-- ********************************************************************* -- CISCO-PROP-ATM-IF-MIB: This mib is for propAtm port interface -- -- April 2002, Yizhong Shen -- -- Copyright (c) 2002 by cisco Systems, Inc. -- All rights reserved. -- ********************************************************************* CISCO-PROP-ATM-IF-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Counter32, Counter64, Unsigned32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF ifIndex FROM IF-MIB ciscoMgmt FROM CISCO-SMI; ciscoPropAtmIfMIB MODULE-IDENTITY LAST-UPDATED "200212040000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-voice-gateway@cisco.com" DESCRIPTION "This MIB is designed for Propietary ATM (propAtm) interfaces. The propAtm interfaces are identified in the ifTable entries with ifType 197 (as defined in IANAifType-MIB). This interface is a switch virtual interface which does not have any physical connector(jack). " REVISION "200212040000Z" DESCRIPTION "Initial version of this MIB module." ::= {ciscoMgmt 319 } ciscoPropAtmIfMIBNotifs OBJECT IDENTIFIER ::= { ciscoPropAtmIfMIB 0 } ciscoPropAtmIfMIBObjects OBJECT IDENTIFIER ::= { ciscoPropAtmIfMIB 1} cpAtmIfConfig OBJECT IDENTIFIER ::= { ciscoPropAtmIfMIBObjects 1} cpAtmIfVirtualPortStats OBJECT IDENTIFIER ::= { ciscoPropAtmIfMIBObjects 2} -- ********************************************************************* -- cpAtmIfConfigTable -- ********************************************************************* cpAtmIfConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF CpAtmIfConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used to configure propAtm interfaces. Each entry in this table has a corresponding ifTable entry with ifType propAtm(197). The ifIndex value of that associated ifTable entry is used to index this this table. The entry of this table is added after its associated ifEntry is added in the ifTable of IF-MIB. It is impossible to add/delete entry to/from this table. " ::= { cpAtmIfConfig 1 } cpAtmIfConfigEntry OBJECT-TYPE SYNTAX CpAtmIfConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the cpAtmIfConfigTable table for each propAtm port interface. ." INDEX { ifIndex } ::= { cpAtmIfConfigTable 1 } CpAtmIfConfigEntry ::= SEQUENCE { cpAtmIfMaxBandwidth Unsigned32 } cpAtmIfMaxBandwidth OBJECT-TYPE SYNTAX Unsigned32(0..4294967295) UNITS "cells-per-second" MAX-ACCESS read-write STATUS current DESCRIPTION "The propATM interface's maximum cell rate. " DEFVAL{ 7000000 } ::= { cpAtmIfConfigEntry 1 } -- ********************************************************************* -- cpAtmIfStatsEgressTable -- ********************************************************************* cpAtmIfStatsEgressTable OBJECT-TYPE SYNTAX SEQUENCE OF CpAtmIfStatsEgressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table reflects real-time statistics associated with each of propAtm interfaces on the egress side. Ingress terminology is used for the cells that are generated by the voice gateway on the TDM side and are going toward the ATM switch. Egress terminology means the cells that are coming from the ATM switch into the TDM side. This table contains statistics from this egress point of view. " ::= { cpAtmIfVirtualPortStats 1 } cpAtmIfStatsEgressEntry OBJECT-TYPE SYNTAX CpAtmIfStatsEgressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the cpAtmIfStatsEgressTable table for each propAtm port interface. CLP-0 means Cell Loss Priority = 0, CLP-1 means Cell Loss Priority = 1. " INDEX { ifIndex } ::= { cpAtmIfStatsEgressTable 1 } CpAtmIfStatsEgressEntry ::= SEQUENCE { cpAtmIfEgrRcvClp0Cells Counter32, cpAtmIfEgrRcvClp1Cells Counter32, cpAtmIfEgrClp0DiscCells Counter32, cpAtmIfEgrClp1DiscCells Counter32, cpAtmIfEgrRcvOAMCells Counter32, cpAtmIfEgrRcvEFCICells