-- ***************************************************************** -- Cisco Switch Engine MIB -- -- February 2000, Steven To -- July 2000, Edward Pham -- February 2002, Edward Pham -- February 2003, Edward Pham -- May 2003, Jayakumar Kadirvelu -- August 2003, Edward Pham -- -- Copyright (c) 2000-2013 by cisco Systems Inc. -- by cisco Systems, Inc. -- All rights reserved. -- ***************************************************************** CISCO-SWITCH-ENGINE-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Gauge32, Counter32, Counter64, IpAddress, Integer32, Unsigned32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF ifIndex, OwnerString, InterfaceIndexOrZero FROM IF-MIB InetAddressType, InetAddress FROM INET-ADDRESS-MIB entPhysicalIndex FROM ENTITY-MIB TEXTUAL-CONVENTION, DisplayString, RowStatus, TimeInterval, MacAddress, TruthValue, TimeStamp FROM SNMPv2-TC SnmpAdminString FROM SNMP-FRAMEWORK-MIB MplsVpnId FROM MPLS-VPN-MIB CiscoNetworkProtocol, CiscoPort FROM CISCO-TC VlanIndex FROM CISCO-VTP-MIB ciscoMgmt FROM CISCO-SMI; ciscoSwitchEngineMIB MODULE-IDENTITY LAST-UPDATED "201302130000Z" ORGANIZATION "Cisco Systems Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-lan-switch-snmp@cisco.com" DESCRIPTION "This MIB module defines management objects for Cisco Layer 2/3 switches. These devices may either have a single (central) switching engine entity or may consist of multiple (distributed) switching engine entities which are inter-connected via a common 'switching fabric'. In the central switching engine model, all the physical ports in the system are handled by the only switching engine in the system. In the distributed switching model, each switching engine will handle a set of 'local' physical ports and when necessary, packets are also switched between switching engines over the switching fabric. Cisco L2/L3 switching devices use regular routers to assist them in learning packet 'flows' by observing how a router routes a candidate flow. A flow is some combination of source network address, destination network address and the transport port numbers, as applicable. Once a flow is established (learned), all traffic belonging to that flow will be switched at Layer 3 by the switch engine, effectively bypassing the router, until the flow has been 'aged' out. Most Cisco L2/L3 switching devices employ built-in (internal) router module(s) for integrating Layer 3 switching with Layer 2 forwarding. However, they can also learn 'flows' through other physically-separate (external) Cisco routers that are connected to the switch-engine through the network." REVISION "201302130000Z" DESCRIPTION "Add enumerated value 37 - 85 to cseTcamResourceType." REVISION "201203120000Z" DESCRIPTION "Add cseStatisticsFlowGroup1." REVISION "201012170000Z" DESCRIPTION "Add the following new enumerations to cseTcamResourceType: dgtSgtRegion(31), anyAnyRegion(32), tcamALabel(33), tcamBLabel(34), destInfoIn(35) and destInfoOut(36)." REVISION "200811110000Z" DESCRIPTION "Add new enumerations to cseTcamResourceType." REVISION "200801290000Z" DESCRIPTION "Add cseL3SwitchedPktsPerSecGroup. Add cseCacheStatisticsGroup. Add new enumerations to cseTcamResourceType. Add new enumerations to cseFlowIPFlowMask object." REVISION "200509160000Z" DESCRIPTION "Add cseFlowMcastMgmtGroup2. Deprecate the objects: cseFlowMcastQuerySrc, cseFlowMcastQueryGrp, cseFlowMcastResultGrp, cseFlowMcastResultSrc. Add new enumerations to cseFlowMcastQueryMask." REVISION "200504120000Z" DESCRIPTION "Add new enumerations to cseFlowIPFlowMask object. Add ingressInterfaceMapping and egressInterfaceMapping enumerations to cseTcamResourceType object." REVISION "200411150000Z" DESCRIPTION "Add cseMetUsageGroup." REVISION "200406090000Z" DESCRIPTION "Add the following Groups: cseNetflowASInfoExportGroup cseNetflowPerVlanIfGroup" REVISION "200311070000Z" DESCRIPTION "Add cseErrorStatsLCTable." REVISION "200308200000Z" DESCRIPTION "Add the following tables to support forwarding information base: cseCefFibTable, cseCefAdjacencyTable. Add the following table to support TCAM (Ternary Content Addressable Memory) resource usage: cseTcamUsageTable. Add default value for the following objects: cseFlowQuerySource, cseFlowQuerySourceMask, cseFlowQueryDestination, cseFlowQueryDestinationMask, cseFlowQueryOwner." REVISION "200306100000Z" DESCRIPTION "Deprecated the objects: cseNetflowLSExportHost, cseNetflowLSExportTransportNumber" REVISION "200305060000Z" DESCRIPTION "Added the object cseFlowQuerySkipNFlows" REVISION "200302210000Z" DESCRIPTION "Added the following objects and table: cseFlowLongAgingTime, cseNetFlowIfIndexEnable, cseFlowStatsTable, cseFlowExcludeTable. Modified the description of the following objects: cseL2IpPkts, cseL2IpxPkts, cseL2AssignedProtoPkts, cseL2OtherProtoPkts, cseL2HCIpPkts, cseL2HCIpxPkts, cseL2HCAssignedProtoPkts, cseL2HCOtherProtoPkts." REVISION "200208050000Z" DESCRIPTION "Added the following objects: cseFlowIPFlowMask, cseFlowIPXFlowMask, cseProtocolFilterEnable." REVISION "200202070000Z" DESCRIPTION "Added the objects in cseBridgedFlowStatsCtrlTable and cseErrorStatsTable. Added the following objects: cseL3VlanInUnicastPkts cseL3VlanInUnicastOctets cseL3VlanOutUnicastPkts cseL3VlanOutUnicastOctets." REVISION "200110260000Z" DESCRIPTION "Added the object cseFlowQueryTotalFlows" REVISION "200109130000Z" DESCRIPTION "Added the follwowing objects o cseNetflowLSFilterSupport o cseNetflowLSFilterTable. Also created the new groups o cseNDEMandatoryGroup o cseNDESingleFilterGroup o cseNDEMultipleFiltersGroup" REVISION "200105160000Z" DESCRIPTION "Added 4k Vlan support" REVISION "200103090000Z" DESCRIPTION "Update the range of cseFlowEstablishedAgingTime, cseFlowIPXEstablishedAgingTime, cseFlowOperEstablishedAgingTime, cseFlowOperIPXAgingTime. Replace cseFlowQueryResult with cseFlowQueryResultingRows." REVISION "200006230000Z" DESCRIPTION "Added the following objects: o cseFlowOperEstablishedAgingTime. o cseFlowOperFastAgingTime. o cseFlowOperFastAgePktThreshold. o cseFlowOperIPXAgingTime." REVISION "200001311130Z" DESCRIPTION "Added one High Capacity L2 Statistics table, an extension of cseL2StatsTable and new objects in NetflowLS group for new netflow export features. Also added a new enum type of cseRouterFlowMask to support L3 multicast." REVISION "9912091130Z" DESCRIPTION "Added MIB objects to manage Switch Engine (SE) portion of Multicast MLS control protocol." REVISION "9806241130Z" DESCRIPTION "Added 2 groups, for the purging (clearing) of layer 3 unicast and multicast flow entries stored in the cache. Also added new objects for layer 3 flow statistics." REVISION "9805281130Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 97 } -- Overview of MIB Objects: -- -- Defines 9 groups of objects. -- -- 1. cseL2Objects: Contains mainly Layer 2 statistics maintained by the -- switching engine hardware. -- -- 2. cseFlow: This group has all the important objects used in the -- management of switching engine hardware. It contains : -- - Scalars for configuring aging times that determine how long -- certain learned flows, are used for L3 switching its traffic. -- - A table of all routers whose "flows" are learned by the -- switching -- engine. -- - A table for adding external routers to the router table and -- enabling -- the switching engine to learn of all the flows through those -- routers. -- - A table listing the MAC address and VLAN number used for each -- router. -- - A query/result table pair for monitoring the switching -- performance -- of the switching engine(s). -- - A control table for enabling/disabling the flow switching -- feature -- per protocol type (ip, ipx). -- -- 3. cseNetflowLS: A group of objects used to manage -- the Netflow LAN Switching data export feature. -- -- 4. cseL3Objects: Contains -- - L3 statistics maintained by the switching engine hardware. -- - L3 packet/octets statistics (in/out) maintained per vlan. -- -- 5. cseProtocolFilter: Contains -- - Table for configuring protocol filters per (non-trunking) port. -- -- 6. cseUcastCache: Contains -- - a MIB table to perform actions of purging IP/IPX -- flows in switch engine cache pools. -- -- 7. cseMcastCache: -- - a MIB table to perform actions of purging IP -- multicast flows in switch engine caches. -- -- 8. cseCef: CEF (Cisco Express Forwarding) group. It contains: -- - tables provide information on IP forwarding database -- and statistics. -- -- 9. cseTcamUsage: Contains -- - table provides resource usage information on TCAM (Ternary -- Content Addressable Memory) in the device. -- -- 10. cseMet: MET group. It contains: -- - table provides resource usage information on MET (Multicast -- Expansion Table) in the device. cseMIBObjects OBJECT IDENTIFIER ::= { ciscoSwitchEngineMIB 1 } -- object groups cseL2Objects OBJECT IDENTIFIER ::= { cseMIBObjects 1 } cseFlow OBJECT IDENTIFIER ::= { cseMIBObjects 2 } cseNetflowLS OBJECT IDENTIFIER ::= { cseMIBObjects 3 } cseL3Objects OBJECT IDENTIFIER ::= { cseMIBObjects 4 } cseProtocolFilter OBJECT IDENTIFIER ::= { cseMIBObjects 5 } cseUcastCache OBJECT IDENTIFIER ::= { cseMIBObjects 6 } cseMcastCache OBJECT IDENTIFIER ::= { cseMIBObjects 7 } cseCef OBJECT IDENTIFIER ::= { cseMIBObjects 8 } cseTcamUsage OBJECT IDENTIFIER ::= { cseMIBObjects 9 } cseMet OBJECT IDENTIFIER ::= { cseMIBObjects 10 } CiscoGauge64 ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This TC describes an object with a nonnegative integer value that may increase or decrease, with a maximum value of 2^64-1." SYNTAX Counter64 ControlStatus ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This TC describes the current status of a controlled object value." SYNTAX INTEGER { enabled(1), disabled(2) } McastGroupIp ::= TEXTUAL-CONVENTION DISPLAY-HINT "1d.1d.1d.1d" STATUS current DESCRIPTION "This TC specifies an multicast group IP address, a class D IP address with the first byte in the range of 224 to 239." SYNTAX IpAddress FlowAddressComponent ::= TEXTUAL-CONVENTION DISPLAY-HINT "1x:" STATUS current DESCRIPTION "Represents a network layer address. The length and format of the address is protocol dependent as follows: ip 6 octets first 4 octets are the IP address in network order last 2 bytes is the transport's port number. ipx 10 octets first 4 octets are the net number last 6 octets are the host number" SYNTAX OCTET STRING (SIZE (6..6 | 10..10)) -- Layer 2 statistics per switching engine cseL2StatsTable OBJECT-TYPE SYNTAX SEQUENCE OF CseL2StatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing switching engine's L2 statistics counters." ::= { cseL2Objects 1 } cseL2StatsEntry OBJECT-TYPE SYNTAX CseL2StatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row containing L2 statistics maintained by a switching engine (identified by entPhysicalIndex). Each switching engine managed by this MIB module has an entry in this table." INDEX { entPhysicalIndex } ::= { cseL2StatsTable 1 } CseL2StatsEntry ::= SEQUENCE { cseL2ForwardedLocalPkts Counter32, cseL2ForwardedLocalOctets Counter64, cseL2ForwardedTotalPkts Counter32, cseL2NewAddressLearns Counter32, cseL2AddrLearnFailures Counter32, cseL2DstAddrLookupMisses Counter32, cseL2IpPkts Counter32, cseL2IpxPkts Counter32, cseL2AssignedProtoPkts Counter32, cseL2OtherProtoPkts Counter32 } cseL2ForwardedLocalPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets received from ports local to this switching engine and forwarded at layer 2." ::= { cseL2StatsEntry 1 } cseL2ForwardedLocalOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of octets in the packets received from ports local to this switching engine and forwarded at layer 2." ::= { cseL2StatsEntry 2 } cseL2ForwardedTotalPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of packets received from all sources (local and over the fabric) and forwarded at layer 2 by this switching engine." ::= { cseL2StatsEntry 3 } cseL2NewAddressLearns OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of new MAC addresses learned by the switching engine." ::= { cseL2StatsEntry 4 } cseL2AddrLearnFailures OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of MAC addresses failed to be learned because the L2 forwarding address table was full. If the value keeps increasing, the network topology should be reconfigured." ::= { cseL2StatsEntry 5 } cseL2DstAddrLookupMisses OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of misses during destination MAC address table lookups. A few misses happen normally. Large numbers of misses occur as a result of cseL2AddrLearnFailures." ::= { cseL2StatsEntry 6 } cseL2IpPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets belonging to the IP family received by this switching engine from all sources. This value includes L3 switched packets." ::= { cseL2StatsEntry 7 } cseL2IpxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets belonging to the IPX family received by this switching engine from all sources. This value includes L3 switched packets." ::= { cseL2StatsEntry 8 } cseL2AssignedProtoPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets belonging to an assigned group of network protocols (typically AppleTalk, DecNet and Vines) received by this switching engine from all sources. This value includes L3 switched packets." ::= { cseL2StatsEntry 9 } cseL2OtherProtoPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets belonging to all other protocol families, received by this switching engine from all sources. This value includes L3 switched packets." ::= { cseL2StatsEntry 10 } -- High Capacity extensions for cseL2StatsTable. cseL2StatsHCTable OBJECT-TYPE SYNTAX SEQUENCE OF CseL2StatsHCEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains the High Capacity L2 Statistics extensions to the cseL2StatsTable." ::= { cseL2Objects 2 } cseL2StatsHCEntry OBJECT-TYPE SYNTAX CseL2StatsHCEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains the High Capacity L2 Statistics extensions to cseL2StatsEntry. These objects will be created by the agent for all cseL2StatsEntries it deems appropriate." INDEX { entPhysicalIndex } ::= { cseL2StatsHCTable 1 } CseL2StatsHCEntry ::= SEQUENCE { cseL2HCOverflowForwardedLocalPkts Counter32, cseL2HCForwardedLocalPkts Counter64, cseL2HCOverflowForwardedTotalPkts Counter32, cseL2HCForwardedTotalPkts Counter64, cseL2HCOverflowIpPkts Counter32, cseL2HCIpPkts Counter64, cseL2HCOverflowIpxPkts Counter32, cseL2HCIpxPkts Counter64, cseL2HCOverflowAssignedProtoPkts Counter32, cseL2HCAssignedProtoPkts Counter64, cseL2HCOverflowOtherProtoPkts Counter32, cseL2HCOtherProtoPkts Counter64 } cseL2HCOverflowForwardedLocalPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the associated cseL2ForwardedLocalPkts counter has overflowed." ::= { cseL2StatsHCEntry 1 } cseL2HCForwardedLocalPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets received from ports local to this switching engine and forwarded at layer 2." ::= { cseL2StatsHCEntry 2 } cseL2HCOverflowForwardedTotalPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the associated cseL2ForwardeTotalPkts counter has overflowed." ::= { cseL2StatsHCEntry 3 } cseL2HCForwardedTotalPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of packets received from all sources (local and over the fabric) and forwarded at layer 2 by this switching engine." ::= { cseL2StatsHCEntry 4 } cseL2HCOverflowIpPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the associated cseL2IpPkts counter has overflowed." ::= { cseL2StatsHCEntry 5 } cseL2HCIpPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets belonging to the IP family received by this switching engine from all sources. This value includes L3 switched packets." ::= { cseL2StatsHCEntry 6 } cseL2HCOverflowIpxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the associated cseL2IpxPkts counter has overflowed." ::= { cseL2StatsHCEntry 7 } cseL2HCIpxPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets belonging to the IPX family received by this switching engine from all sources. This value includes L3 switched packets." ::= { cseL2StatsHCEntry 8 } cseL2HCOverflowAssignedProtoPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the associated cseL2HCAssignedProtoPkts counter has overflowed." ::= { cseL2StatsHCEntry 9 } cseL2HCAssignedProtoPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets belonging to an assigned group of network protocols (typically AppleTalk, DecNet and Vines) received by this switching engine from all sources. This value includes L3 switched packets." ::= { cseL2StatsHCEntry 10 } cseL2HCOverflowOtherProtoPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the associated cseL2HCOtherProtoPkts counter has overflowed." ::= { cseL2StatsHCEntry 11 } cseL2HCOtherProtoPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets belonging to all other protocol families, received by this switching engine from all sources. This value includes L3 switched packets." ::= { cseL2StatsHCEntry 12 } -- Flow group of objects -- -- Global aging times for the flows learned cseFlowEstablishedAgingTime OBJECT-TYPE SYNTAX Integer32 (1..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The adminstrative aging time for IP established flows. The default value for this object is implementation specific. If the cseFlowEstablishedAgingTime is not configured to the appropriate value, it will be adjusted to the closest value. The corresponding operational object, taken effect on the a device, is cseFlowOperIPEstablishedAgingTime." ::= { cseFlow 1 } cseFlowFastAgingTime OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The administrative fast aging time for the established flow entries, that have less number of packets than the value set in the cseFlowFastAgePktThreshold, switched within this time. Setting to value of 0 turns off fast aging. The default value for this object is implementation specific. If the cseFlowFastAgingTime is not configured to the appropriate value, it will be adjusted to the closest value. The corresponding operational object, taken effect on the device, is cseFlowOperFastAgingTime." ::= { cseFlow 2 } cseFlowFastAgePktThreshold OBJECT-TYPE SYNTAX Unsigned32 UNITS "packets" MAX-ACCESS read-write STATUS current DESCRIPTION "The administrative packet threshold setting for the cseFlowFastAgingTime. The default for Fast Aging Packet Threshold is 0, i.e. no packets switched within the time set in cseFlowFastAgingTime, after an L3 flow was established. If the cseFlowFastAgingTime is not configured to the appropriate value, it will be adjusted to the closest value. The corresponding operational object, taken effect on the device, is cseFlowOperFastAgePktThreshold." ::= { cseFlow 3 } -- Router Table cseRouterTable OBJECT-TYPE SYNTAX SEQUENCE OF CseRouterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing information about all routers that are discovered by the switch, including internal and external routers." ::= { cseFlow 4 } cseRouterEntry OBJECT-TYPE SYNTAX CseRouterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the cseRouterTable containing information about a router. A row appears either directly through dynamic learning or indirectly through management configuration (via SNMP,by creating an entry in the cseStaticExtRouterTable or via CLI)." INDEX { cseRouterIndex } ::= { cseRouterTable 1 } CseRouterEntry ::= SEQUENCE { cseRouterIndex IpAddress, cseRouterFlowMask INTEGER, cseRouterName DisplayString, cseRouterStatic TruthValue, cseRouterIpxFlowMask INTEGER } cseRouterIndex OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The router's IP address which is used to uniquely identify it for L3 flows." ::= { cseRouterEntry 1 } cseRouterFlowMask OBJECT-TYPE SYNTAX INTEGER { dstOnly(1), srcDst(2), fullFlow(3), notApplicable(4), srcDstVlan(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The IP type of mask configured for the router represented by this row. Each flow known to the switching engine has a mask which is applied to all packets in order to compare them to that flow. Each hardware-learned flow has the mask configured for the router which logically forwards that flow." ::= { cseRouterEntry 2 } cseRouterName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "DNS name (if available) of the router." ::= { cseRouterEntry 3 } cseRouterStatic OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "If the value of