-- ***************************************************************** -- CISCO-NETSYNC-MIB.my: Cisco SyncE MIB -- -- October 2010, Danny Lee -- -- Copyright (c) 2010 by cisco Systems Inc. -- All rights reserved. -- -- ***************************************************************** CISCO-NETSYNC-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Gauge32, Unsigned32 FROM SNMPv2-SMI MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP FROM SNMPv2-CONF TruthValue, TEXTUAL-CONVENTION, TimeStamp FROM SNMPv2-TC SnmpAdminString FROM SNMP-FRAMEWORK-MIB ciscoMgmt FROM CISCO-SMI; ciscoNetsyncMIB MODULE-IDENTITY LAST-UPDATED "201010150000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-sync-e@cisco.com" DESCRIPTION "The Synchronous Ethernet (SyncE) MIB is defined for monitoring network synchronization based on ITU-T G.781 clock selection. Synchronous Ethernet (SyncE) is a standard defined for delivering timing to the remote NEs through a Packet Network. SyncE is well defined by ITU-T which included G.8261, G.8262, G.8264 and G.781. It leverages the PHY layer of Ethernet to transmit frequency to the remote sites. Its functionality and accuracy mimics that of the SONET/SDH network because of its physical layer characteristic. In order to allow best clock source traceabiliy, correctly define the timing source and helps preventing timing loop, Synchronization Status Message is required for SyncE. This is similar to SONET/SDH. However, since SONET/SDH use 4 bits from the two S bytes in the SONET/SDH overhead frame for such message, Ethernet relies on a different channel called ESMC (Ethernet Synchronization Messaging Channel) which is based on IEEE 802.3 Organization Specific Slow Protocol. Glossary: AIS: Alarm Indication Signal ATM: Asynchronous Transfer Mode EEC: Ethernet Equipment Clock ESMC: Ethernet Synchronization Messaging Channel QL: Quality Level SASE: Stand Alone Synchronization Equipment SSM: Synchronization Status Messaging" REVISION "201010150000Z" DESCRIPTION "Initial version of the SyncE MIB module." ::= { ciscoMgmt 761 } -- Textual Conventions CiscoNetsyncIfType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Network synchronization clock source Interface type. Netsync interface Interface type ======================== ============== netsyncIfTypeUnknown Unknown netsyncIfTypeInternal Internal netsyncIfTypeEthernet Ethernet netsyncIfTypeSonet SONET netsyncIfTypeTop Timing Over Packet netsyncIfTypeExt External interface netsyncIfTypeController T1/E1 Controller netsyncIfTypeGps GPS netsyncIfTypeAtm ATM For external and GPS interface types, the following syntax is used for specifying an interface: // where slot : slot number of the device where card is present. card : bay number in which card is inserted. port : port number on the card. signal type: hardware signal of the specified //. Examples of signal type are T1 SF and T1 ESF. " SYNTAX INTEGER { netsyncIfTypeUnknown(1), netsyncIfTypeInternal(2), netsyncIfTypeEthernet(3), netsyncIfTypeSonet(4), netsyncIfTypeTop(5), netsyncIfTypeExt(6), netsyncIfTypeController(7), netsyncIfTypeGps(8), netsyncIfTypeAtm(9) } CiscoNetsyncNetworkOption ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Network synchronization networking options. Network option Network option type =========================== =================== netsyncNetworkOptionUnknown Unknown network option netsyncNetworkOption1 Option I netsyncNetworkOption2Gen1 Option II Generation 1 netsyncNetworkOption2Gen2 Option II Generation 2 netsyncNetworkOption3 Option III netsyncNetworkOptionInvalid Invalid network option Option I refers to ITU-T Option I synchronization networks. Option II refers to ITU-T Option II synchronization networks designed for North America. Option III refers to ITU-T Option III synchronization networks designed for Japan. " REFERENCE "ITU-T standard G.781" SYNTAX INTEGER { netsyncNetworkOptionUnknown(1), netsyncNetworkOption1(2), netsyncNetworkOption2Gen1(3), netsyncNetworkOption2Gen2(4), netsyncNetworkOption3(5), netsyncNetworkOptionInvalid(6) } CiscoNetsyncEECOption ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Network synchronization EEC (Ethernet Equipment Clock) options. The EEC options are for Synchronous Ethernet devices and define the requirements for clocks, e.g. bandwidth, frequency accuracy, holdover and noise generation. Two options are defined: EEC-Option 1: Designed to interwork with network optimized for the 2048 kbit/s hierarchy. EEC-Option 2: Designed to interwork with network optimized for the 1544 kbit/s hierarchy. netsyncEECOptionUnknown Unknown netsyncEECOption1 EEC option 1 netsyncEECOption2 EEC option 2 netsyncEECOptionInvalid Invalid EEC option " REFERENCE "ITU-T standard G.781" SYNTAX INTEGER { netsyncEECOptionUnknown(1), netsyncEECOption1(2), netsyncEECOption2(3), netsyncEECOptionInvalid(4) } CiscoNetsyncQLMode ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The clock mode of the network synchronization clock selection process as described in ITU-T standard G.781 section 5.12. G.781 clock selection runs in one of two clock modes: QL (Quality Level) enabled mode and QL disabled mode. netsyncQLModeUnknown - QL mode unknown netsyncQLModeQlDisabled - QL-disabled mode; clock selection is running in QL disabled mode, which primarily considers the source's priority as the clock selection criteria. netsyncQLModeQlEnabled - QL-enabled mode clock selection is running in QL enabled mode, which primarily considers the source's clock quality level and priority as the clock selection criteria. " REFERENCE "ITU-T standard G.781 section 5.12" SYNTAX INTEGER { netsyncQLModeUnknown(1), netsyncQLModeQlDisabled(2), netsyncQLModeQlEnabled(3) } CiscoNetsyncClockMode ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Clock operating mode: netsyncClockModeUnknown - system is unable to determine the operating mode. netsyncClockModeFreerun - free-running mode. netsyncClockModeHoldover - holdover mode. netsyncClockModeLocked - a valid clock source is locked. " SYNTAX INTEGER { netsyncClockModeUnknown(1), netsyncClockModeFreerun(2), netsyncClockModeHoldover(3), netsyncClockModeLocked(4) } CiscoNetsyncQualityLevel ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Clock source QL (quality level) is defined in ITU-T G.781 section 5.4 to reflect the synchronization quality within a network Option, i.e. I, II, and III. The following clock source quality levels are defined for the synchronization process of Option I: QL-PRC Primary reference clock QL-SSU-A Type I or V slave clock defined in ITU-T G.811 QL-SSU-B Type VI slave clock defined in ITU-T G.812 QL-SEC Synchronous equipment clock QL-DNU Do not use for synchronization QL-INVx Unallocated SSM value, where x represent the value of SSM received QL-FAILED Signal failure state QL-UNC Unconnected to an input QL-NSUPP Not supporting the SSM processing The following clock source quality levels are defined for the synchronization process of Option II: QL-PRS PRS traceable QL-STU Synchronized; traceability unknown QL-ST2 Stratum 2 QL-TNC Transit node clock QL-ST3E Stratum 3E QL-ST3 Stratum 3 QL-SMC SONET clock self timed QL-ST4 Stratum 4 freerun QL-PROV Provisionable by the network operator QL-DUS Do not use for synchronization QL-INVx Unallocated SSM value, where x represent the value of SSM received QL-FAILED Signal failure state QL-UNC Unconnected to an input QL-NSUPP Not supporting the SSM processing The following clock source quality levels are defined for the synchronization process of Option III: QL-UNK Unknown clock source QL-SEC Synchronous equipment clock QL-INVx Unallocated SSM value, where x represent the value of SSM received QL-FAILED Signal failure state QL-UNC Unconnected to an input QL-NSUPP Not supporting the SSM processing " REFERENCE "ITU-T standard G.781 section 5.4" SYNTAX INTEGER { netsyncQualityLevelNULL(1), netsyncQualityLevelDNU(2), netsyncQualityLevelDUS(3), netsyncQualityLevelFAILED(4), netsyncQualityLevelINV0(5), netsyncQualityLevelINV1(6), netsyncQualityLevelINV2(7), netsyncQualityLevelINV3(8), netsyncQualityLevelINV4(9), netsyncQualityLevelINV5(10), netsyncQualityLevelINV6(11), netsyncQualityLevelINV7(12), netsyncQualityLevelINV8(13), netsyncQualityLevelINV9(14), netsyncQualityLevelINV10(15), netsyncQualityLevelINV11(16), netsyncQualityLevelINV12(17), netsyncQualityLevelINV13(18), netsyncQualityLevelINV14(19), netsyncQualityLevelINV15(20), netsyncQualityLevelNSUPP(21), netsyncQualityLevelPRC(22), netsyncQualityLevelPROV(23), netsyncQualityLevelPRS(24), netsyncQualityLevelSEC(25), netsyncQualityLevelSMC(26), netsyncQualityLevelSSUA(27), netsyncQualityLevelSSUB(28), netsyncQualityLevelST2(29), netsyncQualityLevelST3(30), netsyncQualityLevelST3E(31), netsyncQualityLevelST4(32), netsyncQualityLevelSTU(33), netsyncQualityLevelTNC(34), netsyncQualityLevelUNC(35), netsyncQualityLevelUNK(36) } CiscoNetsyncSSMCap ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Network synchronization clock source interface SSM (Synchronization Status Message) capability. SSM Capability Capability information ===================== ====================== netsyncSSMCapNone No SSM capability netsyncSSMCapTxRx To transmit and receive SSM netsyncSSMCapTx To transmit SSM only netsyncSSMCapRx To receive SSM only netsyncSSMCapInvalid Capability invalid or unsupported " SYNTAX INTEGER { netsyncSSMCapNone(1), netsyncSSMCapTxRx(2), netsyncSSMCapTx(3), netsyncSSMCapRx(4), netsyncSSMCapInvalid(5) } CiscoNetsyncESMCCap ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Network synchronization clock source interface ESMC (Ethernet Synchronization Messaging Channel) capability. ESMC Capability Capability information ====================== ====================== netsyncESMCCapNone No ESMC capability netsyncESMCCapTxRx To transmit and receive ESMC netsyncESMCCapTx To transmit SSM only netsyncESMCCapRx To receive SSM only netsyncESMCCapInvalid Capability invalid or unsupported " SYNTAX INTEGER { netsyncESMCCapNone(1), netsyncESMCCapTxRx(2), netsyncESMCCapTx(3), netsyncESMCCapRx(4), netsyncESMCCapInvalid(5) } CiscoNetsyncAlarmInfo ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Input clock source's alarm reasons: netsyncSrcAlarmReasonAIS - Alarm Indication Signal netsyncSrcAlarmReasonOOR - Out of range netsyncSrcAlarmReasonOIR - Online Insertion Removal netsyncSrcAlarmReasonInternal - Internal" SYNTAX BITS { netsyncSrcAlarmReasonAIS(0), netsyncSrcAlarmReasonOOR(1), netsyncSrcAlarmReasonOIR(2), netsyncSrcAlarmReasonInternal(3) } -- Textual Conventions definition will be defined before this line ciscoNetsyncMIBNotifs OBJECT IDENTIFIER ::= { ciscoNetsyncMIB 0 } ciscoNetsyncMIBObjects OBJECT IDENTIFIER ::= { ciscoNetsyncMIB 1 } ciscoNetsyncMIBConform OBJECT IDENTIFIER ::= { ciscoNetsyncMIB 2 } ciscoNetsyncMIBTables OBJECT IDENTIFIER ::= { ciscoNetsyncMIBObjects 1 } cnsClkSelGlobalTable OBJECT-TYPE SYNTAX SEQUENCE OF CnsClkSelGlobalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "G.781 clock selection process table. This table contains the global parameters for the G.781 clock selection process." ::= { ciscoNetsyncMIBTables 1 } cnsClkSelGlobalEntry OBJECT-TYPE SYNTAX CnsClkSelGlobalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is added to cnsClkSelGlobalTable when G.781 clock selection is enabled in the device configuration. The entry is removed when G.781 clock selection is removed from the configuration." INDEX { cnsClkSelGloProcIndex } ::= { cnsClkSelGlobalTable 1 } CnsClkSelGlobalEntry ::= SEQUENCE { cnsClkSelGloProcIndex Unsigned32, cnsClkSelGlobProcessMode CiscoNetsyncQLMode, cnsClkSelGlobClockMode