Counter32, cpAtmIfHCEgrRcvClp0Cells Counter64, cpAtmIfHCEgrRcvClp1Cells Counter64, cpAtmIfHCEgrClp0DiscCells Counter64, cpAtmIfHCEgrClp1DiscCells Counter64, cpAtmIfHCEgrRcvOAMCells Counter64, cpAtmIfHCEgrRcvEFCICells Counter64 } cpAtmIfEgrRcvClp0Cells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of CLP-0 cells received from switch at the traffic management and policing device. " ::= { cpAtmIfStatsEgressEntry 1 } cpAtmIfEgrRcvClp1Cells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of CLP-1 cells received from switch at the traffic management and policing device. " ::= { cpAtmIfStatsEgressEntry 2 } cpAtmIfEgrClp0DiscCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of CLP-0 cells discarded due to policing. " ::= { cpAtmIfStatsEgressEntry 3 } cpAtmIfEgrClp1DiscCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of CLP-1 cells discarded due to policing. " ::= { cpAtmIfStatsEgressEntry 4 } cpAtmIfEgrRcvOAMCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of OAM cells received from the switch at the traffic management and policing device. " ::= { cpAtmIfStatsEgressEntry 5 } cpAtmIfEgrRcvEFCICells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of EFCI cells received from the switch at traffic management and policing device. " ::= { cpAtmIfStatsEgressEntry 6 } -- -- High Capacity Counter objects. These objects are all -- 64 bit versions of the "basic" counters. These -- objects all have the same basic semantics as their 32-bit -- counterparts, however, their syntax has been extended -- to 64 bits. -- cpAtmIfHCEgrRcvClp0Cells OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of CLP-0 cells received from switch at the traffic management and policing device. This object is a 64-bit version of cpAtmIfEgrRcvClp0Cells. " ::= { cpAtmIfStatsEgressEntry 7 } cpAtmIfHCEgrRcvClp1Cells OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of CLP-1 cells received from switch at the traffic management and policing device. This object is a 64-bit version of cpAtmIfEgrRcvClp1Cells. " ::= { cpAtmIfStatsEgressEntry 8 } cpAtmIfHCEgrClp0DiscCells OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of CLP-0 cells discarded due to policing. This object is a 64-bit version of cpAtmIfEgrClp0DiscCells. " ::= { cpAtmIfStatsEgressEntry 9 } cpAtmIfHCEgrClp1DiscCells OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of CLP-1 cells discarded due to policing. This object is a 64-bit version of cpAtmIfEgrClp1DiscCells. " ::= { cpAtmIfStatsEgressEntry 10 } cpAtmIfHCEgrRcvOAMCells OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of OAM cells received from the switch at the traffic management and policing device. This object is a 64-bit version of cpAtmIfEgrRcvOAMCells. " ::= { cpAtmIfStatsEgressEntry 11 } cpAtmIfHCEgrRcvEFCICells OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of EFCI cells received from the switch at traffic management and policing device. This object is a 64-bit version of cpAtmIfEgrRcvEFCICells. " ::= { cpAtmIfStatsEgressEntry 12 } -- ********************************************************************* -- cpAtmIfEgressIntervalTable -- ********************************************************************* cpAtmIfEgressIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF CpAtmIfEgressIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table reflects interval(each 15 minute) statistics associated witheach of the propAtm interfaces on egress side. " ::= { cpAtmIfVirtualPortStats 2 } cpAtmIfEgressIntervalEntry OBJECT-TYPE SYNTAX CpAtmIfEgressIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the cpAtmIfEgressIntervalTable table for each propAtm port interface. CLP-0 means Cell Loss Priority = 0, CLP-1 means Cell Loss Priority = 1. " INDEX { ifIndex, cpAtmIfEgressIntervalNumber} ::= { cpAtmIfEgressIntervalTable 1 } CpAtmIfEgressIntervalEntry ::= SEQUENCE { cpAtmIfEgressIntervalNumber Integer32, cpAtmIfIntEgrRcvClp0Cells Counter32, cpAtmIfIntEgrRcvClp1Cells Counter32, cpAtmIfIntEgrClp0DiscCells Counter32, cpAtmIfIntEgrClp1DiscCells Counter32, cpAtmIfIntEgrRcvOAMCells Counter32, cpAtmIfIntEgrRcvEFCICells Counter32, cpAtmIfHCIntEgrRcvClp0Cells Counter64, cpAtmIfHCIntEgrRcvClp1Cells Counter64, cpAtmIfHCIntEgrClp0DiscCells Counter64, cpAtmIfHCIntEgrClp1DiscCells Counter64, cpAtmIfHCIntEgrRcvOAMCells Counter64, cpAtmIfHCIntEgrRcvEFCICells Counter64 } cpAtmIfEgressIntervalNumber OBJECT-TYPE SYNTAX Integer32(1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index of the table which represents the interval number. An interval number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the 15 minutes interval completed 23 hours an 45 minutes prior to interval 1. " ::= { cpAtmIfEgressIntervalEntry 1 } cpAtmIfIntEgrRcvClp0Cells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of CLP-0 cells received from switch at the traffic management and policing device during a 15 minute interval. " ::= { cpAtmIfEgressIntervalEntry 2 } cpAtmIfIntEgrRcvClp1Cells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of CLP-1 cells received from switch at the traffic management and policing device during a 15 minute interval. " ::= { cpAtmIfEgressIntervalEntry 3 } cpAtmIfIntEgrClp0DiscCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of CLP-0 cells discarded due to policing during a 15 minute interval. " ::= { cpAtmIfEgressIntervalEntry 4 } cpAtmIfIntEgrClp1DiscCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of CLP-1 cells discarded due to policing during a 15 minute interval. " ::= { cpAtmIfEgressIntervalEntry 5 } cpAtmIfIntEgrRcvOAMCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of OAM cells received from the switch at the traffic management and policing device during a 15 minute interval. " ::= { cpAtmIfEgressIntervalEntry 6 } cpAtmIfIntEgrRcvEFCICells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of EFCI cells received from the switch at traffic management and policing device during a 15 minute interval. " ::= { cpAtmIfEgressIntervalEntry 7 } -- -- High Capacity Counter objects. These objects are all -- 64 bit versions of the "basic" counters. These -- objects all have the same basic semantics as their 32-bit -- counterparts, however, their syntax has been extended -- to 64 bits. -- cpAtmIfHCIntEgrRcvClp0Cells OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of CLP-0 cells received from switch at the traffic management and policing device during a 15 minute interval. This object is a 64-bit version of cpAtmIfIntEgrRcvClp0Cells. " ::= { cpAtmIfEgressIntervalEntry 8 } cpAtmIfHCIntEgrRcvClp1Cells OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of CLP-1 cells received from switch at the traffic management and policing device during a 15 minute interval. This object is a 64-bit version of cpAtmIfIntEgrRcvClp1Cells. " ::= { cpAtmIfEgressIntervalEntry 9 } cpAtmIfHCIntEgrClp0DiscCells OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of CLP-0 cells discarded due to policing during a 15 minute interval. This object is a 64-bit version of cpAtmIfIntEgrClp0DiscCells. " ::= { cpAtmIfEgressIntervalEntry 10 } cpAtmIfHCIntEgrClp1DiscCells OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of CLP-1 cells discarded due to policing during a 15 minute interval. This object is a 64-bit version of cpAtmIfIntEgrClp1DiscCells. " ::= { cpAtmIfEgressIntervalEntry 11 } cpAtmIfHCIntEgrRcvOAMCells OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of OAM cells received from the switch at the traffic management and policing device during a 15 minute interval. This object