-- CISCO-TELEPRESENCE-MIB.my: Cisco MIB to manage a -- Telepresence System -- -- Copyright (c) 2007-2012 by Cisco Systems Inc. -- All rights reserved. -- -- ****************************************************************** CISCO-TELEPRESENCE-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, NOTIFICATION-TYPE FROM SNMPv2-SMI MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP FROM SNMPv2-CONF TEXTUAL-CONVENTION, TruthValue, TimeStamp FROM SNMPv2-TC SnmpAdminString FROM SNMP-FRAMEWORK-MIB InetAddress, InetAddressType FROM INET-ADDRESS-MIB InterfaceIndexOrZero FROM IF-MIB ciscoMgmt FROM CISCO-SMI; ciscoTelepresenceMIB MODULE-IDENTITY LAST-UPDATED "201207130000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cochan@cisco.com" DESCRIPTION "The MIB module defines the managed objects for a Telepresence system. Telepresence refers to a set of technologies which allow a person to feel as if they were present, to give the appearance that they were present, or to have an effect, at a location other than their true location. A complete Telepresence system includes one or more Telepresence CODECS and peripherals such as display, camera, speaker, microphone and presentation device. Peripherals are attached directly to a Telepresence CODEC via an interface. Some peripherals may have more than one interface to transmit audio and/or video data and provide a configuration and/or control access." REVISION "201207170000Z" DESCRIPTION "Added detectionDisabled in CtpPeripheralStatusCode" REVISION "201203230000Z" DESCRIPTION "Added ctpVlanId, ctpDefaultGateway and ctpDefaultGatewayAddrType in ctpObjects" REVISION "201108230000Z" DESCRIPTION "Added uiDevice in CtpPeripheralDeviceCategoryCode" REVISION "201007230000Z" DESCRIPTION "Added ctpUSBPeripheralStatusTable and ctpWIFIPeripheralStatusTable in ctpPeripheralStatusEntry. ciscoTelepresenceComplianceR02 has been deprecated by ciscoTelepresenceComplianceR03. ciscoTpPeripheralStatusGroupR01 has been deprecated by ciscoTpPeripheralStatusGroupR02" REVISION "201007130000Z" DESCRIPTION "Added ctpPeriStatusChangeNotifyEnable." REVISION "200907120000Z" DESCRIPTION "Added ctpPeripheralDeviceCategory and ctpPeripheralDeviceNumber in ctpPeripheralStatusEntry. Added commError in CtpPeripheralStatusCode. Updated the description of ctpPeripheralErrorHistoryTable." REVISION "200802130000Z" DESCRIPTION "Added serial peripheral status and peripheral attribute table." REVISION "200712110000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 643 } -- Textual Conventions CtpSystemResetMode ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This textual convention identifies the system reset mode. noRestart (1) -- No operation. restartPending (2) -- Restart a system without shutting down when there is no active call; otherwise, system will be restarted after the call is terminated. resetPending (3) -- Shut down a system and bring it back up if there is no active call; otherwise, system will be reset after the call is terminated. forceReset (4) -- Shut down a system and bring it back up no matter if there is an active call or not." SYNTAX INTEGER { noRestart(1), -- the following three values are -- states: these values may be -- read or written restartPending(2), resetPending(3), forceReset(4) -- the following value is action: -- it may be written but not read } CtpPeripheralCableCode ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The textual convention identifies cable status of the attached peripheral through HDMI. plugged (1) -- Peripheral cable is plugged. loose (2) -- Peripheral cable is loose. unplugged (3) -- Peripheral cable is unplugged. unknown (4) -- Cannot detect peripheral cable status. internalError (5) -- Internal error." SYNTAX INTEGER { plugged(1), loose(2), unplugged(3), unknown(4), internalError(5) } CtpPeripheralPowerCode ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The textual convention identifies power status of the attached peripheral through HDMI. on (1) -- Peripheral power is on. standby (2) -- Peripheral power is in standby mode. off (3) -- Peripheral power is off. unknown (4) -- Cannot detect peripheral power status. internalError (5) -- Internal error." SYNTAX INTEGER { on(1), standby(2), off(3), unknown(4), internalError(5) } CtpPeripheralStatusCode ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The textual convention identifies the peripheral status. noError (0) -- Expected peripheral device is functioning through the attached port. other (1) -- None of the listed state. cableError (2) -- Expected peripheral device has cabling issue. powerError (3) -- Expected peripheral device has power issue. mgmtSysConfigError (4) -- Expected peripheral device has communications management system configuration issue. systemError (5) -- Telepresence system error. deviceError (6) -- Expected peripheral device is attached but not fully functional. linkError (7) -- Expected peripheral device has port level link issue. commError (8) -- Expected peripheral device has port level communication issue. detectionDisabled (9) -- Status detection has been disabled." SYNTAX INTEGER { noError(0), other(1), cableError(2), powerError(3), mgmtSysConfigError(4), systemError(5), deviceError(6), linkError(7), commError(8), detectionDisabled(9) } CtpSystemAccessProtocol ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The textual convention identifies supported Telepresence user access protocol. http (1) -- Hypertext Transfer Protocol (HTTP) snmp (2) -- Simple Network Management