-- ********************************************************************* -- CISCO-IVR-MIB.my: Inter Virutal Storage Area Network (Inter-VSAN) -- Routing MIB -- -- July 2003, Vinay Gaonkar -- November 2004, John Fan -- -- Copyright (c) 2003, 2004, 2005 by cisco Systems, Inc. -- All rights reserved. -- -- ********************************************************************* CISCO-IVR-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Integer32, Unsigned32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF TEXTUAL-CONVENTION, RowStatus, TruthValue, TimeStamp FROM SNMPv2-TC ciscoMgmt FROM CISCO-SMI SnmpAdminString FROM SNMP-FRAMEWORK-MIB vsanIndex FROM CISCO-VSAN-MIB FcList, ZoneQosPriorityLevel FROM CISCO-ZS-MIB VsanIndex, FcNameId, DomainId, FcAddressId FROM CISCO-ST-TC; ciscoIvrMIB MODULE-IDENTITY LAST-UPDATED "200503030000Z" ORGANIZATION "Cisco Systems Inc." CONTACT-INFO " Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553 -NETS E-mail: cs-san@cisco.com" DESCRIPTION "The MIB module for the management of Inter-VSAN routing within the framework of Cisco's Inter-VSAN Routing (IVR) Architecture. IVR allows traffic between VSANs. VSANs are logically separated Storage Area Networks (SANs) where traffic does not cross VSAN boundaries. Certain SAN applications need restricted communication between initiators and targets which are in different VSANs. This MIB enables the users to manage IVR. The VSANs logically separate a single physical fabric into multiple logical fabrics. Each of these physical fabrics are called Autonmous Fabrics. In addition to Inter-VSAN communication, IVR also enables communication between Autonomous Fabrics. Acronyms The following acronyms are used in this document: Lun: Logical Unit Number IV: Inter-VSAN IVR: Inter-VSAN Routing PWWN: Port World Wide Name AFID: Autonomous Fabric id " REVISION "200503030000Z" DESCRIPTION "To support IVR-2 protocol, 1.added new objects civrFcidNatMode, civrVsanTopologyAutoDisc and civrTopologyIvrSrvGrpNextIndex. 2.added new objects to civrZoneMemberTable, civrZoneEnforcedZoneMemberTable, civrZoneTable and civrZoneEnforcedZoneTable. 3.added new tables, civrTopologyAfidConfTable, civrTopologyDefaultAfidTable, and civrTopologyIvrSrvGrpTable. 4.added new compliances. Added new values to eumeration provided by the civrZoneSetActvatDeactvatResult object." REVISION "200410270000Z" DESCRIPTION "Added new objects civrAddIvrVirtualDomainsVsans2k and civrAddIvrVirtualDomainsVsans4k. Added new compliance civrZoneServerMIBComplianceRev1." REVISION "200311030000Z" DESCRIPTION "Obtained new OID. Removed civEnabled object. Added notification civrDomainConflictNotify. Added objects civDomainIdConflictVsan, civrZoneMemberFabricId, civrZoneSetActDeactPartialSucss to be sent with notifications. Added few more enumerations to ivrZonesetStatus and civrZoneSetActvatDeactvatResult." REVISION "200310200000Z" DESCRIPTION "Initial version of this MIB." ::= { ciscoMgmt 371 } ciscoIvrMIBNotifications OBJECT IDENTIFIER ::= { ciscoIvrMIB 0 } ciscoIvrMIBObjects OBJECT IDENTIFIER ::= { ciscoIvrMIB 1 } ciscoIvrMIBConformance OBJECT IDENTIFIER ::= { ciscoIvrMIB 2 } cimIvrConfiguration OBJECT IDENTIFIER ::= { ciscoIvrMIBObjects 1 } cimIvrStats OBJECT IDENTIFIER ::= { ciscoIvrMIBObjects 2 } cimIvrGeneric OBJECT IDENTIFIER ::= { cimIvrConfiguration 1 } cimIvrZoneset OBJECT IDENTIFIER ::= { cimIvrConfiguration 2 } cimIvrZone OBJECT IDENTIFIER ::= { cimIvrConfiguration 3 } cimIvrZoneMember OBJECT IDENTIFIER ::= { cimIvrConfiguration 4 } cimIvrTopology OBJECT IDENTIFIER ::= { cimIvrConfiguration 5 } cimIvrVirtualDomains OBJECT IDENTIFIER ::= { cimIvrConfiguration 6 } -- Textual conventions CIvrZoneMemberType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Type of IV zone member. pwwnVsan - the member is identified by port WWN (World Wide Name) and VSAN." SYNTAX INTEGER { pwwnVsan(1) } CIvrAutonomousFabricId ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The Autonomous Fabric identifier. This identifies a set of fibre channel devices like hosts, disks, switches which are under single administration. It is up to the administrator to assign these identifiers to the Autonomous Fabrics so that each of the physical fabrics are uniquely identified. If a fabric is not partitioned into Autonomous Fabrics, then value of 1 must be used." SYNTAX Unsigned32 (1..65535) CIvrChecksum ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The checksum computed from the object/group of objects specified in the object description. This is used by manager to check if the object or group of objects is same across devices in the fabric. Note that method use to compute this is implementation specific." SYNTAX OCTET STRING (SIZE(1..255)) -- -- IVR Generic Configurations -- civrFcidNatMode OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Enable FCID and VSAN identifier translation cross VSAN boundaries. If the value is 'true', the VSAN identifier as well as the entire FCID of the end-devices would be modified as frames cross VSAN boundaries." ::= { cimIvrGeneric 1 } civrVsanTopologyAutoDisc OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Enable automatic VSAN topology discovery. If this value is 'true', automatic VSAN topology discovery is turned on. IVR processes would communicate with each other to provide a global view of the physical topology to all the IVR enabled switches. VSAN topology is configured through civrTopologyAfidConfTable and civrTopologyDefaultAfidTable when automatic VSAN topology discovery is turned on. If this value is 'false', automatic VSAN topology discovery is turned off. VSAN topology is manually configured by using civrTopologyConfigTable." ::= { cimIvrGeneric 2 } -- -- IVR zoneset configuration -- civrZoneSetNumber OBJECT-TYPE SYNTAX Integer32 (0..8388608) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of entries currently present in the civrZoneSetTable." ::= { cimIvrZoneset 1 } -- -- IV Zoneset configuration -- civrZoneSetTable OBJECT-TYPE SYNTAX SEQUENCE OF CivrZoneSetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing information on each Inter-VSAN (IV) zonesets which are configured locally. It comprises the zonesets in the full IV zone database. There could be multiple IV zonesets configured. But only one zoneset is allowed to be active at a time. An IV zoneset is a collection of IV zones." ::= { cimIvrZoneset 2 } civrZoneSetEntry OBJECT-TYPE SYNTAX CivrZoneSetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the civrZoneSetTable. The sequence of operations to be performed in order to create a zoneset is as follows: - create zone entries in the civrZoneTable. - create an entry in this table and set the civrZoneSetZoneList bitmap object to contain the required IV zones. - Note that it is perfectly valid to create an empty zoneset." INDEX { civrZoneSetIndex } ::= { civrZoneSetTable 1 } CivrZoneSetEntry ::= SEQUENCE { civrZoneSetIndex Unsigned32, civrZoneSetName SnmpAdminString, civrZoneSetZoneList FcList, civrZoneSetLastChange TimeStamp, civrZoneSetChecksum CIvrChecksum, civrZoneSetRowStatus RowStatus } civrZoneSetIndex OBJECT-TYPE SYNTAX Unsigned32 (1..2048) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of a zoneset. This object uniquely identifies an IV zoneset. This object could have the same value as civrZoneSetTableNextIndex." ::= { civrZoneSetEntry 1 } civrZoneSetName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..64)) MAX-ACCESS read-create STATUS current DESCRIPTION "The name of this zoneset. The civrZoneSetName should be unique on this device. This object cannot be modified while the corresponding value of civrZoneSetRowStatus is equal to 'active'. This