-- ********************************************************************* -- CISCO-ISCSI-MIB.my: iSCSI (SCSI over TCP) Mib -- -- October 2002, Vinay Gaonkar -- -- Copyright (c) 2002 by cisco Systems, Inc. -- All rights reserved. -- -- ********************************************************************* -- This MIB module is based on the Internet Draft -- . In terms of object syntax -- and semantics, the content of this Cisco MIB is the same as -- the corresponding Internet Draft revision. This Cisco MIB was -- created due to the "subject to change" nature of Internet Drafts. -- This Cisco MIB may later be deprecated, and the stable RFC, which -- may replace the Internet Draft, may be implemented in its place. CISCO-ISCSI-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, OBJECT-IDENTITY, NOTIFICATION-TYPE, Unsigned32, Counter32, Counter64, Gauge32 FROM SNMPv2-SMI TEXTUAL-CONVENTION, TruthValue, RowPointer, TimeStamp, RowStatus, AutonomousType FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF SnmpAdminString FROM SNMP-FRAMEWORK-MIB -- RFC 2571 InetAddressType, InetAddress FROM INET-ADDRESS-MIB -- RFC 3291 ciscoExperiment FROM CISCO-SMI ; ciscoIscsiModule MODULE-IDENTITY LAST-UPDATED "200210050000Z" ORGANIZATION "IETF IPS Working Group" CONTACT-INFO " Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553 -NETS E-mail: cs-san@cisco.com" DESCRIPTION "The iSCSI Protocol MIB module." REVISION "200210050000Z" DESCRIPTION "Initial revision published of this MIB module." ::= { ciscoExperiment 94 } cIscsiObjects OBJECT IDENTIFIER ::= { ciscoIscsiModule 1 } cIscsiNotifications OBJECT IDENTIFIER ::= { ciscoIscsiModule 2 } cIscsiConformance OBJECT IDENTIFIER ::= { ciscoIscsiModule 3 } -- Textual Conventions CIscsiTransportProtocols ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "This data type is used to define the transport protocols that will carry iSCSI PDUs." REFERENCE "RFC791, RFC1700 The presently known, officially delegated numbers can be found at: http://www.iana.org/assignments/protocol-numbers" SYNTAX Unsigned32 (0..255) CIscsiDigestMethod ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This data type represents the methods possible for digest negotiation. none - a placeholder for a secondary digest method that means only the primary method can be used. other - a digest method other than those defined below; noDigest - does not support digests (will operate without a digest (NOTE: implementations MUST support digests to be compliant with the iSCSI RFC); CRC32c - require a CRC32C digest." SYNTAX INTEGER { none(1), other(2), noDigest(3), crc32c(4) } cIscsiDescriptors OBJECT IDENTIFIER ::= { cIscsiObjects 1 } cIscsiHeaderIntegrityTypes OBJECT IDENTIFIER ::= { cIscsiDescriptors 1 } cIscsiHdrIntegrityNone OBJECT-IDENTITY STATUS current DESCRIPTION "The authoritative identifier when no integrity scheme (for either the header or data) is being used." REFERENCE "iSCSI Protocol Specification." ::= { cIscsiHeaderIntegrityTypes 1 } cIscsiHdrIntegrityCrc32c OBJECT-IDENTITY STATUS current DESCRIPTION "The authoritative identifier when the integrity scheme (for either the header or data) is CRC-32c." REFERENCE "iSCSI Protocol Specification." ::= { cIscsiHeaderIntegrityTypes 2 } cIscsiDataIntegrityTypes OBJECT IDENTIFIER ::= { cIscsiDescriptors 2 } cIscsiDataIntegrityNone OBJECT-IDENTITY STATUS current DESCRIPTION "The authoritative identifier when no integrity scheme (for either the header or data) is being used." REFERENCE "iSCSI Protocol Specification." ::= { cIscsiDataIntegrityTypes 1 } cIscsiDataIntegrityCrc32c OBJECT-IDENTITY STATUS current DESCRIPTION "The authoritative identifier when the integrity scheme (for either the header or data) is CRC-32c." REFERENCE "iSCSI Protocol Specification." ::= { cIscsiDataIntegrityTypes 2 } cIscsiInstance OBJECT IDENTIFIER ::= { cIscsiObjects 2 } -- Instance Attributes Table cIscsiInstanceAttributesTable OBJECT-TYPE SYNTAX SEQUENCE OF CIscsiInstanceAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of iSCSI instances present on the system." ::= { cIscsiInstance 1 } cIscsiInstanceAttributesEntry OBJECT-TYPE SYNTAX CIscsiInstanceAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing management information applicable to a particular iSCSI instance." INDEX { cIscsiInstIndex } ::= { cIscsiInstanceAttributesTable 1 } CIscsiInstanceAttributesEntry ::= SEQUENCE { cIscsiInstIndex Unsigned32, cIscsiInstDescr SnmpAdminString, cIscsiInstVersionMin Unsigned32, cIscsiInstVersionMax Unsigned32, cIscsiInstVendorID SnmpAdminString, cIscsiInstVendorVersion SnmpAdminString, cIscsiInstPortalNumber Unsigned32, cIscsiInstNodeNumber Unsigned32, cIscsiInstSessionNumber Unsigned32, cIscsiInstSsnFailures Counter32, cIscsiInstLastSsnFailureType AutonomousType, cIscsiInstLastSsnRmtNodeName SnmpAdminString } cIscsiInstIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer used to uniquely identify a particular ISCSI instance." ::= { cIscsiInstanceAttributesEntry 1 } cIscsiInstDescr OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "An octet string, determined by the implementation to describe the iSCSI instance. When only a single instance is present, this object may be set to the zero-length string; with multiple iSCSI instances, it may be used in an implementation-dependent manner to describe the purpose of the respective instance." ::= { cIscsiInstanceAttributesEntry 2 } cIscsiInstVersionMin OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum version number of the iSCSI specification supported by this instance." ::= { cIscsiInstanceAttributesEntry 3 } cIscsiInstVersionMax OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum version number of the iSCSI specification supported by this instance." ::= { cIscsiInstanceAttributesEntry 4 } cIscsiInstVendorID OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "An octet string describing the manufacturer of the implementation of this instance." ::= { cIscsiInstanceAttributesEntry 5 } cIscsiInstVendorVersion OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "An octet string set by the manufacturer describing the version of the implementation of this instance. The format of this string is determined solely by the manufacturer, and is for informational purposes only. It is unrelated to the iSCSI specification version numbers." ::= { cIscsiInstanceAttributesEntry 6 } cIscsiInstPortalNumber OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) UNITS "transport endpoints" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of rows in the cIscsiPortalAttributesTable which are currently associated with this iSCSI instance." ::= { cIscsiInstanceAttributesEntry 7 } cIscsiInstNodeNumber OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) UNITS "Internet Network Addresses" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of rows in the cIscsiNodeAttributesTable which are currently associated with this iSCSI instance." ::= { cIscsiInstanceAttributesEntry 8 } cIscsiInstSessionNumber OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) UNITS "sessions" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of rows in the cIscsiSessionAttributesTable which are currently associated with this iSCSI instance." ::= { cIscsiInstanceAttributesEntry 9 } cIscsiInstSsnFailures OBJECT-TYPE SYNTAX Counter32 UNITS "sessions" MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of times a session belonging to this instance has been failed." ::= { cIscsiInstanceAttributesEntry 10 } cIscsiInstLastSsnFailureType OBJECT-TYPE SYNTAX AutonomousType MAX-ACCESS read-only STATUS current DESCRIPTION "The counter object in the cIscsiInstSsnErrorStatsTable that was incremented when the last session failure occurred. If the reason for failure is not found in the cIscsiInstSsnErrorStatsTable, the value { 0.0 } is used instead." ::= { cIscsiInstanceAttributesEntry 11 } cIscsiInstLastSsnRmtNodeName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "An octet string describing the name of the remote node from the failed session." ::= { cIscsiInstanceAttributesEntry 12 } -- Instance