CiscoNetsyncClockMode, cnsClkSelGlobNetsyncEnable TruthValue, cnsClkSelGlobRevertiveMode TruthValue, cnsClkSelGlobESMCMode TruthValue, cnsClkSelGlobEECOption CiscoNetsyncEECOption, cnsClkSelGlobNetworkOption CiscoNetsyncNetworkOption, cnsClkSelGlobHoldoffTime Unsigned32, cnsClkSelGlobWtrTime Unsigned32, cnsClkSelGlobNofSources Unsigned32, cnsClkSelGlobLastHoldoverSeconds Gauge32, cnsClkSelGlobCurrHoldoverSeconds Gauge32 } cnsClkSelGloProcIndex OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index that uniquely represents a clock selection process. This index is assigned arbitrarily by the system and may not be persistent across reboots." ::= { cnsClkSelGlobalEntry 1 } cnsClkSelGlobProcessMode OBJECT-TYPE SYNTAX CiscoNetsyncQLMode MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the QL mode of the network synchronization clock selection process as described in ITU-T standard G.781 section 5.12. " ::= { cnsClkSelGlobalEntry 2 } cnsClkSelGlobClockMode OBJECT-TYPE SYNTAX CiscoNetsyncClockMode MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the operating mode of the system clock." ::= { cnsClkSelGlobalEntry 3 } cnsClkSelGlobNetsyncEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether the G.781 clock selection is enabled or not. 'true' - G.781 clock selection is enabled 'false' - G.781 clock selection is disabled" DEFVAL { false } ::= { cnsClkSelGlobalEntry 4 } cnsClkSelGlobRevertiveMode OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the revertive mode setting in the G.781 clock selection process. The switching of clock sources can be made revertive or non-revertive. In non-revertive mode, an alternate clock source is maintained even after the original clock source has recovered from the failure that caused the switch. In revertive mode, the clock selection process switches back to the original clock source after recovering from the failure." DEFVAL { false } ::= { cnsClkSelGlobalEntry 5 } cnsClkSelGlobESMCMode OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates if global ESMC is enabled. With ESMC enabled globally, the system is capable of handling ESMC messages." DEFVAL { false } ::= { cnsClkSelGlobalEntry 6 } cnsClkSelGlobEECOption OBJECT-TYPE SYNTAX CiscoNetsyncEECOption MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the network synchronization EEC (Ethernet Equipment Clock) option." REFERENCE "ITU-T standard G.781" DEFVAL { netsyncEECOptionUnknown } ::= { cnsClkSelGlobalEntry 7 } cnsClkSelGlobNetworkOption OBJECT-TYPE SYNTAX CiscoNetsyncNetworkOption MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the synchronization network option." REFERENCE "ITU-T standard G.781" DEFVAL { netsyncNetworkOptionUnknown } ::= { cnsClkSelGlobalEntry 8 } cnsClkSelGlobHoldoffTime OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the global holdoff time in the G.781 clock selection process." REFERENCE "ITU-T standard G.781 section 5.8" DEFVAL { 300 } ::= { cnsClkSelGlobalEntry 9 } cnsClkSelGlobWtrTime OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the global wait-to-restore time in the G.781 clock selection process." REFERENCE "ITU-T standard G.781 section 5.9" DEFVAL { 300 } ::= { cnsClkSelGlobalEntry 10 } cnsClkSelGlobNofSources OBJECT-TYPE SYNTAX Unsigned32 (1..255) UNITS "clock sources" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of synchronization sources currently configured for the G.781 clock selection process." ::= { cnsClkSelGlobalEntry 11 } cnsClkSelGlobLastHoldoverSeconds OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the duration of the last holdover period in seconds. If the holdover duration is less than a second, the object will carry the value zero." ::= { cnsClkSelGlobalEntry 12 } cnsClkSelGlobCurrHoldoverSeconds OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the duration of the current holdover period. If a system clock is in holdover mode, the object carries the current holdover duration in seconds. If the system clock is not in holdover, the object carries the value 0." ::= { cnsClkSelGlobalEntry 13 } cnsSelectedInputSourceTable OBJECT-TYPE SYNTAX SEQUENCE OF CnsSelectedInputSourceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "T0 selected clock source table. This table contains the selected clock source for the input T0 clock." ::= { ciscoNetsyncMIBTables 2 } cnsSelectedInputSourceEntry OBJECT-TYPE SYNTAX CnsSelectedInputSourceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created in the table when the G.781 clock selection process has successfully selected a T0 clock source. The entry shall remain during the time the G.781 clock selection process remains enabled." INDEX { cnsSelInpSrcNetsyncIndex } ::= { cnsSelectedInputSourceTable 1 } CnsSelectedInputSourceEntry ::= SEQUENCE { cnsSelInpSrcNetsyncIndex Unsigned32, cnsSelInpSrcName SnmpAdminString, cnsSelInpSrcIntfType CiscoNetsyncIfType, cnsSelInpSrcQualityLevel CiscoNetsyncQualityLevel, cnsSelInpSrcPriority Unsigned32, cnsSelInpSrcTimestamp TimeStamp, cnsSelInpSrcFSW TruthValue, cnsSelInpSrcMSW TruthValue } cnsSelInpSrcNetsyncIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index that uniquely represents an entry in this table. This index is assigned arbitrarily by the clock selection process and may not be persistent across reboots." ::= { cnsSelectedInputSourceEntry 1 } cnsSelInpSrcName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the name of the selected T0 clock." ::= { cnsSelectedInputSourceEntry 2 } cnsSelInpSrcIntfType OBJECT-TYPE SYNTAX CiscoNetsyncIfType MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the type of the selected T0 clock." ::= { cnsSelectedInputSourceEntry 3 } cnsSelInpSrcQualityLevel OBJECT-TYPE SYNTAX CiscoNetsyncQualityLevel MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the selected T0 clock source's effective