-- ***************************************************************** -- CISCO-MGX82XX-DSX3-MIB: DS3/E3 interface MIB for MGX82xx products. -- -- January 2003, Jyotsna Gummaraju -- December 2002, Subra Hegde -- -- Copyright (c) 2002 by cisco Systems, Inc. -- All rights reserved. -- ***************************************************************** CISCO-MGX82XX-DSX3-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Counter32, Integer32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF DisplayString FROM SNMPv2-TC dsx3Line,dsx3Framing FROM BASIS-MIB ciscoWan FROM CISCOWAN-SMI; ciscoMgx82xxDsx3MIB MODULE-IDENTITY LAST-UPDATED "200301110000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-wanatm@cisco.com" DESCRIPTION "The MIB Module for DS3/E3 interface configuration , statistics and Alarm configuration. This MIB is supported in T3/E3 service modules in MGX products. Some of the T3/E3 service modules(Cards) are: PXM1 : Processor Switch Module. CESM-T3E3: Circuit Emulation Service Module FRSM-VHS : Frame Relay Service Module. Includes T3 and Channelized T3 categories. FRSM-2CT3: Channelized FRSM Module SRM-3T3 : Service Resource Module Terminologies Used : SDH : SONET Digital Hierarchy PLCP : Physical Layer Convergence Procedure. BERT : Bit Error Rate Testing. FEAC : Far End Alarm Code. OOF : Out Of Frame. AIS : Alarm Indication Signal. LOF : Loss Of Frame. RAI : Remote Alarm Indication. HCS : Header Check Sequence HEC : Header Error Control MA byte : Maintenance and Adaptation byte Tx MA Byte: This is explained in ITU-T G.832 This Byte contains following fields: Payload type Payload dependent bits Timing maker bit Rx MA Byte: This is explained in ITU-T G.832 This Byte contains following fields: Payload type Timing maker bit " REVISION "200301110000Z" DESCRIPTION "Initial version of the MIB. The content of this MIB was originally available in CISCO-WAN-AXIPOP-MIB defined using SMIv1. The applicable objects from CISCO-WAN-AXIPOP-MIB are defined using SMIv2 in this MIB. Also the descriptions of some of the objects have been modified." ::= { ciscoWan 59 } dsx3Config OBJECT IDENTIFIER ::= { dsx3Line 1 } dsx3AlarmConfig OBJECT IDENTIFIER ::= { dsx3Line 2 } dsx3Alarm OBJECT IDENTIFIER ::= { dsx3Line 3 } dsx3Counter OBJECT IDENTIFIER ::= { dsx3Line 4 } dsx3PlcpConfig OBJECT IDENTIFIER ::= { dsx3Framing 1 } dsx3PlcpAlarmConfig OBJECT IDENTIFIER ::= { dsx3Framing 2 } dsx3PlcpAlarm OBJECT IDENTIFIER ::= { dsx3Framing 3 } dsx3PlcpCounter OBJECT IDENTIFIER ::= { dsx3Framing 4 } -- -------------------------------------------------------------- -- -- dsx3Config group -- This group contains dsx3 line configuration table -- -- -------------------------------------------------------------- cwDsx3ConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF CwDsx3ConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The DS3/E3 Configuration table. There is one row for each DSX3 port in the system. The table size (number of rows) is given by the value of dsx3LineNumOfValidEntries." ::= { dsx3Config 1 } cwDsx3ConfigEntry OBJECT-TYPE SYNTAX CwDsx3ConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the DSX3 Configuration table." INDEX { dsx3LineNum } ::= { cwDsx3ConfigTable 1 } CwDsx3ConfigEntry ::= SEQUENCE { dsx3LineNum Integer32, cwDsx3LineType INTEGER, cwDsx3LineCoding INTEGER, cwDsx3LineLength INTEGER, dsx3LineOOFCriteria INTEGER, dsx3LineAIScBitsCheck INTEGER, dsx3LineLoopbackCommand INTEGER, dsx3LineRcvFEACValidation INTEGER, dsx3LineXmtFEACCode INTEGER, dsx3LineBERTEnable INTEGER, dsx3LineBERTPattern INTEGER, dsx3LineBERTResult INTEGER, dsx3BERTResultClrButton INTEGER, dsx3TrailTraceOption INTEGER, dsx3TxTrailTrace DisplayString, dsx3RxTrailTrace DisplayString, dsx3TxTimingMarker INTEGER, dsx3RxTimingMarker INTEGER, dsx3TxPayloadType INTEGER, dsx3RxPayloadType INTEGER, dsx3TxTumf Integer32, dsx3RxTumf Integer32, dsx3LineEnable INTEGER, dsx3FarEndLoopbkLineNum INTEGER, dsx3LineXmtClockSrc INTEGER, dsx3FarEndLoopbkLineStatus Integer32, dsx3LineEqualizer INTEGER, dsx3NearEndLoopbkLineStatus Integer32, dsx3SubRateEnable INTEGER, dsx3DsuSelect INTEGER, dsx3LineRate Integer32, dsx3LineScrambleEnable INTEGER } dsx3LineNum OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object is the identifier of a DS3/E3 Interface on a managed device. The range supported depends upon the type of the card(controller card, service module). For 1 port Card : Range is 1..1 Example : CESM-T3E3 For 2 Port Card : Range is 1..2 Example : PXM1-2T3E3. For 3 Port Card : Range is 1..3 Example: SRM-3T3" ::= { cwDsx3ConfigEntry 1 } cwDsx3LineType OBJECT-TYPE SYNTAX INTEGER { dsx3CbitParity (1), g832-g804 (2), dsx3M23 (3), g751 (4), dsx3Unframed (5), e3Unframed (6) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable indicates the variety of DS3 C-bit or E3 application implementing this interface. The type of interface affects the interpretation of the usage and error statistics. The rate of DS3 is 44.736 Mbps and E3 is 34.368 Mbps. The values, in sequence, describe: TITLE: SPECIFICATION: dsx3CbitParity ANSI T1.107a-1990 [9a] g832-g804 ITU-T G.832, G.804 dsx3M23 ANSI T1.107-1988 [9] g751 ITU-T G.751 CESM-T3 supports only ds3Unframed linetype. CESM-E3 supports only e3Unframed linetype." ::= { cwDsx3ConfigEntry 2 } cwDsx3LineCoding OBJECT-TYPE SYNTAX INTEGER { dsx3B3ZS (1), e3HDB3 (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable describes the variety of Zero Code Suppression used on this interface, which in turn affects a number of its characteristics. dsx3B3ZS and e3HDB3 refer to the use of specified patterns of normal bits and bipolar violations which are used to replace sequences of zero bits of a specified length. dsx3B3ZS(1) : Bipolar 3-Zero Substitution(B3ZS) suppression. e3HDB3 (2) : High-Density Bipolar 3(HDB3) suppression." ::= { cwDsx3ConfigEntry 3 } cwDsx3LineLength OBJECT-TYPE SYNTAX INTEGER { lessThan225(1), moreThan225(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the length of the DS3 Line. This object provides information for line build out circuitry if it exists and can use this object to adjust the line build out." ::= { cwDsx3ConfigEntry 4 } dsx3LineOOFCriteria OBJECT-TYPE SYNTAX INTEGER { fBits3Of8 (1), fBits3Of16 (2), notApplicable(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the out of frame decision criteria. OOF is declared when errors are detected in the framing octets for four consecuitive frames. fBits3Of8(1) : an OOF condition is declared if at least 3 of 8 framing bits are in error. fBits3Of16(2): an OOF is declared if 3 of 16 framing bits are found to be in error. notApplicable(3) : used in case where it is not applicable. This value can not be set. This object is not applicable when cwDsx3LineType is set to g832-g804(2) or g751(4). This object is not applicable for CESM-T3/E3" ::= { cwDsx3ConfigEntry 5 } dsx3LineAIScBitsCheck OBJECT-TYPE SYNTAX INTEGER { checkCbits(1), ignorebits(2), notApplicable(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "If check C-Bits options is chosen then AIS is declared when 1010 pattern is found and C-Bits are all zero. In the other case an AIS condition is declared when the AIS pattern 1010... is detected irrespective of the state of the C Bits. This object does not apply to the E3 interface. The value notApplicable(3) is used in case of interfaces where this object is not applicable. This object is not applicable for CESM-T3/E3." ::= { cwDsx3ConfigEntry 6 } dsx3LineLoopbackCommand OBJECT-TYPE SYNTAX INTEGER { dsx3NoLoop(1), dsx3RemoteLineLoop(2), dsx3LocalLineLoop(3), dsx3InbndLocalLoopback(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable represents the loopback configuration of the DS3/E3 interface. The values mean: dsx3NoLoop Not in the loopback state. A device that is not capable of performing a loopback on the interface shall always return this as it's value. dsx3RemoteLineLoop Near End loops back Remote data dsx3LocalLineLoop Near End loops back Local data(outbound). dsx3InboundLoopback Near End in bound loopback Local data(inbound)." ::= { cwDsx3ConfigEntry 7 } dsx3LineRcvFEACValidation OBJECT-TYPE SYNTAX INTEGER{ fFEACCodes4Of5 (1), fFEACCodes8Of10 (2), fFEACCodesDisable (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This entry specifies the FEAC code validation criteria. fFEACCodes4Of5(1) : a valid FEAC code is declared if 4 of 5 codes match. fFEACCodes8Of10(2): a valid FEAC code is declared if 8 of 10 codes match. fFEACCodesDisable(3) : Do not respond to any valid FEAC code. This object is not applicable to E3 interface. This object is not supported in CESM-T3/E3." ::= { cwDsx3ConfigEntry 8 } dsx3LineXmtFEACCode OBJECT-TYPE SYNTAX INTEGER { dsx3SendNoCode(1), dsx3SendLineCode(2), dsx3SendPayloadCode(3), dsx3SendResetCode(4), dsx3SendDS1LoopCode(5), dsx3SendTestPattern(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable indicates what bit-oriented code to transmit over the far-end alarm and control (FEAC) channel. The values mean: dsx3SendNoCode sending looped or normal data dsx3SendLineCode sending a request for a line loopback dsx3SendPayloadCode sending a request for a payload loopback (i.e., all DS1/E1s in a DS3/E3 frame) dsx3SendResetCode sending a loopback deactivation request. dsx3SendDS1LoopCode sending a request to put part of DS1/E1 within T3/E3 respectively into loopback. dsx3SendTestPattern sending a test pattern. This object is not applicable for CESM-T3/E3" ::= { cwDsx3ConfigEntry 9 } dsx3LineBERTEnable OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object enables/disables the BERT function on an interface. The possible values are : disabled(1): disables port BERT functionality enabled (2): enables port BERT functionality. value specified in dsx3LineBERTPattern is transmitted over the interface. The far end may be looped back and the test pattern verified." ::= { cwDsx3ConfigEntry 10 } dsx3LineBERTPattern OBJECT-TYPE SYNTAX INTEGER { allZero(1), allOnes(2), alternateOneZero(3), doubleOneZero(4), userOneWord(5), userTwoWords(6), userThreeWords(7), userFourWords(8), pattern2p15minus1(9), pattern2p20minus1(10), pattern2p23minus1(11) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object defines the test bit pattern to be used for BERT. The possible values are : Repetitive Patterns allZero(1): All Zeroes(Continuous spaces). This is repeating pattern of zeros(...000...). The use of this pattern is to test and verify that the ones density policing mechanism is functioning properly. This pattern must be used in circuits optioned for B8ZS. allOnes(2): All Ones(Continuous Marks). This is repeating pattern of ones(...1111...). This provides testing of maximum power level requirements. The all one pattern test causes the repeater to consume the maximum amount of power. If there is insufficient DC span power then the repeater may begin to fail. Typically this pattern is used for a simple continuity check. It may also be used to detect the presence of unwanted loop in the network. alternateOneZero(3): Alternate one/zero pattern(..1010..). This pattern produces a 50% ones density. It is used to stress the repeater's DC power consumption. doubleOneZero(4): Double alternate one/zero(..1100..). userOneWord(5), userTwoWords(6), userThreeWords(7), userFourWords(8), pattern2p15minus1(9) : This is the 2^15-1(32767 bit length) pattern as specified in ITU O.151. It has the maximum of 15(inverted) sequential zeros. This sequence is primarily intended for error and jitter measurements at bit rates of 1544, 2048, 6312, 8448, 32064 and 44736 kbit/s. pattern2p20minus1(10): This is the 2^20-1(1048575 bits in length) pattern specified in ITU O.153.It has the maximum of 19(non-inverted) sequential zeros. This pattern is primarily intended for error measurements at bit rates up to 73kbit/s. This pattern stresses the equalization and timing recovery circuitry of line repeaters. pattern2p23minus1(11): This is the 2^23-1(1048575 bits in length) pattern." ::= { cwDsx3ConfigEntry 11 } dsx3LineBERTResult OBJECT-TYPE SYNTAX INTEGER { bertFailed(1), bertPassed(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Result of BERT Test. The value in this object is not applicable if dsx3LineBERTEnable is set to disabled(1)." ::= { cwDsx3ConfigEntry 12 } dsx3BERTResultClrButton OBJECT-TYPE SYNTAX INTEGER { noAction(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to clear(2) causes the BERT result field to get cleared." ::= { cwDsx3ConfigEntry 13 } -- -- The following are the E3 specific configuration parameters -- dsx3TrailTraceOption OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used for enabling/disabling G.832 Trail Trace. The trail trace is used to repetitively transmit a trail access point identifier so that a trail receiving terminal can verify its continued connection to the intended transmitter. It uses a 16-byte numbering format (see Rec E.164). The first byte of the string is a frame start marker and includes the result of a CRC-7 calculation over the previous frame. The value of this object is set to disable(1) in case of cards where this feature is not supported. This object is not applicable for FRSM-VHS and CESM-T3/E3." REFERENCE "ITU-T G.832" ::= { cwDsx3ConfigEntry 14 } dsx3TxTrailTrace OBJECT-TYPE SYNTAX DisplayString (SIZE (1..15)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used for specifying the data to be used for G.832 Trail Trace ID/String. This object is applicable only for E3 interfaces with G.832 framing. The trail trace ID is a 16 octet field that contains 1 octet of CRC-7(first octet) and 15 octets of data. The CRC-7 is automatically calculated by the system(card supporting this feature). The format of the value is: Frame Start Marker Error(HEX): CRC-7 Bytes 2-6 (ASCII) [Byte 1-5 of this object] Bytes 7-11 (ASCII) [Byte 6-10 of this object] Bytes 12-16 (ASCII) [Byte 11-15 of this object] This object is not applicable for FRSM-VHS and CESM-T3/E3." REFERENCE "ITU-T G.832" ::= { cwDsx3ConfigEntry 15 } dsx3RxTrailTrace OBJECT-TYPE SYNTAX DisplayString (SIZE (1..15)) MAX-ACCESS read-only STATUS current DESCRIPTION "Received G.832 Trail Trace string. The format of the value is: First byte indicates CRC-7(frame start marker). Bytes 2-6 (ASCII) [Byte 1-5 of this object] Bytes 7-11 (ASCII) [Byte 6-10 of this object] Bytes 12-16 (ASCII) [Byte 11-15 of this object] The value of all zeroes indicates bad CRC-7. This object is not applicable for FRSM-VHS and CESM-T3/E3." REFERENCE "ITU-T G.832" ::= { cwDsx3ConfigEntry 16 } dsx3TxTimingMarker OBJECT-TYPE SYNTAX INTEGER { traceable (1), untraceable (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Transmitted timing marker bit in G.832 MA byte. This object can be set to traceable(1) to indicate that the timing source is traceable to a primary reference clock and is otherwise set to untraceable(2). This is always set to untraceable(2) in case of card where this feature is not supported. This feature is not supported in FRSM-VHS and CESM-T3/E3." REFERENCE "ITU-T G.832" ::= { cwDsx3ConfigEntry 17 } dsx3RxTimingMarker OBJECT-TYPE SYNTAX INTEGER { traceable (1), untraceable (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Received timing marker bit in G.832 MA byte. This object can be set to traceable(1) to indicate that the timing source is tracable to a primary reference clock and is otherwise set to untraceable(2). This is always set to untraceable(2) in case of card where this feature is not supported. This feature is not supported in FRSM-VHS and CESM-T3/E3." REFERENCE "ITU-T G.832" ::= { cwDsx3ConfigEntry 18 } dsx3TxPayloadType OBJECT-TYPE SYNTAX INTEGER { unequipped (1), equipped (2), atm (3), sdhtu12s (4) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the G.832 payload type for transmit data. The possible values are : unequipped (1): not carrying any payload equipped (2): Equipped,non-specific atm (3): ATM sdhtu12s (4): SDH Elements mapping It is recommended that this object is not instantiated in case of cards which does not support G.832 functionality. This is not supported in FRSM-VHS and CESM-T3/E3" REFERENCE "ITU-T G.832 section 2.1.2." DEFVAL { unequipped } ::= { cwDsx3ConfigEntry 19 } dsx3RxPayloadType OBJECT-TYPE SYNTAX INTEGER { unequipped (1), equipped (2), atm (3), sdhtu12s (4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Received payload type field in G.832 byte The possible values are : unequipped (1): not carrying any payload equipped (2): Equipped,non-specific atm (3): ATM sdhtu12s (4): SDH Elements mapping It is recommended that this object is not instantiated in case of cards which does not support G.832 functionality. This is not supported in FRSM-VHS and CESM-T3/E3" REFERENCE "ITU-T G.832 section 2.1.2." ::= { cwDsx3ConfigEntry 20 } dsx3TxTumf OBJECT-TYPE SYNTAX Integer32 (0..3) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the value of Tributary Multiframe Indicator(bits 6 and 7 of MA byte) in case of TU-1xs mapping. This is not supported in FRSM-VHS and CESM-T3/E3." REFERENCE "ITU-T G.832, section 3.4.3" ::= { cwDsx3ConfigEntry 21 } dsx3RxTumf OBJECT-TYPE SYNTAX Integer32 (0..3) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the value of Tributary Multiframe Indicator(bits 6 and 7 of MA byte) in case of TU-1xs mapping. This object is not supported in FRSM-VHS and CESM-T3/E3." REFERENCE "ITU-T G.832, section 3.4.3" ::= { cwDsx3ConfigEntry 22 } dsx3LineEnable OBJECT-TYPE SYNTAX INTEGER { disable (1), enable (2), modify (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used for enabling/disabling an interface and modifying the interface configuration. The possible values are: disable (1): Interface is administratively down enable (2): Interface is administratively up. modify (3): Used for modifying the parameters of an interface that has been already enabled(administratively up). To modify the parameters of this table, the value of this object must be set to enable(2) or modify(3)." ::= { cwDsx3ConfigEntry 23 } dsx3FarEndLoopbkLineNum OBJECT-TYPE SYNTAX INTEGER { ds1line1(1), ds1line2(2), ds1line3(3), ds1line4(4), ds1line5(5), ds1line6(6), ds1line7(7), ds1line8(8), ds1line9(9), ds1line10(10), ds1line11(11), ds1line12(12), ds1line13(13), ds1line14(14), ds1line15(15), ds1line16(16), ds1line17(17), ds1line18(18), ds1line19(19), ds1line20(20), ds1line21(21), ds1line22(22), ds1line23(23), ds1line24(24), ds1line25(25), ds1line26(26), ds1line27(27), ds1line28(28), ds1line29(29), ds3line(30) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specify which DS1 or DS3 line in the far-end for the loopback testing. For CESM-T3/E3, only ds3line(30) is valid." ::= { cwDsx3ConfigEntry 24 } dsx3LineXmtClockSrc OBJECT-TYPE SYNTAX INTEGER { backplaneClk (1), recoverClk (2), localClk (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The source of the transmit clock. backplaneClk(2) : clock source is from the backplane. recoverClk (3) : clock source is derived from another t3 interface. localClk (4) : clock source is from a local oscillator on the card" ::= { cwDsx3ConfigEntry 25 } dsx3FarEndLoopbkLineStatus OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This is a bitmap of the DSX3 FarEnd line loopback status bits Bit Position Loopback indicator ----------- ----- 1 DS1 Line 1 2 DS1 Line 2 3 DS1 Line 3 4 DS1 Line 4 5 DS1 Line 5 6 DS1 Line 6 7 DS1 Line 7 8 DS1 Line 8 9 DS1 Line 9 10 DS1 Line 10 11 DS1 Line 11 12 DS1 Line 12 ... ... ... 