-- ***************************************************************** -- CISCO-IPSLA-ETHERNET-MIB.my: IP SLA Ethernet MIB file -- -- February 2006, Minghui Zhu -- -- Copyright (c) 2006-2012 by cisco Systems Inc. -- All rights reserved. -- -- ***************************************************************** CISCO-IPSLA-ETHERNET-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Counter32, Gauge32, Unsigned32, TimeTicks, Counter64 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF TimeStamp, StorageType, RowStatus FROM SNMPv2-TC VlanId FROM Q-BRIDGE-MIB Dot1agCfmMaintDomainNameType, Dot1agCfmMaintDomainName FROM IEEE8021-CFM-MIB SnmpAdminString FROM SNMP-FRAMEWORK-MIB Layer2Cos FROM CISCO-TC rttMonCtrlAdminIndex FROM CISCO-RTTMON-MIB RttResponseSense, RttMonRttType, RttMonReactVar, RttMonCtrlIndex, RttMonIdLst FROM CISCO-RTTMON-TC-MIB ciscoMgmt FROM CISCO-SMI; ciscoIpSlaEthernetMIB MODULE-IDENTITY LAST-UPDATED "201205150000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems, Inc. Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 Tel: +1 800 553 NETS Email: cs-ipsla@cisco.com" DESCRIPTION "This MIB module consists of two parts. 1) Auto-Ethernet-CFM Control: |-- ipslaEthernetGrpCtrlTable |-- ipslaEthernetGrpReactTable 2) ethernetJitter Stats: |-- ipslaEtherJitterLatestStatsTable |-- ipslaEtherJitterAggStatsTable The first part defines a mechanism to manage IP SLA Auto-Ethernet-CFM operation. IP SLA is a capability which utilizes active monitoring for network perfomance. It can be used for network troubleshooting, network assessment and health monitoring. IEEE 802.1ag defines Connection Fault Management (CFM) for Ethernet layer. CFM can be used to detect, isolate and report the connectivity faults, and allows discovery and verification of the path through briges and LANs. Auto-Ethernet-CFM operation integrates the capabilities of IP SLA and IEEE 802.1ag. It's capable of discovering all the existing MEPs in a specified VLAN or Ethernet Virtual Connection within a specified maintenance domain. After which, it creates, configures, and schedules an IP SLA operation for each MEP automatically. IP SLA currently supports two types of operations for end-to-end Ethernet connectivity - 'ethernetPing' and 'ethernetJitter'. 'ethernetPing' can be used to monitor the connectivity and measure RTT by sending the regular 802.1ag loopback frame to a particular MEP. 'ethernetJitter' can be used to measure metrics such as RTT, Jitter, frame loss, one-way latency by sending multiple enhanced CFM frames at specified interval to a particular MEP. Without Auto-Ethernet-CFM operation, the two types of operations can also be created, configured, and scheduled manually through CISCO-RTTMON-MIB by specifing the target MEP's identifier in addition to the VLAN or Ethernet Virtual Connection and Maintenance Domain. With Auto-Ethernet-CFM operation, the two types of operations will be created automatically. The Auto-Ethernet-CFM will pass all the values specified in this module to the corresponding objects in CISCO-RTTMON-MIB for each MEP discovered. CISCO-IPSLA-ETHERNET-MIB CISCO-RTTMON-MIB ipslaEthernetGrpCtrlTable -> rttMonCtrlAdminTable | -> rttMonEchoAdminTable ipslaEthernetGrpReactTable -> rttMonReactTable The second part defines a collection of statistics resulting from 'ethernetJitter' operation created either manually or automatically. Glossary: CFM - Connection Fault Management DSAP - Domain Service Access Point: A member of a set of SAPs at which a Maintenance Domain is capable of offering connectivity to systems outside the Maintenance Domain. IP SLA - Cisco IOS IP Service Level Agreements IP SLA operation - Refers to the 'ethernetPing' or 'ethernetJitter' operation supported by IP SLA. MEP - Maintenance association End Point: An actively managed CFM entity, associated with a specific DSAP of a service instance, which can generate and receive CFM PDUs and track any responses. maintenance domain - The network or the part of the network for which faults in connectivity are to be managed. The boundary of a Maintenance Domain is defined by a set of DSAPs, each of which can become a point of connectivity to a service instance. Maintenance Domain Name - The identifier, unique over the domain for which CFM is to protect against accidental concatenation of service instances, of a particular Maintenance Domain. RTT - Round Trip Time SAP - Service Access Point at which a service is offered. service instance - A service instance is a set of SAPs, selected from among the DSAPs defining a Maintenance Domain, such that a Data.Request primitive presented to one SAP can result in a Data.Indication primitive occurring at one or more of the other SAPs in the set. It corresponds to a VLAN or an Ethernet Virtual Connection. TLV - Stands for Type, Length, Value, and denotes a method of encoding variable-length and/or optional information in a PDU. TLVs are not aligned to any particular word or octet boundary. TLVs follow each other with no padding between TLVs. VLAN - Virtual Local Area Network: A subset of the active topology of a Bridged Local Area Network. Associated with each VLAN is a VLAN Identifier. REFERENCE: IEEE 802.1ag Draft 6.0 'Virtual Briged Local Area Networks - Amendments 5: Connectivity Fault Management' July 2006" REVISION "201205150000Z" DESCRIPTION "Added new object group ciscoIpSlaEthernetY1731Group. Added new compliance ciscoIpSlaEthernetComplianceRev3, which deprecates ciscoIpSlaEthenetComplianceRev2" REVISION "200801020000Z" DESCRIPTION "Added object ipslaEthernetGrpCtrlEVC and ipslaEthernetGrpCtrlServiceInsType." REVISION "200602080000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 585 } ciscoIpSlaEthernetMIBNotifs OBJECT IDENTIFIER ::= { ciscoIpSlaEthernetMIB 0 } ciscoIpSlaEthernetMIBObjects OBJECT IDENTIFIER ::= { ciscoIpSlaEthernetMIB 1 } ipslaEthernetGrpCtrl OBJECT IDENTIFIER ::= { ciscoIpSlaEthernetMIBObjects 1 } ipslaEthernetStats OBJECT IDENTIFIER ::= { ciscoIpSlaEthernetMIBObjects 2 } ipslaEthernetLatestOper OBJECT IDENTIFIER ::= { ciscoIpSlaEthernetMIBObjects 3 } ipslaEthernetGrpCtrlTable OBJECT-TYPE SYNTAX SEQUENCE OF IpslaEthernetGrpCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains Auto-Ethernet-CFM control data. When a row transition to the 'active' state, the IP SLA agent will discover all the MEPs inside the specified VLAN and maintenance domain and create IP SLA ethernet operations based on the value of ipslaEthernetGrpCtrlRttType for each MEP. All the values in this table will be passed to the corresponding objects in the rttMonCtrlAdminTable and rttMonEchoAdminTable of CISCO-RTTMON-MIB so that each IP SLA Ethernet operation will have the same configuration as specified for Auto-Ethernet-CFM. - Objects in this table - Corresponding objects in rttMonCtrlAdminTable ipslaEthernetGrpCtrlStatus rttMonCtrlAdminStatus ipslaEthernetGrpCtrlRttType rttMonCtrlAdminRttType ipslaEthernetGrpCtrlOwner rttMonCtrlAdminOwner ipslaEthernetGrpCtrlTag rttMonCtrlAdminTag ipslaEthernetGrpCtrlThreshold rttMonCtrlAdminThreshold ipslaEthernetGrpCtrlTimeout rttMonCtrlAdminTimeout - Objects in this table - Corresponding objects in rttMonEchoAdminTable ipslaEthernetGrpCtrlVLAN rttMonEchoAdminTargetVLAN ipslaEthernetGrpCtrlDomainName rttMonEchoAdminTargetDomainName ipslaEthernetGrpCtrlReqDataSize rttMonEchoAdminPktDataRequestSize ipslaEthernetGrpCtrlCOS rttMonEchoAdminEthernetCOS ipslaEthernetGrpCtrlInterval rttMonEchoAdminInterval ipslaEthernetGrpCtrlNumFrames rttMonEchoAdminNumPackets ipslaEthernetGrpCtrlEVC rttMonEchoAdminTargetEVC" ::= { ipslaEthernetGrpCtrl 1 } ipslaEthernetGrpCtrlEntry OBJECT-TYPE SYNTAX IpslaEthernetGrpCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A collection of objects that define a conceptual Auto-Ethernet-CFM control row. The following objects must be specified in order to create this conceptual row. - ipslaEthernetGrpCtrlStatus - ipslaEthernetGrpCtrlRttType The following objects must be specified in order to activate this conceptual row. - ipslaEthernetGrpCtrlVLAN OR - ipslaEthernetGrpCtrlEVC - ipslaEthernetGrpCtrlDomainName - ipslaEthernetGrpSchedulePeriod - ipslaEthernetGrpScheduleRttStartTime This conceptual row can be delete at any time by set the ipslaEthernetGrpCtrlStatus to 'destroy'. When this row is deleted, All the IP SLA operations created by this row will be destroyed." INDEX { ipslaEthernetGrpCtrlIndex } ::= { ipslaEthernetGrpCtrlTable 1 } IpslaEthernetGrpCtrlEntry ::= SEQUENCE { ipslaEthernetGrpCtrlIndex RttMonCtrlIndex, ipslaEthernetGrpCtrlStatus RowStatus, ipslaEthernetGrpCtrlStorageType StorageType, ipslaEthernetGrpCtrlRttType RttMonRttType, ipslaEthernetGrpCtrlOwner SnmpAdminString, ipslaEthernetGrpCtrlTag SnmpAdminString, ipslaEthernetGrpCtrlThreshold Unsigned32, ipslaEthernetGrpCtrlTimeout Unsigned32, ipslaEthernetGrpCtrlProbeList RttMonIdLst, ipslaEthernetGrpCtrlVLAN VlanId, ipslaEthernetGrpCtrlDomainNameType Dot1agCfmMaintDomainNameType, ipslaEthernetGrpCtrlDomainName Dot1agCfmMaintDomainName, ipslaEthernetGrpCtrlReqDataSize Unsigned32, ipslaEthernetGrpCtrlMPIDExLst RttMonIdLst, ipslaEthernetGrpCtrlCOS Layer2Cos, ipslaEthernetGrpCtrlInterval Unsigned32, ipslaEthernetGrpCtrlNumFrames Unsigned32, ipslaEthernetGrpScheduleRttStartTime TimeTicks, ipslaEthernetGrpSchedulePeriod Unsigned32, ipslaEthernetGrpScheduleFrequency Unsigned32, ipslaEthernetGrpCtrlEVC SnmpAdminString, ipslaEthernetGrpCtrlServiceInsType INTEGER } ipslaEthernetGrpCtrlIndex OBJECT-TYPE SYNTAX RttMonCtrlIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates a row in the ipslaEthernetGrpCtrlTable. This value is a pseudo-random number selected by the management station when creating a row via the ipslaEthernetGrpCtrlStatus object. For easy management, user can select range of numbers for different maintenance domain. For instance, the ipslaEthernetGrpCtrlIndex 1-100 will be used for Domain_A, 101-200 will be used for Domain_B. If the pseudo-random number is already in use an 'inconsistentValue' return code will be returned when set operation is attempted." ::= { ipslaEthernetGrpCtrlEntry 1 } ipslaEthernetGrpCtrlStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the