quality level, which is the derived clock quality based on the three factors: (a) Received quality level. (b) Configured Rx quality level. This factor supersedes (a). (c) System overridden quality level as a result of exceptional events such as signal failure or ESMC failure. This factor supersedes (a) and (b)." ::= { cnsSelectedInputSourceEntry 4 } cnsSelInpSrcPriority OBJECT-TYPE SYNTAX Unsigned32 (1..1024) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the configured priority of the selected T0 clock. A smaller value represents a higher priority." REFERENCE "ITU-T standard G.781 section 5.10" ::= { cnsSelectedInputSourceEntry 5 } cnsSelInpSrcTimestamp OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the timestamp of the T0 clock source being selected by the G.781 clock selection process." ::= { cnsSelectedInputSourceEntry 6 } cnsSelInpSrcFSW OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the forced switching flag. Forced switching, as described in G.781, is used to override the currently selected synchronization source. The 'true' value indicates the currently selected clock source is a result of the forced switching. The 'false' value indicates the currently selected clock source is not a result of forced switching." REFERENCE "ITU-T standard G.781 section 5.11.2.2" ::= { cnsSelectedInputSourceEntry 7 } cnsSelInpSrcMSW OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the manual switching flag. The 'true' value indicates the currently selected clock source is a result of the manual switch command. The command allows a user to select a synchronization source assuming it is enabled, not locked out, not in signal fail condition, and has a QL better than DNU in QL-enabled mode. Furthermore, in QL-enabled mode, a manual switch can be performed only to a source which has the highest available QL." REFERENCE "ITU-T standard G.781 section 5.11.2.3" ::= { cnsSelectedInputSourceEntry 8 } cnsInputSourceTable OBJECT-TYPE SYNTAX SEQUENCE OF CnsInputSourceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "T0 clock source table. This table contains a list of input sources for input T0 clock selection." ::= { ciscoNetsyncMIBTables 3 } cnsInputSourceEntry OBJECT-TYPE SYNTAX CnsInputSourceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created in the table when a user adds a T0 clock source in the configuration. An entry is removed in the table when a user removes a T0 clock source from the configuration." INDEX { cnsInpSrcNetsyncIndex } ::= { cnsInputSourceTable 1 } CnsInputSourceEntry ::= SEQUENCE { cnsInpSrcNetsyncIndex Unsigned32, cnsInpSrcName SnmpAdminString, cnsInpSrcIntfType CiscoNetsyncIfType, cnsInpSrcPriority Unsigned32, cnsInpSrcESMCCap CiscoNetsyncESMCCap, cnsInpSrcSSMCap CiscoNetsyncSSMCap, cnsInpSrcQualityLevelTxCfg CiscoNetsyncQualityLevel, cnsInpSrcQualityLevelRxCfg CiscoNetsyncQualityLevel, cnsInpSrcQualityLevelTx CiscoNetsyncQualityLevel, cnsInpSrcQualityLevelRx CiscoNetsyncQualityLevel, cnsInpSrcQualityLevel CiscoNetsyncQualityLevel, cnsInpSrcHoldoffTime Unsigned32, cnsInpSrcWtrTime Unsigned32, cnsInpSrcLockout TruthValue, cnsInpSrcSignalFailure TruthValue, cnsInpSrcAlarm TruthValue, cnsInpSrcAlarmInfo CiscoNetsyncAlarmInfo, cnsInpSrcFSW TruthValue, cnsInpSrcMSW TruthValue } cnsInpSrcNetsyncIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index that uniquely represents an entry in this table. This index is assigned arbitrarily by the clock selection process and may not be persistent across reboots." ::= { cnsInputSourceEntry 1 } cnsInpSrcName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the name of an input clock source configured for the T0 clock selection." ::= { cnsInputSourceEntry 2 } cnsInpSrcIntfType OBJECT-TYPE SYNTAX CiscoNetsyncIfType MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the type of an input clock source configured for the T0 clock selection." ::= { cnsInputSourceEntry 3 } cnsInpSrcPriority OBJECT-TYPE SYNTAX Unsigned32 (1..1024) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the priority of an input clock source configured for the T0 clock selection. A smaller value represents a higher priority." REFERENCE "ITU-T standard G.781 section 5.10" ::= { cnsInputSourceEntry 4 } cnsInpSrcESMCCap OBJECT-TYPE SYNTAX CiscoNetsyncESMCCap MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the ESMC capability of an input clock source configured for the T0 clock selection. This is applicable only to Synchronous Ethernet input clock source identified by cnsInpSrcIntfType 'netsyncIfTypeEthernet'." ::= { cnsInputSourceEntry 5 } cnsInpSrcSSMCap OBJECT-TYPE SYNTAX CiscoNetsyncSSMCap MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the SSM capability of an input clock source configured for the T0 clock selection. This is applicable only to any synchronous interface clock source except SyncE interface, which is identified by cnsInpSrcIntfType 'netsyncIfTypeEthernet'." ::= { cnsInputSourceEntry 6 } cnsInpSrcQualityLevelTxCfg OBJECT-TYPE SYNTAX CiscoNetsyncQualityLevel MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the configured transmit clock quality level of an input clock source." ::= { cnsInputSourceEntry 7 } cnsInpSrcQualityLevelRxCfg OBJECT-TYPE SYNTAX CiscoNetsyncQualityLevel MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the configured receive clock quality level of an input clock source." ::= { cnsInputSourceEntry 8 } cnsInpSrcQualityLevelTx OBJECT-TYPE SYNTAX CiscoNetsyncQualityLevel MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the most recent clock quality level transmitted on the input clock source." ::= { cnsInputSourceEntry 9 } cnsInpSrcQualityLevelRx OBJECT-TYPE SYNTAX CiscoNetsyncQualityLevel MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the last clock quality level received on the input