object MUST be set before or concurrently with setting the corresponding instance of civrZoneSetRowStatus to 'active'." ::= { civrZoneSetEntry 2 } civrZoneSetZoneList OBJECT-TYPE SYNTAX FcList MAX-ACCESS read-create STATUS current DESCRIPTION "The set of IV zones which form this zoneset. The IV zones are identified by civrZoneIndex object in the civrZoneTable. If a particular bit has a value of '1', then the corresponding zone is a part of this zoneset. All other zones have '0' in their positions or not present in the string. Note that an IV zone can be part of multiple IV zonesets." DEFVAL { ''H } ::= { civrZoneSetEntry 3 } civrZoneSetLastChange OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time of the last change to this IV zoneset entry. If the entry has not been modified since the last re-initialization of the local network management system, then this object will contain a zero value." ::= { civrZoneSetEntry 4 } civrZoneSetChecksum OBJECT-TYPE SYNTAX CIvrChecksum MAX-ACCESS read-only STATUS current DESCRIPTION "The checksum of content of this zoneset." ::= { civrZoneSetEntry 5 } civrZoneSetRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. This object can not be set to 'active' unless the corresponding value of civrZoneSetName is unique." ::= { civrZoneSetEntry 6 } -- -- IV Zoneset Activation -- civrZoneSetActivate OBJECT-TYPE SYNTAX Unsigned32 (0..2048) MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to a value is a request for a particular IV zoneset to be activated on this device. i.e., for the current configuration of that zoneset to be cloned with the clone becoming the active zoneset. Setting this object to a value (say, N) identifies the IV zoneset to be cloned as the zoneset identified by civrZoneSetIndex object having the same value N. Even though there could be multiple IV zonesets on this device, only one can be active at a time. If a IV zoneset is already active and a second IV zone set is activated, then the first IV zoneset is automatically deactivated and the second IV zoneset is activated. The IV zoneset activation is done only in 'activate VSANs' on the local device. The 'activate VSANs' is the intersection of topology VSANs on the local device (civrTopologyActiveSwitchVsan2k and civrTopologyActiveSwitchVsan4k), members VSANs (union of all the VSANs of the members in the zoneset being activated) and local VSANs (vsanTable from CISCO-VSAN-MIB). If the activation was successful then, civrZoneEnforcedZoneSetName contains the name of zoneset corresponding to the civrZoneSetIndex that was set. The value of this object when read is always 0." ::= { cimIvrZoneset 3 } civrZoneSetActvatDeactvatResult OBJECT-TYPE SYNTAX INTEGER { activateSuccess (1), activateFailureNoMembers (2), activateFailureZoneOneorLessMem (3), activateFailureNoTopology (4), activateFailureNoPerVsanSucc (5), activateFailureNoZoneset (6), activateFailureNoVsans (7), activateFailureFabricUnstable (8), deactivateSuccess (9), deactivateFailureNoActiveZs (10), deactivateFailureNoPerVsanSucc (11), deactivateFailureFabricUnstable (12), activating (13), deactivating (14), idle (15), deactivateSuccessFcNatShutup13 (16), activateFailureFabric (17), deactivateFailureFabric (18), activatePartialSuccessFabric (19), deactivatePartialSuccessFabric (20), deviceCleanupInProgress (21), activatingReadyToAdv (22), activatingAdvertising (23) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the outcome of the most recent activation/deactivation. activateSuccess - activation success activateFailureNoMembers - activation failure because of no members in the zoneset activateFailureZoneOneorLessMem - activation failure as the zoneset being activated contained one or less member. activateFailureNoTopology - activation failure because of no IVR topology activateFailureNoPerVsanSucc - activation failed in all 'activate VSANs' activateFailureNoZoneset - activation failure because of no zoneset activateFailureNoVsans - activation failure because of no 'activate VSANs' activateFailureFabricUnstable - activation failure because fabric unstable deactivateSuccess - deactivation success deactivateFailureNoActiveZs - no active zoneseset deactivateFailureNoPerVsanSucc - deactivation failed in all 'activate VSANs' deactivateFailureFabricUnstable - deactivation failed because fabric is unstable activating - activation in progress deactivating - deactivation in progress idle - idle deactivateSuccessFcNatShutup13 - deactivation success, shutup 1.3 switch in NAT mode activateFailureFabric - none of the switches connected to the fabric is able to activate this zoneset deactivateFailureFabric - none of the switches connected to the fabric is able to deactivate this zoneset activatePartialSuccessFabric - activation succeeds on some of the switches connected to this fabric deactivatePartialSuccessFabric - deactivation succeeds on some of the switches connected to this fabric deviceCleanupInProgress - device cleanup is in progress during deactivation activatingReadyToAdv - switches connected to this fabric are ready to advertise device changes activatingAdvertising - switches connected to this fabric are advertising device change information When the value of this object is either 'activating', or 'deactivating', the values of of civrZoneSetActivate and civrZoneSetDeActivate respectively cannot be modified." ::= { cimIvrZoneset 4 } civrZoneSetDeActivate OBJECT-TYPE SYNTAX INTEGER { deactivate(1), -- deactivate IV zoneset noop(2) -- no operation } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to 'deactivate' is a request to deactivate the currently active IV zoneset. deactivate - deactivate IV zoneset noop - no operation No action is taken if this object is set to 'noop'. The value of this object when read is always 'noop'." ::= { cimIvrZoneset 5 } civrZonesetDbChecksum OBJECT-TYPE SYNTAX CIvrChecksum MAX-ACCESS read-only STATUS current DESCRIPTION "The checksum of the full IV zone database." ::= { cimIvrZoneset 6 } civrActiveZonesetChecksum OBJECT-TYPE SYNTAX CIvrChecksum MAX-ACCESS read-only STATUS current DESCRIPTION "The checksum of the enforced (active) IV zoneset." ::= { cimIvrZoneset 7 } -- -- IV Zone objects -- civrZoneNumber OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of entries currently present in the civrZoneTable." ::= { cimIvrZone 1 } -- -- civrZoneTable -- civrZoneTable OBJECT-TYPE SYNTAX SEQUENCE OF CivrZoneEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table gives information on all the IV zones and lists all their members. IV zones is group of IV members (FC devices like hosts, disks) in different VSANs." ::= { cimIvrZone 2 } civrZoneEntry OBJECT-TYPE SYNTAX CivrZoneEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the civrZoneTable. These are the zones in the full IV zone database. The sequence of operations to be performed in order to create a IV Zone is as follows: - create an entry in this table. - create IV zone members in the civrZoneMemberTable that belong to this IV zone." INDEX { civrZoneIndex } ::= { civrZoneTable 1 } CivrZoneEntry ::= SEQUENCE { civrZoneIndex Unsigned32, civrZoneName SnmpAdminString, civrZoneMemberList FcList, civrZoneLastChange TimeStamp, civrZoneRowStatus RowStatus, civrZoneReadOnly TruthValue, civrZoneQosPriority ZoneQosPriorityLevel } civrZoneIndex OBJECT-TYPE SYNTAX Unsigned32 (1..2048) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of an IV Zone. This object could have the same value as civrZoneTableNextIndex." ::= { civrZoneEntry 1 } civrZoneName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..58)) MAX-ACCESS read-create STATUS current DESCRIPTION "The name of this zone. The zoneName should