-- ***************************************************************** -- CISCO-OPTICAL-IF-EXTN-MIB.my: Cisco optical IF extension MIB file -- -- May 2002, Suresh Basavarajappa, Mickey Spiegel and Sameer Merchant -- -- Copyright (c) 2001, 2002, 2003, 2004 by cisco Systems, Inc. -- All rights reserved. -- -- ***************************************************************** CISCO-OPTICAL-IF-EXTN-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Unsigned32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF TEXTUAL-CONVENTION FROM SNMPv2-TC ifIndex FROM IF-MIB ciscoExperiment FROM CISCO-SMI ; ciscoOpticalIfExtnMIB MODULE-IDENTITY LAST-UPDATED "200411190000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-dwdm@cisco.com" DESCRIPTION "A MIB module containing extensions to the IF-MIB for optical interfaces." REVISION "200411190000Z" DESCRIPTION "This revision adds 'sonetPhy' and 'multiRate' enumeration to coIfTypeExtn object. " REVISION "200312290000Z" DESCRIPTION "This revision adds 'twoGigabitPhy' enumeration to coIfTypeExtn object. " REVISION "200205230000Z" DESCRIPTION "This revision adds a new table coIfXcvrTable to control transceivers (lasers and optical receivers) at optoelectronic interfaces. It also defines three new code points, ethernetPhy, esconPhy and gigabitPhy for the coIfTypeExtn object. " REVISION "200104200000Z" DESCRIPTION "Initial version of this MIB." ::= { ciscoExperiment 66 } coIfExtnMIBObjects OBJECT IDENTIFIER ::= { ciscoOpticalIfExtnMIB 1 } coIfTypeExtnGroup OBJECT IDENTIFIER ::= { coIfExtnMIBObjects 1 } coIfWavelengthGroup OBJECT IDENTIFIER ::= { coIfExtnMIBObjects 2 } coIfDwdmChannelGroup OBJECT IDENTIFIER ::= { coIfExtnMIBObjects 3 } coIfXcvrGroup OBJECT IDENTIFIER ::= { coIfExtnMIBObjects 4 } -- Textual Conventions CoDwdmFrequency ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The nominal central frequency of one channel in a DWDM system, in GHz." SYNTAX Unsigned32 (1..1000000) CoDwdmFrequencyOrZero ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The nominal central frequency of one channel in a DWDM system, in GHz, or zero. The value zero either indicates that the frequency is unknown, or indicates that this channel is uncolored." SYNTAX Unsigned32 (0..1000000) -- Optical Interface Type Extension Table coIfTypeExtnTable OBJECT-TYPE SYNTAX SEQUENCE OF CoIfTypeExtnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains extensions to the ifType object defined in the IF-MIB for optical interfaces." ::= { coIfTypeExtnGroup 1 } coIfTypeExtnEntry OBJECT-TYPE SYNTAX CoIfTypeExtnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry contains extensions to the ifType object defined in the IF-MIB for one optical interface." INDEX { ifIndex } ::= { coIfTypeExtnTable 1 } CoIfTypeExtnEntry ::= SEQUENCE { coIfTypeExtn INTEGER } coIfTypeExtn OBJECT-TYPE SYNTAX INTEGER { opticalTransponder(1), wdmTransport(2), wdmChannel(3), wdmChannelGroup(4), wavelengthTransport(5), ethernetPhy(6), esconPhy(7), gigabitPhy(8), twoGigabitPhy(9), sonetPhy(10), multiRate(11) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the type of an optical interface, when the type is not specified in the ifType object in the IF-MIB, i.e., when the ifType object is set to 'other'. The value 'opticalTransponder' represents an optoelectronic interface that relays signals of various physical layer protocols. The interface may be capable of pulse shaping and retiming. The interface may be capable of monitoring various physical layer protocols. The interface may emit signals that are colored (e.g. one channel in a DWDM system) or uncolored (i.e., for single channel interfaces). The value 'wdmTransport' indicates an optical interface that carries multiple wavelengths. The value 'wdmChannel' indicates an interface sub-layer above 'wdmTransport' representing a single wavelength. The value 'wdmChannelGroup' indicates an interface sub-layer above 'wdmTransport' representing a wavelength division multiplexed group of wavelengths. The value 'wavelengthTransport' indicates an optical interface that carries a single wavelength. The value 