is a 64-bit version of cpAtmIfIntEgrRcvOAMCells. " ::= { cpAtmIfEgressIntervalEntry 12 } cpAtmIfHCIntEgrRcvEFCICells OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of EFCI cells received from the switch at traffic management and policing device during a 15 minute interval. This object is a 64-bit version of cpAtmIfIntEgrRcvEFCICells. " ::= { cpAtmIfEgressIntervalEntry 13 } -- ********************************************************************* -- cpAtmIfStatsIngressTable -- ********************************************************************* cpAtmIfStatsIngressTable OBJECT-TYPE SYNTAX SEQUENCE OF CpAtmIfStatsIngressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table reflects real time statistics associated with each of the the propAtm interfaces on the ingress side. Ingress terminology is used for the cells that are generated by the voice gateway on the TDM side and are going toward the ATM switch. Egress terminology means the cells that are coming from the ATM switch into TDM side. This table contains statistics from this ingress point of view. " ::= { cpAtmIfVirtualPortStats 3 } cpAtmIfStatsIngressEntry OBJECT-TYPE SYNTAX CpAtmIfStatsIngressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the cpAtmIfStatsIngressTable table for each propAtm port interface. CLP-0 means Cell Loss Priority = 0, CLP-1 means Cell Loss Priority = 1. " INDEX { ifIndex } ::= { cpAtmIfStatsIngressTable 1 } CpAtmIfStatsIngressEntry ::= SEQUENCE { cpAtmIfIngXmtClp0Cells Counter32, cpAtmIfIngXmtClp1Cells Counter32, cpAtmIfIngXmtEFCICells Counter32, cpAtmIfIngXmtOAMCells Counter32, cpAtmIfHCIngXmtClp0Cells Counter64, cpAtmIfHCIngXmtClp1Cells Counter64, cpAtmIfHCIngXmtEFCICells Counter64, cpAtmIfHCIngXmtOAMCells Counter64 } cpAtmIfIngXmtClp0Cells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of CLP-0 cells transmitted to the switch after traffic management and policing in ingress direction." ::= {cpAtmIfStatsIngressEntry 1 } cpAtmIfIngXmtClp1Cells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of CLP-1 cells transmitted to the switch after traffic management and policing in ingress direction." ::= {cpAtmIfStatsIngressEntry 2 } cpAtmIfIngXmtEFCICells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of EFCI cells transmitted to the switch after traffic management and policing in ingress direction." ::= {cpAtmIfStatsIngressEntry 3 } cpAtmIfIngXmtOAMCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of OAM loopback cells transmitted to switch after traffic management and policing in ingress direction." ::= {cpAtmIfStatsIngressEntry 4 } -- -- High Capacity Counter objects. These objects are all -- 64 bit versions of the "basic" counters. These -- objects all have the same basic semantics as their 32-bit -- counterparts, however, their syntax has been extended -- to 64 bits. -- cpAtmIfHCIngXmtClp0Cells OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of CLP-0 cells transmitted to the switch after traffic management and policing in ingress direction. This object is a 64-bit version of cpAtmIfIngXmtClp0Cells. " ::= {cpAtmIfStatsIngressEntry 5 } cpAtmIfHCIngXmtClp1Cells OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of CLP-1 cells transmitted to the switch after traffic management and policing in ingress direction. This object is a 64-bit version of cpAtmIfIngXmtClp1Cells. " ::= {cpAtmIfStatsIngressEntry 6 } cpAtmIfHCIngXmtEFCICells OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of EFCI cells transmitted to the switch after traffic management and policing in ingress direction. This object is a 64-bit version of cpAtmIfIngXmtEFCICells. " ::= {cpAtmIfStatsIngressEntry 7 } cpAtmIfHCIngXmtOAMCells OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of OAM loopback cells transmitted to