-- ************************************************************* -- CISCO-IETF-IP-MIB: The MIB module to manage IP & ICMP. -- -- February 2002, Ashwini Dahiya, Rajiv Raghunarayan. -- -- Copyright (c) 2002 by Cisco Systems, Inc. -- All rights reserved. -- ************************************************************* -- -- This mib is based on draft-ietf-ipngwg-rfc2011-update-00.txt. -- In the future, this mib may be removed entirely, or re-implemented -- on short notice. The intent is to eventually update the IP-MIB, -- once the final approved version of -- draft-ietf-ipngwg-rfc2011-update-XX.txt is available, -- and remove this CISCO-IETF-IP-MIB in its entirety. CISCO-IETF-IP-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Unsigned32, Counter32 FROM SNMPv2-SMI PhysAddress, TruthValue, TimeStamp, RowPointer, TEXTUAL-CONVENTION FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF InetAddress, InetAddressType, InetAddressPrefixLength FROM INET-ADDRESS-MIB InterfaceIndex, InterfaceIndexOrZero, ifIndex FROM IF-MIB ciscoExperiment FROM CISCO-SMI; ciscoIetfIpMIB MODULE-IDENTITY LAST-UPDATED "200203040000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems Customer Service Postal: 170 West Tasman Drive San Jose, CA 95134 USA Phone: +1 800 553-NETS Email: cs-ipv6@cisco.com" DESCRIPTION "The MIB module for managing IP and ICMP implementations, but excluding the management of IP routes." REVISION "200203040000Z" DESCRIPTION "The initial version of this MIB module." ::= { ciscoExperiment 86 } ciscoIetfIpMIBObjects OBJECT IDENTIFIER ::= { ciscoIetfIpMIB 1 } -- the IP general group cIp OBJECT IDENTIFIER ::= { ciscoIetfIpMIBObjects 1 } -- the IPv6 specific group cIpv6 OBJECT IDENTIFIER ::= { ciscoIetfIpMIBObjects 2 } -- the ICMP group cIcmp OBJECT IDENTIFIER ::= { ciscoIetfIpMIBObjects 3 } -- -- Textual Conventions -- Ipv6AddrIfIdentifier ::= TEXTUAL-CONVENTION DISPLAY-HINT "2x:" STATUS current DESCRIPTION "This data type is used to model IPv6 address interface identifiers. This is a binary string of up to 8 octets in network byte-order." SYNTAX OCTET STRING (SIZE (0..8)) ScopeId ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A Scope Identifier identifies an instance of a specific scope. The scope identifier MUST disambiguate identical address values. For link-local addresses, the scope identifier will typically be the interface index (ifIndex as defined in the IF-MIB) of the interface on which the address is configured. The scope identifier may contain the special value 0 which refers to the default scope. The default scope may be used in cases where the valid scope identifier is not known (e.g., a management application needs to write a site-local InetAddressIPv6 address without knowing the site identifier value). The default scope SHOULD NOT be used as an easy way out in cases where the scope identifier for a non-global IPv6 address is known." SYNTAX Unsigned32 -- -- Object definitions -- cIpv6Forwarding OBJECT-TYPE SYNTAX INTEGER { forwarding(1), -- acting as a router notForwarding(2) -- NOT acting as a router } MAX-ACCESS read-write STATUS current DESCRIPTION "The indication of whether this entity is acting as an IPv6 router in respect to the forwarding of datagrams received by, but not addressed to, this entity. IPv6 routers forward datagrams. IPv6 hosts do not (except those source-routed via the host)." ::= { cIpv6 1 } cIpv6DefaultHopLimit OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value inserted into the Hop Limit field of the IPv6 header of datagrams originated at this entity, whenever a Hop Limit value is not supplied by the transport layer protocol." ::= { cIpv6 2 } -- -- IPv6 Interface table -- cIpv6InterfaceTable OBJECT-TYPE SYNTAX SEQUENCE OF CIpv6InterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table containing per-interface IPv6-specific information." ::= { cIpv6 3 } cIpv6InterfaceEntry OBJECT-TYPE SYNTAX CIpv6InterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing IPv6-specific information for a given interface." INDEX { cIpv6InterfaceIfIndex } ::= { cIpv6InterfaceTable 1 } CIpv6InterfaceEntry ::= SEQUENCE { cIpv6InterfaceIfIndex InterfaceIndex, cIpv6InterfaceEffectiveMtu Unsigned32, cIpv6InterfaceReasmMaxSize Unsigned32, cIpv6InterfaceIdentifier Ipv6AddrIfIdentifier, cIpv6InterfaceIdentifierLength INTEGER, cIpv6InterfacePhysicalAddress PhysAddress } cIpv6InterfaceIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface for which this row contains IPv6-specific information." ::= { cIpv6InterfaceEntry 1 } cIpv6InterfaceEffectiveMtu OBJECT-TYPE SYNTAX Unsigned32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The size of the largest IPv6 packet which can be sent/received on the interface, specified in octets." ::= { cIpv6InterfaceEntry 2 } cIpv6InterfaceReasmMaxSize OBJECT-TYPE SYNTAX Unsigned32 (0..65535) UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The size of the largest IPv6 datagram which this entity can re-assemble from incoming IPv6 fragmented datagrams received on this interface." ::= { cIpv6InterfaceEntry 3 } cIpv6InterfaceIdentifier OBJECT-TYPE SYNTAX Ipv6AddrIfIdentifier MAX-ACCESS read-write STATUS current DESCRIPTION "The Interface Identifier for this interface that is (at least) unique on the link this interface is attached to. The Interface Identifier is combined with an address prefix to form an interface address. By default, the Interface Identifier is autoconfigured according to the rules of the link type this interface is attached to." ::= { cIpv6InterfaceEntry 4 } cIpv6InterfaceIdentifierLength OBJECT-TYPE SYNTAX INTEGER (0..64) UNITS "bits" MAX-ACCESS read-write STATUS current DESCRIPTION "The length of the Interface Identifier in bits." ::= { cIpv6InterfaceEntry 5 } cIpv6InterfacePhysicalAddress OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The interface's physical address. For example, for an IPv6 interface attached to an 802.x link, this object normally contains a MAC address. Note that in some cases this address may differ from the address of the interface's protocol sub-layer. The interface's media-specific MIB must define the bit and byte ordering and the format of the value of this object. For interfaces which do not have such an address (e.g., a serial line), this object should contain an octet string of zero length." ::= { cIpv6InterfaceEntry 6 } -- -- Interface Stats table i.e. ipIfStatsTable, not supported. -- -- -- Internet Address Prefix table -- cIpAddressPfxTable OBJECT-TYPE SYNTAX SEQUENCE OF CIpAddressPfxEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Inet prefix table." ::= { cIp 1 } cIpAddressPfxEntry OBJECT-TYPE SYNTAX CIpAddressPfxEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Inet prefix entry." INDEX { cIpAddressPfxIfIndex, cIpAddressPfxType, cIpAddressPfxPfx, cIpAddressPfxLength } ::= { cIpAddressPfxTable 1 } CIpAddressPfxEntry ::= SEQUENCE { cIpAddressPfxIfIndex InterfaceIndex, cIpAddressPfxType InetAddressType, cIpAddressPfxPfx InetAddress, cIpAddressPfxLength InetAddressPrefixLength, cIpAddressPfxOrigin INTEGER, cIpAddressPfxOnLinkFlag TruthValue, cIpAddressPfxAutonomousFlag TruthValue, cIpAddressPfxAdvPfdLifetime Unsigned32, cIpAddressPfxAdvValidLifetime Unsigned32 } cIpAddressPfxIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface on which this prefix is configured." ::= { cIpAddressPfxEntry 1 } cIpAddressPfxType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address type of cIpAddressPfxPfx. Only IPv4 and IPv6 addresses are expected." ::= { cIpAddressPfxEntry 2 } cIpAddressPfxPfx OBJECT-TYPE SYNTAX InetAddress (SIZE(0..36)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address prefix. Bits after cIpAddressPfxLength must be zero." ::= { cIpAddressPfxEntry 3 } cIpAddressPfxLength OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS not-accessible STATUS current DESCRIPTION "The prefix length associated with this prefix." ::= { cIpAddressPfxEntry 4 } cIpAddressPfxOrigin OBJECT-TYPE SYNTAX INTEGER { other(1), manual(2), wellknown(3), dhcp(4), routeradv(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The