status of Auto-Ethernet-CFM control row. Following objects must be specified in order for this object to become active. - ipslaEthernetGrpCtrlRttType - ipslaEthernetGrpCtrlVLAN OR - ipslaEthernetGrpCtrlEVC - ipslaEthernetGrpCtrlServiceInsType - ipslaEthernetGrpCtrlDomainName - ipslaEthernetGrpSchedulePeriod - ipslaEthernetGrpScheduleRttStartTime All other objects can assume default values. The following objects cannot be modified after creating the Auto-Ethernet-CFM conceptual row. - ipslaEthernetGrpCtrlRttType - ipslaEthernetGrpCtrlVLAN OR - ipslaEthernetGrpCtrlEVC - ipslaEthernetGrpCtrlDomainName - ipslaEthernetGrpCtrlServiceInsType The following objects can be modified even after creating the Auto-Ethernet-CFM conceptual row by setting this object to 'notInService' - All other writable objects in ipslaEthernetGrpCtrlTable except ipslaEthernetGrpCtrlRttType, ipslaEthernetGrpCtrlVLAN, ipslaEthernetGrpCtrlDomainName, ipslaEthernetGrpCtrlEVC and ipslaEthernetGrpCtrlServiceInsType - Objects in the ipslaEthernetGrpScheduleTable. The following objects can be modified as needed without setting this object to 'notInService' even after creating the Auto-Ethernet-CFM conceptual row. - Objects in ipslaEthernetGrpReactTable. This object can be set to 'destroy' from any value at any time. When this object is set to 'destroy' it will stop and destroy all the IP SLA operations created by this Auto-Ethernet-CFM before destroying Auto-Ethernet-CFM control row." ::= { ipslaEthernetGrpCtrlEntry 2 } ipslaEthernetGrpCtrlStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies how the SNMP entity stores the data contained by the corresponding conceptual row. This object can be set to either 'volatile' or 'nonVolatile'. Other values are not applicable for this conceptual row and are not supported." DEFVAL { volatile } ::= { ipslaEthernetGrpCtrlEntry 3 } ipslaEthernetGrpCtrlRttType OBJECT-TYPE SYNTAX RttMonRttType MAX-ACCESS read-create STATUS current DESCRIPTION "The type of IP SLA operation to be created by this Auto-Ethernet-CFM. This value can only be set to type 'ethernetPing' and 'ethernetJitter'. 'ethernetPing' operation sends the regular 802.1ag loopback frame to the target MEP to monitor the connectivity and perform delay analysis. 'ethernetJitter'sends multiple enhanced CFM frames at a specified interval to the target MEP to measure metrics such as RTT, jitter, frame loss, one-way latency and so on. This value must be set before setting any other parameter configuration of an Auto-Ethernet-CFM." ::= { ipslaEthernetGrpCtrlEntry 4 } ipslaEthernetGrpCtrlOwner OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..255)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string which used by a managing application to identify the entity that created this Auto-Ethernet-CFM." DEFVAL { "" } ::= { ipslaEthernetGrpCtrlEntry 5 } ipslaEthernetGrpCtrlTag OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..255)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string which used by a managing application to identify the target VLAN and maintenance domain of this Auto-Ethernet-CFM." DEFVAL { "" } ::= { ipslaEthernetGrpCtrlEntry 6 } ipslaEthernetGrpCtrlThreshold OBJECT-TYPE SYNTAX Unsigned32 (0..2147483647) UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the threshold value of a particular object. This value will be examined for each IP SLA operations created by the Auto-Ethernet-CFM. For 'ethernetPing', if the value of rttMonLatestRttOperCompletionTime is greater than this value, the 'overThreshold' will be reported through rttMonLatestRttOperSense defined in CISCO-RTTMON-MIB. For 'ethernetJitter', if the value of ipslaEtherJitterLatestAvgJitter value is greater than this value, the 'overThreshold' will be reported through ipslaEtherJitterLatestSense defined this module." DEFVAL { 5000 } ::= { ipslaEthernetGrpCtrlEntry 7 } ipslaEthernetGrpCtrlTimeout OBJECT-TYPE SYNTAX Unsigned32 (0..604800000) UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the duration to wait for an IP SLA operation created by this Auto-Ethernet-CFM to complete. For 'ethernetPing', if the value of rttMonLatestRttOperCompletionTime is greater than this value, the 'timeout' will be reported through rttMonLatestRttOperSense defined in CISCO-RTTMON-MIB. For 'ethernetJitter', if all the frames sent to target MEP have not been recievied within this duration, the 'timeout' will be reported through ipslaEtherJitterLatestSense defined this module. The value of this object cannot be set to a value which would specify a duration exceeding ipslaEthernetGrpScheduleFrequency." DEFVAL { 5000 } ::= { ipslaEthernetGrpCtrlEntry 8 } ipslaEthernetGrpCtrlProbeList OBJECT-TYPE SYNTAX RttMonIdLst MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the identifiers of the IP SLA operations that are created by the Auto-Ethernet-CFM. The identifier will be stored in rttMonCtrlAdminIndex defined in CISCO-RTTMON-MIB for each IP SLA operation." ::= { ipslaEthernetGrpCtrlEntry 9 } ipslaEthernetGrpCtrlVLAN OBJECT-TYPE SYNTAX VlanId MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the identifier of VLAN for which the Auto-Ethernet-CFM operation will be used. It is an unique identifier for a service instance within a Maintenance Domain specified by ipslaEthernetGrpCtrlDomainName. The Auto-Ethernet-CFM will find all the MEPs participating in this VLAN and create IP SLA operations for each MEP corresponding to value specified in ipslaEthernetGrpCtrlRttType. The value of this object is in effect only when the value of ipslaEthernetGrpCtrlServiceInsType is set to 'vlan'." ::= { ipslaEthernetGrpCtrlEntry 10 } ipslaEthernetGrpCtrlDomainNameType OBJECT-TYPE SYNTAX Dot1agCfmMaintDomainNameType MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the type of maintenance domain name to be used by the Auto-Ethernet-CFM operation. This object can only be set to the following values: 'none'(1) 'charString'(4) Other values are not supported. Value 'none' means that the ipslaEthernetGrpCtrlDomainName has not been specified." DEFVAL { none } ::= { ipslaEthernetGrpCtrlEntry 11 } ipslaEthernetGrpCtrlDomainName OBJECT-TYPE SYNTAX Dot1agCfmMaintDomainName MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the maintenance domain name to be used by the Auto-Ethernet-CFM operation. The Auto-Ethernet-CFM operation discovers all the MEPs participating in the VLAN specified by ipslaEthernetGrpCtrlVLAN within this maintenance domain and create IP SLA operations for each MEP corresponding to value specified in ipslaEthernetGrpCtrlRttType. As long as the value of this object is specified, the value of ipslaEthernetGrpCtrlDomainNameType must be set to 'charString'." ::= { ipslaEthernetGrpCtrlEntry 12 } ipslaEthernetGrpCtrlReqDataSize OBJECT-TYPE SYNTAX Unsigned32 (0..1400) UNITS "octets" MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the padding that needs to be inserted into each ethernet frame of the IP SLA operation. The total ethernet frame size of the IP SLA operation is: CFM_header + TLVs + si_length + dm_length + padding size where dm_length = number of octets of the maintenance domain name si_length = number of octets of the service instance name CFM_header = 8 octets TLVs = 60 octets for 'ethernetPing' 45 octets for 'ethernetJitter' If the total frame size exceeds 1500, only 1500 will be sent to the target MEP." DEFVAL { 0 } ::= { ipslaEthernetGrpCtrlEntry 13 } ipslaEthernetGrpCtrlMPIDExLst OBJECT-TYPE SYNTAX RttMonIdLst MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the identifiers of the MEPs that will be excluded when create IP SLA operations by Auto-Ethernet-CFM operation." ::= { ipslaEthernetGrpCtrlEntry 14 } ipslaEthernetGrpCtrlCOS OBJECT-TYPE SYNTAX Layer2Cos MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the Class Of Service field in an Ethernet frame header." DEFVAL { 0 } ::= { ipslaEthernetGrpCtrlEntry 15 } ipslaEthernetGrpCtrlInterval OBJECT-TYPE SYNTAX Unsigned32 (1..60000) UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "This value specifies the inter-frame delay between Ethernet frames that need to be transmitted to the target MEPs. This object is applicable to 'ethernetJitter' operation only." DEFVAL { 20 } ::= { ipslaEthernetGrpCtrlEntry 16 } ipslaEthernetGrpCtrlNumFrames OBJECT-TYPE SYNTAX Unsigned32 (1..60000) MAX-ACCESS read-create STATUS current DESCRIPTION "This value specifies the number of Ethernet frames that need to be transmitted to the target MEPs. This object is applicable to 'ethernetJitter' operation only." DEFVAL { 10 } ::= { ipslaEthernetGrpCtrlEntry 17 } ipslaEthernetGrpScheduleRttStartTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the time when this conceptual row will become 'active'. ipslaEthernetGrpSchedulePeriod object must be specified before setting this object. When sysUpTime equals this value, this object will cause the conceptual Auto-Ethernet-CFM row transmit to 'active'and start to discover the existing MEPs. Meanwhile the IP SLA operations will be created for each discovered MEP, and rttMonCtrlAdminStatus of each IP SLA operation will transmit to 'active'. If this object has value as 1, the conceptual Auto-Ethernet-CFM row will transmit to 'active' right now. Value of 0 puts this conceptual row in pending state." DEFVAL { 0 } ::= { ipslaEthernetGrpCtrlEntry 18 } ipslaEthernetGrpSchedulePeriod OBJECT-TYPE SYNTAX Unsigned32 (1..604800) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the time duration over which all the IP SLA operations created by the current Auto-Ethernet-CFM have to be scheduled. For instance, if there are three MEPs discovered, there will be three IP SLA operations created. If this object is set to 30, ipslaEthernetGrpScheduleRttStartTime is set to T, the start time of three operations will be spreaded evenly within 30 seconds, i.e. start time: T+0 -------- T+9 ----------T+19 operation1 operation2 operation3 This object must be set first before setting ipslaEthernetGrpScheduleRttStartTime." ::= { ipslaEthernetGrpCtrlEntry 19 } ipslaEthernetGrpScheduleFrequency OBJECT-TYPE SYNTAX Unsigned32 (1..604800) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the duration between initiating each IP SLA operation created by the Auto-Ethernet-CFM. Take above example, if the ipslaEthernetGrpScheduleFrequency is set to 60, then the start time of each IP SLA operation like: start time: T+0 -------- T+9 ----------T+19----- operation1 operation2 operation3 start again: --T+60-------- T+69 ----------T+79-- operation1 operation2 operation3 start 3rd time:--T+120-------- T+129 ----------T+139-- operation1 operation2 operation3 This object cannot be set to a value which would be a shorter duration than ipslaEthernetGrpCtrlTimeout. The default value of this object is the value set to ipslaEthernetGrpSchedulePeriod. This value will be passed to rttMonCtrlAdminFrequency for all the IP SLA operations created by the Auto-Ethernet-CFM." ::= { ipslaEthernetGrpCtrlEntry 20 } ipslaEthernetGrpCtrlEVC OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..100)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the Ethernet Virtual Connection for which the Auto-Ethernet-CFM operation will be used. It is an unique identifier for a service instance within a Maintenance Domain specified by ipslaEthernetGrpCtrlDomainName. The Auto-Ethernet-CFM will find all the MEPs participating in this Ethernet Virtual Connection and create IP SLA operations for each MEP corresponding to value specified in ipslaEthernetGrpCtrlRttType. The value of this object is in effect only when the value of ipslaEthernetGrpCtrlServiceInsType is set to 'evc'." ::= { ipslaEthernetGrpCtrlEntry 21 } ipslaEthernetGrpCtrlServiceInsType OBJECT-TYPE SYNTAX INTEGER { vlan(1), evc(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the type of service instance to be used by the Auto-Ethernet-CFM operation. When this object is set to value 'vlan', ipslaEthernetGrpCtrlVLAN must be set, and the value of ipslaEthernetGrpCtrlVLAN will be used by the Auto-Ethernet-CFM to discover the participating MEPs. When this object is set to value 'evc', ipslaEthernetGrpCtrlEVC must be set, and the value of ipslaEthernetGrpCtrlEVC will be used by the Auto-Ethernet-CFM to discover the participating MEPs." ::= { ipslaEthernetGrpCtrlEntry 22 } -- Auto-Ethernet-CFM Reaction Table ipslaEthernetGrpReactTable OBJECT-TYPE SYNTAX SEQUENCE OF IpslaEthernetGrpReactEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains the reaction configurations for Auto-Ethernet-CFM operation. The reaction configuration specifies the network perfomance parameter needs to be monitored, the threshold for the parameter, the type of threshold violation that will trigger a reaction, and how to react upon a threshold being violated. This allows for proactive monitoring in an environment where user can be alerted to potential network problems, rather than having to manually examine data. Each conceptual row in ipslaEthernetGrpReactTable corresponds to a reaction configured for a corresponding Auto-Ethernet-CFM operation. Each Auto-Ethernet-CFM operation can have multiple parameters monitored and hence there can be multiple reaction configuration rows for a particular Auto-Ethernet-CFM operation. The reaction configurations in this table for a particular Auto-Ethernet-CFM operation will be passed to the corresponding objects in rttMonReactTable of CISCO-RTTMON-MIB for all the IP SLA operations created by this Auto-Ethernet-CFM. This makes the IP SLA operation capable of reacting to certain measured network condition such as long round trip delay, big jitter, etc., by generating a notification to a network management application based on defined thresholds. - Objects in this table - Corresponding objects in rttMonReactTable ipslaEthernetGrpReactConfigIndex rttMonReactConfigIndex ipslaEthernetGrpReactVar rttMonReactVar ipslaEthernetGrpReactThresholdType rttMonReactThresholdType ipslaEthernetGrpReactThresholdRising rttMonReactThresholdRising ipslaEthernetGrpReactThresholdFalling rttMonReactThresholdFalling ipslaEthernetGrpReactThresholdCountX rttMonReactThresholdCountX ipslaEthernetGrpReactThresholdCountY rttMonReactThresholdCountY ipslaEthernetGrpReactActionType rttMonReactActionType ipslaEthernetGrpReactStatus rttMonReactStatus This table is coupled with ipslaEthernetGrpCtrlTable. When an entry in the ipslaEthernetGrpCtrlTable is destroyed, the corresponding entries in this table will be destroyed too." ::= { ipslaEthernetGrpCtrl 2 } ipslaEthernetGrpReactEntry OBJECT-TYPE SYNTAX IpslaEthernetGrpReactEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A collection of objects that define a conceptual Auto-Ethernet-CFM reaction configuration row. In order to create this conceptual row, ipslaEthernetGrpReactStatus must be set to 'createAndGo' and ipslaEthernetGrpReactVar must be specified. This conceptual row can be deleted at any time by set ipslaEthernetGrpReactStatus to 'destroy'. When this row is deleted, the corresponding reaction configuration of all the IP SLA operations are deleted." INDEX { ipslaEthernetGrpCtrlIndex, ipslaEthernetGrpReactConfigIndex } ::= { ipslaEthernetGrpReactTable 1 } IpslaEthernetGrpReactEntry ::= SEQUENCE { ipslaEthernetGrpReactConfigIndex RttMonCtrlIndex, ipslaEthernetGrpReactStatus RowStatus, ipslaEthernetGrpReactStorageType StorageType, ipslaEthernetGrpReactVar RttMonReactVar, ipslaEthernetGrpReactThresholdType INTEGER, ipslaEthernetGrpReactThresholdRising Unsigned32, ipslaEthernetGrpReactThresholdFalling Unsigned32, ipslaEthernetGrpReactThresholdCountX Unsigned32, ipslaEthernetGrpReactThresholdCountY Unsigned32, ipslaEthernetGrpReactActionType INTEGER } ipslaEthernetGrpReactConfigIndex OBJECT-TYPE SYNTAX RttMonCtrlIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object along with ipslaEthernetGrpCtrlEntry identifies a particular reaction-configuration for a particular Auto-Ethernet-CFM operation. This is a pseudo-random number selected by the management station when creating a row via the ipslaEthernetGrpReactStatus. If the pseudo-random number is already in use an 'inconsistentValue' return code will be returned when set operation is attempted." ::= { ipslaEthernetGrpReactEntry 1 } ipslaEthernetGrpReactStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This objects specifies the status of the conceptual Auto-Ethernet-CFM reaction control row. Only 'createAndGo' and 'destroy' operations are permitted on the row. In order for this object to become 'active', ipslaEthernetGrpReactVar must be defined. All other objects assume the default value. When this object is in 'active' state, all the writable objects except ipslaEthernetGrpReactVar can be modified. When this object moves to 'active' state, the rttMonReactStatus of the individual IP SLA operations moves to 'active' state, thus the performance parameter specified in the reaction configuration is monitored for each IP SLA operation and the notifications are generated when the threshold violation takes place. This object can be set to 'destroy' from any value at any time. When this object is set to 'destroy', the reaction configuration of both Auto-Ethernet-CFM operation and IP SLA operations are removed." ::= { ipslaEthernetGrpReactEntry 2 } ipslaEthernetGrpReactStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies how the SNMP entity stores the data contained by the corresponding conceptual row. This object can be set to either 'volatile' or 'nonVolatile'. Other values are not applicable for this conceptual row and are not supported." DEFVAL { volatile } ::= { ipslaEthernetGrpReactEntry 3 } ipslaEthernetGrpReactVar OBJECT-TYPE SYNTAX RttMonReactVar MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the performance parameter that will be monitored by the IP SLA operations which are created via Auto-Ethernet-CFM operation. The performance parameters that are valid to both 'ethernetJitter' and 'ethernetPing' include: - 'connectionLoss' - 'rtt' - 'timeout' The performance parameters that are only valid to 'ethernetJitter' include: - 'jitterSDAvg' - 'jitterDSAvg' - 'jitterAvg' - 'maxOfPositiveSD' - 'maxOfNegativeSD' - 'maxOfPositiveDS' - 'maxOfNegativeDS' - 'packetLateArrival' - 'packetLossDS' - 'packetLossSD' - 'packetOutOfSequence' - 'packetMIA'" ::= { ipslaEthernetGrpReactEntry 4 } ipslaEthernetGrpReactThresholdType OBJECT-TYPE SYNTAX INTEGER { never(1), immediate(2), consecutive(3), xOfy(4), average(5) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the type of threshold violation that will trigger an notification. The notification will be sent accordingly only when the object rttMonReactOccurred which is defined in CISCO-RTTMON-MIB for IP SLA operation is set to 'true' or 'false'. 'never' - rttMonReactOccurred is never set 'immediate' - rttMonReactOccurred is set to 'true' when the value of parameter for which reaction is configured ( e.g. rtt, jitterAvg) violates the threshold. Conversely, rttMonReactOccurred is set to 'false' when the parameter ( e.g. rtt, jitterAvg) is below the threshold limits. 'consecutive'- rttMonReactOccurred is set to true when the value of parameter for which reaction is configured ( e.g. rtt, jitterAvg) violates the threshold for configured consecutive times. Conversely, rttMonReactOccurred is set to false when the value of parameter ( e.g. rtt, jitterAvg) is below the threshold limits for the same number of consecutive operations. 'xOfy' - rttMonReactOccurred is set to true when x ( as specified by ipslaEthernetGrpReactThresholdCountX ) out of the last y ( as specified by ipslaEthernetGrpReactThresholdCountY ) times the value of parameter for which the reaction is configured ( e.g. rtt, jitterAvg) violates the threshold. Conversely, it is set to false when x, out of the last y times the value of parameter ( e.g. rtt, jitterAvg) is below the threshold limits. 'average' - rttMonReactOccurred is set to true when the average (ipslaEthernetGrpReactThresholdCountX times ) value of parameter for which reaction is configured ( e.g. rtt, jitterAvg) violates the threshold condition. Conversely, it is set to false when the average value of parameter ( e.g. rtt, jitterAvg)." DEFVAL { never } ::= { ipslaEthernetGrpReactEntry 5 } ipslaEthernetGrpReactThresholdRising OBJECT-TYPE SYNTAX Unsigned32 (0..