Messaging Service." ::= { ciscoWan3gMIBGroups 6 } ciscoWan3gMIBNotificationGroupRev1 NOTIFICATION-GROUP NOTIFICATIONS { c3gModemUpNotif, c3gModemDownNotif, c3gServiceChangedNotif, c3gNetworkChangedNotif, c3gConnectionStatusChangedNotif, c3gRssiOnsetNotif, c3gEcIoOnsetNotif, c3gRssiAbateNotif, c3gEcIoAbateNotif, c3gModemTemperOnsetNotif, c3gModemTemperAbateNotif, c3gModemTemperOnsetRecoveryNotif, c3gModemTemperAbateRecoveryNotif } STATUS current DESCRIPTION "A collection of objects for Cellular WAN notifications." ::= { ciscoWan3gMIBGroups 7 } END