origin of this prefix. manual(2) indicates a prefix that was manually configured. wellknown(3) indicates a well-known prefix, e.g. 169.254/16 for IPv4 autoconfiguration or fe80::/10 for IPv6 link-local addresses. dhcp(4) indicates a prefix that was assigned by a DHCP server. routeradv(5) indicates a prefix learned from a router advertisement." ::= { cIpAddressPfxEntry 5 } cIpAddressPfxOnLinkFlag OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object has the value 'true(1)', if this prefix can be used for on-link determination and the value 'false(2)' otherwise." ::= { cIpAddressPfxEntry 6 } cIpAddressPfxAutonomousFlag OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Autonomous address configuration flag. When true(1), indicates that this prefix can be used for autonomous address configuration (i.e. can be used to form a local interface address). If false(2), it is not used to autoconfigure a local interface address." ::= { cIpAddressPfxEntry 7 } cIpAddressPfxAdvPfdLifetime OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The length of time in seconds that this prefix will remain preferred, i.e. time until deprecation. A value of 4,294,967,295 represents infinity. The address generated from a deprecated prefix should no longer be used as a source address in new communications, but packets received on such an interface are processed as expected." ::= { cIpAddressPfxEntry 8 } cIpAddressPfxAdvValidLifetime OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The length of time in seconds that this prefix will remain valid, i.e. time until invalidation. A value of 4,294,967,295 represents infinity. The address generated from an invalidated prefix should not appear as the destination or source address of a packet." ::= { cIpAddressPfxEntry 9 } -- -- Internet Address Table -- cIpAddressTable OBJECT-TYPE SYNTAX SEQUENCE OF CIpAddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Inet address table." ::= { cIp 2 } cIpAddressEntry OBJECT-TYPE SYNTAX CIpAddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Inet addr entry." INDEX { cIpAddressAddrType, cIpAddressAddr } ::= { cIpAddressTable 1 } CIpAddressEntry ::= SEQUENCE { cIpAddressAddrType InetAddressType, cIpAddressAddr InetAddress, cIpAddressIfIndex InterfaceIndex, cIpAddressType INTEGER, cIpAddressPrefix RowPointer, cIpAddressOrigin INTEGER, cIpAddressStatus INTEGER } cIpAddressAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address type of cIpAddressAddr." ::= { cIpAddressEntry 1 } cIpAddressAddr OBJECT-TYPE SYNTAX InetAddress (SIZE(0..36)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP address to which this entry's addressing information pertains." ::= { cIpAddressEntry 2 } cIpAddressIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of the IF-MIB's ifIndex." ::= { cIpAddressEntry 3 } cIpAddressType OBJECT-TYPE SYNTAX INTEGER { unicast(1), anycast(2), broadcast(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of address. broadcast(3) is not a valid value for IPv6 addresses." ::= { cIpAddressEntry 4 } cIpAddressPrefix OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-only STATUS current DESCRIPTION "A pointer to the row in the prefix table to which this address belongs. May be { 0 0 } if there is no such row." ::= { cIpAddressEntry 5 } cIpAddressOrigin OBJECT-TYPE SYNTAX INTEGER { other(1), manual(2), wellknown(3), dhcp(4),-- XXX or assignedbyserver ? linklayer(5), random(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The origin of the address. manual(2) indicates that the address was manually configured. wellknown(3) indicates an address constructed from a well-known value, e.g. an IANA-assigned anycast address. dhcp(4) indicates an address that was assigned to this system by a DHCP server. linklayer(5) indicates an address created by IPv6 stateless autoconfiguration. random(6) indicates an address chosen by random, e.g. an IPv4 address within 169.254/16, or an RFC 3041 privacy address." ::= { cIpAddressEntry 6 } cIpAddressStatus OBJECT-TYPE SYNTAX