28 DS1 Line 28 29 all DS1 Lines 30 DSX3 For CESM-T3/E3, only DSX3 bit (bit 30) is valid." ::= { cwDsx3ConfigEntry 26 } dsx3LineEqualizer OBJECT-TYPE SYNTAX INTEGER { intrnlequalizer(1), extequalizer(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether the internal equalizer is being used or bypassed. Set this value depending on the line equipment to which the receiver is attached. intrnlequalizer(1): Use internal line equalizer extequalizer(2) : Use External equalizer or bypass internal equalizer." ::= { cwDsx3ConfigEntry 27 } dsx3NearEndLoopbkLineStatus OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This is a bitmap of the DSX3 NearEnd line loopback status bits BitPosition Loopback indicator ----------- ----- 1 DS1 Line 1 2 DS1 Line 2 3 DS1 Line 3 4 DS1 Line 4 5 DS1 Line 5 6 DS1 Line 6 7 DS1 Line 7 8 DS1 Line 8 9 DS1 Line 9 10 DS1 Line 10 11 DS1 Line 11 12 DS1 Line 12 ... ... ... 28 DS1 Line 28 29 DS1 Line 29 30 DSX3 For CESM-T3/E3, only DSX3 bit (bit 30) is valid." ::= { cwDsx3ConfigEntry 28 } dsx3SubRateEnable OBJECT-TYPE SYNTAX INTEGER { disable (1), enable (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable controls whether the DS3 subrates are enabled or not. The DS3 subrate is part of DSU functionality. This object is currently supported only in FRSM-VHS cards. It is recommended that this object is not instantiated in case of cards which does not support DSU functionality." DEFVAL { disable } ::= { cwDsx3ConfigEntry 29 } dsx3DsuSelect OBJECT-TYPE SYNTAX INTEGER { dl3100Mode(1), adcKentroxMode(2), larsCom(3), clearChannel(4), dsuAlgorithm2(5), dsuAlgorithm3(6), dsuAlgorithm4(7), dsuAlgorithm5(8) } MAX-ACCESS read-write STATUS current DESCRIPTION "The dsx3DsuSelect variable controls the type of DSU mode to be selected. The 'dsx3SubRateEnable' has to be set to 'enable' before selecting the mode in 'dsx3DsuSelect'. The possible values for this are : dl3100Mode - Indicates compatibility with Digital Link Inc's DL3100 DSU mode of operation. This mode permits line rates to be in multiples of 300 Kbps. adcKentroxMode - Indicates compatibility with ADC Kentrox's DSU. This mode permits line rates to be in multiples of 500 Kbps. larsCom - Indicates compatability with LarsCom DSU. clearChannel - Indicates the standard G.751 framing format (12 overhead bits and 1524 data bits in an E3 frame).This option is supported only in FRSM-2E3. dsuAlgorithm1 - dsuAlgorith4 - Presently this is not used in any of the cards. This object is supported only in FRSM-VHS cards. It is recommended that this object is not instantiated in case of cards which does not support DSU functionality." DEFVAL { dl3100Mode } ::= { cwDsx3ConfigEntry 30 } dsx3LineRate OBJECT-TYPE SYNTAX Integer32 (300..44736) UNITS "kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "The desired line rate when 'dsx3SubRateEnable' is enabled. If dsx3DsuSelect is set to 'dl3100Mode', the line rate can be configured in steps of 300 Kbps. If dsx3DsuSelect is set to 'adcKentroxMode', the line rate can be configured in steps of 500 Kbps. This object is supported only in FRSM-VHS cards. It is recommended that this object is not instantiated in case of cards which does not support DSU functionality." ::= { cwDsx3ConfigEntry 31 } dsx3LineScrambleEnable OBJECT-TYPE SYNTAX INTEGER { disabled (1), enabled (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable turns the scrambling feature ON/OFF The scrambling is a technique that enables framing to be maintained on certain medium-speed edge and trunk interfaces. This object is ONLY applicable for FRSM-2T3/E3." ::= { cwDsx3ConfigEntry 32 } dsx3LineNumOfValidEntries OBJECT-TYPE SYNTAX Integer32(0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of DSX3 configuration entries (regardless of their current configuration) in the cwDsx3ConfigTable." ::= { dsx3Config 2 } -- -------------------------------------------------------------- -- -- dsx3AlarmConfig group -- -- -------------------------------------------------------------- dsx3AlarmConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF Dsx3AlarmConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The DSX3 interface alarm configuration table. This table contains the parameters associated with detecting and declaring alarms for the interface. The parameters include severity of alarm, alarm integration parameters and 15 minute and 24 hour thresholds. The number of rows is given by dsx3LineNumOfValidEntries." ::= { dsx3AlarmConfig 1 } dsx3AlarmConfigEntry OBJECT-TYPE SYNTAX Dsx3AlarmConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the DSX3 Alarm Configuration table. Thresholds may be configured for: Line Code Violations (LCV), LineErrored Seconds (LES), Line Severely Errored Seconds (LSES), P-bit Coding Violations (PCV), P-bit Errored Seconds (PES), P-bit Severely Errored Seconds(PSES), Severely Errored Seconds (SES), Severely Errored Framing Seconds(SEFS), Unavailable Seconds (UAS), C-bit coding violations (CCV), C-bit errored seconds (CES), C-bit errored seconds (CSES). Once these thresholds are exceeded, minor or major alarms are raised. Please refer to RFC2496 for descriptions of these errors." INDEX { dsx3LineNum } ::= { dsx3AlarmConfigTable 1 } Dsx3AlarmConfigEntry ::= SEQUENCE { dsx3RedSeverity INTEGER, dsx3RAISeverity INTEGER, dsx3NEAlarmUpCount Integer32, dsx3NEAlarmDownCount Integer32, dsx3NEAlarmThreshold Integer32, dsx3FEAlarmUpCount Integer32, dsx3FEAlarmDownCount Integer32, dsx3FEAlarmThreshold Integer32, dsx3StatisticalAlarmSeverity INTEGER, dsx3LCV15MinThreshold Integer32, dsx3LCV24HrThreshold Integer32, dsx3LES15MinThreshold Integer32, dsx3LES24HrThreshold Integer32, dsx3LSES15MinThreshold Integer32, dsx3LSES24HrThreshold Integer32, dsx3PCV15MinThreshold Integer32, dsx3PCV24HrThreshold Integer32, dsx3PES15MinThreshold Integer32, dsx3PES24HrThreshold Integer32, dsx3PSES15MinThreshold Integer32, dsx3PSES24HrThreshold Integer32, dsx3SEFS15MinThreshold Integer32, dsx3SEFS24HrThreshold Integer32, dsx3AISS15MinThreshold Integer32, dsx3AISS24HrThreshold Integer32, dsx3UAS15MinThreshold Integer32, dsx3UAS24HrThreshold Integer32, dsx3E3BIP8CV15MinThreshold Integer32, dsx3E3BIP8CV24HrThreshold Integer32, dsx3E3BIP8ES15MinThreshold Integer32, dsx3E3BIP8ES24HrThreshold Integer32, dsx3E3BIP8SES15MinThreshold Integer32, dsx3E3BIP8SES24HrThreshold Integer32, dsx3CCV15MinThreshold Integer32, dsx3CCV24HrThreshold Integer32, dsx3CES15MinThreshold Integer32, dsx3CES24HrThreshold Integer32, dsx3CSES15MinThreshold Integer32, dsx3CSES24HrThreshold Integer32 } dsx3RedSeverity OBJECT-TYPE SYNTAX INTEGER { minor(1), major(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable is used to setup the severity of RED alarm. So when LOS/LOF alarm is detected the card will send the alarm with appropriate severity status. A major alarm will cause audible notification and the MAJOR ALARM LED will be turned ON. A minor alarm will just turn on the MINOR ALARM LED. LOF detection is not applicable for CESM-8T3/E3. " ::= { dsx3AlarmConfigEntry 1 } dsx3RAISeverity OBJECT-TYPE SYNTAX INTEGER { minor(1), major(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable is used to setup the severity of RAI alarm. So when RAI alarm is detected the card will send the alarm with appropriate severity status. A major alarm will cause the audible notification and the MAJOR ALARM LED will be turned ON. A minor alarm will just turn on the MINOR ALARM LED. This is not applicable for CESM-T3/E3. " ::= { dsx3AlarmConfigEntry 2 } dsx3NEAlarmUpCount OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "This parameter specifies the increment to the Near End alarm integration counters. The local alarms are LOS and LOF. The Default value is 6 and the integration counter is incremented by this value every 10 ms while the alarm persists. The counter is decremented by the value of dsx3NEAlarmDnCount while there is no alarm (the counter does not decrement below zero). When the integration counter exceeds dsx3NEAlarmThreshold an Alarm of the severity specified for the particular NE alarm is declared. LOF detection is not applicable for CESM-T3/E3" ::= { dsx3AlarmConfigEntry 3 } dsx3NEAlarmDownCount OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "This parameter specifies the decrement to the Near End alarm integration counters. The local alarms are LOS and LOF. The Default value is 1 and the integration counter is decremented by this value every 10 ms while no alarm persists. The counter is incremented by the value of dsx3NEAlarmUpCount while there is no alarm (the counter does not decrement below zero). When the integration counter reaches zero any Alarm previously declared is removed. LOF detection is not applicable for CESM-T3/E3" ::= { dsx3AlarmConfigEntry 4 } dsx3NEAlarmThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value that the alarm integration counter must reach for an near end Alarm to be declared. If the up count is 6, the down count is 1 and the threshold 1500, an Alarm is integrated in 2.5 sec and removed in 15 seconds." ::= { dsx3AlarmConfigEntry 5 } dsx3FEAlarmUpCount OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "This parameter specifies the increment to the Far End alarm integration counters. The local alarms are RAI and AIS. The Default value is 6 and the integration counter is incremented by this value every 10 ms while the alarm persists. The counter is decremented by the value of dsx3FEAlarmDnCount while there is no alarm (the counter does not decrement below zero). When the integration counter exceeds dsx3FEAlarmThreshold an Alarm of the severity specified for the particular far end alarm is declared. This object is not applicable for CESM-T3/E3. " ::= { dsx3AlarmConfigEntry 6 } dsx3FEAlarmDownCount OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "This parameter specifies the decrement to the Far End alarm integration counters. The local alarms are AIS and RAI. The Default value is 1. The integration counter is decremented by this value every 10 ms (till zero), while no alarm persists. The counter is incremented by the value of dsx3FEAlarmUpCount while there is no alarm. When the integration counter decrements to zero any previously declared Alarm is removed. This object is not applicable for CESM-T3/E3. " ::= { dsx3AlarmConfigEntry 7 } dsx3FEAlarmThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value