-- *********************************************************** -- CISCO-IETF-VRRP-MIB -- -- November 2005, Biao Gao -- -- Copyright (c) 2005 by Cisco Systems, Inc. -- All rights reserved. -- *********************************************************** -- -- This mib was extracted from -- draft-ietf-vrrp-unified-mib-04.txt. In terms of object syntax -- and semantics, the content of this Cisco MIB is the same as -- the corresponding I-D revision. This Cisco MIB is created due -- to the "subject to change" nature of the I-Ds. This Cisco MIB -- may later be deprecated, and the stable RFC, which may replace -- the I-D, may be implemented in its place. CISCO-IETF-VRRP-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Counter32, Integer32, Unsigned32 FROM SNMPv2-SMI TEXTUAL-CONVENTION, RowStatus, MacAddress, TruthValue, TimeStamp, TimeInterval FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF ifIndex FROM IF-MIB InetAddressType, InetAddress FROM INET-ADDRESS-MIB ciscoExperiment FROM CISCO-SMI; ciscoVrrpMIB MODULE-IDENTITY LAST-UPDATED "200511170000Z" ORGANIZATION "Cisco Systems Inc" CONTACT-INFO " Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553 -NETS E-mail: cs-san@cisco.com" DESCRIPTION "This MIB describes objects used for managing Virtual Router Redundancy Protocol (VRRP) over IPv4 and IPv6 protocols. This MIB supports VRRP for IPv4 and IPv6 protocols simultaneously running on a given interface of a router." REVISION "200511170000Z" -- 17 Nov 2005 DESCRIPTION "Ciscoized version of draft-ietf-vrrp-unified-mib-04.txt" ::= { ciscoExperiment 999 } -- -- VRRP MIB Groups -- cVrrpNotifications OBJECT IDENTIFIER ::= { ciscoVrrpMIB 0 } cVrrpOperations OBJECT IDENTIFIER ::= { ciscoVrrpMIB 1 } cVrrpStatistics OBJECT IDENTIFIER ::= { ciscoVrrpMIB 2 } cVrrpConformance OBJECT IDENTIFIER ::= { ciscoVrrpMIB 3 } -- -- Textual Conventions -- CVrId ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "A number which, along with IP version and interface index (IfIndex), serves to uniquely identify a virtual router on a given VRRP router. There is no relationship between VrId value used on a IPv4 interface and VrId value used on IPv6 interface. It is legal to use same VrId value on IPv4 and IPv6 interfaces." SYNTAX Integer32 (1..255) -- -- Start of MIB objects -- cVrrpNotificationCntl OBJECT-TYPE SYNTAX INTEGER { enabled (1), disabled (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether the agent should generate the notifications defined in this MIB module. If the value of this object is 'true', then the notifications are generated. If the value of this object is 'false', then the notifications are not generated." DEFVAL { enabled } ::= { cVrrpOperations 2 } -- -- VRRP Operations Table -- cVrrpOperationsTable OBJECT-TYPE SYNTAX SEQUENCE OF CVrrpOperationsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Unified Operations table for a VRRP router which consists of a sequence (i.e., one or more conceptual rows) of 'vrrpOperationsEntry' items." ::= { cVrrpOperations 7 } cVrrpOperationsEntry OBJECT-TYPE SYNTAX CVrrpOperationsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the cVrrpOperationsTable containing the operational characteristics of a virtual router. On a VRRP router, a given virtual router is identified by a combination of the IP version, VRID and ifIndex. Note that rows in this table can be distinguished on a multi-stacked device running VRRP over IPv4 and IPv6 on the same interface. Rows in the table cannot be modified unless the value of 'cVrrpOperationsState' has transitioned to 'initialize'" INDEX { cVrrpOperationsInetAddrType, cVrrpOperationsVrId, ifIndex } ::= { cVrrpOperationsTable 1 } CVrrpOperationsEntry ::= SEQUENCE { cVrrpOperationsInetAddrType InetAddressType, cVrrpOperationsVrId CVrId, cVrrpOperationsVirtualMacAddr MacAddress, cVrrpOperationsState INTEGER, cVrrpOperationsPriority Integer32, cVrrpOperationsVersion INTEGER, cVrrpOperationsAddrCount Integer32, cVrrpOperationsMasterIpAddr InetAddress, cVrrpOperationsPrimaryIpAddr InetAddress, cVrrpOperationsAdvInterval TimeInterval, cVrrpOperationsPreemptMode TruthValue, cVrrpOperationsAcceptMode TruthValue, cVrrpOperationsUpTime TimeStamp, cVrrpOperationsRowStatus RowStatus } cVrrpOperationsInetAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The type of Internet address of CVrrpOperationsEntry. This value