INTEGER { preferred(1), deprecated(2), invalid(3), inaccessible(4), unknown(5), -- status can not be determined -- for some reason. tentative(6), duplicate(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "Address status. The preferred(1) state indicates that this is a valid address that can appear as the destination or source address of a packet. The deprecated(2) state indicates that this is a valid but deprecated address that should no longer be used as a source address in new communications, but packets addressed to such an address are processed as expected. The invalid(3) state indicates that this is not valid address which should not appear as the destination or source address of a packet. The inaccessible(4) state indicates that the address is not accessible because the interface to which this address is assigned is not operational. The tentative(6) state indicates the uniqueness of the address on the link is being verified. The duplicate(7) state indicates the address has been determined to be non-unique on the link and so must not be used. In the absence of other information, an IPv4 address is always preferred(1)." ::= { cIpAddressEntry 7 } -- -- the Internet Address Translation table -- cInetNetToMediaTable OBJECT-TYPE SYNTAX SEQUENCE OF CInetNetToMediaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP Address Translation table used for mapping from IP addresses to physical addresses. The Address Translation tables contain the IP address to 'physical' address equivalences. Some interfaces do not use translation tables for determining address equivalences (e.g., DDN-X.25 has an algorithmic method); if all interfaces are of this type, then the Address Translation table is empty, i.e., has zero entries." ::= { cIp 3 } cInetNetToMediaEntry OBJECT-TYPE SYNTAX CInetNetToMediaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains one IP address to `physical' address equivalence." INDEX { ifIndex, cInetNetToMediaNetAddressType, cInetNetToMediaNetAddress } ::= { cInetNetToMediaTable 1 } CInetNetToMediaEntry ::= SEQUENCE { cInetNetToMediaNetAddressType InetAddressType, cInetNetToMediaNetAddress InetAddress, cInetNetToMediaPhysAddress PhysAddress, cInetNetToMediaLastUpdated TimeStamp, cInetNetToMediaType INTEGER, cInetNetToMediaState INTEGER } cInetNetToMediaNetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The type of cInetNetToMediaNetAddress." ::= { cInetNetToMediaEntry 1 } cInetNetToMediaNetAddress OBJECT-TYPE SYNTAX InetAddress (SIZE(0..36)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP Address corresponding to the media-dependent `physical' address." ::= { cInetNetToMediaEntry 2 } cInetNetToMediaPhysAddress OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The media-dependent `physical' address." ::= { cInetNetToMediaEntry 3 } cInetNetToMediaLastUpdated OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time this entry was last updated. If this entry was updated prior to the last re- initialization of the local network management subsystem, then this object contains a zero value." ::= { cInetNetToMediaEntry 4 } cInetNetToMediaType OBJECT-TYPE SYNTAX INTEGER { other(1), -- none of the following invalid(2), -- an invalidated mapping dynamic(3), static(4), local(5) -- local interface } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of mapping. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the cInetNetToMediaTable. That is, it effectively disassociates the interface identified with said entry from the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant cInetNetToMediaType object. The 'dynamic(3)' type indicates that the IP address to physical addresses mapping has been dynamically resolved using e.g. IPv4 ARP or the IPv6 Neighbor Discovery protocol. The 'static(4)' type indicates that the mapping has been statically configured. The 'local(5)' type indicates that the mapping is provided for an entity's own interface address." ::= { cInetNetToMediaEntry 5 } cInetNetToMediaState OBJECT-TYPE SYNTAX INTEGER { reachable(1), -- confirmed