-- ***************************************************************** -- CISCO-L2-DEV-MONITORING-MIB.my: CISCO L2 DEVICE MONITORING MIB -- file -- -- August 2001, Francis Pang -- -- Copyright (c) 2001-2003 by Cisco Systems, Inc. -- All rights reserved. -- ***************************************************************** -- CISCO-L2-DEV-MONITORING-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-TYPE, Unsigned32 FROM SNMPv2-SMI MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP FROM SNMPv2-CONF MacAddress, TruthValue, RowStatus FROM SNMPv2-TC InterfaceIndex FROM IF-MIB ciscoMgmt FROM CISCO-SMI; ciscoL2DevMonMIB MODULE-IDENTITY LAST-UPDATED "200307220000Z" ORGANIZATION "Cisco System Inc." CONTACT-INFO " Cisco Systems Customer Service Postal: 170 West Tasman Drive, San Jose CA 95134-1706. USA Tel: +1 800 553-NETS E-mail: cs-snmp@cisco.com" DESCRIPTION "This MIB module is for monitoring of active layer 2 devices by hot standby layer 2 devices and the configuration of hot standby switch-over parameters." REVISION "200307220000Z" DESCRIPTION "Added cl2DevMonActiveRadioMacType to identify to the device radio MAC protocol type and cl2DevMonActiveLocalRadioIndex to identify the local radio used for monitoring." REVISION "200109270000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 271 } ciscoL2DevMonMIBObjects OBJECT IDENTIFIER ::= { ciscoL2DevMonMIB 1 } cl2DevMonConfig OBJECT IDENTIFIER ::= { ciscoL2DevMonMIBObjects 1} -- ***************************************************************** -- Attributes for Hot Standby Monitoring unit -- ***************************************************************** cl2DevMonInStandbyMode OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "If the value of this variable is TRUE, this device is in monitoring or standby mode and it will poll for the health of the devices on the cl2DevMonActiveTable. If the value of cl2DevMonInStandbyMode is FALSE, it only can be set back to TRUE using command line interface or SNMP request. The value can be set to FALSE only by the device itself because force switch over from standby mode to active mode is not allowed." DEFVAL { false } ::= { cl2DevMonConfig 1 } cl2DevMonNotifEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether cl2DevMonSwitchover notifications will or will not be sent by the device when it changes its cl2DevMonInStandbyMode to FALSE and becomes an active unit." DEFVAL { false } ::= { cl2DevMonConfig 2 } cl2DevMonActiveTable OBJECT-TYPE SYNTAX SEQUENCE OF Cl2DevMonActiveEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table for active devices on the network being monitored by the hot standby monitoring unit. This table is on the hot standby monitoring unit. All entries on this table will only be added, deleted, modified using command user interface or SNMP request." ::= { cl2DevMonConfig 3 } cl2DevMonActiveEntry OBJECT-TYPE SYNTAX Cl2DevMonActiveEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the cl2DevMonActiveTable table." INDEX { cl2DevMonActiveMacAddress } ::= { cl2DevMonActiveTable 1 } Cl2DevMonActiveEntry ::= SEQUENCE { cl2DevMonActiveMacAddress MacAddress, cl2DevMonActivePollingFrequency Unsigned32, cl2DevMonActivePollingTimeOut Unsigned32, cl2DevMonActiveRowStatus RowStatus, cl2DevMonActiveRadioMacType INTEGER, cl2DevMonActiveLocalRadioIndex InterfaceIndex } cl2DevMonActiveMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Mac address of the active unit to be monitored by this hot standby monitoring unit." ::= { cl2DevMonActiveEntry 1 } cl2DevMonActivePollingFrequency OBJECT-TYPE SYNTAX Unsigned32 (1..30) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The frequency, in seconds, the active unit specified by cl2DevMonActiveMacAddress is polled for its health." DEFVAL { 5 } ::= { cl2DevMonActiveEntry 2 } cl2DevMonActivePollingTimeOut OBJECT-TYPE SYNTAX Unsigned32 (1..600) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The total time, in seconds, the standby monitoring unit can tolerate the failure of polling of the active unit. After this duration, one more failure of the polling will trigger this hot standby monitoring unit to take over and become an active unit. It then will stop monitoring other active units and set value of cl2DevMonInStandbyMode to FALSE." DEFVAL { 5 } ::= { cl2DevMonActiveEntry 3 } cl2DevMonActiveRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status column used for creating, modifying, and deleting instances of the columnar objects