be unique this device. This object can not be modified while the corresponding value of civrZoneRowStatus is 'active'. This object MUST be set before or concurrently with setting the corresponding instance of civrZoneRowStatus to 'active'." ::= { civrZoneEntry 2 } civrZoneMemberList OBJECT-TYPE SYNTAX FcList MAX-ACCESS read-only STATUS current DESCRIPTION "The set of IV Zone members that form this IV zone. The IV zone members are identified by civrZoneMemberIndex object in the civrZoneMemberTable. If a particular bit has a value of '1', then the corresponding zone member is a part of this zone. All other zone members have '0' in their positions or not present in the string. This object is read-only; changes to its value are made by the agent as and when associated entries are created/deleted in the civrZoneMemberTable. The default value is the zero length string." DEFVAL { ''H } ::= { civrZoneEntry 3 } civrZoneLastChange OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time of the last change to this IV zone entry. If the entry has not been modified since the last re-initialization of the local network management system, then this object will contain a zero value." ::= { civrZoneEntry 5 } civrZoneRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. This object can not be set to 'active' unless the corresponding value of zoneName is unique on this device." ::= { civrZoneEntry 6 } civrZoneReadOnly OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates if only SCSI read operations are allowed on members of this IV zone which are SCSI targets. If this object is set to 'true', then only SCSI read operations are permitted. So, this IV zone becomes a read-only IV zone. If this object is set to 'false', then both SCSI read and write operations are permitted in this IV zone." ::= { civrZoneEntry 7 } civrZoneQosPriority OBJECT-TYPE SYNTAX ZoneQosPriorityLevel MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies if qos attribute for this IV zone is enabled. If this object is set to a value other than 'none', then qos attribute for this IV zone is enabled. If this object is set to 'none', then qos attribute for this IV zone is disabled. If this attribute is enabled for this IV zone, then only traffic with the configured priority level will be allowed between the members of this IV zone." ::= { civrZoneEntry 8 } -- -- civrZoneMemberTable -- civrZoneMemberNumber OBJECT-TYPE SYNTAX Integer32 (0..16777216) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of entries currently present in the civrZoneMemberTable." ::= { cimIvrZoneMember 1 } civrZoneMemberTable OBJECT-TYPE SYNTAX SEQUENCE OF CivrZoneMemberEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains all members of all the IV Zones in the civrZoneTable and information about those members. These are the members part of full IV zone database." ::= { cimIvrZoneMember 2 } civrZoneMemberEntry OBJECT-TYPE SYNTAX CivrZoneMemberEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the civrZoneMemberTable. Each entry represents the relationship between a member and (one of) its 'parent(s)', i.e., an IV zone to which the member belongs to." INDEX { civrZoneMemberParentIndex, civrZoneMemberIndex } ::= { civrZoneMemberTable 1 } CivrZoneMemberEntry ::= SEQUENCE { civrZoneMemberParentIndex Unsigned32, civrZoneMemberIndex Unsigned32, civrZoneMemberType CIvrZoneMemberType, civrZoneMemberID OCTET STRING, civrZoneMemberAFId CIvrAutonomousFabricId, civrZoneMemberVsan VsanIndex, civrZoneMemberRowStatus RowStatus, civrZoneMemberLunID OCTET STRING } civrZoneMemberParentIndex OBJECT-TYPE SYNTAX Unsigned32 (1..2048) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object contains the value of the index of the IV zone to which this member belongs to." ::= { civrZoneMemberEntry 1 } civrZoneMemberIndex OBJECT-TYPE SYNTAX Unsigned32 (1..2048) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of this IV zone member on this IV zone." ::= { civrZoneMemberEntry 2 } civrZoneMemberType OBJECT-TYPE SYNTAX CIvrZoneMemberType MAX-ACCESS read-create STATUS current DESCRIPTION "The type of IV Zone member. This object cannot be modified while the corresponding value of civrZoneMemberRowStatus object is 'active'." ::= { civrZoneMemberEntry 3 } civrZoneMemberID OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the IV zone member ID. If civrZoneMemberType is 'pwwnVsan', this object contains port WWN. This object cannot be modified while the corresponding value of civrZoneMemberRowStatus object is 'active'." ::= { civrZoneMemberEntry 4 } civrZoneMemberAFId OBJECT-TYPE SYNTAX CIvrAutonomousFabricId MAX-ACCESS read-create STATUS current DESCRIPTION "The Autonomous Fabric identifier of this IV zone member. This object cannot be modified while the corresponding value of civrZoneMemberRowStatus object is 'active'." DEFVAL { 1 } ::= { civrZoneMemberEntry 5 } civrZoneMemberVsan OBJECT-TYPE SYNTAX VsanIndex MAX-ACCESS read-create STATUS current DESCRIPTION "The VSAN of this IV zone member. This object cannot be modified while the corresponding value of civrZoneMemberRowStatus object is 'active'." ::= { civrZoneMemberEntry 6 } civrZoneMemberRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. civrMemberType, civrZoneMemberID and civrZoneMemberVsan objects MUST be set before or concurrently with setting the corresponding instance of civrZoneMemberRowStatus to 'active'. " ::= { civrZoneMemberEntry 7 } civrZoneMemberLunID OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0 | 8)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the Lun ID if IV Lun zoning is configured. If this object is the zero-length string, then IV Lun zoning is not configured. This object cannot be modified while the corresponding value of zoneMemberRowStatus object is 'active'." DEFVAL { ''H } ::= { civrZoneMemberEntry 8 } -- -- Enforced zoneset -- civrZoneEnforcedZoneSetName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the enforced IV zoneset." ::= { cimIvrZoneset 8 } civrZoneEnforcedZoneSetZoneList OBJECT-TYPE SYNTAX FcList MAX-ACCESS read-only STATUS current DESCRIPTION "The set of IV zones which form this IV zoneset. This object was copied from the civrZoneSetZoneList object in the civrZoneSetTable at the time when the currently active zoneset was activated." ::= { cimIvrZoneset 9 } civrZoneEnforcedZoneSetActvtTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The sysUpTime at which enforced zoneset was most recently activated. If this entry has been activated prior to the last re-initialization of the local network management system, then this object will contain a zero value." ::= { cimIvrZoneset 10 } civrZoneCopyZoneSetEnforcdToFull OBJECT-TYPE SYNTAX INTEGER { copy (1), noOp (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object copies the enforced IV zoneset (active IV zoneset) into the full IV zone database Setting this object to 'copy' will trigger the copy of the enforced IV zoneset to the full IV zone database. If there is no enforced IV zoneset, the copy will result in an error. No action is taken if this object is set to 'noOp'." ::= { cimIvrZoneset 11 } civrZoneClearFullZoneDb OBJECT-TYPE SYNTAX INTEGER { clear (1), noOp (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object clears the full IVR zone database. Setting this object to 'clear' will clear the full IV zone database. No action is taken if this object is set to 'noOp'." ::= { cimIvrZoneset 12 } civrZonesetActivateForce OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The force option for IV zoneset activation. Following things are done if this object is 'true': - If there is no regular active zoneset in a VSAN (no entry present