the object is true, this router was configured via SNMP or CLI. Otherwise, this router was learned automatically." ::= { cseRouterEntry 4 } cseRouterIpxFlowMask OBJECT-TYPE SYNTAX INTEGER { dstOnly(1), srcDst(2), fullFlow(3), notApplicable(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The IPX type of mask configured for the router represented by this row. Each flow known to the switching engine has a mask which is applied to all packets in order to compare them to that flow. Each hardware-learned flow has the mask configured for the router which logically forwards that flow." ::= { cseRouterEntry 5 } -- Table of external routers that are enabled. cseStaticExtRouterTable OBJECT-TYPE SYNTAX SEQUENCE OF CseStaticExtRouterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of external routers which are enabled for Layer 3 IP switching by the switching engine. This table may contain routers that have not yet been discovered by the device." ::= { cseFlow 5 } cseStaticExtRouterEntry OBJECT-TYPE SYNTAX CseStaticExtRouterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the cseStaticExtRouterTable for enabling an external router to be installed in the switch's router table. The entry is created and deleted by using cseStaticRouterStatus." INDEX { cseRouterIndex } ::= { cseStaticExtRouterTable 1 } CseStaticExtRouterEntry ::= SEQUENCE { cseStaticRouterName DisplayString, cseStaticRouterOwner OwnerString, cseStaticRouterStatus RowStatus, cseStaticRouterType BITS } cseStaticRouterName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "DNS name (if available) of the external router." ::= { cseStaticExtRouterEntry 1 } cseStaticRouterOwner OBJECT-TYPE SYNTAX OwnerString MAX-ACCESS read-create STATUS current DESCRIPTION "String indicating the owner who created the static entry." ::= { cseStaticExtRouterEntry 2 } cseStaticRouterStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Used to manage creation and deletion of rows in this table. Once a row becomes active, values within that row cannot be modified except by deleting and creating the row." ::= { cseStaticExtRouterEntry 3 } -- per Router, per VLAN MAC address table for the flows cseStaticRouterType OBJECT-TYPE SYNTAX BITS { unicast(0), multicast(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates if the router is included for unicast switching, or multicast switching, or both." DEFVAL { { unicast } } ::= { cseStaticExtRouterEntry 4 } cseRouterVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF CseRouterVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table listing the MAC address used by routers on particular VLANs." ::= { cseFlow 6 } cseRouterVlanEntry OBJECT-TYPE SYNTAX CseRouterVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of the cseRouterVlanTable. An entry exists for each known VLAN of each known router." INDEX { cseRouterIndex, cseRouterMac, cseRouterVlan } ::= { cseRouterVlanTable 1 } CseRouterVlanEntry ::= SEQUENCE { cseRouterMac MacAddress, cseRouterVlan VlanIndex, cseRouterProtocol BITS } cseRouterMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Mac address used by the router for this VLAN number." ::= { cseRouterVlanEntry 1 } cseRouterVlan OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Vlan number associated with the router's MAC address." ::= { cseRouterVlanEntry 2 } cseRouterProtocol OBJECT-TYPE SYNTAX BITS { ip(0), ipx(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates which protocols are routed by this router on this VLAN using this Mac address." ::= { cseRouterVlanEntry 3 } -- Unicast Flow Query table cseFlowMaxQueries OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum number of query entries allowed to be outstanding at any time, in the cseFlowQueryTable. The typical value for this object is 5." ::= { cseFlow 7 } cseFlowQueryTable OBJECT-TYPE SYNTAX SEQUENCE OF CseFlowQueryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A control table used to query the switching engine by specifying retrieval criteria for L3 flows. The resulting data for each instance of a query in this table is returned in the cseFlowDataTable. The maximum number of entries (rows) in this table cannot exceed the value returned by cseFlowMaxQueries." ::= { cseFlow 8 } cseFlowQueryEntry OBJECT-TYPE SYNTAX CseFlowQueryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of the cesFlowQueryTable used to setup retrieval criteria to search for L3 flows on a particular switching engine entity identified by entPhysicalIndex. The actual search is started by setting the value of cseFlowQueryStatus to 'active'. Once a row becomes active, values within the row cannot be modified, except by deleting and re-creating the row." INDEX { entPhysicalIndex, cseFlowQueryIndex } ::= { cseFlowQueryTable 1 } CseFlowQueryEntry ::= SEQUENCE { cseFlowQueryIndex Unsigned32, cseFlowQueryMask INTEGER, cseFlowQueryTransport BITS, cseFlowQuerySource FlowAddressComponent, cseFlowQuerySourceMask FlowAddressComponent, cseFlowQueryDestination FlowAddressComponent, cseFlowQueryDestinationMask FlowAddressComponent, cseFlowQueryRouterIndex IpAddress, cseFlowQueryOwner OwnerString, cseFlowQueryResultingRows Integer32, cseFlowQueryResultTotalPkts CiscoGauge64, cseFlowQueryResultTotalOctets CiscoGauge64, cseFlowQueryResultAvgDuration TimeInterval, cseFlowQueryResultAvgIdle TimeInterval, cseFlowQueryStatus RowStatus, cseFlowQueryCreateTime TimeStamp, cseFlowQueryTotalFlows Unsigned32, cseFlowQuerySkipNFlows Integer32 } cseFlowQueryIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer which uniquely identifies the control query among all those specified for the switching engine indicated by entPhysicalIndex." ::= { cseFlowQueryEntry 1 } cseFlowQueryMask OBJECT-TYPE SYNTAX INTEGER { dstOnly(1), srcOrDst(2), srcAndDst(3), fullFlow(4), ipxDstOnly(5), ipxSrcAndDst(6), any(7) } MAX-ACCESS read-create STATUS current DESCRIPTION "Setting each value causes the appropriate action: 'dstOnly' - causes the creation of rows in the cseFlowDataTable corresponding to the current L3 flow information for the absolute destination IP address set in the cseFlowQueryDestination object in this table. If cseFlowQueryDestinationMask is also specified at the same time, it will be applied to the address part of cseFlowQueryDestination. 'srcOrDst' - causes the creation of rows in the cseFlowDataTable corresponding to the current L3 flow information for EITHER of the absolute IP addresses set in the cseFlowQueryDestination or cseFlowQuerySource objects. If either of cseFlowQueryDestinationMask and cseFlowQuerySourceMask objects are also specified at the same time, they will be applied to the respective address parts of cseFlowQueryDestination and cseFlowQuerySource objects. This option is typically used to setup queries for flows on traffic in either directions. 'srcAndDst' - causes the creation of rows in the cseFlowDataTable corresponding to the current L3 flow information for BOTH the absolute IP addresses set in the cseFlowQueryDestination and cseFlowQuerySource objects. If either of cseFlowQueryDestinationMask and cseFlowQuerySourceMask objects are also specified at the same time, they will be applied to the respective address parts of cseFlowQueryDestination and cseFlowQuerySource objects. This option is typically used to setup queries for flows on traffic in one direction only. 'fullFlow' - causes the creation of row(s) in the cseFlowDataTable exactly corresponding to the current L3 flow information for the complete IP flow (including the transport port numbers) set in the cseFlowQueryDestination and cseFlowQuerySource objects. If either of cseFlowQueryDestinationMask and cseFlowQuerySourceMask objects are also specified at the same time, they will be applied to the respective address parts of cseFlowQueryDestination and cseFlowQuerySource objects. This option is typically used to setup queries for flows on traffic for specific (TCP/UDP) port numbers corresponding to standard protocols such as FTP, WWW, TELNET, etc. 'ipxDstOnly' - causes the creation of rows in the cseFlowDataTable corresponding to the current L3 flow information for the absolute destination IPX address set in the cseFlowQueryDestination object in this table. If cseFlowQueryDestinationMask is also specified at the same time, it will be applied to the address part of cseFlowQueryDestination. 'ipxSrcAndDst' - causes the creation of rows in the cseFlowDataTable corresponding to the current L3 flow information for BOTH the absolute IPX addresses set in the cseFlowQueryDestination and cseFlowQuerySource objects. If either of cseFlowQueryDestinationMask and cseFlowQuerySourceMask objects are also specified at the same time, they will be applied to the respective address parts of cseFlowQueryDestination and cseFlowQuerySource objects. 'any' - returns all rows corresponding to all established flow entries in the cseFlowDataTable. Note: 1. The type FlowAddressComponent used for objects cseFlowQuerySource and cseFlowQueryDestination, has the network address part and also the transport port number part, if applicable. 2. The value of this object cannot be modified when the corresponding instance of cseFlowQueryStatus is 'active'." DEFVAL { any } ::= { cseFlowQueryEntry 2 } cseFlowQueryTransport OBJECT-TYPE SYNTAX BITS { udp(0), tcp(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "The IP transport protocol type specified for this query. Ignored for IPX flow queries. The value of this object cannot be modified when the corresponding instance of cseFlowQueryStatus is 'active'." DEFVAL { { udp , tcp } } ::= { cseFlowQueryEntry 3 } cseFlowQuerySource OBJECT-TYPE SYNTAX FlowAddressComponent MAX-ACCESS read-create STATUS current DESCRIPTION "The source network address and port (if applicable). The value of this object cannot be modified when the corresponding instance of cseFlowQueryStatus is 'active'." DEFVAL { '000000000000'H } ::= { cseFlowQueryEntry 4 } cseFlowQuerySourceMask OBJECT-TYPE SYNTAX FlowAddressComponent MAX-ACCESS read-create STATUS current DESCRIPTION "The source address mask to be applied to the corresponding instance of cseFlowQuerySource. The value of this object cannot be modified when the corresponding instance of cseFlowQueryStatus is 'active'." DEFVAL { 'FFFFFFFFFFFF'H } ::= { cseFlowQueryEntry 5 } cseFlowQueryDestination OBJECT-TYPE SYNTAX FlowAddressComponent MAX-ACCESS read-create STATUS current DESCRIPTION "The destination network address and port (if applicable). The value of this object cannot be modified when the corresponding instance of cseFlowQueryStatus is 'active'." DEFVAL { '000000000000'H } ::= { cseFlowQueryEntry 6 } cseFlowQueryDestinationMask OBJECT-TYPE SYNTAX FlowAddressComponent MAX-ACCESS read-create STATUS current DESCRIPTION "The destination address mask to be applied to the corresponding instance of cseFlowQueryDestination. The value of this object cannot be modified when the corresponding instance of cseFlowQueryStatus is 'active'." DEFVAL { 'FFFFFFFFFFFF'H } ::= { cseFlowQueryEntry 7 } cseFlowQueryRouterIndex OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "Index of the router for which the flows are available. An 'all-zero' IP address indicates that the query is for any router. The value of this object cannot be modified when the corresponding instance of cseFlowQueryStatus is 'active'." ::= { cseFlowQueryEntry 8 } cseFlowQueryOwner OBJECT-TYPE SYNTAX OwnerString MAX-ACCESS read-create STATUS current DESCRIPTION "The manager entity that configured this entry and is therefore using the resources assigned to it." DEFVAL { "" } ::= { cseFlowQueryEntry 9 } cseFlowQueryResultingRows OBJECT-TYPE SYNTAX Integer32 (-1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The result status of the query. Possible values are: -1 - Either the query has not been initiated or the agent is busy processing this query instance. Time to completion of the query processing depends on the complexity of the query and the number of matches that satisfy this query. 0..2147483647 - The search has ended and this is the number of rows in the cseFlowDataTable, resulting from this query." ::= { cseFlowQueryEntry 10 } cseFlowQueryResultTotalPkts OBJECT-TYPE SYNTAX CiscoGauge64 MAX-ACCESS read-only STATUS current DESCRIPTION "The aggregate number of total packets switched by the system on all the flows matching this query. This is a snapshot value and is valid only when the corresponding instance of cseFlowQueryResultingRows is greater than or equal to 0." ::= { cseFlowQueryEntry 11 } cseFlowQueryResultTotalOctets OBJECT-TYPE SYNTAX CiscoGauge64 MAX-ACCESS read-only STATUS current DESCRIPTION "The aggregate number of total octets switched by the system on all the flows matching this query. This is a snapshot value and is valid only when the corresponding instance of cseFlowQueryResultingRows is greater than or equal to 0." ::= { cseFlowQueryEntry 12 } cseFlowQueryResultAvgDuration OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-only STATUS current DESCRIPTION "The average duration of the flows matching this query. This is a snapshot value and is valid only when the corresponding instance of cseFlowQueryResultingRows is greater than or equal to 0." ::= { cseFlowQueryEntry 13 } cseFlowQueryResultAvgIdle OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-only STATUS current DESCRIPTION "The elapsed time since the flows were last used, averaged over all flows matching this query. This is a snapshot value and is valid only when the corresponding instance of cseFlowQueryResultingRows is greater than or equal to 0." ::= { cseFlowQueryEntry 14 } cseFlowQueryStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status object used to manage rows in this table. When set to active(1), the query is initiated. Once initiated, the value may not be modified until the value of cseFlowQueryResultingRows is greater than or equal to 0. However, this object can be set to active(1) only after all the appropriate objects for this query as defined by the value set in the cseFlowQueryMask object, have also been set. Once a row becomes active, values within the row cannot be modified, except by deleting and re-creating it." ::= { cseFlowQueryEntry 15 } cseFlowQueryCreateTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "Time when this query was created." ::= { cseFlowQueryEntry 16 } cseFlowQueryTotalFlows OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of L3 flows matching the query criterion." ::= { cseFlowQueryEntry 17 } cseFlowQuerySkipNFlows OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "The number of searched flows to be skipped before storing any L3 flows in cseFlowDataTable. This object can be used along with cseFloQueryTotalFlows object to skip previously found flows by setting the variable equal to the number of the associated rows in cseFlowDataTable, and only query the remaining flows in the table. Note that due to the dynamical nature of the L3 flows, the queried flows may be missed or repeated by setting this object. The value of this object cannot be modified when the corresponding instance of cseFlowQueryStatus is 'active'." DEFVAL { 0 } ::= { cseFlowQueryEntry 18 } -- The Unicast Flow query results data table cseFlowDataTable OBJECT-TYPE SYNTAX SEQUENCE OF CseFlowDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing L3 flow information corresponding to all the completed queries setup in the cseFlowQueryTable, that were initiated on the switch engine(s)." ::= { cseFlow 9 } cseFlowDataEntry OBJECT-TYPE SYNTAX CseFlowDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of the cseFlowDataTable used to return information about one of the L3 flows which matched the search criteria set by the cseFlowQueryMask object in the corresponding instance of the cseFlowQueryTable." INDEX { entPhysicalIndex, cseFlowQueryIndex, cseFlowDataIndex } ::= { cseFlowDataTable 1 } CseFlowDataEntry ::= SEQUENCE { cseFlowDataIndex Unsigned32, cseFlowDataSrcMac MacAddress, cseFlowDataDstMac MacAddress, cseFlowDataStaticFlow TruthValue, cseFlowDataEncapType INTEGER, cseFlowDataSource FlowAddressComponent, cseFlowDataDestination FlowAddressComponent, cseFlowDataDestVlan VlanIndex, cseFlowDataIpQOS Integer32, cseFlowDataIpQOSPolicy Integer32, cseFlowDataWhenCreated TimeStamp, cseFlowDataLastUsed TimeStamp, cseFlowDataPkts Gauge32, cseFlowDataOctets CiscoGauge64 } cseFlowDataIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number to uniquely identify a result entry that matches a particular query for a specific switching engine." ::= { cseFlowDataEntry 1 } cseFlowDataSrcMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Source Mac Address of the router's outgoing interface." ::= { cseFlowDataEntry 2 } cseFlowDataDstMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Destination Mac Address used to forward the packets in this flow." ::= { cseFlowDataEntry 3 } cseFlowDataStaticFlow OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether this flow was software-installed." ::= { cseFlowDataEntry 4 } cseFlowDataEncapType OBJECT-TYPE SYNTAX INTEGER { ipArpa(1), ipxEthernet(2), ipx802raw(3), ipx802sap(4), ipx802snap(5), other(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "Protocol encapsulation type used to forward packets in this flow to their destination." ::= { cseFlowDataEntry 5 } cseFlowDataSource OBJECT-TYPE SYNTAX FlowAddressComponent MAX-ACCESS read-only STATUS current DESCRIPTION "The source network address and the port (if appropriate) of this flow." ::= { cseFlowDataEntry 6 } cseFlowDataDestination OBJECT-TYPE SYNTAX FlowAddressComponent MAX-ACCESS read-only STATUS current DESCRIPTION "The destination network address and port (if appropriate) of this flow." ::= { cseFlowDataEntry 7 } cseFlowDataDestVlan OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The vlan number on which packets belonging to this flow are forwarded." ::= { cseFlowDataEntry 8 } cseFlowDataIpQOS OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "Level of Quality of service for this IP flow. If it is not an IP flow, this object will not be instantiated." ::= { cseFlowDataEntry 9 } cseFlowDataIpQOSPolicy OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "Level of the Quality of service policy for this IP flow. If it is not an IP flow, this object will not be instantiated." ::= { cseFlowDataEntry 10 } cseFlowDataWhenCreated OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "Time when this flow was created in the switching engine." ::= { cseFlowDataEntry 11 } cseFlowDataLastUsed OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "Time since this flow was last used to forward a packet by the switching engine." ::= { cseFlowDataEntry 12 } cseFlowDataPkts OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "A snapshot value of the number of packets forwarded on this flow at the time of corresponding query." ::= { cseFlowDataEntry 13 } cseFlowDataOctets OBJECT-TYPE SYNTAX CiscoGauge64 MAX-ACCESS read-only STATUS current DESCRIPTION "A snapshot value of octets forwarded on this flow at the time of corresponding query." ::= { cseFlowDataEntry 14 } cseFlowSwitchControlTable OBJECT-TYPE SYNTAX SEQUENCE OF CseFlowSwitchControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table used to control the L3 flow switching operation, per protocol type." ::= { cseFlow 10 } cseFlowSwitchControlEntry OBJECT-TYPE SYNTAX CseFlowSwitchControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row for the configuration of Flow switching feature for an L3 protocol type." INDEX { cseFlowSwitchProtocol } ::= { cseFlowSwitchControlTable 1 } CseFlowSwitchControlEntry ::= SEQUENCE { cseFlowSwitchProtocol CiscoNetworkProtocol, cseFlowSwitchStatus ControlStatus } cseFlowSwitchProtocol OBJECT-TYPE SYNTAX CiscoNetworkProtocol MAX-ACCESS not-accessible STATUS current DESCRIPTION "Protocol type for which this row instance. Only ip(1) and ipx(14) values are currently supported." ::= { cseFlowSwitchControlEntry 1 } cseFlowSwitchStatus OBJECT-TYPE SYNTAX ControlStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The current status of the global flow switching capability for the specified L3 protocol type." ::= { cseFlowSwitchControlEntry 2 } -- Multicast Flow Query table cseFlowMcastMaxQueries OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum number of query entries allowed