-- ***************************************************************** -- CISCO-PROXY-CONTROL-MIB.my: Proxy Control MIB file -- -- November 1999 Chris White -- -- Copyright (c) 1999, 2000-2005, 2006, 2009 by cisco Systems Inc. -- All rights reserved. -- ***************************************************************** CISCO-PROXY-CONTROL-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, IpAddress, Integer32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF TEXTUAL-CONVENTION FROM SNMPv2-TC callActiveSetupTime, callActiveIndex, AbsoluteCounter32 FROM DIAL-CONTROL-MIB CvcGUid FROM CISCO-VOICE-COMMON-DIAL-CONTROL-MIB cCallHistoryIndex FROM CISCO-DIAL-CONTROL-MIB ciscoExperiment FROM CISCO-SMI; ciscoProxyControlMIB MODULE-IDENTITY LAST-UPDATED "200902110000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems, Inc. Customer Service Postal: 170 W. Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-voice@cisco.com" DESCRIPTION "This MIB module enhances the IETF Dial Control MIB (RFC2128) by providing Proxy management information. *** ABBREVIATIONS, ACRONYMS AND SYMBOLS *** GSM - Global System for Mobile Communication AMR-NB - Adaptive Multi Rate - Narrow Band iLBC - internet Low Bitrate Codec iSAC - internet Speech Audio Codec" REVISION "200902110000Z" DESCRIPTION "[1] Added acronyms for iSAC codecs [2] Added iSAC enum to CProxyAudioCodec textual convention. [3] Added REFERENCE clause to CProxyAudioCodec textual convention for iSAC codec." REVISION "200603120000Z" DESCRIPTION "[1] Added acronyms for GSM AMR-NB and iLBC codecs [2] Added iLBC enum to CProxyAudioCodec textual convention. [3] Added REFERENCE clause to CProxyAudioCodec textual convention for GSM AMR-NB and iLBC codecs." REVISION "200503060000Z" DESCRIPTION "Added gsmAmrNb enum to CProxyAudioCodec textual convention." REVISION "200002040000Z" DESCRIPTION "First release of this MIB." ::= { ciscoExperiment 57 } -- Voice Proxy Dial Control MIB objects definitions ciscoProxyControlMIBObjects OBJECT IDENTIFIER ::= { ciscoProxyControlMIB 1 } -- The Proxy Control MIB consists of the following groups -- [1] Proxy Control Call Active Group (cProxyCallActive) -- [2] Proxy Control Call History Group (cProxyCallHistory) cProxyCallActive OBJECT IDENTIFIER ::= { ciscoProxyControlMIBObjects 1 } cProxyCallHistory OBJECT IDENTIFIER ::= { ciscoProxyControlMIBObjects 2 } -- Textual Conventions CProxyEndptType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A tag to identify the type of end point that the Proxy is connected to." SYNTAX INTEGER { other(0), -- none of the following proxy(1), -- another h323 proxy gateway(2) -- h323 gateway } CProxyAudioCodec ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A tag to identify the type of encoding used to compress the voice data of the call. iLBC - iILBC 13330 or 15200 bps iSAC - iSAC 10 to 32 kbps" REFERENCE "[1] RFC 3267: For introduction about GSM AMR-NB codec, section 3.1 [2] RFC 3952: For introduction about iLBC codec, section 2 [3] iSAC Codec Description Document from GIPS" SYNTAX INTEGER { other(0), nonStandard(1), g711Alawr64k(2), g711Alawr56k(3), g711Ulawr64k(4), g711Ulawr56k(5), g722r64k(6), g722r56k(7), g722r48k(8), g7231(9), g728(10), g729(11), g729AnnexA(12), is11172(13), is13818(14), g729AnnexB(15), g729AnnexAB(16), g729AnnexC(17), gsmFullRate(18), gsmHalfRate(19), gsmEnhancedFullRate(20), gsmAmrNb(21), iLBC(22), iSAC(23) } CProxyVideoCodec ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A tag to identify the type of encoding used to compress the video data of the call." SYNTAX INTEGER { other(0), nonStandard(1), h261(2), h262(3), h263(4), is11172(5) } -- ********************************************************************** -- Proxy Dial Control Call Active Group -- ********************************************************************** -- -- Proxy Call Active Table cProxyCallActiveTable OBJECT-TYPE SYNTAX SEQUENCE OF CProxyCallActiveEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is the Proxy extension to the call Active table of IETF Dial Control MIB. It contains Proxy call leg information about specific proxied calls." REFERENCE "IETF Dial Control MIB (RFC2128)" ::= { cProxyCallActive 1 } cProxyCallActiveEntry OBJECT-TYPE SYNTAX CProxyCallActiveEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The information regarding a single proxied call leg. An entry of this table is created when its associated call Active entry in the IETF Dial Control MIB is created and the call Active entry contains information for the call establishment to the peer on the data network. This entry is deleted when its associated Call Active entry in the IETF Dial Control MIB is deleted." INDEX { callActiveSetupTime, callActiveIndex } ::= { cProxyCallActiveTable 1 } CProxyCallActiveEntry ::= SEQUENCE { cProxyCallActiveConnectionId CvcGUid, cProxyCallActiveRemoteIPAddress IpAddress, cProxyCallActiveAudioUDPPort INTEGER, cProxyCallActiveVideoUDPPort INTEGER, cProxyCallActiveT120TCPPort1 INTEGER, cProxyCallActiveT120TCPPort2 INTEGER, cProxyCallActiveT120TCPPort3 INTEGER, cProxyCallActiveT120TCPPort4 INTEGER, cProxyCallActiveEndpointType CProxyEndptType, cProxyCallActiveEndpointVendor INTEGER, cProxyCallActiveRequestBandwidth Integer32, cProxyCallActiveActualBandwidth Integer32, cProxyCallActiveAudioCoderRate CProxyAudioCodec, cProxyCallActiveVideoCoderRate CProxyVideoCodec, cProxyCallActiveRxAudioPackets AbsoluteCounter32, cProxyCallActiveRxAudioBytes AbsoluteCounter32, cProxyCallActiveTxAudioPackets AbsoluteCounter32, cProxyCallActiveTxAudioBytes AbsoluteCounter32, cProxyCallActiveRxVideoPackets AbsoluteCounter32, cProxyCallActiveRxVideoBytes AbsoluteCounter32, cProxyCallActiveTxVideoPackets AbsoluteCounter32, cProxyCallActiveTxVideoBytes AbsoluteCounter32, cProxyCallActiveRxT120Packets AbsoluteCounter32, cProxyCallActiveRxT120Bytes AbsoluteCounter32, cProxyCallActiveTxT120Packets AbsoluteCounter32, cProxyCallActiveTxT120Bytes AbsoluteCounter32 } cProxyCallActiveConnectionId OBJECT-TYPE SYNTAX CvcGUid MAX-ACCESS read-only STATUS current DESCRIPTION "The global call identifier for the Proxy call." ::= { cProxyCallActiveEntry 1 } cProxyCallActiveRemoteIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Remote system IP address for the call." ::= { cProxyCallActiveEntry 2 } cProxyCallActiveAudioUDPPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Remote system UDP listener port to which to transmit voice packets for the call. A value of zero indicates that no port was used." ::= { cProxyCallActiveEntry 3 } cProxyCallActiveVideoUDPPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Remote system UDP listener port to which to transmit video packets for the call. A value of zero indicates that no port was used." ::= { cProxyCallActiveEntry 4 } cProxyCallActiveT120TCPPort1 OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "First remote system UDP listener port to which to transmit T120 packets for the call. A value of zero indicates that no port was used." ::= { cProxyCallActiveEntry 5 } cProxyCallActiveT120TCPPort2 OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Second remote system UDP listener port to which to transmit T120 packets for the call. A value of zero indicates that no port was used." ::= { cProxyCallActiveEntry 6 } cProxyCallActiveT120TCPPort3 OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Third remote system UDP listener port to which to transmit T120 packets for the call. A value of zero indicates that no port was used." ::= { cProxyCallActiveEntry 7 } cProxyCallActiveT120TCPPort4 OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Fourth remote system UDP listener port to which to transmit T120 packets for the call. A value of zero indicates that no port was used." ::= { cProxyCallActiveEntry 8 } cProxyCallActiveEndpointType OBJECT-TYPE SYNTAX CProxyEndptType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of end point this proxy call leg is connected to." ::= { cProxyCallActiveEntry 9 } cProxyCallActiveEndpointVendor OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The H225 Manufacturers code for this endpoint. Zero indicates unknown vendor." ::= { cProxyCallActiveEntry 10 } cProxyCallActiveRequestBandwidth OBJECT-TYPE SYNTAX Integer32 (0..10000000) UNITS "kilobits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "The requested bandwidth for this proxied call leg." ::= { cProxyCallActiveEntry 11 } cProxyCallActiveActualBandwidth OBJECT-TYPE SYNTAX Integer32 (0..10000000) UNITS "kilobits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "The actual bandwidth used by the proxied call." ::= { cProxyCallActiveEntry 12 } cProxyCallActiveAudioCoderRate OBJECT-TYPE SYNTAX CProxyAudioCodec MAX-ACCESS read-only STATUS current DESCRIPTION "The negotiated coder rate. It specifies the transmit rate of audio compression to its associated call leg for the call." ::= { cProxyCallActiveEntry 13 } cProxyCallActiveVideoCoderRate OBJECT-TYPE SYNTAX CProxyVideoCodec MAX-ACCESS read-only STATUS current DESCRIPTION "The negotiated coder rate. It specifies the transmit rate of video compression to its associated call leg for the call." ::= { cProxyCallActiveEntry 14 } cProxyCallActiveRxAudioPackets OBJECT-TYPE SYNTAX AbsoluteCounter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of audio packets received from the remote end for this call." ::= { cProxyCallActiveEntry 15 } cProxyCallActiveRxAudioBytes OBJECT-TYPE SYNTAX AbsoluteCounter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of audio bytes received from the remote end for this call." ::= { cProxyCallActiveEntry 16 } cProxyCallActiveTxAudioPackets OBJECT-TYPE SYNTAX AbsoluteCounter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of audio packets transmitted to the remote end for this call." ::= { cProxyCallActiveEntry 17 } cProxyCallActiveTxAudioBytes OBJECT-TYPE SYNTAX AbsoluteCounter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of audio bytes transmitted to the remote end for this call." ::= { cProxyCallActiveEntry 18 } cProxyCallActiveRxVideoPackets OBJECT-TYPE SYNTAX AbsoluteCounter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of video packets received from the remote end for this call." ::= { cProxyCallActiveEntry 19 } cProxyCallActiveRxVideoBytes OBJECT-TYPE SYNTAX AbsoluteCounter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of video bytes received from the remote end for this call." ::= { cProxyCallActiveEntry 20 } cProxyCallActiveTxVideoPackets OBJECT-TYPE SYNTAX AbsoluteCounter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of video packets transmitted to the remote end for this call." ::= { cProxyCallActiveEntry 21 } cProxyCallActiveTxVideoBytes OBJECT-TYPE SYNTAX AbsoluteCounter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of video bytes transmitted to the remote end for this call." ::= { cProxyCallActiveEntry 22 } cProxyCallActiveRxT120Packets OBJECT-TYPE SYNTAX AbsoluteCounter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of T120 data packets received from the remote end for this call." ::= { cProxyCallActiveEntry 23 } cProxyCallActiveRxT120Bytes OBJECT-TYPE SYNTAX AbsoluteCounter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of T120 data bytes received from the remote end of this call." ::= { cProxyCallActiveEntry 24 } cProxyCallActiveTxT120Packets OBJECT-TYPE SYNTAX