Protocol (SNMP) ssh (3) -- Secure Shell (SSH)" SYNTAX INTEGER { http(1), snmp(2), ssh(3) } CtpPeripheralDeviceCategoryCode ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The textual convention identifies the peripheral type. unknown (0) -- Unknown Device other (1) -- None of the listed device uplinkDevice (2) -- Device attached to CTS uplink port ipPhone (3) -- IP phone camera (4) -- Camera display (5) -- Display secCodec (6) -- CTS secondary codec docCamera (7) -- Document camera projector (8) -- Projector dviDevice (9) -- Device attached to DVI port presentationCodec (10) -- CTS codec process presentation -- stream auxiliaryControlUnit (11) -- Auxiliary control unit audioExpansionUnit (12) -- Audio expansion unit microphone (13) -- Microphone headset (14) -- Headset positionMic (15) -- Position microphone digitalMediaSystem (16) -- Digitial Media System auxHDMIOuputDevice (17) -- Auxiliary HDMI output device uiDevice (18) -- User Interface device for CTS" SYNTAX INTEGER { unknown(0), other(1), uplinkDevice(2), ipPhone(3), camera(4), display(5), secCodec(6), docCamera(7), projector(8), dviDevice(9), presentationCodec(10), auxiliaryControlUnit(11), audioExpansionUnit(12), microphone(13), headset(14), positionMic(15), digitialMediaSystem(16), auxHDMIOutputDevice(17), uiDevice(18) } ciscoTelepresenceMIBNotifs OBJECT IDENTIFIER ::= { ciscoTelepresenceMIB 0 } ciscoTelepresenceMIBObjects OBJECT IDENTIFIER ::= { ciscoTelepresenceMIB 1 } ciscoTelepresenceMIBConform OBJECT IDENTIFIER ::= { ciscoTelepresenceMIB 2 } ctpObjects OBJECT IDENTIFIER ::= { ciscoTelepresenceMIBObjects 1 } ctpPeripheralStatusObjects OBJECT IDENTIFIER ::= { ciscoTelepresenceMIBObjects 2 } ctpEventHistory OBJECT IDENTIFIER ::= { ciscoTelepresenceMIBObjects 3 } -- Telepresence Management Configuration Group ctpPeripheralErrorNotifyEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object controls generation of ctpPeripheralErrorNotification. When the object is 'true(1)', generation of ctpPeripheralErrorNotification is enabled. When the object is 'false(2)', generation of ctpPeripheralErrorNotification is disabled. ctpPeripheralErrorNotifyEnable object is superseded by ctpPeriStatusChangeNotifyEnable." DEFVAL { false } ::= { ctpObjects 1 } ctpSysUserAuthFailNotifyEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object controls generation of ctpSysUserAuthFailNotification. When the object is 'true(1)', generation of ctpSysUserAuthFailNotification is enabled. When the object is 'false(2)', generation of ctpSysUserAuthFailNotification is disabled." DEFVAL { false } ::= { ctpObjects 2 } ctpSystemReset OBJECT-TYPE SYNTAX CtpSystemResetMode MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to reset or restart a Telepresence system." DEFVAL { noRestart } ::= { ctpObjects 3 } ctpPeriStatusChangeNotifyEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object controls generation of ctpPeriStatusChangeNotification. When the object is 'true(1)', generation of ctpPeriStatusChangeNotification is enabled. When the object is 'false(2)', generation of ctpPeriStatusChangeNotification is disabled." DEFVAL { false } ::= { ctpObjects 4 } ctpVlanId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Telepresence system VLAN ID." ::= { ctpObjects 5 } ctpDefaultGatewayAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the type of address contained in the corresponding instance of ctpDefaultGateway." ::= { ctpObjects 6 } ctpDefaultGateway OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Telepresence system default gateway." ::= { ctpObjects 7 } -- Telepresence Peripheral Status Group -- -- -- Peripheral Status Table ctpPeripheralStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF CtpPeripheralStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table contains system peripheral information. An entry in this table has a corresponding entry, INDEX-ed by the same value of ctpPeripheralIndex, in the table relevant to the type of interface: ctpEtherPeripheralStatusTable for Ethernet, ctpHDMIPeripheralStatusTable for HDMI or ctpDVIPeripheralStatusTable for DVI." ::= { ctpPeripheralStatusObjects 1 } ctpPeripheralStatusEntry OBJECT-TYPE SYNTAX CtpPeripheralStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry contains information about one peripheral which is configured or detected by a Telepresence system." INDEX { ctpPeripheralIndex } ::= { ctpPeripheralStatusTable 1 } CtpPeripheralStatusEntry ::= SEQUENCE { ctpPeripheralIndex Unsigned32, ctpPeripheralDescription SnmpAdminString, ctpPeripheralStatus CtpPeripheralStatusCode, ctpPeripheralDeviceCategory CtpPeripheralDeviceCategoryCode, ctpPeripheralDeviceNumber Unsigned32 } ctpPeripheralIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies a unique index for a peripheral which is attached to a Telepresence system." ::= { ctpPeripheralStatusEntry 1 } ctpPeripheralDescription OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies a description of the attached peripheral. Peripheral description may be the peripheral type, model and/or version information or a peripheral signal description." ::= { ctpPeripheralStatusEntry 2 } ctpPeripheralStatus OBJECT-TYPE SYNTAX CtpPeripheralStatusCode MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies a peripheral status." ::= { ctpPeripheralStatusEntry 3 } ctpPeripheralDeviceCategory OBJECT-TYPE SYNTAX CtpPeripheralDeviceCategoryCode MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies a peripheral category of a device." ::= { ctpPeripheralStatusEntry 4 } ctpPeripheralDeviceNumber OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies a device number for a peripheral. Device number is unique within the same peripheral device category." ::= { ctpPeripheralStatusEntry 5 } -- Peripheral Status Table connected via Ethernet ctpEtherPeripheralStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF CtpEtherPeripheralStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table contains information about all peripherals connected to the system via Ethernet port." ::= { ctpPeripheralStatusObjects 2 } ctpEtherPeripheralStatusEntry OBJECT-TYPE SYNTAX CtpEtherPeripheralStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry contains information about one peripheral attached to the Telepresence system via Ethernet." INDEX { ctpPeripheralIndex, ctpEtherPeripheralIndex } ::= { ctpEtherPeripheralStatusTable 1 } CtpEtherPeripheralStatusEntry ::= SEQUENCE { ctpEtherPeripheralIndex Unsigned32, ctpEtherPeripheralIfIndex InterfaceIndexOrZero, ctpEtherPeripheralAddrType InetAddressType, ctpEtherPeripheralAddr InetAddress, ctpEtherPeripheralStatus CtpPeripheralStatusCode } ctpEtherPeripheralIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies a unique number for a peripheral Ethernet interface. If no peripheral has more than one Ethernet interface, this object will have value '1'." ::= { ctpEtherPeripheralStatusEntry 1 } ctpEtherPeripheralIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "The object specifies an index value that uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of the IF-MIB's ifIndex. If this entry doesn't have corresponding ifIndex, then this value will have value '0'." ::= { ctpEtherPeripheralStatusEntry 2 } ctpEtherPeripheralAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the type of address contained in the corresponding instance of ctpEtherPeripheralAddr." ::= { ctpEtherPeripheralStatusEntry 3 } ctpEtherPeripheralAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the address of the attached peripheral in the format given by the corresponding instance of ctpEtherPeripheralAddrType." ::= { ctpEtherPeripheralStatusEntry 4 } ctpEtherPeripheralStatus OBJECT-TYPE SYNTAX CtpPeripheralStatusCode MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies attached peripheral status retrieved via Ethernet port." ::= { ctpEtherPeripheralStatusEntry 5 } -- Peripheral Status Table connected via HDMI ctpHDMIPeripheralStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF CtpHDMIPeripheralStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table contains information about all peripherals connected to the system via HDMI." ::= { ctpPeripheralStatusObjects 3 } ctpHDMIPeripheralStatusEntry OBJECT-TYPE SYNTAX CtpHDMIPeripheralStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry contains information about one Telepresence HDMI peripheral." INDEX { ctpPeripheralIndex, ctpHDMIPeripheralIndex } ::= { ctpHDMIPeripheralStatusTable 1 } CtpHDMIPeripheralStatusEntry ::= SEQUENCE { ctpHDMIPeripheralIndex Unsigned32, ctpHDMIPeripheralCableStatus CtpPeripheralCableCode, ctpHDMIPeripheralPowerStatus CtpPeripheralPowerCode } ctpHDMIPeripheralIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies a unique number for a peripheral HDMI. If no peripheral has more than one HDMI, this object will have value '1'." ::= { ctpHDMIPeripheralStatusEntry 1 } ctpHDMIPeripheralCableStatus OBJECT-TYPE SYNTAX CtpPeripheralCableCode MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies cable status of an attached peripheral. This object is set to 'loose' if system detects cable is 'unplugged' but power is 'on'." ::= { ctpHDMIPeripheralStatusEntry 2 } ctpHDMIPeripheralPowerStatus OBJECT-TYPE SYNTAX CtpPeripheralPowerCode MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies power status of an attached peripheral. This object is set to 'unknown' if system detects cable is 'unplugged'." ::= { ctpHDMIPeripheralStatusEntry 3 } -- Peripheral Status Table connected via DVI ctpDVIPeripheralStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF CtpDVIPeripheralStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table contains information about all peripherals connected to the system via DVI." ::= { ctpPeripheralStatusObjects 4 } ctpDVIPeripheralStatusEntry OBJECT-TYPE SYNTAX CtpDVIPeripheralStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry contains information about one peripheral attached to the Telepresence system via DVI." INDEX { ctpPeripheralIndex, ctpDVIPeripheralIndex } ::= { ctpDVIPeripheralStatusTable 1 } CtpDVIPeripheralStatusEntry ::= SEQUENCE { ctpDVIPeripheralIndex Unsigned32, ctpDVIPeripheralCableStatus CtpPeripheralCableCode } ctpDVIPeripheralIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies a unique number for a peripheral DVI. If no peripheral has more than one DVI, this object will have value '1'. Note that some Telepresence systems have no DVI port and some Telepresence systems have only one DVI port." ::= { ctpDVIPeripheralStatusEntry 1 } ctpDVIPeripheralCableStatus OBJECT-TYPE SYNTAX CtpPeripheralCableCode MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies attached device cable status reported by DVI." ::= { ctpDVIPeripheralStatusEntry 2 } -- Peripheral Status Table connected via RS-232 ctpRS232PeripheralStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF CtpRS232PeripheralStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table contains information about all peripherals connected to the system via RS-232." ::= { ctpPeripheralStatusObjects 