zoneEnforcedZoneSetTable from CISCO-ZS-MIB for that VSAN), then a regular active zoneset will be created and the IV zones will be added to the active zoneset. - if the default zone behaviour (as indicated by object zoneDefaultZoneBehaviour from CISCO-ZS-MIB) is 'permit', then the IV zones will be added to the regular active zoneset. If the value of this object is 'false', the IV zones are added to the regular active zoneset only in the case of default zone behaviour is 'deny'." ::= { cimIvrZoneset 13 } civrZoneSetTableNextIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the next available index for object civrZoneSetIndex which can be used for creating an entry in civrZoneSetTable." ::= { cimIvrZoneset 14 } -- -- enforced zone -- civrZoneEnforcedZoneNumber OBJECT-TYPE SYNTAX Integer32 (0..8388608) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of entries currently present in the civrZoneEnforcedZoneTable." ::= { cimIvrZone 3 } civrZoneEnforcedZoneTable OBJECT-TYPE SYNTAX SEQUENCE OF CivrZoneEnforcedZoneEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains all the IV zones that are present in the active IV zoneset." ::= { cimIvrZone 4 } civrZoneEnforcedZoneEntry OBJECT-TYPE SYNTAX CivrZoneEnforcedZoneEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in this table." INDEX { civrZoneIndex } ::= { civrZoneEnforcedZoneTable 1 } CivrZoneEnforcedZoneEntry ::= SEQUENCE { civrZoneEnforcedZoneName SnmpAdminString, civrZoneEnforcedZoneMemberList FcList, civrZoneEnforcedZoneReadOnly TruthValue, civrZoneEnforcedZoneQosPriority ZoneQosPriorityLevel } civrZoneEnforcedZoneName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..58)) MAX-ACCESS read-only STATUS current DESCRIPTION "The name of this zone." ::= { civrZoneEnforcedZoneEntry 1 } civrZoneEnforcedZoneMemberList OBJECT-TYPE SYNTAX FcList MAX-ACCESS read-only STATUS current DESCRIPTION "The set of members that form this IV zone. This object was copied from the civrZoneMemberList object in the civrZoneTable at the time when the currently active zoneset was activated." ::= { civrZoneEnforcedZoneEntry 2 } civrZoneEnforcedZoneReadOnly OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether this is a read-only IV zone. This object was copied from the civrZoneReadOnly object in the civrZoneTable at the time when the currently active zoneset was activated." ::= { civrZoneEnforcedZoneEntry 3 } civrZoneEnforcedZoneQosPriority OBJECT-TYPE SYNTAX ZoneQosPriorityLevel MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether this is a qos enabled IV zone. This object was copied from the civrZoneQosPriority object in the civrZoneTable at the time when the currently active zoneset was activated." ::= { civrZoneEnforcedZoneEntry 4 } civrZoneTableNextIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the next available index for object civrZoneIndex which can be used for creating an entry in civrZoneTable." ::= { cimIvrZone 5 } -- -- enforced IV zone member -- civrZoneEnforcedZoneMemberNumber OBJECT-TYPE SYNTAX Integer32 (0..16777216) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of entries currently present in the civrZoneEnforcedZoneMemberTable." ::= { cimIvrZoneMember 3 } civrZoneEnforcedZoneMemberTable OBJECT-TYPE SYNTAX SEQUENCE OF CivrZoneEnforcedZoneMemberEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains all members that are part of a IV zone and are part of the active IV zone set." ::= { cimIvrZoneMember 4 } civrZoneEnforcedZoneMemberEntry OBJECT-TYPE SYNTAX CivrZoneEnforcedZoneMemberEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in this table." INDEX { civrZoneMemberParentIndex, civrZoneMemberIndex } ::= { civrZoneEnforcedZoneMemberTable 1 } CivrZoneEnforcedZoneMemberEntry ::= SEQUENCE { civrZoneEnforcedZoneMemberType CIvrZoneMemberType, civrZoneEnforcedZoneMemberID OCTET STRING, civrZoneEnforcedZoneMemberAFId CIvrAutonomousFabricId, civrZoneEnforcedZoneMemberVsan VsanIndex, civrZoneEnforcedZoneMemberLunID OCTET STRING } civrZoneEnforcedZoneMemberType OBJECT-TYPE SYNTAX CIvrZoneMemberType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of IV zone member. This object was copied from the civrZoneMemberType object in the civrZoneMemberTable at the time when the currently active zoneset was activated." ::= { civrZoneEnforcedZoneMemberEntry 2 } civrZoneEnforcedZoneMemberID OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents this member's address. This object was copied from the civrZoneMemberID object in the civrZoneMemberTable at the time when the currently active zoneset was activated." ::= { civrZoneEnforcedZoneMemberEntry 3 } civrZoneEnforcedZoneMemberAFId OBJECT-TYPE SYNTAX CIvrAutonomousFabricId MAX-ACCESS read-only STATUS current DESCRIPTION "The Autonomous Fabric identifier of the member. This object was copied from the civrZoneMemberAFId object in the civrZoneMemberTable at the time when the currently active zoneset was activated." ::= { civrZoneEnforcedZoneMemberEntry 4 } civrZoneEnforcedZoneMemberVsan OBJECT-TYPE SYNTAX VsanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The VSAN of the member. This object was copied from the civrZoneMemberVsan object in the civrZoneMemberTable at the time when the currently active zoneset was activated." ::= { civrZoneEnforcedZoneMemberEntry 5 } civrZoneEnforcedZoneMemberLunID OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0 | 8)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the Lun ID if IV Lun zoning is configured. This object was copied from the civrZoneMemberLunID object in the civrZoneMemberTable at the time when the currently active zoneset was activated." ::= { civrZoneEnforcedZoneMemberEntry 6 } -- -- Inter VSAN Zoneset Status -- civrZoneSetStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF CivrZoneSetStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing status of the current active IV Zoneset on each local VSANs." ::= { cimIvrStats 1 } civrZoneSetStatusEntry OBJECT-TYPE SYNTAX CivrZoneSetStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the civrZoneSetStatusTable." INDEX { vsanIndex } ::= { civrZoneSetStatusTable 1 } CivrZoneSetStatusEntry ::= SEQUENCE { civrZoneSetStatus INTEGER } civrZoneSetStatus OBJECT-TYPE SYNTAX INTEGER { idle(1), active (2), deactive (3), defaultZoneDeny (4), activationFailed (5), deactivationFailed (6), activationNotInitiated (7), activationFailedFabricChgFailed (8), deactivationNotInitiated (9), deactivationFailedFabChgFailed (10), activating (11), activatingWaitForLowestSwwn (12), activatingFabricChanging(13), deactivating (14), deactivatingWaitForLowestSwwn (15), deactivatingFabricChanging (16), defaultZonePermit (17), defaultZonePermitNoForce (18), defaultZonePermitActZsNoForce (19), denyNoActiveZoneset(20), activationFailedLowestWwnWait(21), deactivationFailedLowestWwnWait(22) } MAX-ACCESS read-only STATUS current DESCRIPTION "Status of the active IV Zoneset on this VSAN. idle - idle active - active deactive - deactive defaultZoneDeny - activation failed because of default zone behaviour is deny and there is no regular active zoneset. activationFailed - activation failed (check zoneSetFailCause in CISCO-ZS-MIB for this VSAN) deactivationFailed - deactivation failed (check zoneSetFailCause in CISCO-ZS-MIB for this VSAN) activationNotInitiated - activation not initiated activationFailedFabricChgFailed - activation failed because of fabric change failed deactivationNotInitiated - deactivation not initiated deactivationFailedFabChgFailed - deactivation failed because of fabric changing activating - activation in progress activatingWaitForLowestSwwn - activation in progress; waiting for the lowest switch WWN switch to add IV zoneset