-- ***************************************************************** -- CISCO-ENTITY-QFP-MIB.my -- -- This MIB module is used to monitor Quantum Flow Processors (QFP). -- -- November 2009, Muthukrishnan Venkatraman -- -- Copyright (c) 2009 by cisco Systems, Inc. -- All rights reserved. -- -- ***************************************************************** CISCO-ENTITY-QFP-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Gauge32, NOTIFICATION-TYPE, Counter32, Counter64, Unsigned32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF TEXTUAL-CONVENTION, DateAndTime, TruthValue FROM SNMPv2-TC entPhysicalIndex FROM ENTITY-MIB ciscoMgmt FROM CISCO-SMI; ciscoEntityQfpMIB MODULE-IDENTITY LAST-UPDATED "200912020000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-snmp@cisco.com" DESCRIPTION "This MIB module defines managed objects that facilitate the management of Quantum Flow Processors (QFP), which are listed in the ENTITY-MIB (RFC 4133) entPhysicalTable as an entPhysicalClass of 'cpu'. The Quantum Flow Processors (QFP) technology is an architecture family developed by Cisco, which has fully integrated and programmable networking chip set that controls different functions of a system such as packet forwarding. This module contains objects to monitor various QFP statistics such as system, utilization, memory, etc. The utilization statistics can be used for future capacity planning. The calculation of this statistics may vary by devices which host QFPs, hence the user must refer to the specific device document of interest for the exact method of calculation. The utilization statistics have the following terminology. o Input - Communication channel where packets arrive on the QFP. o Output - Communication channel where packets leave the QFP. o Priority - A classification applied to packets indicating they should be treated with greater urgency. o Non-Priority - A classification applied to packets indicating they should be treated with lesser urgency. o Processing Load - The percentage of time over some interval that the QFP has spent forwarding packets, relative to the total time spent both forwarding packets and being idle." REVISION "200912020000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 715 } CiscoQfpPacketRate ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "An estimate of throughput in units of packets per second. The CiscoQfpPacketRate type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value of Counter64. The Counter64 syntax is used for encoding rules." SYNTAX Counter64 CiscoQfpBitRate ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "An estimate of throughput in units of bits per second. The CiscoQfpBitRate type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value of Counter64. The Counter64 syntax is used for encoding rules." SYNTAX Counter64 CiscoQfpTimeInterval ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "An enumerated integer-value describing the available interval values for which the periodic statistics are to be collected. fiveSeconds (1) - Interval to collect last 5 seconds statistics oneMinute(2) - Interval to collect last 1 minute statistics fiveMinutes(3) - Interval to collect last 5 minutes statistics sixtyMinutes(4) - Interval to collect last 60 minutes statistics" SYNTAX INTEGER { fiveSeconds(1), oneMinute(2), fiveMinutes(3), sixtyMinutes(4) } CiscoQfpMemoryResource ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "An enumerated integer-value describing various memory resources used by the QFP. dram (1) - Dynamic Random Access Memory (DRAM) memory resource" SYNTAX INTEGER { dram(1) } ciscoEntityQfpMIBNotifs OBJECT IDENTIFIER ::= { ciscoEntityQfpMIB 0 } ciscoEntityQfpMIBObjects OBJECT IDENTIFIER ::= { ciscoEntityQfpMIB 1 } ciscoEntityQfpMIBConform OBJECT IDENTIFIER ::= { ciscoEntityQfpMIB 2 } ciscoEntityQfp OBJECT IDENTIFIER ::= { ciscoEntityQfpMIBObjects 1 } ciscoEntityQfpNotif OBJECT IDENTIFIER ::= { ciscoEntityQfpMIBObjects 2 } ceqfpSystemTable OBJECT-TYPE SYNTAX SEQUENCE OF CeqfpSystemEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table maintains the QFP system information for each QFP physical entity. An agent creates a conceptual row to this table corresponding to a QFP physical entity upon detection of a physical entity supporting the QFP system information. An agent destroys a conceptual row from this table corresponding to a QFP physical entity upon removal of the QFP host physical entity." ::= { ciscoEntityQfp 1 } ceqfpSystemEntry OBJECT-TYPE SYNTAX CeqfpSystemEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the ceqfpSystemTable. There is an entry in this table for each QFP entity, as defined by a value of entPhysicalIndex." INDEX { entPhysicalIndex } ::= { ceqfpSystemTable 1 } CeqfpSystemEntry ::= SEQUENCE { ceqfpSystemTrafficDirection INTEGER, ceqfpSystemState INTEGER, ceqfpNumberSystemLoads Counter32, ceqfpSystemLastLoadTime DateAndTime } ceqfpSystemTrafficDirection OBJECT-TYPE SYNTAX INTEGER { none(1), ingress(2), egress(3), both(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the traffic direction that this QFP is assigned to process. The enumerated values are described below. none (1) - The QFP is not assigned to processes any traffic yet ingress (2) - The QFP processes inbound traffic egress (3) - The QFP processes outbound traffic both (4) - The QFP processes both inbound and outbound traffic" ::= { ceqfpSystemEntry 1 } ceqfpSystemState OBJECT-TYPE SYNTAX INTEGER { unknown(1), reset(2), init(3), active(4), activeSolo(5), standby(6), hotStandby(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the current QFP state. The enumerated values are described below. unknown (1) - The state of the QFP is unknown reset (2) - The QFP is reset init (3) - The QFP is being initialized active (4) - The QFP is active in a system with redundant QFP activeSolo (5) - The QFP is active and there is no redundant QFP in the system standby (6) - The QFP is standby in a redundant system. hotStandby (7) - The QFP is standby and synchronized with active, so that a switchover in this state will preserve state of the active. Stateful datapath features are synchronized between the active QFP and standby QFP" ::= { ceqfpSystemEntry 2 } ceqfpNumberSystemLoads OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the number of times the QFP is loaded, since the QFP host is up." ::= { ceqfpSystemEntry 3 } ceqfpSystemLastLoadTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the QFP last load time." ::= { ceqfpSystemEntry 4 } ceqfpFiveSecondUtilAlgo OBJECT-TYPE SYNTAX INTEGER { unknown(1), fiveSecSample(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This objects represents the method used to calculate 5 Second interval utilization data. The enumerated values are described below. unknown (1) - The calculation method is unknown fiveSecSample (2) - The value is calculated based on the last 5 second sampling period of utilization data." ::= { ciscoEntityQfp 2 } ceqfpOneMinuteUtilAlgo OBJECT-TYPE SYNTAX INTEGER { unknown(1), fiveSecSMA(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This objects represents the method used to calculate 1 Minute interval utilization data. The enumerated values are described below. unknown (1) - The calculation method is unknown fiveSecSMA (2) - The value is calculated using Simple Moving Average of last 12 five seconds utilization data." ::= { ciscoEntityQfp 3 } ceqfpFiveMinutesUtilAlgo OBJECT-TYPE SYNTAX INTEGER { unknown(1), fiveSecSMA(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This objects represents the method used to calculate 5 Minutes interval utilization data. The enumerated values are described below. unknown (1) - The calculation method is unknown fiveSecSMA (2) - The value is calculated using Simple Moving Average of last 60 five seconds utilization data." ::= { ciscoEntityQfp 4 } ceqfpSixtyMinutesUtilAlgo OBJECT-TYPE