-- ********************************************************************* -- CISCO-RSCN-MIB.my: Registered State Change Notificaton (RSCN) Mib -- -- September 2002, H K Vivek -- -- Copyright (c) 2002-2004, 2005, 2006, 2009 by cisco Systems Inc. -- All rights reserved. -- -- ********************************************************************* CISCO-RSCN-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Counter32, Integer32, Unsigned32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF TruthValue FROM SNMPv2-TC FcAddressId FROM CISCO-ST-TC vsanIndex FROM CISCO-VSAN-MIB FcGs3RejectReasonCode FROM CISCO-NS-MIB ciscoMgmt FROM CISCO-SMI; ciscoRscnMIB MODULE-IDENTITY LAST-UPDATED "200809010000Z" ORGANIZATION "Cisco Systems Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553 -NETS E-mail: cs-san@cisco.com" DESCRIPTION "The MIB module for the management of the Fibre Channel's Registered State Change Notification (RSCN) functionality, which is specified by FC-FLA and FC-FS. GLOSSARY : RSCN - Registered State Change Notification. RSCN Notifications are sent to Nx_ports and other switches to notify that an event has occured. SW_RSCN - Switch Registered State Change Notification. SW_RSCN Notifications are sent to neighbouring switches in a fabric to notify that an event has occured. ELS - Extended Link Service. RSCN Software module uses ELS frame formats to send RSCN messages. ILS - Inter Link Service. RSCN Software module uses ILS frame formats to send SW-RSCN messages." REVISION "200809010000Z" DESCRIPTION "modified rscnEventTov range from '1..2000' to '0.2000'." REVISION "200608170000Z" DESCRIPTION "Added following notifications -rscnIlsRxRejectReqNotify -rscnElsRxRejectReqNotify Added 2 new notification control objects: - rscnIlsRxRejectReqNotifyEnable - rscnElsRxRejectReqNotifyEnable Added rscnNotifyControlGroupSup1 OBJECT-GROUP Added rscnRejectNotifyGroup NOTIFICATION-GROUP Added rscnMIBComplianceRev3 MODULE-COMPLIANCE" REVISION "200505060000Z" DESCRIPTION "Added rscnEventTovTable." REVISION "200310160000Z" DESCRIPTION "Added rscnMultiPidTable." REVISION "200209200000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 292 } ciscoRscnMIBObjects OBJECT IDENTIFIER ::= { ciscoRscnMIB 1 } rscnMIBConformance OBJECT IDENTIFIER ::= { ciscoRscnMIB 2 } rscnConfiguration OBJECT IDENTIFIER ::= { ciscoRscnMIBObjects 1 } rscnStats OBJECT IDENTIFIER ::= { ciscoRscnMIBObjects 2 } rscnInformation OBJECT IDENTIFIER ::= { ciscoRscnMIBObjects 3 } rscnNotification OBJECT IDENTIFIER ::= { ciscoRscnMIBObjects 4 } rscnNotifications OBJECT IDENTIFIER ::= { rscnNotification 0 } -- State Change Registration Table rscnScrNumber OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Nx_Ports currently registered to receive RSCNs." ::= { rscnConfiguration 1 } rscnScrTable OBJECT-TYPE SYNTAX SEQUENCE OF RscnScrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of Nx_Ports that have registered to receive RSCNs on all VSANs configured on the local switch." ::= { rscnConfiguration 2 } rscnScrEntry OBJECT-TYPE SYNTAX RscnScrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) containing information about one Nx_Port which has registered to receive RSCNs on the VSAN indicated by vsanIndex." INDEX { vsanIndex, rscnScrFcId } ::= { rscnScrTable 1 } RscnScrEntry ::= SEQUENCE { rscnScrFcId FcAddressId, rscnScrRegType INTEGER } rscnScrFcId OBJECT-TYPE SYNTAX FcAddressId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Fibre Channel Identifier (FC-ID) of the subscribing Nx_Port." ::= { rscnScrEntry 1 } rscnScrRegType OBJECT-TYPE SYNTAX INTEGER { fromFabricCtrlr(1), fromNxPort(2), fromBoth(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the type of registration desired by the subscriber. 'fromFabricCtrlr' indicates RSCNs generated by the Fabric Controller. 'fromNxPort' indicates RSCNs generated by Nx_Ports. 