applies to both cVrrpOperationsMasterIpAddr and cVrrpOperationsPrimaryIpAddr." ::= { cVrrpOperationsEntry 1 } cVrrpOperationsVrId OBJECT-TYPE SYNTAX CVrId MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object contains the Virtual Router Identifier (VRID)." ::= { cVrrpOperationsEntry 2 } cVrrpOperationsVirtualMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The virtual MAC address of the virtual router. Although the value of this object can be derived from the 'cVrrpOperationsVrId' object, i.e., 00-00-5E-00-01-(VRID) for IPv4 and 00-00-5E-00-02-(VRID) for IPv6, it is defined so that it is easily obtainable by a management application and can be included in VRRP-related SNMP notifications." ::= { cVrrpOperationsEntry 3 } cVrrpOperationsState OBJECT-TYPE SYNTAX INTEGER { initialize(1), backup(2), master(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current state of the virtual router. This object has three defined values: - `initialize', which indicates that the virtual router is waiting for a startup event. - `backup', which indicates that the virtual router is monitoring the availability of the master router. - `master', which indicates that the virtual router is forwarding packets for IP addresses that are associated with this router." ::= { cVrrpOperationsEntry 4 } cVrrpOperationsPriority OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the priority to be used for the virtual router master election process. Higher values imply higher priority. A priority of '0', although not settable, is sent by the master router to indicate that this router has ceased to participate in VRRP and a backup virtual router should transition to become a new master. A priority of 255 is used for the router that owns the associated IP address(es) for VRRP over IPv4 and hence not settable." DEFVAL { 100 } ::= { cVrrpOperationsEntry 5 } cVrrpOperationsVersion OBJECT-TYPE SYNTAX INTEGER { vrrpv2 (1), vrrpv3 (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object contains the VRRP version on which this VRRP instance is running." ::= { cVrrpOperationsEntry 6 } cVrrpOperationsAddrCount OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of IP addresses that are associated with this virtual router. This number is equal to the number of rows in the cVrrpAssociatedAddrTable that correspond to a given IP version/VRID/ifIndex." ::= { cVrrpOperationsEntry 7 } cVrrpOperationsMasterIpAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The master router's real IP address. This is the IP address listed as the source in VRRP advertisement last received by this virtual router." ::= { cVrrpOperationsEntry 9 } cVrrpOperationsPrimaryIpAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "In the case where there are more than one IP Address (associated IP addresses) for a given `ifIndex', this object is used to specify the IP address that will become the cVrrpOperationsMasterIpAddr', should the virtual router transition from backup state to master." ::= { cVrrpOperationsEntry 10 } cVrrpOperationsAdvInterval OBJECT-TYPE SYNTAX TimeInterval (1..4096) UNITS "centiseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The time interval, in centiseconds, between sending advertisement messages. Only the master router sends VRRP advertisements." DEFVAL { 100} ::= { cVrrpOperationsEntry 11 } cVrrpOperationsPreemptMode OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Controls whether a higher priority virtual router will preempt a lower priority master. If the value of this object is 'true', then the higer priority virtual router will preempt. If the value of this object is 'false', then the higer priority vritual router will not preempt." DEFVAL { true } ::= { cVrrpOperationsEntry 12 } cVrrpOperationsAcceptMode OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Controls whether a virtual router in Master state will accept packets addressed to the address owner's IPv6 address as its own if it is not the IPv6 address owner. If the value of this object is 'true', then the virtual router in Master state will accept. If the value of this object is 'false', then the virtual router in Master state will not accept." DEFVAL { false } ::= { cVrrpOperationsEntry 13 } cVrrpOperationsUpTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "This is the value of the `sysUpTime' object when this virtual router (i.e., the `vrrpOperState') transitioned out of `initialized'." ::= { cVrrpOperationsEntry 14 } cVrrpOperationsRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status variable, used in accordance to installation and removal conventions for conceptual rows. The rowstatus of a currently active row in the cVrrpOperationsTable is constrained by the operational state of the corresponding virtual router. When `cVrrpOperationsRowStatus' is set to active(1), no other objects in the conceptual row can be modified. To create a row in this table, a manager sets this object to either createAndGo(4) or createAndWait(5). Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the `cVrrpOperationsRowStatus' column will be read as notReady(3). In particular, a newly created row cannot be made active(1) until (minimally) the corresponding instance of cVrrpOperationsInetAddrType, cVrrpOperationsVrId and cVrrpOperationsPrimaryIpAddr has been set and there is at least one active row in the `cVrrpAssociatedIpAddrTable' defining an associated IP address. notInService(2) should be used to administratively bring the row down." ::= { cVrrpOperationsEntry 15 } -- -- VRRP Associated Address Table -- cVrrpAssociatedIpAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF CVrrpAssociatedIpAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of addresses associated with this virtual router." ::= { cVrrpOperations 8 } cVrrpAssociatedIpAddrEntry OBJECT-TYPE SYNTAX CVrrpAssociatedIpAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table contains an IP address that is associated with a virtual router. The number of rows for a given IP version, VrID and ifIndex will equal the number of IP addresses associated (e.g., backed up) by the virtual router (equivalent to 'cVrrpOperationsIpAddrCount'). Rows in the table cannot be modified unless the value of `cVrrpOperationsState' has transitioned to `initialize'." INDEX { cVrrpAssociatedInetAddrType, cVrrpOperationsVrId, ifIndex, cVrrpAssociatedIpAddr } ::= { cVrrpAssociatedIpAddrTable 1 } CVrrpAssociatedIpAddrEntry ::= SEQUENCE { cVrrpAssociatedInetAddrType InetAddressType, cVrrpAssociatedIpAddr InetAddress, cVrrpAssociatedIpAddrRowStatus RowStatus } cVrrpAssociatedInetAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The type of Internet address of VrrpAssociatedIpAddrEntry." ::= { cVrrpAssociatedIpAddrEntry 2 } cVrrpAssociatedIpAddr OBJECT-TYPE SYNTAX InetAddress (SIZE(16)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The assigned IP addresses that a virtual router is responsible for backing up." ::= { cVrrpAssociatedIpAddrEntry 3 } cVrrpAssociatedIpAddrRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status variable, used according to installation and removal conventions for conceptual rows. To create a row in this table, a manager sets this object to either createAndGo(4) or createAndWait(5). Setting this object to active(1) results in the addition of an associated address for a virtual router. Setting this object to createAndGo (4) results in creating a new instance of a conceptual row and setting it to active. The value of the other columns cannot be modified when the value of this object is active. Destroying the entry or setting it to destroy(6) removes the associated address from the virtual router. The use of other values is implementation-dependent." ::= { cVrrpAssociatedIpAddrEntry 4 } -- -- VRRP Router Statistics -- cVrrpRouterChecksumErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VRRP packets received with an invalid VRRP checksum value." ::= { cVrrpStatistics 1 } cVrrpRouterVersionErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VRRP packets received with an unknown or unsupported version number." ::= { cVrrpStatistics 2 } cVrrpRouterVrIdErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VRRP packets received with an invalid VRID for this virtual router." ::= { cVrrpStatistics 3 } -- -- VRRP Router Statistics Table -- cVrrpRouterStatisticsTable OBJECT-TYPE SYNTAX SEQUENCE OF CVrrpRouterStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of virtual router statistics." ::= { cVrrpStatistics 5 } cVrrpRouterStatisticsEntry OBJECT-TYPE SYNTAX CVrrpRouterStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table, containing statistics information about a given virtual router." INDEX { cVrrpOperationsInetAddrType, cVrrpOperationsVrId, ifIndex} ::= { cVrrpRouterStatisticsTable 1 } CVrrpRouterStatisticsEntry ::= SEQUENCE { cVrrpStatisticsBecomeMaster Counter32, cVrrpStatisticsAdvertiseRcvd Counter32, cVrrpStatisticsAdvIntervalErrors Counter32, cVrrpStatisticsIpTtlErrors Counter32, cVrrpStatisticsPriZeroPktsRcvd Counter32, cVrrpStatisticsPriZeroPktsSent Counter32, cVrrpStatisticsInvldTypePktsRcvd Counter32, cVrrpStatisticsAddressListErrors Counter32, cVrrpStatisticsPacketLengthErrors Counter32, cVrrpStatisticsDiscontinuityTime TimeStamp, cVrrpStatisticsRefreshRate Unsigned32, cVrrpStatisticsInvalidAuthType Counter32 } cVrrpStatisticsBecomeMaster OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times that this virtual router's state has transitioned to MASTER. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the corresponding instance of cVrrpStatisticsDiscontinuityTime." ::= { cVrrpRouterStatisticsEntry 1 } cVrrpStatisticsAdvertiseRcvd OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VRRP advertisements received by this virtual router. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the corresponding instance of cVrrpStatisticsDiscontinuityTime." ::= { cVrrpRouterStatisticsEntry 2 } cVrrpStatisticsAdvIntervalErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VRRP advertisement packets received for which the advertisement interval is different than the one configured for the local virtual router. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the corresponding instance of cVrrpStatisticsDiscontinuityTime." ::= { cVrrpRouterStatisticsEntry 3 } cVrrpStatisticsIpTtlErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VRRP packets received by the Virtual router with IPv4 TTL (for VRRP over IPv4) or IPv6 Hop Limit (for VRRP over IPv6) not equal to 255. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the corresponding instance of cVrrpStatisticsDiscontinuityTime." ::= { cVrrpRouterStatisticsEntry 4 } cVrrpStatisticsPriZeroPktsRcvd OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VRRP packets received by the virtual router with a priority of '0'. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the corresponding instance of cVrrpStatisticsDiscontinuityTime." ::= { cVrrpRouterStatisticsEntry 5 } cVrrpStatisticsPriZeroPktsSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VRRP packets sent by the virtual router with a priority of '0'. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the corresponding instance of cVrrpStatisticsDiscontinuityTime." ::= { cVrrpRouterStatisticsEntry 6 } cVrrpStatisticsInvldTypePktsRcvd OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of VRRP packets received by the virtual router with an invalid value in the 'type' field. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the corresponding instance of cVrrpStatisticsDiscontinuityTime." ::= { cVrrpRouterStatisticsEntry 7 } cVrrpStatisticsAddressListErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VRRP packets received for which the address list contained in the packets does not match the locally configured list that corresponds to rows in the cVrrpAssociatedAddrTable for the virtual router. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the corresponding instance of cVrrpStatisticsDiscontinuityTime." ::= { cVrrpRouterStatisticsEntry 8 } cVrrpStatisticsPacketLengthErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received with a packet length less than the length of the VRRP header. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the corresponding instance of cVrrpStatisticsDiscontinuityTime." ::= { cVrrpRouterStatisticsEntry 11 } cVrrpStatisticsDiscontinuityTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime on the most recent occasion at which any one or more of this entry's counters suffered a discontinuity. If no such discontinuities have occurred since the last re-initialization of the local management subsystem, then this object contains a zero value." ::= { cVrrpRouterStatisticsEntry 12 } cVrrpStatisticsRefreshRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "milli-seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum reasonable polling interval for this entry. This object provides an indication of the minimum amount of time required to update the counters in this entry." ::= { cVrrpRouterStatisticsEntry 13 } cVrrpStatisticsInvalidAuthType OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received with an unknown authentication type." ::= { cVrrpRouterStatisticsEntry 14 } --- --- Objects used in the notifications --- cVrrpNotificationNewMasterReason OBJECT-TYPE SYNTAX INTEGER { priority (0), preempted (1), masterNoResponse (2) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This indicates the reason for NewMaster notification. Used by cVrrpNotificationNewMaster notification." ::= { cVrrpOperations 9 } cVrrpNotificationProtoErrReason OBJECT-TYPE SYNTAX INTEGER { hopLimitError (0), versionError (1), checksumError (2), vridError(3) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This indicates the reason for protocol error notification. Used by cVrrpNotificationProtoError notification." ::= { cVrrpOperations 10 } cVrrpNotificationNewMaster NOTIFICATION-TYPE OBJECTS { cVrrpOperationsMasterIpAddr, cVrrpNotificationNewMasterReason } STATUS current DESCRIPTION "The newMaster notification indicates that the sending agent has transitioned to 'Master' state." ::= { cVrrpNotifications 1 } cVrrpNotificationProtoError NOTIFICATION-TYPE OBJECTS { cVrrpNotificationProtoErrReason } STATUS current DESCRIPTION "The error notification indicates that the sending agent has encountered the protocol error indicated by the value of cVrrpNotificationProtoErrorReason." ::= { cVrrpNotifications 3 } -- -- Conformance Information -- cVrrpMIBCompliances OBJECT IDENTIFIER ::= { cVrrpConformance 1 } cVrrpMIBGroups OBJECT IDENTIFIER ::= { cVrrpConformance 2 } -- -- Compliance Statements -- cVrrpMIBCompliance2 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for both VRRP for IPv4 and VRRP for IPv6 implementations." MODULE -- this module MANDATORY-GROUPS { cVrrpOperationsGroup, cVrrpStatisticsGroup, cVrrpNotificationInfoGroup, cVrrpNotificationsGroup } OBJECT cVrrpOperationsPriority WRITE-SYNTAX Integer32 (1..255) DESCRIPTION "SETable values are from 1 to 255." ::= { cVrrpMIBCompliances 2 } cVrrpMIBReadOnlyCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The read-only compliance statement for all VRRP implementations VRRP for IPv4 and IPv6." MODULE -- this module MANDATORY-GROUPS { cVrrpOperationsGroup, cVrrpStatisticsGroup, cVrrpNotificationInfoGroup, cVrrpNotificationsGroup } OBJECT cVrrpNotificationCntl MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cVrrpOperationsPriority MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cVrrpOperationsPrimaryIpAddr MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cVrrpOperationsAdvInterval MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cVrrpOperationsRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cVrrpAssociatedIpAddrRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { cVrrpMIBCompliances 3 } -- -- Conformance Groups -- cVrrpOperationsGroup OBJECT-GROUP OBJECTS { cVrrpNotificationCntl, cVrrpOperationsVirtualMacAddr, cVrrpOperationsState, cVrrpOperationsPriority, cVrrpOperationsMasterIpAddr, cVrrpOperationsVersion, cVrrpOperationsAdvInterval, cVrrpOperationsPreemptMode, cVrrpOperationsAcceptMode, cVrrpOperationsUpTime, cVrrpOperationsRowStatus, cVrrpOperationsAddrCount, cVrrpOperationsPrimaryIpAddr, cVrrpAssociatedIpAddrRowStatus } STATUS current DESCRIPTION "Conformance group for VRRP over IPv4 and IPv6 operations." ::= { cVrrpMIBGroups 5 } cVrrpStatisticsGroup OBJECT-GROUP OBJECTS { cVrrpRouterChecksumErrors, cVrrpRouterVersionErrors, cVrrpRouterVrIdErrors, cVrrpStatisticsBecomeMaster, cVrrpStatisticsAdvertiseRcvd, cVrrpStatisticsAdvIntervalErrors, cVrrpStatisticsPriZeroPktsRcvd, cVrrpStatisticsPriZeroPktsSent, cVrrpStatisticsInvldTypePktsRcvd, cVrrpStatisticsIpTtlErrors, cVrrpStatisticsAddressListErrors, cVrrpStatisticsPacketLengthErrors, cVrrpStatisticsDiscontinuityTime, cVrrpStatisticsRefreshRate, cVrrpStatisticsInvalidAuthType } STATUS current DESCRIPTION "Conformance group for VRRP over IPv4 and IPv6 statistics." ::= { cVrrpMIBGroups 6 } cVrrpNotificationInfoGroup OBJECT-GROUP OBJECTS { cVrrpNotificationNewMasterReason, cVrrpNotificationProtoErrReason } STATUS current DESCRIPTION "Conformance group for objects contained in VRRP notifications." ::= { cVrrpMIBGroups 8 } cVrrpNotificationsGroup NOTIFICATION-GROUP NOTIFICATIONS { cVrrpNotificationNewMaster, cVrrpNotificationProtoError } STATUS current DESCRIPTION "The VRRP MIB Notification Group." ::= { cVrrpMIBGroups 9 } END