to be outstanding at any time, in the cseFlowMcastQueryTable. The typical value for this object is 5." ::= { cseFlow 11 } cseFlowMcastQueryTable OBJECT-TYPE SYNTAX SEQUENCE OF CseFlowMcastQueryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A control table used to query the switching engine by specifying retrieval criteria for IP multicast L3 flows. Each row instance in the table represents a query with its parameters. The resulting data for each instance of a query in this table is returned in the cseFlowMcastResultTable. The maximum number of entries (rows) in this table cannot exceed the value of cseFlowMcastMaxQueries object. Unlike unicast switched layer 3 flows, an IP multicast switched flow is created and installed by software, and is uniquely identified by flow's source IP address, and multicast group IP address. It is stored with input Vlan ID in the cache entry, so that the packets in the flow will not be replicated and forwarded to the receivers on the same (input) Vlan. Another difference is that all IP multicast hardware switched flows belonging to the same (source, group) are stored only on one switch engine on a Cisco L3 switch with distributed switch engines, whereas unicast flows identified by certain criterion may resident on multiple switch engines in the system." ::= { cseFlow 12 } cseFlowMcastQueryEntry OBJECT-TYPE SYNTAX CseFlowMcastQueryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of the cesMcastFlowQueryTable used to setup retrieval criteria to search for IP multicast L3 flows on all switching engine entities in the device. The actual search is started by setting the value of cseFlowMcastQueryStatus to 'active'. Once a row becomes active, values within the row cannot be modified, without setting the associated RowStatus object to 'notInService' first, or deleting and re-creating the row." INDEX { cseFlowMcastQueryIndex } ::= { cseFlowMcastQueryTable 1 } CseFlowMcastQueryEntry ::= SEQUENCE { cseFlowMcastQueryIndex Unsigned32, cseFlowMcastQueryMask BITS, cseFlowMcastQuerySrc IpAddress, cseFlowMcastQueryGrp McastGroupIp, cseFlowMcastQuerySrcVlan VlanIndex, cseFlowMcastQueryRtrIndex IpAddress, cseFlowMcastQuerySkipNFlows Integer32, cseFlowMcastQueryOwner OwnerString, cseFlowMcastQueryTotalFlows Integer32, cseFlowMcastQueryRows Integer32, cseFlowMcastQueryStatus RowStatus, cseFlowMcastQueryCreateTime TimeStamp, cseFlowMcastQueryMvrf MplsVpnId, cseFlowMcastQueryAddrType InetAddressType, cseFlowMcastQuerySource InetAddress, cseFlowMcastQueryGroup InetAddress } cseFlowMcastQueryIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer in the range of 1 to cseFlowMcastMaxQueries to identify this control query." ::= { cseFlowMcastQueryEntry 1 } cseFlowMcastQueryMask OBJECT-TYPE SYNTAX BITS { source(0), group(1), vlan(2), router(3), mvrf(4), sourceip(5), groupip(6) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to set up the query criterion for the multicast flows of interest. If any one of the defined BITs is set, then the value of the corresponding object in the same row instance will be used for the search. Specifically, if the 'source(0)' BIT is set, then the cseFlowMcastQuerySrc object will be included in the search criterion. If the group(1) BIT is set, then the cseFlowMcastQueryGrp object will be included in the search criterion. If the vlan(2) BIT is set, then the cseFlowMcastQuerySrcVlan object will be included in the search criterion. If the router(3) BIT is set, then the cseFlowMcastQueryRtrIndex object will be included in the search criterion. If the mvrf(4) BIT is set, then the cseFlowMcastQueryMvrf object will be included in the search criterion; If the sourceip(5) BIT is set, then the cseFlowMcastQueryAddrType and cseFlowMcastQuerySource objects will be included in the search criterion. If the groupip(6) BIT is set, then the cseFlowMcastQueryAddrType and cseFlowMcastQueryGroup objects will be included in the search criterion. If the source(0) or group(1) BIT is set, then the sourceip(5) or groupip(6) cannot be set, and vice-versa. If any of the BITs in this variable is cleared, the corresponding parameter object in the same row is treated as a wildcard. When the row is instantiated, the BITs in the variable will be cleared, and none of query parameter objects in this row will be instantiated. This will be considered as a wildcard search for flows on the default Multicast Virtual Private Network (MVPN) routing/forwarding (MVRF) instance. i.e. it will return all rows corresponding to all established multicast flow entries in the default MVRF, in cseFlowMcastResultTable. The address type of this wildcard search will be specified be cseFlowMcastQueryAddrType. It is SNMP managers' responsibility to set certain bits on in this object instance, if necessary, and the corresponding flow parameter variables to the appropriate values in order to setup the desired query criteria. The value of this object can not be altered when the corresponding instance of cseFlowMcastQueryStatus is 'active'." DEFVAL { { } } ::= { cseFlowMcastQueryEntry 2 } cseFlowMcastQuerySrc OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The source address of the IP multicast layer 3 flows. This object should be instantiated and assigned a proper IP address whenever the 'source' bit of cseFlowMcastQueryMask object in the same row is on. If the 'source' bit is set, and an appropriate IP address is assigned to this object, then only flows with the specified source address will be containing in the result table. If the 'source' bit in the associated cseFlowMcastQueryMask is cleared, this object is ignored during the query, and all flows will be considered regardless of their source IP address. This object is deprecated and replaced by cseFlowMcastQueryAddrType and cseFlowMcastQuerySource." ::= { cseFlowMcastQueryEntry 3 } cseFlowMcastQueryGrp OBJECT-TYPE SYNTAX McastGroupIp MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The IP multicast group address of the queried flows. This object should be instantiated and set whenever the 'group' bit of the associated cseFlowMcastQueryMask object is on. If the 'group' bit is set, and a multicast group address is assigned to the object, only flows with the specified group address will be contained in the result table. If the 'group' bit in the associated cseFlowMcastQueryMask is cleared, this object is ignored during the query, and all flows will be considered regardless of their group address. This object is deprecated and replaced by cseFlowMcastQueryAddrType and cseFlowMcastQueryGroup." ::= { cseFlowMcastQueryEntry 4 } cseFlowMcastQuerySrcVlan OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-create STATUS current DESCRIPTION "The source Vlan ID of the IP multicast layer 3 flows. This object should be instantiated and set whenever the 'vlan' bit of the associated cseFlowMcastQueryMask object is on. If the 'vlan' bit is set, and a Vlan ID is assigned to this object, only flows belonging to that vlan will be contained in the result table. If the 'vlan' bit in the associated cseFlowMcastQueryMask object is cleared, this object is ignored during the query, and all flows will be considered regardless of their vlan IDs." ::= { cseFlowMcastQueryEntry 5 } cseFlowMcastQueryRtrIndex OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "Index of the router for which the multicast flows are available, that is the flows would be replicated and routed by the specified router, should the flows did not get switched. This object should be instantiated and set whenever the 'router' bit of the asociated cseFlowMcastQueryMask object is on. If the 'router' bit is set, and a router's IP address is assigned to this object, then only flows associated with that router will be contained in the result table. If the 'router' bit in the cseFlowMcastQueryMask object is cleared, this object is ignored during the query, and all flows will be considered regardless of the routers being switched." ::= { cseFlowMcastQueryEntry 6 } cseFlowMcastQuerySkipNFlows OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "The number of searched flows to be skipped before storing any multicast flows in cseFlowMcastResultTable. This object can be used along with cseFlowMcastQueryTotalFlows object to skip previously found flows by setting the variable equal to the number of the associated rows in cseFlowMcastResultTable, and only query the remaining flows in the table. Note that due to the dynamical nature of the L3 flows, the queried flows may be missed or repeated by setting this object." DEFVAL { 0 } ::= { cseFlowMcastQueryEntry 7 } cseFlowMcastQueryOwner OBJECT-TYPE SYNTAX OwnerString MAX-ACCESS read-create STATUS current DESCRIPTION "The manager entity that configured this entry and is therefore using the resources assigned to it. It is used to model an administratively assigned name of the owner of a resource. It is recommended that this object have one or more the following information: IP address, management station name, network manager's name, location, or phone number." ::= { cseFlowMcastQueryEntry 8 } cseFlowMcastQueryTotalFlows OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of flows matching the query criterion." ::= { cseFlowMcastQueryEntry 9 } cseFlowMcastQueryRows OBJECT-TYPE SYNTAX Integer32 (-1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "Indicating the status of the query by following values: -1 - Either the query has not been started or the agent is still processing this query instance. It is the default value when the row is instantiated. 0..2147483647 - The search has ended and this is the number of rows in the cseFlowMcastResultTable, resulting from this query." ::= { cseFlowMcastQueryEntry 10 } cseFlowMcastQueryStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status object used to manage rows in this table. When set to 'active', the query of flows is initiated. This object can be set to active only after all the appropriate objects for this query as defined by the bits in the cseFlowMcastQueryMask object, have also been instantiated. The completion of the query is indicated by the value of cseFlowMcastQueryRows as soon as it becomes greater than or equal to 0. Once a row becomes active, values within the row cannot be modified without setting it to 'notInService' first, or just deleting and re-creating it. To abort a lengthy on-going query, setting this object to 'notInService', or 'destroy' will terminate a search if one is in progress, and cause the associated rows in cseFlowMcastResultTable, if any, to be deleted." ::= { cseFlowMcastQueryEntry 11 } cseFlowMcastQueryCreateTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "Time when this query was last set to active." ::= { cseFlowMcastQueryEntry 12 } cseFlowMcastQueryMvrf OBJECT-TYPE SYNTAX MplsVpnId MAX-ACCESS read-create STATUS current DESCRIPTION "The human-readable name of the Multicast Virtual Private Network (MVPN) routing/forwarding instance (MVRF). When the 'mvrf' bit of cseFlowMcastQueryMask object in the same row is on, an appropriate value should be specified and only flows with the specified MVRF name will be contained in the result table. If the 'mvrf' bit in the associated cseFlowMcastQueryMask is cleared, this object is ignored during the query, and all the flows corresponding to the default MVRF will be considered." ::= { cseFlowMcastQueryEntry 13 } cseFlowMcastQueryAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "The Internet address type for this multicast search query." DEFVAL { ipv4 } ::= { cseFlowMcastQueryEntry 14 } cseFlowMcastQuerySource OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The source Internet address of the IP multicast layer 3 flows. When the 'sourceip' bit of cseFlowMcastQueryMask cseFlowMcastQueryMask object in the same row is on, an appropriate value should be specified and only flows with the specified source address will be contained in the result table. If the 'sourceip' bit in the associated cseFlowMcastQueryMask is cleared, this object is ignored during the query, and all flows will be considered regardless of their source address. The type of this address is determined by the value of the cseFlowMcastQueryAddrType object. The default value of this object is all zeros." DEFVAL { '00000000'H } ::= { cseFlowMcastQueryEntry 15 } cseFlowMcastQueryGroup OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The multicast group Internet address of the queried flows. When the 'mvrf' bit of cseFlowMcastQueryMask object in the same row is on, an appropriate value should be specified and only flows with the specified group address will be contained in the result table. If the 'groupip' bit in the associated cseFlowMcastQueryMask is cleared, this object is ignored during the query, and all flows will be considered regardless of their group address. The type of this address is determined by the value of the cseFlowMcastQueryAddrType object. The default value of this object is all zeros." DEFVAL { '00000000'H } ::= { cseFlowMcastQueryEntry 16 } -- The multicast flow query result data table cseFlowMcastResultTable OBJECT-TYPE SYNTAX SEQUENCE OF CseFlowMcastResultEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing current IP multicast flow information corresponding to all the completed queries set up in the cseFlowMcastQueryTable, that were initiated on the switch engine(s). The query result will not become available until the current search completes." ::= { cseFlow 13 } cseFlowMcastResultEntry OBJECT-TYPE SYNTAX CseFlowMcastResultEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of cseFlowMcastResultTable, containing information about an IP multicast layer 3 flow that matchs the search criteria set in the corresponding row of cseFlowMcastQueryTable. This row instance is indexed by the query index (cseFlowMcastQueryIndex), the switch engine entity (entPhysicalIndex), and data entry index (cseFlowMcastResultIndex). The value of entPhysicalIndex object is assigned by Entity-MIB, and uniquely identifies a switching engine on which the IP multicast flow is stored." INDEX { cseFlowMcastQueryIndex, entPhysicalIndex, cseFlowMcastResultIndex } ::= { cseFlowMcastResultTable 1 } CseFlowMcastResultEntry ::= SEQUENCE { cseFlowMcastResultIndex Integer32, cseFlowMcastResultGrp McastGroupIp, cseFlowMcastResultSrc IpAddress, cseFlowMcastResultSrcVlan VlanIndex, cseFlowMcastResultRtrIp IpAddress, cseFlowMcastResultRtrMac MacAddress, cseFlowMcastResultCreatedTS TimeStamp, cseFlowMcastResultLastUsedTS TimeStamp, cseFlowMcastResultPkts Counter64, cseFlowMcastResultOctets Counter64, cseFlowMcastResultDstVlans OCTET STRING, cseFlowMcastResultDstVlans2k OCTET STRING, cseFlowMcastResultDstVlans3k OCTET STRING, cseFlowMcastResultDstVlans4k OCTET STRING, cseFlowMcastResultMvrf MplsVpnId, cseFlowMcastResultAddrType InetAddressType, cseFlowMcastResultGroup InetAddress, cseFlowMcastResultSource InetAddress, cseFlowMcastResultFlowType INTEGER, cseFlowMcastResultHFlag1k2k OCTET STRING, cseFlowMcastResultHFlag3k4k OCTET STRING } cseFlowMcastResultIndex OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A positive integer which uniquely identify a result entry on a specific switching engine matching a particular query." ::= { cseFlowMcastResultEntry 1 } cseFlowMcastResultGrp OBJECT-TYPE SYNTAX McastGroupIp MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The multicast group IP address of the multicast layer 3 flow. This object is deprecated and replaced by cseFlowMcastResultAddrType and cseFlowMcastResultGroup." ::= { cseFlowMcastResultEntry 2 } cseFlowMcastResultSrc OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The source address of the multicast layer 3 flow. This object is deprecated and replaced by cseFlowMcastResultAddrType and cseFlowMcastResultSource." ::= { cseFlowMcastResultEntry 3 } cseFlowMcastResultSrcVlan OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The source Vlan ID of the IP multicast layer 3 flow." ::= { cseFlowMcastResultEntry 4 } cseFlowMcastResultRtrIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The interface IP address of the router this multicast flow is switching for. Since IP multicast flows can only be established for a router's trunk ports, it is the primary IP address of the router's trunk link that connects to the switch." ::= { cseFlowMcastResultEntry 5 } cseFlowMcastResultRtrMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The default MAC address of the router the multicast flow is switching for. Different multicast flows switching different ports of the same router will have the identical value of this object." ::= { cseFlowMcastResultEntry 6 } cseFlowMcastResultCreatedTS OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "Time when the IP multicast flow was created." ::= { cseFlowMcastResultEntry 7 } cseFlowMcastResultLastUsedTS OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "Time when this IP multicast flow was last used." ::= { cseFlowMcastResultEntry 8 } cseFlowMcastResultPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of multicast traffic packets forwarded for this flow (replicated packets are not counted)." ::= { cseFlowMcastResultEntry 9 } cseFlowMcastResultOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of multicast traffic octets forwarded for this flow (replicated packets are not counted)." ::= { cseFlowMcastResultEntry 10 } cseFlowMcastResultDstVlans OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN. Each octet within the value of this object specifies a set of eight VLANs, e.g. the first octet corresponding to VLANs with VlanIndex values of 0 through 7, the second octet to VLANs 8 through 15, etc. Within each octet, the most significant bit represents the lowest numbered VLAN, and the least significant bit represents the highest numbered VLAN, thus each vlan is represented by a single bit within the octet. The bits in this object will be set to '1' if the corresponding Vlans are in the out-going interface (vlan) list of the IP multicast flow described by this row instance." ::= { cseFlowMcastResultEntry 11 } cseFlowMcastResultDstVlans2k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN, with VlanIndex values of 1024 through 2047,with each octet within the value of this object specifies a set of eight VLANs, e.g. the first octet corresponding to VLANs with VlanIndex values of 1024 through 1031, the second octet to VLANs 1032 through 1039 etc. Within each octet, the most significant bit represents the lowest numbered VLAN, and the least significant bit represents the highest numbered VLAN, thus each vlan is represented by a single bit within the octet. The bits in this object will be set to '1' if the corresponding Vlans are in the out-going interface (vlan) list of the IP multicast flow described by this row instance." ::= { cseFlowMcastResultEntry 12 } cseFlowMcastResultDstVlans3k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN. With VlanIndex values of 2048 through 3071 with each octet within the value of this object specifies a set of eight VLANs, e.g. the first octet corresponding to VLANs with VlanIndex values of 2048 through 2055, the second octet to VLANs 2056 through 2063 etc. Within each octet, the most significant bit represents the lowest numbered VLAN, and the least significant bit represents the highest numbered VLAN, thus each vlan is represented by a single bit within the octet. The bits in this object will be set to '1' if the corresponding Vlans are in the out-going interface (vlan) list of the IP multicast flow described by this row instance." ::= { cseFlowMcastResultEntry 13 } cseFlowMcastResultDstVlans4k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN. With VlanIndex values of 3072 through 4095, with each octet within the value of this object specifies a set of eight VLANs, e.g. the first octet corresponding to VLANs with VlanIndex values of 3072 through 3079 the second octet to VLANs 3080 through 3087 etc. Within each octet, the most significant bit represents the lowest numbered VLAN, and the least significant bit represents the highest numbered VLAN, thus each vlan is represented by a single bit within the octet. The bits in this object will be set to '1' if the corresponding Vlans are in the out-going interface (vlan) list of the IP multicast flow described by this row