that the alarm integration counter must reach for an far end Alarm to be declared. If the up count is 6, the down count is 1 and the threshold 1500, an Alarm is integrated in 2.5 sec and removed in 15 seconds. This object is not applicable for CESM-T3/E3. " ::= { dsx3AlarmConfigEntry 8 } dsx3StatisticalAlarmSeverity OBJECT-TYPE SYNTAX INTEGER { minor(1), major(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable is used to setup the severity of any of the Statistical alarms. So when a Statistical Counter exceeds its specified threshold the card will send the alarm with appropriate severity. A major alarm will cause the audible notification and the MAJOR ALARM LED will be turned ON. A minor alarm will just turn on the MINOR ALARM LED." ::= { dsx3AlarmConfigEntry 9 } dsx3LCV15MinThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared." ::= { dsx3AlarmConfigEntry 10 } dsx3LCV24HrThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval" ::= { dsx3AlarmConfigEntry 11 } dsx3LES15MinThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared." ::= { dsx3AlarmConfigEntry 12 } dsx3LES24HrThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval" ::= { dsx3AlarmConfigEntry 13 } dsx3LSES15MinThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared." ::= { dsx3AlarmConfigEntry 14 } dsx3LSES24HrThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval" ::= { dsx3AlarmConfigEntry 15 } dsx3PCV15MinThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. This object is not supported in CESM-T3/E3. This object is not applicable for E3 interface." ::= { dsx3AlarmConfigEntry 16 } dsx3PCV24HrThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval This object is not supported in CESM-T3/E3. This object is not applicable for E3 interface." ::= { dsx3AlarmConfigEntry 17 } dsx3PES15MinThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. This object is not supported in CESM-T3/E3. This object is not applicable for E3 interface." ::= { dsx3AlarmConfigEntry 18 } dsx3PES24HrThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval. This object is not supported in CESM-T3/E3 This object is not applicable for E3 interface." ::= { dsx3AlarmConfigEntry 19 } dsx3PSES15MinThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. This object does not apply to the E3 interface. This object is not supported in CESM-T3/E3." ::= { dsx3AlarmConfigEntry 20 } dsx3PSES24HrThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval. This object is not applicable for E3 interface. This object is not supported in CESM-T3/E3." ::= { dsx3AlarmConfigEntry 21 } dsx3SEFS15MinThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. This object is not supported in CESM-T3/E3" ::= { dsx3AlarmConfigEntry 22 } dsx3SEFS24HrThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval. This object is not supported in CESM-T3/E3" ::= { dsx3AlarmConfigEntry 23 } dsx3AISS15MinThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. This object is not supported in CESM-T3/E3" ::= { dsx3AlarmConfigEntry 24 } dsx3AISS24HrThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval This object is not supported in CESM-T3/E3" ::= { dsx3AlarmConfigEntry 25 } dsx3UAS15MinThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared." ::= { dsx3AlarmConfigEntry 26 } dsx3UAS24HrThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval" ::= { dsx3AlarmConfigEntry 27 } dsx3E3BIP8CV15MinThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "G.832 BIP-8 error monitoring byte. 15 minute threshold value. This has no significance to E3 with G.751 framing which is used in FRSM-VHS This object is not supported in CESM-T3/E3." ::= { dsx3AlarmConfigEntry 28 } dsx3E3BIP8CV24HrThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "G.832 BIP-8 error monitoring byte. 24 hour threshold value. This has no significance to E3 with G.751 framing which is used in FRSM-VHS. This object is not supported in CESM-T3/E3." ::= { dsx3AlarmConfigEntry 29 } dsx3E3BIP8ES15MinThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "G.832 BIP-8 error monitoring byte. 15 minute threshold value. This has no significance to E3 with G.751 framing which is used in FRSM-VHS. This object is not supported in CESM-T3/E3." ::= { dsx3AlarmConfigEntry 30 } dsx3E3BIP8ES24HrThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "G.832 BIP-8 error monitoring byte. 24 hour threshold value. This has no significance to E3 with G.751 framing which is used in FRSM-VHS This object is not supported in CESM-T3/E3 " ::= { dsx3AlarmConfigEntry 31 } dsx3E3BIP8SES15MinThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "G.832 BIP-8 error monitoring byte. 15 minute threshold value. This has no significance to E3 with G.751 framing which is used in FRSM-VHS This object is not supported in CESM-T3/E3 " ::= { dsx3AlarmConfigEntry 32 } dsx3E3BIP8SES24HrThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "G.832 BIP-8 error monitoring byte. 24 hour threshold value. This has no significance to E3 with G.751 framing which is used in FRSM-VHS This object is not supported in CESM-T3/E3 " ::= { dsx3AlarmConfigEntry 33 } dsx3CCV15MinThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. This object is not applicable for E3 interface. This object is not supported in CESM-T3/E3." ::= { dsx3AlarmConfigEntry 34 } dsx3CCV24HrThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval This object is not applicable for E3 interface. This object is not supported in CESM-T3/E3." ::= { dsx3AlarmConfigEntry 35 } dsx3CES15MinThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. This object is not applicable for E3 interface. This object is not supported in CESM-T3/E3." ::= { dsx3AlarmConfigEntry 36 } dsx3CES24HrThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. This object is not applicable for E3 interface. This object is not supported in CESM-T3/E3." ::= { dsx3AlarmConfigEntry 37 } dsx3CSES15MinThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. This object is not applicable for E3 interface. This object is not supported in CESM-T3/E3." ::= { dsx3AlarmConfigEntry 38 } dsx3CSES24HrThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. This object is not applicable for E3 interface. This object is not supported in CESM-T3/E3." ::= { dsx3AlarmConfigEntry 39 } -- -------------------------------------------------------------- -- -- dsx3Alarm group -- This group contains dsx3 Alarm table -- -- -------------------------------------------------------------- dsx3AlarmTable OBJECT-TYPE SYNTAX SEQUENCE OF Dsx3AlarmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The DSX3 interface alarm table. This table contains the performance statistics and Error Events based on 15 minute and/or 24 hour interval. Performance Parameters: LES : Line Errored Seconds PES : P-bit Errored Seconds PSES : P-bit Severely Errored Seconds CES : C-bit Errored Seconds CSES : C-bit Severely Errored Seconds SEFS : Severely Errored Framing Seconds UAS : Unavailable Seconds Error Events: BPV : Bipolar Violation EXZ : Excessive Zeros LCV : Line Coding Violation PCV : P-bit Coding Violation CCV : C-bit Coding Violation." REFERENCE "RFC 2496, Section 2.4.1 and 2.4.2" ::= { dsx3Alarm 1 } dsx3AlarmEntry OBJECT-TYPE SYNTAX Dsx3AlarmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the DSX3 Alarm table. The bucket statistics(15 minute and 24 hour interval statistics) are gathered for each ds3/e3 interface. Any entry is created automatically when ds3 interface is created." INDEX { dsx3LineNum } ::= { dsx3AlarmTable 1 } Dsx3AlarmEntry ::= SEQUENCE { dsx3LineAlarmState Integer32, dsx3LineStatisticalAlarmState Integer32, dsx3LCVCurrent Counter32, dsx3LCV15MinBucket Counter32, dsx3LCV24HrBucket Counter32, dsx3LESCurrent Counter32, dsx3LES15MinBucket Counter32, dsx3LES24HrBucket Counter32, dsx3LSESCurrent Counter32, dsx3LSES15MinBucket Counter32, dsx3LSES24HrBucket Counter32, dsx3PCVCurrent Counter32, dsx3PCV15MinBucket Counter32, dsx3PCV24HrBucket Counter32, dsx3PESCurrent Counter32, dsx3PES15MinBucket Counter32, dsx3PES24HrBucket Counter32, dsx3PSESCurrent Counter32, dsx3PSES15MinBucket Counter32, dsx3PSES24HrBucket Counter32, dsx3SEFSCurrent Counter32, dsx3SEFS15MinBucket Counter32, dsx3SEFS24HrBucket Counter32, dsx3AISSCurrent Counter32, dsx3AISS15MinBucket Counter32, dsx3AISS24HrBucket Counter32, dsx3UASCurrent Counter32, dsx3UAS15MinBucket Counter32, dsx3UAS24HrBucket Counter32, dsx3PercentLcvEFS Integer32, dsx3E3BIP8CVCurrent Counter32, dsx3E3BIP8CV15MinBucket Counter32, dsx3E3BIP8CV24HrBucket Counter32, dsx3E3BIP8ESCurrent Counter32, dsx3E3BIP8ES15MinBucket Counter32, dsx3E3BIP8ES24HrBucket Counter32, dsx3E3BIP8SESCurrent Counter32, dsx3E3BIP8SES15MinBucket Counter32, dsx3E3BIP8SES24HrBucket Counter32, dsx3LineAlarmClrButton INTEGER, dsx3CCVCurrent Counter32, dsx3CCV15MinBucket Counter32, dsx3CCV24HrBucket Counter32, dsx3CESCurrent Counter32, dsx3CES15MinBucket Counter32, dsx3CES24HrBucket Counter32, dsx3CSESCurrent Counter32, dsx3CSES15MinBucket Counter32, dsx3CSES24HrBucket Counter32 } dsx3LineAlarmState OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This variable is a bitmap of the DSX3 Line ALarms on the card. A value of zero indicates no alarms. Itemized below are the individual bits: BitPosition Alarm ----------- ----- 0 Receiving RAI 1 Transmitting RAI 2 Receiving AIS 3 Transmitting AIS 4 Receiving OOF 5 Receiving LOS 6 Near End Local Loopback in effect 7 Near End Remote Loopback in effect 8 Receiving test pattern 9 Receive LCD 10 Receiving C-bit Parity pattern " DEFVAL {0} ::= { dsx3AlarmEntry 1 } dsx3LineStatisticalAlarmState OBJECT-TYPE SYNTAX Integer32(0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This is a bitmap of the DSX3 Line Statistical Alarms on the card. Zero indicates no alarms. Itemized below are the individual alarm bits: BitPosition Alarm ----------- ----- 0 LCV 15 minute threshold exceeded 1 LCV 24 hour threshold exceeded 2 LES 15 minute threshold