switch after traffic management and policing in ingress direction. This object is a 64-bit version of cpAtmIfIngXmtOAMCells." ::= {cpAtmIfStatsIngressEntry 8 } -- ********************************************************************* -- conformance information -- ********************************************************************* cpAtmIfMIBConformance OBJECT IDENTIFIER ::= { ciscoPropAtmIfMIB 2 } cpAtmIfMIBCompliances OBJECT IDENTIFIER ::= { cpAtmIfMIBConformance 1 } cpAtmIfMIBGroups OBJECT IDENTIFIER ::= { cpAtmIfMIBConformance 2 } -- --Conformance and compliance statements -- cpAtmIfMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for the SNMP entities which implement ciscoPropAtmIfMIB." MODULE -- this module MANDATORY-GROUPS { cpAtmIfConfigGroup } GROUP cpAtmIfEgressStatMIBGroup DESCRIPTION "This group is for the counters with a 32-bit version." GROUP cpAtmIfEgressIntervalMIBGroup DESCRIPTION "This group is for the counters with a 32-bit version." GROUP cpAtmIfIngressStatMIBGroup DESCRIPTION "This group is for the counters with a 32-bit version." GROUP cpAtmIfHCEgressStatMIBGroup DESCRIPTION "This group is for the counters with a 64-bit version." GROUP cpAtmIfHCEgressIntervalMIBGroup DESCRIPTION "This group is for the counters with a 64-bit version." GROUP cpAtmIfHCIngressStatMIBGroup DESCRIPTION "This group is for the counters with a 64-bit version." ::= { cpAtmIfMIBCompliances 1 } -- --units of conformance -- --MIB Groups -- cpAtmIfConfigGroup OBJECT-GROUP OBJECTS { cpAtmIfMaxBandwidth } STATUS current DESCRIPTION "These are objects related to configuration of propAtm Interface. " ::= { cpAtmIfMIBGroups 1 } cpAtmIfEgressStatMIBGroup OBJECT-GROUP OBJECTS { cpAtmIfEgrRcvClp0Cells, cpAtmIfEgrRcvClp1Cells, cpAtmIfEgrClp0DiscCells, cpAtmIfEgrClp1DiscCells, cpAtmIfEgrRcvOAMCells, cpAtmIfEgrRcvEFCICells } STATUS current DESCRIPTION "These are objects related to Egress Statistics of propAtm interfaces. " ::= { cpAtmIfMIBGroups 2 } cpAtmIfEgressIntervalMIBGroup OBJECT-GROUP OBJECTS { cpAtmIfIntEgrRcvClp0Cells, cpAtmIfIntEgrRcvClp1Cells, cpAtmIfIntEgrClp0DiscCells, cpAtmIfIntEgrClp1DiscCells, cpAtmIfIntEgrRcvOAMCells, cpAtmIfIntEgrRcvEFCICells } STATUS current DESCRIPTION "These are objects related to Egress Interval Statistics of propAtm Interfaces. " ::= { cpAtmIfMIBGroups 3 } cpAtmIfIngressStatMIBGroup OBJECT-GROUP OBJECTS { cpAtmIfIngXmtClp0Cells, cpAtmIfIngXmtClp1Cells, cpAtmIfIngXmtEFCICells, cpAtmIfIngXmtOAMCells } STATUS current DESCRIPTION "These are objects related to Ingress Statistics of propAtm interfaces. " ::= { cpAtmIfMIBGroups 4 } cpAtmIfHCEgressStatMIBGroup OBJECT-GROUP OBJECTS { cpAtmIfHCEgrRcvClp0Cells, cpAtmIfHCEgrRcvClp1Cells, cpAtmIfHCEgrClp0DiscCells, cpAtmIfHCEgrClp1DiscCells, cpAtmIfHCEgrRcvOAMCells, cpAtmIfHCEgrRcvEFCICells } STATUS current DESCRIPTION "These are objects related to Egress Statistics of propAtm interfaces. This group is a 64-bit version of cpAtmIfEgressStatMIBGroup. " ::= { cpAtmIfMIBGroups 5 } cpAtmIfHCEgressIntervalMIBGroup OBJECT-GROUP OBJECTS { cpAtmIfHCIntEgrRcvClp0Cells, cpAtmIfHCIntEgrRcvClp1Cells, cpAtmIfHCIntEgrClp0DiscCells, cpAtmIfHCIntEgrClp1DiscCells, cpAtmIfHCIntEgrRcvOAMCells, cpAtmIfHCIntEgrRcvEFCICells } STATUS current DESCRIPTION "These are objects related to Egress Interval Statistics of propAtm Interfaces. This group is a 64-bit version of cpAtmIfEgressIntervalMIBGroup. " ::= { cpAtmIfMIBGroups 6 } cpAtmIfHCIngressStatMIBGroup OBJECT-GROUP OBJECTS { cpAtmIfHCIngXmtClp0Cells, cpAtmIfHCIngXmtClp1Cells, cpAtmIfHCIngXmtEFCICells, cpAtmIfHCIngXmtOAMCells } STATUS current DESCRIPTION "These are objects related to Ingress Statistics of propAtm interfaces. This group is a 64-bit version of cpAtmIfIngressStatMIBGroup. " ::= { cpAtmIfMIBGroups 7 } END