'ethernetPhy' indicates an interface that implements the physical layer of the Ethernet protocol. The value 'esconPhy' indicates an interface that implements the physical layer of ESCON. The value 'gigabitPhy' indicates an interface that supports the physical layers of both Gigabit Ethernet and Fibre Channel. The value 'twoGigabitPhy' indicates an interface that supports the physical layer of 1x and 2x Fibre Channel. The value 'sonetPhy' indicates an interface that carries the trunk side traffic of eight port multirate muxponder The value 'multiRate' indicates an interface that supports client protocols of eight port multirate muxponder ." ::= { coIfTypeExtnEntry 1 } -- Optical Interface Wavelength Table coIfWavelengthTable OBJECT-TYPE SYNTAX SEQUENCE OF CoIfWavelengthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains wavelength information for optical interfaces." ::= { coIfWavelengthGroup 1 } coIfWavelengthEntry OBJECT-TYPE SYNTAX CoIfWavelengthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry contains wavelength information for one optical interface." INDEX { ifIndex } ::= { coIfWavelengthTable 1 } CoIfWavelengthEntry ::= SEQUENCE { coIfDwdmFrequency CoDwdmFrequency } coIfDwdmFrequency OBJECT-TYPE SYNTAX CoDwdmFrequency UNITS "GHz" MAX-ACCESS read-write STATUS current DESCRIPTION "The nominal central frequency associated with this interface, in GHz. This object is instantiated for interfaces with coIfTypeExtn value of 'wdmChannel' and 'wavelengthTransport'. This object may also be instantiated for optoelectronic interfaces that originate or terminate DWDM wavelengths, including some of the interfaces with coIfTypeExtn value of 'opticalTransponder'." ::= { coIfWavelengthEntry 1 } -- DWDM Channel Group Table coIfDwdmChannelGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF CoIfDwdmChannelGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information about interfaces representing groups of DWDM channels. This includes interfaces with coIfTypeExtn value of 'wdmChannelGroup'." ::= { coIfDwdmChannelGroup 3 } coIfDwdmChannelGroupEntry OBJECT-TYPE SYNTAX CoIfDwdmChannelGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry contains information about one interface that represents a group of DWDM channels. The group can be described as a specified set of DWDM frequencies, or as the group of all DWDM frequencies except for those in a specified set. If a frequency is included in a DWDM channel group, this does not necessarily indicate that there is a signal present at that frequency. It indicates that if a signal is present at that frequency, then that signal is included in this DWDM channel group." INDEX { ifIndex } ::= { coIfDwdmChannelGroupTable 1 } CoIfDwdmChannelGroupEntry ::= SEQUENCE { coIfDwdmChannelGroupMinFrequency CoDwdmFrequency, coIfDwdmChannelGroupSpacing Unsigned32, coIfDwdmChannelGroupBitmapLogic INTEGER, coIfDwdmChannelGroupBitmap OCTET STRING } coIfDwdmChannelGroupMinFrequency OBJECT-TYPE SYNTAX CoDwdmFrequency UNITS "GHz" MAX-ACCESS read-write STATUS current DESCRIPTION "The lowest frequency represented in the bitmap specified in coIfDwdmChannelGroupBitmap, i.e., the frequency represented by bit 0 of octet 1 of coIfDwdmChannelGroupBitmap." ::= { coIfDwdmChannelGroupEntry 1 } coIfDwdmChannelGroupSpacing OBJECT-TYPE SYNTAX Unsigned32 (1..1000) UNITS "GHz" MAX-ACCESS read-write STATUS current DESCRIPTION "The difference in frequency between successive bits in coIfDwdmChannelGroupBitmap. This is typically the frequency difference between adjacent channels in the DWDM system." ::= { coIfDwdmChannelGroupEntry 2 } coIfDwdmChannelGroupBitmapLogic OBJECT-TYPE SYNTAX INTEGER { carried(1), blocked(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether coIfDwdmChannelGroupBitmap identifies channels included in the channel group, or whether it identifies channels excluded from the channel group. When the value of this object is 'carried', then the channel group is composed only of those channels for which the value of the corresponding bit in coIfDwdmChannelBitmap is one. When the value of this object is 