AbsoluteCounter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of T120 data packets transmitted to the remote end for this call." ::= { cProxyCallActiveEntry 25 } cProxyCallActiveTxT120Bytes OBJECT-TYPE SYNTAX AbsoluteCounter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of T120 data bytes transmitted to the remote end of this call." ::= { cProxyCallActiveEntry 26 } -- ********************************************************************** -- Proxy Dial Control Call History Group -- ********************************************************************** -- -- Proxy Call History Table cProxyCallHistoryTable OBJECT-TYPE SYNTAX SEQUENCE OF CProxyCallHistoryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is the Proxy extension to the History call table of IETF Dial Control MIB. It contains PROXY call leg information about proxied call." REFERENCE "IETF Dial Control MIB (RFC2128)" ::= { cProxyCallHistory 1 } cProxyCallHistoryEntry OBJECT-TYPE SYNTAX CProxyCallHistoryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The information regarding a single proxied call leg. An entry of this table is created when its associated call History entry in the IETF Dial Control MIB is created. The call History entry contains information for the call establishment to the peer on the data network backbone via a voice over PROXY peer. The entry is deleted when its associated call History entry in the IETF Dial Control MIB is deleted." INDEX { cCallHistoryIndex } ::= { cProxyCallHistoryTable 1 } CProxyCallHistoryEntry ::= SEQUENCE { cProxyCallHistoryConnectionId CvcGUid, cProxyCallHistoryRemoteIPAddress IpAddress, cProxyCallHistoryAudioUDPPort INTEGER, cProxyCallHistoryVideoUDPPort INTEGER, cProxyCallHistoryT120TCPPort1 INTEGER, cProxyCallHistoryT120TCPPort2 INTEGER, cProxyCallHistoryT120TCPPort3 INTEGER, cProxyCallHistoryT120TCPPort4 INTEGER, cProxyCallHistoryEndpointType CProxyEndptType, cProxyCallHistoryEndpointVendor INTEGER, cProxyCallHistoryRequestBandwidth Integer32, cProxyCallHistoryActualBandwidth Integer32, cProxyCallHistoryAudioCoderRate CProxyAudioCodec, cProxyCallHistoryVideoCoderRate CProxyVideoCodec, cProxyCallHistoryRxAudioPackets AbsoluteCounter32, cProxyCallHistoryRxAudioBytes AbsoluteCounter32, cProxyCallHistoryTxAudioPackets AbsoluteCounter32, cProxyCallHistoryTxAudioBytes AbsoluteCounter32, cProxyCallHistoryRxVideoPackets AbsoluteCounter32, cProxyCallHistoryRxVideoBytes AbsoluteCounter32, cProxyCallHistoryTxVideoPackets AbsoluteCounter32, cProxyCallHistoryTxVideoBytes AbsoluteCounter32, cProxyCallHistoryRxT120Packets AbsoluteCounter32, cProxyCallHistoryRxT120Bytes AbsoluteCounter32, cProxyCallHistoryTxT120Packets AbsoluteCounter32, cProxyCallHistoryTxT120Bytes AbsoluteCounter32 } cProxyCallHistoryConnectionId OBJECT-TYPE SYNTAX CvcGUid MAX-ACCESS read-only STATUS current DESCRIPTION "The global call identifier for the Proxy call." ::= { cProxyCallHistoryEntry 1 } cProxyCallHistoryRemoteIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Remote system IP address for the call." ::= { cProxyCallHistoryEntry 2 } cProxyCallHistoryAudioUDPPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Remote system UDP listener port to which to transmit voice packets for the call. A value of zero indicates that no port was used." ::= { cProxyCallHistoryEntry 3 } cProxyCallHistoryVideoUDPPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Remote system UDP listener port to which to transmit video packets for the call. A value of zero indicates that no port was used." ::= { cProxyCallHistoryEntry 4 } cProxyCallHistoryT120TCPPort1 OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "First remote system UDP listener port to which to transmit T120 packets for the call. A value of zero indicates that no port was