5 } ctpRS232PeripheralStatusEntry OBJECT-TYPE SYNTAX CtpRS232PeripheralStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry contains information about one peripheral attached to the Telepresence system via RS-232." INDEX { ctpPeripheralIndex, ctpRS232PeripheralIndex } ::= { ctpRS232PeripheralStatusTable 1 } CtpRS232PeripheralStatusEntry ::= SEQUENCE { ctpRS232PeripheralIndex Unsigned32, ctpRS232PortIndex InterfaceIndexOrZero, ctpRS232PeripheralConnStatus INTEGER } ctpRS232PeripheralIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies a unique number for a peripheral RS-232. If no peripheral has more than one RS-232, this object will have value '1'. Note that some Telepresence systems have no RS-232 port." ::= { ctpRS232PeripheralStatusEntry 1 } ctpRS232PortIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "The object specifies an index value that uniquely identifies the RS-232 port to which this entry is applicable. Its value is the same as RS-232-MIB's rs232PortIndex for the port. If RS-232-MIB is not supported by the agent, then this value will have value '0'." ::= { ctpRS232PeripheralStatusEntry 2 } ctpRS232PeripheralConnStatus OBJECT-TYPE SYNTAX INTEGER { connected(1), unknown(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies peripheral which is connected via RS232. When the object is 'connected(1)', peripheral connection via RS232 is working properly. When the object is 'unknown(2)', peripheral connection via RS232 is not working properly. It may due to device problem or connection problem." ::= { ctpRS232PeripheralStatusEntry 3 } -- Peripheral Attribute table ctpPeripheralAttributeTable OBJECT-TYPE SYNTAX SEQUENCE OF CtpPeripheralAttributeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table contains information about attributes for the peripherals which are connected to the system. Peripheral attribute may specify peripheral's component information, for example, an entry may specify lifetime of a lamp on a presentation device." ::= { ctpPeripheralStatusObjects 6 } ctpPeripheralAttributeEntry OBJECT-TYPE SYNTAX CtpPeripheralAttributeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry contains information about one peripheral attribute related to the peripheral specified by ctpPeripheralIndex." INDEX { ctpPeripheralIndex, ctpPeripheralAttributeIndex } ::= { ctpPeripheralAttributeTable 1 } CtpPeripheralAttributeEntry ::= SEQUENCE { ctpPeripheralAttributeIndex Unsigned32, ctpPeripheralAttributeDescr INTEGER, ctpPeripheralAttributeValue Unsigned32 } ctpPeripheralAttributeIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies a unique number for a peripheral attribute. If no peripheral has more than one attribute, this object will have value '1'." ::= { ctpPeripheralAttributeEntry 1 } ctpPeripheralAttributeDescr OBJECT-TYPE SYNTAX INTEGER { lampOperTime(1), lampState(2), powerSwitchState(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies description of a attribute. The supported attributes are lampOperTime(1) -- indicate the lamp operating time of a peripheral lampState(2) -- indicate the lamp state powerSwitchState(3) -- indicate the power on/off state of a peripheral Note that not all peripheral contains all the supported attributes. Agent reports whatever is available." ::= { ctpPeripheralAttributeEntry 2 } ctpPeripheralAttributeValue OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies value of the attribute corresponding to ctpPeripheralAttributeDescr. The possible value of the supported attributes is listed as the following: Attribute Unit SYNTAX ----------------------------------------------------------- lampOperTime hours Unsigned32(0..4294967295) lampState INTEGER { on(1), off(2), failure(3), unknown(4) } powerSwitchState INTEGER { on(1), off(2), unknown(3) }" ::= { ctpPeripheralAttributeEntry 3 } ctpUSBPeripheralStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF CtpUSBPeripheralStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information about all the peripherals connected to the system via USB." ::= { ctpPeripheralStatusObjects 7 } ctpUSBPeripheralStatusEntry OBJECT-TYPE SYNTAX CtpUSBPeripheralStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry drescribes a peripheral connected to the Telepresence system through USB." INDEX { ctpPeripheralIndex, ctpUSBPeripheralIndex } ::= { ctpUSBPeripheralStatusTable 1 } CtpUSBPeripheralStatusEntry ::= SEQUENCE { ctpUSBPeripheralIndex Unsigned32, ctpUSBPeripheralCableStatus CtpPeripheralCableCode, ctpUSBPeripheralPowerStatus INTEGER, ctpUSBPeripheralPortType INTEGER, ctpUSBPeripheralPortRate INTEGER } ctpUSBPeripheralIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates an arbitrary positive, integer-value that uniquely identifies the USB peripheral." ::= { ctpUSBPeripheralStatusEntry 1 } ctpUSBPeripheralCableStatus OBJECT-TYPE SYNTAX CtpPeripheralCableCode MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the status of the cable attaching the USB peripheral." ::= { ctpUSBPeripheralStatusEntry 2 } ctpUSBPeripheralPowerStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), self(2), bus(3), both(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the source of power for the attached USB peripheral: 'unknown' - The source of power is unknown. 'self' - The USB peripheral is externally powered. 'bus' - The USB peripheral is powered by the USB bus. 