Session Failure Stats Table cIscsiInstanceSsnErrorStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF CIscsiInstanceSsnErrorStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of error types that will cause a session failure." ::= { cIscsiInstance 2 } cIscsiInstanceSsnErrorStatsEntry OBJECT-TYPE SYNTAX CIscsiInstanceSsnErrorStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing management information applicable to a particular iSCSI instance." AUGMENTS { cIscsiInstanceAttributesEntry } ::= { cIscsiInstanceSsnErrorStatsTable 1 } CIscsiInstanceSsnErrorStatsEntry ::= SEQUENCE { cIscsiInstSsnDigestErrors Counter32, cIscsiInstSsnCxnTimeoutErrors Counter32, cIscsiInstSsnFormatErrors Counter32 } cIscsiInstSsnDigestErrors OBJECT-TYPE SYNTAX Counter32 UNITS "sessions" MAX-ACCESS read-only STATUS current DESCRIPTION "The count of sessions which were failed due to receipt of a PDU containing header or data digest errors." ::= { cIscsiInstanceSsnErrorStatsEntry 1 } cIscsiInstSsnCxnTimeoutErrors OBJECT-TYPE SYNTAX Counter32 UNITS "sessions" MAX-ACCESS read-only STATUS current DESCRIPTION "The count of sessions which were failed due to a sequence exceeding a time limit." ::= { cIscsiInstanceSsnErrorStatsEntry 2 } cIscsiInstSsnFormatErrors OBJECT-TYPE SYNTAX Counter32 UNITS "sessions" MAX-ACCESS read-only STATUS current DESCRIPTION "The count of sessions which were failed due to receipt of a PDU which contained a format error." ::= { cIscsiInstanceSsnErrorStatsEntry 3 } -- cIscsiPortal OBJECT IDENTIFIER ::= { cIscsiObjects 3 } -- Portal Attributes Table cIscsiPortalAttributesTable OBJECT-TYPE SYNTAX SEQUENCE OF CIscsiPortalAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of transport endpoints (using TCP or another transport protocol) used by this iSCSI instance. An iSCSI instance may use a portal to listen for incoming connections to its targets, to initiate connections to other targets, or both." ::= { cIscsiPortal 1 } cIscsiPortalAttributesEntry OBJECT-TYPE SYNTAX CIscsiPortalAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing management information applicable to a particular portal instance." INDEX { cIscsiInstIndex, cIscsiPortalIndex } ::= { cIscsiPortalAttributesTable 1 } CIscsiPortalAttributesEntry ::= SEQUENCE { cIscsiPortalIndex Unsigned32, cIscsiPortalRowStatus RowStatus, cIscsiPortalRoles BITS, cIscsiPortalAddrType InetAddressType, cIscsiPortalAddr InetAddress, cIscsiPortalProtocol CIscsiTransportProtocols, cIscsiPortalMaxRecvDataSegLength Unsigned32, cIscsiPortalPrimaryHdrDigest CIscsiDigestMethod, cIscsiPortalPrimaryDataDigest CIscsiDigestMethod, cIscsiPortalSecondaryHdrDigest CIscsiDigestMethod, cIscsiPortalSecondaryDataDigest CIscsiDigestMethod, cIscsiPortalRecvMarker TruthValue } cIscsiPortalIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer used to uniquely identify a particular transport endpoint within this iSCSI instance." ::= { cIscsiPortalAttributesEntry 1 } cIscsiPortalRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of the row." ::= { cIscsiPortalAttributesEntry 2 } cIscsiPortalRoles OBJECT-TYPE SYNTAX BITS { targetTypePortal(0), initiatorTypePortal(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "A portal can operate in one or both of two roles: as a target portal and/or an initiator portal. When a new cIscsiPortalAttributesEntry is to be created, the agent should use this object as a hint for the creation of a new cIscsiTgtPortalAttributesEntry and/or cIscsiIntrPortalAttributesEntry." ::= { cIscsiPortalAttributesEntry 3 } cIscsiPortalAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "The type of Internet Network Address in the cIscsiPortalAddr." ::= { cIscsiPortalAttributesEntry 4 } cIscsiPortalAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The portal's Internet Network Address." ::= { cIscsiPortalAttributesEntry 5 } cIscsiPortalProtocol OBJECT-TYPE SYNTAX CIscsiTransportProtocols MAX-ACCESS read-create STATUS current DESCRIPTION "The portal's transport protocol." DEFVAL { 6 } -- TCP ::= { cIscsiPortalAttributesEntry 6 } cIscsiPortalMaxRecvDataSegLength OBJECT-TYPE SYNTAX Unsigned32 (512..16777215) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum PDU length this portal can receive. This may be constrained by hardware characteristics and individual implementations may chose not to allow this object to be changed." DEFVAL { 8192 } ::= { cIscsiPortalAttributesEntry 7 } cIscsiPortalPrimaryHdrDigest OBJECT-TYPE SYNTAX CIscsiDigestMethod MAX-ACCESS read-create STATUS current DESCRIPTION "The preferred header digest for this portal." DEFVAL { noDigest } ::= { cIscsiPortalAttributesEntry 8 } cIscsiPortalPrimaryDataDigest OBJECT-TYPE SYNTAX CIscsiDigestMethod MAX-ACCESS read-create STATUS current DESCRIPTION "The preferred data digest method for this portal." DEFVAL { noDigest } ::= { cIscsiPortalAttributesEntry 9 } cIscsiPortalSecondaryHdrDigest OBJECT-TYPE SYNTAX CIscsiDigestMethod MAX-ACCESS read-create STATUS current DESCRIPTION "An alternate header digest preference for this portal." DEFVAL { none } ::= { cIscsiPortalAttributesEntry 10 } cIscsiPortalSecondaryDataDigest OBJECT-TYPE SYNTAX CIscsiDigestMethod MAX-ACCESS read-create STATUS current DESCRIPTION "An alternate data digest preference for this portal." DEFVAL { none } ::= { cIscsiPortalAttributesEntry 11 } cIscsiPortalRecvMarker OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates whether or not this portal will request markers in it's incoming data stream." ::= { cIscsiPortalAttributesEntry 12 } cIscsiTargetPortal OBJECT IDENTIFIER ::= { cIscsiObjects 4 } -- Target Portal Attributes Table cIscsiTgtPortalAttributesTable OBJECT-TYPE SYNTAX SEQUENCE OF CIscsiTgtPortalAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of transport endpoints (using TCP or another transport protocol) on which this iSCSI instance listens for incoming connections to its targets." ::= { cIscsiTargetPortal 1 } cIscsiTgtPortalAttributesEntry OBJECT-TYPE SYNTAX CIscsiTgtPortalAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing management information applicable to a particular portal instance that is used to listen for incoming connections to local targets. This row is populated for each cIscsiPortalAttributesEntry row that may be used as a target portal." INDEX { cIscsiInstIndex, cIscsiPortalIndex } ::= { cIscsiTgtPortalAttributesTable 1 } CIscsiTgtPortalAttributesEntry ::= SEQUENCE { cIscsiTgtPortalPort Unsigned32, cIscsiTgtPortalTag Unsigned32 } cIscsiTgtPortalPort OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The portal's transport protocol port number on which the portal listens for incoming iSCSI connections when the portal is used as a target portal." ::= { cIscsiTgtPortalAttributesEntry 1 } cIscsiTgtPortalTag OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The portal's aggregation tag when portal is used as a target portal. Multiple-connection sessions may be aggregated over portals sharing an identical aggregation tag." ::= { cIscsiTgtPortalAttributesEntry 2 } cIscsiInitiatorPortal OBJECT IDENTIFIER ::= { cIscsiObjects 5 } -- Initiator Portal Attributes Table cIscsiIntrPortalAttributesTable OBJECT-TYPE SYNTAX SEQUENCE OF CIscsiIntrPortalAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of Internet Network Addresses (using TCP or another transport protocol) from which this iSCSI instance may initiate connections to other targets." ::= { cIscsiInitiatorPortal 1 } cIscsiIntrPortalAttributesEntry OBJECT-TYPE SYNTAX CIscsiIntrPortalAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing management information applicable to a particular portal instance that is used to initiate connections to iSCSI targets. This row is populated for each cIscsiPortalAttributesEntry row that may be used as an initiator portal." INDEX { cIscsiInstIndex, cIscsiPortalIndex } ::= { cIscsiIntrPortalAttributesTable 1 } CIscsiIntrPortalAttributesEntry ::= SEQUENCE { cIscsiIntrPortalTag Unsigned32 } cIscsiIntrPortalTag OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The portal's aggregation tag when the portal is used as