in the cl2DevMonActiveTable table. Creation of rows must be done via 'createAndGo' and all columns are mandatory. This object will become 'active' if the NMS performs a multivarbind set including this object. Any object in a row can be modified any time when the row is in the 'active' state. Removal of a row can be done via setting this object to 'destroy'." ::= { cl2DevMonActiveEntry 4 } cl2DevMonActiveRadioMacType OBJECT-TYPE SYNTAX INTEGER { ieee802dot11a(1), ieee802dot11b(2), ieee802dot11g(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "If the device being monitored is a IEEE 802.11 Wireless device, cl2DevMonActiveMacAddress is the remote device radio MAC address and this is the type of IEEE 802.11 Standard applies that radio: ieee802dot11a(1) - IEEE 802.11a Standard, ieee802dot11b(2) - IEEE 802.11b Standard, ieee802dot11g(3) - IEEE 802.11g Standard. If the device being monitored is not a IEEE 802.11 Wireless device, the default value for this object is '0'." REFERENCE "IEEE P802.11g (expected June 2003), Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications: Higher Speed Physical Layer (PHY) Extension to IEEE 802.11b." ::= { cl2DevMonActiveEntry 5 } cl2DevMonActiveLocalRadioIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-create STATUS current DESCRIPTION "If the device being monitored is a IEEE 802.11 Wireless LAN device, this is the ifIndex of a local radio of ifType ieee80211(71) used for the monitoring. If the local radio only supports to monitor only one remote radio, adding or updating multiple rows to the same ifIndex is not allowed." ::= { cl2DevMonActiveEntry 6 } -- ***************************************************************** -- notifications -- ***************************************************************** ciscoL2DevMonMIBNotifications OBJECT IDENTIFIER ::= { ciscoL2DevMonMIB 0 } cl2DevMonSwitchover NOTIFICATION-TYPE OBJECTS { cl2DevMonActivePollingFrequency, cl2DevMonActivePollingTimeOut } STATUS current DESCRIPTION "This cl2DevMonSwitchover notification will only be sent when this device changes its cl2DevMonInStandbyMode to FALSE and becomes an active unit. The sending of these notifications can be enabled/disabled via the cl2DevMonNotifEnabled object." ::= { ciscoL2DevMonMIBNotifications 1 } -- ***************************************************************** -- Conformance information -- ***************************************************************** ciscoL2DevMonMIBConformance OBJECT IDENTIFIER ::= { ciscoL2DevMonMIB 2 } ciscoL2DevMonMIBCompliances OBJECT IDENTIFIER ::= { ciscoL2DevMonMIBConformance 1 } ciscoL2DevMonMIBGroups OBJECT IDENTIFIER ::= { ciscoL2DevMonMIBConformance 2 } -- ***************************************************************** -- Compliance statements -- ***************************************************************** ciscoL2DevMonCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the ciscoL2DevMonConfig group." MODULE MANDATORY-GROUPS { ciscoL2DevMonConfigGroup, ciscoL2DevMonNotificationGroup } ::= { ciscoL2DevMonMIBCompliances 1 } ciscoL2DevMonComplianceRev1 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for the ciscoL2DevMonConfig group." MODULE MANDATORY-GROUPS { ciscoL2DevMonConfigGroup, ciscoL2DevMonNotificationGroup } GROUP ciscoL2DevMonRadioConfigGroup DESCRIPTION "Implementation of this group is required when object cl2DevMonActiveRadioMacType value is one of the IEEE 802.11 MAC protocol." ::= { ciscoL2DevMonMIBCompliances 2 } -- ***************************************************************** -- Units of conformance -- ***************************************************************** ciscoL2DevMonConfigGroup OBJECT-GROUP OBJECTS { cl2DevMonInStandbyMode, cl2DevMonNotifEnabled, cl2DevMonActivePollingFrequency, cl2DevMonActivePollingTimeOut, cl2DevMonActiveRowStatus } STATUS current DESCRIPTION "Management information to support operation of L2 monitoring and hot standby." ::= { ciscoL2DevMonMIBGroups 1 } ciscoL2DevMonNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { cl2DevMonSwitchover } STATUS current DESCRIPTION "The notifications for the CISCO-L2-DEV-MONITORING-MIB" ::= { ciscoL2DevMonMIBGroups 2 } ciscoL2DevMonRadioConfigGroup OBJECT-GROUP OBJECTS { cl2DevMonActiveRadioMacType, cl2DevMonActiveLocalRadioIndex } STATUS current DESCRIPTION "Management information to identify the MAC type of a IEEE 802.11 Wireless LAN device and local radio ifIndex." ::= { ciscoL2DevMonMIBGroups 3 } END