-- ***************************************************************** -- CISCO-IPSLA-VIDEO-MIB.my: IP SLA Video MIB file -- -- March 2010, Sohayb Aiyub -- -- Copyright (c) 2006-2007, 2010 by cisco Systems Inc. -- All rights reserved. -- -- ***************************************************************** CISCO-IPSLA-VIDEO-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Counter32, Gauge32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF TimeStamp FROM SNMPv2-TC SnmpAdminString FROM SNMP-FRAMEWORK-MIB rttMonCtrlAdminIndex FROM CISCO-RTTMON-MIB RttResponseSense FROM CISCO-RTTMON-TC-MIB ciscoMgmt FROM CISCO-SMI; ciscoIpslaVideoMIB MODULE-IDENTITY LAST-UPDATED "201006110000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-ipsla@cisco.com" DESCRIPTION "IP SLA is a capability which utilizes active monitoring for network performance. It can be used for network troubleshooting, network assessment and health monitoring. This MIB defines a collection of statistics resulting from the 'video' IP SLA operation. The Video Statistics table names are: cipslaLatestVideoStatsTable --- Contains only the latest statistics cipslaVideoAggStatsTable --- Contains aggregated statistics To create the Video operation, set rttMonEchoAdminProtocol (defined in CISCO-RTTMON-MIB) object to 'videoAppl'. Once the operation has been scheduled, both cipslaLatestVideoStatsTable and cipslaVideoAggStatsTable will be populated. Glossary: IP SLA - Cisco IOS IP Service Level Agreements IP SLA operation - Refers to the 'video' operation supported by IP SLA. RTT - Round Trip Time" REVISION "201006110000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 744 } -- Textual Conventions definition will be defined before this line ciscoIpslaVideoMIBNotifs OBJECT IDENTIFIER ::= { ciscoIpslaVideoMIB 0 } ciscoIpslaVideoMIBObjects OBJECT IDENTIFIER ::= { ciscoIpslaVideoMIB 1 } ciscoIpslaVideoMIBConform OBJECT IDENTIFIER ::= { ciscoIpslaVideoMIB 2 } cipslaVideoLatestOper OBJECT IDENTIFIER ::= { ciscoIpslaVideoMIBObjects 1 } cipslaVideoStats OBJECT IDENTIFIER ::= { ciscoIpslaVideoMIBObjects 2 } -- LatestVideoJitterOper Table cipslaLatestVideoStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF IpslaVideoJitterLatestStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The 'video' operation sends out video streams at the frequency specified by rttMonCtrlAdminFrequency. This table contains the statistics calculated for the latest video packets. Each conceptual row in this table corresponds to an 'video' operation defined in rttMonCtrlAdminTable and has same index as rttMonCtrlAdminTable." ::= { cipslaVideoLatestOper 1 } cipslaLatestVideoStatsEntry OBJECT-TYPE SYNTAX IpslaVideoJitterLatestStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A collection of objects that record the latest Video jitter operation. An entry is created only when the following objects are valid. - rttMonCtrlAdminRttType - rttMonEchoAdminProtocol The entry will start to collect data when rttMonCtrlAdminStatus is in 'active' state. The entry will be removed when the rttMonCtrlAdminStatus is changed to 'destroy' state." INDEX { rttMonCtrlAdminIndex } ::= { cipslaLatestVideoStatsTable 1 } IpslaVideoJitterLatestStatsEntry ::= SEQUENCE { cipslaLatestVideoMinPosSD Gauge32, cipslaLatestVideoMaxPosSD Gauge32, cipslaLatestVideoNumPosSD Gauge32, cipslaLatestVideoSumPosSD Gauge32, cipslaLatestVideoSum2PosSD Gauge32, cipslaLatestVideoMinNegSD Gauge32, cipslaLatestVideoMaxNegSD Gauge32, cipslaLatestVideoNumNegSD Gauge32, cipslaLatestVideoSumNegSD Gauge32, cipslaLatestVideoSum2NegSD Gauge32, cipslaLatestVideoPktLossSD Gauge32, cipslaLatestVideoPktOutSeq Gauge32, cipslaLatestVideoSense RttResponseSense, cipslaLatestVideoOWSumSD Gauge32, cipslaLatestVideoOWSum2SD Gauge32, cipslaLatestVideoOWMinSD Gauge32, cipslaLatestVideoOWMaxSD Gauge32, cipslaLatestVideoNumOWSD Gauge32, cipslaLatestVideoAvgJitterSD Gauge32, cipslaLatestVideoIAJOut Gauge32, cipslaLatestVideoErrSenseDescr SnmpAdminString, cipslaLatestVideoUnSyncRTs Counter32, cipslaLatestVideoOWSumSDHigh Gauge32, cipslaLatestVideoOWSum2SDHigh Gauge32, cipslaLatestVideoNTPState INTEGER, cipslaLatestVideoIPDVAvgSDJ Gauge32, cipslaLatestVideoOWAvgSD Gauge32, cipslaLatestVideoPktLateArrival Gauge32 } cipslaLatestVideoMinPosSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum of all positive jitter values for packets sent from source to