'both' - The USB peripheral can be powered by both the USB bus or self" ::= { ctpUSBPeripheralStatusEntry 3 } ctpUSBPeripheralPortType OBJECT-TYPE SYNTAX INTEGER { host(1), device(2), hub(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the type of device connected to the USB port: 'host' - no device os connected to the port 'device' - a usb device is connected to the port 'hub' - a usb hub is connected to the port" ::= { ctpUSBPeripheralStatusEntry 4 } ctpUSBPeripheralPortRate OBJECT-TYPE SYNTAX INTEGER { low(1), full(2), high(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the current operational rate of the USB peripheral: 'unknown' - The USB port rate is unknown 'low' - The USB port rate is at 1.5 Mbps. 'full' - The USB port rate is at 12 Mbps. 'high' - The USB port rate is at 480 Mbps." ::= { ctpUSBPeripheralStatusEntry 5 } -- Peripheral Status Table connected via 802dot11 ctp802dot11PeripheralStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF Ctp802dot11PeripheralStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table contains information about all peripherals connected to the system via 802dot11." ::= { ctpPeripheralStatusObjects 8 } ctp802dot11PeripheralStatusEntry OBJECT-TYPE SYNTAX Ctp802dot11PeripheralStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry describes one Telepresence 802dot11 peripheral." INDEX { ctpPeripheralIndex, ctp802dot11PeripheralIndex } ::= { ctp802dot11PeripheralStatusTable 1 } Ctp802dot11PeripheralStatusEntry ::= SEQUENCE { ctp802dot11PeripheralIndex Unsigned32, ctp802dot11PeripheralIfIndex InterfaceIndexOrZero, ctp802dot11PeripheralAddrType InetAddressType, ctp802dot11PeripheralAddr InetAddress, ctp802dot11PeripheralLinkStrength Unsigned32, ctp802dot11PeripheralLinkStatus CtpPeripheralCableCode } ctp802dot11PeripheralIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates an arbitrary positive, integer-value that uniquely identifies the IEEE 802.11 peripheral." ::= { ctp802dot11PeripheralStatusEntry 1 } ctp802dot11PeripheralIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates an index value that uniquely identifies the interface to which this entry is applicable. If this entry doesn't have corresponding ifIndex, then this value will have value '0'." ::= { ctp802dot11PeripheralStatusEntry 2 } ctp802dot11PeripheralAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the type of address indicated by the corresponding instance of ctp802dot11PeripheralAddr." ::= { ctp802dot11PeripheralStatusEntry 3 } ctp802dot11PeripheralAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the address of the attached peripheral in the format indicated by the corresponding instance of ctp802dot11PeripheralAddrType." ::= { ctp802dot11PeripheralStatusEntry 4 } ctp802dot11PeripheralLinkStrength OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the link strength of an IEEE 802.11 link for a peripheral. A return value of 0 indicates the link is not connected. A return value between 1 - 5 indicates the strength of the link, with 1 being the weakest and 5 being the strongest." ::= { ctp802dot11PeripheralStatusEntry 5 } -- changed to link status. This field is to represent the link status of -- the 802dot11 link. ctp802dot11PeripheralLinkStatus OBJECT-TYPE SYNTAX CtpPeripheralCableCode MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the link status of the attached peripheral via IEEE 802.11 link." ::= { ctp802dot11PeripheralStatusEntry 6 } -- Event History Group -- -- Telepresence Peripheral Error History Table ctpPeripheralErrorHistTableSize OBJECT-TYPE SYNTAX Unsigned32 (0..500) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the maximum number of entries that the ctpPeripheralErrorHistTable can contain. When the capacity of the ctpPeripheralErrorHistTable has reached the value specified by this object, then the agent deletes the oldest entity in order to accommodate the new entry. A value of '0' prevents any history from being retained. Some agents restrict the value of this object to be less than 500." DEFVAL { 10 } ::= { ctpEventHistory 1 } ctpPeripheralErrorHistLastIndex OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the value of the ctpPeripheralErrorHistIndex object corresponding to the last entry added to the table by the agent. If the management application uses the notifications defined by this module, then it can poll this object to determine whether it has missed a notification sent by the agent." ::= { ctpEventHistory 2 } ctpPeripheralErrorHistoryTable OBJECT-TYPE SYNTAX SEQUENCE OF CtpPeripheralErrorHistoryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains a history of the detected peripheral status changes. After a management agent restart, when sysUpTime is reset to zero, this table records all notifications until such time as it becomes full. Thereafter, it remains full by retaining the number of most recent notifications specified in ctpPeripheralErrorHistTableSize." ::= { ctpEventHistory 3 } ctpPeripheralErrorHistoryEntry OBJECT-TYPE SYNTAX CtpPeripheralErrorHistoryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry contains information about a Telepresence peripheral status changes." INDEX { ctpPeripheralErrorHistoryIndex } ::= { ctpPeripheralErrorHistoryTable 1 } CtpPeripheralErrorHistoryEntry ::= SEQUENCE { ctpPeripheralErrorHistoryIndex Unsigned32, ctpPeripheralErrorIndex Unsigned32, ctpPeripheralErrorStatus CtpPeripheralStatusCode, ctpPeripheralErrorTimeStamp TimeStamp, ctpPeripheralErrorDeviceCategory CtpPeripheralDeviceCategoryCode, ctpPeripheralErrorDeviceNumber Unsigned32 } ctpPeripheralErrorHistoryIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique non-zero integer