instance." ::= { cseFlowMcastResultEntry 14 } cseFlowMcastResultMvrf OBJECT-TYPE SYNTAX MplsVpnId MAX-ACCESS read-only STATUS current DESCRIPTION "The MVRF to which this flow belongs to." ::= { cseFlowMcastResultEntry 15 } cseFlowMcastResultAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The Internet address type of cseFlowMcastResultGroup and cseFlowMcastResultSource." ::= { cseFlowMcastResultEntry 16 } cseFlowMcastResultGroup OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The multicast group IP address of the multicast layer 3 flow." ::= { cseFlowMcastResultEntry 17 } cseFlowMcastResultSource OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The source address of the multicast layer 3 flow." ::= { cseFlowMcastResultEntry 18 } cseFlowMcastResultFlowType OBJECT-TYPE SYNTAX INTEGER { other(1), rpfMfd(2), partialSC(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the type of multicast layer 3 flow. other - Multicast flow type is none of the followoing. rpfMfd - This flow is a RPF MFD flow. partial - This flow is a partial shortcut flow." ::= { cseFlowMcastResultEntry 19 } cseFlowMcastResultHFlag1k2k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..256)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per out-going interface (VLAN) with VlanIndex values of 0 through 2047. Each octet within the value of this object specifies a set of eight VLANs, e.g. the first octet corresponding to VLANs with VlanIndex values of 0 through 7, the second octet to VLANs 8 through 15, etc. Within each octet, the most significant bit represents the lowest numbered VLAN, and the least significant bit represents the highest numbered VLAN, thus each vlan is represented by a single bit within the octet. The bits in this object will be set to '1' if the multicast layer 3 flow described by this row instance is hardware switched on the corresponding VLAN. If the length of this string is less than 256 octets, any 'missing' octets are assumed to contain the value of zero." ::= { cseFlowMcastResultEntry 20 } cseFlowMcastResultHFlag3k4k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..256)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per out-going interface (VLAN) with VlanIndex values of 2048 through 4095. Each octet within the value of this object specifies a set of eight VLANs, e.g. the first octet corresponding to VLANs with VlanIndex values of 2048 through 2055, the second octet to VLANs 2056 through 2063 etc. Within each octet, the most significant bit represents the lowest numbered VLAN, and the least significant bit represents the highest numbered VLAN, thus each vlan is represented by a single bit within the octet. The bits in this object will be set to '1' if the multicast layer 3 flow described by this row instance is hardware switched on the corresponding VLAN. If the length of this string is less than 256 octets, any 'missing' octets are assumed to contain the value of zero." ::= { cseFlowMcastResultEntry 21 } -- Multicast MLS-SE global configuration cseFlowMcastSwitchStatus OBJECT-TYPE SYNTAX ControlStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The current status of the global IP multicast flow switching capability. When enabled, the switch engine will be able to install multicast flow entries in its L3 forwarding table, and perform hardware assisted switching for the flows." ::= { cseFlow 14 } -- Now that our hardware can L3 switch IPX traffic cseFlowIPXEstablishedAgingTime OBJECT-TYPE SYNTAX Integer32 (1..2147483647) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The administrative aging time for established IPX flows. The default value for this object is implementation specific. The corresponding operational object is cseFlowOperIPXAgingTime." ::= { cseFlow 15 } cseStaticIpxExtRouterTable OBJECT-TYPE SYNTAX SEQUENCE OF CseStaticIpxExtRouterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of external routers which are enabled for Layer 3 IPX switching by the switching engine. This table may contain routers that have not yet been discovered by the device." ::= { cseFlow 16 } cseStaticIpxExtRouterEntry OBJECT-TYPE SYNTAX CseStaticIpxExtRouterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the cseStaticIpxExtRouterTable for enabling an external router to be installed in the switch's router table. The entry is created and deleted by using cseStaticIpxRouterStatus." INDEX { cseRouterIndex } ::= { cseStaticIpxExtRouterTable 1 } CseStaticIpxExtRouterEntry ::= SEQUENCE { cseStaticIpxRouterName DisplayString, cseStaticIpxRouterOwner OwnerString, cseStaticIpxRouterStatus RowStatus } cseStaticIpxRouterName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "DNS name (if available) of the external router." ::= { cseStaticIpxExtRouterEntry 1 } cseStaticIpxRouterOwner OBJECT-TYPE SYNTAX OwnerString MAX-ACCESS read-create STATUS current DESCRIPTION "String indicating the owner who created the static entry." ::= { cseStaticIpxExtRouterEntry 2 } cseStaticIpxRouterStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Used to manage creation and deletion of rows in this table. Once a row becomes active, values within that row cannot be modified except by deleting and creating the row." ::= { cseStaticIpxExtRouterEntry 3 } cseFlowOperEstablishedAgingTime OBJECT-TYPE SYNTAX Integer32 (1..2147483647) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The operational aging time for IP established flows." ::= { cseFlow 17 } cseFlowOperFastAgingTime OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The operational fast aging time for the established flow entries, that have less number of packets than the value set in the cseFlowOperFastAgePktThreshold,switched within this time." ::= { cseFlow 18 } cseFlowOperFastAgePktThreshold OBJECT-TYPE SYNTAX Unsigned32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The operational packet threshold for the cseFlowOperFastAgingTime." ::= { cseFlow 19 } cseFlowOperIPXAgingTime OBJECT-TYPE SYNTAX Integer32 (1..2147483647) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The operational aging time for established IPX flows." ::= { cseFlow 20 } -- The bridged flow statistics control table cseBridgedFlowStatsCtrlTable OBJECT-TYPE SYNTAX SEQUENCE OF CseBridgedFlowStatsCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table controls the reporting of intra-vlan statistics for bridged flow per vlan. When a vlan is created in a device supporting this table, a corresponding entry of this table will be added." ::= { cseFlow 21 } cseBridgedFlowStatsCtrlEntry OBJECT-TYPE SYNTAX CseBridgedFlowStatsCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row instance contains the configuration to enable or disable the reporting of intra-vlan statistics for bridged flow per vlan." INDEX { cseBridgedFlowVlan } ::= { cseBridgedFlowStatsCtrlTable 1 } CseBridgedFlowStatsCtrlEntry ::= SEQUENCE { cseBridgedFlowVlan VlanIndex, cseFlowBridgedFlowStatsEnable TruthValue } cseBridgedFlowVlan OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Indicates the Vlan number on which the reporting of intra-vlan bridged flow statistics is configured." ::= { cseBridgedFlowStatsCtrlEntry 1 } cseFlowBridgedFlowStatsEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether intra-vlan bridged flow statistics is enabled. If this object is set to 'true', intra-vlan bridged flow statistics is reported in cseFlowDataTable when a corresponding query is set up in cseFlowQueryTable. If this object is set to 'false', intra-vlan bridged flow statistics is not reported. The default is false." DEFVAL { false } ::= { cseBridgedFlowStatsCtrlEntry 2 } cseFlowIPFlowMask OBJECT-TYPE SYNTAX INTEGER { dstOnly(1), srcDst(2), fullFlow(3), srcOnly(4), intDstSrc(5), intFull(6), null(7), intDstOnly(8), intSrcOnly(9) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates the flow mask for IP flows. If dstOnly(1) is used, it enables flows based on Layer 3 destination addresses only. If srcDst(2) is used, it enables flows based on both Layer 3 source and destination addresses only. If fullFlow(3) is used, it enables flows based on Layer 4 port numbers in addition to source and destination addresses. If srcOnly(4) is used, it enables flows based on Layer 3 source addresses only. If intDstSrc(5) is used, it enables flows based on source interface in addition to source and destination addresses. If intFull(6) is used, it enables flows based on source interface in addition to Layer 4 port numbers, source and destination addresses. If null(7) is used, no flow will be enabled. If intDstOnly(8) is used, it enables flows based on source interface in addition to the destination addresses. If intSrcOnly(9) is used, it enables flows based on source interface in addition to the source addresses." ::= { cseFlow 22 } cseFlowIPXFlowMask OBJECT-TYPE SYNTAX INTEGER { dstOnly(1), srcDst(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the flow mask for IPX flows. If dstOnly(1) is used, it enables flows based on Layer 3 destination addresses only. If srcDst(2) is used, it enables flows based on both Layer 3 source and destination addresses only." ::= { cseFlow 23 } cseFlowLongAgingTime OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The administrative long aging time for the established flow entries. Setting to value of 0 turns off long aging." ::= { cseFlow 24 } -- The protocol exclude table cseFlowExcludeTable OBJECT-TYPE SYNTAX SEQUENCE OF CseFlowExcludeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table controls the flow creation based on protocol and port number. If a packet matches the protocol and port number specified in this table entries, a flow entry will not be established." ::= { cseFlow 25 } cseFlowExcludeEntry OBJECT-TYPE SYNTAX CseFlowExcludeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row instance contains the configuration to enable or disable the establishment of flow entry for matching traffic." INDEX { cseFlowExcludePort } ::= { cseFlowExcludeTable 1 } CseFlowExcludeEntry ::= SEQUENCE { cseFlowExcludePort CiscoPort, cseFlowExcludeProtocol INTEGER, cseFlowExcludeStatus RowStatus } cseFlowExcludePort OBJECT-TYPE SYNTAX CiscoPort MAX-ACCESS not-accessible STATUS current DESCRIPTION "Indicates the TCP or UDP port number that matching traffic will be excluded from flow establishment. The value of 0 is not allowed." ::= { cseFlowExcludeEntry 1 } cseFlowExcludeProtocol OBJECT-TYPE SYNTAX INTEGER { udp(1), tcp(2), both(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the protocol that matching traffic will be excluded from flow establishment." ::= { cseFlowExcludeEntry 2 } cseFlowExcludeStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. New rows are created using 'createAndGo' and deleted using 'destroy'. Once 'active' this object may be set to only 'destroy'. cseFlowExcludeProtocol may be modified at any time (even while the row is active)." ::= { cseFlowExcludeEntry 3 } -- The flow statistics table cseFlowStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF CseFlowStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing flow statistics information on each switching engine." ::= { cseFlow 26 } cseFlowStatsEntry OBJECT-TYPE SYNTAX CseFlowStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of cseFlowStatsTable, containing flow statistics maintained by a switching engine entity (identified by entPhysicalIndex). Each switching engine managed by this MIB module has an entry in this table." INDEX { entPhysicalIndex } ::= { cseFlowStatsTable 1 } CseFlowStatsEntry ::= SEQUENCE { cseFlowTotalFlows Gauge32, cseFlowTotalIpv4Flows Gauge32 } cseFlowTotalFlows OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of flow entries installed in this switching engine." ::= { cseFlowStatsEntry 1 } cseFlowTotalIpv4Flows OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of IPv4 flow entries in this switching engine." ::= { cseFlowStatsEntry 2 } -- Optional NetFlow Lan Switching group cseNetflowLSExportStatus OBJECT-TYPE SYNTAX ControlStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Status of the Netflow LAN Switching data export feature." ::= { cseNetflowLS 1 } cseNetflowLSExportHost OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Network(IP) address in dotted decimal format or the DNS hostname of the host to which Netflow LAN switching statistics are exported. This object is deprecated and replaced by cndeCollectorAddress in CISCO-NDE-MIB." ::= { cseNetflowLS 2 } cseNetflowLSExportTransportNumber OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The transport(UDP) port number to be used for the Netflow LAN switching statistics being exported. This object is deprecated and replaced by cndeCollectorPort in CISCO-NDE-MIB." ::= { cseNetflowLS 3 } cseNetflowLSExportDataSource OBJECT-TYPE SYNTAX FlowAddressComponent MAX-ACCESS read-write STATUS current DESCRIPTION "The source network address used as a filter for selecting the flows to which the netflow LAN switching data export feature is applied." ::= { cseNetflowLS 4 } cseNetflowLSExportDataSourceMask OBJECT-TYPE SYNTAX FlowAddressComponent MAX-ACCESS read-write STATUS current DESCRIPTION "The mask to be applied to the corresponding instance of cseNetflowExportDataSource." ::= { cseNetflowLS 5 } cseNetflowLSExportDataDest OBJECT-TYPE SYNTAX FlowAddressComponent MAX-ACCESS read-write STATUS current DESCRIPTION "The destination network address used as a filter for selecting the flows to which the netflow LAN switching data export feature is applied." ::= { cseNetflowLS 6 } cseNetflowLSExportDataDestMask OBJECT-TYPE SYNTAX FlowAddressComponent MAX-ACCESS read-write STATUS current DESCRIPTION "The mask to be applied to its corresponding instance of cseNetflowExportDataDest." ::= { cseNetflowLS 7 } cseNetflowLSExportDataProtocol OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "The protocol used as a filter for selecting the flows to which the netflow LAN switching data export feature is applied." REFERENCE "The protocol value is defined in the RFC 1700." ::= { cseNetflowLS 8 } cseNetflowLSExportDataFilterSelection OBJECT-TYPE SYNTAX INTEGER { included(1), excluded(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The filter set can be chosen either included(1) or excluded(2) mutually exclusive. If this object is set to included(1) - exports the flows that match cseNetflowLSExportDataSource, cseNetflowLSExportDataSourceMask, cseNetflowLSExportDataDest, cseNetflowLSExportDataDestMask and cseNetflowLSExportDataProtocol. excluded(2) - exports the flows that don't match cseNetflowLSExportDataSource, cseNetflowLSExportDataSourceMask, cseNetflowLSExportDataDest, cseNetflowLSExportDataDestMask and cseNetflowLSExportDataProtocol." ::= { cseNetflowLS 9 } cseNetflowLSExportNDEVersionNumber OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The netflow data export version number which is supported by the device. The typical value of this object can be 1, 7 or 8." ::= { cseNetflowLS 10 } cseNetflowLSFilterSupport OBJECT-TYPE SYNTAX INTEGER { single(1), multiple(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether this device supports single filter or multiple filters. single - use objects in cseNDESingleFilterGroupRev1 to configure NDE filtering paramaters. multiple - use objects in cseNDEMultipleFiltersGroup to configure NDE filtering paramaters." ::= { cseNetflowLS 11 } cseNetflowLSFilterTable OBJECT-TYPE SYNTAX SEQUENCE OF CseNetflowLSFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A Table containing Netflow Data Export filtering configuration." ::= { cseNetflowLS 12 } cseNetflowLSFilterEntry OBJECT-TYPE SYNTAX CseNetflowLSFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptutal row in the cseNetflowLSFilterTable, representing a NDE filter configuration." INDEX { cseNetflowLSFilterIndex } ::= { cseNetflowLSFilterTable 1 } CseNetflowLSFilterEntry ::= SEQUENCE { cseNetflowLSFilterIndex Unsigned32, cseNetflowLSFilterDataSource FlowAddressComponent, cseNetflowLSFilterDataSourceMask FlowAddressComponent, cseNetflowLSFilterDataDest FlowAddressComponent, cseNetflowLSFilterDataDestMask FlowAddressComponent, cseNetflowLSFilterDataProtocol Integer32, cseNetflowLSFilterSelection INTEGER, cseNetflowLSFilterStatus RowStatus } cseNetflowLSFilterIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer which uniquely identifies the filter" ::= { cseNetflowLSFilterEntry 1 } cseNetflowLSFilterDataSource OBJECT-TYPE SYNTAX FlowAddressComponent MAX-ACCESS read-create STATUS current DESCRIPTION "The source network address used as a filter for selecting the flows to which the netflow LAN switching data export feature is applied. If cseNetflowLSNDEFilterDataSource contains all zeros, then the cseNetflowLSNDEFilterDataSource object will not be included in the filtering criterion." DEFVAL { '000000000000'H } ::= { cseNetflowLSFilterEntry 2 } cseNetflowLSFilterDataSourceMask OBJECT-TYPE SYNTAX FlowAddressComponent MAX-ACCESS read-create STATUS current DESCRIPTION "The mask to be applied to the corresponding instance of cseNetflowExportDataSource. If cseNetflowLSFilterDataSourceMask contains all zeros, then the cseNetflowLSFilterDataSourceMask object will not be included in the filtering criterion." DEFVAL { '000000000000'H } ::= { cseNetflowLSFilterEntry 3 } cseNetflowLSFilterDataDest OBJECT-TYPE SYNTAX FlowAddressComponent MAX-ACCESS read-create STATUS current DESCRIPTION "The destination network address used as a filter for selecting the flows to which the netflow LAN switching data export feature is applied. If cseNetflowLSFilterDataDest contains all zeros, then the cseNetflowLSFilterDataDest object will not be included in the filtering criterion." DEFVAL { '000000000000'H } ::= { cseNetflowLSFilterEntry 4 } cseNetflowLSFilterDataDestMask OBJECT-TYPE SYNTAX FlowAddressComponent MAX-ACCESS read-create STATUS current DESCRIPTION "The mask to be applied to its corresponding instance of cseNetflowExportDataDest. If cseNetflowLSFilterDataDestMask contains all zeros, then the cseNetflowLSFilterDataDestMask object will not be included in the filtering criterion." DEFVAL { '000000000000'H } ::= { cseNetflowLSFilterEntry 5 } cseNetflowLSFilterDataProtocol OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The protocol used as a filter for selecting the flows to which the netflow LAN switching data export feature is applied. The default value is set to 0, to specify that no value has been set. If cseNetflowLSFilterDataProtocol is set to 0, then the cseNetflowLSFilterDataProtocol object will not be included in the filtering criterion." DEFVAL { 0 } ::= { cseNetflowLSFilterEntry 6 } cseNetflowLSFilterSelection OBJECT-TYPE SYNTAX INTEGER { included(1), excluded(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The filter set can be chosen either included(1) or excluded(2). If this object is set to included(1) - exports the flows that match cseNetflowLSFilterDataSource, cseNetflowLSFilterDataSourceMask, cseNetflowLSFilterDataDest, cseNetflowLSFilterDataDestMask and cseNetflowLSFilterDataProtocol. excluded(2) - exports the flows that don't match cseNetflowLSFilterDataSource, cseNetflowLSFilterDataSourceMask, cseNetflowLSFilterDataDest, cseNetflowLSFilterDataDestMask and cseNetflowLSFilterDataProtocol." ::= { cseNetflowLSFilterEntry 7 } cseNetflowLSFilterStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status object used to manage the rows in this table. Once a row becomes active, values within that row cannot be modified except by deleting and creating the row." ::= { cseNetflowLSFilterEntry 8 } cseNetFlowIfIndexEnable OBJECT-TYPE SYNTAX BITS { destIfIndex(0), srcIfIndex(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether ifIndex reporting in NDE (Netflow Data Export) is enabled. if bit destIfIndex(0) is on, destination ifIndex reporting in NDE is enabled. if bit srcIfIndex(1) is on, source ifIndex reporting in NDE is enabled." ::= { cseNetflowLS 13 } cseNetflowASInfoExportCtrl OBJECT-TYPE SYNTAX INTEGER { disable(1), originate(2), peer(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether export of Autonomous System(AS) number information, in the NDE records, is enabled. disable - Disables the export of AS number information. originate - Enables the export of origination AS numbers of source and destination IP addresses. peer - Enables the export of peer AS numbers of source