'fromBoth' indicates RSCNs generated by Fabric Controller and Nx_Ports." ::= { rscnScrEntry 2 } -- Statistics rscnScrTotalRejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of SCRs rejected across all VSANs by the local switch." ::= { rscnStats 1 } rscnRscnReqTotalRejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of RSCN requests rejected across all VSANs by the local switch." ::= { rscnStats 2 } rscnSwRscnReqTotalRejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of SW_RSCN requests rejected across all VSANs by the local switch." ::= { rscnStats 3 } rscnStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF RscnStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The statistics related to the RSCN module. The statistics are maintained per VSAN." ::= { rscnStats 4 } rscnStatsEntry OBJECT-TYPE SYNTAX RscnStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in this table." INDEX { vsanIndex } ::= { rscnStatsTable 1 } RscnStatsEntry ::= SEQUENCE { rscnRxScrs Counter32, rscnRxRscns Counter32, rscnTxRscns Counter32, rscnRxSwRscns Counter32, rscnTxSwRscns Counter32, rscnScrRej Counter32, rscnRscnReqRej Counter32, rscnSwRscnReqRej Counter32 } rscnRxScrs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of SCRs received from Nx_Ports on this VSAN." ::= { rscnStatsEntry 1 } rscnRxRscns OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RSCNs from Nx_Ports received on this VSAN." ::= { rscnStatsEntry 2 } rscnTxRscns OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of RSCNs transmitted on this VSAN." ::= { rscnStatsEntry 3 } rscnRxSwRscns OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Inter-Switch Registered State Change Notifications (SW_RSCN) received on this VSAN from other switches." ::= { rscnStatsEntry 4 } rscnTxSwRscns OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Inter-Switch Registered State Change Notifications (SW_RSCN) transmitted on this VSAN to other switches." ::= { rscnStatsEntry 5 } rscnScrRej OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of SCR rejected on this VSAN." ::= { rscnStatsEntry 6 } rscnRscnReqRej OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RSCN requests rejected on this VSAN." ::= { rscnStatsEntry 7 } rscnSwRscnReqRej OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of SW_RSCN requests rejected on this VSAN." ::= { rscnStatsEntry 8 } -- Notification Information rscnIlsRejReasonCode OBJECT-TYPE SYNTAX FcGs3RejectReasonCode MAX-ACCESS read-only STATUS current DESCRIPTION "The reason code corresponding to an ILS request rejection. This object contains the reason code corresponding to the most recent SCR or RSCN request rejection by the RSCN module." ::= { rscnInformation 1 } rscnElsRejReasonCode OBJECT-TYPE SYNTAX FcGs3RejectReasonCode MAX-ACCESS read-only STATUS current DESCRIPTION "The reason code corresponding to an ELS request rejection. This object contains the reason code corresponding the most recent SW_RSCN request rejection by the RSCN module." ::= { rscnInformation 2 } -- Notification control objects rscnIlsRejectReqNotifyEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies if the RSCN module should generate 'rscnIlsRejectReqNotify' notifications. If value of this object is 'true', then the notification is generated when a SW_RSCN request is rejected. If it is 'false', the notification is not generated." DEFVAL { false } ::= { rscnConfiguration 3 } rscnElsRejectReqNotifyEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies if the RSCN module should generate 'rscnElsRejectReqNotify' notifications. If value of this object is 'true', then the notification is generated when a SCR or RSCN request is rejected. If it is 'false', the notification is not generated." DEFVAL { false } ::= { rscnConfiguration 4 } rscnNotifyFcId OBJECT-TYPE SYNTAX FcAddressId MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The FC-ID of an Nx_Port. This object is to be used