-- ***************************************************************** -- Cisco L2 Tunnel Config MIB -- -- April, 2002 Binh Le -- September, 2003 Seth Wang -- -- Copyright (c) 2002-2007 by Cisco Systems, Inc. -- -- All rights reserved. -- **************************************************************** CISCO-L2-TUNNEL-CONFIG-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Unsigned32, Counter32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF TruthValue FROM SNMPv2-TC ifIndex FROM IF-MIB QosLayer2Cos FROM CISCO-QOS-PIB-MIB ciscoMgmt FROM CISCO-SMI; ciscoL2TunnelConfigMIB MODULE-IDENTITY LAST-UPDATED "200702150000Z" ORGANIZATION "Cisco Systems Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS Email: cs-lan-switch-snmp@cisco.com" DESCRIPTION "This MIB module is for layer 2 tunneling related configurations on a device. Tunneling allows separate local networks to be considered as a single VLAN. These separate networks are connected via an ISP, which will tunnel the packets from one network to another, making it appear as if the two networks are actually just one." REVISION "200702150000Z" DESCRIPTION "Modify the descriptions of cltcTunneledProtocolType and cltcTunnelShutdownThreshold. Add 'lldp(4)' to cltcTunneledProtocolType, 'lldp(6)' to cltcTunnelThresholdProtocolIndex and 'lldp(6)' to cltcTunneledProtocolIndex. Add new groups cltcTunnelTotalDropGroup, cltcTunnelSysDropNotifEnableGroup, cltcTunnelSysDropGroup, cltcTunnelSysDropNotifGroup." REVISION "200607250000Z" DESCRIPTION "Modify the descriptions of cltcTunneledProtocolType and cltcTunnelShutdownThreshold." REVISION "200506270000Z" DESCRIPTION "Add 'eoam(3)' to cltcTunneledProtocolType, 'eoam(5)' to cltcTunnelThresholdProtocolIndex and 'eoam(5)' to cltcTunneledProtocolIndex." REVISION "200406090000Z" DESCRIPTION "Change the description for cltcTunnelThresholdProtocolIndex. Add the new groups cltcTunnelThresholdNotifsGroup and cltcNotifsEnableGroup." REVISION "200309030000Z" DESCRIPTION "Add a new object cltcTunnelDropStats. Remove the restriction for enabling cltcDot1qTunnelMode from the description." REVISION "200205311000Z" DESCRIPTION "Add SNMP support for 802.1q All Tagged (dot1q-all-tagged) Per Port feature. Dot1q-all-tagged feature is an enhancement to tag the packets on the native vlan to avoid any confusion in the ISP network, and to avoid vlan hopping when the native vlan for the trunk is as same as the vlan assigned for a customer. Before this enhancement, this feature can be enabled/disabled globally through the vlanTrunkPortsDot1qTag object in CISCO-VTP-MIB. With this enhacement, vlanTrunkPortsDot1qTag object in CISCO-VTP-MIB is deprecated and replaced by the dot1qAllTaggedEnabled object in this MIB. Additionally, dot1q-all-tag will be able to configure per port basis." REVISION "200202140000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 246 } cltcMIBObjects OBJECT IDENTIFIER ::= { ciscoL2TunnelConfigMIB 1 } cltcGlobal OBJECT IDENTIFIER ::= { cltcMIBObjects 1 } cltcDot1qTunnel OBJECT IDENTIFIER ::= { cltcMIBObjects 2 } cltcTunneledProtocol OBJECT IDENTIFIER ::= { cltcMIBObjects 3 } cltcTunnelThreshold OBJECT IDENTIFIER ::= { cltcMIBObjects 4 } cltcTunnelStatistics OBJECT IDENTIFIER ::= { cltcMIBObjects 5 } -- MIB objects for 802.1q All Tagged Per Port(dot1q-all-tagged) feature. cltcDot1qAllTagged OBJECT IDENTIFIER ::= { cltcMIBObjects 6 } -- cltcTunnelCos cltcTunnelCos OBJECT-TYPE SYNTAX QosLayer2Cos MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the user priority of the tunneled PDUs and applies to all ingress tunneling interfaces." ::= { cltcGlobal 1 } cltcNotificationEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether the system will generate the cltcTunnelDropThresholdExceeded and cltcTunnelShutdownThresholdExceeded notifications." ::= { cltcGlobal 2 } cltcTunnelSysDropThreshold OBJECT-TYPE SYNTAX Unsigned32 UNITS "PDUs/sec" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the drop threshold at the system level. A value of zero indicates that system level rate limiting is disabled." ::= { cltcGlobal 3 } cltcTunnelSysDropNotifEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether the system will generate the cltcTunnelSysDropThresholdExceeded notification." ::= { cltcGlobal 4 } -- cltcDot1qTunnelTable cltcDot1qTunnelTable OBJECT-TYPE SYNTAX SEQUENCE OF CltcDot1qTunnelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information about the dot1q tunnel interfaces. Only dot1q tunneling capable interfaces are shown. 