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the higher threshold limit. If the value of monitored parameter ( e.g rtt, jitterAvg, packetLossSD etc ) rises above this limit and if the condition specified in ipslaEthernetGrpReactThresholdType are satisfied, a notification is generated. Default value of ipslaEthernetGrpReactThresholdRising for 'rtt' is 5000. 'jitterAvg' is 100. 'jitterSDAvg' is 100. 'jitterDSAvg' is 100. 'maxOfPositiveSD' is 10000. 'maxOfNegativeSD' is 10000. 'maxOfPositiveDS' is 10000. 'maxOfNegativeDS' is 10000. 'packetLossSD' is 10000. 'packetLossDS' is 10000. 'packetMIA' is 10000. 'packetLateArrival' is 10000. 'packetOutOfSequence' is 10000. This object is not applicable if the ipslaEthernetGrpReactVar is 'timeout' or 'connectionLoss'. For 'timeout' and 'connectionLoss', the default value will be 0." ::= { ipslaEthernetGrpReactEntry 6 } ipslaEthernetGrpReactThresholdFalling OBJECT-TYPE SYNTAX Unsigned32 (0..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the lower threshold limit. If the value of monitored parameter ( e.g rtt, jitterAvg, packetLossSD etc ) falls below this limit and if the condition specified in ipslaEthernetGrpReactThresholdType are satisfied, a notification is generated. Default value of ipslaEthernetGrpReactThresholdFalling for 'rtt' is 3000. 'jitterAvg' is 100. 'jitterSDAvg' is 100. 'jitterDSAvg' is 100. 'maxOfPositiveSD' is 10000. 'maxOfNegativeSD' is 10000. 'maxOfPositiveDS' is 10000. 'maxOfNegativeDS' is 10000. 'packetLossSD' is 10000. 'packetLossDS' is 10000. 'packetMIA' is 10000. 'packetLateArrival' is 10000. 'packetOutOfSequence' is 10000. This object is not applicable if the ipslaEthernetGrpReactVar is 'timeout' or 'connectionLoss'. For 'timeout' and 'connectionLoss', the default value will be 0." ::= { ipslaEthernetGrpReactEntry 7 } ipslaEthernetGrpReactThresholdCountX OBJECT-TYPE SYNTAX Unsigned32 (1..16) MAX-ACCESS read-create STATUS current DESCRIPTION "If ipslaEthernetGrpReactThresholdType value is 'xOfy', this object specifies the 'x' value. If ipslaEthernetGrpReactThresholdType value is 'consecutive', this object specifies the number of consecutive occurrences that needs threshold violation before setting rttMonReactOccurred as 'true'. If ipslaEthernetGrpReactThresholdType value is 'average', this object specifies the number of samples that needs be considered for calculating average. This object has no meaning if ipslaEthernetGrpReactThresholdType has value of 'never' and 'immediate'." DEFVAL { 5 } ::= { ipslaEthernetGrpReactEntry 8 } ipslaEthernetGrpReactThresholdCountY OBJECT-TYPE SYNTAX Unsigned32 (1..16) MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the 'y' value of the xOfy condition if ipslaEthernetGrpReactThresholdType is 'xOfy'. For other values of ipslaEthernetGrpReactThresholdType, this object is not applicable." DEFVAL { 5 } ::= { ipslaEthernetGrpReactEntry 9 } ipslaEthernetGrpReactActionType OBJECT-TYPE SYNTAX INTEGER { none(1), notification(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies what type of reaction to generate if an IP SLA operation violates one of the watched conditions (specified in ipslaEthernetGrpReactVar): 'none' - no reaction is generated. 'notification' - a notification is generated." DEFVAL { none } ::= { ipslaEthernetGrpReactEntry 10 } -- LatestEthernetJitterOper Table ipslaEtherJitterLatestStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF IpslaEtherJitterLatestStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The 'ethernetJitter' operation sends out frames at the frequency specified by rttMonCtrlAdminFrequency. This table contains the statistics calculated for the latest sent frames. Each conceptual row in this table corresponds to an 'ethernetJitter' operation defined in rttMonCtrlAdminTable and has same index as rttMonCtrlAdminTable." ::= { ipslaEthernetLatestOper 1 } ipslaEtherJitterLatestStatsEntry OBJECT-TYPE SYNTAX IpslaEtherJitterLatestStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A collection of objects that record the latest Ethernet jitter operation. An entry is created only when the following objects are valid. - rttMonCtrlAdminRttType - rttMonEchoAdminProtocol The entry will start to collect data when rttMonCtrlAdminStatus is in 'active' state. The entry will be removed when the rttMonCtrlAdminStatus is changed to 'destroy' state." INDEX { rttMonCtrlAdminIndex } ::= { ipslaEtherJitterLatestStatsTable 1 } IpslaEtherJitterLatestStatsEntry ::= SEQUENCE { ipslaEtherJitterLatestNumRTT Gauge32, ipslaEtherJitterLatestRTTSum Gauge32, ipslaEtherJitterLatestRTTSum2 Gauge32, ipslaEtherJitterLatestRTTMin Gauge32, ipslaEtherJitterLatestRTTMax Gauge32, ipslaEtherJitterLatestMinPosSD Gauge32, ipslaEtherJitterLatestMaxPosSD Gauge32, ipslaEtherJitterLatestNumPosSD Gauge32, ipslaEtherJitterLatestSumPosSD Gauge32, ipslaEtherJitterLatestSum2PosSD Gauge32, ipslaEtherJitterLatestMinNegSD Gauge32, ipslaEtherJitterLatestMaxNegSD Gauge32, ipslaEtherJitterLatestNumNegSD Gauge32, ipslaEtherJitterLatestSumNegSD Gauge32, ipslaEtherJitterLatestSum2NegSD Gauge32, ipslaEtherJitterLatestMinPosDS Gauge32, ipslaEtherJitterLatestMaxPosDS Gauge32, ipslaEtherJitterLatestNumPosDS Gauge32, ipslaEtherJitterLatestSumPosDS Gauge32, ipslaEtherJitterLatestSum2PosDS Gauge32, ipslaEtherJitterLatestMinNegDS Gauge32, ipslaEtherJitterLatestMaxNegDS Gauge32, ipslaEtherJitterLatestNumNegDS Gauge32, ipslaEtherJitterLatestSumNegDS Gauge32, ipslaEtherJitterLatestSum2NegDS Gauge32, ipslaEtherJitterLatestFrmLossSD Gauge32, ipslaEtherJitterLatestFrmLossDS Gauge32, ipslaEtherJitterLatestFrmOutSeq Gauge32, ipslaEtherJitterLatestFrmMIA Gauge32, ipslaEtherJitterLatestFrmSkipped Gauge32, ipslaEtherJitterLatestSense RttResponseSense, ipslaEtherJitterLatestFrmLateA Gauge32, ipslaEtherJitterLatestMinSucFrmL Gauge32, ipslaEtherJitterLatestMaxSucFrmL Gauge32, ipslaEtherJitterLatestOWSumSD Gauge32, ipslaEtherJitterLatestOWSum2SD Gauge32, ipslaEtherJitterLatestOWMinSD Gauge32, ipslaEtherJitterLatestOWMaxSD Gauge32, ipslaEtherJitterLatestOWSumDS Gauge32, ipslaEtherJitterLatestOWSum2DS Gauge32, ipslaEtherJitterLatestOWMinDS Gauge32, ipslaEtherJitterLatestOWMaxDS Gauge32, ipslaEtherJitterLatestNumOW Gauge32, ipslaEtherJitterLatestAvgJitter Gauge32, ipslaEtherJitterLatestAvgSDJ Gauge32, ipslaEtherJitterLatestAvgDSJ Gauge32, ipslaEtherJitterLatestOWAvgSD Gauge32, ipslaEtherJitterLatestOWAvgDS Gauge32, ipslaEtherJitterLatestIAJOut Gauge32, ipslaEtherJitterLatestIAJIn Gauge32, ipslaEtherJLatestFrmUnProcessed Gauge32 } ipslaEtherJitterLatestNumRTT OBJECT-TYPE SYNTAX Gauge32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RTT's that were successfully measured." ::= { ipslaEtherJitterLatestStatsEntry 1 } ipslaEtherJitterLatestRTTSum OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of RTT's that are successfully measured. The number of successfully measured RTT is stored in ipslaEtherJitterLatestNumRTT." ::= { ipslaEtherJitterLatestStatsEntry 2 } ipslaEtherJitterLatestRTTSum2 OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of squares of RTT's that are successfully measured." ::= { ipslaEtherJitterLatestStatsEntry 3 } ipslaEtherJitterLatestRTTMin OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum of RTT's that were successfully measured." ::= { ipslaEtherJitterLatestStatsEntry 4 } ipslaEtherJitterLatestRTTMax OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum of RTT's that were successfully measured." ::= { ipslaEtherJitterLatestStatsEntry 5 } ipslaEtherJitterLatestMinPosSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum of all positive jitter values for frames sent from source to destination." ::= { ipslaEtherJitterLatestStatsEntry 6 } ipslaEtherJitterLatestMaxPosSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum of all positive jitter values for frames sent from source to destination." ::= { ipslaEtherJitterLatestStatsEntry 7 } ipslaEtherJitterLatestNumPosSD OBJECT-TYPE SYNTAX Gauge32 UNITS "occurrences" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of all positive jitter values for frames sent from source to destination." ::= { ipslaEtherJitterLatestStatsEntry 8 } ipslaEtherJitterLatestSumPosSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of all positive jitter values for frames sent source to destination. The number of such values is stored in ipslaEtherJitterLatestNumPosSD." ::= { ipslaEtherJitterLatestStatsEntry 9 } ipslaEtherJitterLatestSum2PosSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of square of all positive jitter values for frames sent from source to destination." ::= { ipslaEtherJitterLatestStatsEntry 10 } ipslaEtherJitterLatestMinNegSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum of absolute values of all negative jitter values for frames sent from source to destination." ::= { ipslaEtherJitterLatestStatsEntry 11 } ipslaEtherJitterLatestMaxNegSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum of absolute values of all negative jitter values for frames sent from source to destination." ::= { ipslaEtherJitterLatestStatsEntry 12 } ipslaEtherJitterLatestNumNegSD OBJECT-TYPE SYNTAX Gauge32 UNITS "occurrences" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of all negative jitter values for frames sent from source to destination." ::= { ipslaEtherJitterLatestStatsEntry 13 } ipslaEtherJitterLatestSumNegSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of all negative jitter values for frames sent from source to destination. The number of such values is stored in ipslaEtherJitterLatestNumNegSD." ::= { ipslaEtherJitterLatestStatsEntry 14 } ipslaEtherJitterLatestSum2NegSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of square of all negative jitter values for frames sent from source to destination." ::= { ipslaEtherJitterLatestStatsEntry 15 } ipslaEtherJitterLatestMinPosDS OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum of all positive jitter values for frames sent from destination to source." ::= { ipslaEtherJitterLatestStatsEntry 16 } ipslaEtherJitterLatestMaxPosDS OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum of all positive jitter values for frames sent from destination to source." ::= { ipslaEtherJitterLatestStatsEntry 17 } ipslaEtherJitterLatestNumPosDS OBJECT-TYPE SYNTAX Gauge32 UNITS "occurrences" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of all positive jitter values for frames sent from destination to source." ::= { ipslaEtherJitterLatestStatsEntry 18 } ipslaEtherJitterLatestSumPosDS OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of all positive jitter values for frames sent from destination to source. The number of such values is stored in ipslaEtherJitterLatestNumPosDS." ::= { ipslaEtherJitterLatestStatsEntry 19 } ipslaEtherJitterLatestSum2PosDS OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of squares of all positive jitter values for frames sent from destination to source." ::= { ipslaEtherJitterLatestStatsEntry 20 } ipslaEtherJitterLatestMinNegDS OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum of all negative jitter values for frames sent from destination to source." ::= { ipslaEtherJitterLatestStatsEntry 21 } ipslaEtherJitterLatestMaxNegDS OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum of all negative jitter values for frames sent from destination to source." ::= { ipslaEtherJitterLatestStatsEntry 22 } ipslaEtherJitterLatestNumNegDS OBJECT-TYPE SYNTAX Gauge32 UNITS "occurrences" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of all negative jitter values for frames sent from destination to source." ::= { ipslaEtherJitterLatestStatsEntry 23 } ipslaEtherJitterLatestSumNegDS OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of all negative jitter values for frames sent from destination to source. The number of such values is stored in ipslaEtherJitterLatestNumNegDS." ::= { ipslaEtherJitterLatestStatsEntry 24 } ipslaEtherJitterLatestSum2NegDS OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of squares of all negative jitter values for frames sent from destination to source." ::= { ipslaEtherJitterLatestStatsEntry 25 } ipslaEtherJitterLatestFrmLossSD OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of frames lost when sent from source to destination." ::= { ipslaEtherJitterLatestStatsEntry 26 } ipslaEtherJitterLatestFrmLossDS OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of frames lost when sent from destination to source." ::= { ipslaEtherJitterLatestStatsEntry 27 } ipslaEtherJitterLatestFrmOutSeq OBJECT-TYPE SYNTAX Gauge32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of frames arrived out of sequence." ::= { ipslaEtherJitterLatestStatsEntry 28 } ipslaEtherJitterLatestFrmMIA OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of frames that are lost for which we cannot determine the direction." ::= { ipslaEtherJitterLatestStatsEntry 29 } ipslaEtherJitterLatestFrmSkipped OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of frames in the operation that could not be initiated due to an internal error." ::= { ipslaEtherJitterLatestStatsEntry 30 } ipslaEtherJitterLatestSense OBJECT-TYPE SYNTAX RttResponseSense MAX-ACCESS read-only STATUS current DESCRIPTION "An application specific sense code for the completion status." ::= { ipslaEtherJitterLatestStatsEntry 31 } ipslaEtherJitterLatestFrmLateA OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of frames that arrived after the timeout." ::= { ipslaEtherJitterLatestStatsEntry 32 } ipslaEtherJitterLatestMinSucFrmL OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum number of frames that are dropped successively." ::= { ipslaEtherJitterLatestStatsEntry 33 } ipslaEtherJitterLatestMaxSucFrmL OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of frames that are dropped successively." ::= { ipslaEtherJitterLatestStatsEntry 34 } ipslaEtherJitterLatestOWSumSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of one way trip time from source to destination." ::= { ipslaEtherJitterLatestStatsEntry 35 } ipslaEtherJitterLatestOWSum2SD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of squares of one way trip time from source to destination." ::= { ipslaEtherJitterLatestStatsEntry 36 } ipslaEtherJitterLatestOWMinSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum of all one way trip time from source to destination." ::= { ipslaEtherJitterLatestStatsEntry 37 } ipslaEtherJitterLatestOWMaxSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum of all one way trip time from source to destination." ::= { ipslaEtherJitterLatestStatsEntry 38 } ipslaEtherJitterLatestOWSumDS OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of one way trip time from destination to source." ::= { ipslaEtherJitterLatestStatsEntry 39 } ipslaEtherJitterLatestOWSum2DS OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of squares of one way trip time from destination to source." ::= { ipslaEtherJitterLatestStatsEntry 40 } ipslaEtherJitterLatestOWMinDS OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum of all one way trip time from destination to source." ::= { ipslaEtherJitterLatestStatsEntry 41 } ipslaEtherJitterLatestOWMaxDS OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum of all one way trip time from destination to source." ::= { ipslaEtherJitterLatestStatsEntry 42 } ipslaEtherJitterLatestNumOW OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of successful one way trip time measurements." ::= { ipslaEtherJitterLatestStatsEntry 43 } ipslaEtherJitterLatestAvgJitter OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The average of positive and negative jitter values in Source-to-Destination and Destination-to-Source direction." ::= { ipslaEtherJitterLatestStatsEntry 44 } ipslaEtherJitterLatestAvgSDJ OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The average of positive and negative jitter values from source to destination." ::= { ipslaEtherJitterLatestStatsEntry 45 } ipslaEtherJitterLatestAvgDSJ OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The average of positive and negative jitter values from destination to source." ::= { ipslaEtherJitterLatestStatsEntry 46 } ipslaEtherJitterLatestOWAvgSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The average one way trip time from source to destination." ::= { ipslaEtherJitterLatestStatsEntry 47 } ipslaEtherJitterLatestOWAvgDS OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The average one way trip time from destination to source." ::= { ipslaEtherJitterLatestStatsEntry 48 } ipslaEtherJitterLatestIAJOut OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Inter-arrival jitter (RFC 1889) at responder." REFERENCE "Refer to the following documents for the definition: RFC 1889, Section 6.3.1" ::= { ipslaEtherJitterLatestStatsEntry 49 } ipslaEtherJitterLatestIAJIn OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Inter-arrival jitter (RFC 1889) at source." REFERENCE "Refer to the following documents for the definition: RFC 1889, Section 6.3.1" ::= { ipslaEtherJitterLatestStatsEntry 50 } ipslaEtherJLatestFrmUnProcessed OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of frames in the operation that could not be processed due to high CPU load." ::= { ipslaEtherJitterLatestStatsEntry 51 } -- Ethernet Jitter Statistics Table ipslaEtherJitterAggStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF IpslaEtherJitterAggStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The 'ethernetJitter' statistics table contains summarized information of the results for a conceptual control row. A rolling accumulated history of this information is maintained in a series of hourly 'group(s)'. When ipslaEtherJAggStatsStartTimeId groups exceeds the rttMonStatisticsAdminNumHourGroups value, the oldest corresponding hourly group will be deleted and will be replaced with the new ipslaEtherJAggStatsStartTimeId hourly group." ::= { ipslaEthernetStats 1 } ipslaEtherJitterAggStatsEntry OBJECT-TYPE SYNTAX IpslaEtherJitterAggStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry contains the objects which accumulate the results of a series of 'ethernetJitter' operations over a 60 minute time period or a time period stored in rttMonScheduleAdminRttLife, whichever is smaller. An entry is created only if when the following objects are valid. - rttMonCtrlAdminRttType - rttMonEchoAdminProtocol The entry will start to collect data when rttMonCtrlAdminStatus is in 'active' state. The entry will be removed when the rttMonCtrlAdminStatus is changed to 'destroy' state." INDEX { rttMonCtrlAdminIndex, ipslaEtherJAggStatsStartTimeId } ::= { ipslaEtherJitterAggStatsTable 1 } IpslaEtherJitterAggStatsEntry ::= SEQUENCE { ipslaEtherJAggStatsStartTimeId TimeStamp, ipslaEtherJAggMeasuredCmpletions Counter32, ipslaEtherJAggMeasuredOvThrshlds Counter32, ipslaEtherJAggMeasuredNumRTTs Counter32, ipslaEtherJAggMeasuredRTTSums Counter32, ipslaEtherJAggMeasuredRTTSum2Ls Counter32, ipslaEtherJAggMeasuredRTTSum2Hs Counter32, ipslaEtherJAggMeasuredRTTMin Gauge32, ipslaEtherJAggMeasuredRTTMax Gauge32, ipslaEtherJAggMeasuredMinPosSD Gauge32, ipslaEtherJAggMeasuredMaxPosSD Gauge32, ipslaEtherJAggMeasuredNumPosSDs Counter32, ipslaEtherJAggMeasuredSumPosSDs Counter32, ipslaEtherJAggMeasuredSum2PSDLs Counter32, ipslaEtherJAggMeasuredSum2PSDHs Counter32, ipslaEtherJAggMeasuredMinNegSD Gauge32, ipslaEtherJAggMeasuredMaxNegSD Gauge32, ipslaEtherJAggMeasuredNumNegSDs Counter32, ipslaEtherJAggMeasuredSumNegSDs Counter32, ipslaEtherJAggMeasuredSum2NSDLs Counter32, ipslaEtherJAggMeasuredSum2NSDHs Counter32, ipslaEtherJAggMeasuredMinPosDS Gauge32, ipslaEtherJAggMeasuredMaxPosDS Gauge32, ipslaEtherJAggMeasuredNumPosDSes Counter32, ipslaEtherJAggMeasuredSumPosDSes Counter32, ipslaEtherJAggMeasuredSum2PDSLs Counter32, ipslaEtherJAggMeasuredSum2PDSHs Counter32, ipslaEtherJAggMeasuredMinNegDS Gauge32, ipslaEtherJAggMeasuredMaxNegDS Gauge32, ipslaEtherJAggMeasuredNumNegDSes Counter32, ipslaEtherJAggMeasuredSumNegDSes Counter32, ipslaEtherJAggMeasuredSum2NDSLs Counter32, ipslaEtherJAggMeasuredSum2NDSHs Counter32, ipslaEtherJAggMeasuredFrmLossSDs Counter32, ipslaEtherJAggMeasuredFrmLssDSes Counter32, ipslaEtherJAggMeasuredFrmOutSeqs Counter32, ipslaEtherJAggMeasuredFrmMIAes Counter32, ipslaEtherJAggMeasuredFrmSkippds