an initiator portal. Multiple-connection sessions may be aggregated over portals sharing an identical aggregation tag." ::= { cIscsiIntrPortalAttributesEntry 1 } cIscsiNode OBJECT IDENTIFIER ::= { cIscsiObjects 6 } -- Node Attributes Table cIscsiNodeAttributesTable OBJECT-TYPE SYNTAX SEQUENCE OF CIscsiNodeAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of iSCSI nodes belonging to each iSCSI instance present on the local system. An iSCSI node can act as an initiator, a target, or both." ::= { cIscsiNode 1 } cIscsiNodeAttributesEntry OBJECT-TYPE SYNTAX CIscsiNodeAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing management information applicable to a particular iSCSI node." INDEX { cIscsiInstIndex, cIscsiNodeIndex } ::= { cIscsiNodeAttributesTable 1 } CIscsiNodeAttributesEntry ::= SEQUENCE { cIscsiNodeIndex Unsigned32, cIscsiNodeName SnmpAdminString, cIscsiNodeAlias SnmpAdminString, cIscsiNodeRoles BITS, cIscsiNodeTransportType RowPointer, cIscsiNodeInitialR2T TruthValue, cIscsiNodeBidiInitialR2T TruthValue, cIscsiNodeImmediateData TruthValue, cIscsiNodeMaxOutstandingR2T Unsigned32, cIscsiNodeFirstBurstSize Unsigned32, cIscsiNodeMaxBurstSize Unsigned32, cIscsiNodeMaxConnections Unsigned32, cIscsiNodeDataSequenceInOrder TruthValue, cIscsiNodeDataPduInOrder TruthValue, cIscsiNodeDefaultTime2Wait Unsigned32, cIscsiNodeDefaultTime2Retain Unsigned32, cIscsiNodeErrorRecoveryLevel Unsigned32 } cIscsiNodeIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer used to uniquely identify a particular node within an iSCSI instance present on the local system." ::= { cIscsiNodeAttributesEntry 1 } cIscsiNodeName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "A character string that is a globally unique identifier for this iSCSI node. The node name is independent of the location of the node, and can be resolved into a set of addresses through various discovery services." ::= { cIscsiNodeAttributesEntry 2 } cIscsiNodeAlias OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "A character string that is a human-readable name or description of the iSCSI node. If configured, this alias may be communicated to the initiator or target node at the remote end of the connection during a Login Request or Response message. This string is not used as an identifier, but can be displayed by the system's user interface in a list of initiators and/or targets to which it is connected. If no alias is configured, this object is a zero-length string." ::= { cIscsiNodeAttributesEntry 3 } cIscsiNodeRoles OBJECT-TYPE SYNTAX BITS { targetTypeNode(0), initiatorTypeNode(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "A node can operate as in one or both of two roles: a target role and/or an initiator role." ::= { cIscsiNodeAttributesEntry 4 } cIscsiNodeTransportType OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-only STATUS current DESCRIPTION "A pointer to the corresponding scsiTrnspt object in the CISCO-SCSI-MIB (which in turn points to this iSCSI node) allowing management stations to locate the SCSI-level Device that is represented by this cIscsiNode." REFERENCE "CISCO-SCSI-MIB" ::= { cIscsiNodeAttributesEntry 5 } cIscsiNodeInitialR2T OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates InitialR2T preference for this node - True = YES, False = will try to negotiate NO, will accept YES " DEFVAL { true } ::= { cIscsiNodeAttributesEntry 6 } cIscsiNodeBidiInitialR2T OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates BidiInitialR2T preference for this node- True = YES, False = will try to negotiate NO, will accept YES " DEFVAL { true } ::= { cIscsiNodeAttributesEntry 7 } cIscsiNodeImmediateData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates ImmediateData preference for this node True = YES (but will accept NO), False = NO " DEFVAL { true } ::= { cIscsiNodeAttributesEntry 8 } cIscsiNodeMaxOutstandingR2T OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum number of outstanding R2Ts allowed per task." DEFVAL { 1 } ::= { cIscsiNodeAttributesEntry 9 } cIscsiNodeFirstBurstSize OBJECT-TYPE SYNTAX Unsigned32 (512..16777215) UNITS "bytes" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum length (bytes) supported for unsolicited data to/from this node." DEFVAL { 65536 } ::= { cIscsiNodeAttributesEntry 10 } cIscsiNodeMaxBurstSize OBJECT-TYPE SYNTAX Unsigned32 (512..16777215) UNITS "bytes" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of bytes which can be sent within a single sequence of Data-In or Data-Out PDUs." DEFVAL { 262144 } ::= { cIscsiNodeAttributesEntry 11 } cIscsiNodeMaxConnections OBJECT-TYPE SYNTAX Unsigned32 (1..65535) UNITS "connections" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of connections allowed in each session to and/or from this node." DEFVAL { 1 } ::= { cIscsiNodeAttributesEntry 12 } cIscsiNodeDataSequenceInOrder OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The DataSequenceInOrder preference of this node. False (=No) indicates that iSCSI data PDU sequences may be transferred in any order. True (=Yes) indicates that data PDU sequences must be transferred using continuously increasing offsets, except during error recovery." DEFVAL { true } ::= { cIscsiNodeAttributesEntry 13 } cIscsiNodeDataPduInOrder OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The DataPDUInOrder preference of this node. False (=No) indicates that iSCSI data PDUs within sequences may be in any order. True (=Yes) indicates that data PDUs within sequences must be at continuously increasing addresses, with no gaps or overlay between PDUs." DEFVAL { true } ::= { cIscsiNodeAttributesEntry 14 } cIscsiNodeDefaultTime2Wait OBJECT-TYPE SYNTAX Unsigned32 (0..3600) MAX-ACCESS read-write STATUS current DESCRIPTION "The DefaultTime2Wait preference of this node. This is the minimum time, in seconds, to wait before attempting an explicit/implicit logout or active task reassignment after an unexpected connection termination or a connection reset." DEFVAL { 2 } ::= { cIscsiNodeAttributesEntry 15 } cIscsiNodeDefaultTime2Retain OBJECT-TYPE SYNTAX Unsigned32 (0..3600) MAX-ACCESS read-write STATUS current DESCRIPTION "The DefaultTime2Retain preference of this node. This is the maximum time, in seconds after an initial wait (Time2Wait), before which an active task reassignment is still possible after an unexpected connection termination or a connection reset." DEFVAL { 20 } ::= { cIscsiNodeAttributesEntry 16 } cIscsiNodeErrorRecoveryLevel OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "The ErrorRecoveryLevel preference of this node. Currently, only 0-2 are valid. This object is designed to accommodate future error recover levels. Higher error recovery levels imply support in addition to support for the lower error level functions. In otherwords, error level 2 implies support for levels 0-1, since those functions are subsets of error level 2." DEFVAL { 0 } ::= { cIscsiNodeAttributesEntry 17 } cIscsiTarget OBJECT IDENTIFIER ::= { cIscsiObjects 7 } -- Target Attributes Table cIscsiTargetAttributesTable OBJECT-TYPE SYNTAX SEQUENCE OF CIscsiTargetAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing management information applicable to a particular node that can take on a target role." ::= { cIscsiTarget 1 } cIscsiTargetAttributesEntry OBJECT-TYPE SYNTAX CIscsiTargetAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing management information applicable to a particular target." INDEX { cIscsiInstIndex, cIscsiNodeIndex } ::= { cIscsiTargetAttributesTable 1 } CIscsiTargetAttributesEntry ::= SEQUENCE { cIscsiTgtLoginFailures Counter32, cIscsiTgtLastFailureTime TimeStamp, cIscsiTgtLastFailureType AutonomousType, cIscsiTgtLastIntrFailureName SnmpAdminString, cIscsiTgtLastIntrFailureAddrType InetAddressType, cIscsiTgtLastIntrFailureAddr InetAddress } cIscsiTgtLoginFailures OBJECT-TYPE SYNTAX Counter32 UNITS "failed login attempts" MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of times a login attempt to this local target has failed." ::= { cIscsiTargetAttributesEntry 1 } cIscsiTgtLastFailureTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The