'blocked', then the channel group is composed of all channels except those for which the value of the corresponding bit in coIfDwdmChannelBitmap is one. Channels that are not identified in coIfDwdmChannelBitmap are included in the channel group." ::= { coIfDwdmChannelGroupEntry 3 } coIfDwdmChannelGroupBitmap OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The DWDM channel bitmap that indicates those channels that are included or excluded (depending on the value of coIfDwdmChannelBitmapLogic) from the DWDM channel group. If a frequency is included in a DWDM channel group, this does not necessarily indicate that there is a signal present at that frequency. It indicates that if a signal is present at that frequency, then that signal is included in this DWDM channel group. Bit zero of octet one corresponds to the lowest channel (representing the frequency identified by coIfDwdmChannelGroupMinFrequency), bit one of octet one corresponds to the lowest plus one channel (representing the frequency obtained by adding the values of coIfDwdmChannelGroupMinFrequency and coIfDwdmChannelGroupSpacing), and so on. When the value of coIfDwdmChannelBitmapLogic is 'carried', then channels included in the channel group will have the corresponding bit set to one in the bitmap. Bits that are set to zero represent channels that are excluded from the channel group. Channels that are not represented in the bitmap are also excluded from the channel group. When the value of coIfDwdmChannelBitmapLogic is 'blocked', then channels excluded from the channel group will have the corresponding bit set to one in the bitmap. Bits that are set to zero represent channels that are included in the channel group. Channels that are not represented in the bitmap are also included in the channel group." ::= { coIfDwdmChannelGroupEntry 4 } -- Optical Interface Transceiver Table coIfXcvrTable OBJECT-TYPE SYNTAX SEQUENCE OF CoIfXcvrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains objects to control transceivers (lasers and optical receivers) at optoelectronic interfaces." ::= { coIfXcvrGroup 1 } coIfXcvrEntry OBJECT-TYPE SYNTAX CoIfXcvrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry contains objects for control of a transceiver at an optoelectronic interface." INDEX { ifIndex } ::= { coIfXcvrTable 1 } CoIfXcvrEntry ::= SEQUENCE { coIfXcvrLaserAdminStatus INTEGER, coIfXcvrLaserOperStatus INTEGER, coIfXcvrMinLaserFrequency CoDwdmFrequencyOrZero, coIfXcvrLaserFrequencySpacing Unsigned32, coIfXcvrLaserFrequencyBitmap OCTET STRING, coIfXcvrForwardLaserControl INTEGER, coIfXcvrLaserSafetyControl INTEGER, coIfXcvrLSCProtocol INTEGER, coIfXcvrLSCRestartMode INTEGER, coIfXcvrLSCManualRestart INTEGER, coIfXcvrLSCPulseLength Unsigned32, coIfXcvrLSCTestPulseLength Unsigned32, coIfXcvrLSCPulseRepetitionTime Unsigned32 } coIfXcvrLaserAdminStatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The desired state of the laser on this interface. This object differs from ifAdminStatus in the IF-MIB, since in some cases setting ifAdminStatus to 'down' causes an alarm indication to be transmitted, rather than shutting down the laser. When this object is set to 'down', ifOperStatus in the IF-MIB goes to the 'down' state, and the laser is shut down. In order to administratively enable an interface, both ifAdminStatus in the IF-MIB and this object must be set to 'up'." ::= { coIfXcvrEntry 1 } coIfXcvrLaserOperStatus OBJECT-TYPE SYNTAX INTEGER { transmitting(1), degraded(2), down(3), lscDown(4), flcDown(5), unknown(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the current operational status of the laser on this interface. 'transmitting': The laser is on. 'degraded': The laser is on, but there is a fault that causes it to transmit in a degraded manner. 'down': The laser is shut down, either because of error conditions or because it has been administratively disabled. This state indicates that the laser is shut down due to conditions other than Laser Safety Control or Forward Laser Control. 