Counter32, ipslaEtherJAggMeasuredErrors Counter32, ipslaEtherJAggMeasuredBusies Counter32, ipslaEtherJAggMeasuredOWSumSDs Counter32, ipslaEtherJAggMeasuredOWSum2SDLs Counter32, ipslaEtherJAggMeasuredOWSum2SDHs Counter32, ipslaEtherJAggMeasuredOWMinSD Gauge32, ipslaEtherJAggMeasuredOWMaxSD Gauge32, ipslaEtherJAggMeasuredOWSumDSes Counter32, ipslaEtherJAggMeasuredOWSum2DSLs Counter32, ipslaEtherJAggMeasuredOWSum2DSHs Counter32, ipslaEtherJAggMeasuredOWMinDS Gauge32, ipslaEtherJAggMeasuredOWMaxDS Gauge32, ipslaEtherJAggMeasuredNumOWs Counter32, ipslaEtherJAggMeasuredAvgJ Gauge32, ipslaEtherJAggMeasuredAvgJSD Gauge32, ipslaEtherJAggMeasuredAvgJDS Gauge32, ipslaEtherJAggMinSucFrmLoss Gauge32, ipslaEtherJAggMaxSucFrmLoss Gauge32, ipslaEtherJAggMeasuredIAJOut Gauge32, ipslaEtherJAggMeasuredIAJIn Gauge32, ipslaEtherJAggMeasuredFrmLateAs Counter32, ipslaEtherJAggMeasuredFrmUnPrcds Counter32, ipslaEtherJAggMeasuredMaxPosTW Gauge32, ipslaEtherJAggMeasuredMaxNegTW Gauge32, ipslaEtherJAggMeasuredMinPosTW Gauge32, ipslaEtherJAggMeasuredMinNegTW Gauge32, ipslaEtherJAggMeasuredTxFrmsSD Counter64, ipslaEtherJAggMeasuredTxFrmsDS Counter64, ipslaEtherJAggMeasuredRxFrmsSD Counter64, ipslaEtherJAggMeasuredRxFrmsDS Counter64, ipslaEtherJAggMeasuredMinLossNumeratorSD Gauge32, ipslaEtherJAggMeasuredMinLossDenominatorSD Gauge32, ipslaEtherJAggMeasuredMaxLossNumeratorSD Gauge32, ipslaEtherJAggMeasuredMaxLossDenominatorSD Gauge32, ipslaEtherJAggMeasuredAvgLossNumeratorSD Gauge32, ipslaEtherJAggMeasuredAvgLossDenominatorSD Gauge32, ipslaEtherJAggMeasuredMinLossNumeratorDS Gauge32, ipslaEtherJAggMeasuredMinLossDenominatorDS Gauge32, ipslaEtherJAggMeasuredMaxLossNumeratorDS Gauge32, ipslaEtherJAggMeasuredMaxLossDenominatorDS Gauge32, ipslaEtherJAggMeasuredAvgLossNumeratorDS Gauge32, ipslaEtherJAggMeasuredAvgLossDenominatorDS Gauge32, ipslaEtherJAggMeasuredCumulativeLossNumeratorSD Gauge32, ipslaEtherJAggMeasuredCumulativeLossDenominatorSD Gauge32, ipslaEtherJAggMeasuredCumulativeAvgLossNumeratorSD Gauge32, ipslaEtherJAggMeasuredCumulativeAvgLossDenominatorSD Gauge32, ipslaEtherJAggMeasuredCumulativeLossNumeratorDS Gauge32, ipslaEtherJAggMeasuredCumulativeLossDenominatorDS Gauge32, ipslaEtherJAggMeasuredCumulativeAvgLossNumeratorDS Gauge32, ipslaEtherJAggMeasuredCumulativeAvgLossDenominatorDS Gauge32 } ipslaEtherJAggStatsStartTimeId OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of sysUpTime at the time when this row was created." ::= { ipslaEtherJitterAggStatsEntry 1 } ipslaEtherJAggMeasuredCmpletions OBJECT-TYPE SYNTAX Counter32 UNITS "completions" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Ethernet jitter operations that have completed successfully." ::= { ipslaEtherJitterAggStatsEntry 2 } ipslaEtherJAggMeasuredOvThrshlds OBJECT-TYPE SYNTAX Counter32 UNITS "operations" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Ethernet jitter operations that violate jitterAvg threshold which is defined in RttMonReactVar." ::= { ipslaEtherJitterAggStatsEntry 3 } ipslaEtherJAggMeasuredNumRTTs OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RTTs that are successfully measured." ::= { ipslaEtherJitterAggStatsEntry 4 } ipslaEtherJAggMeasuredRTTSums OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of RTTs that are successfully measured for this ipslaEtherJAggMeasuredStartTimeId hourly group. The number of the successfully measured RTT is stored in the ipslaEtherJAggMeasuredNumRTTs." ::= { ipslaEtherJitterAggStatsEntry 5 } ipslaEtherJAggMeasuredRTTSum2Ls OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of squares of RTTs that are successfully measured (low order 32 bits)." ::= { ipslaEtherJitterAggStatsEntry 6 } ipslaEtherJAggMeasuredRTTSum2Hs OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of squares of RTTs that are successfully measured (high order 32 bits)." ::= { ipslaEtherJitterAggStatsEntry 7 } ipslaEtherJAggMeasuredRTTMin OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum of RTTs that were successfully measured." ::= { ipslaEtherJitterAggStatsEntry 8 } ipslaEtherJAggMeasuredRTTMax OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum of RTTs that were successfully measured." ::= { ipslaEtherJitterAggStatsEntry 9 } ipslaEtherJAggMeasuredMinPosSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum of absolute values of all positive jitter values for frames sent from source to destination." ::= { ipslaEtherJitterAggStatsEntry 10 } ipslaEtherJAggMeasuredMaxPosSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum of absolute values of all positive jitter values for frames sent from source to destination." ::= { ipslaEtherJitterAggStatsEntry 11 } ipslaEtherJAggMeasuredNumPosSDs OBJECT-TYPE SYNTAX Counter32 UNITS "occurrences" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of all positive jitter values for frames sent from source to destination." ::= { ipslaEtherJitterAggStatsEntry 12 } ipslaEtherJAggMeasuredSumPosSDs OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of all positive jitter values for frames sent from source to destination. The number of such values is stored in ipslaEtherJAggMeasuredNumPosSDs." ::= { ipslaEtherJitterAggStatsEntry 13 } ipslaEtherJAggMeasuredSum2PSDLs OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of square of all positive jitter values for frames sent from source to destination (low order 32 bits)." ::= { ipslaEtherJitterAggStatsEntry 14 } ipslaEtherJAggMeasuredSum2PSDHs OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of square of all positive jitter values for frames sent from source to destination (high order 32 bits)." ::= { ipslaEtherJitterAggStatsEntry 15 } ipslaEtherJAggMeasuredMinNegSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum of all negative jitter values for frames sent from source to destination." ::= { ipslaEtherJitterAggStatsEntry 16 } ipslaEtherJAggMeasuredMaxNegSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum of all negative jitter values for frames sent from source to destination." ::= { ipslaEtherJitterAggStatsEntry 17 } ipslaEtherJAggMeasuredNumNegSDs OBJECT-TYPE SYNTAX Counter32 UNITS "occurrences" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of all negative jitter values for frames sent from source to destination." ::= { ipslaEtherJitterAggStatsEntry 18 } ipslaEtherJAggMeasuredSumNegSDs OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of all negative jitter values for frames sent from source to destination. The number of such values is stored in ipslaEtherJAggMeasuredNumNegSDs." ::= { ipslaEtherJitterAggStatsEntry 19 } ipslaEtherJAggMeasuredSum2NSDLs OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of square of all negative jitter values for frames sent from source to destination (low order 32 bits)." ::= { ipslaEtherJitterAggStatsEntry 20 } ipslaEtherJAggMeasuredSum2NSDHs OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of square of all negative jitter values for frames sent from source to destination (high order 32 bits)." ::= { ipslaEtherJitterAggStatsEntry 21 } ipslaEtherJAggMeasuredMinPosDS OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum of all positive jitter values for frames sent from destination to source." ::= { ipslaEtherJitterAggStatsEntry 22 } ipslaEtherJAggMeasuredMaxPosDS OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum of all positive jitter values for frames sent from destination to source." ::= { ipslaEtherJitterAggStatsEntry 23 } ipslaEtherJAggMeasuredNumPosDSes OBJECT-TYPE SYNTAX Counter32 UNITS "occurrences" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of all positive jitter values for frames sent from destination to source." ::= { ipslaEtherJitterAggStatsEntry 24 } ipslaEtherJAggMeasuredSumPosDSes OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of all positive jitter values for frames sent from destination to source. The number of such values is stored in ipslaEtherJAggMeasuredNumPosDSes." ::= { ipslaEtherJitterAggStatsEntry 25 } ipslaEtherJAggMeasuredSum2PDSLs OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of squares of all positive jitter values for frames sent from destination to source (low order 32 bits)." ::= { ipslaEtherJitterAggStatsEntry 26 } ipslaEtherJAggMeasuredSum2PDSHs OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of squares of all positive jitter values for frames sent from destination to source (high order 32 bits)." ::= { ipslaEtherJitterAggStatsEntry 27 } ipslaEtherJAggMeasuredMinNegDS OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum of all negative jitter values for frames sent from destination to source." ::= { ipslaEtherJitterAggStatsEntry 28 } ipslaEtherJAggMeasuredMaxNegDS OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum of all negative jitter values for frames sent from destination to source." ::= { ipslaEtherJitterAggStatsEntry 29 } ipslaEtherJAggMeasuredNumNegDSes OBJECT-TYPE SYNTAX Counter32 UNITS "occurrences" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of all negative jitter values for frames sent from destination to source." ::= { ipslaEtherJitterAggStatsEntry 30 } ipslaEtherJAggMeasuredSumNegDSes OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of all negative jitter values for frames sent from destination to source. The number of such values is stored in ipslaEtherJAggMeasuredNumNegDSes." ::= { ipslaEtherJitterAggStatsEntry 31 } ipslaEtherJAggMeasuredSum2NDSLs OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of squares of all negative jitter values for frames sent from destination to source (low order 32 bits)." ::= { ipslaEtherJitterAggStatsEntry 32 } ipslaEtherJAggMeasuredSum2NDSHs OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of squares of all negative jitter values for frames sent from destination to source (high order 32 bits)." ::= { ipslaEtherJitterAggStatsEntry 33 } ipslaEtherJAggMeasuredFrmLossSDs OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of lost frames when sent from source to destination." ::= { ipslaEtherJitterAggStatsEntry 34 } ipslaEtherJAggMeasuredFrmLssDSes OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of lost frames when sent from destination to