SYNTAX INTEGER { unknown(1), fiveSecSMA(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This objects represents the method used to calculate 60 Minutes interval utilization data. The enumerated values are described below. unknown (1) - The calculation method is unknown fiveSecSMA (1) - The value is calculated using Simple Moving Average of last 720 five seconds utilization data." ::= { ciscoEntityQfp 5 } ceqfpUtilizationTable OBJECT-TYPE SYNTAX SEQUENCE OF CeqfpUtilizationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table maintains the utilization statistics collected by each QFP physical entity at various time interval such as last 5 seconds, 1 minute, etc. An agent creates a conceptual row to this table corresponding to a QFP physical entity for a time interval upon detection of a physical entity supporting the utilization statistics for a time interval. The agent destroys a conceptual row from this table corresponding to a QFP physical entity for a time interval upon removal of the QFP host physical entity or it does not receive the utilization statistics update for a certain time period. The time period to wait before deleting an entry from this table would be the discretion of the supporting device." ::= { ciscoEntityQfp 6 } ceqfpUtilizationEntry OBJECT-TYPE SYNTAX CeqfpUtilizationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the ceqfpUtilizationTable. There is an entry in this table for each QFP entity by a value of entPhysicalIndex and the supported time interval by a value of ceqfpUtilTimeInterval. The method of utilization data calculation for each interval period can be identified through the respective interval scalar objects. For example the utilizaiton data calculation method for 'fiveSecond' interval can be identified by ceqfpFiveSecondUtilAlgo." INDEX { entPhysicalIndex, ceqfpUtilTimeInterval } ::= { ceqfpUtilizationTable 1 } CeqfpUtilizationEntry ::= SEQUENCE { ceqfpUtilTimeInterval CiscoQfpTimeInterval, ceqfpUtilInputPriorityPktRate CiscoQfpPacketRate, ceqfpUtilInputPriorityBitRate CiscoQfpBitRate, ceqfpUtilInputNonPriorityPktRate CiscoQfpPacketRate, ceqfpUtilInputNonPriorityBitRate CiscoQfpBitRate, ceqfpUtilInputTotalPktRate CiscoQfpPacketRate, ceqfpUtilInputTotalBitRate CiscoQfpBitRate, ceqfpUtilOutputPriorityPktRate CiscoQfpPacketRate, ceqfpUtilOutputPriorityBitRate CiscoQfpBitRate, ceqfpUtilOutputNonPriorityPktRate CiscoQfpPacketRate, ceqfpUtilOutputNonPriorityBitRate CiscoQfpBitRate, ceqfpUtilOutputTotalPktRate CiscoQfpPacketRate, ceqfpUtilOutputTotalBitRate CiscoQfpBitRate, ceqfpUtilProcessingLoad Gauge32 } ceqfpUtilTimeInterval OBJECT-TYPE SYNTAX CiscoQfpTimeInterval MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies the time interval for which the utilization statistics being collected. The interval values can be 5 second, 1 minute, etc. as specified in the CiscoQfpTimeInterval." ::= { ceqfpUtilizationEntry 1 } ceqfpUtilInputPriorityPktRate OBJECT-TYPE SYNTAX CiscoQfpPacketRate UNITS "packets per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the QFP input channel priority packet rate during this interval." ::= { ceqfpUtilizationEntry 2 } ceqfpUtilInputPriorityBitRate OBJECT-TYPE SYNTAX CiscoQfpBitRate UNITS "bits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the QFP input channel priority bit rate during this interval." ::= { ceqfpUtilizationEntry 3 } ceqfpUtilInputNonPriorityPktRate OBJECT-TYPE SYNTAX CiscoQfpPacketRate UNITS "packets per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the QFP input channel non-priority packet rate during this interval." ::= { ceqfpUtilizationEntry 4 } ceqfpUtilInputNonPriorityBitRate OBJECT-TYPE SYNTAX CiscoQfpBitRate UNITS "bits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the QFP input channel non-priority bit rate during this interval." ::= { ceqfpUtilizationEntry 5 } ceqfpUtilInputTotalPktRate OBJECT-TYPE SYNTAX CiscoQfpPacketRate UNITS "packets