-- ******************************************************************* -- Description of managed objects for Ethernet access interfaces. -- -- January 2005, Gunnar Lovblom -- -- Copyright (c) 2005, 2007, 2009 by Cisco Systems Inc. -- All rights reserved. -- ****************************************************************** CISCO-ETHERNET-ACCESS-MIB DEFINITIONS ::= BEGIN IMPORTS Integer32, MODULE-IDENTITY, OBJECT-TYPE FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF TEXTUAL-CONVENTION FROM SNMPv2-TC ifIndex FROM IF-MIB vtpVlanIndex, managementDomainIndex FROM CISCO-VTP-MIB ciscoMgmt FROM CISCO-SMI; ciscoEthernetAccessMIB MODULE-IDENTITY LAST-UPDATED "200709140000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 Tel: +1 800 553-NETS E-mail: cs-dsbu@cisco.com" DESCRIPTION "The tables defined by this MIB module contain a collection of managed objects that are general in nature and apply to an edge device in an organizations network, e.g. a Metro Ethernet network. An edge device, is a customer located equipment, this is the first device which will connect the Service Provider's network and map subscriber traffic into the next layer. The access media could be either CAT5 or fiber. The access device (edge device) can be designed for DSL, Ethernet or other technologies, however, this MIB is designed for Ethernet. Terminology: UNI - User to Network Interface NNI - Network to Network Interface. ENI - Enhanced Network Interface. Enhanced UNI port. module/device - In an environment (specifically, in an SNMP context) consisting of a single chassis which can contain multiple cards, the term 'module' refers to a card and the term 'device' refers to the whole chassis. In an environment where multiple chassis are 'stacked' together, the term 'module' refers to a chassis and the term 'device' refers to the whole stack. In an environment containing only a single chassis without removable cards, the terms 'device' and 'module' both refer to the chassis and its contents." REVISION "200709140000Z" DESCRIPTION "Added ENI as a new port type to the ceaPortType and ceaPortCapability objects." REVISION "200501180000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 466 } -- MIB Objects Definitions ciscoEthernetAccessMIBObjects OBJECT IDENTIFIER ::= { ciscoEthernetAccessMIB 1 } ciscoEthernetAccessMIBConform OBJECT IDENTIFIER ::= { ciscoEthernetAccessMIB 2 } ceaGlobals OBJECT IDENTIFIER ::= { ciscoEthernetAccessMIBObjects 1 } ceaConfig OBJECT IDENTIFIER ::= { ciscoEthernetAccessMIBObjects 2 } -- Textual Conventions CeaVlanUNIType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The type of a VLAN. 'other' -- this VLAN is not a UNI VLAN 'isolated' -- this VLAN is a UNI isolated VLAN. UNI ports that are members of a UNI isolated VLAN can not communicate with other ports in that VLAN, however NNI ports can communicate with UNI and NNI ports in the same VLAN. 'community' -- this VLAN is a UNI community VLAN. UNI and NNI ports that are members of the community VLAN can communicate with all other UNI and NNI ports in the same VLAN." SYNTAX INTEGER { other(1), isolated(2), community(3) } ceaMaxNNIPorts OBJECT-TYPE SYNTAX Integer32 (0..512) MAX-ACCESS read-only STATUS current DESCRIPTION "The max number of interfaces per module for which the ceaPortType can have the value 'nni'. The value of 0 is returned by this object if there is no limitation to the number of NNI ports." ::= { ceaGlobals 1 } ceaMaxUNIVlanCommunityPorts OBJECT-TYPE SYNTAX Integer32 (0..512) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of ports on this device for which the ceaUNIVlanType object can have the value 'community'. The value of 0 is returned by this object if there is no limitation to the number of UNI VLAN Communities." ::= { ceaGlobals 2 } -- ceaPortTable ceaPortTable OBJECT-TYPE SYNTAX SEQUENCE OF CeaPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains Ethernet port specific information. There exists an entry for each Ethernet port with an ifType of 6 (ethernetCsmacd) in this table. Note that the maximum number of NNI ports that can be configured per module on this device is given by the value of ceaMaxNNIPorts." ::= { ceaConfig 1 } ceaPortEntry OBJECT-TYPE SYNTAX CeaPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A set of Ethernet port specific parameters for a device which can be configured with a mixture of port types defined by the ceaPortType object." INDEX { ifIndex } ::= { ceaPortTable 1 } CeaPortEntry ::= SEQUENCE { ceaPortType INTEGER, ceaPortCapability BITS } ceaPortType OBJECT-TYPE SYNTAX INTEGER { unspecified(1), uni(2), nni(3), eni(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "The current configuration of the port. Only ports that are supported by the ceaPortCapability object can be set. Unspecified port type is any other port type than NNI, UNI or ENI. unspecified = Not UNI, or NNI, or ENI uni = User to Network Interface port type. nni = Network to Network Interface port type. eni = Enhanced UNI port type." ::= { ceaPortEntry 1 } ceaPortCapability OBJECT-TYPE SYNTAX BITS { nni(0), uni(1), eni(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Types supported by the Ethernet port. If a port doesn't support the port type the ceaPortType will not allow set of the unsupported type. nni = Port supports NNI. uni = Port supports UNI. eni = Port supports ENI." ::= { ceaPortEntry 2 } -- ceaUNIVlanTable ceaUNIVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF CeaUNIVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains UNI VLAN information for all the VLANs which currently exist on this device. The number of UNI ports that can belong to a VLAN type 'community' is limited by the ceaMaxUNIVlanCommunityPorts object." ::= { ceaConfig 2 } ceaUNIVlanEntry OBJECT-TYPE SYNTAX CeaUNIVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "There is an entry in this table for each VLAN that exist on this device." INDEX { managementDomainIndex, vtpVlanIndex } ::= { ceaUNIVlanTable 1 } CeaUNIVlanEntry ::= SEQUENCE { ceaUNIVlanType CeaVlanUNIType } ceaUNIVlanType OBJECT-TYPE SYNTAX CeaVlanUNIType MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates the VLAN type defined for the UNI VLAN." ::= { ceaUNIVlanEntry 1 } -- MIB Conformance Statements cEthernetAccessMIBCompliances OBJECT IDENTIFIER ::= { ciscoEthernetAccessMIBConform 1 } cEthernetAccessMIBGroups OBJECT IDENTIFIER ::= { ciscoEthernetAccessMIBConform 2 } -- Compliance cEthernetAccessMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities that implement the CISCO-ETHERNET-ACCESS-MIB. Implementation of this MIB is mandatory for any platform that have Ethernet UNI/NNI capable interfaces." MODULE -- this module MANDATORY-GROUPS { ceaPortGroup, ceaVlanGroup } OBJECT ceaUNIVlanType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ceaPortType MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { cEthernetAccessMIBCompliances 1 } -- Units of Conformance ceaPortGroup OBJECT-GROUP OBJECTS { ceaMaxNNIPorts, ceaPortType, ceaPortCapability } STATUS current DESCRIPTION "A collection of managed objects defining port types." ::= { cEthernetAccessMIBGroups 1 } ceaVlanGroup OBJECT-GROUP OBJECTS { ceaMaxUNIVlanCommunityPorts, ceaUNIVlanType } STATUS current DESCRIPTION "A collection of managed objects defining VLAN types." ::= { cEthernetAccessMIBGroups 2 } END