1Q-in-1Q will allow service providers to separate the traffic of various customers within their infrastructure while the customers appear to be on the same VLANs." ::= { cltcDot1qTunnel 1 } cltcDot1qTunnelEntry OBJECT-TYPE SYNTAX CltcDot1qTunnelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about the dot1q tunnel. Only dot1q tunneling capable interfaces are shown." INDEX { ifIndex } ::= { cltcDot1qTunnelTable 1 } CltcDot1qTunnelEntry ::= SEQUENCE { cltcDot1qTunnelMode INTEGER } cltcDot1qTunnelMode OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates the dot1q tunnel mode of the interface. Setting the interface to dot1q tunnel 'disabled' mode causes the dot1q tunnel feature to be disabled on this interface. Setting the interface to dot1q tunnel 'enabled' mode causes the dot1q tunnel feature to be enabled on this interface." DEFVAL { disabled } ::= { cltcDot1qTunnelEntry 1 } -- cltcTunneledProtocolTable cltcTunneledProtocolTable OBJECT-TYPE SYNTAX SEQUENCE OF CltcTunneledProtocolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information about the protocols being tunneled. Only tunneled protocol filtering capable interfaces are shown." ::= { cltcTunneledProtocol 1 } cltcTunneledProtocolEntry OBJECT-TYPE SYNTAX CltcTunneledProtocolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about the protocols being tunneled. Only tunneled protocol filtering capable interfaces are shown." INDEX { ifIndex } ::= { cltcTunneledProtocolTable 1 } CltcTunneledProtocolEntry ::= SEQUENCE { cltcTunneledProtocolType BITS } cltcTunneledProtocolType OBJECT-TYPE SYNTAX BITS { cdp(0), vtp(1), stp(2), eoam(3), lldp(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates tunneled protocol of the interface. If a BIT is set, then the value of the corresponding protocol is tunneled. Specifically, if the 'cdp(0)' BIT is set, then the Cisco Discovery Protocol PDU is tunneled; if the 'vtp(1)' BIT is set, then the VLAN Trunking Protocol PDU is tunneled; if the 'stp(2)' BIT is set, then the Spanning Tree Protocol PDU is tunneled; if the 'eoam(3)' BIT is set, then the ethernet Operation, Administration and Maintenance PDU is tunneled; if the 'lldp(4)' BIT is set, then the Link Layer Discovery Protocol is tunneled. If the bit for a given protocol is set for an interface, then the statistics for that interface and protocol will start to be monitored." ::= { cltcTunneledProtocolEntry 1 } -- cltcTunnelThresholdTable cltcTunnelThresholdTable OBJECT-TYPE SYNTAX SEQUENCE OF CltcTunnelThresholdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information about the thresholds for protocol tunneling. Only tunneled protocol filtering capable interfaces are shown. The objects will be on a per interface, per protocol basis." ::= { cltcTunnelThreshold 1 } cltcTunnelThresholdEntry OBJECT-TYPE SYNTAX CltcTunnelThresholdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about the thresholds for protocol tunneling. Only tunneled protocol filtering capable interfaces are shown. The entries will be on a per interface, per protocol basis" INDEX { ifIndex, cltcTunnelThresholdProtocolIndex } ::= { cltcTunnelThresholdTable 1 } CltcTunnelThresholdEntry ::= SEQUENCE { cltcTunnelThresholdProtocolIndex INTEGER, cltcTunnelDropThreshold Unsigned32, cltcTunnelShutdownThreshold Unsigned32 } cltcTunnelThresholdProtocolIndex OBJECT-TYPE SYNTAX INTEGER { all(1), cdp(2), vtp(3), stp(4), eoam(5), lldp(6) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "A tunneled protocol of an interface. - all(1) is supported for devices which allow the setting of thresholds on a per interface basis. This threshold is a combined threshold for the interface which includes all supported protocols. - cdp(2), vtp(3), stp(4), eoam(5) and lldp(6) are supported for devices which allow the setting of thresholds on a per interface, per protocol basis." ::= { cltcTunnelThresholdEntry 1 } cltcTunnelDropThreshold OBJECT-TYPE SYNTAX Unsigned32 UNITS "PDUs/sec" MAX-ACCESS read-write STATUS current DESCRIPTION "The drop threshold on an interface for a given protocol. After reaching this drop threshold, the interface will start dropping PDUs for the given protocol. This value cannot be greater than the value of cltcTunnelShutdownThreshold. A value of 0 indicates that no limit is set." DEFVAL { 0 } ::= { cltcTunnelThresholdEntry 2 } cltcTunnelShutdownThreshold OBJECT-TYPE SYNTAX Unsigned32 UNITS "PDUs/sec" MAX-ACCESS read-write STATUS current DESCRIPTION "The shutdown threshold on an interface for a given protocol. After reaching the shutdown threshold, the interface will shutdown for the given protocol. This value cannot be less than the value of cltcTunnelDropThreshold. A value of 0 indicates that no limit is set." DEFVAL { 0 } ::= { cltcTunnelThresholdEntry 3 } -- cltcTunnelStatisticsTable cltcTunnelStatisticsTable OBJECT-TYPE SYNTAX SEQUENCE OF CltcTunnelStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains protocol tunneling statistics on the interface." ::= { cltcTunnelStatistics 1 } cltcTunnelStatisticsEntry OBJECT-TYPE SYNTAX CltcTunnelStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Protocol tunneling statistics on the interface." INDEX { ifIndex, cltcTunneledProtocolIndex } ::= { cltcTunnelStatisticsTable 1 } CltcTunnelStatisticsEntry ::= SEQUENCE { cltcTunneledProtocolIndex INTEGER , cltcTunnelEncapStats Counter32, cltcTunnelDeEncapStats Counter32, cltcTunnelDropStats Counter32 } cltcTunneledProtocolIndex OBJECT-TYPE SYNTAX INTEGER { cdp(2), vtp(3), stp(4), eoam(5), lldp(6) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "A tunneled protocol of an interface." ::= { cltcTunnelStatisticsEntry 1 } cltcTunnelEncapStats OBJECT-TYPE SYNTAX Counter32 UNITS "encapsulated PDUs" MAX-ACCESS read-only STATUS current DESCRIPTION "The tunneled PDU encapsulation statistics of an interface. These statistics cover the number of tunneled ingress PDUs." ::= { cltcTunnelStatisticsEntry 2 } cltcTunnelDeEncapStats OBJECT-TYPE SYNTAX Counter32 UNITS "de-encapsulated PDUs" MAX-ACCESS read-only STATUS current DESCRIPTION "The tunneled PDU de-encapsulation statistics of an interface. These statistics cover the number of tunneled egress PDUs." ::= { cltcTunnelStatisticsEntry 3 } cltcTunnelDropStats OBJECT-TYPE SYNTAX Counter32 UNITS "PDUs" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of PDUs dropped on an interface for a given protocol. The PDUs will be dropped when the cltcTunnelDropThreshold is reached." ::= { cltcTunnelStatisticsEntry 4 } -- cltcTunnelDropStatTable cltcTunnelDropStatTable OBJECT-TYPE SYNTAX SEQUENCE OF CltcTunnelDropStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains protocol tunneling drop statistics." ::= { cltcTunnelStatistics 2 } cltcTunnelDropStatEntry OBJECT-TYPE SYNTAX CltcTunnelDropStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Drop statistics for a tunneled protocol." INDEX { cltcTunneledProtocolIndex } ::= { cltcTunnelDropStatTable 1 } CltcTunnelDropStatEntry ::= SEQUENCE { cltcTunnelTotalDropStats Counter32 } cltcTunnelTotalDropStats OBJECT-TYPE SYNTAX Counter32 UNITS "encapsulated PDUs" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of tunneled ingress PDUs that have been dropped." ::= { cltcTunnelDropStatEntry 1 } -- dot1qAllTaggedEnabled cltcDot1qAllTaggedEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object controls if dot1q-all-tagged feature is enabled in the managed system." ::= { cltcDot1qAllTagged 