destination." ::= { cipslaLatestVideoStatsEntry 1 } cipslaLatestVideoMaxPosSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum of all positive jitter values for packets sent from source to destination." ::= { cipslaLatestVideoStatsEntry 2 } cipslaLatestVideoNumPosSD OBJECT-TYPE SYNTAX Gauge32 UNITS "occurrences" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of all positive jitter values for packets sent from source to destination." ::= { cipslaLatestVideoStatsEntry 3 } cipslaLatestVideoSumPosSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of all positive jitter values for packets sent source to destination. The number of such values is stored in cipslaLatestVideoNumPosSD." ::= { cipslaLatestVideoStatsEntry 4 } cipslaLatestVideoSum2PosSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of square of all positive jitter values for packets sent from source to destination." ::= { cipslaLatestVideoStatsEntry 5 } cipslaLatestVideoMinNegSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum of absolute values of all negative jitter values for packets sent from source to destination." ::= { cipslaLatestVideoStatsEntry 6 } cipslaLatestVideoMaxNegSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum of absolute values of all negative jitter values for packets sent from source to destination." ::= { cipslaLatestVideoStatsEntry 7 } cipslaLatestVideoNumNegSD OBJECT-TYPE SYNTAX Gauge32 UNITS "occurrences" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of all negative jitter values for packets sent from source to destination." ::= { cipslaLatestVideoStatsEntry 8 } cipslaLatestVideoSumNegSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of all negative jitter values for packets sent from source to destination. The number of such values is stored in cipslaLatestVideoNumNegSD." ::= { cipslaLatestVideoStatsEntry 9 } cipslaLatestVideoSum2NegSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of square of all negative jitter values for packets sent from source to destination." ::= { cipslaLatestVideoStatsEntry 10 } cipslaLatestVideoPktLossSD OBJECT-TYPE SYNTAX Gauge32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets lost when sent from source to destination." ::= { cipslaLatestVideoStatsEntry 11 } cipslaLatestVideoPktOutSeq OBJECT-TYPE SYNTAX Gauge32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets arrived out of sequence." ::= { cipslaLatestVideoStatsEntry 12 } cipslaLatestVideoSense OBJECT-TYPE SYNTAX RttResponseSense MAX-ACCESS read-only STATUS current DESCRIPTION "An application specific sense code for the completion status." ::= { cipslaLatestVideoStatsEntry 13 } cipslaLatestVideoOWSumSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of one way trip time from source to destination." ::= { cipslaLatestVideoStatsEntry 14 } cipslaLatestVideoOWSum2SD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of squares of one way trip time from source to destination." ::= { cipslaLatestVideoStatsEntry 15 } cipslaLatestVideoOWMinSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum of all one way trip time from source to destination." ::= { cipslaLatestVideoStatsEntry 16 } cipslaLatestVideoOWMaxSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum of all one way trip time from source to destination." ::= { cipslaLatestVideoStatsEntry 17 } cipslaLatestVideoNumOWSD OBJECT-TYPE SYNTAX Gauge32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of successful one way trip time measurements from source to destination." ::= { cipslaLatestVideoStatsEntry 18 } cipslaLatestVideoAvgJitterSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The average of positive and negative jitter values in Source-to-Destination direction." ::= { cipslaLatestVideoStatsEntry 19 } cipslaLatestVideoIAJOut OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Inter-arrival jitter (RFC 1889) at responder." REFERENCE "Refer to the following documents for the definition: RFC 1889, Section 6.3.1" ::= { cipslaLatestVideoStatsEntry 20 } cipslaLatestVideoErrSenseDescr OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "An sense description for the completion status of the latest video operation." ::= { cipslaLatestVideoStatsEntry 21 } cipslaLatestVideoUnSyncRTs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RTT operations that have completed with sender and responder out of sync with NTP. The NTP sync means