in the notifications: rscnElsRejectReqNotify, rscnIlsRejectReqNotify, rscnElsRxRejectReqNotify and rscnIlsRxRejectReqNotify. This object is defined since the rscnScrFcId object in the rscnScrTable is not-accessible." ::= { rscnConfiguration 5 } rscnMultiPidTable OBJECT-TYPE SYNTAX SEQUENCE OF RscnMultiPidEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the configuration information for multi-pid option for all VSANs on the local device." ::= { rscnConfiguration 6 } rscnMultiPidEntry OBJECT-TYPE SYNTAX RscnMultiPidEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in this table." INDEX { vsanIndex } ::= { rscnMultiPidTable 1 } RscnMultiPidEntry ::= SEQUENCE { rscnMultiPidEnable TruthValue } rscnMultiPidEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether the multi-pid option is enabled on this VSAN. If this object is set to 'true', then the multi-pid option is enabled. If this object is set to 'false, then the multi-pid option is disabled. If the multi-pid option is enabled, then RSCNs generated to the registered Nx ports may contain more than one affected port ID. By enabling this option, the number of RSCNs generated can be reduced." DEFVAL { false } ::= { rscnMultiPidEntry 1 } rscnEventTovTable OBJECT-TYPE SYNTAX SEQUENCE OF RscnEventTovEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the configuration information for Event Time Out Value option for all VSANs on the local device. The Event TOV value is used to send the coalesced RSCNs to the registered user." ::= { rscnConfiguration 7 } rscnEventTovEntry OBJECT-TYPE SYNTAX RscnEventTovEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in this table represents the Event Time out value on a VSAN." INDEX { vsanIndex } ::= { rscnEventTovTable 1 } RscnEventTovEntry ::= SEQUENCE { rscnEventTov Unsigned32 } rscnEventTov OBJECT-TYPE SYNTAX Unsigned32 (0..2000) UNITS "milli-secs" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the event time-out value configured for the VSAN. This timeout value corresponds to the coalescing timeout. This object is used to merge a number of RSCNs into a single frame and send them out when timer expires. The value of zero indicates that frames will not be coalesced." DEFVAL { 2000 } ::= { rscnEventTovEntry 1 } rscnIlsRxRejectReqNotifyEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies if the RSCN module should generate 'rscnIlsRxRejectReqNotify' notifications. If value of this object is 'true', then the notification is generated when a SW_RSCN that is rejected by another device is received on the local device. If it is 'false', the notification is not generated." DEFVAL { false } ::= { rscnConfiguration 8 } rscnElsRxRejectReqNotifyEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies if the RSCN module should generate 'rscnElsRxRejectReqNotify' notifications. If value of this object is 'true', then the notification is generated when a RSCN request that is rejected by another device is received on the local device. If it is 'false', the notification is not generated." DEFVAL { false } ::= { rscnConfiguration 9 } -- Notifications rscnElsRejectReqNotify NOTIFICATION-TYPE OBJECTS { rscnElsRejReasonCode, rscnNotifyFcId } STATUS current DESCRIPTION "This notification is generated by the RSCN module on this switch whenever it rejects a SCR or RSCN request. The rscnScrFcId object indicates the FC-ID of the sender of the request that was rejected." ::= { rscnNotifications 1 } rscnIlsRejectReqNotify NOTIFICATION-TYPE OBJECTS { rscnIlsRejReasonCode, rscnNotifyFcId } STATUS current DESCRIPTION "This notification is generated by the RSCN module on this switch whenever it rejects a SW_RSCN request. The rscnScrFcId object contains the FC-ID of the sender of the request that was rejected." ::= { rscnNotifications 2 } rscnElsRxRejectReqNotify NOTIFICATION-TYPE OBJECTS { rscnElsRejReasonCode, rscnNotifyFcId } STATUS current