used." ::= { cProxyCallHistoryEntry 5 } cProxyCallHistoryT120TCPPort2 OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Second remote system UDP listener port to which to transmit T120 packets for the call. A value of zero indicates that no port was used." ::= { cProxyCallHistoryEntry 6 } cProxyCallHistoryT120TCPPort3 OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Third remote system UDP listener port to which to transmit T120 packets for the call. A value of zero indicates that no port was used." ::= { cProxyCallHistoryEntry 7 } cProxyCallHistoryT120TCPPort4 OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Fourth remote system UDP listener port to which to transmit T120 packets for the call. A value of zero indicates that no port was used." ::= { cProxyCallHistoryEntry 8 } cProxyCallHistoryEndpointType OBJECT-TYPE SYNTAX CProxyEndptType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of end point this proxy call leg is connected to." ::= { cProxyCallHistoryEntry 9 } cProxyCallHistoryEndpointVendor OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The H225 Manufacturers code for this endpoint. Zero indicates unknown vendor." ::= { cProxyCallHistoryEntry 10 } cProxyCallHistoryRequestBandwidth OBJECT-TYPE SYNTAX Integer32 (0..10000000) UNITS "kilobits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "The requested bandwidth for this proxied call leg." ::= { cProxyCallHistoryEntry 11 } cProxyCallHistoryActualBandwidth OBJECT-TYPE SYNTAX Integer32 (0..10000000) UNITS "kilobits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "The actual bandwidth used by the proxied call." ::= { cProxyCallHistoryEntry 12 } cProxyCallHistoryAudioCoderRate OBJECT-TYPE SYNTAX CProxyAudioCodec MAX-ACCESS read-only STATUS current DESCRIPTION "The negotiated coder rate. It specifies the transmit rate of audio compression to its associated call leg for the call." ::= { cProxyCallHistoryEntry 13 } cProxyCallHistoryVideoCoderRate OBJECT-TYPE SYNTAX CProxyVideoCodec MAX-ACCESS read-only STATUS current DESCRIPTION "The negotiated coder rate. It specifies the transmit rate of video compression to its associated call leg for the call." ::= { cProxyCallHistoryEntry 14 } cProxyCallHistoryRxAudioPackets OBJECT-TYPE SYNTAX AbsoluteCounter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of audio packets received from the remote end for this call." ::= { cProxyCallHistoryEntry 15 } cProxyCallHistoryRxAudioBytes OBJECT-TYPE SYNTAX AbsoluteCounter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of audio bytes received from the remote end for this call." ::= { cProxyCallHistoryEntry 16 } cProxyCallHistoryTxAudioPackets OBJECT-TYPE SYNTAX AbsoluteCounter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of audio packets transmitted to the remote end for this call." ::= { cProxyCallHistoryEntry 17 } cProxyCallHistoryTxAudioBytes OBJECT-TYPE SYNTAX AbsoluteCounter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of audio bytes transmitted to the remote end for this call." ::= { cProxyCallHistoryEntry 18 } cProxyCallHistoryRxVideoPackets OBJECT-TYPE SYNTAX AbsoluteCounter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of video packets received from the remote end for this call." ::= { cProxyCallHistoryEntry 19 } cProxyCallHistoryRxVideoBytes OBJECT-TYPE SYNTAX AbsoluteCounter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of video bytes received from the remote end for this call." ::= { cProxyCallHistoryEntry 20 } cProxyCallHistoryTxVideoPackets OBJECT-TYPE SYNTAX AbsoluteCounter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of video packets transmitted to the remote end for this call." ::= { cProxyCallHistoryEntry 21 } cProxyCallHistoryTxVideoBytes OBJECT-TYPE SYNTAX AbsoluteCounter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of