timestamp of the most recent failure of a login attempt to this target. A value of zero indicates that no such failures have occurred." ::= { cIscsiTargetAttributesEntry 2 } cIscsiTgtLastFailureType OBJECT-TYPE SYNTAX AutonomousType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the most recent failure of a login attempt to this target, represented as the OID of the counter object in cIscsiTargetLoginStatsTable for which the relevant instance was incremented. A value of 0.0 indicates a type which is not represented by any of the counters in cIscsiTargetLoginStatsTable." ::= { cIscsiTargetAttributesEntry 3 } cIscsiTgtLastIntrFailureName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "An octet string giving the name of the initiator that failed the last login attempt." ::= { cIscsiTargetAttributesEntry 4 } cIscsiTgtLastIntrFailureAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of Internet Network Address in cIscsiTgtLastIntrFailureAddr." ::= { cIscsiTargetAttributesEntry 5 } cIscsiTgtLastIntrFailureAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "An Internet Network Address giving the host address of the initiator that failed the last login attempt." ::= { cIscsiTargetAttributesEntry 6 } -- Target Login Stats Table cIscsiTargetLoginStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF CIscsiTargetLoginStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of counters which keep a record of the results of initiators' login attempts to this target." ::= { cIscsiTarget 2 } cIscsiTargetLoginStatsEntry OBJECT-TYPE SYNTAX CIscsiTargetLoginStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing counters for each result of a login attempt to this target." AUGMENTS { cIscsiTargetAttributesEntry } ::= { cIscsiTargetLoginStatsTable 1 } CIscsiTargetLoginStatsEntry ::= SEQUENCE { cIscsiTgtLoginAccepts Counter32, cIscsiTgtLoginOtherFails Counter32, cIscsiTgtLoginRedirects Counter32, cIscsiTgtLoginAuthorizeFails Counter32, cIscsiTgtLoginAuthenticateFails Counter32, cIscsiTgtLoginNegotiateFails Counter32 } cIscsiTgtLoginAccepts OBJECT-TYPE SYNTAX Counter32 UNITS "successful logins" MAX-ACCESS read-only STATUS current DESCRIPTION "The count of Login Response PDUs with status 0x0000, Accept Login, transmitted by this target." ::= { cIscsiTargetLoginStatsEntry 1 } cIscsiTgtLoginOtherFails OBJECT-TYPE SYNTAX Counter32 UNITS "failed logins" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Login Response PDUs which were transmitted by this target, and which were not counted by any other object in the row." ::= { cIscsiTargetLoginStatsEntry 2 } cIscsiTgtLoginRedirects OBJECT-TYPE SYNTAX Counter32 UNITS "failed logins" MAX-ACCESS read-only STATUS current DESCRIPTION "The count of Login Response PDUs with status class 0x01, Redirection, transmitted by this target." ::= { cIscsiTargetLoginStatsEntry 3 } cIscsiTgtLoginAuthorizeFails OBJECT-TYPE SYNTAX Counter32 UNITS "failed logins" MAX-ACCESS read-only STATUS current DESCRIPTION "The count of Login Response PDUs with status 0x0202, Forbidden Target, transmitted by this target. If this counter is incremented, an cIscsiTgtLoginFailure notification should be generated." ::= { cIscsiTargetLoginStatsEntry 4 } cIscsiTgtLoginAuthenticateFails OBJECT-TYPE SYNTAX Counter32 UNITS "failed logins" MAX-ACCESS read-only STATUS current DESCRIPTION "The count of Login Response PDUs with status 0x0201, Authentication Failed, transmitted by this target If this counter is incremented, an cIscsiTgtLoginFailure notification should be generated." ::= { cIscsiTargetLoginStatsEntry 5 } cIscsiTgtLoginNegotiateFails OBJECT-TYPE SYNTAX Counter32 UNITS "failed logins" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times a target has effectively refused a login because the parameter negotiation failed. [Ed. While this situation can occur, the exact mechanism is as yet undefined in the iSCSI Protocol Spec.] If this counter is incremented, an cIscsiTgtLoginFailure notification should be generated." ::= { cIscsiTargetLoginStatsEntry 6 } -- Target Logout Stats Table cIscsiTargetLogoutStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF CIscsiTargetLogoutStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "When a target receives a Logout command, it responds with a Logout Response that carries a status code. This table contains counters for both normal and abnormal logout requests received by this target." ::= { cIscsiTarget 3 } cIscsiTargetLogoutStatsEntry OBJECT-TYPE SYNTAX CIscsiTargetLogoutStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing counters of Logout Response PDUs that were received by this target." AUGMENTS { cIscsiTargetAttributesEntry } ::= { cIscsiTargetLogoutStatsTable 1 } CIscsiTargetLogoutStatsEntry ::= SEQUENCE { cIscsiTgtLogoutNormals Counter32, cIscsiTgtLogoutOthers Counter32 } cIscsiTgtLogoutNormals OBJECT-TYPE SYNTAX Counter32 UNITS "normal logouts" MAX-ACCESS read-only STATUS current DESCRIPTION "The count of Logout Command PDUs received by this target, with reason code 0 (closes the session)." ::= { cIscsiTargetLogoutStatsEntry 1 } cIscsiTgtLogoutOthers OBJECT-TYPE SYNTAX Counter32 UNITS "abnormal logouts" MAX-ACCESS read-only STATUS current DESCRIPTION "The count of Logout Command PDUs received by this target, with any status code other than 0." ::= { cIscsiTargetLogoutStatsEntry 2 } cIscsiTgtAuthorization OBJECT IDENTIFIER ::= { cIscsiObjects 8 } -- Target Authorization Attributes Table cIscsiTgtAuthAttributesTable OBJECT-TYPE SYNTAX SEQUENCE OF CIscsiTgtAuthAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of initiator identities that are authorized to access each target node within each iSCSI instance present on the local system." ::= { cIscsiTgtAuthorization 1 } cIscsiTgtAuthAttributesEntry OBJECT-TYPE SYNTAX CIscsiTgtAuthAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing management information applicable to a particular target node's authorized initiator identity." INDEX { cIscsiInstIndex, cIscsiNodeIndex, cIscsiTgtAuthIndex } ::= { cIscsiTgtAuthAttributesTable 1 } CIscsiTgtAuthAttributesEntry ::= SEQUENCE { cIscsiTgtAuthIndex Unsigned32, cIscsiTgtAuthRowStatus RowStatus, cIscsiTgtAuthIdentity RowPointer } cIscsiTgtAuthIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer used to uniquely identify a particular target's authorized initiator identity within an iSCSI instance present on the local system." ::= { cIscsiTgtAuthAttributesEntry 1 } cIscsiTgtAuthRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of the row." ::= { cIscsiTgtAuthAttributesEntry 2 } cIscsiTgtAuthIdentity OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-create STATUS current DESCRIPTION "A pointer to the corresponding IPS-AUTH MIB user entry that will be allowed to access this iSCSI target." REFERENCE "IPS-AUTH MIB" ::= { cIscsiTgtAuthAttributesEntry 3 } cIscsiInitiator OBJECT IDENTIFIER ::= { cIscsiObjects 9 } -- Initiator Attributes Table cIscsiInitiatorAttributesTable OBJECT-TYPE SYNTAX SEQUENCE OF CIscsiInitiatorAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of iSCSI nodes that can take on an initiator role, belonging to each iSCSI instance present on the local system." ::= { cIscsiInitiator 1 } cIscsiInitiatorAttributesEntry OBJECT-TYPE SYNTAX CIscsiInitiatorAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing management information applicable to a particular iSCSI node that has initiator capabilities." INDEX { cIscsiInstIndex, cIscsiNodeIndex } ::= { cIscsiInitiatorAttributesTable 1 } CIscsiInitiatorAttributesEntry ::= SEQUENCE { cIscsiIntrLoginFailures Counter32, cIscsiIntrLastFailureTime TimeStamp, cIscsiIntrLastFailureType AutonomousType, cIscsiIntrLastTgtFailureName SnmpAdminString, cIscsiIntrLastTgtFailureAddrType InetAddressType, cIscsiIntrLastTgtFailureAddr InetAddress } cIscsiIntrLoginFailures OBJECT-TYPE SYNTAX Counter32 UNITS "failed logins" MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of times a login attempt from this local initiator has failed." ::= { cIscsiInitiatorAttributesEntry 1 } cIscsiIntrLastFailureTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The timestamp of the most recent failure of a login attempt from this initiator. A value of zero indicates that no such failures have occurred." ::= { cIscsiInitiatorAttributesEntry 2 } cIscsiIntrLastFailureType OBJECT-TYPE SYNTAX AutonomousType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the most recent failure of a login attempt from this initiator, represented as the OID of the counter object in cIscsiInitiatorLoginStatsTable for which the relevant instance was incremented. A value of 0.0 indicates a type which is not represented by any of the counters in cIscsiInitiatorLoginStatsTable." ::= { cIscsiInitiatorAttributesEntry 3 } cIscsiIntrLastTgtFailureName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "An octet string giving the name of the target that failed the last login attempt." ::= { cIscsiInitiatorAttributesEntry 4 } cIscsiIntrLastTgtFailureAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of Internet Network Address in cIscsiIntrLastTgtFailureAddr." ::= { cIscsiInitiatorAttributesEntry 5 } cIscsiIntrLastTgtFailureAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "An Internet Network Address giving the host address of the target that failed the last login attempt." ::= { cIscsiInitiatorAttributesEntry 6 } -- Initiator Login Stats Table cIscsiInitiatorLoginStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF CIscsiInitiatorLoginStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of counters which keep track of the results of this initiator's login attempts." ::= { cIscsiInitiator 2 } cIscsiInitiatorLoginStatsEntry OBJECT-TYPE SYNTAX CIscsiInitiatorLoginStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing counters of each result of this initiator's login attempts." AUGMENTS { cIscsiInitiatorAttributesEntry } ::= { cIscsiInitiatorLoginStatsTable 1 } CIscsiInitiatorLoginStatsEntry ::= SEQUENCE { cIscsiIntrLoginAcceptRsps Counter32, cIscsiIntrLoginOtherFailRsps Counter32, cIscsiIntrLoginRedirectRsps Counter32, cIscsiIntrLoginAuthFailRsps Counter32, cIscsiIntrLoginAuthenticateFails Counter32, cIscsiIntrLoginNegotiateFails Counter32 } cIscsiIntrLoginAcceptRsps OBJECT-TYPE SYNTAX Counter32 UNITS "successful logins" MAX-ACCESS read-only STATUS current DESCRIPTION "The count of Login Response PDUs with status 0x0000, Accept Login, received by this initiator." ::= { cIscsiInitiatorLoginStatsEntry 1 } cIscsiIntrLoginOtherFailRsps OBJECT-TYPE SYNTAX Counter32 UNITS "failed logins" MAX-ACCESS read-only STATUS current DESCRIPTION "The count of Login Response PDUs received by this initiator with any status code not counted in the objects below." ::= { cIscsiInitiatorLoginStatsEntry 2 } cIscsiIntrLoginRedirectRsps OBJECT-TYPE SYNTAX Counter32 UNITS "failed logins" MAX-ACCESS read-only STATUS current DESCRIPTION "The count of Login Response PDUs with status class 0x01, Redirection, received by this initiator." ::= { cIscsiInitiatorLoginStatsEntry 3 } cIscsiIntrLoginAuthFailRsps OBJECT-TYPE SYNTAX Counter32 UNITS "failed logins" MAX-ACCESS read-only STATUS current DESCRIPTION "The count of Login Response PDUs with status class 0x201, Authentication Failed, received by this initiator." ::= { cIscsiInitiatorLoginStatsEntry 4 } cIscsiIntrLoginAuthenticateFails OBJECT-TYPE SYNTAX Counter32 UNITS "failed logins" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the initiator has aborted a login because the target could not be authenticated. No response is generated. If this counter is incremented, an cIscsiIntrLoginFailure notification should be generated." ::= { cIscsiInitiatorLoginStatsEntry 5 } cIscsiIntrLoginNegotiateFails OBJECT-TYPE SYNTAX Counter32 UNITS "failed logins" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the initiator has aborted a login because parameter negotiation with the target failed. No response is generated. If this counter is incremented, an cIscsiIntrLoginFailure notification should be generated." ::= { cIscsiInitiatorLoginStatsEntry 6 } -- Initiator Logout Stats Table cIscsiInitiatorLogoutStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF CIscsiInitiatorLogoutStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "When an initiator attempts send a Logout command, the target responds with a Logout Response that carries a status code. This table contains a list of counters of Logout Response PDUs of each status code, that were received by each initiator belonging to this iSCSI instance present on this system." ::= { cIscsiInitiator 3 } cIscsiInitiatorLogoutStatsEntry OBJECT-TYPE SYNTAX CIscsiInitiatorLogoutStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing counters of Logout Response PDUs of each status code, that were generated by this initiator." AUGMENTS { cIscsiInitiatorAttributesEntry } ::= { cIscsiInitiatorLogoutStatsTable 1 } CIscsiInitiatorLogoutStatsEntry ::= SEQUENCE { cIscsiIntrLogoutNormals Counter32, cIscsiIntrLogoutOthers Counter32 } cIscsiIntrLogoutNormals OBJECT-TYPE SYNTAX Counter32 UNITS "normal logouts" MAX-ACCESS read-only STATUS current DESCRIPTION "The count of Logout Command PDUs generated by this initiator with reason code 0 (closes the session)." ::= { cIscsiInitiatorLogoutStatsEntry 1 } cIscsiIntrLogoutOthers OBJECT-TYPE SYNTAX Counter32 UNITS "abnormal logouts" MAX-ACCESS read-only STATUS current DESCRIPTION "The count of Logout Command PDUs generated by this initiator with any status code other than 0." ::= { cIscsiInitiatorLogoutStatsEntry 2 } cIscsiIntrAuthorization OBJECT IDENTIFIER ::= { cIscsiObjects 10 } -- Initiator Authorization Attributes Table cIscsiIntrAuthAttributesTable OBJECT-TYPE SYNTAX SEQUENCE OF CIscsiIntrAuthAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of target identities which each initiator on the local system may access." ::= { cIscsiIntrAuthorization 1 } cIscsiIntrAuthAttributesEntry OBJECT-TYPE SYNTAX CIscsiIntrAuthAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing management information applicable to a particular initiator node's authorized target identity." INDEX { cIscsiInstIndex, cIscsiNodeIndex, cIscsiIntrAuthIndex } ::= { cIscsiIntrAuthAttributesTable 1 } CIscsiIntrAuthAttributesEntry ::= SEQUENCE { cIscsiIntrAuthIndex Unsigned32, cIscsiIntrAuthRowStatus RowStatus, cIscsiIntrAuthIdentity RowPointer } cIscsiIntrAuthIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer used to uniquely identify a particular initiator node's authorized target identity within an iSCSI instance present on the local system." ::= { cIscsiIntrAuthAttributesEntry 1 } cIscsiIntrAuthRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-only STATUS current DESCRIPTION "The status of the row." ::= { cIscsiIntrAuthAttributesEntry 2 } cIscsiIntrAuthIdentity OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-only STATUS current DESCRIPTION "A pointer to the corresponding IPS-AUTH MIB user entry to which this initiator node should attempt to establish an iSCSI session." REFERENCE "IPS-AUTH MIB" ::= { cIscsiIntrAuthAttributesEntry 3 } cIscsiSession OBJECT IDENTIFIER ::= { cIscsiObjects 11 } -- Session Attributes Table cIscsiSessionAttributesTable OBJECT-TYPE SYNTAX SEQUENCE OF CIscsiSessionAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of sessions belonging to each iSCSI instance present on the system." ::= { cIscsiSession 1 } cIscsiSessionAttributesEntry OBJECT-TYPE SYNTAX CIscsiSessionAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing management information applicable to a particular session." INDEX { cIscsiInstIndex, cIscsiNodeIndex, cIscsiSsnIndex } ::= { cIscsiSessionAttributesTable 1 } CIscsiSessionAttributesEntry ::= SEQUENCE { cIscsiSsnIndex Unsigned32, cIscsiSsnDirection INTEGER, cIscsiSsnInitiatorName SnmpAdminString, cIscsiSsnTargetName SnmpAdminString, cIscsiSsnTsih Unsigned32, cIscsiSsnIsid OCTET STRING, cIscsiSsnInitiatorAlias SnmpAdminString, cIscsiSsnTargetAlias SnmpAdminString, cIscsiSsnInitialR2T TruthValue, cIscsiSsnBidiInitialR2T TruthValue, cIscsiSsnImmediateData TruthValue, cIscsiSsnType INTEGER, cIscsiSsnMaxOutstandingR2T