exceeded 3 LES 24 hour threshold exceeded 4 LSES 15 minute threshold exceeded 5 LSES 24 hour threshold exceeded 6 PCV 15 minute threshold exceeded 7 PCV 24 hour threshold exceeded 8 PES 15 minute threshold exceeded 9 PES 24 hour threshold exceeded 10 PSES 15 minute threshold exceeded 11 PSES 24 hour threshold exceeded 12 SEFS 15 minute threshold exceeded 13 SEFS 24 hour threshold exceeded 14 AISS 15 minute threshold exceeded 15 AISS 24 hour threshold exceeded 16 UAS 15 minute threshold exceeded 17 UAS 24 hour threshold exceeded 18 BIP8CV/G.832 15 minute threshold exceeded 19 BIP8CV/G.832 24 hour threshold exceeded 20 BIP8ES/G.832 15 minute threshold exceeded 21 BIP8ES/G.832 24 hour threshold exceeded 22 BIP8SES/G.832 15 minute threshold exceeded 23 BIP8SES/G.832 24 hour threshold exceeded 24 CCV 15 minute threshold exceeded 25 CCV 24 hour threshold exceeded 26 CES 15 minute threshold exceeded 27 CES 24 hour threshold exceeded 28 CSES 15 minute threshold exceeded 29 CSES 24 hour threshold exceeded Bits 18 to 23 do not have any significance if the framing is G.751(which is used in FRSM_VHS) only bits 0,1,2,3,4,5,16 and 17 are applicable to CESM-T3/E3. " DEFVAL { 0 } ::= { dsx3AlarmEntry 2 } dsx3LCVCurrent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Line Code Violations(LCV) encountered by the interface in current 15 minute period." ::= { dsx3AlarmEntry 3 } dsx3LCV15MinBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Line Code Violations(LCV) encountered by the interface in current last 15 minute period." ::= { dsx3AlarmEntry 4 } dsx3LCV24HrBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Line Code Violations(LCV) encountered by the interface in current last 24 hour period." ::= { dsx3AlarmEntry 5 } dsx3LESCurrent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Line Errored Seconds(LES) encountered by the interface in current 15 minute period." ::= { dsx3AlarmEntry 6 } dsx3LES15MinBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Line Errored Seconds(LES) encountered by the interface in last 15 minute period." ::= { dsx3AlarmEntry 7} dsx3LES24HrBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Line Errored Seconds(LES) encountered by the interface in last 24 hour period." ::= { dsx3AlarmEntry 8 } dsx3LSESCurrent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Line Severely Errored Seconds(LSES) encountered by the interface in current 15 minute period." ::= { dsx3AlarmEntry 9 } dsx3LSES15MinBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Line Severely Errored Seconds(LSES) encountered by the interface in last 15 minute period." ::= { dsx3AlarmEntry 10 } dsx3LSES24HrBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Line Severely Errored Seconds(LSES) encountered by the interface in last 24 hour period." ::= { dsx3AlarmEntry 11 } dsx3PCVCurrent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of P-bit Coding Violations(PCV) encountered by the interface in current 15 minute period. This object is not supported in CESM-T3/E3" ::= { dsx3AlarmEntry 12 } dsx3PCV15MinBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of P-bit Coding Violations(PCV) encountered by the interface in last 15 minute period. This object is not supported in CESM-T3/E3" ::= { dsx3AlarmEntry 13 } dsx3PCV24HrBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of P-bit Coding Violations(PCV) encountered by the interface in last 24 Hour period. This object is not supported in CESM-T3/E3" ::= { dsx3AlarmEntry 14 } dsx3PESCurrent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of P-bit Errored Seconds(PES) encountered by the interface in current 15 minute period. This object is not supported in CESM-T3/E3" ::= { dsx3AlarmEntry 15 } dsx3PES15MinBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of P-bit Errored Seconds(PES) encountered by the interface in last 15 minute period. This object is not supported in CESM-T3/E3" ::= { dsx3AlarmEntry 16 } dsx3PES24HrBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of P-bit Errored Seconds(PES) encountered by the interface in last 24 Hour period. This object is not supported in CESM-T3/E3" ::= { dsx3AlarmEntry 17 } dsx3PSESCurrent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of P-bit Severely Errored Seconds(PSES) encountered by the interface in current 15 minute period. This object is not supported in CESM-T3/E3" ::= { dsx3AlarmEntry 18 } dsx3PSES15MinBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of P-bit Severely Errored Seconds(PSES) encountered by the interface in last 15 minute period. This object is not supported in CESM-T3/E3" ::= { dsx3AlarmEntry 19 } dsx3PSES24HrBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of P-bit Severely Errored Seconds(PSES) encountered by the interface in last 24 Hour period. This object is not supported in CESM-T3/E3" ::= { dsx3AlarmEntry 20 } dsx3SEFSCurrent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Severely Errored Framing Seconds(PSES) encountered by the interface in current 15 minute period. This object is not supported in CESM-T3/E3" ::= { dsx3AlarmEntry 21 } dsx3SEFS15MinBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Severely Errored Framing Seconds(PSES) encountered by the interface in last 15 minute period. This object is not supported in CESM-T3/E3" ::= { dsx3AlarmEntry 22 } dsx3SEFS24HrBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Severely Errored Framing Seconds(PSES) encountered by the interface in last 24 Hour period. This object is not supported in CESM-T3/E3" ::= { dsx3AlarmEntry 23 } dsx3AISSCurrent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of AIS Severely Errored Seconds encountered by the interface in current 15 minute period. This object is not supported in CESM-T3/E3" ::= { dsx3AlarmEntry 24 } dsx3AISS15MinBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of AIS Severely Errored Seconds encountered by the interface in last 15 minute period. This object is not supported in CESM-T3/E3" ::= { dsx3AlarmEntry 25 } dsx3AISS24HrBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of AIS Severely Errored Seconds encountered by the interface in last 24 Hour period. This object is not supported in CESM-T3/E3" ::= { dsx3AlarmEntry 26 } dsx3UASCurrent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Unavailable Seconds(UAS) encountered by the interface in current 15 minute period." ::= { dsx3AlarmEntry 27 } dsx3UAS15MinBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Unavailable Seconds(UAS) encountered by the interface in last 15 minute period." ::= { dsx3AlarmEntry 28 } dsx3UAS24HrBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Unavailable Seconds(UAS) encountered by the interface in last 24 Hour period." ::= { dsx3AlarmEntry 29 } dsx3PercentLcvEFS OBJECT-TYPE SYNTAX Integer32(0..100) MAX-ACCESS read-only STATUS current DESCRIPTION "This object gives the percentage of seconds without any LCV Errors in the total elapsed seconds." ::= { dsx3AlarmEntry 30 } dsx3E3BIP8CVCurrent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of G.832 BIP-8 Coding Violations (CV) encountered by the interface in current 15 minute period. This object is not supported in FRSM-VHS and CESM-T3/E3" ::= { dsx3AlarmEntry 31 } dsx3E3BIP8CV15MinBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of G.832 BIP-8 Coding Violations (CV) encountered by the interface in last 15 minute period. This object is not supported in FRSM-VHS and CESM-T3/E3" ::= { dsx3AlarmEntry 32 } dsx3E3BIP8CV24HrBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of G.832 BIP-8 Coding Violations (CV) encountered by the interface in last 24 Hour period. This object is not supported in FRSM-VHS and CESM-T3/E3" ::= { dsx3AlarmEntry 33 } dsx3E3BIP8ESCurrent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of G.832 BIP-8 Errored Seconds(ES) encountered by the interface in current 15 minute period. This object is not supported in FRSM-VHS and CESM-T3/E3" ::= { dsx3AlarmEntry 34 } dsx3E3BIP8ES15MinBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of G.832 BIP-8 Errored Seconds(ES) encountered by the interface in last 15 minute period. This object is not supported in FRSM-VHS and CESM-T3/E3" ::= { dsx3AlarmEntry 35 } dsx3E3BIP8ES24HrBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of G.832 BIP-8 Errored Seconds(ES) encountered by the interface in last 24 Hour period. This object is not supported in FRSM-VHS and CESM-T3/E3" ::= { dsx3AlarmEntry 36 } dsx3E3BIP8SESCurrent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of G.832 BIP-8 Severely Errored Seconds(SES) encountered by the interface in current 15 minute period. This object is not supported in FRSM-VHS and CESM-T3/E3" ::= { dsx3AlarmEntry 37 } dsx3E3BIP8SES15MinBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of G.832 BIP-8 Severely Errored Seconds(SES) encountered by the interface in last 15 minute period. This object is not supported in FRSM-VHS and CESM-T3/E3" ::= { dsx3AlarmEntry 38 } dsx3E3BIP8SES24HrBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of G.832 BIP-8 Severely Errored Seconds(SES) encountered by the interface in last 24 Hour period. This object is not supported in FRSM-VHS and CESM-T3/E3" ::= { dsx3AlarmEntry 39 } dsx3LineAlarmClrButton OBJECT-TYPE SYNTAX INTEGER { noAction(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to dsx3LineAlarmClear will cause all the alarms statuses and counters to reset." ::= {dsx3AlarmEntry 40 } dsx3CCVCurrent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of C-bit Coding Violations(CCV) encountered by the interface in current 15 minute period. This object is not supported in CESM-T3/E3" ::= { dsx3AlarmEntry 41 } dsx3CCV15MinBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of C-bit Coding Violations(CCV) encountered by the interface in last 15 minute period. This object is not supported in CESM-T3/E3" ::= { dsx3AlarmEntry 42 } dsx3CCV24HrBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of