per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the QFP input channel total packet rate during this interval, which includes both priority and non-priority input packet rate." ::= { ceqfpUtilizationEntry 6 } ceqfpUtilInputTotalBitRate OBJECT-TYPE SYNTAX CiscoQfpBitRate UNITS "bits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the QFP input channel total bit rate during this interval, which includes both priority and non-priority input bit rate." ::= { ceqfpUtilizationEntry 7 } ceqfpUtilOutputPriorityPktRate OBJECT-TYPE SYNTAX CiscoQfpPacketRate UNITS "packets per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the QFP output channel priority packet rate during this interval." ::= { ceqfpUtilizationEntry 8 } ceqfpUtilOutputPriorityBitRate OBJECT-TYPE SYNTAX CiscoQfpBitRate UNITS "bits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the QFP output channel priority bit rate during this interval." ::= { ceqfpUtilizationEntry 9 } ceqfpUtilOutputNonPriorityPktRate OBJECT-TYPE SYNTAX CiscoQfpPacketRate UNITS "packets per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the QFP output channel non-priority packet rate during this interval." ::= { ceqfpUtilizationEntry 10 } ceqfpUtilOutputNonPriorityBitRate OBJECT-TYPE SYNTAX CiscoQfpBitRate UNITS "bits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the QFP output channel non-priority bit rate during this interval." ::= { ceqfpUtilizationEntry 11 } ceqfpUtilOutputTotalPktRate OBJECT-TYPE SYNTAX CiscoQfpPacketRate UNITS "packets per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the QFP output channel total packet rate during this interval, which includes both priority and non-priority output packet rate." ::= { ceqfpUtilizationEntry 12 } ceqfpUtilOutputTotalBitRate OBJECT-TYPE SYNTAX CiscoQfpBitRate UNITS "bits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the QFP output channel total bit rate during this interval, which includes both priority and non-priority bit rate." ::= { ceqfpUtilizationEntry 13 } ceqfpUtilProcessingLoad OBJECT-TYPE SYNTAX Gauge32 (0..100) UNITS "percent" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the QFP processing load during this interval." ::= { ceqfpUtilizationEntry 14 } ceqfpMemoryResourceTable OBJECT-TYPE SYNTAX SEQUENCE OF CeqfpMemoryResourceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table maintains the memory resources statistics for each QFP physical entity. An agent creates a conceptual row to this table corresponding to a QFP physical entity and its supported memory resource type upon detection of a physical entity supporting the memory resource statistics for a memory resource type. An agent destroys a conceptual row from this table corresponding to a QFP physical entity and its supported memory resource type upon removal of the QFP host physical entity or it does not receive memory resource statistics update for a certain time period. The time period to wait before deleting an entry from this table would be the discretion of the supporting device." ::= { ciscoEntityQfp 7 } ceqfpMemoryResourceEntry OBJECT-TYPE SYNTAX CeqfpMemoryResourceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the ceqfpMemoryResourceTable. There is an entry in this table for each QFP entity by a value of entPhysicalIndex and the supported memory resource type by a value of ceqfpMemoryResType." INDEX { entPhysicalIndex, ceqfpMemoryResType } ::= { ceqfpMemoryResourceTable 1 } CeqfpMemoryResourceEntry ::= SEQUENCE { ceqfpMemoryResType CiscoQfpMemoryResource, ceqfpMemoryResTotal Gauge32, ceqfpMemoryResInUse Gauge32, ceqfpMemoryResFree Gauge32, ceqfpMemoryResLowFreeWatermark Gauge32, ceqfpMemoryResRisingThreshold Unsigned32, ceqfpMemoryResFallingThreshold Unsigned32 } ceqfpMemoryResType OBJECT-TYPE SYNTAX CiscoQfpMemoryResource MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the type of the memory resource used by the QFP. This object is one of the indices to uniquely identify