clock source." ::= { cnsInputSourceEntry 10 } cnsInpSrcQualityLevel OBJECT-TYPE SYNTAX CiscoNetsyncQualityLevel MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the current clock quality level of the input clock source. This is the effective quality which is derived from three values: 1) most recent clock quality level received, 2) forced clock quality level (entered via configuration) 3) overridden clock quality level as a result of line protocol down, signal failure, or alarms." ::= { cnsInputSourceEntry 11 } cnsInpSrcHoldoffTime OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the hold-off time value of an input clock source. The hold-off time prevents short activation of signal failure is passed to the selection process. When a signal failure event is reported on a clock source, it waits the duration of the hold-off time before declaring signal failure on the clock source." REFERENCE "ITU-T standard G.781 section 5.8" ::= { cnsInputSourceEntry 12 } cnsInpSrcWtrTime OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) UNITS "Seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the wait-to-restore time value of an input clock source. The wait-to-restore time ensures that a previous failed synchronization source is only again considered as available by the selection process if it is fault-free for a certain time. When a signal failure condition is cleared on a clock source, it waits the duration of the wait-to-restore time before clearing the signal failure status on the clock source." REFERENCE "ITU-T standard G.781 section 5.9" ::= { cnsInputSourceEntry 13 } cnsInpSrcLockout OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether or not the lockout command has been applied to a clock source. The 'true' value means the clock source is not considered by the selection process." REFERENCE "ITU-T standard G.781 section 5.11.1" ::= { cnsInputSourceEntry 14 } cnsInpSrcSignalFailure OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether or not a signal failure event is currently being reported on the input clock source." REFERENCE "ITU-T standard G.781 section 5.7" ::= { cnsInputSourceEntry 15 } cnsInpSrcAlarm OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether or not an alarm event is currently being reported on the input clock source." ::= { cnsInputSourceEntry 16 } cnsInpSrcAlarmInfo OBJECT-TYPE SYNTAX CiscoNetsyncAlarmInfo MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the alarm reasons of an input clock source if an alarm event is being reported on it." ::= { cnsInputSourceEntry 17 } cnsInpSrcFSW OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the forced switching flag. Forced switching, as described in G.781, is used to override the currently selected synchronization source. The 'true' value indicates the currently selected clock source is a result of the forced switching. The 'false' value indicates the currently selected clock source is not a result of forced switching." REFERENCE "ITU-T standard G.781 section 5.11.2.2" ::= { cnsInputSourceEntry 18 } cnsInpSrcMSW OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the manual switching flag. The 'true' value indicates the currently selected clock source is a result of the manual switching. The switch allows a user to select a synchronization source assuming it is enabled, not locked out, not in signal fail condition, and has a QL better than DNU in QL-enabled mode. A clock source is enabled when it occupies a row in cnsInputSourceTable. A clock source is not locked out when cnsInpSrcLockout contains the value 'false'. A clock source is not in signal failure condition when cnsInpSrcSignalFailure contains the value 'false'. The QL is identified in cnsInpSrcQualityLevel. In QL-enabled mode, a manual switch can be performed only to a source which has the highest available QL." REFERENCE "ITU-T standard G.781 section 5.11.2.3" ::= { cnsInputSourceEntry 19 } cnsExtOutputTable OBJECT-TYPE SYNTAX SEQUENCE OF CnsExtOutputEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "T4 external output table. This table contains a list of T4 external outputs. Each T4 external output is associated with clock source(s) to be found in cnsT4ClockSourceTable. The clock selection process considers all the available clock sources and select the T4 clock source based on the G.781 clock selection algorithm." ::= { ciscoNetsyncMIBTables 4 } cnsExtOutputEntry OBJECT-TYPE SYNTAX CnsExtOutputEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created in the table when a user adds a T4 external output in the configuration. A T4 external output configured input clock sources are defined in cnsT4ClockSourceTable. An entry is removed from the table when a user removes a T4 external output from the configuration." INDEX { cnsExtOutListIndex } ::= { cnsExtOutputTable 1 } CnsExtOutputEntry ::= SEQUENCE { cnsExtOutListIndex Unsigned32, cnsExtOutSelNetsyncIndex Unsigned32, cnsExtOutName SnmpAdminString, cnsExtOutIntfType CiscoNetsyncIfType, cnsExtOutQualityLevel CiscoNetsyncQualityLevel, cnsExtOutPriority Unsigned32, cnsExtOutFSW TruthValue, cnsExtOutMSW TruthValue, cnsExtOutSquelch TruthValue } cnsExtOutListIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index that uniquely represents an entry in this table. This index is assigned arbitrarily by the clock selection process and may not be persistent across reboots." ::= { cnsExtOutputEntry 1 } cnsExtOutSelNetsyncIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "An index that uniquely represents the selected input clock source whose information is reported by a row in cnsT4ClockSourceTable. The index lists the value of cnsT4ClkSrcNetsyncIndex, which is the input clock source of the T4 external output selected by the G.781 clock selection process." ::= { cnsExtOutputEntry 2 } cnsExtOutName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the name of a T4 external output." ::= { cnsExtOutputEntry 3 } cnsExtOutIntfType OBJECT-TYPE SYNTAX CiscoNetsyncIfType MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the interface type of the T4 external output." ::= { cnsExtOutputEntry 4 } cnsExtOutQualityLevel OBJECT-TYPE SYNTAX CiscoNetsyncQualityLevel MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the clock quality of the T4 external output." ::= { cnsExtOutputEntry 5 } cnsExtOutPriority OBJECT-TYPE SYNTAX Unsigned32 (1..1024) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the priority of the selected clock source for a T4 external output. A smaller value represents a higher priority." REFERENCE "ITU-T standard G.781 section 5.10" ::= { cnsExtOutputEntry 6 } cnsExtOutFSW OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the forced switching flag. Forced switching, as described in G.781, is used to override the currently selected synchronization source, The T4 selected synchronization source is identified by cnsExtOutSelNetsyncIndex, which contains the index to the clock source in cnsT4ClockSourceTable. The 'true' value indicates the currently selected T4 clock source is a result of the forced switching. The 'false' value indicates the currently selected T4 clock source is not a result of forced switching." REFERENCE "ITU-T standard G.781 section 5.11.2.2" ::= { cnsExtOutputEntry 7 } cnsExtOutMSW OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the manual switching flag. The 'true' value indicates the currently selected T4 clock source is a result of the manual switch command. The command allows a user to select a synchronization source assuming it is enabled, not locked out, not in signal fail condition, and has a QL better than DNU in QL-enabled mode. A clock source is enabled when it occupies in row in cnsT4ClockSourceTable. A clock source is not locked out when cnsT4ClkSrcLockout contains the value 'false'. A clock source is not in signal failure condition when cnsT4ClkSrcSignalFailure contains the value 'false'. The QL is identified in cnsT4ClkSrcQualityLevel. In QL-enabled mode, a manual switch can be performed only to a source which has the highest available QL." REFERENCE "ITU-T standard G.781 section 5.11.2.3" ::= { cnsExtOutputEntry 8 } cnsExtOutSquelch OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether or not a T4 external output is squelched. Squelching is a sychronization function defined to prevent transmission of a timing signal with a quality that is lower than the quality of the clock in the receiving networks element or SASE. It is also used for the prevention of timing loops." REFERENCE "ITU-T standard G.781 section 5.4.1.4" ::= { cnsExtOutputEntry 9 } cnsT4ClockSourceTable OBJECT-TYPE SYNTAX SEQUENCE OF CnsT4ClockSourceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "T4 clock source table. This table contains a list of input sources for a specific T4 external output. An entry shall be added to cnsExtOutputTable first. Then clock sources shall be added in this table for the selection process to select the appropriate T4 clock source." ::= { ciscoNetsyncMIBTables 5 } cnsT4ClockSourceEntry OBJECT-TYPE SYNTAX CnsT4ClockSourceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created in the table when a user adds a clock source to a T4 external output in the configuration. The T4 external output is defined in the T4 external output table. An entry is removed in the table when a user removes a T4 clock source from the configuration." INDEX { cnsExtOutListIndex, cnsT4ClkSrcNetsyncIndex } ::= { cnsT4ClockSourceTable 1 } CnsT4ClockSourceEntry ::= SEQUENCE { cnsT4ClkSrcNetsyncIndex Unsigned32, cnsT4ClkSrcName SnmpAdminString, cnsT4ClkSrcIntfType CiscoNetsyncIfType, cnsT4ClkSrcPriority Unsigned32, cnsT4ClkSrcESMCCap CiscoNetsyncESMCCap, cnsT4ClkSrcSSMCap CiscoNetsyncSSMCap, cnsT4ClkSrcQualityLevelTxCfg CiscoNetsyncQualityLevel, cnsT4ClkSrcQualityLevelRxCfg CiscoNetsyncQualityLevel, cnsT4ClkSrcQualityLevelTx CiscoNetsyncQualityLevel, cnsT4ClkSrcQualityLevelRx CiscoNetsyncQualityLevel, cnsT4ClkSrcQualityLevel CiscoNetsyncQualityLevel, cnsT4ClkSrcHoldoffTime Unsigned32, cnsT4ClkSrcWtrTime Unsigned32, cnsT4ClkSrcLockout TruthValue, cnsT4ClkSrcSignalFailure TruthValue, cnsT4ClkSrcAlarm TruthValue, cnsT4ClkSrcAlarmInfo CiscoNetsyncAlarmInfo, cnsT4ClkSrcFSW TruthValue, cnsT4ClkSrcMSW TruthValue } cnsT4ClkSrcNetsyncIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index that uniquely represents an entry in this table. This index is assigned arbitrarily by the clock selection process and may not be persistent across reboots." ::= { cnsT4ClockSourceEntry 1 } cnsT4ClkSrcName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the name of a input clock source configured for the T4 clock selection." ::= { cnsT4ClockSourceEntry 2 } cnsT4ClkSrcIntfType OBJECT-TYPE SYNTAX CiscoNetsyncIfType MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the type of an input clock source configured for the T4 clock selection." ::= { cnsT4ClockSourceEntry 3 } cnsT4ClkSrcPriority OBJECT-TYPE SYNTAX Unsigned32 (1..1024) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the priority of an input clock source configured for the T4 clock selection. A smaller value represents a higher priority." REFERENCE "ITU-T standard G.781 section 5.10" ::= { cnsT4ClockSourceEntry 4 } cnsT4ClkSrcESMCCap OBJECT-TYPE SYNTAX CiscoNetsyncESMCCap MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the ESMC capability of an input clock source configured for the T4 clock selection. This is applicable only to Synchronous Ethernet input clock source identified by cnsT4ClkSrcIntfType 'netsyncIfTypeEthernet'." ::= { cnsT4ClockSourceEntry 5 } cnsT4ClkSrcSSMCap OBJECT-TYPE SYNTAX CiscoNetsyncSSMCap MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the SSM capability of an input clock source configured for the T4 clock selection. This is applicable only to any synchronous interface clock source except SyncE interface, which is identified by cnsT4ClkSrcIntfType 'netsyncIfTypeEthernet'." ::= { cnsT4ClockSourceEntry 6 } cnsT4ClkSrcQualityLevelTxCfg OBJECT-TYPE SYNTAX CiscoNetsyncQualityLevel MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the configured transmit clock quality level of a T4 input clock source." ::= { cnsT4ClockSourceEntry 7 } cnsT4ClkSrcQualityLevelRxCfg OBJECT-TYPE SYNTAX CiscoNetsyncQualityLevel MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the configured receive clock quality level of a T4 input clock source." ::= { cnsT4ClockSourceEntry 8 } cnsT4ClkSrcQualityLevelTx OBJECT-TYPE SYNTAX CiscoNetsyncQualityLevel MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the most recent clock quality level transmitted on the T4 input clock source." ::= { cnsT4ClockSourceEntry 9 } cnsT4ClkSrcQualityLevelRx OBJECT-TYPE SYNTAX CiscoNetsyncQualityLevel MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the last clock quality level received on the T4 input clock source." ::= { cnsT4ClockSourceEntry 10 } cnsT4ClkSrcQualityLevel OBJECT-TYPE SYNTAX CiscoNetsyncQualityLevel MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the current clock quality level of the T4 input clock source. This is the effective quality which is derived from three values: 1) most recent clock quality level received, 2) forced clock quality level (entered via configuration) 3) overridden clock quality level as a result of line protocol down, signal failure, or alarms." ::= { cnsT4ClockSourceEntry 11 } cnsT4ClkSrcHoldoffTime OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the hold-off time value of a T4 input clock source. The hold-off time prevents short activation of signal failure is passed to the selection process. When a signal failure event is reported on a clock source, it waits the duration of the hold-off time before declaring signal failure on the clock source." REFERENCE "ITU-T standard G.781 section 5.8" ::= { cnsT4ClockSourceEntry 12 } cnsT4ClkSrcWtrTime OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the wait-to-restore time value of a T4 input clock source. The wait-to-restore time ensures that a previous failed synchronization source is only again considered as available by the selection process if it is fault-free for a certain time. When a signal failure condition is cleared on a clock source, it waits the duration of the wait-to-restore time before clearing the signal failure status on the clock source." REFERENCE "ITU-T standard G.781 section 5.9" ::= { cnsT4ClockSourceEntry 13 } cnsT4ClkSrcLockout OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether or not the lockout command has been applied on a T4 clock source. The 'true' value means the clock source is not considered by the selection process." REFERENCE "ITU-T standard G.781 section 5.11.1" ::= { cnsT4ClockSourceEntry 14 } cnsT4ClkSrcSignalFailure OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether or not a signal failure event is currently being reported on the T4 input clock source." REFERENCE "ITU-T standard G.781 section 5.7" ::= { cnsT4ClockSourceEntry 15 } cnsT4ClkSrcAlarm OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether or not an alarm event is currently being reported on the T4 input clock source." ::= { cnsT4ClockSourceEntry 16 } cnsT4ClkSrcAlarmInfo OBJECT-TYPE SYNTAX CiscoNetsyncAlarmInfo MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the alarm reasons of a T4 input clock source if an alarm event is being reported on the clock source." ::= { cnsT4ClockSourceEntry 17 } cnsT4ClkSrcFSW OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the forced switching flag. Forced switching, as described in G.781, is used to override the currently selected synchronization source. The 'true' value indicates the currently selected T4 clock source is a result of the forced switching. The 'false' value indicates the currently selected T4 clock source is not a result of forced switching." REFERENCE "ITU-T standard G.781 section 5.11.2.2" ::= { cnsT4ClockSourceEntry 18 } cnsT4ClkSrcMSW OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the manual switching flag. The 'true' value indicates the currently selected T4 clock source is a result of the manual switching. The switch allows a user to select a synchronization source assuming it is enabled, not locked out, not in signal fail condition, and has a QL better than DNU in QL-enabled mode. A clock source is enabled when it occupies a row in cnsT4ClockSourceTable. A clock source is not locked out when cnsT4ClkSrcLockout contains the value 'false'. A clock source is not in signal failure condition when cnsT4ClkSrcSignalFailure contains the value 'false'. The QL is identified in cnsT4ClkSrcQualityLevel. In QL-enabled mode, a manual switch can be performed only to a source which has the highest available QL." REFERENCE "ITU-T standard G.781 section 5.11.2.3" ::= { cnsT4ClockSourceEntry 19 } cnsNotifObjects OBJECT IDENTIFIER ::= { ciscoNetsyncMIBObjects 2 } cnsInpSrcFailClear OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the clear status of a signal failure event. A value of 'true' means a signal failure event reported on a clock source has been cleared. A value of 'false' means a signal event has been reported on a clock source." ::= { cnsNotifObjects 1 } cnsInpSrcAlarmClear OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the clear status of an alarm event. A value of 'true' means an alarm event reported on a clock source has been cleared. A value of 'false' means an alarm event has been reported on a clock