Unsigned32, cIscsiSsnFirstBurstSize Unsigned32, cIscsiSsnMaxBurstSize Unsigned32, cIscsiSsnConnectionNumber Gauge32, cIscsiSsnAuthIdentity RowPointer, cIscsiSsnDataSequenceInOrder TruthValue, cIscsiSsnDataPduInOrder TruthValue, cIscsiSsnErrorRecoveryLevel Unsigned32 } cIscsiSsnIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer used to uniquely identify a particular session within an iSCSI instance present on the local system." ::= { cIscsiSessionAttributesEntry 1 } cIscsiSsnDirection OBJECT-TYPE SYNTAX INTEGER { inboundSession(1), outboundSession(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Direction of iSCSI session: InboundSession - session is established from an external initiator to a target within this iSCSI instance. OutboundSession - session is established from an initiator within this iSCSI instance to an external target." ::= { cIscsiSessionAttributesEntry 2 } cIscsiSsnInitiatorName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "If cIscsiSsnDirection is Inbound, this object is an octet string that will contain the name of the remote initiator. If cIscsiSsnDirection is Outbound, this object will contain a zero-length string." ::= { cIscsiSessionAttributesEntry 3 } cIscsiSsnTargetName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "If cIscsiSsnDirection is Outbound, this object is an octet string that will contain the name of the remote target. If cIscsiSsnDirection is Inbound, this object will contain a zero-length string." ::= { cIscsiSessionAttributesEntry 4 } cIscsiSsnTsih OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The target-defined identification handle for this session." ::= { cIscsiSessionAttributesEntry 5 } cIscsiSsnIsid OBJECT-TYPE SYNTAX OCTET STRING (SIZE(6)) MAX-ACCESS read-only STATUS current DESCRIPTION "The initiator-defined portion of the iSCSI Session ID." ::= { cIscsiSessionAttributesEntry 6 } cIscsiSsnInitiatorAlias OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "An octet string that gives the alias communicated by the initiator end of the session during the login phase. If no alias exists, the value is a zero-length string." ::= { cIscsiSessionAttributesEntry 7 } cIscsiSsnTargetAlias OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "An octet string that gives the alias communicated by the target end of the session during the login phase. If no alias exists, the value is a zero-length string." ::= { cIscsiSessionAttributesEntry 8 } cIscsiSsnInitialR2T OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "If set to true, indicates that the initiator must wait for an R2T before sending to the target. If set to false, the initiator may send data immediately, within limits set by cIscsiSsnFirstBurstSize and the expected data transfer length of the request. Default is true." ::= { cIscsiSessionAttributesEntry 9 } cIscsiSsnBidiInitialR2T OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "If set to true, indicates that the initiator must wait for an R2T before sending data to the target within a bi-directional (both read and write) request. If false, the initiator may send unsolicited write data as part of the request." ::= { cIscsiSessionAttributesEntry 10 } cIscsiSsnImmediateData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the initiator and target have agreed to support immediate data on this session." ::= { cIscsiSessionAttributesEntry 11 } cIscsiSsnType OBJECT-TYPE SYNTAX INTEGER { normalSession(1), discoverySession(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Type of iSCSI session: normalSession - session is a normal iSCSI session discoverySession - session is being used only for discovery." DEFVAL { normalSession } ::= { cIscsiSessionAttributesEntry 12 } cIscsiSsnMaxOutstandingR2T OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of outstanding request-to-transmit (R2T)s per task within this session." ::= { cIscsiSessionAttributesEntry 13 } cIscsiSsnFirstBurstSize OBJECT-TYPE SYNTAX Unsigned32 (512..16777215) UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum length supported for unsolicited data sent within this session." DEFVAL { 65536 } ::= { cIscsiSessionAttributesEntry 14 } cIscsiSsnMaxBurstSize OBJECT-TYPE SYNTAX Unsigned32 (512..16777215) UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of bytes which can be sent within a single sequence of Data-In or Data-Out PDUs." DEFVAL { 262144 } ::= { cIscsiSessionAttributesEntry 15 } cIscsiSsnConnectionNumber OBJECT-TYPE SYNTAX Gauge32 (1..65535) UNITS "connections" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of transport protocol connections that currently belong to this session." ::= { cIscsiSessionAttributesEntry 16 } cIscsiSsnAuthIdentity OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains a row in the IPS-AUTH MIB which identifies the authentication method being used on this session, as communicated during the login phase." REFERENCE "IPS-AUTH MIB" ::= { cIscsiSessionAttributesEntry 17 } cIscsiSsnDataSequenceInOrder OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "False indicates that iSCSI data PDU sequences may be transferred in any order. True indicates that data PDU sequences must be transferred using continuously increasing offsets, except during error recovery." ::= { cIscsiSessionAttributesEntry 18 } cIscsiSsnDataPduInOrder OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "False indicates that iSCSI data PDUs within sequences may be in any order. True indicates that data PDUs within sequences must be at continuously increasing addresses, with no gaps or overlay between PDUs. Default is true." ::= { cIscsiSessionAttributesEntry 19 } cIscsiSsnErrorRecoveryLevel OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The level of error recovery negotiated between the initiator and the target. Higher numbers represent more detailed recovery schemes." ::= { cIscsiSessionAttributesEntry 20 } -- Session Stats Table cIscsiSessionStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF CIscsiSessionStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of general iSCSI traffic counters for each of the sessions present on the system." ::= { cIscsiSession 2 } cIscsiSessionStatsEntry OBJECT-TYPE SYNTAX CIscsiSessionStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing general iSCSI traffic counters for a particular session." AUGMENTS { cIscsiSessionAttributesEntry } ::= { cIscsiSessionStatsTable 1 } CIscsiSessionStatsEntry ::= SEQUENCE { cIscsiSsnCmdPdus Counter32, cIscsiSsnRspPdus Counter32, cIscsiSsnTxDataOctets Counter64, cIscsiSsnRxDataOctets Counter64 } cIscsiSsnCmdPdus OBJECT-TYPE SYNTAX Counter32 UNITS "PDUs" MAX-ACCESS read-only STATUS current DESCRIPTION "The count of Command PDUs transferred on this session." ::= { cIscsiSessionStatsEntry 1 } cIscsiSsnRspPdus OBJECT-TYPE SYNTAX Counter32 UNITS "PDUs" MAX-ACCESS read-only STATUS current DESCRIPTION "The count of Response PDUs transferred on this session." ::= { cIscsiSessionStatsEntry 2 } cIscsiSsnTxDataOctets OBJECT-TYPE SYNTAX Counter64 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The count of data octets that were transmitted by the local iSCSI node on this session." ::= { cIscsiSessionStatsEntry 3 } cIscsiSsnRxDataOctets OBJECT-TYPE SYNTAX Counter64 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The count of data octets that were received by the local iSCSI node on this session." ::= { cIscsiSessionStatsEntry 4 } -- Session Connection Error Stats Table cIscsiSessionCxnErrorStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF CIscsiSessionCxnErrorStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of error counters for each of the sessions present on this system." ::= { cIscsiSession 3 } cIscsiSessionCxnErrorStatsEntry OBJECT-TYPE SYNTAX CIscsiSessionCxnErrorStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing error counters for a particular session." AUGMENTS { cIscsiSessionAttributesEntry } ::= { cIscsiSessionCxnErrorStatsTable 1 } CIscsiSessionCxnErrorStatsEntry ::= SEQUENCE { cIscsiSsnDigestErrors Counter32, cIscsiSsnCxnTimeoutErrors Counter32 } cIscsiSsnDigestErrors OBJECT-TYPE SYNTAX Counter32 UNITS "PDUs" MAX-ACCESS read-only STATUS current DESCRIPTION "The count of PDUs which were received on the session and contained header or data digest errors." ::= { cIscsiSessionCxnErrorStatsEntry 1 } cIscsiSsnCxnTimeoutErrors OBJECT-TYPE SYNTAX Counter32 UNITS "sequences" MAX-ACCESS read-only STATUS current DESCRIPTION "The count of connections within this session which have been terminated due to timeout." ::= { cIscsiSessionCxnErrorStatsEntry 2 } cIscsiConnection OBJECT IDENTIFIER ::= { cIscsiObjects 12 } -- Connection Attributes Table cIscsiConnectionAttributesTable OBJECT-TYPE SYNTAX SEQUENCE OF CIscsiConnectionAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of connections belonging to each iSCSI instance present on the system." ::= { cIscsiConnection 1 } cIscsiConnectionAttributesEntry OBJECT-TYPE SYNTAX CIscsiConnectionAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing management information applicable to a particular connection." INDEX { cIscsiInstIndex, cIscsiNodeIndex, cIscsiSsnIndex, cIscsiCxnIndex } ::= { cIscsiConnectionAttributesTable 1 } CIscsiConnectionAttributesEntry ::= SEQUENCE { cIscsiCxnIndex Unsigned32, cIscsiCxnCid Unsigned32, cIscsiCxnState INTEGER, cIscsiCxnLocalAddrType InetAddressType, cIscsiCxnLocalAddr InetAddress, cIscsiCxnProtocol CIscsiTransportProtocols, cIscsiCxnLocalPort Unsigned32, cIscsiCxnRemoteAddrType InetAddressType, cIscsiCxnRemoteAddr InetAddress, cIscsiCxnRemotePort Unsigned32, cIscsiCxnMaxRecvDataSegLength Unsigned32, cIscsiCxnHeaderIntegrity CIscsiDigestMethod, cIscsiCxnDataIntegrity CIscsiDigestMethod, cIscsiCxnRecvMarker TruthValue, cIscsiCxnSendMarker TruthValue } cIscsiCxnIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer used to uniquely identify a particular connection of a particular session within an iSCSI instance present on the local system." ::= { cIscsiConnectionAttributesEntry 1 } cIscsiCxnCid OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The iSCSI Connection ID for this connection." ::= { cIscsiConnectionAttributesEntry 2 } cIscsiCxnState OBJECT-TYPE SYNTAX INTEGER { login(1), full(2), logout(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current state of this connection, from an iSCSI negotiation point of view. Here are the states: login - The transport protocol connection has been established, but a valid iSCSI login response with the final bit set has not been sent or received. full - A valid iSCSI login response with the final bit set has been sent or received. logout - A valid iSCSI logout command has been sent or received, but the transport protocol connection has not yet been closed." ::= { cIscsiConnectionAttributesEntry 3 } cIscsiCxnLocalAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of Internet Network Address in cIscsiCxnLocalAddr." ::= { cIscsiConnectionAttributesEntry 4 } cIscsiCxnLocalAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The local Internet Network Address used by this connection." ::= { cIscsiConnectionAttributesEntry 5 } cIscsiCxnProtocol OBJECT-TYPE SYNTAX CIscsiTransportProtocols MAX-ACCESS read-only STATUS current DESCRIPTION "The transport protocol over which this connection is running." DEFVAL { 6 } -- TCP ::= { cIscsiConnectionAttributesEntry 6 } cIscsiCxnLocalPort OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The local transport protocol port used by this connection." ::= { cIscsiConnectionAttributesEntry 7 } cIscsiCxnRemoteAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of Internet Network Address in cIscsiCxnRemoteAddr." ::= { cIscsiConnectionAttributesEntry 8 } cIscsiCxnRemoteAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The remote Internet Network Address used by this connection." ::= { cIscsiConnectionAttributesEntry 9 } cIscsiCxnRemotePort OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The remote transport protocol port used by this connection." ::= { cIscsiConnectionAttributesEntry 10 } cIscsiCxnMaxRecvDataSegLength OBJECT-TYPE SYNTAX Unsigned32 (512..16777215) UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum data payload size supported for command or data PDUs in use within this connection. Note that the size of reported in bytes even though the negotiation is in 512k blocks." DEFVAL { 8192 } ::= { cIscsiConnectionAttributesEntry 11 } cIscsiCxnHeaderIntegrity OBJECT-TYPE SYNTAX CIscsiDigestMethod MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the iSCSI header digest scheme in use within this connection." ::= { cIscsiConnectionAttributesEntry 12 } cIscsiCxnDataIntegrity OBJECT-TYPE SYNTAX CIscsiDigestMethod MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the iSCSI data digest scheme in use within this connection." ::= { cIscsiConnectionAttributesEntry 13 } cIscsiCxnRecvMarker OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether or not this connection is receiving markers in in its incoming data stream." ::= { cIscsiConnectionAttributesEntry 14 } cIscsiCxnSendMarker OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether or not this connection is inserting markers in in its outgoing data stream." ::= { cIscsiConnectionAttributesEntry 15 } -- Notifications cIscsiNotificationsPrefix OBJECT IDENTIFIER ::= { cIscsiNotifications 0 } cIscsiTgtLoginFailure NOTIFICATION-TYPE OBJECTS { cIscsiTgtLoginFailures, cIscsiTgtLastFailureType, cIscsiTgtLastIntrFailureName, cIscsiTgtLastIntrFailureAddrType, cIscsiTgtLastIntrFailureAddr } STATUS current DESCRIPTION "Sent when a login is failed by a target. The implementation of this trap should not send more than 3 notifications of this type in any 10 second time span." ::= { cIscsiNotificationsPrefix 1 } cIscsiIntrLoginFailure NOTIFICATION-TYPE OBJECTS { cIscsiIntrLoginFailures, cIscsiIntrLastFailureType, cIscsiIntrLastTgtFailureName, cIscsiIntrLastTgtFailureAddrType, cIscsiIntrLastTgtFailureAddr } STATUS current DESCRIPTION "Sent when a login is failed by a initiator. The implementation of this trap should not send more than 3 notifications of this type in any 10 second time span." ::= { cIscsiNotificationsPrefix 2 } cIscsiInstSessionFailure NOTIFICATION-TYPE OBJECTS { cIscsiInstSsnFailures, cIscsiInstLastSsnFailureType, cIscsiInstLastSsnRmtNodeName } STATUS current DESCRIPTION "Sent when an active session is failed by either the initiator or the target. The implementation of this trap should not send more than 3 notifications of this type in any 10 second time span." ::= { cIscsiNotificationsPrefix 3 } -- Conformance Statements cIscsiGroups OBJECT IDENTIFIER ::= { cIscsiConformance 1 } cIscsiInstanceAttributesGroup OBJECT-GROUP OBJECTS { cIscsiInstDescr, cIscsiInstVersionMin, cIscsiInstVersionMax, cIscsiInstVendorID, cIscsiInstVendorVersion, cIscsiInstPortalNumber, cIscsiInstNodeNumber, cIscsiInstSessionNumber, cIscsiInstSsnFailures, cIscsiInstLastSsnFailureType, cIscsiInstLastSsnRmtNodeName } STATUS current DESCRIPTION "A collection of objects providing information about iSCSI instances." ::= { cIscsiGroups 1 } cIscsiInstanceSsnErrorStatsGroup OBJECT-GROUP OBJECTS { cIscsiInstSsnDigestErrors, cIscsiInstSsnCxnTimeoutErrors, cIscsiInstSsnFormatErrors } STATUS current DESCRIPTION "A collection of objects providing information about errors that have caused a session failure for an iSCSI instance." ::= { cIscsiGroups 2 } cIscsiPortalAttributesGroup OBJECT-GROUP OBJECTS { cIscsiPortalRowStatus, cIscsiPortalRoles, cIscsiPortalAddrType, cIscsiPortalAddr, cIscsiPortalProtocol, cIscsiPortalMaxRecvDataSegLength, cIscsiPortalPrimaryHdrDigest, cIscsiPortalPrimaryDataDigest, cIscsiPortalSecondaryHdrDigest, cIscsiPortalSecondaryDataDigest, cIscsiPortalRecvMarker } STATUS current DESCRIPTION "A collection of objects providing information about the transport protocol endpoints of the local targets." ::= { cIscsiGroups 3 } cIscsiTgtPortalAttributesGroup OBJECT-GROUP OBJECTS { cIscsiTgtPortalPort, cIscsiTgtPortalTag } STATUS current DESCRIPTION "A collection of objects providing information about the transport protocol endpoints of the local targets." ::= { cIscsiGroups 