the total of NTP offset on sender and responder is within configured tolerance level" ::= { cipslaLatestVideoStatsEntry 22 } cipslaLatestVideoOWSumSDHigh OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of one way latency from source to destination (high order 32 bits). The low order 32 bits are stored in cipslaLatestVideoOWSumSD." ::= { cipslaLatestVideoStatsEntry 23 } cipslaLatestVideoOWSum2SDHigh OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of squares of one way latency from source to destination (high order 32 bits). The low order 32 bits are stored in cipslaLatestVideoOWSum2SD." ::= { cipslaLatestVideoStatsEntry 24 } cipslaLatestVideoNTPState OBJECT-TYPE SYNTAX INTEGER { sync(1), outOfSync(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "A value of sync(1) means sender and responder was in sync with NTP. The NTP sync means the total of NTP offset on sender and responder is within configured tolerance level." ::= { cipslaLatestVideoStatsEntry 25 } cipslaLatestVideoIPDVAvgSDJ OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Source to Destination IPDV average jitter according to RFC 5481." REFERENCE "Refer to the following documents for the definition: Inter Packet Delay Variation, RFC 5481 (IPDV)" ::= { cipslaLatestVideoStatsEntry 26 } cipslaLatestVideoOWAvgSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The average latency value from source to destination." ::= { cipslaLatestVideoStatsEntry 27 } cipslaLatestVideoPktLateArrival OBJECT-TYPE SYNTAX Gauge32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets that arrived after the timeout." ::= { cipslaLatestVideoStatsEntry 28 } cipslaVideoAggStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF CipslaVideoAggStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The 'video' statistics table contains summarized information of the results for a conceptual control row. A rolling accumulated history of this information is maintained in a series of hourly 'group(s)'. When ipslaVideoAggStartTimeId groups exceeds the rttMonStatisticsAdminNumHourGroups value, the oldest corresponding hourly group will be deleted and will be replaced with the new ipslaVideoAggStatsStartTimeId hourly group." ::= { cipslaVideoStats 1 } cipslaVideoAggStatsEntry OBJECT-TYPE SYNTAX CipslaVideoAggStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry contains the objects which accumulate the results of a series of 'video' operations over a 60 minute time period or a time period stored in rttMonScheduleAdminRttLife, whichever is smaller. An entry is created only if when the following objects are valid. - rttMonCtrlAdminRttType - rttMonEchoAdminProtocol The entry will start to collect data when rttMonCtrlAdminStatus is in 'active' state. The entry will be removed when the rttMonCtrlAdminStatus is changed to 'destroy' state. cipslaVideoAggStartTimeId will be created at the beginning of the hour and will keep aggregating statistics until the end of the hour." INDEX { rttMonCtrlAdminIndex, cipslaVideoAggStartTimeId } ::= { cipslaVideoAggStatsTable 1 } CipslaVideoAggStatsEntry ::= SEQUENCE { cipslaVideoAggStartTimeId TimeStamp, cipslaVideoAggCompletions Counter32, cipslaVideoAggOverThresholds Counter32, cipslaVideoAggMinPosSD Gauge32, cipslaVideoAggMaxPosSD Gauge32, cipslaVideoAggNumPosSD Counter32, cipslaVideoAggSumPosSD Counter32, cipslaVideoAggSum2PosSDLow Counter32, cipslaVideoAggSum2PosSDHigh Counter32, cipslaVideoAggMinNegSD Gauge32, cipslaVideoAggMaxNegSD Gauge32, cipslaVideoAggNumNegSD Counter32, cipslaVideoAggSumNegSD Counter32, cipslaVideoAggSum2NegSDLow Counter32, cipslaVideoAggSum2NegSDHigh Counter32, cipslaVideoAggPktLossSD Counter32, cipslaVideoAggPktOutSeq Counter32, cipslaVideoAggPktSkipped Counter32, cipslaVideoAggErrors Counter32, cipslaVideoAggBusies Counter32, cipslaVideoAggOWSumSD Counter32, cipslaVideoAggOWSum2SDLow Counter32, cipslaVideoAggOWSum2SDHigh Counter32, cipslaVideoAggOWMinSD Gauge32, cipslaVideoAggOWMaxSD Gauge32, cipslaVideoAggNumOWSD Counter32, cipslaVideoAggAvgJSD Gauge32, cipslaVideoAggIAJOut Gauge32, cipslaVideoAggIAJIn Gauge32, cipslaVideoAggPktLateArrival Counter32, cipslaVideoAggUnSyncRTs Counter32, cipslaVideoAggOWSumSDHigh Counter32 } cipslaVideoAggStartTimeId OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of sysUpTime at the time when this row was created." ::= { cipslaVideoAggStatsEntry 1 } cipslaVideoAggCompletions OBJECT-TYPE SYNTAX Counter32 UNITS "completions" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of video operations that have completed successfully." ::= { cipslaVideoAggStatsEntry 2 } cipslaVideoAggOverThresholds OBJECT-TYPE SYNTAX Counter32 UNITS "operations" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of video operations that violate jitterAvg threshold which is defined in RttMonReactVar." ::= { cipslaVideoAggStatsEntry 3 } cipslaVideoAggMinPosSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum of absolute values of all positive jitter values for packets sent from source to destination." ::= { cipslaVideoAggStatsEntry 4 } cipslaVideoAggMaxPosSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum of absolute values of all positive jitter values for packets sent from source to destination." ::= { cipslaVideoAggStatsEntry 5 } cipslaVideoAggNumPosSD OBJECT-TYPE SYNTAX Counter32 UNITS "occurrences" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of all positive jitter values for packets sent from source to destination." ::= { cipslaVideoAggStatsEntry 6 } cipslaVideoAggSumPosSD OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of all positive jitter values for packets sent from source to destination. The number of such values is stored in ipslaVideoAggNumPosSDs." ::= { cipslaVideoAggStatsEntry 7 } cipslaVideoAggSum2PosSDLow OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of square of all positive jitter values for packets sent from source to destination (low order 32 bits)." ::= { cipslaVideoAggStatsEntry 8 } cipslaVideoAggSum2PosSDHigh OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of square of all positive jitter values for packets sent from source to destination (high order 32 bits)." ::= { cipslaVideoAggStatsEntry 9 } cipslaVideoAggMinNegSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum of all negative jitter values for packets sent from source to destination." ::= { cipslaVideoAggStatsEntry 10 } cipslaVideoAggMaxNegSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum of all negative jitter values for packets sent from source to destination." ::= { cipslaVideoAggStatsEntry 11 } cipslaVideoAggNumNegSD OBJECT-TYPE SYNTAX Counter32 UNITS "occurrences" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of all negative jitter values for packets sent from source to destination." ::= { cipslaVideoAggStatsEntry 12 } cipslaVideoAggSumNegSD OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of all negative jitter values for packets sent from source to destination. The number of such values is stored in ipslaVideoAggNumNegSDs." ::= { cipslaVideoAggStatsEntry 13 } cipslaVideoAggSum2NegSDLow OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of square of all negative jitter values for packets sent from source to destination (low order 32 bits)." ::= { cipslaVideoAggStatsEntry 14 } cipslaVideoAggSum2NegSDHigh OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of square of all negative jitter values for packets sent from source to destination (high order 32 bits)." ::= { cipslaVideoAggStatsEntry 15 } cipslaVideoAggPktLossSD OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of lost packets when sent from source to destination." ::= { cipslaVideoAggStatsEntry 16 } cipslaVideoAggPktOutSeq OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets arrived out of sequence." ::= { cipslaVideoAggStatsEntry 17 } cipslaVideoAggPktSkipped OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets that are skipped per operation because the router could not send the packet out." ::= { cipslaVideoAggStatsEntry 18 } cipslaVideoAggErrors OBJECT-TYPE SYNTAX Counter32 UNITS "errors" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of occasions when a video operation could not be initiated because of an internal error." ::= { cipslaVideoAggStatsEntry 19 } cipslaVideoAggBusies OBJECT-TYPE SYNTAX Counter32 UNITS "busies" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of occasions when a video operation could not be initiated because a previous video operation has not been completed." ::= { cipslaVideoAggStatsEntry 20 } cipslaVideoAggOWSumSD OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of one way trip time from source to destination." ::= { cipslaVideoAggStatsEntry 21 } cipslaVideoAggOWSum2SDLow OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of