reachability stale(2), -- unconfirmed reachability delay(3), -- waiting for reachability -- confirmation before entering -- the probe state probe(4), -- actively probing invalid(5), -- an invalidated mapping unknown(6), -- state can not be determined -- for some reason. incomplete(7) -- address resolution is being -- performed. } MAX-ACCESS read-only STATUS current DESCRIPTION "The Neighbor Unreachability Detection [3] state for the interface when the address mapping in this entry is used. If Neighbor Unreachability Detection is not in use (e.g. for IPv4), this object is always unknown(6)." REFERENCE "RFC2461" ::= { cInetNetToMediaEntry 6 } -- -- The IPv6 Scope Identifier Table. -- cIpv6ScopeIdTable OBJECT-TYPE SYNTAX SEQUENCE OF CIpv6ScopeIdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table used to describe IPv6 unicast and multicast scope zones." ::= { cIp 4 } cIpv6ScopeIdEntry OBJECT-TYPE SYNTAX CIpv6ScopeIdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains the list of scope identifiers on a given interface." INDEX { cIpv6ScopeIdIfIndex } ::= { cIpv6ScopeIdTable 1 } CIpv6ScopeIdEntry ::= SEQUENCE { cIpv6ScopeIdIfIndex InterfaceIndex, cIpv6ScopeIdLinkLocal ScopeId, cIpv6ScopeIdSubnetLocal ScopeId, cIpv6ScopeIdAdminLocal ScopeId, cIpv6ScopeIdSiteLocal ScopeId, cIpv6ScopeId6 ScopeId, cIpv6ScopeId7 ScopeId, cIpv6ScopeIdOrganizationLocal ScopeId, cIpv6ScopeId9 ScopeId, cIpv6ScopeIdA ScopeId, cIpv6ScopeIdB ScopeId, cIpv6ScopeIdC ScopeId, cIpv6ScopeIdD ScopeId } cIpv6ScopeIdIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface to which these scopes belong." ::= { cIpv6ScopeIdEntry 1 } cIpv6ScopeIdLinkLocal OBJECT-TYPE SYNTAX ScopeId MAX-ACCESS read-only STATUS current DESCRIPTION "The Scope Identifier for the link-local scope on this interface." ::= { cIpv6ScopeIdEntry 2 } cIpv6ScopeIdSubnetLocal OBJECT-TYPE SYNTAX ScopeId MAX-ACCESS read-only STATUS current DESCRIPTION "The Scope Identifier for the subnet-local scope on this interface." ::= { cIpv6ScopeIdEntry 3 } cIpv6ScopeIdAdminLocal OBJECT-TYPE SYNTAX ScopeId MAX-ACCESS read-only STATUS current DESCRIPTION "The Scope Identifier for the admin-local scope on this interface." ::= { cIpv6ScopeIdEntry 4 } cIpv6ScopeIdSiteLocal OBJECT-TYPE SYNTAX ScopeId MAX-ACCESS read-only STATUS current DESCRIPTION "The Scope Identifier for the site-local scope on this interface." ::= { cIpv6ScopeIdEntry 5 } cIpv6ScopeId6 OBJECT-TYPE SYNTAX ScopeId MAX-ACCESS read-only STATUS current DESCRIPTION "The Scope Identifier for scope 6 on this interface." ::= { cIpv6ScopeIdEntry 6 } cIpv6ScopeId7 OBJECT-TYPE SYNTAX ScopeId MAX-ACCESS read-only STATUS current DESCRIPTION "The Scope Identifier for scope 7 on this interface." ::= { cIpv6ScopeIdEntry 7 } cIpv6ScopeIdOrganizationLocal OBJECT-TYPE SYNTAX ScopeId MAX-ACCESS read-only STATUS current DESCRIPTION "The Scope Identifier for the orgainzation-local scope on this interface." ::= { cIpv6ScopeIdEntry 8 } cIpv6ScopeId9 OBJECT-TYPE SYNTAX ScopeId MAX-ACCESS read-only STATUS current DESCRIPTION "The Scope Identifier for scope 9 on this interface." ::= { cIpv6ScopeIdEntry 9 } cIpv6ScopeIdA OBJECT-TYPE SYNTAX ScopeId MAX-ACCESS read-only STATUS current DESCRIPTION "The Scope Identifier for scope A on this interface." ::= { cIpv6ScopeIdEntry 10 } cIpv6ScopeIdB OBJECT-TYPE SYNTAX ScopeId MAX-ACCESS read-only STATUS current DESCRIPTION "The Scope Identifier for scope B on this interface." ::= { cIpv6ScopeIdEntry 11 } cIpv6ScopeIdC OBJECT-TYPE SYNTAX ScopeId MAX-ACCESS read-only STATUS current DESCRIPTION "The Scope Identifier for scope C on this interface." ::= { cIpv6ScopeIdEntry 12 } cIpv6ScopeIdD OBJECT-TYPE SYNTAX ScopeId MAX-ACCESS read-only STATUS current DESCRIPTION "The Scope Identifier for scope D on this interface." ::= { cIpv6ScopeIdEntry 13 } -- -- ICMP non-message-specific counters -- cInetIcmpTable OBJECT-TYPE SYNTAX SEQUENCE OF CInetIcmpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of generic ICMP counters. These counters may be kept per-interface and/or