source." ::= { ipslaEtherJitterAggStatsEntry 35 } ipslaEtherJAggMeasuredFrmOutSeqs OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of frames arrived out of sequence." ::= { ipslaEtherJitterAggStatsEntry 36 } ipslaEtherJAggMeasuredFrmMIAes OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of frames that are lost for which we cannot determine the direction." ::= { ipslaEtherJitterAggStatsEntry 37 } ipslaEtherJAggMeasuredFrmSkippds OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of frames that are skipped per operation because the router could not send the packet out." ::= { ipslaEtherJitterAggStatsEntry 38 } ipslaEtherJAggMeasuredErrors OBJECT-TYPE SYNTAX Counter32 UNITS "errors" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of occasions when an Ethernet jitter operation could not be initiated because of an internal error." ::= { ipslaEtherJitterAggStatsEntry 39 } ipslaEtherJAggMeasuredBusies OBJECT-TYPE SYNTAX Counter32 UNITS "busies" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of occasions when an Ethernet jitter operation could not be initiated because a previous Ethernet jitter operation has not been completed." ::= { ipslaEtherJitterAggStatsEntry 40 } ipslaEtherJAggMeasuredOWSumSDs OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of one way trip time from source to destination." ::= { ipslaEtherJitterAggStatsEntry 41 } ipslaEtherJAggMeasuredOWSum2SDLs OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of squares of one way trip time from source to destination (low order 32 bits)." ::= { ipslaEtherJitterAggStatsEntry 42 } ipslaEtherJAggMeasuredOWSum2SDHs OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of squares of one way trip time from source to destination (high order 32 bits)." ::= { ipslaEtherJitterAggStatsEntry 43 } ipslaEtherJAggMeasuredOWMinSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum of all one way trip time from source to destination." ::= { ipslaEtherJitterAggStatsEntry 44 } ipslaEtherJAggMeasuredOWMaxSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum of all one way trip time from source to destination." ::= { ipslaEtherJitterAggStatsEntry 45 } ipslaEtherJAggMeasuredOWSumDSes OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of one way trip time from destination to source." ::= { ipslaEtherJitterAggStatsEntry 46 } ipslaEtherJAggMeasuredOWSum2DSLs OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of squares of one way trip time from destination to source (low order 32 bits)." ::= { ipslaEtherJitterAggStatsEntry 47 } ipslaEtherJAggMeasuredOWSum2DSHs OBJECT-TYPE SYNTAX Counter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of squares of one way trip time from destination to source (high order 32 bits)." ::= { ipslaEtherJitterAggStatsEntry 48 } ipslaEtherJAggMeasuredOWMinDS OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum of all one way trip time from destination to source." ::= { ipslaEtherJitterAggStatsEntry 49 } ipslaEtherJAggMeasuredOWMaxDS OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum of all one way trip time from destination to source." ::= { ipslaEtherJitterAggStatsEntry 50 } ipslaEtherJAggMeasuredNumOWs OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of one way trip time that are successfully measured." ::= { ipslaEtherJitterAggStatsEntry 51 } ipslaEtherJAggMeasuredAvgJ OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The average of positive and negative jitter values for source-to-destination and destination-to-source direction." ::= { ipslaEtherJitterAggStatsEntry 52 } ipslaEtherJAggMeasuredAvgJSD OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The average of positive and negative jitter values in source-to-destination direction." ::= { ipslaEtherJitterAggStatsEntry 53 } ipslaEtherJAggMeasuredAvgJDS OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The average of positive and negative jitter values in destination-to-source direction." ::= { ipslaEtherJitterAggStatsEntry 54 } ipslaEtherJAggMinSucFrmLoss OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum number of frames that are dropped successively." ::= { ipslaEtherJitterAggStatsEntry 55 } ipslaEtherJAggMaxSucFrmLoss OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of frames that are dropped successively." ::= { ipslaEtherJitterAggStatsEntry 56 } ipslaEtherJAggMeasuredIAJOut OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Inter-arrival jitter (RFC 1889) at responder" REFERENCE "Refer to the following documents for the definition: RFC 1889, Section 6.3.1" ::= { ipslaEtherJitterAggStatsEntry 57 } ipslaEtherJAggMeasuredIAJIn OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Inter-arrival jitter (RFC 1889) at sender" REFERENCE "Refer to the following documents for the definition: RFC 1889, Section 6.3.1" ::= { ipslaEtherJitterAggStatsEntry 58 } ipslaEtherJAggMeasuredFrmLateAs OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of frames that arrived after the timeout." ::= { ipslaEtherJitterAggStatsEntry 59 } ipslaEtherJAggMeasuredFrmUnPrcds OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of frames that arrived but could not be processed due to the internal error." ::= { ipslaEtherJitterAggStatsEntry 60 } ipslaEtherJAggMeasuredMaxPosTW OBJECT-TYPE SYNTAX Gauge32 UNITS "microseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The two-way maximum of all positive jitter values for frames." ::= { ipslaEtherJitterAggStatsEntry 61 } ipslaEtherJAggMeasuredMaxNegTW OBJECT-TYPE SYNTAX Gauge32 UNITS "microseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The two-way maximum of all negative jitter values for frames." ::= { ipslaEtherJitterAggStatsEntry 62 } ipslaEtherJAggMeasuredMinPosTW OBJECT-TYPE SYNTAX Gauge32 UNITS "microseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The two-way minimum of all positive jitter values for frames." ::= { ipslaEtherJitterAggStatsEntry 63 } ipslaEtherJAggMeasuredMinNegTW OBJECT-TYPE SYNTAX Gauge32 UNITS "microseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The two-way minimum of all negative jitter values for frames." ::= { ipslaEtherJitterAggStatsEntry 64 } ipslaEtherJAggMeasuredTxFrmsSD OBJECT-TYPE SYNTAX Counter64 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of data frames sent from source to destination." ::= { ipslaEtherJitterAggStatsEntry 65 } ipslaEtherJAggMeasuredTxFrmsDS OBJECT-TYPE SYNTAX Counter64 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of data frames sent from destination to source." ::= { ipslaEtherJitterAggStatsEntry 66 } ipslaEtherJAggMeasuredRxFrmsSD OBJECT-TYPE SYNTAX Counter64 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of data frames received from source to destination." ::= { ipslaEtherJitterAggStatsEntry 67 } ipslaEtherJAggMeasuredRxFrmsDS OBJECT-TYPE SYNTAX Counter64 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of data frames received from destination to source." ::= { ipslaEtherJitterAggStatsEntry 68 } ipslaEtherJAggMeasuredMinLossNumeratorSD OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The numerator for the minimum loss ratio recorded in the source to destination direction." ::= { ipslaEtherJitterAggStatsEntry 69 } ipslaEtherJAggMeasuredMinLossDenominatorSD OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The denominator for the minimum loss ratio recorded in the source to destination direction." ::= { ipslaEtherJitterAggStatsEntry 70 } ipslaEtherJAggMeasuredMaxLossNumeratorSD OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The numerator for the maximum loss ratio recorded in the source to destination direction." ::= { ipslaEtherJitterAggStatsEntry 71 } ipslaEtherJAggMeasuredMaxLossDenominatorSD OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The denominator for the maximum loss ratio recorded in the source to destination direction." ::= { ipslaEtherJitterAggStatsEntry 72 } ipslaEtherJAggMeasuredAvgLossNumeratorSD OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The numerator for the average loss ratio recorded in the source to destination direction." ::= { ipslaEtherJitterAggStatsEntry 73 } ipslaEtherJAggMeasuredAvgLossDenominatorSD OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The denominator for the average loss ratio recorded in the source to destination direction." ::= { ipslaEtherJitterAggStatsEntry 74 } ipslaEtherJAggMeasuredMinLossNumeratorDS OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The numerator for the minimum loss ratio recorded in the destination to source direction." ::= { ipslaEtherJitterAggStatsEntry 75 } ipslaEtherJAggMeasuredMinLossDenominatorDS OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The denominator for the minimum loss ratio recorded in the destination to source direction." ::= { ipslaEtherJitterAggStatsEntry 76 } ipslaEtherJAggMeasuredMaxLossNumeratorDS OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The numerator for the maximum loss ratio recorded in the destination to source direction." ::= { ipslaEtherJitterAggStatsEntry 77 } ipslaEtherJAggMeasuredMaxLossDenominatorDS OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The denominator for the maximum loss ratio recorded in the destination to source direction." ::= { ipslaEtherJitterAggStatsEntry 78 } ipslaEtherJAggMeasuredAvgLossNumeratorDS OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The numerator for the average loss ratio recorded in the destination to source direction." ::= { ipslaEtherJitterAggStatsEntry 79 } ipslaEtherJAggMeasuredAvgLossDenominatorDS OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The denominator for the average loss ratio recorded in the destination to source direction." ::= { ipslaEtherJitterAggStatsEntry 80 } ipslaEtherJAggMeasuredCumulativeLossNumeratorSD OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The numerator for the loss ratio recorded in the source to destination direction. This value is cumulative over the period of this interval." ::= { ipslaEtherJitterAggStatsEntry 81 } ipslaEtherJAggMeasuredCumulativeLossDenominatorSD OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The denominator for the loss ratio recorded in the source to destination