value that identifies a CtpPeripheralErrorHistoryEntry in the table. The value of this index starts from '1' and monotonically increases for each peripheral error known to the agent. If the value of this object is '4294967295', the agent will use '1' as the value of the next detected peripheral status change." ::= { ctpPeripheralErrorHistoryEntry 1 } ctpPeripheralErrorIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The object specifies the value of ctpPeripheralIndex of a peripheral which is in error state. This object is deprecated in favor of ctpPeripheralErrorDeviceCategory and ctpPeripheralErrorDeviceNumber." ::= { ctpPeripheralErrorHistoryEntry 2 } ctpPeripheralErrorStatus OBJECT-TYPE SYNTAX CtpPeripheralStatusCode MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the peripheral status after its status changed." ::= { ctpPeripheralErrorHistoryEntry 3 } ctpPeripheralErrorTimeStamp OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the value of the sysUpTime object at the time the notification was generated." ::= { ctpPeripheralErrorHistoryEntry 4 } ctpPeripheralErrorDeviceCategory OBJECT-TYPE SYNTAX CtpPeripheralDeviceCategoryCode MAX-ACCESS read-only STATUS current DESCRIPTION "The object specifies peripheral device category after its status changed." ::= { ctpPeripheralErrorHistoryEntry 5 } ctpPeripheralErrorDeviceNumber OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The object specifies peripheral device number after its status changed. Device number is unique within the same peripheral device category." ::= { ctpPeripheralErrorHistoryEntry 6 } -- User Authentication Failure History Table ctpSysUserAuthFailHistTableSize OBJECT-TYPE SYNTAX Unsigned32 (0..500) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the number of entries that the ctpSysUserAuthFailHistTable can contain. When the capacity of the ctpSysUserAuthFailHistTable has reached the value specified by this object, then the agent deletes the oldest entity in order to accommodate the new entry. A value of '0' prevents any history from being retained. Some agents restrict the value of this object to be less than 500." DEFVAL { 10 } ::= { ctpEventHistory 4 } ctpSysUserAuthFailHistLastIndex OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the value of the ctpSysUserAuthFailHistIndex object corresponding to the last entry added to the table by the agent. If the management application uses the notifications defined by this module, then it can poll this object to determine whether it has missed a notification sent by the agent." ::= { ctpEventHistory 5 } ctpSysUserAuthFailHistoryTable OBJECT-TYPE SYNTAX SEQUENCE OF CtpSysUserAuthFailHistoryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains a history of detected user authentication failures. After a management agent restart, when sysUpTime is reset to zero, this table records all user authentication failure notifications until such time as it becomes full. Thereafter, it remains full by retaining the number of most recent notifications specified in ctpSysUserAuthFailHistTableSize." ::= { ctpEventHistory 6 } ctpSysUserAuthFailHistoryEntry OBJECT-TYPE SYNTAX CtpSysUserAuthFailHistoryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry contains information about a Telepresence system user authentication failure." INDEX { ctpSysUserAuthFailHistoryIndex } ::= { ctpSysUserAuthFailHistoryTable 1 } CtpSysUserAuthFailHistoryEntry ::= SEQUENCE { ctpSysUserAuthFailHistoryIndex Unsigned32, ctpSysUserAuthFailSourceAddrType InetAddressType, ctpSysUserAuthFailSourceAddr InetAddress, ctpSysUserAuthFailSourcePort Unsigned32, ctpSysUserAuthFailUserName SnmpAdminString, ctpSysUserAuthFailAccessProtocol CtpSystemAccessProtocol, ctpSysUserAuthFailTimeStamp TimeStamp } ctpSysUserAuthFailHistoryIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique non-zero integer value that identifies a CtpSysUserAuthFailHistoryEntry in the table. The value of this index starts from '1' and monotonically increases for each system authentication failure event known to the agent. If the value of this object is '4294967295', the agent will use '1' as the value of the next user authentication failure event." ::= { ctpSysUserAuthFailHistoryEntry 1 } ctpSysUserAuthFailSourceAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The object specifies the type of address contained in the corresponding instance of ctpSysUserAuthFailSourceAddr." ::= { ctpSysUserAuthFailHistoryEntry 2 } ctpSysUserAuthFailSourceAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The object specifies the source address when the user authentication failure occurred, in the format given by the corresponding instance of ctpSysUserAuthFailSourceAddrType." ::= { ctpSysUserAuthFailHistoryEntry 3 } ctpSysUserAuthFailSourcePort OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The object specifies the source TCP/UDP port number when a user authentication failure occurred." ::= { ctpSysUserAuthFailHistoryEntry 4 } ctpSysUserAuthFailUserName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The object specifies the user name which was used to gain system access when authentication failure occurred." ::= { ctpSysUserAuthFailHistoryEntry 5 } ctpSysUserAuthFailAccessProtocol OBJECT-TYPE SYNTAX CtpSystemAccessProtocol MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the access protocol when a user authentication failure occurred." ::= { ctpSysUserAuthFailHistoryEntry 6 } ctpSysUserAuthFailTimeStamp OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the