C-bit Coding Violations(CCV) encountered by the interface in last 24 Hour period. This object is not supported in CESM-T3/E3" ::= { dsx3AlarmEntry 43 } dsx3CESCurrent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of C-bit Errored Seconds(CES) encountered by the interface in current 15 minute period. This object is not supported in CESM-T3/E3" ::= { dsx3AlarmEntry 44 } dsx3CES15MinBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of C-bit Errored Seconds(CES) encountered by the interface in last 15 minute period. This object is not supported in CESM-T3/E3" ::= { dsx3AlarmEntry 45 } dsx3CES24HrBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of C-bit Errored Seconds(CES) encountered by the interface in last 24 Hour period. This object is not supported in CESM-T3/E3" ::= { dsx3AlarmEntry 46 } dsx3CSESCurrent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of C-bit Severely Errored Seconds(CSES) encountered by the interface in current 15 minute period. This object is not supported in CESM-T3/E3" ::= { dsx3AlarmEntry 47 } dsx3CSES15MinBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of C-bit Severely Errored Seconds(CSES) encountered by the interface in last 15 minute period. This object is not supported in CESM-T3/E3" ::= { dsx3AlarmEntry 48 } dsx3CSES24HrBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of C-bit Severely Errored Seconds(CSES) encountered by the interface in last 24 Hour period. This object is not supported in CESM-T3/E3" ::= { dsx3AlarmEntry 49 } -- -------------------------------------------------------------- -- -- Group "dsx3Counters" -- -- -------------------------------------------------------------- dsx3CounterTable OBJECT-TYPE SYNTAX SEQUENCE OF Dsx3CounterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is for ds3/e3 statistics. This table maintains the number of times the line encountered LOS, LOF, AIS, RAI, CCV and Framing Errors(FE) from the time it is up. Error statistics are cleared when the line is brought up from the failure state." ::= { dsx3Counter 1 } dsx3CounterEntry OBJECT-TYPE SYNTAX Dsx3CounterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table. Statistics are gathered for each ds3/e3 interface. An entry is created automatically for each ds3/e3 interface that is activated." INDEX { dsx3LineNum } ::= { dsx3CounterTable 1 } Dsx3CounterEntry ::= SEQUENCE { dsx3RcvLOSCount Counter32, dsx3RcvOOFCount Counter32, dsx3RAICount Counter32, dsx3CCVCount Counter32, dsx3FECount Counter32, dsx3AtmHECCount Counter32, dsx3AtmHECSecCount Counter32, dsx3AtmSEHECSecCount Counter32, dsx3CounterClrButton INTEGER, dsx3RcvPERRCounter Counter32, dsx3RcvFEBECounter Counter32, dsx3RcvEXZCounter Counter32, dsx3LCVCount Counter32 } dsx3RcvLOSCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the Loss of Signal was detected with or without integrating to LOS alarm." ::= { dsx3CounterEntry 1 } dsx3RcvOOFCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the Out of Frame was detected with or without integrating to OOF alarm. This object is not supported in CESM-T3/E3" ::= { dsx3CounterEntry 2 } dsx3RAICount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times Yellow Alarms was detected with or without integrating to RAI alarm. This object is not supported in CESM-T3/E3" ::= { dsx3CounterEntry 3 } dsx3CCVCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of C Bit Coding Violations encountered by a DS3/E3 interface. This object is not supported in CESM-T3/E3" ::= { dsx3CounterEntry 4 } dsx3FECount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Framing Pattern Errors encountered by a DS3/E3 interface. This object is not supported in CESM-T3/E3" ::= { dsx3CounterEntry 5 } dsx3AtmHECCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Header Check Sequence(HCS) Errors. This object is not supported in CESM-T3/E3" ::= { dsx3CounterEntry 6 } dsx3AtmHECSecCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of HEC errored seconds. This object is not supported in CESM-T3/E3" ::= { dsx3CounterEntry 7 } dsx3AtmSEHECSecCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Severely HEC error seconds. This object is not supported in CESM-T3/E3" ::= { dsx3CounterEntry 8 } dsx3CounterClrButton OBJECT-TYPE SYNTAX INTEGER { noAction(1), clear (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable is used to clear all the counters." ::= { dsx3CounterEntry 9 } dsx3RcvPERRCounter OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of P-bit parity error. This object is not supported in CESM-T3/E3" ::= { dsx3CounterEntry 10 } dsx3RcvFEBECounter OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Far-end block error. This object is not supported in CESM-T3/E3" ::= { dsx3CounterEntry 11 } dsx3RcvEXZCounter OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of excessive zeros This object is not supported in CESM-T3/E3" ::= { dsx3CounterEntry 12 } dsx3LCVCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Line Coding Violations encountered by a DS3/E3 interface." ::= { dsx3CounterEntry 13 } -- -------------------------------------------------------------- -- -- dsx3PlcpConfig group -- This group contains dsx3Plcp configuration table -- -- -------------------------------------------------------------- dsx3PlcpConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF Dsx3PlcpConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains ATM interface DS3 PLCP configuration parameters." ::= { dsx3PlcpConfig 1 } dsx3PlcpConfigEntry OBJECT-TYPE SYNTAX Dsx3PlcpConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the DSX3 PLCP Configuration table." INDEX { dsx3PlcpNum } ::= { dsx3PlcpConfigTable 1 } Dsx3PlcpConfigEntry ::= SEQUENCE { dsx3PlcpNum Integer32, dsx3PlcpCellFraming INTEGER, dsx3PlcpPayloadScramble INTEGER, dsx3PlcpLoopCommand INTEGER } dsx3PlcpNum OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the dsx3 PLCP interface. The value of this object must be same as the value specified in 'dsx3LineNum' object from cwDsx3ConfigTable." ::= { dsx3PlcpConfigEntry 1 } dsx3PlcpCellFraming OBJECT-TYPE SYNTAX INTEGER { framingByPlcp (1), framingbyAtmHec (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value for this object sets the cell delineation method used by the interface. The cell delineation defines how a receiving device recognizes the start and end of an ATM cell. framingByPlcp (1): The ATM Cells are in predetermined location within each PLCP row, so no additional method is needed to delineate ATM cells. framingByAtmHec (2): The Header Error Control field of the ATM cell header is used to delineate ATM cells. " ::= { dsx3PlcpConfigEntry 2 } dsx3PlcpPayloadScramble OBJECT-TYPE SYNTAX INTEGER { enableScrambling (1), disableScrambling (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The value for this object is used for enabling/disabling PLCP cell scrambling." ::= { dsx3PlcpConfigEntry 3 } dsx3PlcpLoopCommand OBJECT-TYPE SYNTAX INTEGER { noLoop (1), remoteLineLoop (2), localLineLoop (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "specifies the type of loopback on the line. The possible value(s) are : noLoop (1): Not in loopback. remoteLineLoop (2): Remote Line Loopback. localLineLoop (3): Local Line Loopback." ::= { dsx3PlcpConfigEntry 4 } dsx3PlcpNumOfValidEntries OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the maximum number of entries in cwDsx3ConfigTable." ::= { dsx3PlcpConfig 2 } -- -------------------------------------------------------------- -- -- dsx3PlcpAlarmConfig group -- -- -------------------------------------------------------------- dsx3PlcpAlarmConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF Dsx3PlcpAlarmConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the ATM interface PLCP alarm parameters." ::= { dsx3PlcpAlarmConfig 1 } dsx3PlcpAlarmConfigEntry OBJECT-TYPE SYNTAX Dsx3PlcpAlarmConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the DSX3 PLCP Alarm Configuration table. Thresholds may be configured for: Errored Seconds (ES) Coding Violations (CV) Severely Errored Seconds (SES) Unavailable Seconds (UAS), Once these thresholds are exceeded, minor or major alarms are raised. Please refer to RFC2496 for descriptions of these errors." INDEX { dsx3PlcpNum } ::= { dsx3PlcpAlarmConfigTable 1 } Dsx3PlcpAlarmConfigEntry ::= SEQUENCE { dsx3PlcpRedSeverity INTEGER, dsx3PlcpRAISeverity INTEGER, dsx3PlcpLssSeverity INTEGER, dsx3PlcpLssEnable INTEGER, dsx3PlcpLssCodeConnected Integer32, dsx3PlcpLssCodeRxLinkDn Integer32, dsx3PlcpLssCodeRxLinkUp Integer32, dsx3PlcpStatisticalAlarmSeverity INTEGER, dsx3PlcpBip8CV15MinThreshold Integer32, dsx3PlcpBip8CV24HrThreshold Integer32, dsx3PlcpBip8ES15MinThreshold Integer32, dsx3PlcpBip8ES24HrThreshold Integer32, dsx3PlcpBip8SES15MinThreshold Integer32, dsx3PlcpBip8SES24HrThreshold Integer32, dsx3PlcpSEFS15MinThreshold Integer32, dsx3PlcpSEFS24HrThreshold Integer32, dsx3PlcpUAS15MinThreshold Integer32, dsx3PlcpUAS24HrThreshold Integer32 } dsx3PlcpRedSeverity OBJECT-TYPE SYNTAX INTEGER { minor(1), major(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable is used to setup the severity of PLCP RED alarm. So when PLCP_OOF alarm is detected the card will declare the alarm with appropriate severity status. A major alarm will cause the audible notification and the MAJOR ALARM LED will be turned ON. A minor alarm will just turn on the MINOR ALARM LED." ::= { dsx3PlcpAlarmConfigEntry 1 } dsx3PlcpRAISeverity OBJECT-TYPE SYNTAX INTEGER { minor(1), major(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable is used to setup the severity of PLCP RAI alarm. So when PLCP RAI alarm is detected the card will send the alarm with appropriate severity status. A major alarm will cause the audible notification and the MAJOR ALARM LED will be turned ON. A minor alarm will just turn on the MINOR ALARM LED." ::= { dsx3PlcpAlarmConfigEntry 2 } dsx3PlcpLssSeverity OBJECT-TYPE SYNTAX INTEGER { minor(1), major(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable is used to setup the severity of PLCP RAI alarm. So when PLCP LSS alarm is detected the card will send the alarm with appropriate severity status. A major alarm will cause the audible notification and the MAJOR ALARM LED will be turned ON. A minor alarm will just turn on the MINOR ALARM LED." ::= { dsx3PlcpAlarmConfigEntry 3 } dsx3PlcpLssEnable OBJECT-TYPE SYNTAX INTEGER { lssEnable (1), lssDisable (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This objects specifies whether the LSS feature is enabled/disabled." ::= { dsx3PlcpAlarmConfigEntry 4 } dsx3PlcpLssCodeConnected OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "This object derfines the value of the LSS code that is to be interpreted as Link Connected." ::= { dsx3PlcpAlarmConfigEntry 5 } dsx3PlcpLssCodeRxLinkDn OBJECT-TYPE SYNTAX Integer32(0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "This object defines the value of the LSS code that is to be identified as Receive Link Down." ::= { dsx3PlcpAlarmConfigEntry 6 } dsx3PlcpLssCodeRxLinkUp OBJECT-TYPE SYNTAX Integer32(0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "This object defines the value of the LSS code that is to be interpreted as Receive Link Up." ::= { dsx3PlcpAlarmConfigEntry 7 } dsx3PlcpStatisticalAlarmSeverity OBJECT-TYPE SYNTAX INTEGER { minor(1), major(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable sets up the severity of PLCP Statistical alarm. So when PLCP Statistical alarm is detected, the card will send the alarm with appropriate severity. A major alarm will cause the audible notification and the MAJOR ALARM LED will be turned ON. A minor alarm will just turn on the MINOR ALARM LED. " ::= { dsx3PlcpAlarmConfigEntry 8 } dsx3PlcpBip8CV15MinThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared." ::= { dsx3PlcpAlarmConfigEntry 9 } dsx3PlcpBip8CV24HrThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval" ::= { dsx3PlcpAlarmConfigEntry 10 } dsx3PlcpBip8ES15MinThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared." ::= { dsx3PlcpAlarmConfigEntry 11 } dsx3PlcpBip8ES24HrThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval" ::= { dsx3PlcpAlarmConfigEntry 12 } dsx3PlcpBip8SES15MinThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared." ::= { dsx3PlcpAlarmConfigEntry 13 } dsx3PlcpBip8SES24HrThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval" ::= { dsx3PlcpAlarmConfigEntry 14 } dsx3PlcpSEFS15MinThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared." ::= { dsx3PlcpAlarmConfigEntry 15 } dsx3PlcpSEFS24HrThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval" ::= { dsx3PlcpAlarmConfigEntry 16 } dsx3PlcpUAS15MinThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared." ::= { dsx3PlcpAlarmConfigEntry 17 } dsx3PlcpUAS24HrThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval" ::= { dsx3PlcpAlarmConfigEntry 18 } -- -------------------------------------------------------------- -- -- dsx3PlcpAlarm group -- This group contains dsx3 Alarm table -- -- -------------------------------------------------------------- dsx3PlcpAlarmTable OBJECT-TYPE SYNTAX SEQUENCE OF Dsx3PlcpAlarmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains ATM interface DS3 PLCP alarm configuration." ::= { dsx3PlcpAlarm 1 } dsx3PlcpAlarmEntry OBJECT-TYPE SYNTAX Dsx3PlcpAlarmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the ATM DS3 PLCP alarm table. Bucket statistics (15 minute and 24 Hour interval) are gathered for each ds3/e3 interface automatically." INDEX { dsx3PlcpNum } ::= { dsx3PlcpAlarmTable 1 } Dsx3PlcpAlarmEntry ::= SEQUENCE { dsx3PlcpLineAlarmState Integer32, dsx3PlcpLineStatisticalAlarmState Integer32, dsx3PlcpBip8CVCurrent Counter32, dsx3PlcpBip8CV15MinBucket Counter32, dsx3PlcpBip8CV24HrBucket Counter32, dsx3PlcpBip8ESCurrent Counter32, dsx3PlcpBip8ES15MinBucket Counter32, dsx3PlcpBip8ES24HrBucket Counter32, dsx3PlcpBip8SESCurrent Counter32, dsx3PlcpBip8SES15MinBucket Counter32, dsx3PlcpBip8SES24HrBucket Counter32, dsx3PlcpSEFSCurrent Counter32, dsx3PlcpSEFS15MinBucket Counter32, dsx3PlcpSEFS24HrBucket Counter32, dsx3PlcpUASCurrent Counter32, dsx3PlcpUAS15MinBucket Counter32, dsx3PlcpUAS24HrBucket Counter32, dsx3PlcpAlarmClrButton INTEGER } dsx3PlcpLineAlarmState OBJECT-TYPE SYNTAX Integer32 (0..511) MAX-ACCESS read-only STATUS current DESCRIPTION "This variable is a bitmap of the DSX3 Line alarms. A value of zero indicates no alarms. Itemized below are the individual bits: BitPosition Alarm ----------- ----- 0 Receiving RAI 1 Transmitting RAI 2 Receiving OOF 3 Receiving LSS Link Up 4 Transmitting LSS Link Up 5 Receiving LSS Link Down 6 Transmitting LSS Link Down 7 Near End Local Loopback in effect 8 Near End Remote Loopback in effect " ::= { dsx3PlcpAlarmEntry 1 } dsx3PlcpLineStatisticalAlarmState OBJECT-TYPE SYNTAX Integer32(0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This variable is a bitmap of the DSX3 Line Statictical Alarms on the card. A value of zero indicates no alarms. Itemized below are the individual alarm bits: BitPosition Alarm ----------- ----- 0 Bip8CV 15 minute threshold exceeded 1 Bip8CV 24 hour threshold exceeded 2 Bip8ES 15 minute threshold exceeded 3 Bip8ES 24 hour threshold exceeded 4 Bip8SES 15 minute threshold exceeded 5 Bip8SES 24 hour threshold exceeded 6 Plcp SEFS 15 minute threshold exceeded 7 Plcp SEFS 24 hour threshold exceeded 8 Plcp UAS 15 minute threshold exceeded 9 Plcp UAS 24 hour threshold exceeded " ::= { dsx3PlcpAlarmEntry 2 } dsx3PlcpBip8CVCurrent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter counts the number of BIP-8 code violations encountered by the interface." ::= { dsx3PlcpAlarmEntry 3 } dsx3PlcpBip8CV15MinBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of BIP-8 code violations in the last 15 minute period encountered by the interface." ::= { dsx3PlcpAlarmEntry 4 } dsx3PlcpBip8CV24HrBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of BIP-8 code violations in the last 24 hour period encountered by the interface." ::= { dsx3PlcpAlarmEntry 5 } dsx3PlcpBip8ESCurrent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter counts the number of BIP-8 code violations Errored Seconds encountered by the interface." ::= { dsx3PlcpAlarmEntry 6 } dsx3PlcpBip8ES15MinBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter counts the number of BIP-8 code violations Errored Seconds in the last 15 minutes encountered by the interface." ::= { dsx3PlcpAlarmEntry 7 } dsx3PlcpBip8ES24HrBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter counts the number of BIP-8 code violations Errored Seconds in the last 24 hours encountered by the interface." ::= { dsx3PlcpAlarmEntry 8 } dsx3PlcpBip8SESCurrent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter counts the number of Bip8 code violations Severely Errored Seconds encountered by the interface." ::= { dsx3PlcpAlarmEntry 9 } dsx3PlcpBip8SES15MinBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter counts the number of BIP-8 Severely Errored Seconds in the last 15 minutes encountered by the interface." ::= { dsx3PlcpAlarmEntry 10 } dsx3PlcpBip8SES24HrBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter counts the number of BIP-8 Severely Errored Seconds in the last 24 hours encountered by the interface." ::= { dsx3PlcpAlarmEntry 11 } dsx3PlcpSEFSCurrent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter counts the number of Severely Errored Framing Seconds encountered by the interface." ::= { dsx3PlcpAlarmEntry 12 } dsx3PlcpSEFS15MinBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter counts the number of Severely Errored Framing Seconds in the last 15 minutes encountered by the interface." ::= { dsx3PlcpAlarmEntry 13 } dsx3PlcpSEFS24HrBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter counts the number of Severely Errored Framing Seconds in the last 24 hours encountered by the interface." ::= { dsx3PlcpAlarmEntry 14 } dsx3PlcpUASCurrent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter counts the number of Unavailable Seconds encountered by the interface." ::= { dsx3PlcpAlarmEntry 15 } dsx3PlcpUAS15MinBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter counts the number of Unavailable Seconds in the last 15 minutes encountered by the interface." ::= { dsx3PlcpAlarmEntry 16 } dsx3PlcpUAS24HrBucket OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter counts the number of Unavailable Seconds in the last 24 hours encountered by the interface." ::= { dsx3PlcpAlarmEntry 17 } dsx3PlcpAlarmClrButton OBJECT-TYPE SYNTAX INTEGER { dsx3PlcpAlarmNoAction (1), dsx3PlcpAlarmClear (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable is used to clear all the alarms." ::= { dsx3PlcpAlarmEntry 18 } -- -------------------------------------------------------------- -- -- Group "dsx3PlcpCounters" -- -- -------------------------------------------------------------- dsx3PlcpCounterTable OBJECT-TYPE SYNTAX SEQUENCE OF Dsx3PlcpCounterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table for DS3 PLCP counter table." ::= { dsx3PlcpCounter 1 } dsx3PlcpCounterEntry OBJECT-TYPE SYNTAX Dsx3PlcpCounterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the DS3 PLCP counter table." INDEX { dsx3PlcpNum } ::= { dsx3PlcpCounterTable 1 } Dsx3PlcpCounterEntry ::= SEQUENCE { dsx3PlcpRcvBip8Count Counter32, dsx3PlcpRcvOOFCount Counter32, dsx3PlcpRcvRAICount Counter32, dsx3PlcpFECount Counter32, dsx3PlcpFESecCount Counter32, dsx3PlcpSEFESecCount Counter32, dsx3PlcpFEBECount Counter32, dsx3PlcpFEBESecCount Counter32, dsx3PlcpSEFEBESecCount Counter32, dsx3PlcpHECCount Counter32, dsx3PlcpHECSecCount Counter32, dsx3PlcpSEHECSecCount Counter32, dsx3PlcpCounterClrButton INTEGER } dsx3PlcpRcvBip8Count OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of BIP-8 errors encountered by the interface." ::= { dsx3PlcpCounterEntry 1 } dsx3PlcpRcvOOFCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the