and destination IP addresses." ::= { cseNetflowLS 14 } cseNetflowPerVlanIfGlobalEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether 'creation of Netflow entries per VLAN interface' feature is enabled at the device level. If this object is set to 'false', netflow entries will be created for all VLANs. If this object is set to 'true', creation of netflow entries can be controlled by cseNetflowPerVlanIfCtrlTable." ::= { cseNetflowLS 15 } cseNetflowPerVlanIfCtrlTable OBJECT-TYPE SYNTAX SEQUENCE OF CseNetflowPerVlanIfCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control netflow entry creation for each VLAN. When a VLAN is created, a corresponding entry is added to this table." ::= { cseNetflowLS 16 } cseNetflowPerVlanIfCtrlEntry OBJECT-TYPE SYNTAX CseNetflowPerVlanIfCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing the configuration to enable or disable netflow entry creation for each VLAN." INDEX { cseNetflowPerVlanIfCtrlVlan } ::= { cseNetflowPerVlanIfCtrlTable 1 } CseNetflowPerVlanIfCtrlEntry ::= SEQUENCE { cseNetflowPerVlanIfCtrlVlan VlanIndex, cseNetflowPerVlanIfEnable TruthValue } cseNetflowPerVlanIfCtrlVlan OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Indicates the VLAN number on which creation of netflow entries is configured." ::= { cseNetflowPerVlanIfCtrlEntry 1 } cseNetflowPerVlanIfEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies whether creation of netflow entries is enabled on this VLAN. If this object is set to 'true', the system will create netflow entries for this VLAN. If this object is set to 'false', the system will not create any netflow entries for this VLAN. When the value of cseNetflowPerVlanIfGlobalEnable is 'false', this object will not take effect." ::= { cseNetflowPerVlanIfCtrlEntry 2 } -- L3 switching statistics cseL3StatsTable OBJECT-TYPE SYNTAX SEQUENCE OF CseL3StatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing L3 statistics information on each switching engine." ::= { cseL3Objects 1 } cseL3StatsEntry OBJECT-TYPE SYNTAX CseL3StatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of cseL3StatsTable, containing L3 statistics maintained by a switching engine entity (identified by entPhysicalIndex). Each switching engine managed by this MIB module has an entry in this table." INDEX { entPhysicalIndex } ::= { cseL3StatsTable 1 } CseL3StatsEntry ::= SEQUENCE { cseL3SwitchedTotalPkts Counter32, cseL3SwitchedTotalOctets Counter64, cseL3CandidateFlowHits Counter32, cseL3EstablishedFlowHits Counter32, cseL3ActiveFlows Gauge32, cseL3FlowLearnFailures Counter32, cseL3IntFlowInvalids Counter32, cseL3ExtFlowInvalids Counter32, cseL3SwitchedPktsPerSec Counter32 } cseL3SwitchedTotalPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of packets switched at Layer 3 by this switching engine." ::= { cseL3StatsEntry 1 } cseL3SwitchedTotalOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of octets in the total packets switched at Layer 3 by this switching engine." ::= { cseL3StatsEntry 2 } cseL3CandidateFlowHits OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of L3 Cache hits for the candidate flow entries in this switching engine." ::= { cseL3StatsEntry 3 } cseL3EstablishedFlowHits OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of L3 Cache hits for established flow entries in this switching engine." ::= { cseL3StatsEntry 4 } cseL3ActiveFlows OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of active flows in the Layer 3 flow table of this switching engine." ::= { cseL3StatsEntry 5 } cseL3FlowLearnFailures OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of flows that failed to be learned because the Layer 3 flow table in this switching engine was full." ::= { cseL3StatsEntry 6 } cseL3IntFlowInvalids OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of flow invalidation events received by this switching engine from the internal router(s)." ::= { cseL3StatsEntry 7 } cseL3ExtFlowInvalids OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of flow invalidation events received by this switching engine from external routers." ::= { cseL3StatsEntry 8 } cseL3SwitchedPktsPerSec OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets switched per second at Layer 3 by this switching engine." ::= { cseL3StatsEntry 9 } -- Per-VLAN L3 statistics cseL3VlanStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF CseL3VlanStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing per-VLAN, Layer 3 statistics information per switching engine." ::= { cseL3Objects 2 } cseL3VlanStatsEntry OBJECT-TYPE SYNTAX CseL3VlanStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of cseL3VlanStatsTable, containing per-VLAN Layer 3 statistics maintained by a switching engine (identified by entPhysicalIndex). An entry exists for each known VLAN for each switching engine." INDEX { entPhysicalIndex, cseL3VlanIndex } ::= { cseL3VlanStatsTable 1 } CseL3VlanStatsEntry ::= SEQUENCE { cseL3VlanIndex VlanIndex, cseL3VlanInPkts Counter64, cseL3VlanInOctets Counter64, cseL3VlanOutPkts Counter64, cseL3VlanOutOctets Counter64, cseL3VlanInUnicastPkts Counter64, cseL3VlanInUnicastOctets Counter64, cseL3VlanOutUnicastPkts Counter64, cseL3VlanOutUnicastOctets Counter64 } cseL3VlanIndex OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Vlan number for which the statistics are maintained by this entry." ::= { cseL3VlanStatsEntry 1 } cseL3VlanInPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets Layer 3 forwarded from this Vlan to some other VLAN by this switching engine." ::= { cseL3VlanStatsEntry 2 } cseL3VlanInOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of octets in packets Layer-3 forwarded from this Vlan to some other VLAN by this switching engine." ::= { cseL3VlanStatsEntry 3 } cseL3VlanOutPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets Layer-3 forwarded to this Vlan by this switching engine." ::= { cseL3VlanStatsEntry 4 } cseL3VlanOutOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of octets in packets Layer-3 forwarded to this Vlan by this switching engine." ::= { cseL3VlanStatsEntry 5 } cseL3VlanInUnicastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of unicast packets Layer 3 forwarded from this Vlan to some other VLAN by this switching engine." ::= { cseL3VlanStatsEntry 6 } cseL3VlanInUnicastOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of octets in unicast packets Layer-3 forwarded from this Vlan to some other VLAN by this switching engine." ::= { cseL3VlanStatsEntry 7 } cseL3VlanOutUnicastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of unicast packets Layer 3 forwarded to this Vlan by this switching engine." ::= { cseL3VlanStatsEntry 8 } cseL3VlanOutUnicastOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of octets in unicast packets Layer-3 forwarded to this Vlan by this switching engine." ::= { cseL3VlanStatsEntry 9 } -- Switch Engine based layer 3 flow statistics; it is protocol -- independent, i.e. IP and IPX statistics are not separated -- This group is an augmentation of cseL3StatsTable cseStatsFlowTable OBJECT-TYPE SYNTAX SEQUENCE OF CseStatsFlowEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of flow statistics per switch engine that is not covered in cseL3StatsTable." ::= { cseL3Objects 3 } cseStatsFlowEntry OBJECT-TYPE SYNTAX CseStatsFlowEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row about slot based L3 flow statistics." AUGMENTS { cseL3StatsEntry } ::= { cseStatsFlowTable 1 } CseStatsFlowEntry ::= SEQUENCE { cseStatsFlowAged Counter32, cseStatsFlowPurged Counter32, cseStatsFlowParityFail Counter32 } cseStatsFlowAged OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of layer 3 flows aged out by hardware. Management applications can control flow aging by setting the value of cseFlowEstablishedAgingTime object." ::= { cseStatsFlowEntry 1 } cseStatsFlowPurged OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of layer 3 flows purged by software; it may happen because a router invalidates certain flows, or a router for which flows are being switched has been excluded from cseRouterTable, or access-list has changed, or certain features have been enabled that would purge certain flows (TCP interception, Web cache are examples of such features)." ::= { cseStatsFlowEntry 2 } cseStatsFlowParityFail OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of memory parity errors on accessing flows in the cache pools. It may be due to the internal RAM reading error, not necessarily the corrupted flow data." ::= { cseStatsFlowEntry 3 } -- Utilization level of flow cache pool per Switch Engine -- Flows are combined for IP and IPX cseCacheUtilTable OBJECT-TYPE SYNTAX SEQUENCE OF CseCacheUtilEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of utilization levels in percentage of cache capacity per switch engine. Each row instance is the current flow utilization information in the cache pool of the corresponding switching engine." ::= { cseL3Objects 4 } cseCacheUtilEntry OBJECT-TYPE SYNTAX CseCacheUtilEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row instance represents layer 3 flow utilization of a particular cache pool on a switching engine." INDEX { entPhysicalIndex } ::= { cseCacheUtilTable 1 } CseCacheUtilEntry ::= SEQUENCE { cseCacheUtilization Gauge32, cseCacheEntriesCreated Unsigned32, cseCacheEntriesFailed Unsigned32 } cseCacheUtilization OBJECT-TYPE SYNTAX Gauge32 (0..100) MAX-ACCESS read-only STATUS current DESCRIPTION "Flow utilization level in percentage in this switching engine. It includes the flow entries for both unicast and multicast. The lighter the utilization level, the less risk of dropping flows, i.e. the higher success-rate of flow insertion." ::= { cseCacheUtilEntry 1 } cseCacheEntriesCreated OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the total number of flow entries successfully created in this switching engine." ::= { cseCacheUtilEntry 2 } cseCacheEntriesFailed OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of flow entries which were failed to be created in this switching engine." ::= { cseCacheUtilEntry 3 } -- L3 error counters table. cseErrorStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF CseErrorStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of IP and IPX error counters per switch engine." ::= { cseL3Objects 5 } cseErrorStatsEntry OBJECT-TYPE SYNTAX CseErrorStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row instance represents layer-3 IP and IPX error counters on a switching engine." INDEX { entPhysicalIndex } ::= { cseErrorStatsTable 1 } CseErrorStatsEntry ::= SEQUENCE { cseIpPlenErrors Counter64, cseIpTooShortErrors Counter64, cseIpCheckSumErrors Counter64, cseIpxPlenErrors Counter64, cseIpxTooShortErrors Counter64 } cseIpPlenErrors OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the number of IP length against physical length errors." ::= { cseErrorStatsEntry 1 } cseIpTooShortErrors OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the number of IP length too short errors." ::= { cseErrorStatsEntry 2 } cseIpCheckSumErrors OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the number of IP checksum errors." ::= { cseErrorStatsEntry 3 } cseIpxPlenErrors OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the number of IPX length against physical length errors." ::= { cseErrorStatsEntry 4 } cseIpxTooShortErrors OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the number of IPX length too short errors." ::= { cseErrorStatsEntry 5 } -- L3 error counters table. cseErrorStatsLCTable OBJECT-TYPE SYNTAX SEQUENCE OF CseErrorStatsLCEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of IP and IPX error counters per switch engine." ::= { cseL3Objects 6 } cseErrorStatsLCEntry OBJECT-TYPE SYNTAX CseErrorStatsLCEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row instance represents layer-3 IP and IPX error counters on a switching engine." INDEX { entPhysicalIndex } ::= { cseErrorStatsLCTable 1 } CseErrorStatsLCEntry ::= SEQUENCE { cseLCIpPlenErrors Counter32, cseLCIpTooShortErrors Counter32, cseLCIpCheckSumErrors Counter32, cseLCIpxPlenErrors Counter32, cseLCIpxTooShortErrors Counter32 } cseLCIpPlenErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the number of IP length against physical length errors." ::= { cseErrorStatsLCEntry 1 } cseLCIpTooShortErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the number of IP length too short errors." ::= { cseErrorStatsLCEntry 2 } cseLCIpCheckSumErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the number of IP checksum errors." ::= { cseErrorStatsLCEntry 3 } cseLCIpxPlenErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the number of IPX length against physical length errors." ::= { cseErrorStatsLCEntry 4 } cseLCIpxTooShortErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the number of IPX length too short errors." ::= { cseErrorStatsLCEntry 5 } -- Packets Switched Per Second cseL3SwitchedAggrPktsPerSec OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets switched per second at Layer 3 by the entire system." ::= { cseL3Objects 7 } -- Protocol Filter capability cseProtocolFilterEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates if protocol filtering is enabled in the device." ::= { cseProtocolFilter 1 } cseProtocolFilterPortTable OBJECT-TYPE SYNTAX SEQUENCE OF CseProtocolFilterPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing the protocol filtering configuration and status information on ports." ::= { cseProtocolFilter 2 } cseProtocolFilterPortEntry OBJECT-TYPE SYNTAX CseProtocolFilterPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the cseProtocolFilterPortTable, representing a Protocol filter configuration status information for a particular port (identified by ifIndex) and protocol type." INDEX { ifIndex, cseProtocolFilterPortProtocol } ::= { cseProtocolFilterPortTable 1 } CseProtocolFilterPortEntry ::= SEQUENCE { cseProtocolFilterPortProtocol INTEGER, cseProtocolFilterPortAdminStatus INTEGER, cseProtocolFilterPortOperStatus INTEGER } cseProtocolFilterPortProtocol OBJECT-TYPE SYNTAX INTEGER { ip(1), ipx(2), grpProtocols(3) -- Appletalk/Decnet/Vines } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The protocol (group) to filter, used here as the secondary index." ::= { cseProtocolFilterPortEntry 1 } cseProtocolFilterPortAdminStatus OBJECT-TYPE SYNTAX INTEGER { on(1), off(2), auto(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "An indication of the administrative status of the protocol filtering on this interface. - on(1) indicates that the interface will send and receive the traffic for protocol specified in cseProtocolFilterPortProtocol. - off(2) indicates that the interface will not receive traffic for this protocol, or if this feature is not supported. - auto(3) indicates that the corresponding cseProtocolFilterPortOperStatus will transit to 'on' after receiving one packet of this protocol type." ::= { cseProtocolFilterPortEntry 2 } cseProtocolFilterPortOperStatus OBJECT-TYPE SYNTAX INTEGER { on(1), off(2), notSupported(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "An indication of the operational status of filtering for this protocol on this interface. - on(1) indicates that the interface will send and receive the protocol traffic. - off(2) indicates that the interface will drop all traffic belonging to this protocol. - notSupported(3) indicates the hardware does not support protocol filtering." ::= { cseProtocolFilterPortEntry 3 } -- This MIB group/table is designed for control of purging flow caches -- The caches are distributed in the switching engines across the system cseUcastCacheTable OBJECT-TYPE SYNTAX SEQUENCE OF CseUcastCacheEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A control table used to purge certain types of IP/IPX layer 3 unicast flows stored in the cache pool." ::= { cseUcastCache 1 } cseUcastCacheEntry OBJECT-TYPE SYNTAX CseUcastCacheEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the cseUcastCacheTable, used to set up flow clearing criteria. The actual purging is started by setting the value of cseUcastCacheStatus to 'active'. Once a row becomes active, values within the row cannot be modified, except by setting it to 'notInService' first or deleting and re-creating the row." INDEX { cseUcastCacheIndex } ::= { cseUcastCacheTable 1 } CseUcastCacheEntry ::= SEQUENCE { cseUcastCacheIndex Unsigned32, cseUcastCacheFlowType INTEGER, cseUcastCacheTransport INTEGER, cseUcastCacheDest FlowAddressComponent, cseUcastCacheDestMask FlowAddressComponent, cseUcastCacheSource FlowAddressComponent, cseUcastCacheSrcMask FlowAddressComponent, cseUcastCacheRtrIp IpAddress, cseUcastCacheOwner OwnerString, cseUcastCacheResult INTEGER, cseUcastCacheStatus RowStatus } cseUcastCacheIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer which uniquely identifies the flow purge contained in this row instance." ::= { cseUcastCacheEntry 1 } cseUcastCacheFlowType OBJECT-TYPE SYNTAX INTEGER { any(1), dstOnly(2), srcOrDst(3), srcAndDst(4), fullFlow(5), ipxDstOnly(6), ipxSrcAndDst(7) } MAX-ACCESS read-create STATUS current DESCRIPTION "Setting each value causes the appropriate action: 'dstOnly' - causes purge of flows in the cache whose absolute destination IP addresses match the address part of the value set in the cseUcastCacheDest object. If cseUcastCacheDestMask is also specified at the same time, it will be applied to the address part of cseUcastCacheDest. 'srcOrDst' - causes purge of flows in the cache whose either absolute source or destination IP addresses match the address parts of the values set in cseUcastCacheSource or cseUcastCacheDest. If cseUcastCacheDestMask/cseUcastCacheSrcMask also specified, they will be applied to the address parts of cseUcastCacheSource/ cseUcastCacheDest appropriately. 'srcAndDst' - causes purge of flows in the cache whose both absolute source and destination IP addresses match the address parts of values set in cseUcastCacheSource and cseUcastCacheDest objects. If cseUcastCacheSrcMask and cseUcastCacheDestMask also specified, they will be applied to the address parts of cseUcastCacheSource and cseUcastCacheDest. 'fullFlow' - causes purge of IP flows whose IP addresses and transport port numbers match the values set in cseUcastCacheDest and cseUcastCacheSource objects. If either cseUcastCacheDestMask or cseUcastCacheSrcMask objects have valid values, they will be applied to the respective address parts of cseUcastCacheDest and cseUcastCacheSource objects. This option is typically used to purge flows relevant to specific applications such as FTP, WWW, TELNET, etc. 'ipxDstOnly' - causes purge of IPX flows in the cache whose absolute destination IPX address match the address part of the value set in cseUcastCacheDest object. if cseUcastCacheDestMask holds valid value at the same time, it will be applied to the address part of cseUcastCacheDest. 'ipxSrcAndDst' - causes purge of IPX flows in the cache whose both absolute source and destination IPX addresses match the address parts of the values set in cseUcastCacheSource and cseUcastCacheDest objects. If either of cseUcastCacheSrcMask or cseUcastCacheDestMask have valid values at the same time, they will be applied to the respective address parts of cseUcastCacheSource and cseUcastCacheDest objects. 'any' - causes purge of all established flows currently in the cache. The values of cseUcastCacheDest, cseUcastCacheSource, cseUcastCacheDestMask, cseUcastCacheSrcMask, and cseUcastCacheTransport should be ignored in this case. Note: 1. When the row instance is initialized, the value of this object instance will be set to 'any'. 