to the regular active zoneset. activatingFabricChanging - activation in progress; fabric is changing deactivating - deactivation in progress deactivatingWaitForLowestSwwn - deactivation in progress; waiting for the lowest switch WWN switch to delete IV zoneset from the regular active zoneset. deactivatingFabricChanging - deactivation in progress; fabric is changing defaultZonePermit - activation failed because of default zone behaviour is permit defaultZonePermitNoForce - activation failed because of default zone behaviour is permit with no force option defaultZonePermitActZsNoForce - activation failed because of default zone behaviour is permit and with regular activate zoneset and no force option denyNoActiveZoneset - activation failed because there is no active zoneset activationFailedLowestWwnWait - activation failed waiting for switch with lowest wwn to activate this zoneset deactivationFailedLowestWwnWait - deactivation failed waiting for switch with lowest wwn to deactivate this zoneset ." ::= { civrZoneSetStatusEntry 1 } -- -- IVR Topology table -- civrTopologyConfiguredChecksum OBJECT-TYPE SYNTAX CIvrChecksum MAX-ACCESS read-only STATUS current DESCRIPTION "The checksum of the configured IVR topology." ::= { cimIvrTopology 1 } civrTopologyConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF CivrTopologyConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the configured IVR topology. The topology is specified in terms of one or more Autonomous Fabrics made of switches and the VSANs to/from which the switches provide connectivity. The configured topology is not applied until it is made active using using object civrTopologyActivate." ::= { cimIvrTopology 2 } civrTopologyConfigEntry OBJECT-TYPE SYNTAX CivrTopologyConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in this table." INDEX { civrTopologyConfigAutoFabricId, civrTopologyConfigSwitchWwn } ::= { civrTopologyConfigTable 1 } CivrTopologyConfigEntry ::= SEQUENCE { civrTopologyConfigSwitchWwn FcNameId, civrTopologyConfigAutoFabricId CIvrAutonomousFabricId, civrTopologyConfigSwitchVsan2k FcList, civrTopologyConfigSwitchVsan4k FcList, civrTopologyConfigRowStatus RowStatus } civrTopologyConfigSwitchWwn OBJECT-TYPE SYNTAX FcNameId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The configured switch WWN of this device." ::= { civrTopologyConfigEntry 1 } civrTopologyConfigAutoFabricId OBJECT-TYPE SYNTAX CIvrAutonomousFabricId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The configured Autonomous Fabric id of this device." ::= { civrTopologyConfigEntry 2 } civrTopologyConfigSwitchVsan2k OBJECT-TYPE SYNTAX FcList MAX-ACCESS read-create STATUS current DESCRIPTION "The list of configured VSANs that are part of IVR topology on this device. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 0 through 7, the second octet specifying VSANs 8 through 15, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in the IVR topology on this device if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in this list. If the values of both this object and corresponding instance of civrTopologyConfigSwitchVsan4k are zero-length string, then the IVR topology contains only the default VSAN." DEFVAL {''H} ::= { civrTopologyConfigEntry 3 } civrTopologyConfigSwitchVsan4k OBJECT-TYPE SYNTAX FcList MAX-ACCESS read-create STATUS current DESCRIPTION "The list of configured VSANs that are part of IVR topology on this device. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 2047 through 2054, the second octet specifying VSANs 2055 through 2062, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in the IVR topology on device if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in the list. If the values of both this object and corresponding instance of civrTopologyConfigSwitchVsan2k are zero-length string, then the IVR topology contains only the default VSAN." DEFVAL {''H} ::= { civrTopologyConfigEntry 4 } civrTopologyConfigRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Status of this row." ::= { civrTopologyConfigEntry 5 } -- -- Topology activation -- civrTopologyActivate OBJECT-TYPE SYNTAX INTEGER { activate (1), noOp(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to 'activate' is a request for the configured IVR topology to be activated on this device. i.e., for the current configuration of IVR topology to be cloned, with the clone becoming the active IVR topology (civrTopologyActiveTable). The value of this object when read is always 'noOp'." ::= { cimIvrTopology 3} civrTopologyActivateTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The sysUpTime at which the IVR topology was most recently activated. If the IVR topology has not been activated prior to the last re-initialization of the local network management system, then this object will contain a zero value." ::= { cimIvrTopology 4 } civrTopologyCopyActiveToConfig OBJECT-TYPE SYNTAX INTEGER { copy (1), noOp (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object copies the active IVR topology table to configured IVR topology table. If there is no active IVR topology, the copy will result in an error. No action is taken if this object is set to 'noOp'." ::= { cimIvrTopology 5 } civrTopologyClearConfigured OBJECT-TYPE SYNTAX INTEGER { clear (1), noOp (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object clears the configured IVR topology table. No action is taken if this object is set to 'noOp'." ::= { cimIvrTopology 6 } -- -- Active IVR topology table -- civrTopologyActiveChecksum OBJECT-TYPE SYNTAX CIvrChecksum MAX-ACCESS read-only STATUS current DESCRIPTION "The checksum of the active IVR topology." ::= { cimIvrTopology 7 } civrTopologyActiveTable OBJECT-TYPE SYNTAX SEQUENCE OF CivrTopologyActiveEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the IVR topology. The topology is specified in terms of one or more Autonomous Fabrics made of switches and the VSANs to/from which the switches provide connectivity." ::= { cimIvrTopology 8 } civrTopologyActiveEntry OBJECT-TYPE SYNTAX CivrTopologyActiveEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in this table." INDEX { civrTopologyActiveAutoFabricId, civrTopologyActiveSwitchWwn } ::= { civrTopologyActiveTable 1 } CivrTopologyActiveEntry ::= SEQUENCE { civrTopologyActiveSwitchWwn FcNameId, civrTopologyActiveAutoFabricId CIvrAutonomousFabricId, civrTopologyActiveSwitchVsan2k FcList, civrTopologyActiveSwitchVsan4k FcList } civrTopologyActiveSwitchWwn OBJECT-TYPE SYNTAX FcNameId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The switch WWN of this device." ::= { civrTopologyActiveEntry 1 } civrTopologyActiveAutoFabricId OBJECT-TYPE SYNTAX CIvrAutonomousFabricId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Autonomous Fabric id of this device." ::= { civrTopologyActiveEntry 2 } civrTopologyActiveSwitchVsan2k OBJECT-TYPE SYNTAX FcList MAX-ACCESS read-only STATUS current DESCRIPTION "The list of VSANs that are part of IVR topology on this device. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 0 through 7, the second octet specifying VSANs 8 through 15, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in the IVR topology on this device if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in this list. If the values of both this object and corresponding instance of civrTopologyActiveSwitchVsan4k are zero-length string, then the IVR topology contains only the default VSAN." DEFVAL {''H} ::= { civrTopologyActiveEntry 3 } civrTopologyActiveSwitchVsan4k OBJECT-TYPE SYNTAX FcList MAX-ACCESS read-only STATUS current DESCRIPTION "The list of VSANs that are part of IVR topology on this device. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 2047 through 2054, the second octet specifying VSANs 2055 through 2062, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in the IVR topology on device if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in the list. If the values of both this object and corresponding instance of civrTopologyActiveSwitchVsan2k are zero-length string, then the IVR topology contains only the default VSAN." DEFVAL {''H} ::= { civrTopologyActiveEntry 4 } civrTopologyActive OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates of IVR topology is active or not. If 'true', the IVR topology is active. And if it is 'false', the IVR topology is not active." ::= { cimIvrTopology 9 } civrTopologyAfidConfigChecksum OBJECT-TYPE SYNTAX CIvrChecksum MAX-ACCESS read-only STATUS current DESCRIPTION "The checksum of the Autonomous Fabric id (AFID) configurations." ::= { cimIvrTopology 10 } civrTopologyAfidConfTable OBJECT-TYPE SYNTAX SEQUENCE OF CivrTopologyAfidConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the Autonomous Fabric id (AFID) configurations when automatic VSAN topology discovery is activated. An entry (conceptual row) in this table represents an AFID and its VSANs on a switch." ::= { cimIvrTopology 11 } civrTopologyAfidConfEntry OBJECT-TYPE SYNTAX CivrTopologyAfidConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in this table." INDEX { civrTopologyAfidConfSwitchWwn, civrTopologyAfidConfId } ::= { civrTopologyAfidConfTable 1 } CivrTopologyAfidConfEntry ::= SEQUENCE { civrTopologyAfidConfSwitchWwn FcNameId, civrTopologyAfidConfId CIvrAutonomousFabricId, civrTopologyAfidConfSwitchVsan2k FcList, civrTopologyAfidConfSwitchVsan4k FcList, civrTopologyAfidConfRowStatus RowStatus } civrTopologyAfidConfSwitchWwn OBJECT-TYPE SYNTAX FcNameId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The switch WWN of this device." ::= { civrTopologyAfidConfEntry 1 } civrTopologyAfidConfId OBJECT-TYPE SYNTAX CIvrAutonomousFabricId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The configured Autonomous Fabric id of this device." ::= { civrTopologyAfidConfEntry 2 } civrTopologyAfidConfSwitchVsan2k OBJECT-TYPE SYNTAX FcList MAX-ACCESS read-create STATUS current DESCRIPTION "The list of VSANs that are part of AFID (Autonomous Fabric ID) specified by civrTopologyConfigAutoFabricId on switch specified by civrTopologyConfigSwitchWwn. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 0 through 7, the second octet specifying VSANs 8 through 15, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in this AFID on this device if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in this list. If the values of both this object and corresponding instance of civrTopologyAfidConfSwitchVsan4k are zero-length string, then the AFID configured on this device contains only the default VSAN." DEFVAL {''H} ::= { civrTopologyAfidConfEntry 3 } civrTopologyAfidConfSwitchVsan4k OBJECT-TYPE SYNTAX FcList MAX-ACCESS read-create STATUS current DESCRIPTION "The list of VSANs that are part of AFID (Autonomous Fabric ID) specified by civrTopologyConfigAutoFabricId on switch specified by civrTopologyConfigSwitchWwn. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 2048 through 2054, the second octet specifying VSANs 2055 through 2062, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in this AFID on this device if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in this list. If the values of both this object and corresponding instance of civrTopologyAfidConfSwitchVsan2k are zero-length string, then the AFID configured on this device contains only the default VSAN." DEFVAL {''H} ::= { civrTopologyAfidConfEntry 4 } civrTopologyAfidConfRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Status of this row." ::= { civrTopologyAfidConfEntry 5 } civrTopologyDefaultAfidChecksum OBJECT-TYPE SYNTAX CIvrChecksum MAX-ACCESS read-only STATUS current DESCRIPTION "The checksum of the configured default AFIDs." ::= { cimIvrTopology 12 } civrTopologyDefaultAfidTable OBJECT-TYPE SYNTAX SEQUENCE OF CivrTopologyDefaultAfidEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the default Autonomous Fabric id (AFID) configurations when automatic VSAN topology discovery is activated. An entry (conceptual row) in this table represents the default AFID for a switch." ::= { cimIvrTopology 13 } civrTopologyDefaultAfidEntry OBJECT-TYPE SYNTAX CivrTopologyDefaultAfidEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in this table." INDEX { civrTopologyDefaultAfidSwitchWwn } ::= { civrTopologyDefaultAfidTable 1 } CivrTopologyDefaultAfidEntry ::= SEQUENCE { civrTopologyDefaultAfidSwitchWwn FcNameId, civrTopologyDefaultAfidId CIvrAutonomousFabricId, civrTopologyDefaultAfidStatus RowStatus } civrTopologyDefaultAfidSwitchWwn OBJECT-TYPE SYNTAX FcNameId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The switch WWN of this device." ::= { civrTopologyDefaultAfidEntry 1 } civrTopologyDefaultAfidId OBJECT-TYPE SYNTAX CIvrAutonomousFabricId MAX-ACCESS read-create STATUS current DESCRIPTION "The configured Default Autonomous Fabric id of this switch." DEFVAL { 1 } ::= { civrTopologyDefaultAfidEntry 2 } civrTopologyDefaultAfidStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Status of this row." ::= { civrTopologyDefaultAfidEntry 3 } civrTopologyIvrSrvGrpTable OBJECT-TYPE SYNTAX SEQUENCE OF CivrTopologyIvrSrvGrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains configurations of Inter-VSAN Routing (IVR) Service Group. An Inter VSAN Routing Service Group defines a logical boundary for Inter-VSAN Routing. Inter-VSAN Routing is restricted among VSANs within their own Inter-VSAN Routing Service Group only." ::= { cimIvrTopology 14 } civrTopologyIvrSrvGrpEntry OBJECT-TYPE SYNTAX CivrTopologyIvrSrvGrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in this table." INDEX { civrTopologyIvrSrvGrpName, civrTopologyAfidConfId } ::= { civrTopologyIvrSrvGrpTable 1 } CivrTopologyIvrSrvGrpEntry ::= SEQUENCE { civrTopologyIvrSrvGrpName SnmpAdminString, civrTopologyIvrSrvGrpVsan2k FcList, civrTopologyIvrSrvGrpVsan4k FcList, civrTopologyIvrSrvGrpRowStatus RowStatus } civrTopologyIvrSrvGrpName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..80)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object contains the name of the IVR Service Group corresponding to this conceptual row." ::= { civrTopologyIvrSrvGrpEntry 1 } civrTopologyIvrSrvGrpVsan2k OBJECT-TYPE SYNTAX FcList MAX-ACCESS read-create STATUS current DESCRIPTION "The list of VSANs that are part of this IVR Service Group specified by civrTopologyIvrSrvGrpName. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 0 through 7, the second octet specifying VSANs 8 through 15, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in this IVR Service Group if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in this list." ::= { civrTopologyIvrSrvGrpEntry 2 } civrTopologyIvrSrvGrpVsan4k OBJECT-TYPE SYNTAX FcList MAX-ACCESS read-create STATUS current DESCRIPTION "The list of VSANs that are part of this IVR Service Group specified by civrTopologyIvrSrvGrpName. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 2048 through 2054, the second octet specifying VSANs 2055 through 2062, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in this IVR Service Group if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in the list." ::= { civrTopologyIvrSrvGrpEntry 3 } civrTopologyIvrSrvGrpRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Status of this row." ::= { civrTopologyIvrSrvGrpEntry 4 } civrTopologyClearAfidConfig OBJECT-TYPE SYNTAX INTEGER { clear (1), noOp (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object clears the AFID configuration table, civrTopologyAfidConfTable, if this object is set to 'clear'. No action is taken if this object is set to 'noOp'." ::= { cimIvrTopology 15 } -- -- Virtual Domains -- civrAddIvrVirtualDomainsVsans2k OBJECT-TYPE SYNTAX FcList MAX-ACCESS read-write STATUS current DESCRIPTION "This object lists VSANs in which the virtual domains in a VSAN are added to the domain list (dmDatabaseTable in CISCO-DM-MIB) in that VSAN. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 0 through 7, the second octet specifying VSANs 8 through 15, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in the add virtual domain VSAN list on this device if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in this list. If the values of both this object and civrAddIvrVirtualDomainsVsans4k are zero-length string, then the Virtual Domains are not added to any VSANs." ::= { cimIvrVirtualDomains 1 } civrAddIvrVirtualDomainsVsans4k OBJECT-TYPE SYNTAX FcList MAX-ACCESS read-write STATUS current DESCRIPTION "This object lists VSANs in which the virtual domains in a VSAN are added to the domain list (dmDatabaseTable in CISCO-DM-MIB) in that VSAN. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 2048 through 2055, the second octet specifying VSANs 2056 through 2063, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in the add virtual domain VSAN list on device if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in the list. If the values of both this object and civrAddIvrVirtualDomainsVsans2k are zero-length string, then the Virtual Domains are not added to any VSANs." ::= { cimIvrVirtualDomains 2 } -- -- IVR Enabled devices -- civrEnabledDeviceTable OBJECT-TYPE SYNTAX SEQUENCE OF CivrEnabledDeviceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the all IVR enabled devices known to the local device on each of the local VSANs. Note that the devices are learned using an internal protocol. So if a device in this table is not reachable, anymore from the local switch, then it is removed from this table. Also, if a new device is learned, it is added to this table." ::= { cimIvrStats 2 } civrEnabledDeviceEntry OBJECT-TYPE SYNTAX CivrEnabledDeviceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in this table. Each entry represents a device in a particular VSAN." INDEX { civrEnabledDeviceAutoFabricId, civrEnabledDeviceVsan, civrEnabledDeviceDomainId } ::= { civrEnabledDeviceTable 1 } CivrEnabledDeviceEntry ::= SEQUENCE { civrEnabledDeviceVsan VsanIndex, civrEnabledDeviceAutoFabricId CIvrAutonomousFabricId, civrEnabledDeviceDomainId DomainId, civrEnabledDeviceSwitchWwn FcNameId, civrEnabledDeviceCapability BITS } civrEnabledDeviceVsan OBJECT-TYPE SYNTAX VsanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VSAN corresponding to this entry." ::= { civrEnabledDeviceEntry 1 } civrEnabledDeviceAutoFabricId OBJECT-TYPE SYNTAX CIvrAutonomousFabricId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Autonomous Fabric id corresponding to this entry." ::= { civrEnabledDeviceEntry 2 } civrEnabledDeviceDomainId OBJECT-TYPE SYNTAX DomainId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The domain ID of this device corresponding this entry." ::= { civrEnabledDeviceEntry 3 } civrEnabledDeviceSwitchWwn OBJECT-TYPE SYNTAX FcNameId MAX-ACCESS read-only STATUS current DESCRIPTION "The switch WWN of this device." ::= { civrEnabledDeviceEntry 4 } civrEnabledDeviceCapability OBJECT-TYPE SYNTAX BITS { version1 (0) } MAX-ACCESS read-only STATUS current DESCRIPTION "The switch WWN of this device." ::= { civrEnabledDeviceEntry 5 } -- -- objects that are sent with notifications -- civrZoneMemberFabricId OBJECT-TYPE SYNTAX FcAddressId MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The fabric address of the IV zone member which is not able to participate in inter-VSAN communication because of conflicting domainIDs." ::= { cimIvrStats 3 } civDomainIdConflictVsan OBJECT-TYPE SYNTAX VsanIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The VSAN in which the domainID conflict occurred." ::= { cimIvrStats 4 } civrZoneSetActDeactPartialSucss OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates if the IV zoneset activation/deactivation was partially success." ::= { cimIvrStats 5 } civrAfidMisConfigVsan OBJECT-TYPE SYNTAX VsanIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The VSAN in which the AFID mis-configuration occurred." ::= { cimIvrStats 6 } civrAfidMisConfigLocalAfid OBJECT-TYPE SYNTAX CIvrAutonomousFabricId MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The local AFID value in which the AFID mis-configuration occurred." ::= { cimIvrStats 7 } civrAfidMisConfigRemoteAfid OBJECT-TYPE SYNTAX CIvrAutonomousFabricId MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The remote AFID value in which the AFID mis-configuration occurred." ::= { cimIvrStats 8 } civrAfidMisConfigLocalSWwn OBJECT-TYPE SYNTAX FcNameId MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The local switch WWN in which the AFID mis-configuration occurred." ::= { cimIvrStats 9 } civrAfidMisConfigRemoteSWwn OBJECT-TYPE SYNTAX FcNameId MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The remote switch WWN in which the AFID mis-configuration occurred." ::= { cimIvrStats 10 } civrTopologyMisConfigReason OBJECT-TYPE SYNTAX INTEGER { unknown(1), afidMismatch(2)} MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The reason for a topology mis-configuration." ::= { cimIvrStats 11 } -- Notifications civrZoneActivationDoneNotify NOTIFICATION-TYPE OBJECTS { civrZoneSetName, civrZoneSetActvatDeactvatResult, civrZoneSetActDeactPartialSucss} STATUS current DESCRIPTION "This notification is generated on completion of an IV zoneset activation. civrZoneSetActDeactPartialSucss is valid only if the activation was successful." ::= { ciscoIvrMIBNotifications 1 } civrZoneDeactivationDoneNotify NOTIFICATION-TYPE OBJECTS { civrZoneSetName, civrZoneSetActvatDeactvatResult, civrZoneSetActDeactPartialSucss} STATUS current DESCRIPTION "This notification is generated on completion of an IV zoneset deactivation. civrZoneSetActDeactPartialSucss is valid only if the deactivation was successful." ::= { ciscoIvrMIBNotifications 2 } civrDomainConflictNotify NOTIFICATION-TYPE OBJECTS {civrZoneEnforcedZoneMemberID, civrZoneEnforcedZoneMemberVsan, civrZoneMemberFabricId, civDomainIdConflictVsan } STATUS current DESCRIPTION "This notification is sent when domainID conflict occurs in a VSAN. The domainIDs in all the VSANs (dmDatabaseTable in CISCO-DM-MIB) which are configured to be carrying inter-VSAN trafic (civrTopologyConfigTable) must be unique. If not, there could be domainID conflicts." ::= { ciscoIvrMIBNotifications 3 } civrAfidConfigNotify NOTIFICATION-TYPE OBJECTS {civrAfidMisConfigLocalAfid, civrAfidMisConfigRemoteAfid, civrAfidMisConfigLocalSWwn, civrAfidMisConfigRemoteSWwn, civrAfidMisConfigVsan, civrTopologyMisConfigReason } STATUS current DESCRIPTION "This notification is sent when an IVR AFID mis-configuration occurs." ::= { ciscoIvrMIBNotifications 4 } -- Conformance civrZoneServerMIBCompliances OBJECT IDENTIFIER ::= { ciscoIvrMIBConformance 1 } civrZoneServerMIBGroups OBJECT IDENTIFIER ::= { ciscoIvrMIBConformance 2 } civrZoneServerMIBCompliance MODULE-COMPLIANCE STATUS deprecated -- superceeded by -- civrZoneServerMIBComplianceRev1 DESCRIPTION "The compliance statement for entities which implement the Zone Server." MODULE MANDATORY-GROUPS {civrZoneConfigurationGroup, civrTopologyGroup, civrStatsGroup, civrNotificationGroup} OBJECT civrZoneSetRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} MIN-ACCESS read-only DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT civrZoneRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} MIN-ACCESS read-only DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT civrZoneMemberRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} MIN-ACCESS read-only DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT civrTopologyConfigRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} MIN-ACCESS read-only DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT civrZoneMemberAFId SYNTAX CIvrAutonomousFabricId (1) DESCRIPTION "Autonomous Fabric Id of 1 need to be supported." -- OBJECT civrTopologyConfigAutoFabricId -- SYNTAX CIvrAutonomousFabricId (1) -- DESCRIPTION -- "Autonomous Fabric Id of 1 need to be supported." ::= { civrZoneServerMIBCompliances 1 } civrZoneServerMIBComplianceRev1 MODULE-COMPLIANCE STATUS deprecated -- superceeded by -- civrZoneServerMIBComplianceRev2 DESCRIPTION "The compliance statement for entities which implement the Zone Server." MODULE MANDATORY-GROUPS {civrZoneConfigurationGroup, civrTopologyGroup, civrStatsGroup, civrNotificationGroup, civrVirtualDomainsGroup} OBJECT civrZoneSetRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} MIN-ACCESS read-only DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT civrZoneRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} MIN-ACCESS read-only DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT civrZoneMemberRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} MIN-ACCESS read-only DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT civrTopologyConfigRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} MIN-ACCESS read-only DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT civrZoneMemberAFId SYNTAX CIvrAutonomousFabricId (1) DESCRIPTION "Autonomous Fabric Id of 1 need to be supported." -- OBJECT civrTopologyConfigAutoFabricId -- SYNTAX CIvrAutonomousFabricId (1) -- DESCRIPTION -- "Autonomous Fabric Id of 1 need to be supported." ::= { civrZoneServerMIBCompliances 2 } civrZoneServerMIBComplianceRev2 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement the Zone Server." MODULE MANDATORY-GROUPS {civrZoneConfigurationGroup, civrTopologyGroup, civrStatsGroup, civrNotificationGroup, civrVirtualDomainsGroup, civrGenericGroup, civrTopologyGroupRev2, civrZoneConfigurationGroupRev2, civrNotificationGroupRev2} OBJECT civrZoneSetRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} MIN-ACCESS read-only DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT civrZoneRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} MIN-ACCESS read-only DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT civrZoneMemberRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} MIN-ACCESS read-only DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT civrTopologyConfigRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} MIN-ACCESS read-only DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT civrTopologyAfidConfRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} MIN-ACCESS read-only DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT civrTopologyDefaultAfidStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} MIN-ACCESS read-only DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT civrTopologyIvrSrvGrpRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6)} MIN-ACCESS read-only DESCRIPTION "Only three values 'createAndGo', 'destroy' and 'active' out of the six enumerated values need to be supported." OBJECT civrZoneMemberAFId SYNTAX CIvrAutonomousFabricId (1) DESCRIPTION "Autonomous Fabric Id of 1 need to be supported." -- OBJECT civrTopologyConfigAutoFabricId -- SYNTAX CIvrAutonomousFabricId (1) -- DESCRIPTION -- "Autonomous Fabric Id of 1 need to be supported." ::= { civrZoneServerMIBCompliances 3 } -- Units of Conformance civrZoneConfigurationGroup OBJECT-GROUP OBJECTS {civrZoneSetNumber, civrZoneSetName, civrZoneSetZoneList, civrZoneSetLastChange, civrZoneSetChecksum, civrZoneSetRowStatus, civrZoneSetActivate, civrZoneSetActvatDeactvatResult, civrZoneSetDeActivate, civrZoneNumber, civrZoneName, civrZoneMemberList, civrZoneLastChange, civrZoneRowStatus, civrZoneMemberNumber, civrZoneMemberType, civrZoneMemberID, civrZoneMemberAFId, civrZoneMemberVsan, civrZonesetDbChecksum, civrActiveZonesetChecksum, civrZoneMemberRowStatus, civrZoneEnforcedZoneSetName, civrZoneEnforcedZoneSetZoneList, civrZoneEnforcedZoneSetActvtTime, civrZoneEnforcedZoneNumber, civrZoneEnforcedZoneName, civrZoneEnforcedZoneMemberList, civrZoneEnforcedZoneMemberNumber, civrZoneEnforcedZoneMemberType, civrZoneEnforcedZoneMemberID, civrZoneEnforcedZoneMemberAFId, civrZoneEnforcedZoneMemberVsan, civrZoneCopyZoneSetEnforcdToFull, civrZoneClearFullZoneDb, civrZonesetActivateForce } STATUS current DESCRIPTION "A collection of objects for displaying and configuring IvrZone Membership." ::= { civrZoneServerMIBGroups 1 } civrTopologyGroup OBJECT-GROUP OBJECTS { civrTopologyConfigSwitchVsan2k, civrTopologyConfigSwitchVsan4k, civrTopologyConfigRowStatus, civrTopologyActiveSwitchVsan2k, civrTopologyActiveSwitchVsan4k, civrTopologyConfiguredChecksum, civrTopologyActiveChecksum, civrTopologyActivate, civrTopologyActivateTime, civrTopologyCopyActiveToConfig, civrTopologyClearConfigured, civrTopologyActive } STATUS current DESCRIPTION "A collection of objects for IVR topology." ::= { civrZoneServerMIBGroups 2 } civrStatsGroup OBJECT-GROUP OBJECTS { civrZoneSetStatus, civrEnabledDeviceSwitchWwn, civrEnabledDeviceCapability, civDomainIdConflictVsan, civrZoneMemberFabricId, civrZoneSetActDeactPartialSucss } STATUS current DESCRIPTION "A collection of objects for IVR status/statistics." ::= { civrZoneServerMIBGroups 3 } civrNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS {civrZoneActivationDoneNotify, civrZoneDeactivationDoneNotify, civrDomainConflictNotify} STATUS current DESCRIPTION "A collection of notification(s) for monitoring IVR related events." ::= { civrZoneServerMIBGroups 4 } civrVirtualDomainsGroup OBJECT-GROUP OBJECTS { civrAddIvrVirtualDomainsVsans2k, civrAddIvrVirtualDomainsVsans4k } STATUS current DESCRIPTION "A collection of objects for IVR status/statistics." ::= { civrZoneServerMIBGroups 5 } civrGenericGroup OBJECT-GROUP OBJECTS { civrFcidNatMode, civrVsanTopologyAutoDisc } STATUS current DESCRIPTION "A collection of objects for IVR generic configurations." ::= { civrZoneServerMIBGroups 6 } civrTopologyGroupRev2 OBJECT-GROUP OBJECTS { civrTopologyAfidConfSwitchVsan2k, civrTopologyAfidConfSwitchVsan4k, civrTopologyAfidConfRowStatus, civrTopologyDefaultAfidId, civrTopologyDefaultAfidStatus, civrTopologyIvrSrvGrpVsan2k, civrTopologyIvrSrvGrpVsan4k, civrTopologyIvrSrvGrpRowStatus, civrTopologyAfidConfigChecksum, civrTopologyDefaultAfidChecksum, civrTopologyClearAfidConfig, civrAfidMisConfigVsan, civrAfidMisConfigLocalAfid, civrAfidMisConfigRemoteAfid, civrAfidMisConfigLocalSWwn, civrAfidMisConfigRemoteSWwn, civrTopologyMisConfigReason } STATUS current DESCRIPTION "A collection of objects for IVR topology." ::= { civrZoneServerMIBGroups 7 } civrZoneConfigurationGroupRev2 OBJECT-GROUP OBJECTS { civrZoneReadOnly, civrZoneQosPriority, civrZoneEnforcedZoneReadOnly, civrZoneEnforcedZoneQosPriority, civrZoneMemberLunID, civrZoneEnforcedZoneMemberLunID, civrZoneSetTableNextIndex, civrZoneTableNextIndex } STATUS current DESCRIPTION "A collection of objects to support SCSI read only, Qos and Lun zoning in IVR Zone Membership configurations." ::= { civrZoneServerMIBGroups 8 } civrNotificationGroupRev2 NOTIFICATION-GROUP NOTIFICATIONS {civrAfidConfigNotify} STATUS current DESCRIPTION "A collection of notification(s) for monitoring IVR related events." ::= { civrZoneServerMIBGroups 9 } END