system-wide." ::= { cIcmp 1 } cInetIcmpEntry OBJECT-TYPE SYNTAX CInetIcmpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the inetIcmpTable. A row with an inetIcmpIfIndex value of zero indicates a system-wide value; a row with a non-zero inetIcmpIfIndex indicates an interface-specific value. A system may provide both system-wide and interface-specific values, in which case it is important to note that the system-wide value may not be equal to the sum of the interface-specific value across all interfaces due to e.g. dynamic interface creation/deletion." INDEX { cInetIcmpAFType, cInetIcmpIfIndex } ::= { cInetIcmpTable 1 } CInetIcmpEntry ::= SEQUENCE { cInetIcmpAFType InetAddressType, cInetIcmpIfIndex InterfaceIndexOrZero, cInetIcmpInMsgs Counter32, cInetIcmpInErrors Counter32, cInetIcmpOutMsgs Counter32, cInetIcmpOutErrors Counter32 } cInetIcmpAFType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP address family of the statistics." ::= { cInetIcmpEntry 1 } cInetIcmpIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ifindex of the interface, or zero for system-wide stats." ::= { cInetIcmpEntry 2 } cInetIcmpInMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of ICMP messages which the entity received. Note that this counter includes all those counted by cInetIcmpInErrors." ::= { cInetIcmpEntry 3 } cInetIcmpInErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP messages which the entity received but determined as having ICMP-specific errors (bad ICMP checksums, bad length, etc.)." ::= { cInetIcmpEntry 4 } cInetIcmpOutMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of ICMP messages which the entity received. Note that this counter includes all those counted by inetIcmpOutErrors." ::= { cInetIcmpEntry 5 } cInetIcmpOutErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP messages which this entity did not send due to problems discovered within ICMP such as a lack of buffers. This value should not include errors discovered outside the ICMP layer such as the inability of IP to route the resultant datagram. In some implementations there may be no types of error which contribute to this counter's value." ::= { cInetIcmpEntry 6 } -- -- per-AF, per-interface(optionally), per-msg type and code ICMP -- counters -- cInetIcmpMsgTable OBJECT-TYPE SYNTAX SEQUENCE OF CInetIcmpMsgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of per-message ICMP counters. These counters may be kept per-interface and/or system-wide." ::= { cIcmp 2 } cInetIcmpMsgEntry OBJECT-TYPE SYNTAX CInetIcmpMsgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the inetIcmpMsgTable. A row with an inetIcmpMsgIfIndex value of zero indicates a system-wide value; a row with a non-zero cInetIcmpMsgIfIndex indicates an interface-specific value. A system may provide both system-wide and interface-specific values, in which case it is important to note that the system-wide value may not be equal to the sum of the interface-specific values across all interfaces due to e.g. dynamic interface creation/deletion. If the system keeps track of individual ICMP code values (e.g. destination unreachable, code administratively prohibited), it creates several rows for each inetIcmpMsgType, each with an appropriate value of cInetIcmpMsgCode. A row with the special value of cInetIcmpMsgCode, 256, counts all packets with type cInetIcmpMsgType that aren't counted in rows with a value of cInetIcmpMsgCode other than 256." INDEX { cInetIcmpMsgAFType, cInetIcmpMsgIfIndex, cInetIcmpMsgType, cInetIcmpMsgCode } ::= { cInetIcmpMsgTable 1 } CInetIcmpMsgEntry ::= SEQUENCE { cInetIcmpMsgAFType InetAddressType, cInetIcmpMsgIfIndex InterfaceIndexOrZero, cInetIcmpMsgType Integer32, cInetIcmpMsgCode Integer32, cInetIcmpMsgInPkts Counter32, cInetIcmpMsgOutPkts Counter32 } cInetIcmpMsgAFType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP address family of the statistics." ::= { cInetIcmpMsgEntry 1 } cInetIcmpMsgIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ifindex of the interface, or zero for system-wide