DESCRIPTION "This notification is generated by the RSCN module on this switch whenever it receives a rejected RSCN request. The rscnScrFcId object indicates the FC-ID of the sender where the request was rejected." ::= { rscnNotifications 3 } rscnIlsRxRejectReqNotify NOTIFICATION-TYPE OBJECTS { rscnIlsRejReasonCode, rscnNotifyFcId } STATUS current DESCRIPTION "This notification is generated by the RSCN module on this switch whenever it receives a rejected SW_RSCN request. The rscnScrFcId object contains the FC-ID of the sender where the request was rejected." ::= { rscnNotifications 4 } -- Conformance rscnMIBCompliances OBJECT IDENTIFIER ::= { rscnMIBConformance 1 } rscnMIBGroups OBJECT IDENTIFIER ::= { rscnMIBConformance 2 } rscnMIBCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for entities which implement RSCN feature." MODULE -- this module MANDATORY-GROUPS { rscnConfigGroup, rscnStatsGroup, rscnNotifyControlGroup, rscnNotifyGroup } ::= { rscnMIBCompliances 1 } rscnMIBComplianceRev1 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for entities which implement RSCN feature." MODULE -- this module MANDATORY-GROUPS { rscnConfigGroupRev1, rscnStatsGroup, rscnNotifyControlGroup, rscnNotifyGroup } ::= { rscnMIBCompliances 2 } rscnMIBComplianceRev2 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for entities which implement RSCN feature." MODULE -- this module MANDATORY-GROUPS { rscnConfigGroupRev1, rscnStatsGroup, rscnNotifyControlGroup, rscnNotifyGroup, rscnConfigGroupRev1Sup1 } ::= { rscnMIBCompliances 3 } rscnMIBComplianceRev3 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement RSCN feature." MODULE -- this module MANDATORY-GROUPS { rscnConfigGroupRev1, rscnStatsGroup, rscnNotifyControlGroup, rscnNotifyGroup, rscnConfigGroupRev1Sup1, rscnRejectNotifyGroup, rscnNotifyControlGroupSup1 } ::= { rscnMIBCompliances 4 } -- Units of conformance rscnConfigGroup OBJECT-GROUP OBJECTS { rscnScrNumber, rscnScrRegType, rscnNotifyFcId } STATUS deprecated DESCRIPTION "A collection of objects for configuring and displaying SCR entries." ::= { rscnMIBGroups 1 } rscnStatsGroup OBJECT-GROUP OBJECTS { rscnScrTotalRejects, rscnRscnReqTotalRejects, rscnSwRscnReqTotalRejects, rscnRxScrs, rscnRxRscns, rscnTxRscns, rscnRxSwRscns, rscnTxSwRscns, rscnScrRej, rscnRscnReqRej, rscnSwRscnReqRej } STATUS current DESCRIPTION "A collection of objects for displaying RSCN statistics." ::= { rscnMIBGroups 2 } rscnNotifyControlGroup OBJECT-GROUP OBJECTS { rscnIlsRejReasonCode, rscnElsRejReasonCode, rscnIlsRejectReqNotifyEnable, rscnElsRejectReqNotifyEnable } STATUS current DESCRIPTION "A collection of notification control and notification information objects." ::= { rscnMIBGroups 3 } rscnNotifyGroup NOTIFICATION-GROUP NOTIFICATIONS { rscnIlsRejectReqNotify, rscnElsRejectReqNotify } STATUS current DESCRIPTION "A collection of notifications for monitoring ILS and ELS request rejection by the RSCN module." ::= { rscnMIBGroups 4 } rscnConfigGroupRev1 OBJECT-GROUP OBJECTS { rscnScrNumber, rscnScrRegType, rscnNotifyFcId, rscnMultiPidEnable } STATUS current DESCRIPTION "A collection of objects for configuring and displaying SCR entries and multi-pid option." ::= { rscnMIBGroups 5 } rscnConfigGroupRev1Sup1 OBJECT-GROUP OBJECTS { rscnEventTov } STATUS current DESCRIPTION "A collection of object(s) for configuring the Event time out option." ::= { rscnMIBGroups 6 } rscnRejectNotifyGroup NOTIFICATION-GROUP NOTIFICATIONS { rscnIlsRxRejectReqNotify, rscnElsRxRejectReqNotify } STATUS current DESCRIPTION "A collection of notifications for monitoring ILS and ELS request rejection by other switches/ devices." ::= { rscnMIBGroups 7 } rscnNotifyControlGroupSup1 OBJECT-GROUP OBJECTS { rscnIlsRxRejectReqNotifyEnable, rscnElsRxRejectReqNotifyEnable } STATUS current DESCRIPTION "A collection of notification control objects." ::= { rscnMIBGroups 8 } END