Out of Frame(OOF) was detected with or without integrating to OOF alarm." ::= { dsx3PlcpCounterEntry 2 } dsx3PlcpRcvRAICount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times Remote Alarm Indication(RAI) was detected with or without integrating to RAI alarm." ::= { dsx3PlcpCounterEntry 3 } dsx3PlcpFECount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Framing Errors detected." ::= { dsx3PlcpCounterEntry 4 } dsx3PlcpFESecCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Framing Error errored seconds." ::= { dsx3PlcpCounterEntry 5 } dsx3PlcpSEFESecCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Severely errored Framing error seconds." ::= { dsx3PlcpCounterEntry 6 } dsx3PlcpFEBECount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Far End Block Errors(FEBE) detected." ::= { dsx3PlcpCounterEntry 7 } dsx3PlcpFEBESecCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of FEBE errored seconds." ::= { dsx3PlcpCounterEntry 8 } dsx3PlcpSEFEBESecCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Severely errored FEBE seconds." ::= { dsx3PlcpCounterEntry 9 } dsx3PlcpHECCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of HCS Errors." ::= { dsx3PlcpCounterEntry 10 } dsx3PlcpHECSecCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of HEC errored seconds." ::= { dsx3PlcpCounterEntry 11 } dsx3PlcpSEHECSecCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Severely HEC error seconds." ::= { dsx3PlcpCounterEntry 12 } dsx3PlcpCounterClrButton OBJECT-TYPE SYNTAX INTEGER { dsx3PlcpCounterNoAction (1), dsx3PlcpCounterClear (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable is used to clear all the counters." ::= { dsx3PlcpCounterEntry 13 } dsx3PlcpCounterValidEntries OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of entries in the dsx3PlcpCounterTable." ::= { dsx3PlcpCounter 2 } -- conformance information cmDsx3MIBConformance OBJECT IDENTIFIER ::= { ciscoMgx82xxDsx3MIB 2 } cmDsx3MIBGroups OBJECT IDENTIFIER ::= { cmDsx3MIBConformance 1 } cmDsx3MIBCompliances OBJECT IDENTIFIER ::= { cmDsx3MIBConformance 2 } -- compliance statements cmDsx3Compliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for objects related to DS3 MIB." MODULE -- this module MANDATORY-GROUPS { cmDsx3GeneralGroup, cmDsx3ConfGroup, cmDsx3BertConfigGroup, cmDsx3StatsGroup, cmDsx3E3AlarmConfGenGroup, cmDsx3AlarmStatsGenGroup, cmDsx3PlcpConfGroup, cmDsx3PlcpStatsGroup, cmDsx3PlcpAlarmConfGroup, cmDsx3PlcpAlarmGroup } GROUP cmDsx3E3ConfGroup DESCRIPTION "This group is mandatory for those cards which support E3 interfaces." GROUP cmDsx3AlarmConfGroup DESCRIPTION "This group is mandatory for those cards which support DS3 interfaces." GROUP cmDsx3E3AlarmConfGroup DESCRIPTION "This group is mandatory for those cards which support E3 interfaces." GROUP cmDsx3AlarmStatsGroup DESCRIPTION "This group is mandatory for those cards which support DS3 interfaces." GROUP cmDsx3E3AlarmStatsGroup DESCRIPTION "This group is mandatory for those cards which support E3 interfaces." ::= { cmDsx3MIBCompliances 1 } cmDsx3GeneralGroup OBJECT-GROUP OBJECTS { dsx3LineNumOfValidEntries, dsx3PlcpNumOfValidEntries, dsx3PlcpCounterValidEntries } STATUS current DESCRIPTION "The collection of objects which are used for providing number of entries in dsx3 and PLCP tables." ::= { cmDsx3MIBGroups 1 } cmDsx3ConfGroup OBJECT-GROUP OBJECTS { dsx3LineNum, cwDsx3LineType, cwDsx3LineCoding, cwDsx3LineLength, dsx3LineOOFCriteria, dsx3LineAIScBitsCheck, dsx3LineLoopbackCommand, dsx3LineXmtFEACCode, dsx3LineEnable, dsx3FarEndLoopbkLineNum, dsx3LineXmtClockSrc, dsx3FarEndLoopbkLineStatus, dsx3LineEqualizer, dsx3NearEndLoopbkLineStatus, dsx3SubRateEnable, dsx3DsuSelect, dsx3LineRate, dsx3LineScrambleEnable } STATUS current DESCRIPTION "The collection of objects which are used for configuring DS3/E3 interfaces." ::= { cmDsx3MIBGroups 2 } cmDsx3E3ConfGroup OBJECT-GROUP OBJECTS { dsx3LineRcvFEACValidation, dsx3TrailTraceOption, dsx3TxTrailTrace, dsx3RxTrailTrace, dsx3TxTimingMarker, dsx3RxTimingMarker, dsx3TxPayloadType, dsx3RxPayloadType, dsx3TxTumf, dsx3RxTumf } STATUS current DESCRIPTION "The collection of objects which are applicable for E3 interfaces only." ::= { cmDsx3MIBGroups 3 } cmDsx3BertConfigGroup OBJECT-GROUP OBJECTS { dsx3LineBERTEnable, dsx3LineBERTPattern, dsx3LineBERTResult, dsx3BERTResultClrButton } STATUS current DESCRIPTION "The collection of objects which are used for BERT on DS3/E3 interfaces." ::= { cmDsx3MIBGroups 4 } cmDsx3StatsGroup OBJECT-GROUP OBJECTS { dsx3RcvLOSCount, dsx3RcvOOFCount, dsx3RAICount, dsx3CCVCount, dsx3FECount, dsx3AtmHECCount, dsx3AtmHECSecCount, dsx3AtmSEHECSecCount, dsx3CounterClrButton, dsx3RcvPERRCounter, dsx3RcvFEBECounter, dsx3RcvEXZCounter, dsx3LCVCount } STATUS current DESCRIPTION "The collection of objects related to DS3/E3 statistics." ::= { cmDsx3MIBGroups 5 } cmDsx3E3AlarmConfGenGroup OBJECT-GROUP OBJECTS { dsx3RedSeverity, dsx3RAISeverity, dsx3NEAlarmUpCount, dsx3NEAlarmDownCount, dsx3NEAlarmThreshold, dsx3FEAlarmUpCount, dsx3FEAlarmDownCount, dsx3FEAlarmThreshold, dsx3StatisticalAlarmSeverity, dsx3LCV15MinThreshold, dsx3LCV24HrThreshold, dsx3LES15MinThreshold, dsx3LES24HrThreshold, dsx3LSES15MinThreshold, dsx3LSES24HrThreshold, dsx3SEFS15MinThreshold, dsx3SEFS24HrThreshold, dsx3UAS15MinThreshold, dsx3UAS24HrThreshold } STATUS current DESCRIPTION "The collection of objects used for alarm configuration of DS3 and E3 interfaces." ::= { cmDsx3MIBGroups 6 } cmDsx3AlarmConfGroup OBJECT-GROUP OBJECTS { dsx3PCV15MinThreshold, dsx3PCV24HrThreshold, dsx3PES15MinThreshold, dsx3PES24HrThreshold, dsx3PSES15MinThreshold, dsx3PSES24HrThreshold, dsx3AISS15MinThreshold, dsx3AISS24HrThreshold, dsx3CCV15MinThreshold, dsx3CCV24HrThreshold, dsx3CES15MinThreshold, dsx3CES24HrThreshold, dsx3CSES15MinThreshold, dsx3CSES24HrThreshold } STATUS current DESCRIPTION "The collection of objects used for alarm configuration of DS3 interfaces." ::= { cmDsx3MIBGroups 7 } cmDsx3E3AlarmConfGroup OBJECT-GROUP OBJECTS { dsx3E3BIP8CV15MinThreshold, dsx3E3BIP8CV24HrThreshold, dsx3E3BIP8ES15MinThreshold, dsx3E3BIP8ES24HrThreshold, dsx3E3BIP8SES15MinThreshold, dsx3E3BIP8SES24HrThreshold } STATUS current DESCRIPTION "The collection of objects used for alarm configuration of E3 interfaces." ::= { cmDsx3MIBGroups 8 } cmDsx3AlarmStatsGenGroup OBJECT-GROUP OBJECTS { dsx3LineAlarmState, dsx3LineStatisticalAlarmState, dsx3LCVCurrent, dsx3LCV15MinBucket, dsx3LCV24HrBucket, dsx3LESCurrent, dsx3LES15MinBucket, dsx3LES24HrBucket, dsx3LSESCurrent, dsx3LSES15MinBucket, dsx3LSES24HrBucket, dsx3SEFSCurrent, dsx3SEFS15MinBucket, dsx3SEFS24HrBucket, dsx3UASCurrent, dsx3UAS15MinBucket, dsx3UAS24HrBucket, dsx3PercentLcvEFS, dsx3LineAlarmClrButton } STATUS current DESCRIPTION "The collection of objects related to performance statistics and error events for ds3 end e3 interfaces." ::= { cmDsx3MIBGroups 9 } cmDsx3AlarmStatsGroup OBJECT-GROUP OBJECTS { dsx3PCVCurrent, dsx3PCV15MinBucket, dsx3PCV24HrBucket, dsx3PESCurrent, dsx3PES15MinBucket, dsx3PES24HrBucket, dsx3PSESCurrent, dsx3PSES15MinBucket, dsx3PSES24HrBucket, dsx3AISSCurrent, dsx3AISS15MinBucket, dsx3AISS24HrBucket, dsx3CCVCurrent, dsx3CCV15MinBucket, dsx3CCV24HrBucket, dsx3CESCurrent, dsx3CES15MinBucket, dsx3CES24HrBucket, dsx3CSESCurrent, dsx3CSES15MinBucket, dsx3CSES24HrBucket } STATUS current DESCRIPTION "The collection of objects related to performance statistics and error events for ds3 interfaces." ::= { cmDsx3MIBGroups 10 } cmDsx3E3AlarmStatsGroup OBJECT-GROUP OBJECTS { dsx3E3BIP8CVCurrent, dsx3E3BIP8CV15MinBucket, dsx3E3BIP8CV24HrBucket, dsx3E3BIP8ESCurrent, dsx3E3BIP8ES15MinBucket, dsx3E3BIP8ES24HrBucket, dsx3E3BIP8SESCurrent, dsx3E3BIP8SES15MinBucket, dsx3E3BIP8SES24HrBucket } STATUS current DESCRIPTION "The collection of objects related to performance statistics and error events for e3 interfaces." ::= { cmDsx3MIBGroups 11 } cmDsx3PlcpConfGroup OBJECT-GROUP OBJECTS { dsx3PlcpNum, dsx3PlcpCellFraming, dsx3PlcpPayloadScramble, dsx3PlcpLoopCommand } STATUS current DESCRIPTION "The collection of objects related to PLCP Configuration on DS3 interfaces." ::= { cmDsx3MIBGroups 12 } cmDsx3PlcpStatsGroup OBJECT-GROUP OBJECTS { dsx3PlcpRcvBip8Count, dsx3PlcpRcvOOFCount, dsx3PlcpRcvRAICount, dsx3PlcpFECount, dsx3PlcpFESecCount, dsx3PlcpSEFESecCount, dsx3PlcpFEBECount, dsx3PlcpFEBESecCount, dsx3PlcpSEFEBESecCount, dsx3PlcpHECCount, dsx3PlcpHECSecCount, dsx3PlcpSEHECSecCount, dsx3PlcpCounterClrButton } STATUS current DESCRIPTION "The collection of objects related to PLCP statistics on DS3 interfaces." ::= { cmDsx3MIBGroups 13 } cmDsx3PlcpAlarmConfGroup OBJECT-GROUP OBJECTS { dsx3PlcpRedSeverity, dsx3PlcpRAISeverity, dsx3PlcpLssSeverity, dsx3PlcpLssEnable, dsx3PlcpLssCodeConnected, dsx3PlcpLssCodeRxLinkDn, dsx3PlcpLssCodeRxLinkUp, dsx3PlcpStatisticalAlarmSeverity, dsx3PlcpBip8CV15MinThreshold, dsx3PlcpBip8CV24HrThreshold, dsx3PlcpBip8ES15MinThreshold, dsx3PlcpBip8ES24HrThreshold, dsx3PlcpBip8SES15MinThreshold, dsx3PlcpBip8SES24HrThreshold, dsx3PlcpSEFS15MinThreshold, dsx3PlcpSEFS24HrThreshold, dsx3PlcpUAS15MinThreshold, dsx3PlcpUAS24HrThreshold } STATUS current DESCRIPTION "The collection of objects used for PLCP Alarm configuration on DS3 interfaces." ::= { cmDsx3MIBGroups 14 } cmDsx3PlcpAlarmGroup OBJECT-GROUP OBJECTS { dsx3PlcpLineAlarmState, dsx3PlcpLineStatisticalAlarmState, dsx3PlcpBip8CVCurrent, dsx3PlcpBip8CV15MinBucket, dsx3PlcpBip8CV24HrBucket, dsx3PlcpBip8ESCurrent, dsx3PlcpBip8ES15MinBucket, dsx3PlcpBip8ES24HrBucket, dsx3PlcpBip8SESCurrent, dsx3PlcpBip8SES15MinBucket, dsx3PlcpBip8SES24HrBucket, dsx3PlcpSEFSCurrent, dsx3PlcpSEFS15MinBucket, dsx3PlcpSEFS24HrBucket, dsx3PlcpUASCurrent, dsx3PlcpUAS15MinBucket, dsx3PlcpUAS24HrBucket, dsx3PlcpAlarmClrButton } STATUS current DESCRIPTION "The collection of objects used for PLCP Alarm configuration on DS3 interfaces." ::= { cmDsx3MIBGroups 15 } END