'lscDown': The laser is shut down due to Laser Safety Control (LSC) mechanisms such as Automatic Laser Shutdown (ALS), i.e., due to a fault in the receive direction at this interface. 'flcDown': The laser is shut down due to Forward Laser Control, i.e., due to a fault on the cross-connected interface. 'unknown': The operational status of the laser cannot be determined. If the value of coIfXcvrLaserAdminStatus is 'down', then this object also indicates 'down'. If coIfXcvrLaserAdminStatus is set to 'up', then the value of this object should change to 'transmitting' if the laser is functioning properly." ::= { coIfXcvrEntry 2 } coIfXcvrMinLaserFrequency OBJECT-TYPE SYNTAX CoDwdmFrequencyOrZero UNITS "GHz" MAX-ACCESS read-write STATUS current DESCRIPTION "The lowest frequency represented in the bitmap specified in coIfXcvrLaserFrequencyBitmap, i.e., the frequency represented by bit 0 of octet 1 of coIfXcvrLaserFrequencyBitmap. A value of zero signifies that the laser on this interface is uncolored and that coIfXcvrLaserFrequencyBitmap does not apply." ::= { coIfXcvrEntry 3 } coIfXcvrLaserFrequencySpacing OBJECT-TYPE SYNTAX Unsigned32 (1..1000) UNITS "GHz" MAX-ACCESS read-write STATUS current DESCRIPTION "The difference in frequency between successive bits in coIfXcvrLaserFrequencyBitmap. This is typically the frequency difference between adjacent channels in the DWDM system." ::= { coIfXcvrEntry 4 } coIfXcvrLaserFrequencyBitmap OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "This bitmap indicates the DWDM channel frequencies supported by the tunable laser on this interface. Bit zero of octet one corresponds to the lowest channel (representing the frequency identified by coIfXcvrMinLaserFrequency), bit one of octet one corresponds to the lowest plus one channel (representing the frequency obtained by adding the values of coIfXcvrMinLaserFrequency and coIfXcvrMinLaserFrequencySpacing), and so on. The frequencies supported by the tunable laser have the corresponding bit set to one in the bitmap. Bits that are set to zero represent frequencies that are not supported by the tunable laser. The frequencies that are not represented in the bitmap are also not supported by the tunable laser." ::= { coIfXcvrEntry 5 } coIfXcvrForwardLaserControl OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to enable or disable Forward Laser Control (FLC) on this interface. If Forward Laser Control is enabled, the laser is automatically shut down when the receive direction of the cross-connected interface is in an alarm condition." ::= { coIfXcvrEntry 6 } coIfXcvrLaserSafetyControl OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to enable or disable Laser Safety Control (LSC) mechanisms such as Automatic Laser Shutdown (ALS) on this interface. Laser Safety Control mechanisms are used to automatically shutdown the output power of laser transmitters when potentially hazardous conditions such as fiber breaks or unplugged optical connectors are detected." ::= { coIfXcvrEntry 7 } coIfXcvrLSCProtocol OBJECT-TYPE SYNTAX INTEGER { proprietary(1), g664(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object identifies the Laser Safety Control protocol that is applied when coIfXcvrLaserSafetyControl is set to 'enable'. 'proprietary': Indicates that the Laser Safety Control protocol is proprietary. 'g664': Indicates the Automatic Laser Shutdown (ALS) protocol specified in ITU-T Recommendation G.664." REFERENCE "ITU-T Recommendation G.664, Optical safety procedures and requirements for optical transport systems, June 1999" ::= { coIfXcvrEntry 8 } coIfXcvrLSCRestartMode OBJECT-TYPE SYNTAX INTEGER { automaticRestart(1), manualRestart(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object selects the mechanism used to restore transmission after the fiber has been repaired or reconnected. 'automaticRestart': This mode selects automatic restart of the laser by periodically transmitting restart pulses. The period between restart pulse transmissions is specified by coIfXcvrLSCPulseReptitionTime. 