value of the sysUpTime object at the time the notification was generated." ::= { ctpSysUserAuthFailHistoryEntry 7 } -- Telepresence System Notifications ctpPeripheralErrorNotification NOTIFICATION-TYPE OBJECTS { ctpPeripheralErrorIndex, ctpPeripheralErrorStatus } STATUS deprecated DESCRIPTION "This notification is sent when a peripheral error is detected. This notification is deprecated in favor of ctpPeriStatusChangeNotification. ctpPeripheralErrorNotification object is superseded by ctpPeriStatusChangeNotification." ::= { ciscoTelepresenceMIBNotifs 1 } ctpSysUserAuthFailNotification NOTIFICATION-TYPE OBJECTS { ctpSysUserAuthFailSourceAddrType, ctpSysUserAuthFailSourceAddr, ctpSysUserAuthFailSourcePort, ctpSysUserAuthFailUserName, ctpSysUserAuthFailAccessProtocol } STATUS current DESCRIPTION "This notification is sent when a user authentication failure via a Telepresence supported access protocol is detected." ::= { ciscoTelepresenceMIBNotifs 2 } ctpPeriStatusChangeNotification NOTIFICATION-TYPE OBJECTS { ctpPeripheralErrorIndex, ctpPeripheralErrorDeviceCategory, ctpPeripheralErrorDeviceNumber, ctpPeripheralErrorStatus } STATUS current DESCRIPTION "This notification is sent when a peripheral status is changed." ::= { ciscoTelepresenceMIBNotifs 3 } -- Conformance ciscoTelepresenceCompliances OBJECT IDENTIFIER ::= { ciscoTelepresenceMIBConform 1 } ciscoTelepresenceMIBGroups OBJECT IDENTIFIER ::= { ciscoTelepresenceMIBConform 2 } ciscoTelepresenceCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for entities which implement the Cisco Telepresence MIB." MODULE -- this module MANDATORY-GROUPS { ciscoTpConfigurationGroup, ciscoTpPeripheralStatusGroup, ciscoTpEventHistoryGroup, ciscoTpNotificationGroup } OBJECT ctpPeripheralErrorNotifyEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ctpSysUserAuthFailNotifyEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ctpSystemReset MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ctpPeripheralErrorHistTableSize MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ctpSysUserAuthFailHistTableSize MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { ciscoTelepresenceCompliances 1 } ciscoTelepresenceComplianceR01 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for entities which implement the Cisco Telepresence MIB." MODULE -- this module MANDATORY-GROUPS { ciscoTpConfigurationGroup, ciscoTpPeripheralStatusGroup, ciscoTpEventHistoryGroup, ciscoTpNotificationGroup } GROUP ciscoTpRS232PeripheralStatusGroup DESCRIPTION "This group is mandatory for a Telepresence system which has RS323 interface." GROUP ciscoTpPeripheralAttributeGroup DESCRIPTION "This group is optional." OBJECT ctpPeripheralErrorNotifyEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ctpSysUserAuthFailNotifyEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ctpSystemReset MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ctpPeripheralErrorHistTableSize MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ctpSysUserAuthFailHistTableSize MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { ciscoTelepresenceCompliances 2 } ciscoTelepresenceComplianceR02 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for entities which implement the Cisco Telepresence MIB." MODULE -- this module MANDATORY-GROUPS { ciscoTpConfigurationGroupR01, ciscoTpPeripheralStatusGroupR01, ciscoTpEventHistoryGroupR01, ciscoTpNotificationGroupR01 } GROUP ciscoTpRS232PeripheralStatusGroup DESCRIPTION "This group is mandatory for a Telepresence system which has RS323 interface." GROUP ciscoTpPeripheralAttributeGroup DESCRIPTION "This group is optional." OBJECT ctpSysUserAuthFailNotifyEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ctpSystemReset MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ctpPeriStatusChangeNotifyEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ctpSysUserAuthFailHistTableSize MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ctpPeripheralErrorHistTableSize MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { ciscoTelepresenceCompliances 3 } ciscoTelepresenceComplianceR03 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for entities which implement the Cisco Telepresence MIB." MODULE -- this module MANDATORY-GROUPS { ciscoTpConfigurationGroupR01, ciscoTpPeripheralStatusGroupR02, ciscoTpEventHistoryGroupR01, ciscoTpNotificationGroupR01 } GROUP ciscoTpRS232PeripheralStatusGroup DESCRIPTION "This group is mandatory for a Telepresence system which has RS323 interface." GROUP ciscoTpPeripheralAttributeGroup DESCRIPTION "This group is optional." OBJECT ctpSysUserAuthFailNotifyEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ctpSystemReset MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ctpSysUserAuthFailHistTableSize MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ctpPeripheralErrorHistTableSize MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { ciscoTelepresenceCompliances 4 } ciscoTelepresenceComplianceR04 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement the Cisco Telepresence MIB." MODULE -- this module MANDATORY-GROUPS { ciscoTpConfigurationGroupR01, ciscoTpConfigurationGroupR02, ciscoTpPeripheralStatusGroupR02, ciscoTpEventHistoryGroupR01, ciscoTpNotificationGroupR01 } GROUP ciscoTpRS232PeripheralStatusGroup DESCRIPTION "This group is mandatory for a Telepresence system which has RS323 interface." GROUP ciscoTpPeripheralAttributeGroup DESCRIPTION "This group is optional." OBJECT ctpSysUserAuthFailNotifyEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ctpSystemReset MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ctpSysUserAuthFailHistTableSize MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ctpPeripheralErrorHistTableSize MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { ciscoTelepresenceCompliances 5 } -- Units of Conformance ciscoTpConfigurationGroup OBJECT-GROUP OBJECTS { ctpPeripheralErrorNotifyEnable, ctpSysUserAuthFailNotifyEnable, ctpSystemReset } STATUS deprecated DESCRIPTION "A collection of objects providing the notification configuration and system reset. ciscoTpConfigurationGroup object is superseded by ciscoTpConfigurationGroupR01." ::= { ciscoTelepresenceMIBGroups 1 } ciscoTpPeripheralStatusGroup OBJECT-GROUP OBJECTS { ctpPeripheralDescription, ctpPeripheralStatus, ctpEtherPeripheralIfIndex, ctpEtherPeripheralAddrType, ctpEtherPeripheralAddr, ctpEtherPeripheralStatus, ctpHDMIPeripheralCableStatus, ctpHDMIPeripheralPowerStatus, ctpDVIPeripheralCableStatus } STATUS deprecated DESCRIPTION "A collection of objects providing the Telepresence peripheral information. ciscoTpPeripheralStatusGroup object is superseded by ciscoTpPeripheralStatusGroupR01." ::= { ciscoTelepresenceMIBGroups 2 } ciscoTpEventHistoryGroup OBJECT-GROUP OBJECTS { ctpPeripheralErrorHistTableSize, ctpPeripheralErrorHistLastIndex, ctpPeripheralErrorIndex, ctpPeripheralErrorStatus, ctpPeripheralErrorTimeStamp, ctpSysUserAuthFailHistTableSize, ctpSysUserAuthFailHistLastIndex, ctpSysUserAuthFailSourceAddrType, ctpSysUserAuthFailSourceAddr, ctpSysUserAuthFailSourcePort, ctpSysUserAuthFailUserName, ctpSysUserAuthFailAccessProtocol, ctpSysUserAuthFailTimeStamp } STATUS deprecated DESCRIPTION "A collection of managed objects providing notification event history information. ciscoTpEventHistoryGroup object is superseded by ciscoTpEventHistoryGroupR01." ::= { ciscoTelepresenceMIBGroups 3 } ciscoTpNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { ctpPeripheralErrorNotification, ctpSysUserAuthFailNotification } STATUS deprecated DESCRIPTION "A collection of Telepresence system notifications. ciscoTpNotificationGroup object is superseded by ciscoTpNotificationGroupR01." ::= { ciscoTelepresenceMIBGroups 4 } ciscoTpRS232PeripheralStatusGroup OBJECT-GROUP OBJECTS { ctpRS232PortIndex, ctpRS232PeripheralConnStatus } STATUS current DESCRIPTION "A collection of objects providing the information about Telepresence peripheral which is connected via RS232." ::= { ciscoTelepresenceMIBGroups 5 } ciscoTpPeripheralAttributeGroup OBJECT-GROUP OBJECTS { ctpPeripheralAttributeDescr, ctpPeripheralAttributeValue } STATUS current DESCRIPTION "A collection of managed objects providing peripheral attribute information." ::= { ciscoTelepresenceMIBGroups 6 } ciscoTpPeripheralStatusGroupR01 OBJECT-GROUP OBJECTS { ctpPeripheralDescription, ctpPeripheralStatus, ctpPeripheralDeviceCategory, ctpPeripheralDeviceNumber, ctpEtherPeripheralIfIndex, ctpEtherPeripheralAddrType, ctpEtherPeripheralAddr, ctpEtherPeripheralStatus, ctpHDMIPeripheralCableStatus, ctpHDMIPeripheralPowerStatus, ctpDVIPeripheralCableStatus } STATUS deprecated DESCRIPTION "A collection of objects providing the Telepresence peripheral information. ciscoTpPeripheralStatusGroupR01 object is superseded by ciscoTpPeripheralStatusGroupR02." ::= { ciscoTelepresenceMIBGroups 7 } ciscoTpEventHistoryGroupR01 OBJECT-GROUP OBJECTS { ctpPeripheralErrorHistTableSize, ctpPeripheralErrorHistLastIndex, ctpPeripheralErrorIndex, ctpPeripheralErrorStatus, ctpPeripheralErrorTimeStamp, ctpPeripheralErrorDeviceCategory, ctpPeripheralErrorDeviceNumber, ctpSysUserAuthFailHistTableSize, ctpSysUserAuthFailHistLastIndex, ctpSysUserAuthFailSourceAddrType, ctpSysUserAuthFailSourceAddr, ctpSysUserAuthFailSourcePort, ctpSysUserAuthFailUserName, ctpSysUserAuthFailAccessProtocol, ctpSysUserAuthFailTimeStamp } STATUS current DESCRIPTION "A collection of managed objects providing notification event history information." ::= { ciscoTelepresenceMIBGroups 8 } ciscoTpNotificationGroupR01 NOTIFICATION-GROUP NOTIFICATIONS { ctpPeriStatusChangeNotification, ctpSysUserAuthFailNotification } STATUS current DESCRIPTION "A collection of Telepresence system notifications." ::= { ciscoTelepresenceMIBGroups 9 } ciscoTpConfigurationGroupR01 OBJECT-GROUP OBJECTS { ctpSysUserAuthFailNotifyEnable, ctpSystemReset, ctpPeriStatusChangeNotifyEnable } STATUS current DESCRIPTION "A collection of objects providing the notification configuration and system reset." ::= { ciscoTelepresenceMIBGroups 10 } ciscoTpPeripheralStatusGroupR02 OBJECT-GROUP OBJECTS { ctpPeripheralDescription, ctpPeripheralStatus, ctpPeripheralDeviceCategory, ctpPeripheralDeviceNumber, ctpEtherPeripheralIfIndex, ctpEtherPeripheralAddrType, ctpEtherPeripheralAddr, ctpEtherPeripheralStatus, ctpHDMIPeripheralCableStatus, ctpHDMIPeripheralPowerStatus, ctpDVIPeripheralCableStatus, ctpUSBPeripheralCableStatus, ctpUSBPeripheralPowerStatus, ctpUSBPeripheralPortType, ctpUSBPeripheralPortRate, ctp802dot11PeripheralIfIndex, ctp802dot11PeripheralAddrType, ctp802dot11PeripheralAddr, ctp802dot11PeripheralLinkStrength, ctp802dot11PeripheralLinkStatus } STATUS current DESCRIPTION "A collection of objects providing the Telepresence peripheral information." ::= { ciscoTelepresenceMIBGroups 11 } ciscoTpConfigurationGroupR02 OBJECT-GROUP OBJECTS { ctpVlanId, ctpDefaultGateway, ctpDefaultGatewayAddrType } STATUS current DESCRIPTION "A collection of objects providing network configurations." ::= { ciscoTelepresenceMIBGroups 12 } END