2. The rest flow parameter variables will not be instantiated until they get set by management applications based on the value of cseUcastCacheFlowType object." DEFVAL { any } ::= { cseUcastCacheEntry 2 } cseUcastCacheTransport OBJECT-TYPE SYNTAX INTEGER { udp(1), tcp(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The IP transport protocol type (if applicable) of the specified switched flows to be purged; it will be instantiated if and only if it gets set by the management applications and the value of cseUcastCacheFlowMask is equal to 'fullFlow'. Its value can not be modified when the corresponding instance of cseUcastCacheStatus is 'active'." ::= { cseUcastCacheEntry 3 } cseUcastCacheDest OBJECT-TYPE SYNTAX FlowAddressComponent MAX-ACCESS read-create STATUS current DESCRIPTION "Destination network address and port number (if applicable). The port field is ignored for IPX flows and IP flows if the value of cseUcastCacheFlowMask is not equal to 'fullFlow'. Its value can not be modified when the corresponding instance of cseUcastCacheStatus is 'active'." ::= { cseUcastCacheEntry 4 } cseUcastCacheDestMask OBJECT-TYPE SYNTAX FlowAddressComponent MAX-ACCESS read-create STATUS current DESCRIPTION "If instantiated, specified and applicable, the destination address mask will be applied to the value of cseUcastCacheDest in the same row instance. Its value can not be modified when the corresponding instance of cseUcastCacheStatus is 'active'." ::= { cseUcastCacheEntry 5 } cseUcastCacheSource OBJECT-TYPE SYNTAX FlowAddressComponent MAX-ACCESS read-create STATUS current DESCRIPTION "Source network address and port number (if applicable). The port field is ignored for IPX flows and IP flows if the value of cseUcastCacheFlowMask is not equal to 'fullFlow'. Its value can not be modified when the corresponding instance of cseUcastCacheStatus is 'active'." ::= { cseUcastCacheEntry 6 } cseUcastCacheSrcMask OBJECT-TYPE SYNTAX FlowAddressComponent MAX-ACCESS read-create STATUS current DESCRIPTION "If instantiated, specified and applicable, the source address mask will be applied to the value of cseUcastCacheSource in the same row instance. Its value can not be modified when the corresponding instance of cseUcastCacheStatus is 'active'." ::= { cseUcastCacheEntry 7 } cseUcastCacheRtrIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "IP address of the router (internal or external) for which the flows are being switched, and need to be purged. An 'all-zero' value is a wildcard IP address for any router. Its value can not be modified when the corresponding instance of cseUcastCacheStatus is 'active'." ::= { cseUcastCacheEntry 8 } cseUcastCacheOwner OBJECT-TYPE SYNTAX OwnerString MAX-ACCESS read-create STATUS current DESCRIPTION "The manager entity that configured this entry and is therefore using the resources assigned to it." ::= { cseUcastCacheEntry 9 } cseUcastCacheResult OBJECT-TYPE SYNTAX INTEGER { purging(1), notPurging(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "state of the flow purging operation. 'purging' - purging operation is proceeding 'notPurging' - the purging operation completed, or not started yet." DEFVAL { notPurging } ::= { cseUcastCacheEntry 11 } cseUcastCacheStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status object used to manage rows in this table. When set to active(1), the flow purge is initiated, and the value of cseUcastCacheResult object becomes 'purging'. However, this object can be set to active(1) only after all the appropriate objects for this query as defined by the value set in the cseUcastCacheFlowType object, have also been set. Upon the completion of flow purge, the value of cseUcastCacheResult object changes to 'notPurging'. Once a row becomes active, values within the row cannot be modified, except by setting it to 'notInService' first, or deleting and re-creating it." ::= { cseUcastCacheEntry 10 } -- This MIB group/table is designed for purging IP multicast -- flows. For a multicast switch, a row instance can be used to clear -- specified multicast L3 flows from its cache pools cseMcastCacheTable OBJECT-TYPE SYNTAX SEQUENCE OF CseMcastCacheEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A control table used to purge specified IP multicast flows from the switch engine." ::= { cseMcastCache 1 } cseMcastCacheEntry OBJECT-TYPE SYNTAX CseMcastCacheEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the cseMcastCacheTable, used to set up flow clearing criteria. The actual purging is started by setting the value of cseMcastCacheStatus to 'active'. Once a row becomes active, values within the row cannot be modified, except by setting it to 'notInService' first, or deleting and re-creating the row." INDEX { cseMcastCacheIndex } ::= { cseMcastCacheTable 1 } CseMcastCacheEntry ::= SEQUENCE { cseMcastCacheIndex Unsigned32, cseMcastCacheFlowType INTEGER, cseMcastCacheGrp McastGroupIp, cseMcastCacheSrc IpAddress, cseMcastCacheRtrIp IpAddress, cseMcastCacheOwner OwnerString, cseMcastCacheResult INTEGER, cseMcastCacheStatus RowStatus } cseMcastCacheIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer which uniquely identifies the flow purge contained in the current row instance." ::= { cseMcastCacheEntry 1 } cseMcastCacheFlowType OBJECT-TYPE SYNTAX INTEGER { any(1), group(2), grpAndSrc(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Setting each value causes the appropriate action: 'any' - causes purge of all established IP multicast layer 3 flows in the cache. The value of cseMcastCacheGrp, and cseMcastCacheSrc will be ignored in this case. 'group' - causes purge of flows whose multicast group IP address match the values of cseMcastCacheGrp. 'grpAndSrc' - causes purge of multicast flows whose both group IP address and source Ip address match the values of cseMcastCacheGrp and cseMcastCacheSrc. Note: 1. The instance of this object is initialized to 'any' when the corresponding row instance is being instantiated. 2. Flow parameter variables, cseMcastCacheGrp, cseMcastCacheSrc, cseMcastCacheRtrIp will not be instantiated until they get set by management applications (in such cases, cseMcastCacheFlowType object should be set to a value other than 'any')." DEFVAL { any } ::= { cseMcastCacheEntry 2 } cseMcastCacheGrp OBJECT-TYPE SYNTAX McastGroupIp MAX-ACCESS read-create STATUS current DESCRIPTION "Specifying multicast group IP address of the flows to be cleared. Its value can not be modified when the corresponding instance of cseMcastCacheStatus is 'active'." ::= { cseMcastCacheEntry 3 } cseMcastCacheSrc OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The source address of the IP multicast flows to be purged. Its value can not be modified when the corresponding instance of cseMcastCacheStatus is 'active'." ::= { cseMcastCacheEntry 4 } cseMcastCacheRtrIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The IP address of the router whose flows are currently being switched, and will be purged. An 'all-zero' value is a wildcard IP address for any router. Its value can not be modified when the corresponding instance of cseMcastCacheStatus is 'active'." ::= { cseMcastCacheEntry 5 } cseMcastCacheOwner OBJECT-TYPE SYNTAX OwnerString MAX-ACCESS read-create STATUS current DESCRIPTION "The manager entity that configured this entry and is therefore using the resources assigned to it." ::= { cseMcastCacheEntry 6 } cseMcastCacheResult OBJECT-TYPE SYNTAX INTEGER { purging(1), notPurging(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "state of the flow purging operation. 'purging' - purging operation is proceeding 'notPurging' - the purging operation completed, or not started yet." DEFVAL { notPurging } ::= { cseMcastCacheEntry 7 } cseMcastCacheStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status object used to manage rows in this table. When set to active(1), the flow purge is initiated, and the value of cseMcastCacheResult object becomes 'purging'. However, this object can be set to active(1) only after all the appropriate objects for this query as defined by the value set in the cseMcastCacheFlowType object, have also been set. Upon the completion of flow purge, the value of cseMcastCacheResult object changes to 'notPurging'. Once a row becomes active, values within the row cannot be modified, except by setting it to 'notInService' first, or deleting and re-creating it." ::= { cseMcastCacheEntry 8 } -- cseCef Group -- -- -- The cseCefFibTable cseCefFibTable OBJECT-TYPE SYNTAX SEQUENCE OF CseCefFibEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the information stored in the device's forwarding information base (FIB). FIB is a forwarding scheme that utilizes matching pattern to provide optimized lookup for efficient packet forwarding. It contains a forwarding table which consist of matching criteria for incoming traffic as well as information to forward traffic that matched defined criteria." ::= { cseCef 1 } cseCefFibEntry OBJECT-TYPE SYNTAX CseCefFibEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each row contains the IP address type, the final destination IP address, the final destination IP address mask as well as the FIB entry type." INDEX { cseCefFibIndex } ::= { cseCefFibTable 1 } CseCefFibEntry ::= SEQUENCE { cseCefFibIndex Unsigned32, cseCefFibAddrType InetAddressType, cseCefFibDestIp InetAddress, cseCefFibDestIpMask InetAddress, cseCefFibType INTEGER } cseCefFibIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of this table entry." ::= { cseCefFibEntry 1 } cseCefFibAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of IP address denoted in cseCefFibDestIp and cseCefFibDestIpMask object." ::= { cseCefFibEntry 2 } cseCefFibDestIp OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The destination IP address specified in IP packet header." ::= { cseCefFibEntry 3 } cseCefFibDestIpMask OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The specified destination IP address mask." ::= { cseCefFibEntry 4 } cseCefFibType OBJECT-TYPE SYNTAX INTEGER { other(1), resolved(2), bridge(3), drop(4), connected(5), receive(6), wildcard(7), tunnel(8), default(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the FIB entry type. other(1) indicates that this FIB entry type is none of the following. resolved(2) indicates that IP traffic matched the destination prefix of this entry is associated with a valid next-hop address. bridge(3) indicates that IP traffic matched the destination prefix of this entry will be forwarded using Layer 2 look up result. drop(4) indicates that IP traffic matched the destination prefix of this entry will be dropped. connected(5) indicates that IP traffic matched the destination prefix of this entry is associated with a connected network. receive(6) indicates that IP traffic matched the destination prefix of this entry will be sent to a router interface. wildcard(7) indicates this FIB entry will match all traffic. tunnel(8) indicates this FIB entry applied to tunneling traffic. default(9) indicates that IP traffic matched the destination prefix of this entry will be forwarded using a default route." ::= { cseCefFibEntry 5 } -- The cseCefAdjacencyTable cseCefAdjacencyTable OBJECT-TYPE SYNTAX SEQUENCE OF CseCefAdjacencyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information stored in the device's adjacency table. Entry in this table is linked to entry of cseCefFibTable by its cseCefFibIndex object." ::= { cseCef 3 } cseCefAdjacencyEntry OBJECT-TYPE SYNTAX CseCefAdjacencyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each row contains next hop IP address, next-hop Ethernet address, adjacency type, and number of bytes and packets transmitted to each adjacency entry. Next hop encapsulation type and MTU value are also available if supported by the device." INDEX { cseCefFibIndex, cseCefAdjacencyIndex } ::= { cseCefAdjacencyTable 1 } CseCefAdjacencyEntry ::= SEQUENCE { cseCefAdjacencyIndex Unsigned32, cseCefAdjacencyAddrType InetAddressType, cseCefAdjacencyNextHopIp InetAddress, cseCefAdjacencyNextHopMac MacAddress, cseCefAdjacencyNextHopIfIndex InterfaceIndexOrZero, cseCefAdjacencyType INTEGER, cseCefAdjacencyPkts Counter64, cseCefAdjacencyOctets Counter64, cseCefAdjacencyEncap INTEGER, cseCefAdjacencyMTU Unsigned32 } cseCefAdjacencyIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The adjacency index of this table entry." ::= { cseCefAdjacencyEntry 1 } cseCefAdjacencyAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of IP address denoted in cseCefAdjacencyNextHopIp object." ::= { cseCefAdjacencyEntry 2 } cseCefAdjacencyNextHopIp OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The next hop IP address." ::= { cseCefAdjacencyEntry 3 } cseCefAdjacencyNextHopMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The next hop Ethernet address." ::= { cseCefAdjacencyEntry 4 } cseCefAdjacencyNextHopIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the next hop interface ifIndex." ::= { cseCefAdjacencyEntry 5 } cseCefAdjacencyType OBJECT-TYPE SYNTAX INTEGER { other(1), punt(2), glean(3), drop(4), null(5), noRewrite(6), forceDrop(7), connect(8), unresolved(9), loopback(10), tunnel(11) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates this adjacency entry type. other(1) indicates the adjacency entry type is none of the following. punt(2) indicates entry that sends traffic to the router. glean(3) indicates entry that needs to be gleaned for incoming traffic. drop(4) indicates entry that drops packets. null(5) indicates entry that drops packets destined for the Null0 interface. noRewrite(6) indicates entry that sends traffic to the router when rewrite information is incomplete. forceDrop(7) indicates entry that drop packets due to ARP throttling. connect(8) indicates entry that contains complete rewrite information. unresolved(9) indicates entry that next hop traffic is unresolved. loopback(10) indicates entry that drops packets destined for loopback interface. tunnel(11) indicates entry that next hop traffic is through a tunnel." ::= { cseCefAdjacencyEntry 6 } cseCefAdjacencyPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the number of Layer 3 packets transmitted to this adjacency entry." ::= { cseCefAdjacencyEntry 7 } cseCefAdjacencyOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the number of Layer 3 octets transmitted to this adjacency entry." ::= { cseCefAdjacencyEntry 8 } cseCefAdjacencyEncap OBJECT-TYPE SYNTAX INTEGER { arpa(1), raw(2), sap(3), snap(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the next hop destination encapsulation type. arpa(1) indicates that next hop destination used ARPA encapsulation type to forward packets. raw(2) indicates that next hop destination used RAW encapsulation type to forward packets. sap(3) indicates that next hop destination used SAP encapsulation type to forward packets. snap(4) indicates that next hop destination used SNAP encapsulation type to forward packets." ::= { cseCefAdjacencyEntry 9 } cseCefAdjacencyMTU OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the next hop destination MTU value." ::= { cseCefAdjacencyEntry 10 } -- cseTcamUsage group -- -- -- The cseTcamUsageTable cseTcamUsageTable OBJECT-TYPE SYNTAX SEQUENCE OF CseTcamUsageEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the resource usage of TCAM (Ternary Content Addressable Memory) in the device. Not all the resource types denoted by cseTcamResourceType object are supported. If that is the case, the corresponding row for that type will not be instantiated in this table." ::= { cseTcamUsage 1 } cseTcamUsageEntry OBJECT-TYPE SYNTAX CseTcamUsageEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each row contains a short description of the resource type, the total amount of TCAM allocated for that type as well as the amount of allocated resource has been used up." INDEX { entPhysicalIndex, cseTcamResourceType } ::= { cseTcamUsageTable 1 } CseTcamUsageEntry ::= SEQUENCE { cseTcamResourceType INTEGER, cseTcamResourceDescr SnmpAdminString, cseTcamResourceUsed Unsigned32, cseTcamResourceTotal Unsigned32 } cseTcamResourceType OBJECT-TYPE SYNTAX INTEGER { aclStorageMask(1), aclStorageValue(2), aclDynamicStorageMask(3), aclDynamicStorageValue(4), qosStorageMask(5), qosStorageValue(6), qosDynamicStorageMask(7), qosDynamicStorageValue(8), l4PortOperator(9), interfaceMapping(10), ingressInterfaceMapping(11), egressInterfaceMapping(12), louSource(13), louDestination(14), andOr(15), orAnd(16), aclAdjacency(17), aclHighStorageMask(18), aclHighStorageValue(19), aclLowStorageMask(20), aclLowStorageValue(21), qosHighStorageMask(22), qosHighStorageValue(23), qosLowStorageMask(24), qosLowStorageValue(25), sgacl(26), accounting(27), ipv6Ext(28), ethertype(29), destInfo(30), dgtSgtRegion(31), anyAnyRegion(32), tcamALabel(33), tcamBLabel(34), destInfoIn(35), destInfoOut(36), tcam0Bank0(37), tcam0Bank1(38), tcam1Bank0(39), tcam1Bank1(40), tcam0Aggregate(41), tcam1Aggregate(42), bank0Aggregate(43), bank1Aggregate(44), lou(45), bothLouOperands(46), singleLouOperands(47), louL4SourcePort(48), louL4DstPort(49), louL3PacketLength(50), louIpTos(51), louIpDscp(52), louIpPrecedence(53), louIpTtl(54), tcpFlags(55), l4DynamicProtocolCam(56), macEtypeOrProtoCam(57), nonL4OpLabelsTcam0(58), nonL4OpLabelsTcam1(59), l4OpLabelTcam0(60), l4OpLabelTcam1(61), ingressDestInfoTable(62), egressDestInfoTable(63), ingressTcam(64), ingressIpv6Tcam(65), ingressLou(66), ingressBothLouOperands(67), ingressSingleLouOperands(68), ingressLouL4SourcePort(69), ingressLouL4DstPort(70), ingressLouL3PacketLength(71), ingressLouL3Ttl(72), ingressLouL2Ttl(73), ingressTcpFlags(74), egressTcam(75), egressIpv6Tcam(76), egressLou(77), egressBothLouOperands(78), egressSingleLouOperands(79), egressLouL4SourcePort(80), egressLouL4DstPort(81), egressLouL3PacketLength(82), egressLouL3Ttl(83), egressLouL2Ttl(84), egressTcpFlags(85) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The resource type which take up TCAM space. aclStorageMask(1) indicates that TCAM space is allocated to store ACL masks. aclStorageValue(2) indicates that TCAM space is allocated to store ACL value. aclDynamicStorageMask(3) indicates that TCAM space is allocated to dynamically store ACL masks. aclDynamicStorageValue(4) indicates that TCAM space is allocated to dynamically store ACL values. qosStorageMask(5) indicates that TCAM space is allocated to store QoS masks. qosStorageValue(6) indicates that TCAM space is allocated to store QoS value. qosDynamicStorageMask(7) indicates that TCAM space is allocated to dynamically store QoS masks. qosDynamicStorageValue(8) indicates that TCAM space is allocated to dynamically store QoS values. l4PortOperator(9) indicates that TCAM space is allocated for layer 4 port operators purpose. interfaceMapping(10) indicates that TCAM space is allocated for interface mapping purpose. ingressInterfaceMapping(11) indicates that TCAM space is allocated for ingress interface mapping purpose. egressInterfaceMapping(12) indicates that TCAM space is allocated for egress interface mapping purpose. louSource(13) indicates that TCAM space is allocated as source LOUs (Logical Operation Unit). louDestination(14) indicates that TCAM space is allocated as destination LOUs. andOr(15) indicates that TCAM space is allocated for ANDOR purpose. orAnd(16) indicates that TCAM space is allocated for ORAND purpose. aclAdjacency(17) indicates that TCAM space is allocated for ACL adjacency purpose. aclHighStorageMask(18) indicates that high bank TCAM space is allocated to store ACL masks. aclHighStorageValue(19) indicates that high bank TCAM space is allocated to store ACL value. aclLowStorageMask(20) indicates that low bank TCAM space is allocated to store ACL masks. aclLowStorageValue(21) indicates that low bank TCAM space is allocated to store ACL values. qosHighStorageMask(22) indicates that high bank TCAM space is allocated to store QoS masks. qosHighStorageValue(23) indicates that high bank TCAM space is allocated to store QoS value. qosLowStorageMask(24) indicates that low bank TCAM space is allocated to store QoS masks. qosLowStorageValue(25) indicates that low bank TCAM space is allocated to store QoS values. sgacl(26) indicates that TCAM space is allocated for SGACL (Security Group Access Control List) purpose. accounting(27) indicates that TCAM space is allocated for accounting purpose such as AS (Autonomous System) based accounting, classification based accounting. ipv6Ext(28) indicates that TCAM space is allocated for IPv6 Extended Header lookup purpose. ethertype(29) indicates that TCAM space is allocated for layer2 ethertype lookup purpose. destInfo(30) indicates that TCAM space is allocated for destination information lookup purpose. dgtSgtRegion(31) indicates that TCAM space is allocated for specific SGT (Secutiry Group Tag), DGT (Destination Group Tag) pairs. anyAnyRegion(32) indicates that TCAM space is allocated for SGT (Secutiry Group Tag), DGT (Destination Group Tag) pairs with one or both of them as ANY. tcamALabel(33) indicates that TCAM space is allocated for labels used