the QFP memory resource type." ::= { ceqfpMemoryResourceEntry 1 } ceqfpMemoryResTotal OBJECT-TYPE SYNTAX Gauge32 UNITS "kilo bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents total memory available on this memory resource." ::= { ceqfpMemoryResourceEntry 2 } ceqfpMemoryResInUse OBJECT-TYPE SYNTAX Gauge32 UNITS "kilo bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the memory which is currently under use on this memory resource." ::= { ceqfpMemoryResourceEntry 3 } ceqfpMemoryResFree OBJECT-TYPE SYNTAX Gauge32 UNITS "kilo bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the memory which is currently free on this memory resource." ::= { ceqfpMemoryResourceEntry 4 } ceqfpMemoryResLowFreeWatermark OBJECT-TYPE SYNTAX Gauge32 UNITS "kilo bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents lowest free water mark on this memory resource." ::= { ceqfpMemoryResourceEntry 5 } ceqfpMemoryResRisingThreshold OBJECT-TYPE SYNTAX Unsigned32 (0..100) UNITS "percent" MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the rising threshold value for this memory resource. A value of zero means that the rising threshold is not supported for this memory resource. The value of this object can not be set to lower than or equal to ceqfpMemoryResFallingThreshold. A rising (ceqfpMemoryResRisingThreshNotif) notification will be generated, whenever the memory resource usage (ceqfpMemoryResInUse) is equal to or greater than this value. After a rising notification is generated, another such notification will not be generated until the ceqfpMemoryResInUse falls below this value and reaches the ceqfpMemoryResFallingThreshold." DEFVAL { 90 } ::= { ceqfpMemoryResourceEntry 6 } ceqfpMemoryResFallingThreshold OBJECT-TYPE SYNTAX Unsigned32 (0..100) UNITS "percent" MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the falling threshold value for this memory resource. A value of zero means that the falling threshold is not supported for this memory resource. The value of this object can not be set to higher than or equal to ceqfpMemoryResRisingThreshold. A falling (ceqfpMemoryResRisingThreshNotif) notification will be generated, whenever the memory resource usage (ceqfpMemoryResInUse) is equal to or lesser than this value. After a falling notification is generated, another such notification will not be generated until the ceqfpMemoryResInUse rises above this value and reaches the ceqfpMemoryResRisingThreshold." DEFVAL { 85 } ::= { ceqfpMemoryResourceEntry 7 } ceqfpMemoryResThreshNotifEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object controls memory resource rising and falling threshold notification. When this object contains a value 'true', then generation of memory resource threshold notification is enabled. If this object contains a value 'false', then generation of memory resource threshold notification is disabled." DEFVAL { false } ::= { ciscoEntityQfpNotif 1 } ceqfpMemoryResCurrentRisingThresh OBJECT-TYPE SYNTAX Unsigned32 (1..100) UNITS "percent" MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object respresents the current rising threshold value, which triggers the rising threshold notificaiton (ceqfpMemoryResRisingThreshNotif)." ::= { ciscoEntityQfpNotif 2 } ceqfpMemoryResCurrentFallingThresh OBJECT-TYPE SYNTAX Unsigned32 UNITS "percent" MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object respresents the current falling threshold value, which triggers the falling threshold notificaiton (ceqfpMemoryResFallingThreshNotif)." ::= { ciscoEntityQfpNotif 3 } ciscoEntityQfpMIBCompliances OBJECT IDENTIFIER ::= { ciscoEntityQfpMIBConform 1 } ceqfpMemoryResRisingThreshNotif NOTIFICATION-TYPE OBJECTS { ceqfpMemoryResInUse, ceqfpMemoryResCurrentRisingThresh } STATUS current DESCRIPTION "A notification indicating that the QFP memory usage is rising the threshold on this memory resource. This notification will be sent, whenever the QFP memory usage (ceqfpMemoryResInUse) is equal to or above the rising threshold (ceqfpMemoryResRisingThreshold). An agent may throttle the generation of consecutive ceqfpMemoryResRisingThreshNotif notification so that there is at least a five second (suggested default) gap between notification of this type." ::= { ciscoEntityQfpMIBNotifs 1 } ceqfpMemoryResFallingThreshNotif NOTIFICATION-TYPE OBJECTS { ceqfpMemoryResInUse, ceqfpMemoryResCurrentFallingThresh } STATUS current DESCRIPTION "A notification indicating that the QFP memory usage is equal to or below the falling threshold on this memory resource. This notification will be sent, whenever the QFP memory usage (ceqfpMemoryResInUse) is equal to or below the falling threshold (ceqfpMemoryResFallingThreshold). An agent may throttle the generation of consecutive ceqfpMemoryResFallingThreshNotif notification so that there is at least a five second (suggested default) gap between notification of this type." ::= { ciscoEntityQfpMIBNotifs 2 } ciscoEntityQfpMIBGroups OBJECT IDENTIFIER ::= { ciscoEntityQfpMIBConform 2 } ciscoEntityQfpMIBComplianceRev1 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for CISCO-ENTITY-QFP-MIB" MODULE -- this module MANDATORY-GROUPS { ciscoEntityQfpSystemGroup, ciscoEntityQfpUtilizationGroup, ciscoEntityQfpUtilizationAlgoGroup } GROUP ciscoEntityQfpMemoryResourceGroup DESCRIPTION "This group is optional for the QFP entity, which does not use the listed memory resources." GROUP ciscoEntityQfpMemoryResNotifGroup DESCRIPTION "This group is optional for the QFP, which does not support the memory resource." GROUP ciscoEntityQfpNotifGroup DESCRIPTION "This group is optional." OBJECT ceqfpMemoryResRisingThreshold MIN-ACCESS read-only DESCRIPTION "Write access is not mandatory." OBJECT ceqfpMemoryResFallingThreshold MIN-ACCESS read-only DESCRIPTION "Write access is not mandatory." ::= { ciscoEntityQfpMIBCompliances 1 } ciscoEntityQfpSystemGroup OBJECT-GROUP OBJECTS { ceqfpSystemTrafficDirection, ceqfpSystemState, ceqfpNumberSystemLoads, ceqfpSystemLastLoadTime } STATUS current DESCRIPTION "This group contains collection of QFP system information." ::= { ciscoEntityQfpMIBGroups 1 } ciscoEntityQfpUtilizationAlgoGroup OBJECT-GROUP OBJECTS { ceqfpFiveSecondUtilAlgo, ceqfpOneMinuteUtilAlgo, ceqfpFiveMinutesUtilAlgo, ceqfpSixtyMinutesUtilAlgo } STATUS current DESCRIPTION "This group contains collection of QFP utilization algorithm objects." ::= { ciscoEntityQfpMIBGroups 2 } -- Units of Conformance ciscoEntityQfpUtilizationGroup OBJECT-GROUP OBJECTS { ceqfpUtilInputPriorityPktRate, ceqfpUtilInputPriorityBitRate, ceqfpUtilInputNonPriorityPktRate, ceqfpUtilInputNonPriorityBitRate, ceqfpUtilInputTotalPktRate, ceqfpUtilInputTotalBitRate, ceqfpUtilOutputPriorityPktRate, ceqfpUtilOutputPriorityBitRate, ceqfpUtilOutputNonPriorityPktRate, ceqfpUtilOutputNonPriorityBitRate, ceqfpUtilOutputTotalPktRate, ceqfpUtilOutputTotalBitRate, ceqfpUtilProcessingLoad } STATUS current DESCRIPTION "This group contains collection of QFP utilization information." ::= { ciscoEntityQfpMIBGroups 3 } ciscoEntityQfpMemoryResourceGroup OBJECT-GROUP OBJECTS { ceqfpMemoryResTotal, ceqfpMemoryResInUse, ceqfpMemoryResFree, ceqfpMemoryResLowFreeWatermark, ceqfpMemoryResRisingThreshold, ceqfpMemoryResFallingThreshold } STATUS current DESCRIPTION "This group contains collection of QFP memory resource information." ::= { ciscoEntityQfpMIBGroups 4 } ciscoEntityQfpNotifGroup NOTIFICATION-GROUP NOTIFICATIONS { ceqfpMemoryResRisingThreshNotif, ceqfpMemoryResFallingThreshNotif } STATUS current DESCRIPTION "This group contains collection of QFP notifications." ::= { ciscoEntityQfpMIBGroups 5 } ciscoEntityQfpMemoryResNotifGroup OBJECT-GROUP OBJECTS { ceqfpMemoryResThreshNotifEnabled, ceqfpMemoryResCurrentRisingThresh, ceqfpMemoryResCurrentFallingThresh } STATUS current DESCRIPTION "This group contains memory resource notification control objects." ::= { ciscoEntityQfpMIBGroups 6 } END