squares of one way trip time from source to destination (low order 32 bits)." ::= { cipslaVideoAggStatsEntry 22 } cipslaVideoAggOWSum2SDHigh OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of squares of one way trip time from source to destination (high order 32 bits)." ::= { cipslaVideoAggStatsEntry 23 } cipslaVideoAggOWMinSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum of all one way trip time from source to destination." ::= { cipslaVideoAggStatsEntry 24 } cipslaVideoAggOWMaxSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum of all one way trip time from source to destination." ::= { cipslaVideoAggStatsEntry 25 } cipslaVideoAggNumOWSD OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of one way trip time that are successfully measured from source to destination." ::= { cipslaVideoAggStatsEntry 26 } cipslaVideoAggAvgJSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The average of positive and negative jitter values in source-to-destination direction." ::= { cipslaVideoAggStatsEntry 27 } cipslaVideoAggIAJOut OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Inter-arrival jitter (RFC 1889) at responder" REFERENCE "Refer to the following documents for the definition: RFC 1889, Section 6.3.1" ::= { cipslaVideoAggStatsEntry 28 } cipslaVideoAggIAJIn OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Inter-arrival jitter (RFC 1889) at sender" REFERENCE "Refer to the following documents for the definition: RFC 1889, Section 6.3.1" ::= { cipslaVideoAggStatsEntry 29 } cipslaVideoAggPktLateArrival OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets that arrived after the timeout." ::= { cipslaVideoAggStatsEntry 30 } cipslaVideoAggUnSyncRTs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RTT operations that have completed with sender and responder out of sync with NTP. The NTP sync means the total of NTP offset on sender and responder is within configured tolerance level" ::= { cipslaVideoAggStatsEntry 31 } cipslaVideoAggOWSumSDHigh OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of one way times from source to destination (high order 32 bits). The low order 32 bits are stored in cipslaVideoAggOWSumSD." ::= { cipslaVideoAggStatsEntry 32 } ciscoIpslaVideoMIBCompliances OBJECT IDENTIFIER ::= { ciscoIpslaVideoMIBConform 1 } ciscoIpslaVideoMIBGroups OBJECT IDENTIFIER ::= { ciscoIpslaVideoMIBConform 2 } ciscoIpslaVideoMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "This is a default module-compliance containing default object groups." MODULE -- this module MANDATORY-GROUPS { ciscoIpslaVideoStatsGroup } ::= { ciscoIpslaVideoMIBCompliances 1 } -- Units of Conformance ciscoIpslaVideoStatsGroup OBJECT-GROUP OBJECTS { cipslaLatestVideoMinPosSD, cipslaLatestVideoMaxPosSD, cipslaLatestVideoNumPosSD, cipslaLatestVideoSumPosSD, cipslaLatestVideoSum2PosSD, cipslaLatestVideoMinNegSD, cipslaLatestVideoMaxNegSD, cipslaLatestVideoNumNegSD, cipslaLatestVideoSumNegSD, cipslaLatestVideoSum2NegSD, cipslaLatestVideoPktLossSD, cipslaLatestVideoPktOutSeq, cipslaLatestVideoSense, cipslaLatestVideoOWSumSD, cipslaLatestVideoOWSum2SD, cipslaLatestVideoOWMinSD, cipslaLatestVideoOWMaxSD, cipslaLatestVideoNumOWSD, cipslaLatestVideoAvgJitterSD, cipslaLatestVideoIAJOut, cipslaLatestVideoErrSenseDescr, cipslaLatestVideoUnSyncRTs, cipslaLatestVideoOWSumSDHigh, cipslaLatestVideoOWSum2SDHigh, cipslaLatestVideoNTPState, cipslaLatestVideoIPDVAvgSDJ, cipslaLatestVideoOWAvgSD, cipslaLatestVideoPktLateArrival, cipslaVideoAggCompletions, cipslaVideoAggOverThresholds, cipslaVideoAggMinPosSD, cipslaVideoAggMaxPosSD, cipslaVideoAggNumPosSD, cipslaVideoAggSumPosSD, cipslaVideoAggSum2PosSDLow, cipslaVideoAggSum2PosSDHigh, cipslaVideoAggMinNegSD, cipslaVideoAggMaxNegSD, cipslaVideoAggNumNegSD, cipslaVideoAggSumNegSD, cipslaVideoAggSum2NegSDLow, cipslaVideoAggSum2NegSDHigh, cipslaVideoAggPktLossSD, cipslaVideoAggPktOutSeq, cipslaVideoAggPktSkipped, cipslaVideoAggErrors, cipslaVideoAggBusies, cipslaVideoAggOWSumSD, cipslaVideoAggOWSum2SDLow, cipslaVideoAggOWSum2SDHigh, cipslaVideoAggOWMinSD, cipslaVideoAggOWMaxSD, cipslaVideoAggNumOWSD, cipslaVideoAggAvgJSD, cipslaVideoAggIAJOut, cipslaVideoAggIAJIn, cipslaVideoAggPktLateArrival, cipslaVideoAggUnSyncRTs, cipslaVideoAggOWSumSDHigh } STATUS current DESCRIPTION "A collection of statistics objects related to Video Probe." ::= { ciscoIpslaVideoMIBGroups 1 } END