1 } -- cltcDot1qAllTaggedIfTable cltcDot1qAllTaggedIfTable OBJECT-TYPE SYNTAX SEQUENCE OF CltcDot1qAllTaggedIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information about the dot1q-all-tagged feature's configuration of capable interfaces in the system." ::= { cltcDot1qAllTagged 2 } cltcDot1qAllTaggedIfEntry OBJECT-TYPE SYNTAX CltcDot1qAllTaggedIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Configuration of dot1q-all-tagged feature on interfaces. Each entry is created for a dot1q-all-tagged capable interface in the system." INDEX { ifIndex } ::= { cltcDot1qAllTaggedIfTable 1 } CltcDot1qAllTaggedIfEntry ::= SEQUENCE { cltcDot1qAllTaggedIfEnabled TruthValue } cltcDot1qAllTaggedIfEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether dot1q-all-tagged feature has been enabled on a specific interface." ::= { cltcDot1qAllTaggedIfEntry 1 } -- Notifications cltcMIBNotifications OBJECT IDENTIFIER ::= { ciscoL2TunnelConfigMIB 2 } cltcMIBNotificationsPrefix OBJECT IDENTIFIER ::= { cltcMIBNotifications 0 } cltcTunnelDropThresholdExceeded NOTIFICATION-TYPE OBJECTS { cltcTunnelDropThreshold } STATUS current DESCRIPTION "This notification is generated when the cltcTunnelDropThreshold has been exceeded." ::= { cltcMIBNotificationsPrefix 1 } cltcTunnelShutdownThresholdExceeded NOTIFICATION-TYPE OBJECTS { cltcTunnelShutdownThreshold } STATUS current DESCRIPTION "This notification is generated when the cltcTunnelShutdownThreshold has been exceeded." ::= { cltcMIBNotificationsPrefix 2 } cltcTunnelSysDropThresholdExceeded NOTIFICATION-TYPE OBJECTS { cltcTunnelSysDropThreshold } STATUS current DESCRIPTION "This notification is generated when the cltcTunnelSysDropThreshold has been exceeded." ::= { cltcMIBNotificationsPrefix 3 } -- Conformance cltcMIBConformance OBJECT IDENTIFIER ::= { ciscoL2TunnelConfigMIB 3 } cltcMIBCompliances OBJECT IDENTIFIER ::= { cltcMIBConformance 1 } cltcMIBGroups OBJECT IDENTIFIER ::= { cltcMIBConformance 2 } -- Compliance cltcMIBCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the CISCO-L2-TUNNEL-CONFIG-MIB." MODULE -- this module GROUP cltcDot1qTunnelGroup DESCRIPTION "A collection of objects for configuring dot1q tunnneling. This group is mandatory only in devices which support dot1q tunneling." GROUP cltcTunneledProtocolGroup DESCRIPTION "A collection of objects for configuring tunneled protocols. This group is mandatory only in devices which support dot1q tunneling." GROUP cltcTunnelThresholdGroup DESCRIPTION "A collection of objects for configuring the thresholds for protocol tunneling. This group is mandatory only in devices which support protocol tunneling." GROUP cltcTunnelStatisticsGroup DESCRIPTION "A collection of objects which give the statistics regarding the tunneling interfaces. This group is mandatory only in devices which support tunneling statistics." ::= { cltcMIBCompliances 1 } cltcMIBCompliance2 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the CISCO-L2-TUNNEL-CONFIG-MIB." MODULE -- this module GROUP cltcDot1qTunnelGroup DESCRIPTION "A collection of objects for configuring dot1q tunnneling. This group is mandatory only in devices which support dot1q tunneling." GROUP cltcTunneledProtocolGroup DESCRIPTION "A collection of objects for configuring tunneled protocols. This group is mandatory only in devices which support dot1q tunneling." GROUP cltcTunnelThresholdGroup DESCRIPTION "A collection of objects for configuring the thresholds for protocol tunneling. This group is mandatory only in devices which support protocol tunneling." GROUP cltcTunnelStatisticsGroup DESCRIPTION "A collection of objects which give the statistics regarding the tunneling interfaces. This group is mandatory only in devices which support tunneling statistics." GROUP cltcDot1qAllTaggedGroup DESCRIPTION "This group is mandatory only in devices which support dot1q-all-tagged feature." OBJECT