4 } cIscsiIntrPortalAttributesGroup OBJECT-GROUP OBJECTS { cIscsiIntrPortalTag } STATUS current DESCRIPTION "A collection of objects providing information about the Internet Network Addresses of the local initiators." ::= { cIscsiGroups 5 } cIscsiNodeAttributesGroup OBJECT-GROUP OBJECTS { cIscsiNodeName, cIscsiNodeAlias, cIscsiNodeRoles, cIscsiNodeTransportType, cIscsiNodeInitialR2T, cIscsiNodeBidiInitialR2T, cIscsiNodeImmediateData, cIscsiNodeMaxOutstandingR2T, cIscsiNodeFirstBurstSize, cIscsiNodeMaxBurstSize, cIscsiNodeMaxConnections, cIscsiNodeDataSequenceInOrder, cIscsiNodeDataPduInOrder, cIscsiNodeDefaultTime2Wait, cIscsiNodeDefaultTime2Retain, cIscsiNodeErrorRecoveryLevel } STATUS current DESCRIPTION "A collection of objects providing information about all local targets." ::= { cIscsiGroups 6 } cIscsiTargetAttributesGroup OBJECT-GROUP OBJECTS { cIscsiTgtLoginFailures, cIscsiTgtLastFailureTime, cIscsiTgtLastFailureType, cIscsiTgtLastIntrFailureName, cIscsiTgtLastIntrFailureAddrType, cIscsiTgtLastIntrFailureAddr } STATUS current DESCRIPTION "A collection of objects providing information about all local targets." ::= { cIscsiGroups 7 } cIscsiTargetLoginStatsGroup OBJECT-GROUP OBJECTS { cIscsiTgtLoginAccepts, cIscsiTgtLoginOtherFails, cIscsiTgtLoginRedirects, cIscsiTgtLoginAuthorizeFails, cIscsiTgtLoginAuthenticateFails, cIscsiTgtLoginNegotiateFails } STATUS current DESCRIPTION "A collection of objects providing information about all login attempts by remote initiators to local targets." ::= { cIscsiGroups 8 } cIscsiTargetLogoutStatsGroup OBJECT-GROUP OBJECTS { cIscsiTgtLogoutNormals, cIscsiTgtLogoutOthers } STATUS current DESCRIPTION "A collection of objects providing information about all logout events between remote initiators to local targets." ::= { cIscsiGroups 9 } cIscsiTargetAuthGroup OBJECT-GROUP OBJECTS { cIscsiTgtAuthRowStatus, cIscsiTgtAuthIdentity } STATUS current DESCRIPTION "." ::= { cIscsiGroups 10 } cIscsiInitiatorAttributesGroup OBJECT-GROUP OBJECTS { cIscsiIntrLoginFailures, cIscsiIntrLastFailureTime, cIscsiIntrLastFailureType, cIscsiIntrLastTgtFailureName, cIscsiIntrLastTgtFailureAddrType, cIscsiIntrLastTgtFailureAddr } STATUS current DESCRIPTION "A collection of objects providing information about all local initiators." ::= { cIscsiGroups 11 } cIscsiInitiatorLoginStatsGroup OBJECT-GROUP OBJECTS { cIscsiIntrLoginAcceptRsps, cIscsiIntrLoginOtherFailRsps, cIscsiIntrLoginRedirectRsps, cIscsiIntrLoginAuthFailRsps, cIscsiIntrLoginAuthenticateFails, cIscsiIntrLoginNegotiateFails } STATUS current DESCRIPTION "A collection of objects providing information about all login attempts by local initiators to remote targets." ::= { cIscsiGroups 12 } cIscsiInitiatorLogoutStatsGroup OBJECT-GROUP OBJECTS { cIscsiIntrLogoutNormals, cIscsiIntrLogoutOthers } STATUS current DESCRIPTION "A collection of objects providing information about all logout events between local initiators to remote targets." ::= { cIscsiGroups 13 } cIscsiInitiatorAuthGroup OBJECT-GROUP OBJECTS { cIscsiIntrAuthRowStatus, cIscsiIntrAuthIdentity } STATUS current DESCRIPTION "." ::= { cIscsiGroups 14 } cIscsiSessionAttributesGroup OBJECT-GROUP OBJECTS { cIscsiSsnDirection, cIscsiSsnInitiatorName, cIscsiSsnTargetName, cIscsiSsnTsih, cIscsiSsnIsid, cIscsiSsnInitiatorAlias, cIscsiSsnTargetAlias, cIscsiSsnInitialR2T, cIscsiSsnBidiInitialR2T, cIscsiSsnImmediateData, cIscsiSsnType, cIscsiSsnMaxOutstandingR2T, cIscsiSsnFirstBurstSize, cIscsiSsnMaxBurstSize, cIscsiSsnConnectionNumber, cIscsiSsnAuthIdentity, cIscsiSsnDataSequenceInOrder, cIscsiSsnDataPduInOrder, cIscsiSsnErrorRecoveryLevel } STATUS current DESCRIPTION "A collection of objects providing information applicable to all sessions." ::= { cIscsiGroups 15 } cIscsiSessionStatsGroup OBJECT-GROUP OBJECTS { cIscsiSsnCmdPdus, cIscsiSsnRspPdus, cIscsiSsnTxDataOctets, cIscsiSsnRxDataOctets } STATUS current DESCRIPTION "A collection of objects providing information about message and data traffic for all sessions." ::= { cIscsiGroups 16 } cIscsiSessionCxnErrorStatsGroup OBJECT-GROUP OBJECTS { cIscsiSsnDigestErrors, cIscsiSsnCxnTimeoutErrors } STATUS current DESCRIPTION "A collection of objects providing information about connection errors for all sessions." ::= { cIscsiGroups 17 } cIscsiConnectionAttributesGroup OBJECT-GROUP OBJECTS { cIscsiCxnCid, cIscsiCxnState, cIscsiCxnProtocol, cIscsiCxnLocalAddrType, cIscsiCxnLocalAddr, cIscsiCxnLocalPort, cIscsiCxnRemoteAddrType, cIscsiCxnRemoteAddr, cIscsiCxnRemotePort, cIscsiCxnMaxRecvDataSegLength, cIscsiCxnHeaderIntegrity, cIscsiCxnDataIntegrity, cIscsiCxnRecvMarker, cIscsiCxnSendMarker } STATUS current DESCRIPTION "A collection of objects providing information about all connections used by all sessions." ::= { cIscsiGroups 18 } cIscsiTgtLgnNotificationsGroup NOTIFICATION-GROUP NOTIFICATIONS { cIscsiTgtLoginFailure } STATUS current DESCRIPTION "A collection of notifications which indicate a login failure from a remote initiator to a local target." ::= { cIscsiGroups 19 } cIscsiIntrLgnNotificationsGroup NOTIFICATION-GROUP NOTIFICATIONS { cIscsiIntrLoginFailure } STATUS current DESCRIPTION "A collection of notifications which indicate a login failure from a local initiator to a remote target." ::= { cIscsiGroups 20 } cIscsiSsnFlrNotificationsGroup NOTIFICATION-GROUP NOTIFICATIONS { cIscsiInstSessionFailure } STATUS current DESCRIPTION "A collection of notifications which indicate session failures occurring after login." ::= { cIscsiGroups 21 } cIscsiCompliances OBJECT IDENTIFIER ::= { cIscsiConformance 2 } cIscsiComplianceV1 MODULE-COMPLIANCE STATUS current DESCRIPTION "Initial version of compliance statement based on initial version of MIB. If an implementation can be both a target and an initiator, all groups are mandatory." MODULE -- this module MANDATORY-GROUPS { cIscsiInstanceAttributesGroup, cIscsiPortalAttributesGroup, cIscsiNodeAttributesGroup, cIscsiSessionAttributesGroup, cIscsiSessionStatsGroup, cIscsiSessionCxnErrorStatsGroup, cIscsiConnectionAttributesGroup, cIscsiSsnFlrNotificationsGroup, cIscsiInstanceSsnErrorStatsGroup } -- Conditionally mandatory groups to be included with -- the mandatory groups when the implementation has -- iSCSI target facilities. GROUP cIscsiTgtPortalAttributesGroup DESCRIPTION "This group is mandatory for all iSCSI implementations that have iSCSI target facilities." GROUP cIscsiTargetAttributesGroup DESCRIPTION "This group is mandatory for all iSCSI implementations that have iSCSI target facilities." GROUP cIscsiTargetLoginStatsGroup DESCRIPTION "This group is mandatory for all iSCSI implementations that have iSCSI target facilities." GROUP cIscsiTargetLogoutStatsGroup DESCRIPTION "This group is mandatory for all iSCSI implementations that have iSCSI target facilities." GROUP cIscsiTgtLgnNotificationsGroup DESCRIPTION "This group is mandatory for all iSCSI implementations that have iSCSI target facilities." GROUP cIscsiTargetAuthGroup DESCRIPTION "This group is mandatory for all iSCSI implementations that have iSCSI target facilities." -- Conditionally mandatory groups to be included with -- the mandatory groups when the implementation has -- iSCSI initiator facilities. GROUP cIscsiIntrPortalAttributesGroup DESCRIPTION "This group is mandatory for all iSCSI implementations that have iSCSI initiator facilities." GROUP cIscsiInitiatorAttributesGroup DESCRIPTION "This group is mandatory for all iSCSI implementations that have iSCSI initiator facilities." GROUP cIscsiInitiatorLoginStatsGroup DESCRIPTION "This group is mandatory for all iSCSI implementations that have iSCSI initiator facilities." GROUP cIscsiInitiatorLogoutStatsGroup DESCRIPTION "This group is mandatory for all iSCSI implementations that have iSCSI initiator facilities." GROUP cIscsiIntrLgnNotificationsGroup DESCRIPTION "This group is mandatory for all iSCSI implementations that have iSCSI initiator facilities." GROUP cIscsiInitiatorAuthGroup DESCRIPTION "This group is mandatory for all iSCSI implementations that have iSCSI initiator facilities." ::= { cIscsiCompliances 1 } END