'manualRestart': This mode selects manual restart of the laser. After the fiber has been repaired or reconnected, the coIfXcvrLSCManualRestart object should be used to trigger transmission of a restart pulse." ::= { coIfXcvrEntry 9 } coIfXcvrLSCManualRestart OBJECT-TYPE SYNTAX INTEGER { noop(1), restart(2), restartForTest(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object initiates laser activation when the laser is shut down due to Laser Safety Control. When the value is set to 'restart', transmission of a restart pulse of length coIfXcvrLSCPulseLength is triggered. When this object is set to 'restartForTest', transmission of a restart pulse of length coIfXcvrLSCTestPulseLength is triggered. Before setting this object to 'restartForTest', specific care must be taken to assure connectivity to avoid exposure to hazardous optical levels. When the value is set to 'noop', no operation is performed. When read, the value 'noop' is returned. Manual restart can only be activated when the value of coIfXcvrLaserOperStatus is 'lscDown'." ::= { coIfXcvrEntry 10 } coIfXcvrLSCPulseLength OBJECT-TYPE SYNTAX Unsigned32 (100..20000) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the length of restart pulses used to restore transmission when a Laser Safety Control protocol is activated." ::= { coIfXcvrEntry 11 } coIfXcvrLSCTestPulseLength OBJECT-TYPE SYNTAX Unsigned32 (1..300) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the length of test restart pulses that are transmitted when coIfXcvrLSCManualRestart is set to 'restartForTest'." ::= { coIfXcvrEntry 12 } coIfXcvrLSCPulseRepetitionTime OBJECT-TYPE SYNTAX Unsigned32 (1..300) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the delay interval between transmissions of restart pulses, when coIfXcvrLSCRestartMode is set to 'automaticRestart' and coIfXcvrLaserOperStatus indicates 'lscDown'." ::= { coIfXcvrEntry 13 } -- conformance information coIfExtnMIBConformance OBJECT IDENTIFIER ::= { ciscoOpticalIfExtnMIB 3 } coIfExtnMIBCompliances OBJECT IDENTIFIER ::= { coIfExtnMIBConformance 1 } coIfExtnMIBGroups OBJECT IDENTIFIER ::= { coIfExtnMIBConformance 2 } coIfExtnMIBCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the Cisco Optical Interface Extensions MIB." MODULE -- this module MANDATORY-GROUPS { coIfWavelengthMIBGroup } GROUP coIfTypeExtnMIBGroup DESCRIPTION "This group should be implemented only by entities containing interfaces whose type is not defined in the IANAifType textual convention." OBJECT coIfDwdmFrequency MIN-ACCESS read-only DESCRIPTION "Write-access applies only when interfaces with tunable lasers or tunable filters are present. This object is supported by entities with interfaces that carry a single wavelength or frequency. This includes interfaces with coIfTypeExtn value of 'wdmChannel' and 'wavelengthTransport'. This also includes optoelectronic interfaces that originate and terminate DWDM wavelengths, including some of the interfaces with coIfTypeExtn value of 'opticalTransponder'." GROUP coIfDwdmChannelGroupMIBGroup DESCRIPTION "This group is required for systems supporting interfaces representing groups of DWDM channels. This includes interfaces with coIfTypeExtn value of 'wdmChannelGroup'." OBJECT coIfDwdmChannelGroupMinFrequency MIN-ACCESS read-only DESCRIPTION "Write-access applies only when tunable or switchable filters are present." OBJECT coIfDwdmChannelGroupSpacing MIN-ACCESS read-only DESCRIPTION "Write-access applies only when tunable or switchable filters are present." OBJECT coIfDwdmChannelGroupBitmapLogic MIN-ACCESS read-only DESCRIPTION "Write-access applies only when tunable or switchable filters are present." OBJECT coIfDwdmChannelGroupBitmap MIN-ACCESS read-only DESCRIPTION "Write-access applies only when tunable or switchable filters are present." ::= { coIfExtnMIBCompliances 1 } coIfExtnMIBCompliance2 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for the Cisco Optical Interface Extensions MIB." MODULE -- this module MANDATORY-GROUPS { coIfWavelengthMIBGroup } GROUP coIfTypeExtnMIBGroup DESCRIPTION "This group should be implemented only by entities containing interfaces whose type is not defined in the IANAifType textual convention." OBJECT coIfDwdmFrequency