cltcDot1qAllTaggedEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cltcDot1qAllTaggedIfEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { cltcMIBCompliances 2 } cltcMIBCompliance3 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the CISCO-L2-TUNNEL-CONFIG-MIB." MODULE -- this module GROUP cltcDot1qTunnelGroup DESCRIPTION "A collection of objects for configuring dot1q tunnneling. This group is mandatory only in devices which support dot1q tunneling." GROUP cltcTunneledProtocolGroup DESCRIPTION "A collection of objects for configuring tunneled protocols. This group is mandatory only in devices which support dot1q tunneling." GROUP cltcTunnelThresholdGroup DESCRIPTION "A collection of objects for configuring the thresholds for protocol tunneling. This group is mandatory only in devices which support protocol tunneling." GROUP cltcTunnelStatisticsGroup DESCRIPTION "A collection of objects which give the statistics regarding the tunneling interfaces. This group is mandatory only in devices which support tunneling statistics." GROUP cltcDot1qAllTaggedGroup DESCRIPTION "This group is mandatory only in devices which support dot1q-all-tagged feature." GROUP cltcTunnelDropStatisticsGroup DESCRIPTION "A collection of objects which give the statistics regarding dropped PDUs on the tunneling interfaces. This group is mandatory only in devices which support tunneling drop statistics." OBJECT cltcDot1qAllTaggedEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cltcDot1qAllTaggedIfEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { cltcMIBCompliances 3 } cltcMIBCompliance4 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the CISCO-L2-TUNNEL-CONFIG-MIB." MODULE -- this module GROUP cltcDot1qTunnelGroup DESCRIPTION "A collection of objects for configuring dot1q tunnneling. This group is mandatory only in devices which support dot1q tunneling." GROUP cltcTunneledProtocolGroup DESCRIPTION "A collection of objects for configuring tunneled protocols. This group is mandatory only in devices which support dot1q tunneling." GROUP cltcTunnelThresholdGroup DESCRIPTION "A collection of objects for configuring the thresholds for protocol tunneling. This group is mandatory only in devices which support protocol tunneling." GROUP cltcTunnelStatisticsGroup DESCRIPTION "A collection of objects which give the statistics regarding the tunneling interfaces. This group is mandatory only in devices which support tunneling statistics." GROUP cltcDot1qAllTaggedGroup DESCRIPTION "This group is mandatory only in devices which support dot1q-all-tagged feature." GROUP cltcTunnelDropStatisticsGroup DESCRIPTION "A collection of objects which give the statistics regarding dropped PDUs on the tunneling interfaces. This group is mandatory only in devices which support tunneling drop statistics." GROUP cltcNotifsEnableGroup DESCRIPTION "A collections of objects used to enable notifications. This group is mandatory only in devices which support the protocol tunneling notification feature." GROUP cltcTunnelThresholdNotifsGroup DESCRIPTION "A collection of notifications used for the tunnel thresholds. This group is mandatory only in devices which support the protocol tunneling notification feature." OBJECT cltcDot1qAllTaggedEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cltcDot1qAllTaggedIfEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { cltcMIBCompliances 4 } cltcMIBCompliance5 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for the CISCO-L2-TUNNEL-CONFIG-MIB." MODULE -- this module GROUP cltcDot1qTunnelGroup DESCRIPTION "This group is mandatory only in devices which support dot1q tunneling." GROUP cltcTunneledProtocolGroup DESCRIPTION "This group is mandatory only in devices which support dot1q tunneling." GROUP cltcTunnelThresholdGroup DESCRIPTION "This group is mandatory only in devices which support protocol tunneling threshold feature." GROUP cltcTunnelStatisticsGroup DESCRIPTION "This group is mandatory only in devices which support per interface tunneling statistics." GROUP