direction. This value is cumulative over the period of this interval." ::= { ipslaEtherJitterAggStatsEntry 82 } ipslaEtherJAggMeasuredCumulativeAvgLossNumeratorSD OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The numerator for the average loss ratio recorded in the source to destination direction. This value is cumulative over the perios of this interval." ::= { ipslaEtherJitterAggStatsEntry 83 } ipslaEtherJAggMeasuredCumulativeAvgLossDenominatorSD OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The denominator for the average loss ratio recorded in the source to destination direction. This value is cumulative over the period of this interval." ::= { ipslaEtherJitterAggStatsEntry 84 } ipslaEtherJAggMeasuredCumulativeLossNumeratorDS OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The numerator for the loss ratio recorded in the destination to source direction. This value is cumulative over the period of this interval." ::= { ipslaEtherJitterAggStatsEntry 85 } ipslaEtherJAggMeasuredCumulativeLossDenominatorDS OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The denominator for the loss ratio recorded in the destination to source direction. This valued is cumulative over the period of this interval." ::= { ipslaEtherJitterAggStatsEntry 86 } ipslaEtherJAggMeasuredCumulativeAvgLossNumeratorDS OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The numerator for the average loss ratio recorded in the destination to source direction. This value is cumulative over the period of this interval." ::= { ipslaEtherJitterAggStatsEntry 87 } ipslaEtherJAggMeasuredCumulativeAvgLossDenominatorDS OBJECT-TYPE SYNTAX Gauge32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The denominator for the average loss ratio recorded in the destination to source direction. This value is cumulative over the period of this interval." ::= { ipslaEtherJitterAggStatsEntry 88 } -- Conformance Information ciscoIpSlaEthernetMIBConform OBJECT IDENTIFIER ::= { ciscoIpSlaEthernetMIB 2 } ciscoIpSlaEthernetCompliances OBJECT IDENTIFIER ::= { ciscoIpSlaEthernetMIBConform 1 } ciscoIpSlaEthernetMIBGroups OBJECT IDENTIFIER ::= { ciscoIpSlaEthernetMIBConform 2 } -- ciscoIpSlaEthernetCompliance is superceded by -- ciscoIpSlaEthernetComplianceRev2 ciscoIpSlaEthernetCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for (1) Ethernet Jitter operation and statistics" MODULE -- this module MANDATORY-GROUPS { ciscoIpSlaEthernetAutoGroup, ciscoIpSlaEthernetStatsGroup } ::= { ciscoIpSlaEthernetCompliances 1 } ciscoIpSlaEthernetComplianceRev2 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for (1) Ethernet Jitter operation and statistics (2) supporting IP SLA Auto-Ethernet-CFM" MODULE -- this module MANDATORY-GROUPS { ciscoIpSlaEthernetAutoGroup, ciscoIpSlaEthernetStatsGroup } GROUP ciscoIpSlaEthernetAutoEVCGroup DESCRIPTION "ciscoIpSlaEthernetAutoEVCGroup is only mandatory for the devices that support Ethernet CFM with Virtual Connection." ::= { ciscoIpSlaEthernetCompliances 2 } ciscoIpSlaEthernetComplianceRev3 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for (1) Ethernet Jitter operation and statistics (2) supporting IP SLA Y1731" MODULE -- this module MANDATORY-GROUPS { ciscoIpSlaEthernetAutoGroup, ciscoIpSlaEthernetStatsGroup } GROUP ciscoIpSlaEthernetY1731Group DESCRIPTION "ciscoIpSlaEthernetY1731Group is only mandatory for the devices that support Ethernet CFM with Virtual Connection." GROUP ciscoIpSlaEthernetAutoEVCGroup DESCRIPTION "ciscoIpSlaEthernetAutoEVCGroup is only mandatory for devices that support Ethernet CFM with Virtual Connection." ::= { ciscoIpSlaEthernetCompliances 3 } ciscoIpSlaEthernetAutoGroup OBJECT-GROUP OBJECTS { ipslaEthernetGrpCtrlStatus, ipslaEthernetGrpCtrlStorageType, ipslaEthernetGrpCtrlRttType, ipslaEthernetGrpCtrlOwner, ipslaEthernetGrpCtrlTag, ipslaEthernetGrpCtrlThreshold, ipslaEthernetGrpCtrlTimeout, ipslaEthernetGrpCtrlProbeList, ipslaEthernetGrpCtrlVLAN, ipslaEthernetGrpCtrlDomainNameType, ipslaEthernetGrpCtrlDomainName, ipslaEthernetGrpCtrlReqDataSize, ipslaEthernetGrpCtrlMPIDExLst, ipslaEthernetGrpCtrlCOS, ipslaEthernetGrpCtrlInterval, ipslaEthernetGrpCtrlNumFrames, ipslaEthernetGrpReactStatus, ipslaEthernetGrpReactStorageType, ipslaEthernetGrpReactVar, ipslaEthernetGrpReactThresholdType, ipslaEthernetGrpReactThresholdRising, ipslaEthernetGrpReactThresholdFalling, ipslaEthernetGrpReactThresholdCountX, ipslaEthernetGrpReactThresholdCountY, ipslaEthernetGrpReactActionType, ipslaEthernetGrpScheduleRttStartTime, ipslaEthernetGrpSchedulePeriod, ipslaEthernetGrpScheduleFrequency } STATUS current DESCRIPTION "A collection of objects that were added to support Auto-Ethernet-CFM." ::= { ciscoIpSlaEthernetMIBGroups 1 } ciscoIpSlaEthernetStatsGroup OBJECT-GROUP OBJECTS { ipslaEtherJitterLatestNumRTT, ipslaEtherJitterLatestRTTSum, ipslaEtherJitterLatestRTTSum2, ipslaEtherJitterLatestRTTMin, ipslaEtherJitterLatestRTTMax, ipslaEtherJitterLatestMinPosSD, ipslaEtherJitterLatestMaxPosSD, ipslaEtherJitterLatestNumPosSD, ipslaEtherJitterLatestSumPosSD, ipslaEtherJitterLatestSum2PosSD, ipslaEtherJitterLatestMinNegSD, ipslaEtherJitterLatestMaxNegSD, ipslaEtherJitterLatestNumNegSD, ipslaEtherJitterLatestSumNegSD, ipslaEtherJitterLatestSum2NegSD, ipslaEtherJitterLatestMinPosDS, ipslaEtherJitterLatestMaxPosDS, ipslaEtherJitterLatestNumPosDS, ipslaEtherJitterLatestSumPosDS, ipslaEtherJitterLatestSum2PosDS, ipslaEtherJitterLatestMinNegDS, ipslaEtherJitterLatestMaxNegDS, ipslaEtherJitterLatestNumNegDS, ipslaEtherJitterLatestSumNegDS, ipslaEtherJitterLatestSum2NegDS, ipslaEtherJitterLatestFrmLossSD, ipslaEtherJitterLatestFrmLossDS, ipslaEtherJitterLatestFrmOutSeq, ipslaEtherJitterLatestFrmMIA, ipslaEtherJitterLatestFrmSkipped, ipslaEtherJitterLatestSense, ipslaEtherJitterLatestFrmLateA, ipslaEtherJitterLatestMinSucFrmL, ipslaEtherJitterLatestMaxSucFrmL, ipslaEtherJitterLatestOWSumSD, ipslaEtherJitterLatestOWSum2SD, ipslaEtherJitterLatestOWMinSD, ipslaEtherJitterLatestOWMaxSD, ipslaEtherJitterLatestOWSumDS, ipslaEtherJitterLatestOWSum2DS, ipslaEtherJitterLatestOWMinDS, ipslaEtherJitterLatestOWMaxDS, ipslaEtherJitterLatestNumOW, ipslaEtherJitterLatestAvgJitter, ipslaEtherJitterLatestAvgSDJ, ipslaEtherJitterLatestAvgDSJ, ipslaEtherJitterLatestOWAvgSD, ipslaEtherJitterLatestOWAvgDS, ipslaEtherJitterLatestIAJOut, ipslaEtherJitterLatestIAJIn, ipslaEtherJLatestFrmUnProcessed, ipslaEtherJAggMeasuredCmpletions, ipslaEtherJAggMeasuredOvThrshlds, ipslaEtherJAggMeasuredNumRTTs, ipslaEtherJAggMeasuredRTTSums, ipslaEtherJAggMeasuredRTTSum2Ls, ipslaEtherJAggMeasuredRTTSum2Hs, ipslaEtherJAggMeasuredRTTMin, ipslaEtherJAggMeasuredRTTMax, ipslaEtherJAggMeasuredMinPosSD, ipslaEtherJAggMeasuredMaxPosSD, ipslaEtherJAggMeasuredNumPosSDs, ipslaEtherJAggMeasuredSumPosSDs, ipslaEtherJAggMeasuredSum2PSDLs, ipslaEtherJAggMeasuredSum2PSDHs, ipslaEtherJAggMeasuredMinNegSD, ipslaEtherJAggMeasuredMaxNegSD, ipslaEtherJAggMeasuredNumNegSDs, ipslaEtherJAggMeasuredSumNegSDs, ipslaEtherJAggMeasuredSum2NSDLs, ipslaEtherJAggMeasuredSum2NSDHs, ipslaEtherJAggMeasuredMinPosDS, ipslaEtherJAggMeasuredMaxPosDS, ipslaEtherJAggMeasuredNumPosDSes, ipslaEtherJAggMeasuredSumPosDSes, ipslaEtherJAggMeasuredSum2PDSLs, ipslaEtherJAggMeasuredSum2PDSHs, ipslaEtherJAggMeasuredMinNegDS, ipslaEtherJAggMeasuredMaxNegDS, ipslaEtherJAggMeasuredNumNegDSes, ipslaEtherJAggMeasuredSumNegDSes, ipslaEtherJAggMeasuredSum2NDSLs, ipslaEtherJAggMeasuredSum2NDSHs, ipslaEtherJAggMeasuredFrmLossSDs, ipslaEtherJAggMeasuredFrmLssDSes, ipslaEtherJAggMeasuredFrmOutSeqs, ipslaEtherJAggMeasuredFrmMIAes, ipslaEtherJAggMeasuredFrmSkippds, ipslaEtherJAggMeasuredErrors, ipslaEtherJAggMeasuredBusies, ipslaEtherJAggMeasuredOWSumSDs, ipslaEtherJAggMeasuredOWSum2SDLs, ipslaEtherJAggMeasuredOWSum2SDHs, ipslaEtherJAggMeasuredOWMinSD, ipslaEtherJAggMeasuredOWMaxSD, ipslaEtherJAggMeasuredOWSumDSes, ipslaEtherJAggMeasuredOWSum2DSLs, ipslaEtherJAggMeasuredOWSum2DSHs, ipslaEtherJAggMeasuredOWMinDS, ipslaEtherJAggMeasuredOWMaxDS, ipslaEtherJAggMeasuredNumOWs, ipslaEtherJAggMeasuredAvgJ, ipslaEtherJAggMeasuredAvgJSD, ipslaEtherJAggMeasuredAvgJDS, ipslaEtherJAggMinSucFrmLoss, ipslaEtherJAggMaxSucFrmLoss, ipslaEtherJAggMeasuredIAJOut, ipslaEtherJAggMeasuredIAJIn, ipslaEtherJAggMeasuredFrmLateAs, ipslaEtherJAggMeasuredFrmUnPrcds } STATUS current DESCRIPTION "A collection of statistics objects related to Ethernet Jitter Probe." ::= { ciscoIpSlaEthernetMIBGroups 2 } ciscoIpSlaEthernetAutoEVCGroup OBJECT-GROUP OBJECTS { ipslaEthernetGrpCtrlEVC, ipslaEthernetGrpCtrlServiceInsType } STATUS current DESCRIPTION "A collection of objects which provides the support for Auto-Ethernet-CFM ping/jitter operation with Ethernet Virtual Connection." ::= { ciscoIpSlaEthernetMIBGroups 3 } ciscoIpSlaEthernetY1731Group OBJECT-GROUP OBJECTS { ipslaEtherJAggMeasuredMaxPosTW, ipslaEtherJAggMeasuredMaxNegTW, ipslaEtherJAggMeasuredMinPosTW, ipslaEtherJAggMeasuredMinNegTW, ipslaEtherJAggMeasuredTxFrmsSD, ipslaEtherJAggMeasuredTxFrmsDS, ipslaEtherJAggMeasuredRxFrmsSD, ipslaEtherJAggMeasuredRxFrmsDS, ipslaEtherJAggMeasuredMinLossNumeratorSD, ipslaEtherJAggMeasuredMinLossDenominatorSD, ipslaEtherJAggMeasuredMaxLossNumeratorSD, ipslaEtherJAggMeasuredMaxLossDenominatorSD, ipslaEtherJAggMeasuredAvgLossNumeratorSD, ipslaEtherJAggMeasuredAvgLossDenominatorSD, ipslaEtherJAggMeasuredMinLossNumeratorDS, ipslaEtherJAggMeasuredMinLossDenominatorDS, ipslaEtherJAggMeasuredMaxLossNumeratorDS, ipslaEtherJAggMeasuredMaxLossDenominatorDS, ipslaEtherJAggMeasuredAvgLossNumeratorDS, ipslaEtherJAggMeasuredAvgLossDenominatorDS, ipslaEtherJAggMeasuredCumulativeLossNumeratorSD, ipslaEtherJAggMeasuredCumulativeLossDenominatorSD, ipslaEtherJAggMeasuredCumulativeAvgLossNumeratorSD, ipslaEtherJAggMeasuredCumulativeAvgLossDenominatorSD, ipslaEtherJAggMeasuredCumulativeLossNumeratorDS, ipslaEtherJAggMeasuredCumulativeLossDenominatorDS, ipslaEtherJAggMeasuredCumulativeAvgLossNumeratorDS, ipslaEtherJAggMeasuredCumulativeAvgLossDenominatorDS } STATUS current DESCRIPTION "A collection of objects which provides the support for Y1731 operation with Ethernet Virtual Connection." ::= { ciscoIpSlaEthernetMIBGroups 4 } END