video bytes transmitted to the remote end for this call." ::= { cProxyCallHistoryEntry 22 } cProxyCallHistoryRxT120Packets OBJECT-TYPE SYNTAX AbsoluteCounter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of T120 data packets received from the remote end for this call." ::= { cProxyCallHistoryEntry 23 } cProxyCallHistoryRxT120Bytes OBJECT-TYPE SYNTAX AbsoluteCounter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of T120 data bytes received from the remote end for this call." ::= { cProxyCallHistoryEntry 24 } cProxyCallHistoryTxT120Packets OBJECT-TYPE SYNTAX AbsoluteCounter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of T120 data packets transmitted to the remote end for this call." ::= { cProxyCallHistoryEntry 25 } cProxyCallHistoryTxT120Bytes OBJECT-TYPE SYNTAX AbsoluteCounter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of T120 data bytes transmitted to the remote end for this call." ::= { cProxyCallHistoryEntry 26 } -- Notifications ciscoProxyControlMIBNotificationPrefix OBJECT IDENTIFIER ::= { ciscoProxyControlMIB 2 } ciscoProxyControlMIBNotifications OBJECT IDENTIFIER ::= { ciscoProxyControlMIBNotificationPrefix 0 } -- Conformancy, Compliance and Group Objects ciscoProxyControlMIBConformance OBJECT IDENTIFIER ::= { ciscoProxyControlMIB 3 } ciscoProxyControlMIBCompliances OBJECT IDENTIFIER ::= { ciscoProxyControlMIBConformance 1 } ciscoProxyControlMIBGroups OBJECT IDENTIFIER ::= { ciscoProxyControlMIBConformance 2 } -- compliance statements ciscoProxyControlMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement the CISCO PROXY CONTROL MIB" MODULE -- this module MANDATORY-GROUPS { cProxyCallActiveGroup, cProxyCallHistoryGroup } ::= { ciscoProxyControlMIBCompliances 1 } -- units of conformance cProxyCallActiveGroup OBJECT-GROUP OBJECTS { cProxyCallActiveConnectionId, cProxyCallActiveRemoteIPAddress, cProxyCallActiveAudioUDPPort, cProxyCallActiveVideoUDPPort, cProxyCallActiveT120TCPPort1, cProxyCallActiveT120TCPPort2, cProxyCallActiveT120TCPPort3, cProxyCallActiveT120TCPPort4, cProxyCallActiveEndpointType, cProxyCallActiveEndpointVendor, cProxyCallActiveRequestBandwidth, cProxyCallActiveActualBandwidth, cProxyCallActiveAudioCoderRate, cProxyCallActiveVideoCoderRate, cProxyCallActiveRxAudioPackets, cProxyCallActiveRxAudioBytes, cProxyCallActiveTxAudioPackets, cProxyCallActiveTxAudioBytes, cProxyCallActiveRxVideoPackets, cProxyCallActiveRxVideoBytes, cProxyCallActiveTxVideoPackets, cProxyCallActiveTxVideoBytes, cProxyCallActiveRxT120Packets, cProxyCallActiveRxT120Bytes, cProxyCallActiveTxT120Packets, cProxyCallActiveTxT120Bytes } STATUS current DESCRIPTION "A collection of objects providing the PROXY Call Active entry capability." ::= { ciscoProxyControlMIBGroups 1 } cProxyCallHistoryGroup OBJECT-GROUP OBJECTS { cProxyCallHistoryConnectionId, cProxyCallHistoryRemoteIPAddress, cProxyCallHistoryAudioUDPPort, cProxyCallHistoryVideoUDPPort, cProxyCallHistoryT120TCPPort1, cProxyCallHistoryT120TCPPort2, cProxyCallHistoryT120TCPPort3, cProxyCallHistoryT120TCPPort4, cProxyCallHistoryEndpointType, cProxyCallHistoryEndpointVendor, cProxyCallHistoryRequestBandwidth, cProxyCallHistoryActualBandwidth, cProxyCallHistoryAudioCoderRate, cProxyCallHistoryVideoCoderRate, cProxyCallHistoryRxAudioPackets, cProxyCallHistoryRxAudioBytes, cProxyCallHistoryTxAudioPackets, cProxyCallHistoryTxAudioBytes, cProxyCallHistoryRxVideoPackets, cProxyCallHistoryRxVideoBytes, cProxyCallHistoryTxVideoPackets, cProxyCallHistoryTxVideoBytes, cProxyCallHistoryRxT120Packets, cProxyCallHistoryRxT120Bytes, cProxyCallHistoryTxT120Packets, cProxyCallHistoryTxT120Bytes } STATUS current DESCRIPTION "A collection of objects providing the PROXY Call Active entry capability." ::= { ciscoProxyControlMIBGroups 2 } END