source." ::= { cnsNotifObjects 2 } ciscoNetsyncMIBNotifControl OBJECT IDENTIFIER ::= { ciscoNetsyncMIBObjects 3 } cnsMIBEnableStatusNotification OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A control object to enable/disable ciscoNetsyncSelectedT0Clock, ciscoNetsyncSelectedT4Clock, ciscoNetsyncInputSignalFailureStatus, ciscoNetsyncInputAlarmStatus notifications at the system level. This object should hold any of the below values. true - The notif is enabled globally for the system false- The notif is disabled globally for the system" DEFVAL { false } ::= { ciscoNetsyncMIBNotifControl 1 } -- Default Notification Type ciscoNetsyncSelectedT0Clock NOTIFICATION-TYPE OBJECTS { cnsSelInpSrcName, cnsSelInpSrcIntfType, cnsSelInpSrcQualityLevel, cnsSelInpSrcPriority } STATUS current DESCRIPTION "T0 clock selection notification. This notification is generated when one of the following conditions is met: - A new clock source is selected by the T0 clock selection. - The clock quality of a T0 selected clock source is changed. - The configured priority of a T0 selected clock source is changed. " ::= { ciscoNetsyncMIBNotifs 1 } ciscoNetsyncSelectedT4Clock NOTIFICATION-TYPE OBJECTS { cnsExtOutName, cnsT4ClkSrcName, cnsT4ClkSrcIntfType, cnsT4ClkSrcQualityLevel, cnsT4ClkSrcPriority } STATUS current DESCRIPTION "T4 clock selection notification. This notification is generated when one of the following conditions is met: - A new clock source is selected by the T4 clock selection. - The clock quality of a T4 selected clock source is changed. - The configured priority of a T4 selected clock source is changed. " ::= { ciscoNetsyncMIBNotifs 2 } ciscoNetsyncInputSignalFailureStatus NOTIFICATION-TYPE OBJECTS { cnsInpSrcName, cnsInpSrcIntfType, cnsInpSrcFailClear } STATUS current DESCRIPTION "Input clock source signal failure notification. This notification is generated when a signal failure event is reported on an input clock source. One of the conditions a signal failure event could be due to interface shutdown." ::= { ciscoNetsyncMIBNotifs 3 } ciscoNetsyncInputAlarmStatus NOTIFICATION-TYPE OBJECTS { cnsInpSrcName, cnsInpSrcIntfType, cnsInpSrcAlarmInfo, cnsInpSrcAlarmClear } STATUS current DESCRIPTION "Input clock source alarm notification. This notification is generated when an alarm event is reported on an input clock source." ::= { ciscoNetsyncMIBNotifs 4 } ciscoNetsyncMIBCompliances OBJECT IDENTIFIER ::= { ciscoNetsyncMIBConform 1 } ciscoNetsyncMIBGroups OBJECT IDENTIFIER ::= { ciscoNetsyncMIBConform 2 } ciscoNetsyncMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "This is a default module-compliance containing default object groups." MODULE -- this module MANDATORY-GROUPS { cnsClkSelGlobalObjectGroup, cnsSelectedInputSourceObjectGroup, cnsInputSourceObjectGroup, cnsExtOutputObjectGroup, cnsT4ClkSrcObjectGroup, ciscoNetsyncMIBNotificationGroup, cnsMIBNotifEnablesGroup } ::= { ciscoNetsyncMIBCompliances 1 } -- Units of Conformance cnsClkSelGlobalObjectGroup OBJECT-GROUP OBJECTS { cnsClkSelGlobProcessMode, cnsClkSelGlobClockMode, cnsClkSelGlobNetsyncEnable, cnsClkSelGlobRevertiveMode, cnsClkSelGlobESMCMode, cnsClkSelGlobEECOption, cnsClkSelGlobNetworkOption, cnsClkSelGlobHoldoffTime, cnsClkSelGlobWtrTime, cnsClkSelGlobNofSources, cnsClkSelGlobLastHoldoverSeconds, cnsClkSelGlobCurrHoldoverSeconds } STATUS current DESCRIPTION "This group contains all objects referenced by the G.781 clock selection process table." ::= { ciscoNetsyncMIBGroups 1 } cnsSelectedInputSourceObjectGroup OBJECT-GROUP OBJECTS { cnsSelInpSrcName, cnsSelInpSrcQualityLevel, cnsSelInpSrcTimestamp, cnsSelInpSrcFSW, cnsSelInpSrcMSW, cnsSelInpSrcIntfType, cnsSelInpSrcPriority } STATUS current DESCRIPTION "This group contains all objects referenced by cnsSelectedInputSourceTable." ::= { ciscoNetsyncMIBGroups 2 } cnsInputSourceObjectGroup OBJECT-GROUP OBJECTS { cnsInpSrcName, cnsInpSrcIntfType, cnsInpSrcPriority, cnsInpSrcESMCCap, cnsInpSrcSSMCap, cnsInpSrcQualityLevelTxCfg, cnsInpSrcQualityLevelRxCfg, cnsInpSrcQualityLevelTx, cnsInpSrcQualityLevelRx, cnsInpSrcQualityLevel, cnsInpSrcHoldoffTime, cnsInpSrcWtrTime, cnsInpSrcLockout, cnsInpSrcSignalFailure, cnsInpSrcAlarm, cnsInpSrcAlarmInfo, cnsInpSrcFSW, cnsInpSrcMSW, cnsInpSrcAlarmClear, cnsInpSrcFailClear } STATUS current DESCRIPTION "This group contains all objects referenced by cnsInputSourceTable." ::= { ciscoNetsyncMIBGroups 3 } cnsExtOutputObjectGroup OBJECT-GROUP OBJECTS { cnsExtOutName, cnsExtOutSelNetsyncIndex, cnsExtOutIntfType, cnsExtOutQualityLevel, cnsExtOutPriority, cnsExtOutFSW, cnsExtOutMSW, cnsExtOutSquelch } STATUS current DESCRIPTION "This group contains all objects referenced by cnsExtOutputTable." ::= { ciscoNetsyncMIBGroups 4 } cnsT4ClkSrcObjectGroup OBJECT-GROUP OBJECTS { cnsT4ClkSrcName, cnsT4ClkSrcIntfType, cnsT4ClkSrcPriority, cnsT4ClkSrcESMCCap, cnsT4ClkSrcSSMCap, cnsT4ClkSrcQualityLevelTxCfg, cnsT4ClkSrcQualityLevelRxCfg, cnsT4ClkSrcQualityLevelTx, cnsT4ClkSrcQualityLevelRx, cnsT4ClkSrcQualityLevel, cnsT4ClkSrcHoldoffTime, cnsT4ClkSrcWtrTime, cnsT4ClkSrcLockout, cnsT4ClkSrcSignalFailure, cnsT4ClkSrcAlarm, cnsT4ClkSrcAlarmInfo, cnsT4ClkSrcFSW, cnsT4ClkSrcMSW } STATUS current DESCRIPTION "This group contains all objects referenced by cnsT4ClockSourceTable." ::= { ciscoNetsyncMIBGroups 5 } cnsMIBNotifEnablesGroup OBJECT-GROUP OBJECTS { cnsMIBEnableStatusNotification } STATUS current DESCRIPTION "The collection of objects which are used to enable notification. " ::= { ciscoNetsyncMIBGroups 6 } ciscoNetsyncMIBNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { ciscoNetsyncSelectedT0Clock, ciscoNetsyncSelectedT4Clock, ciscoNetsyncInputSignalFailureStatus, ciscoNetsyncInputAlarmStatus } STATUS current DESCRIPTION "The is the netsync notification group." ::= { ciscoNetsyncMIBGroups 7 } END