by TCAM A entries. tcamBLabel(34) indicates that TCAM space is allocated for labels used by TCAM B entries. destInfoIn(35) indicates that TCAM space is allocated for destination information table for IFE (Ingress Forwarding Engine) ACL redirects. destInfoOut(36) indicates that TCAM space is allocated for destination information table for OFE (Output/Egress Forwarding Engine) ACL redirects. tcam0Bank0(37) indicates that TCAM space is allocated for TCAM 0 Bank 0. tcam0Bank1(38) indicates that TCAM space is allocated for TCAM 0 Bank 1. tcam1Bank0(39) indicates that TCAM space is allocated for TCAM 1 Bank 0. tcam1Bank1(40) indicates that TCAM space is allocated for TCAM 1 Bank 1. tcam0Aggregate(41) indicates that TCAM space is allocated for the aggregate of Bank 0 and Bank 1 on TCAM 0. tcam1Aggregate(42) indicates that TCAM space is allocated for the aggregate of Bank 0 and Bank 1 on TCAM 1. bank0Aggregate(43) indicates that TCAM space is allocated for the aggregate of TCAM 0 and TCAM 1 for Bank 0. bank1Aggregate(44) indicates that TCAM space is allocated for the aggregate of TCAM 0 and TCAM 1 for Bank 1. lou(45) indicates that TCAM space is allocated for LOUs (Logical Operation Unit). bothLouOperands(46) indicates that TCAM space is allocated for LOUs with both operands. singleLouOperands(47) indicates that TCAM space is allocated for LOUs with single operands. louL4SourcePort(48) indicates that TCAM space is allocated for LOUs with L4 source port in comparison. louL4DstPort(49) indicates that TCAM space is allocated for LOUs with L4 destination port in comparison. louL3PacketLength(50) indicates that TCAM space is allocated for LOUs with L3 Length in comparison. louIpTos(51) indicates that TCAM space is allocated for LOUs with IP ToS (Type of Service) in comparison. louIpDscp(52) indicates that TCAM space is allocated for LOUs with IP DSCP (Differentiated Services Code Point) in comparison. louIpPrecedence(53) indicates that TCAM space is allocated for LOUs with IP Precedence in comparison. louIpTtl(54) indicates that TCAM space is allocated for LOUs with IP TTL in comparison. tcpFlags(55) indicates that TCAM space is allocated for TCP Flags. l4DynamicProtocolCam(56) indicates that TCAM space is allocated for L4 Dynamic Protocol CAM. macEtypeOrProtoCam(57) indicates that TCAM space is allocated for MAC Etype or Protocol CAM. nonL4OpLabelsTcam0(58) indicates that TCAM space is allocated for labels without using any L4 operator resources like LOUs or TCP Flags for TCAM 0. nonL4OpLabelsTcam1(59) indicates that TCAM space is allocated for labels without using any L4 operator resources like LOUs or TCP Flags for TCAM 1. l4OpLabelTcam0(60) indicates that TCAM space is allocated for labels using any L4 operator resources like LOUs or TCP Flags for TCAM 0. l4OpLabelTcam1(61) indicates that TCAM space is allocated for labels using any L4 operator resources like LOUs or TCP Flags for TCAM 1. ingressDestInfoTable(62) indicates that TCAM space is allocated for Ingress Destination Info Table. egressDestInfoTable(63) indicates that TCAM space is allocated for Egress Destination Info Table. ingressTcam(64) indicates that ingress TCAM resource utilization. ingressIpv6Tcam(65) indicates that ingress TCAM space is allocated for IPv6 compression. ingressLou(66) indicates that ingress TCAM space is allocated for LOUs (Logical Operation Unit). ingressBothLouOperands(67) indicates that ingress TCAM space is allocated for LOUs with both operands. ingressSingleLouOperands(68) indicates that ingress TCAM space is allocated for LOUs with single operands. ingressLouL4SourcePort(69) indicates that ingress TCAM space is allocated for LOUs with L4 source port in comparison. ingressLouL4DstPort(70) indicates that ingress TCAM space is allocated for LOUs with L4 destination port in comparison. ingressLouL3PacketLength(71) indicates that ingress TCAM space is allocated for LOUs with L3 Length in comparison. ingressLouL3Ttl(72) indicates that ingress TCAM space is allocated for LOUs with L3 TTL in comparison. ingressLouL2Ttl(73) indicates that ingress TCAM space is allocated for LOUs with L2 TTL in comparison. ingressTcpFlags(74) indicates that ingress TCAM space is allocated for TCP Flags. egressTcam(75) indicates that egress TCAM resource utilization. egressIpv6Tcam(76) indicates that egress TCAM space is allocated for IPv6 compression. egressLou(77)indicates that egress TCAM space is allocated for LOUs (Logical Operation Unit). egressBothLouOperands(78) indicates that egress TCAM space is allocated for LOUs with both operands. egressSingleLouOperands(79) indicates that egress TCAM space is allocated for LOUs with single operands. egressLouL4SourcePort(80) indicates that egress TCAM space is allocated for LOUs with L4 source port in comparison. egressLouL4DstPort(81) indicates that egress TCAM space is allocated for LOUs with L4 destination port in comparison. egressLouL3PacketLength(82) indicates that egress TCAM space is allocated for LOUs with L3 Length in comparison. egressLouL3Ttl(83) indicates that egress TCAM space is allocated for the LOUs with L3 TTL in comparison. egressLouL2Ttl(84) indicates that egress TCAM space is allocated for LOUs with L2 TTL in comparison. egressTcpFlags(85) indicates that egress TCAM space is allocated for TCP Flags." ::= { cseTcamUsageEntry 1 } cseTcamResourceDescr OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The short description of the resource type." ::= { cseTcamUsageEntry 2 } cseTcamResourceUsed OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of TCAM resource has been used up for this resource type." ::= { cseTcamUsageEntry 3 } cseTcamResourceTotal OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total amount of TCAM resource is allocated for this resource type." ::= { cseTcamUsageEntry 4 } -- cseMet group -- -- -- The cseMetUsageTable cseMetUsageTable OBJECT-TYPE SYNTAX SEQUENCE OF CseMetUsageEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the resource usage of MET (Multicast Expansion Table) in the device." ::= { cseMet 1 } cseMetUsageEntry OBJECT-TYPE SYNTAX CseMetUsageEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each row contains the total number of entries in each MET, the number of free entries in unallocated as well as allocated space of the MET. Each row represents MET data maintained by each module (identified by its entPhysicalIndex) which is capable of this feature." INDEX { entPhysicalIndex, cseMetIndex } ::= { cseMetUsageTable 1 } CseMetUsageEntry ::= SEQUENCE { cseMetIndex Unsigned32, cseMetTotalEntries Unsigned32, cseMetUnallocatedSpcFreeEntries Unsigned32, cseMetAllocatedSpcFreeEntries Unsigned32 } cseMetIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "A value uniquely identifies a MET in a module." ::= { cseMetUsageEntry 1 } cseMetTotalEntries OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of entries in this MET." ::= { cseMetUsageEntry 2 } cseMetUnallocatedSpcFreeEntries OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of free entries reside in unallocated space of this MET." ::= { cseMetUsageEntry 3 } cseMetAllocatedSpcFreeEntries OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of free entries reside in allocated space of this MET." ::= { cseMetUsageEntry 4 } -- Notifications cseMIBNotifications OBJECT IDENTIFIER ::= { ciscoSwitchEngineMIB 2 } -- no notifications defined -- -- Conformance cseMIBConformance OBJECT IDENTIFIER ::= { ciscoSwitchEngineMIB 3 } cseMIBCompliances OBJECT IDENTIFIER ::= { cseMIBConformance 1 } cseMIBGroups OBJECT IDENTIFIER ::= { cseMIBConformance 2 } -- compliance statements cseMIBCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the CISCO-SWITCH_ENGINE-MIB MIB." MODULE -- this module MANDATORY-GROUPS { cseStatisticsGroup } GROUP cseRouterGroup DESCRIPTION "This group is mandatory only for those switches which support layer 3 switching in the system." GROUP cseVlanStatisticsGroup DESCRIPTION "This group is mandatory only for those switches which can provide per-vlan statistics." GROUP cseFlowMgmtGroup DESCRIPTION "This group is mandatory only for those switches which support layer 3 switching in the system." GROUP cseFlowMcastMgmtGroup DESCRIPTION "This group is mandatory only for those switches which support layer 3 IP multicast switching in the system." GROUP cseUcastCachePurgeGroup DESCRIPTION "This group is mandatory only for those switches which supports IP/IPX unicast flow cache purging in the system." GROUP cseMcastCachePurgeGroup DESCRIPTION "This group is mandatory only for those switches which supports IP multicast flow cache purging in the system." ::= { cseMIBCompliances 1 } cseMIBCompliance2 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the CISCO-SWITCH-ENGINE-MIB MIB." MODULE -- this module MANDATORY-GROUPS { cseStatisticsGroup } GROUP cseRouterGroup DESCRIPTION "This group is mandatory only for those switches which support layer 3 switching in the system." GROUP cseVlanStatisticsGroup DESCRIPTION "This group is mandatory only for those switches which can provide per-vlan statistics." GROUP cseFlowMgmtGroup DESCRIPTION "This group is mandatory only for those switches which support layer 3 switching in the system." GROUP cseFlowMcastMgmtGroup DESCRIPTION "This group is mandatory only for those switches which support layer 3 IP multicast switching in the system." GROUP cseUcastCachePurgeGroup DESCRIPTION "This group is mandatory only for those switches which supports IP/IPX unicast flow cache purging in the system." GROUP cseMcastCachePurgeGroup DESCRIPTION "This group is mandatory only for those switches which supports IP multicast flow cache purging in the system." GROUP cseFlowMgmtOperStatusGroup DESCRIPTION "This group is mandatory only for those switches which support operating status on aging time for flows used in L3 switching." ::= { cseMIBCompliances 2 } cseMIBCompliance3 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the CISCO-SWITCH-ENGINE-MIB MIB." MODULE -- this module MANDATORY-GROUPS { cseStatisticsGroup } GROUP cseRouterGroup DESCRIPTION "This group is mandatory only for those switches which support layer 3 switching in the system." GROUP cseVlanStatisticsGroup DESCRIPTION "This group is mandatory only for those switches which can provide per-vlan statistics." GROUP cseFlowMgmtGroup DESCRIPTION "This group is mandatory only for those switches which support layer 3 switching in the system." GROUP cseFlowMcastMgmtGroup DESCRIPTION "This group is mandatory only for those switches which support layer 3 IP multicast switching in the system." GROUP cseUcastCachePurgeGroup DESCRIPTION "This group is mandatory only for those switches which supports IP/IPX unicast flow cache purging in the system." GROUP cseFlowMgmtOperStatusGroup DESCRIPTION "This group is mandatory only for those switches which support operating status on aging time for flows used in L3 switching." GROUP cse4kVlanGroup DESCRIPTION "This group must be implemented by the devices which support the range of VlanIndex between 1024 and 4095" ::= { cseMIBCompliances 3 } cseMIBCompliance4 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the CISCO-SWITCH-ENGINE-MIB MIB." MODULE -- this module MANDATORY-GROUPS { cseStatisticsGroup } GROUP cseRouterGroup DESCRIPTION "This group is mandatory only for those switches which support layer 3 switching in the system." GROUP cseVlanStatisticsGroup DESCRIPTION "This group is mandatory only for those switches which can provide per-vlan statistics." GROUP cseFlowMgmtGroup DESCRIPTION "This group is mandatory only for those switches which support layer 3 switching in the system." GROUP cseFlowMcastMgmtGroup DESCRIPTION "This group is mandatory only for those switches which support layer 3 IP multicast switching in the system." GROUP cseUcastCachePurgeGroup DESCRIPTION "This group is mandatory only for those switches which supports IP/IPX unicast flow cache purging in the system." GROUP cseMcastCachePurgeGroup DESCRIPTION "This group is mandatory only for those switches which supports IP multicast flow cache purging in the system." GROUP cseFlowMgmtOperStatusGroup DESCRIPTION "This group is mandatory only for those switches which support operating status on aging time for flows used in L3 switching." GROUP cse4kVlanGroup DESCRIPTION "This group must be implemented by the devices which support the range of VlanIndex between 1024 and 4095" GROUP cseNDEMandatoryGroup DESCRIPTION "This group is mandatory for those switched which support Netflow Data Export" GROUP cseNDESingleFilterGroup DESCRIPTION "This group is mandatory in agents for which the value of cseNetflowLSFilterSupport is single." GROUP cseNDEMultipleFiltersGroup DESCRIPTION "This group is mandatory in agents for which the value of cseNetflowLSFilterSupport is multiple." GROUP cseProtocolFilterGroup DESCRIPTION "Implementation of this group is optional." GROUP cseStatisticsGroup2 DESCRIPTION "Implementation of this group is optional." OBJECT cseNetflowLSFilterSelection MIN-ACCESS read-only DESCRIPTION "Write access is not required, for systems which support just one include and one exclude filter." OBJECT cseNetflowLSFilterStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required, for systems which support just one include and one exclude filter" ::= { cseMIBCompliances 4 } cseMIBCompliance5 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the CISCO-SWITCH-ENGINE-MIB MIB." MODULE -- this module MANDATORY-GROUPS { cseStatisticsGroup } GROUP cseRouterGroup DESCRIPTION "This group is mandatory only for those switches which support layer 3 switching in the system." GROUP cseVlanStatisticsGroup DESCRIPTION "This group is mandatory only for those switches which can provide per-vlan statistics." GROUP cseFlowMgmtGroupRev1 DESCRIPTION "This group is mandatory only for those switches which support layer 3 switching in the system." GROUP cseFlowMcastMgmtGroup DESCRIPTION "This group is mandatory only for those switches which support layer 3 IP multicast switching in the system." GROUP cseUcastCachePurgeGroup DESCRIPTION "This group is mandatory only for those switches which supports IP/IPX unicast flow cache purging in the system." GROUP cseMcastCachePurgeGroup DESCRIPTION "This group is mandatory only for those switches which supports IP multicast flow cache purging in the system." GROUP cseFlowMgmtOperStatusGroup DESCRIPTION "This group is mandatory only for those switches which support operating status on aging time for flows used in L3 switching." GROUP cse4kVlanGroup DESCRIPTION "This group must be implemented by the devices which support the range of VlanIndex between 1024 and 4095" GROUP cseNDEMandatoryGroup DESCRIPTION "This group is mandatory for those switched which support Netflow Data Export" GROUP cseNDESingleFilterGroup DESCRIPTION "This group is mandatory in agents for which the value of cseNetflowLSFilterSupport is single." GROUP cseNDEMultipleFiltersGroup DESCRIPTION "This group is mandatory in agents for which the value of cseNetflowLSFilterSupport is multiple." GROUP cseProtocolFilterGroup DESCRIPTION "Implementation of this group is optional." GROUP cseStatisticsGroup2 DESCRIPTION "Implementation of this group is optional." OBJECT cseNetflowLSFilterSelection MIN-ACCESS read-only DESCRIPTION "Write access is not required, for systems which support just one include and one exclude filter." OBJECT cseNetflowLSFilterStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required, for systems which support just one include and one exclude filter" ::= { cseMIBCompliances 5 } cseMIBCompliance6 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the CISCO-SWITCH-ENGINE-MIB MIB." MODULE -- this module MANDATORY-GROUPS { cseStatisticsGroup } GROUP cseRouterGroup DESCRIPTION "This group is mandatory only for those switches which support layer 3 switching in the system." GROUP cseVlanStatisticsGroup DESCRIPTION "This group is mandatory only for those switches which can provide per-vlan statistics." GROUP cseFlowMgmtGroupRev1 DESCRIPTION "This group is mandatory only for those switches which support layer 3 switching in the system." GROUP cseFlowMcastMgmtGroup DESCRIPTION "This group is mandatory only for those switches which support layer 3 IP multicast switching in the system." GROUP cseUcastCachePurgeGroup DESCRIPTION "This group is mandatory only for those switches which supports IP/IPX unicast flow cache purging in the system." GROUP cseMcastCachePurgeGroup DESCRIPTION "This group is mandatory only for those switches which supports IP multicast flow cache purging in the system." GROUP cseFlowMgmtOperStatusGroup DESCRIPTION "This group is mandatory only for those switches which support operating status on aging time for flows used in L3 switching." GROUP cse4kVlanGroup DESCRIPTION "This group must be implemented by the devices which support the range of VlanIndex between 1024 and 4095" GROUP cseNDEMandatoryGroup DESCRIPTION "This group is mandatory for those switched which support Netflow Data Export" GROUP cseNDESingleFilterGroupRev1 DESCRIPTION "This group is mandatory in agents for which the value of cseNetflowLSFilterSupport is single." GROUP cseNDEMultipleFiltersGroup DESCRIPTION "This group is mandatory in agents for which the value of cseNetflowLSFilterSupport is multiple." GROUP cseProtocolFilterGroup DESCRIPTION "Implementation of this group is optional." GROUP cseStatisticsGroup2 DESCRIPTION "Implementation of this group is optional." GROUP cseFlowMgmtExtGroup2 DESCRIPTION "This group is mandatory only for those switches which support layer 3 switching in the system." OBJECT cseNetflowLSFilterSelection MIN-ACCESS read-only DESCRIPTION "Write access is not required, for systems which support just one include and one exclude filter." OBJECT cseNetflowLSFilterStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required, for systems which support just one include and one exclude filter" ::= { cseMIBCompliances 6 } cseMIBCompliance7 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the CISCO-SWITCH-ENGINE-MIB MIB." MODULE -- this module MANDATORY-GROUPS { cseStatisticsGroup } GROUP cseRouterGroup DESCRIPTION "This group is mandatory only for those switches which support layer 3 switching in the system." GROUP cseVlanStatisticsGroup DESCRIPTION "This group is mandatory only for those switches which can provide per-vlan statistics." GROUP cseFlowMgmtGroupRev1 DESCRIPTION "This group is mandatory only for those switches which support layer 3 switching in the system." GROUP cseFlowMcastMgmtGroup1 DESCRIPTION "This group is mandatory only for those switches which support layer 3 IP multicast switching in the system." GROUP cseUcastCachePurgeGroup DESCRIPTION "This group is mandatory only for those switches which supports IP/IPX unicast flow cache purging in the system." GROUP cseMcastCachePurgeGroup DESCRIPTION "This group is mandatory only for those switches which supports IP multicast flow cache purging in the system." GROUP cseFlowMgmtOperStatusGroup DESCRIPTION "This group is mandatory only for those switches which support operating status on aging time for flows used in L3 switching." GROUP cse4kVlanGroup DESCRIPTION "This group must be implemented by the devices which support the range of VlanIndex between 1024 and 4095" GROUP cseNDEMandatoryGroup DESCRIPTION "This group is mandatory for those switched which support Netflow Data Export" GROUP cseNDESingleFilterGroupRev1 DESCRIPTION "This group is mandatory in agents for which the value of cseNetflowLSFilterSupport is single." GROUP cseNDEMultipleFiltersGroup DESCRIPTION "This group is mandatory in agents for which the value of cseNetflowLSFilterSupport is multiple." GROUP cseProtocolFilterGroup DESCRIPTION "Implementation of this group is optional." GROUP cseStatisticsGroup2 DESCRIPTION "Implementation of this group is optional." GROUP cseFlowMgmtExtGroup2 DESCRIPTION "This group is mandatory only for those switches which support layer 3 switching in the system." GROUP cseFlowMcastRtrMgmtGroup DESCRIPTION "Implementation of this group is optional." GROUP cseFlowMcastMgmtGroup2 DESCRIPTION "This group is mandatory only for those switches which support layer 3 IP multicast switching in the system." OBJECT cseNetflowLSFilterSelection MIN-ACCESS read-only DESCRIPTION "Write access is not