stats." ::= { cInetIcmpMsgEntry 2 } cInetIcmpMsgType OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ICMP type field of the message type being counted by this row." ::= { cInetIcmpMsgEntry 3 } cInetIcmpMsgCode OBJECT-TYPE SYNTAX Integer32 (0..256) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ICMP code field of the message type being counted by this row, or the special value 256 if no specific ICMP code is counted by this row." ::= { cInetIcmpMsgEntry 4 } cInetIcmpMsgInPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of input packets for this AF, ifindex, type, code." ::= { cInetIcmpMsgEntry 5 } cInetIcmpMsgOutPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of output packets for this AF, ifindex, type, code." ::= { cInetIcmpMsgEntry 6 } -- -- Conformance information -- ciscoIpMIBConformance OBJECT IDENTIFIER ::= { ciscoIetfIpMIB 2 } ciscoIpMIBCompliances OBJECT IDENTIFIER ::= { ciscoIpMIBConformance 1 } ciscoIpMIBGroups OBJECT IDENTIFIER ::= { ciscoIpMIBConformance 2 } -- -- Compliance statements -- ciscoIpMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for systems which implement IPv6 OR IPv4." MODULE -- this module MANDATORY-GROUPS { ciscoIpAddressPfxGroup, ciscoIpAddressGroup, ciscoInetNetToMediaGroup, ciscoInetIcmpGroup, ciscoInetIcmpMsgGroup } GROUP ciscoIpv6GeneralGroup DESCRIPTION "This group is mandatory only when IPv6 is implemented on the system." GROUP ciscoIpv6InterfaceGroup DESCRIPTION "This group is mandatory only when IPv6 is implemented on the system." GROUP ciscoIpv6ScopeGroup DESCRIPTION "The group is mandatory onle when IPv6 scoped architecture has been implemented on the system." ::= { ciscoIpMIBCompliances 1 } -- units of conformance ciscoIpAddressPfxGroup OBJECT-GROUP OBJECTS { cIpAddressPfxOrigin, cIpAddressPfxOnLinkFlag, cIpAddressPfxAutonomousFlag, cIpAddressPfxAdvPfdLifetime, cIpAddressPfxAdvValidLifetime } STATUS current DESCRIPTION "The ip version independent address prefix group of entries providing for basic management of IP prefixes." ::= { ciscoIpMIBGroups 1 } ciscoIpAddressGroup OBJECT-GROUP OBJECTS { cIpAddressIfIndex, cIpAddressType, cIpAddressPrefix, cIpAddressOrigin, cIpAddressStatus } STATUS current DESCRIPTION "The ip version independent address group of entries providing for basic management of IP addresses." ::= { ciscoIpMIBGroups 2 } ciscoInetNetToMediaGroup OBJECT-GROUP OBJECTS { cInetNetToMediaPhysAddress, cInetNetToMediaLastUpdated, cInetNetToMediaType, cInetNetToMediaState } STATUS current DESCRIPTION "The group of entries providing IP address to physical address mapping." ::= { ciscoIpMIBGroups 3 } ciscoInetIcmpGroup OBJECT-GROUP OBJECTS { cInetIcmpInMsgs, cInetIcmpInErrors, cInetIcmpOutMsgs, cInetIcmpOutErrors } STATUS current DESCRIPTION "The group of entries providing version independent per-interface ICMP specific counters." ::= { ciscoIpMIBGroups 4 } ciscoInetIcmpMsgGroup OBJECT-GROUP OBJECTS { cInetIcmpMsgInPkts, cInetIcmpMsgOutPkts } STATUS current DESCRIPTION "The group of entries providing version independent per-interface ICMP msg type specific counters." ::= { ciscoIpMIBGroups 5 } ciscoIpv6GeneralGroup OBJECT-GROUP OBJECTS { cIpv6Forwarding, cIpv6DefaultHopLimit } STATUS current DESCRIPTION "The IPv6 group of objects providing for basic management of IPv6 entities." ::= { ciscoIpMIBGroups 6 } ciscoIpv6InterfaceGroup OBJECT-GROUP OBJECTS { cIpv6InterfaceEffectiveMtu, cIpv6InterfaceReasmMaxSize, cIpv6InterfaceIdentifier, cIpv6InterfaceIdentifierLength, cIpv6InterfacePhysicalAddress } STATUS current DESCRIPTION "The IPv6 group of objects providing IPv6 interface specific statistics." ::= { ciscoIpMIBGroups 7 } ciscoIpv6ScopeGroup OBJECT-GROUP OBJECTS { cIpv6ScopeIdLinkLocal, cIpv6ScopeIdSubnetLocal, cIpv6ScopeIdAdminLocal, cIpv6ScopeIdSiteLocal, cIpv6ScopeId6, cIpv6ScopeId7, cIpv6ScopeIdOrganizationLocal, cIpv6ScopeId9, cIpv6ScopeIdA, cIpv6ScopeIdB, cIpv6ScopeIdC, cIpv6ScopeIdD } STATUS current DESCRIPTION "The group of objects for managing IPv6 scope zones." ::= { ciscoIpMIBGroups 8 } END