MIN-ACCESS read-only DESCRIPTION "Write-access applies only when interfaces with tunable lasers or tunable filters are present. This object is supported by entities with interfaces that carry a single wavelength or frequency. This includes interfaces with coIfTypeExtn value of 'wdmChannel' and 'wavelengthTransport'. This also includes optoelectronic interfaces that originate and terminate DWDM wavelengths, including some of the interfaces with coIfTypeExtn value of 'opticalTransponder'." GROUP coIfDwdmChannelGroupMIBGroup DESCRIPTION "This group is required for systems supporting interfaces representing groups of DWDM channels. This includes interfaces with coIfTypeExtn value of 'wdmChannelGroup'." OBJECT coIfDwdmChannelGroupMinFrequency MIN-ACCESS read-only DESCRIPTION "Write-access applies only when tunable or switchable filters are present." OBJECT coIfDwdmChannelGroupSpacing MIN-ACCESS read-only DESCRIPTION "Write-access applies only when tunable or switchable filters are present." OBJECT coIfDwdmChannelGroupBitmapLogic MIN-ACCESS read-only DESCRIPTION "Write-access applies only when tunable or switchable filters are present." OBJECT coIfDwdmChannelGroupBitmap MIN-ACCESS read-only DESCRIPTION "Write-access applies only when tunable or switchable filters are present." GROUP coIfXcvrBaseMIBGroup DESCRIPTION "This group is optional." OBJECT coIfXcvrLaserAdminStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT coIfXcvrForwardLaserControl MIN-ACCESS read-only DESCRIPTION "Write access is not required." GROUP coIfXcvrTunableLaserMIBGroup DESCRIPTION "This group is required for systems supporting tunable lasers." GROUP coIfXcvrLSCMIBGroup DESCRIPTION "This group is required for systems supporting Laser Safety Control (LSC) mechanisms such as Automatic Laser Shutdown (ALS)." OBJECT coIfXcvrLSCProtocol MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT coIfXcvrLSCRestartMode MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT coIfXcvrLSCManualRestart MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT coIfXcvrLSCPulseLength MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT coIfXcvrLSCTestPulseLength MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT coIfXcvrLSCPulseRepetitionTime MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { coIfExtnMIBCompliances 2 } -- units of conformance coIfTypeExtnMIBGroup OBJECT-GROUP OBJECTS { coIfTypeExtn } STATUS current DESCRIPTION "A collection of managed objects providing extensions to the interface type information found in the IF-MIB." ::= { coIfExtnMIBGroups 1 } coIfWavelengthMIBGroup OBJECT-GROUP OBJECTS { coIfDwdmFrequency } STATUS current DESCRIPTION "A collection of managed objects providing information about the wavelength or frequency of optical interfaces." ::= { coIfExtnMIBGroups 2 } coIfDwdmChannelGroupMIBGroup OBJECT-GROUP OBJECTS { coIfDwdmChannelGroupMinFrequency, coIfDwdmChannelGroupSpacing, coIfDwdmChannelGroupBitmapLogic, coIfDwdmChannelGroupBitmap } STATUS current DESCRIPTION "A collection of managed objects providing information about DWDM channel groups." ::= { coIfExtnMIBGroups 3 } coIfXcvrBaseMIBGroup OBJECT-GROUP OBJECTS { coIfXcvrLaserAdminStatus, coIfXcvrLaserOperStatus, coIfXcvrForwardLaserControl } STATUS current DESCRIPTION "A collection of managed objects for control of transceivers (lasers and optical receivers) at optoelectronic interfaces." ::= { coIfExtnMIBGroups 4 } coIfXcvrTunableLaserMIBGroup OBJECT-GROUP OBJECTS { coIfXcvrMinLaserFrequency, coIfXcvrLaserFrequencySpacing, coIfXcvrLaserFrequencyBitmap } STATUS current DESCRIPTION "A collection of managed objects providing information about tunable lasers." ::= { coIfExtnMIBGroups 5 } coIfXcvrLSCMIBGroup OBJECT-GROUP OBJECTS { coIfXcvrLaserSafetyControl, coIfXcvrLSCProtocol, coIfXcvrLSCRestartMode, coIfXcvrLSCManualRestart, coIfXcvrLSCPulseLength, coIfXcvrLSCTestPulseLength, coIfXcvrLSCPulseRepetitionTime } STATUS current DESCRIPTION "A collection of managed objects for Laser Safety Control (LSC) mechanisms such as Automatic Laser Shutdown (ALS)." ::= { coIfExtnMIBGroups 6 } END