cltcDot1qAllTaggedGroup DESCRIPTION "This group is mandatory only in devices which support dot1q-all-tagged feature." GROUP cltcTunnelDropStatisticsGroup DESCRIPTION "This group is mandatory only in devices which support per interface tunneling drop statistics." GROUP cltcTunnelTotalDropGroup DESCRIPTION "This group is mandatory only in devices which support per device tunneling drop statistics." GROUP cltcNotifsEnableGroup DESCRIPTION "This group is mandatory only in devices which support the protocol tunneling notification feature." GROUP cltcTunnelThresholdNotifsGroup DESCRIPTION "This group is mandatory only in devices which support the protocol tunneling notification feature." GROUP cltcTunnelSysDropNotifEnableGroup DESCRIPTION "This group is mandatory only in devices which support the notification for the system drop threshold." GROUP cltcTunnelSysDropGroup DESCRIPTION "This group is mandatory only in devices which support the system drop threshold." GROUP cltcTunnelSysDropNotifGroup DESCRIPTION "This group is mandatory only in devices which support the notification for the system drop threshold." OBJECT cltcDot1qAllTaggedEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cltcDot1qAllTaggedIfEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { cltcMIBCompliances 5 } -- Units of Conformance cltcDot1qTunnelGroup OBJECT-GROUP OBJECTS { cltcDot1qTunnelMode } STATUS current DESCRIPTION "A collection of objects for configuring dot1q tunnneling." ::= { cltcMIBGroups 1 } cltcTunneledProtocolGroup OBJECT-GROUP OBJECTS { cltcTunneledProtocolType, cltcTunnelCos } STATUS current DESCRIPTION "A collection of objects for configuring tunneled protocols." ::= { cltcMIBGroups 2 } cltcTunnelThresholdGroup OBJECT-GROUP OBJECTS { cltcTunnelDropThreshold, cltcTunnelShutdownThreshold } STATUS current DESCRIPTION "A collection of objects for configuring the thresholds for protocol tunneling." ::= { cltcMIBGroups 3 } cltcTunnelStatisticsGroup OBJECT-GROUP OBJECTS { cltcTunnelEncapStats, cltcTunnelDeEncapStats } STATUS current DESCRIPTION "A collection of objects which give the statistics regarding the tunneling interfaces." ::= { cltcMIBGroups 4 } cltcDot1qAllTaggedGroup OBJECT-GROUP OBJECTS { cltcDot1qAllTaggedEnabled, cltcDot1qAllTaggedIfEnabled } STATUS current DESCRIPTION "A collection of objects for configuring the dot1q-all-tagged feature in the system." ::= { cltcMIBGroups 5 } cltcTunnelDropStatisticsGroup OBJECT-GROUP OBJECTS { cltcTunnelDropStats } STATUS current DESCRIPTION "A collection of objects which give the statistics regarding dropped PDUs on the tunneling interfaces." ::= { cltcMIBGroups 6 } cltcNotifsEnableGroup OBJECT-GROUP OBJECTS { cltcNotificationEnable } STATUS current DESCRIPTION "A collections of objects used to enable notifications." ::= { cltcMIBGroups 7 } cltcTunnelThresholdNotifsGroup NOTIFICATION-GROUP NOTIFICATIONS { cltcTunnelDropThresholdExceeded, cltcTunnelShutdownThresholdExceeded } STATUS current DESCRIPTION "A collection of notifications used for the tunnel thresholds." ::= { cltcMIBGroups 8 } cltcTunnelTotalDropGroup OBJECT-GROUP OBJECTS { cltcTunnelTotalDropStats } STATUS current DESCRIPTION "A collection of objects which give the statistics regarding total number of dropped PDUs per protocol type." ::= { cltcMIBGroups 9 } cltcTunnelSysDropNotifEnableGroup OBJECT-GROUP OBJECTS { cltcTunnelSysDropNotifEnable } STATUS current DESCRIPTION "A collection of object to enable cltcTunnelSysDropThresholdExceeded notification." ::= { cltcMIBGroups 10 } cltcTunnelSysDropGroup OBJECT-GROUP OBJECTS { cltcTunnelSysDropThreshold } STATUS current DESCRIPTION "A collection of object for configuring the system level rate limiting." ::= { cltcMIBGroups 11 } cltcTunnelSysDropNotifGroup NOTIFICATION-GROUP NOTIFICATIONS { cltcTunnelSysDropThresholdExceeded } STATUS current DESCRIPTION "A collection of notification used for the system level rate limiting has been exceeded." ::= { cltcMIBGroups 12 } END