required, for systems which support just one include and one exclude filter." OBJECT cseNetflowLSFilterStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required, for systems which support just one include and one exclude filter" ::= { cseMIBCompliances 7 } cseMIBCompliance8 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for the CISCO-SWITCH-ENGINE-MIB MIB." MODULE -- this module MANDATORY-GROUPS { cseStatisticsGroup } GROUP cseRouterGroup DESCRIPTION "This group is mandatory only for those switches which support layer 3 switching in the system." GROUP cseVlanStatisticsGroup DESCRIPTION "This group is mandatory only for those switches which can provide per-vlan statistics." GROUP cseFlowMgmtGroupRev1 DESCRIPTION "This group is mandatory only for those switches which support layer 3 switching in the system." GROUP cseFlowMcastMgmtGroup1 DESCRIPTION "This group is mandatory only for those switches which support layer 3 IP multicast switching in the system." GROUP cseUcastCachePurgeGroup DESCRIPTION "This group is mandatory only for those switches which supports IP/IPX unicast flow cache purging in the system." GROUP cseMcastCachePurgeGroup DESCRIPTION "This group is mandatory only for those switches which supports IP multicast flow cache purging in the system." GROUP cseFlowMgmtOperStatusGroup DESCRIPTION "This group is mandatory only for those switches which support operating status on aging time for flows used in L3 switching." GROUP cse4kVlanGroup DESCRIPTION "This group must be implemented by the devices which support the range of VlanIndex between 1024 and 4095" GROUP cseNDEMandatoryGroup DESCRIPTION "This group is mandatory for those switched which support Netflow Data Export" GROUP cseNDESingleFilterGroupRev1 DESCRIPTION "This group is mandatory in agents for which the value of cseNetflowLSFilterSupport is single." GROUP cseNDEMultipleFiltersGroup DESCRIPTION "This group is mandatory in agents for which the value of cseNetflowLSFilterSupport is multiple." GROUP cseProtocolFilterGroup DESCRIPTION "Implementation of this group is optional." GROUP cseStatisticsGroup2 DESCRIPTION "Implementation of this group is optional." GROUP cseFlowMgmtExtGroup2 DESCRIPTION "This group is mandatory only for those switches which support layer 3 switching in the system." GROUP cseFlowMcastRtrMgmtGroup DESCRIPTION "Implementation of this group is optional." GROUP cseFlowMcastMgmtGroup2 DESCRIPTION "This group is mandatory only for those switches which support layer 3 IP multicast switching in the system." GROUP cseCacheStatisticsGroup DESCRIPTION "This group is mandatory only for those switches which support switch engine statistics on flow cache entries in the system." GROUP cseL3SwitchedPktsPerSecGroup DESCRIPTION "This group is mandatory only for those switches which support switch engine statistics on total number of packets switched per second in the system." GROUP cseStatisticsFlowGroup1 DESCRIPTION "This group is mandatory only for those switches which support switch engine statistics on total number of Ipv4 flow entries." OBJECT cseNetflowLSFilterSelection MIN-ACCESS read-only DESCRIPTION "Write access is not required, for systems which support just one include and one exclude filter." OBJECT cseNetflowLSFilterStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required, for systems which support just one include and one exclude filter" ::= { cseMIBCompliances 8 } -- units of conformance cseStatisticsGroup OBJECT-GROUP OBJECTS { cseL2ForwardedLocalPkts, cseL2ForwardedLocalOctets, cseL2ForwardedTotalPkts, cseL2NewAddressLearns, cseL2AddrLearnFailures, cseL2DstAddrLookupMisses, cseL3SwitchedTotalPkts, cseL3SwitchedTotalOctets, cseL3CandidateFlowHits, cseL3EstablishedFlowHits, cseL3ActiveFlows, cseL3FlowLearnFailures, cseL3IntFlowInvalids, cseL3ExtFlowInvalids, cseL2HCOverflowForwardedLocalPkts, cseL2HCForwardedLocalPkts, cseL2HCOverflowForwardedTotalPkts, cseL2HCForwardedTotalPkts, cseL2HCOverflowIpPkts, cseL2HCIpPkts, cseL2HCOverflowIpxPkts, cseL2HCIpxPkts, cseL2HCOverflowAssignedProtoPkts, cseL2HCAssignedProtoPkts, cseL2HCOverflowOtherProtoPkts, cseL2HCOtherProtoPkts } STATUS current DESCRIPTION "A collection of objects providing switch engine statistics." ::= { cseMIBGroups 1 } cseStatisticsGroup2 OBJECT-GROUP OBJECTS { cseStatsFlowAged, cseStatsFlowPurged, cseStatsFlowParityFail, cseCacheUtilization } STATUS current DESCRIPTION "A collection of objects providing switch engine statistics on aged/purged flows, and the cache utilizations." ::= { cseMIBGroups 2 } cseVlanStatisticsGroup OBJECT-GROUP OBJECTS { cseL3VlanInPkts, cseL3VlanInOctets, cseL3VlanOutPkts, cseL3VlanOutOctets } STATUS current DESCRIPTION "A collection of objects providing per-vlan switch engine statistics, if supported." ::= { cseMIBGroups 3 } cseRouterGroup OBJECT-GROUP OBJECTS { cseRouterFlowMask, cseRouterName, cseRouterStatic, cseStaticRouterOwner, cseStaticRouterName, cseStaticRouterType, cseStaticRouterStatus, cseRouterIpxFlowMask, cseStaticIpxRouterOwner, cseStaticIpxRouterName, cseStaticIpxRouterStatus, cseRouterMac, cseRouterProtocol } STATUS current DESCRIPTION "A collection of objects providing information on routers which are used to support layer 3 switching in the system." ::= { cseMIBGroups 4 } cseFlowMgmtGroup OBJECT-GROUP OBJECTS { cseFlowEstablishedAgingTime, cseFlowFastAgingTime, cseFlowFastAgePktThreshold, cseFlowIPXEstablishedAgingTime, cseFlowMaxQueries, cseFlowQueryMask, cseFlowQueryTransport, cseFlowQuerySource, cseFlowQuerySourceMask, cseFlowQueryDestination, cseFlowQueryDestinationMask, cseFlowQueryRouterIndex, cseFlowQueryOwner, cseFlowQueryResultingRows, cseFlowQueryResultTotalPkts, cseFlowQueryResultTotalOctets, cseFlowQueryResultAvgDuration, cseFlowQueryResultAvgIdle, cseFlowQueryStatus, cseFlowQueryCreateTime, cseFlowDataSrcMac, cseFlowDataDstMac, cseFlowDataEncapType, cseFlowDataSource, cseFlowDataStaticFlow, cseFlowDataDestination, cseFlowDataDestVlan, cseFlowDataIpQOS, cseFlowDataIpQOSPolicy, cseFlowDataWhenCreated, cseFlowDataLastUsed, cseFlowDataPkts, cseFlowDataOctets, cseFlowSwitchStatus } STATUS deprecated DESCRIPTION "A collection of objects providing information for determining the L3 flow switching performance in the switching engine. There may be some platform specific limitations when performing a SET on some of these objects. The following are valid for Catalyst 5000 platforms: - cseFlowEstablishedAgingTime has a default value of 256. - cseFlowFastAgePktThreshold can only be set to 1, 3, 7, 15, 31 or 63 packets. If the packet threshold is not configured to one of these values, it will be adjusted to the closest value. - cseFlowFastAgingTime can be set to only values that are multiples of 8 in the range (0..128). If it is set to a value that is not multiple of 8, then the closest value that is a multiple of 8 will take effect. The default value for fast aging time is 32 seconds. (i.e. less than cseFlowFastAgePktThreshold number of packets were switched within 32 seconds after the an L3 flow entry was established). - cseFlowIPXEstablishedAgingTime has a default value of 256. cseFlowMgmtGroup object is superseded by cseFlowMgmtGroupRev1." ::= { cseMIBGroups 5 } cseNetflowLSGroup OBJECT-GROUP OBJECTS { cseNetflowLSExportHost, cseNetflowLSExportTransportNumber, cseNetflowLSExportStatus, cseNetflowLSExportDataSource, cseNetflowLSExportDataSourceMask, cseNetflowLSExportDataDest, cseNetflowLSExportDataDestMask, cseNetflowLSExportDataProtocol, cseNetflowLSExportDataFilterSelection, cseNetflowLSExportNDEVersionNumber } STATUS deprecated DESCRIPTION "A collection of objects providing information on the Netflow LAN switching Data Export feature, if supported. cseNetflowLSGroup object is superseded by cseNDESingleFilterGroupRev1." ::= { cseMIBGroups 6 } cseProtocolFilterGroup OBJECT-GROUP OBJECTS { cseProtocolFilterPortAdminStatus, cseProtocolFilterPortOperStatus, cseL2IpPkts, cseL2IpxPkts, cseL2AssignedProtoPkts, cseL2OtherProtoPkts } STATUS current DESCRIPTION "A collection of objects providing information on the Protocol filter feature, if supported." ::= { cseMIBGroups 7 } cseFlowMcastMgmtGroup OBJECT-GROUP OBJECTS { cseFlowMcastMaxQueries, cseFlowMcastQueryMask, cseFlowMcastQuerySrc, cseFlowMcastQueryGrp, cseFlowMcastQuerySrcVlan, cseFlowMcastQueryRtrIndex, cseFlowMcastQuerySkipNFlows, cseFlowMcastQueryOwner, cseFlowMcastQueryTotalFlows, cseFlowMcastQueryRows, cseFlowMcastQueryStatus, cseFlowMcastQueryCreateTime, cseFlowMcastResultSrc, cseFlowMcastResultGrp, cseFlowMcastResultSrcVlan, cseFlowMcastResultRtrIp, cseFlowMcastResultRtrMac, cseFlowMcastResultCreatedTS, cseFlowMcastResultLastUsedTS, cseFlowMcastResultPkts, cseFlowMcastResultOctets, cseFlowMcastResultDstVlans, cseFlowMcastSwitchStatus } STATUS deprecated DESCRIPTION "A collection of objects for querying IP multicast flows stored in hardware switching cache. cseFlowMcastMgmtGroup object is superseded by cseFlowMcastMgmtGroup1." ::= { cseMIBGroups 8 } cseUcastCachePurgeGroup OBJECT-GROUP OBJECTS { cseUcastCacheFlowType, cseUcastCacheTransport, cseUcastCacheDest, cseUcastCacheDestMask, cseUcastCacheSource, cseUcastCacheSrcMask, cseUcastCacheRtrIp, cseUcastCacheOwner, cseUcastCacheStatus, cseUcastCacheResult } STATUS current DESCRIPTION "A collection of objects providing IP/IPX unicast flow cache purging function." ::= { cseMIBGroups 9 } cseMcastCachePurgeGroup OBJECT-GROUP OBJECTS { cseMcastCacheFlowType, cseMcastCacheGrp, cseMcastCacheSrc, cseMcastCacheRtrIp, cseMcastCacheOwner, cseMcastCacheStatus, cseMcastCacheResult } STATUS current DESCRIPTION "A collection of objects providing IP multicast flow cache purge function." ::= { cseMIBGroups 10 } cseFlowMgmtOperStatusGroup OBJECT-GROUP OBJECTS { cseFlowOperEstablishedAgingTime, cseFlowOperFastAgingTime, cseFlowOperFastAgePktThreshold, cseFlowOperIPXAgingTime } STATUS current DESCRIPTION "A collection of objects providing operating status information on aging time for flows used in L3 switching." ::= { cseMIBGroups 11 } cse4kVlanGroup OBJECT-GROUP OBJECTS { cseFlowMcastResultDstVlans2k, cseFlowMcastResultDstVlans3k, cseFlowMcastResultDstVlans4k } STATUS current DESCRIPTION "A collection of objects providing information for VLANS with VlanIndex from 1024 to 4095." ::= { cseMIBGroups 12 } cseNDEMandatoryGroup OBJECT-GROUP OBJECTS { cseNetflowLSFilterSupport, cseNetflowLSExportStatus, cseNetflowLSExportNDEVersionNumber } STATUS current DESCRIPTION "A collection of objects providing information on the type of filter support, status and the version of NDE used." ::= { cseMIBGroups 13 } cseNDESingleFilterGroup OBJECT-GROUP OBJECTS { cseNetflowLSExportHost, cseNetflowLSExportTransportNumber, cseNetflowLSExportDataSource, cseNetflowLSExportDataSourceMask, cseNetflowLSExportDataDest, cseNetflowLSExportDataDestMask, cseNetflowLSExportDataProtocol, cseNetflowLSExportDataFilterSelection } STATUS deprecated DESCRIPTION "A collection of objects providing information on the Netflow LAN switching Data Export feature, with a single host and a single filter support. cseNDESingleFilterGroup object is superseded by cseNDESingleFilterGroupRev1." ::= { cseMIBGroups 14 } cseNDEMultipleFiltersGroup OBJECT-GROUP OBJECTS { cseNetflowLSFilterDataSource, cseNetflowLSFilterDataSourceMask, cseNetflowLSFilterDataDest, cseNetflowLSFilterDataDestMask, cseNetflowLSFilterDataProtocol, cseNetflowLSFilterSelection, cseNetflowLSFilterStatus } STATUS current DESCRIPTION "A collection of objects providing information on the Netflow LAN switching Data Export feature, with multiple filter support." ::= { cseMIBGroups 15 } cseFlowMgmtGroupRev1 OBJECT-GROUP OBJECTS { cseFlowEstablishedAgingTime, cseFlowFastAgingTime, cseFlowFastAgePktThreshold, cseFlowIPXEstablishedAgingTime, cseFlowMaxQueries, cseFlowQueryMask, cseFlowQueryTransport, cseFlowQuerySource, cseFlowQuerySourceMask, cseFlowQueryDestination, cseFlowQueryDestinationMask, cseFlowQueryRouterIndex, cseFlowQueryOwner, cseFlowQueryResultingRows, cseFlowQueryResultTotalPkts, cseFlowQueryResultTotalOctets, cseFlowQueryResultAvgDuration, cseFlowQueryResultAvgIdle, cseFlowQueryStatus, cseFlowQueryCreateTime, cseFlowQueryTotalFlows, cseFlowDataSrcMac, cseFlowDataDstMac, cseFlowDataEncapType, cseFlowDataSource, cseFlowDataStaticFlow, cseFlowDataDestination, cseFlowDataDestVlan, cseFlowDataIpQOS, cseFlowDataIpQOSPolicy, cseFlowDataWhenCreated, cseFlowDataLastUsed, cseFlowDataPkts, cseFlowDataOctets, cseFlowSwitchStatus } STATUS current DESCRIPTION "A collection of objects providing information for determining the L3 flow switching performance in the switching engine. There may be some platform specific limitations when performing a SET on some of these objects. The following are valid for Catalyst 5000 platforms: - cseFlowEstablishedAgingTime has a default value of 256. - cseFlowFastAgePktThreshold can only be set to 1, 3, 7, 15, 31 or 63 packets. If the packet threshold is not configured to one of these values, it will be adjusted to the closest value. - cseFlowFastAgingTime can be set to only values that are multiples of 8 in the range (0..128). If it is set to a value that is not multiple of 8, then the closest value that is a multiple of 8 will take effect. The default value for fast aging time is 32 seconds. (i.e. less than cseFlowFastAgePktThreshold number of packets were switched within 32 seconds after the an L3 flow entry was established). - cseFlowIPXEstablishedAgingTime has a default value of 256." ::= { cseMIBGroups 16 } cseL3ErrorsGroup OBJECT-GROUP OBJECTS { cseIpPlenErrors, cseIpTooShortErrors, cseIpCheckSumErrors, cseIpxPlenErrors, cseIpxTooShortErrors } STATUS current DESCRIPTION "A collection of objects providing the IP and IPX error statistics." ::= { cseMIBGroups 17 } cseBridgedFlowGroup OBJECT-GROUP OBJECTS { cseFlowBridgedFlowStatsEnable } STATUS current DESCRIPTION "A collection of objects control the reporting of intra-vlan bridged flow statistics." ::= { cseMIBGroups 18 } cseVlanStatisticsExtGroup OBJECT-GROUP OBJECTS { cseL3VlanInUnicastPkts, cseL3VlanInUnicastOctets, cseL3VlanOutUnicastPkts, cseL3VlanOutUnicastOctets } STATUS current DESCRIPTION "A collection of objects providing additional per-vlan switch engine statistics, if supported." ::= { cseMIBGroups 19 } cseProtocolFilterExtGroup OBJECT-GROUP OBJECTS { cseProtocolFilterEnable } STATUS current DESCRIPTION "A collection of objects providing additional information on the Protocol filter feature, if supported." ::= { cseMIBGroups 20 } cseFlowMgmtExtGroup OBJECT-GROUP OBJECTS { cseFlowIPFlowMask, cseFlowIPXFlowMask } STATUS current DESCRIPTION "A collection of objects providing additional information on the L3 flow switching in the switching engine." ::= { cseMIBGroups 21 } cseFlowMgmtExtGroup1 OBJECT-GROUP OBJECTS { cseFlowLongAgingTime, cseFlowExcludeProtocol, cseFlowExcludeStatus } STATUS current DESCRIPTION "A collection of objects providing additional information on the L3 flow switching in the switching engine." ::= { cseMIBGroups 22 } cseNDEReportGroup OBJECT-GROUP OBJECTS { cseNetFlowIfIndexEnable } STATUS current DESCRIPTION "A collection of objects providing the configuration on NDE ifIndex report feature." ::= { cseMIBGroups 23 } cseStatisticsFlowGroup OBJECT-GROUP OBJECTS { cseFlowTotalFlows } STATUS current DESCRIPTION "A collection of object providing switch engine statistics on total number of installed flows." ::= { cseMIBGroups 24 } cseFlowMgmtExtGroup2 OBJECT-GROUP OBJECTS { cseFlowQuerySkipNFlows } STATUS current DESCRIPTION "A collection of objects providing additional information on the L3 flow switching in the switching engine." ::= { cseMIBGroups 25 } cseNDESingleFilterGroupRev1 OBJECT-GROUP OBJECTS { cseNetflowLSExportDataSource, cseNetflowLSExportDataSourceMask, cseNetflowLSExportDataDest, cseNetflowLSExportDataDestMask, cseNetflowLSExportDataProtocol, cseNetflowLSExportDataFilterSelection } STATUS current DESCRIPTION "A collection of objects providing information on the Netflow LAN switching Data Export feature, with a single filter support." ::= { cseMIBGroups 26 } cseCefFibAdjacencyGroup OBJECT-GROUP OBJECTS { cseCefFibAddrType, cseCefFibDestIp, cseCefFibDestIpMask, cseCefFibType, cseCefAdjacencyAddrType, cseCefAdjacencyNextHopIp, cseCefAdjacencyNextHopMac, cseCefAdjacencyNextHopIfIndex, cseCefAdjacencyType, cseCefAdjacencyPkts, cseCefAdjacencyOctets } STATUS current DESCRIPTION "A collection of objects providing FIB and adjacency information available in the device." ::= { cseMIBGroups 27 } cseCefAdjacencyEncapGroup OBJECT-GROUP OBJECTS { cseCefAdjacencyEncap } STATUS current DESCRIPTION "A collection of object providing adjacency next hop encapsulation information available in the device." ::= { cseMIBGroups 28 } cseCefAdjacencyMTUGroup OBJECT-GROUP OBJECTS { cseCefAdjacencyMTU } STATUS current DESCRIPTION "A collection of object providing adjacency next hop MTU information available in the device." ::= { cseMIBGroups 29 } cseTcamUsageGroup OBJECT-GROUP OBJECTS { cseTcamResourceDescr, cseTcamResourceUsed, cseTcamResourceTotal } STATUS current DESCRIPTION "A collection of objects providing the resource usage information on TCAM available in the device." ::= { cseMIBGroups 30 } cseL3ErrorsLCGroup OBJECT-GROUP OBJECTS { cseLCIpPlenErrors, cseLCIpTooShortErrors, cseLCIpCheckSumErrors, cseLCIpxPlenErrors, cseLCIpxTooShortErrors } STATUS current DESCRIPTION "A collection of objects providing the IP and IPX error statistics." ::= { cseMIBGroups 31 } cseNetflowASInfoExportGroup OBJECT-GROUP OBJECTS { cseNetflowASInfoExportCtrl } STATUS current DESCRIPTION "A collection of object providing AS number information export control." ::= { cseMIBGroups 32 } cseNetflowPerVlanIfGroup OBJECT-GROUP OBJECTS { cseNetflowPerVlanIfGlobalEnable, cseNetflowPerVlanIfEnable } STATUS current DESCRIPTION "A collection of objects providing control of netflow entry creation per vlan." ::= { cseMIBGroups 33 } cseMetUsageGroup OBJECT-GROUP OBJECTS { cseMetTotalEntries, cseMetUnallocatedSpcFreeEntries, cseMetAllocatedSpcFreeEntries } STATUS current DESCRIPTION "A collection of objects providing MET utilization information." ::= { cseMIBGroups 34 } cseFlowMcastMgmtGroup1 OBJECT-GROUP OBJECTS { cseFlowMcastMaxQueries, cseFlowMcastQueryMask, cseFlowMcastQuerySrcVlan, cseFlowMcastQuerySkipNFlows, cseFlowMcastQueryOwner, cseFlowMcastQueryTotalFlows, cseFlowMcastQueryRows, cseFlowMcastQueryStatus, cseFlowMcastQueryCreateTime, cseFlowMcastResultSrcVlan, cseFlowMcastResultCreatedTS, cseFlowMcastResultLastUsedTS, cseFlowMcastResultPkts, cseFlowMcastResultOctets, cseFlowMcastResultDstVlans, cseFlowMcastSwitchStatus } STATUS current DESCRIPTION "A collection of objects for querying IP multicast flows stored in hardware switching cache." ::= { cseMIBGroups 35 } cseFlowMcastRtrMgmtGroup OBJECT-GROUP OBJECTS { cseFlowMcastQueryRtrIndex, cseFlowMcastResultRtrIp, cseFlowMcastResultRtrMac } STATUS current DESCRIPTION "A collection of objects for specifying the router based information while IP multicast flows stored in the hardware switching cache are queried." ::= { cseMIBGroups 36 } cseFlowMcastMgmtGroup2 OBJECT-GROUP OBJECTS { cseFlowMcastQueryMvrf, cseFlowMcastQueryAddrType, cseFlowMcastQuerySource, cseFlowMcastQueryGroup, cseFlowMcastResultMvrf, cseFlowMcastResultAddrType, cseFlowMcastResultGroup, cseFlowMcastResultSource, cseFlowMcastResultFlowType, cseFlowMcastResultHFlag1k2k, cseFlowMcastResultHFlag3k4k } STATUS current DESCRIPTION "A collection of objects for enhanced querying of IP multicast flows stored in hardware switching cache." ::= { cseMIBGroups 37 } cseCacheStatisticsGroup OBJECT-GROUP OBJECTS { cseCacheEntriesCreated, cseCacheEntriesFailed } STATUS current DESCRIPTION "A collection of objects providing switch engine statistics on the flow cache entries." ::= { cseMIBGroups 38 } cseL3SwitchedPktsPerSecGroup OBJECT-GROUP OBJECTS { cseL3SwitchedPktsPerSec, cseL3SwitchedAggrPktsPerSec } STATUS current DESCRIPTION "A collection of objects providing switch engine statistics on total number of packets switched per second." ::= { cseMIBGroups 39 } cseStatisticsFlowGroup1 OBJECT-GROUP OBJECTS { cseFlowTotalIpv4Flows } STATUS current DESCRIPTION "A collection of object providing switch engine statistics on total number of Ipv4 flow entries." ::= { cseMIBGroups 40 } END